1. The pressure of a gas is 100.0 kPa and its volume is 500.0 ml. If the volume increases to 1,000.0 ml, what is the new pressure of the gas?



2. If a gas at 25.0 °C occupies 3.60 liters at a pressure of 10 kPa, what will be its volume at a pressure of 25 kPa?



3. When the pressure on a gas increases three times, by how much will the volume increase or decrease?


4. Boyle's Law deals what quantities?

Answers

Answer 1

Answer:

1) The new pressure of the gas is 500 kilopascals.

2) The final volume is 1.44 liters.

3) Volume will decrease by approximately 67 %.

4) The Boyle's Laws deals with pressures and volumes.

Explanation:

1) From the Equation of State for Ideal Gases we construct the following relationship:

[tex]\frac{P_{2}}{P_{1}} = \frac{V_{1}}{V_{2}}[/tex] (1)

Where:

[tex]P_{1}, P_{2}[/tex] - Initial and final pressure, measured in kPa.

[tex]V_{1}, V_{2}[/tex] - Initial and final pressure, measured in mililiters.

If we know that [tex]P_{1} = 100\,kPa[/tex], [tex]V_{1} = 500\,mL[/tex] and [tex]V_{2} = 1000\,mL[/tex], then the new pressure of the gas is:

[tex]P_{2} = P_{1}\cdot \left(\frac{V_{1}}{V_{2}} \right)[/tex]

[tex]P_{2} = 500\,kPa[/tex]

The new pressure of the gas is 500 kilopascals.

2) Let suppose that gas experiments an isothermal process. From the Equation of State for Ideal Gases we construct the following relationship:

[tex]\frac{P_{2}}{P_{1}} = \frac{V_{1}}{V_{2}}[/tex] (1)

Where:

[tex]P_{1}, P_{2}[/tex] - Initial and final pressure, measured in kPa.

[tex]V_{1}, V_{2}[/tex] - Initial and final pressure, measured in mililiters.

If we know that [tex]V_{1} = 3.60\,L[/tex], [tex]P_{1} = 10\,kPa[/tex] and [tex]P_{2} = 25\,kPa[/tex] then the new volume of the gas is:

[tex]V_{2} = V_{1}\cdot \left(\frac{P_{1}}{P_{2}} \right)[/tex]

[tex]V_{2} = 1.44\,L[/tex]

The final volume is 1.44 liters.

3) From the Equation of State for Ideal Gases we construct the following relationship:

[tex]\frac{P_{2}}{P_{1}} = \frac{V_{1}}{V_{2}}[/tex] (1)

Where:

[tex]P_{1}, P_{2}[/tex] - Initial and final pressure, measured in kPa.

[tex]V_{1}, V_{2}[/tex] - Initial and final pressure, measured in mililiters.

If we know that [tex]\frac{P_{2}}{P_{1}} = 3[/tex], then the volume ratio is:

[tex]\frac{V_{1}}{V_{2}} = 3[/tex]

[tex]\frac{V_{2}}{V_{1}} = \frac{1}{3}[/tex]

Volume will decrease by approximately 67 %.

4) The Boyle's Laws deals with pressures and volumes.


Related Questions

Find Jay's instantaneous speed at 35 minutes.

Find jays instantaneous speed at 35 minutes.

Answers

What do u mean by the question?

How do waves form?

Lesson 2.13

Question 4 options:

Ocean waves don't form


Ocean waves form as wind is absent.


Ocean waves form as wind moves across the surface, transferring its energy to the water.


Ocean waves form as salinity increases.

Answers

Answer:

It's the 4th one. waves are created by the wind

Answer:

C. Ocean waves form as wind moves across the surface, transferring its energy to the water.

Explanation:

hope this helps! c:

(Help would be greatly appreciated) What is the molarity of a solution which contains 22.41 grams of NaCl in 50.0 mL of solution?
1. 0.488M
2. 7.67mol
3. 7.67M
4. 0.000767M

Answers

Answer:

7.67

Explanation:

According to molar concentration, the molarity of solution which contains 22.41 grams of NaCl in 50.0 ml of solution is 7.67 M.

What is molar concentration?

Molar concentration is defined as a measure by which concentration of chemical substances present in a solution are determined. It is defined in particular reference to solute concentration in a solution . Most commonly used unit for molar concentration is moles/liter.

The molar concentration depends on change in volume of the solution which is mainly due to thermal expansion. Molar concentration is calculated by the formula, molar concentration=mass/ molar mass ×1/volume of solution in liters.

In terms of moles, it's formula is given as molar concentration= number of moles /volume of solution in liters.Substitution of values in the given formula gives, molarity= 22.41/58.44×1/0.05=7.67 M.

Thus, the  molarity of solution which contains 22.41 grams of NaCl in 50.0 ml of solution is 7.67 M.

Learn more about molar concentration,here:

https://brainly.com/question/21841645

#SPJ2

what is a food chain OR web, and what is it useful for?

Answers

Answer:

-

-

Food webs can be used to study bottom-up or top-down control of community structure.

Explanation:

Food chains are important because they show the intricate relationships in ecosystems. They can reveal how each organism depends on someone else for survival. Food chains also display what happens when a problem occurs and a producer or consumer is lost.

-

-

-

-

Anyone help please more & you get extra points

Answers

Answer:

qns-4

1-multicellular organism

2-unicellular organism

3-unicellular organism

4-multicellular organism

5-unicellular organism

6-multicellular organism

7-unicellular organism

I’ll really appreciate it if you help me out on these 2 questions.

Answers

Answer:

13. A

14. C

Explanation: i tried my best

1)Change the following temperatures to Kelvin: 100 C and -20 C
2)Change the following temperatures to Celsius: 273 K and 15 K

Answers

Answer:

373 K; 253 K

0°C ; -258°C

Explanation:

In order to change Temperatures to Absolute Value (Kelvin) you shoud do this sum:

T° in C  + 273 = T° in K

For question 1:

100°C + 273 = 373K

-20°C + 273 = 253K

For question 2:

T° K - 273 = T° C

273 K - 273 = 0°C

15 k + 273 = -258 °C

Answer:

-67.8

Explanation:

classify matter as elements mixtures and compounds

Answers

Answer:

An element contains just one type of atom. A compound contains two or more different atoms joined together. A mixture contains two or more different substances that are only physically joined together, not chemically. A mixture can contain both elements and compounds.

what type of galaxy is this

Answers

Explanation:

it is an spiral as it are rounded so

It is a spiral type of galaxy.

As the moon orbits the ______________, its gravitational pull is______________ on the side of the earth closest to the ______________.This ______________ force pulls on the water facing the moon,creating a ______________. The moon also ______________ on the solidearth, causing the water on the far side of earth to ______________as well. These bulges in the water are the ______________.The areas in between the close and far side of the earth which are not in ______________ with the moon experience ______________.


pls help i give brainlyest

Answers

Answer:

Earth

Strongest

Moon

Gravitational

Tide

Pulls

Bulge

Waves

Proximity

Low Tide

A trait that is helpful to a species will become more common in that
species over time. This is called what.

A. genetic variation
B. transition
C. overproduction
D. selection

Answers

B is the right answer

If a star is 300 light years away from Earth, how long does it take light from that star to reach Earth?
A. 300 days
B. 300 hours
C. 300 years
D. 300 light years

Answers

It would take 300 light years to reach Earth

list 5 things which we can make using each of the following materials​

Answers

Answer:

Glass

1.microscopes

2.mirrors

3.glass shelves

4.wrist watch glass

5.magnifying glass

Metal

1.keys

2.automobile body parts

3.coins

4.window frames

5.screws and nails

Plastic

1.bottles

2.boxes

3.balls

4.carry bags

5.buckets and mugs

Wood

1.chairs

2.tables

3.shoe stand

4.dressing table

5.shelves

MORE THEN ONE ANSWER Factors affecting energy transfer

Lesson 2.14-2.15

Question 9 options:

Wind moving over a relatively flat water surface has less area to come in contact with the water, and this reduces energy transfer.


Larger waves have extra spaces and areas to trap air, increasing the transfer of the wind's energy to the water.


Wind moving over a relatively flat water surface has GREATER area to come in contact with the water, and this INCREASES energy transfer.


SMALLER waves have extra spaces and areas to trap air, increasing the transfer of the wind's energy to the water.

Answers

Answer:

1.) Wind moving over a relatively flat water surface has less area to come in contact with the water, and this reduces energy transfer.

2.) Larger waves have extra spaces and areas to trap air, increasing the transfer of the wind's energy to the water.

Explanation:

I got it right on the test.

Wind moving over a relatively flat water surface has less area to come in contact with the water, and this reduces energy transfer and Larger waves have extra spaces and areas to trap air, increasing the transfer of the wind's energy to the water.

What is energy transfer?

When energy of any body travels from the one body to the another body, then transfer of energy takes place.

In the oceans, winds transfer their energy to the ocean or to the sea by the interaction with the surface water. When on the surface of ocean or sea up and down movement of water occurs then the interaction of that water with wind takes place and transfer of energy from wind to sea happen. More roughness or more height of the water on the surface of sea observed ten more transfer of energy from wind to sea occur.

Hence, option (1) & (2) is correct i.e. wind moving over a relatively flat water surface reduces energy transfer and Larger waves increasing the transfer of the wind's energy to the water.

To know more about energy transfer, visit the below link:

https://brainly.com/question/2667612

how would I solve this problem?

Answers

Answer:

D

Explanation:

The goal in this set up is to make sure all units cancel each other.

Since we need to go from grams to atoms, our final unit should be atoms.

Using method of elimination, let's see why other options are wrong.

A - Although 'g' is cancelled out, we are left with moles^2 / atoms

B - Although 'g' is cancelled out, we are left with moles^2 / atoms

C - Although 'mol' is cancelled out, we are left with g^2 / atoms

What is the molarity of a solution that contains 3.66 mol KCl in 7.98 L solution?

Answers

Answer:

.4586M

Explanation:

It's simple, just devide the mol value by the volume value. So 3.66mol/7.98L=.4586M

When magnesium reacts with sulfuric acid the products are magnesium sulfate and hydrogen. If there are 15 grams of magnesium at the start of the reaction, how much magnesium will be present in the magnesium sulfate

Answers

Answer: 15 grams of magnesium will be present in the magnesium sulfate

Explanation:

According to the law of conservation of mass, mass can neither be created nor be destroyed. Thus the mass of products has to be equal to the mass of reactants. The number of atoms of each element has to be same on reactant and product side.

The balanced chemical reaction is:

[tex]Mg+H_2SO_4\rightarrow MgSO_4+H_2[/tex]

As the mass remains conserved at the end of the reaction, there will be 15 grams of Magnesium in magnesium sulphate.

What results when equal but opposite charges are present in two regions of a polar molecule? A. dipole B. ionic bond C. Electron sea D. crystal lattice

Answers

Answer: A. dipole

Explanation:

Dipole can be defined as the separation of the equal and opposite charges present in the molecule via ionic bonding. The water molecule comprising of two molecules of hydrogen being positively charged and one molecule of oxygen being negatively charged are connected via ionic bonding thus water molecule is an example of dipole molecule. There is unequal distribution of the electrical density throughout the molecule.

The polar molecule results in a dipole when equal but opposite charges are present in two regions.

Dipole:  

Dipole arises when a molecule have opposite and equal charge in the ends.

For example - water molecule

In water molecule Oxygen is negatively charged and hydrogen have low electronegativity, this difference in electronegativities arise dipole in molecule.

Therefore, the polar molecule results in a dipole when equal but opposite charges are present in two regions.

To know more about Dipole,

https://brainly.com/question/18382778

What is the charge on an atom after it gains two electrons during the formation of a bond?
One negative charge
One positive charge
Two negative charges
Two positive charges

Answers

Answer:

two negative charges is the answer of your question

What are the general trends in first ionization energy across a period (LR) within the
periodic table? From bottom to top within a group?

Answers

Moving left to right within a period or upward within a group, the first ionization energy generally increases. As the atomic radius decreases, it becomes harder to remove an electron that is closer to a more positively charged nucleus. (this is copywriter so please just interpret)

what is a salient factor?

Answers

Answer:

technology is a silent factor

Explanation:

learned about it in computer class.

how much heat is released as 5.00G of PB cool from 75.0° C to 25.0° C

Answers

Answer:

32.25 J

Explanation:

Heat, H = ?

Mass, m = 5g = 5 / 1000 = 0.005 Kg

Initial Temperature = 75.0° C

Final Temperature = 25.0° C

Temperature change, ΔT = Final - Initial = 50° C

Specific heat capacity of lead, C = 129 (J/kg°C)

The relationship between these quantities is given by the equation

H = mCΔT

H = 0.005 * 129 * 50

H = 32.25 J

Seawater is a good source of magnesium. Magnesium is dissolved in the seawater as Mg²⁺. SUGGEST a substance that could be used to precipitate magnesium out of the water. Write a BALANCED CHEMICAL EQUATION and IDENTIFY THE REACTION TYPE to support your thinking

Answers

Answer:

SO₄⁻² (aq)  +  Mg²⁺ (aq)  ⇄  MgSO₄ (s) ↓

Precipitation reaction

Explanation:

Mg²⁻ is one of the metals at group 2 in the Perodic Table. This group is called, the alkaline earth metals.

To make precipitate the Mg²⁺ we can use a salt of sulfate, either flouride or phosphate. Those are three salts that can precipitate this metal.

We use sodium as cathion so, first of all we dissociate them:

Na₂SO₄ (aq) →  2Na⁺  (aq)  +  SO₄⁻² (aq)

NaF (aq) →  Na⁺ (aq) +  F⁻ (aq)

Na₃PO₄ (aq) →  3Na⁺ (aq)  +  PO₄⁻³ (aq)

In all cases, the reaction is of the precipitation type and is conditioned by the Kps, the solubility product constant. Let's bond the anions with Mg²⁺.

SO₄⁻² (aq)  +  Mg²⁺ (aq)  ⇄  MgSO₄ (s) ↓    Kps

2F⁻ (aq)  +  Mg²⁺ (aq)  ⇄   MgF₂ (s) ↓      Kps

2PO₄⁻³ (aq)  +  3Mg²⁺ (aq)  ⇄  Mg₃PO₄ (s) ↓   Kps  

HELPP!!
in reaction 3Fe+2O2=Fe3O4 if I add 20g of Fe to my solution how many moles of Fe3O4 will produce???

Answers

Answer:

0.119 moles

Explanation:

molar mass of Fe = 55.845g

to find moles = mass/ molar mass

so moles of Fe = 20/55.845

= 0.358 moles

for the equation you are given

for every three Fe, it produces 1 Fe3O4 , meaning the ratio is 3:1

if you have 0.358 moles of Fe, that means the number of moles of Fe3O4  will equal to one third of that,

thus

moles of Fe3O4 = 1/3 x 0.358 = 0.119

Which of the following best explains how minerals get into streams?

A. Rainwater that is high in minerals from the atmosphere falls into the stream.
B. The stream absorbs minerals from the plants growing in and around its banks.
C. Rainwater dissolves minerals out of the rocks and soil along the stream during runoff.
D. When water evaporates from the ocean, it takes minerals with it and redeposits them as rainwater into the stream.
please help me

Answers

Answer:

C:Rainwater dissolves minerals out of the rocks and soil along the stream during runoff

the answer is C have a great rest of your day

Question 5 of 5
When planning space exploration, scientists face many
challenges. One issue is the weight of the items being
transported. They can use the engineering design process
to help minimize the weight of materials on board a
spacecraft.
You have designed a prototype of a new, lighter material. What should be the
next step in your process?
A. Update your initial design for the new type of material.
B. Test to see
whether your material is strong and works well.
C. Figure out what problems people want to solve.
D. Brainstorm new ways to design materials.

Answers

Answer:B

Explanation: got it right on test

Test to see whether your material is strong and works well  should be the next step in your process. Therefore, the correct option is option B.

What is space exploration?

Space science and technology are used in space exploration to learn more about the universe. While astronomers use telescopes to explore the universe, both unmanned robotic space missions and human spaceflight also participate in the physical exploration of space.

When planning space exploration, scientists face many challenges. One issue is the weight of the items being transported. They can use the engineering design process to help minimize the weight of materials on board a spacecraft.  You have designed a prototype of a new, lighter material. Test to see whether your material is strong and works well  should be the next step in your process.

Therefore, the correct option is option B.

To know more about space exploration, here:

https://brainly.com/question/12271960

#SPJ5

What is the solution to the problem expressed to the correct number of significant figures?
7.21= ?
A. 1.688
OB.
1.69
O C.
1.7:
OD
1.70

Answers

Answer:

(102 900 ÷ 12) + (170 × 1.27) = 8800

Step 1. Evaluate the expressions inside the parentheses (PEMDAS)

102 900 ÷ 12 = 8575

170 × 1.27 = 215.9

In multiplication and division problems, your answer can have no more significant figures than the number with the fewest significant figures.

Thus, the underlined digits are not significant, but we keep them in our calculator to avoid roundoff error.

Step 2. Do the addition (PEMDAS).

  8575

+    215.9

= 8790.9

Everything that you add to an insignificant digit gives an insignificant digit as an answer.

Thus, the underlined digits are not significant.

We must drop them and round up the answer to 8800.

Explanation:

What volume will 3.50 mol of ammonia gas occupy at conditions of standard temperature and pressure?

Answers

Answer:

Q:

What volume will 3.50 mol of Xe gas occupy at STP?

A:

78.4 L

Explanation:

The volume occupied by 3.5 moles of ammonia gas at standard temperature and pressure (STP) is 78.45 L

Data obtained from the question Number of mole (n) = 3.5 moles Pressure (P) = STP = 1 atm Temperature (T) = STP = 273 KGas constant (R) = 0.0821 atm.L/Kmol Volume (V) =?

How to determine the volume

The volume of the gas at standard temperature and pressure (STP) can be obtained by using the ideal gas equation as illustrated below:

PV = nRT

1 × V = 3.5 × 0.0821 × 273

V = 78.45 L

Learn more about ideal gas equation:

https://brainly.com/question/4147359

Can someone pls help me with this its due in 20 minutes.

Answers

Answer:

15. The velocity of a sound wave is affected by two properties of matter: the elastic properties and density.

16. The greater the density of a medium, the slower the speed of sound. This observation is analogous to the fact that the frequency of a simple harmonic motion is inversely proportional to m, the mass of the oscillating object.

17. Temp °C 0 m/s2 m/s

50 360.51 361.62

18. Molecules at higher temperatures have more energy, thus they can vibrate faster. Since the molecules vibrate faster, sound waves can travel more quickly. The speed of sound in room temperature air is 346 meters per second. ... The speed of sound is also affected by other factors such as humidity and air pressure.

HELP PLEASE , ITS DUE BY 6 ❤️10. If temperature were increased at the same rate for all four substances, which substance
would turn into a gas first?

Answers

Answer:

Dependant

Explanation:

Depending on the kind of substance you have (since ur answer of what substances was vauge) you would want to look at the molecular structure of the substances.

Understanding intermolecular bonds are key here (research this)

For example, Bromine is found as Br2 and only exerts London dispersion forces as there is no difference in polarity. And because this force is weaker, it has a lower boiling point

Another example being something like Hydrochloric acid (HCl). This is where Hydrogen acts as the positive atom while chlorine is the negative atom. This creates a stronger force and thus, a higher boiling point than Br2

Finally, there is Something like H2O where the force in play is Hydrogen bonding as Nitrogen, Oxygen, Fluorine where the bonds are strongest due to the electronegativity is at the greatest difference between these and Hydrogen. and thus having a higher boiling point.

So depending on the substance's bond, that will help determine the boiling point. If they fall under the same group, go based on the greatest difference in electronegativity.

I don't know if this is what you're looking for but, hope this helps. :)

Other Questions
why conflict confrontation is not healthy for sustaining positive relationships? **Absurd answers won't be tolerated** They're about 50 students in a class that took a test. 21 of those students passed. If 13 students made a F, find the percent of 50 to 21. Explain. If a star is 300 light years away from Earth, how long does it take light from that star to reach Earth?A. 300 daysB. 300 hours C. 300 yearsD. 300 light years Can somone PLEASE help me with this1: Which element does figurative language rely on?A dictionary definitionsB: sources outside the storyC: the reader's imaginationD: facts and details2: Which option describes a simile?Athe reader's use of imagination to visualize a sceneB a comparison of two unlike things that does not use the word like or asC a description that gives a thing or idea human characteristicsD a comparison of two unlike things using the word like or as3:Which option describes the rhythm of a poem?A words beginning with the same consonant soundB a pattern of stressed and unstressed syllablesC rhyme patterns at the end of lines in a poemD a word that imitates the sound it describes4:What is the short form used to illustrate a rhyme scheme?A a series of capital lettersB a brief description of how each line rhymesC a list of line numbersD a set of special punctuation marks that show a pattern5: Which feature makes a narrative poem different from other poems?A It uses figurative language.B It offers a description or reflection.C It tells a story.D It uses stylistic techniques. simplify this rational expression. Factor completely I need help on 7 please ASAP QUICK! heres the question. select the equations where x=3 is a soultionanswers:x-3=01+x=29-x=36=2x1/5x=3x2=9 btw its one of those 2's that are on top and small its multipul choice also! ESSAY: SHORT STORY REWRITE Imagine yourself in any one of the three stories you have just read. You may take the place of one of the existing characters, or you can simply insert yourself into the story. What would have been different if you were the character or if you were there? OBJECTIVES Write a 250-word story. Instructions: Choose any one of the stories, following the major events that take place in them, but change the actions and characters in the story. For example, what would you have differently if you were in Della's position? Or how would you have defeated General Zaroff? Write a story of at least 250 words. If you owned a house, and the assessed value was $435,000.00, how much in property taxes would you have to pay per year if the rate was 0.79%? (be sure to use $ and a decimal. No need to use a comma)a bit of help someone is retiring next year. what would be an appropriate amount of risk to take with their investments A. Highest Risk, Highest GrowthB. Medium risk, medium growthC. lower risk, lower growthD. no risk just savings account The development of regional trade associations in Africa represents an effort to A. deregulate the regional African economy. B. encourage foreign investment in African nations. C. remove barriers to trade between African nations. D. expand trade between Africa and other world regions. heyy I need help! thankss Which parts of the UK are most likely to experience high levels ofprecipitation? What is another name for fiber? Read the excerpt from The Monkey's Paw.Mr. White took the paw from his pocket and eyed it dubiously. "I don't know what to wish for, and that's a fact," he said, slowly. "It seems to me I've got all I want.""If you only cleared the house, you'd be quite happy, wouldn't you?" said Herbert, with his hand on his shoulder. "Well, wish for two hundred pounds, then; that'll just do it."His father, smiling shamefacedly at his own credulity, held up the talisman, as his son, with a solemn face, somewhat marred by a wink at his mother, sat down at the piano and struck a few impressive chords."I wish for two hundred pounds," said the old man distinctly.A fine crash from the piano greeted the words, interrupted by a shuddering cry from the old man. His wife and son ran toward him.Which phrase indicates a change in mood within the excerpt?struck a few impressive chordssmiling shamefacedly at his own credulitya fine crash from the pianointerrupted by a shuddering cry What is the sum of 24 and 72? Write the answer in standard form. Ask me good questions and i might give you brainliest The strip mining of phosphate on the island of Nauru has resulted in __________. A. massive immigration and overcrowding on the island B. environmental and economic problems for the country C. economic success and a high standard of living for many D. financial competition between ethnic groups that has led to civil war Please select the best answer from the choices provided A B C D The total number of students in the seventh grade is 9 more than 4 times as many students as are in the art class. there are 101 students in the seventh grade. how many students are in the art class. What is the solution to the problem expressed to the correct number of significant figures?7.21= ?A. 1.688OB.1.69O C.1.7:OD1.70