7.35 and 7.36 For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the maximum absolute values of the shear and bending moment.
Answers
Maximum absolute values of the shear = 28 KN
Maximum absolute values of bending moment = 5.7 KN.m
How to draw Shear Force and Bending Moment Diagram?A) We can see the beam loaded in the first image attached.
For the shear diagram, let us calculate the shear from point load to point load.
From A to C, summing vertical to zero gives; ∑fy = 0: -20 - V = 0
V = -20 KN
From C to D, summing vertical to zero gives; ∑fy = 0: -20 + 48 - V = 0
V = 28 KN
From D to E, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - V = 0
V = 8 KN
From E to B, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - 20 - V = 0
V = -12 KN
For the bending moment diagram, let us calculate the bending moment from point load to point load.
At point A, the bending moment would be zero. Thus, M_A = 0 KN.m
At point C, taking moment about point C and equating to zero gives;
M_C = 0. Thus; 20(0.225) + M = 0
M = -4.5 KN.m
At point D, taking moment about point D and equating to zero gives;
M_D = 0. Thus; 20(0.525) - 48(0.3) + M = 0
M = 3.9 KN.m
At point E, taking moment about point E and equating to zero gives;
M_D = 0. Thus; 20(0.75) - 48(0.525) + 20(0.225) + M = 0
M = 5.7 KN.m
At point B, taking moment about point E and equating to zero gives;
M_E = 0. Thus; 20(1.05) - 48(0.825) + 20(0.525) + (20 * 0.3) + M = 0
M = 2.1 KN.m
2) From the attached diagrams, we can deduce that;
Maximum absolute values of the shear = 28 KN
Maximum absolute values of bending moment = 5.7 KN.m
Read more about shear force & bending moment diagram at; https://brainly.com/question/14834487
#SPJ1
Related Questions
Gears A and B of mass 10 kg and 50 kg have a radii of gyration about their respective mass centers of k_A = 80 mm and k_B = 150 mm. If gear A is subjected to the couple moment M = 10 Nm when it is at rest, determine the angular velocity of gear B when t = 5s.
Answers
According to the given problem, angular velocity of gear B when t=5s is
is approximately 0.0142 rad/s.
We can use the principle of conservation of angular momentum to solve this problem.
Initially, gear A is at rest and gear B is not moving, so the total angular momentum of the system is zero.
When gear A is subjected to the couple moment M, it begins to rotate with an angular acceleration given by:
α_A = M / I_A
where I_A is the moment of inertia of gear A about its center of mass.
Since gear A is a solid disk, we can use the formula for the moment of inertia of a disk:
I_A = (1/2) m_A k_[tex]A^{2}[/tex][tex]m^{2}[/tex]
where m_A is the mass of gear A.
Substituting the given values, we get:
I_A = 0.04 kg·[tex]m^{2}[/tex]
Using the same formula, we can find the moment of inertia of gear B:
I_B = (1/2) m_B k_[tex]B^{2}[/tex]
I_B = 5.625 kg·[tex]m^{2}[/tex]
Since the total angular momentum of the system is conserved, we have:
L = I_A ω_A + I_B ω_B
where ω_A and ω_B are the angular velocities of gears A and B, respectively.
At t = 5 s, gear A has been rotating for 5 seconds, so its angular velocity is:
ω_A = α_A t = 2 rad/s
Substituting this value and the given values for I_A and I_B, we can solve for ω_B:
ω_B = (L - I_A ω_A) / I_B
We don't know the value of the total angular momentum L, but we can use the fact that the initial total angular momentum is zero.
Thus, we have:
L = I_A ω_A
Substituting this value and the given values for I_A and I_B, we get:
ω_B = (I_A ω_A) / I_B
ω_B = 0.0142 rad/s
Therefore, the angular velocity of gear B when t = 5 s is approximately 0.0142 rad/s.
For more such questions on Angular velocity:
https://brainly.com/question/29897297
#SPJ11
Moment of inertia, also known as rotational inertia, is a property of a rigid body that determines how difficult it is to change its rotational motion about a particular axis. It is the rotational analog of mass in linear motion. The moment of inertia of a body depends on its shape, mass distribution, and axis of rotation.
The moment of inertia of a rotating body is given by the product of the mass and the square of the radius of gyration, i.e., I = mk^2. Using this, we can calculate the moment of inertia of gears A and B:
I_A = 10 kg * [tex](0.08m)^{2}[/tex] = 0.064 kg*[tex]m^{2}[/tex]
I_B = 50 kg * [tex](0.15m)^{2}[/tex] = 1.125 kg*[tex]m^{2}[/tex]
The torque applied to gear A is M = 10 Nm. According to Newton's second law for rotational motion, the angular acceleration of gear A is given by:
α_A = M / I_A = 10 Nm / 0.064 kg*[tex]m^{2}[/tex] = 156.25 rad/[tex]s^{2}[/tex]
Since gear B is meshed with gear A, it will also rotate. The angular velocity of gear B can be found using the equation of rotational motion:
Ω_B = Ω_A + alpha_A * t
Since gear A is initially at rest, Ω_A = 0. Thus, after 5 seconds of rotation, the angular velocity of gear B is:
Ω_B = 0 + 156.25 rad/[tex]s^{2}[/tex] * 5 s = 781.25 rad/s
Therefore, the angular velocity of gear B after 5 seconds is 781.25 rad/s.
To know more about Newton's second law,
https://brainly.com/question/13447525
#SPJ11
1. True or False, the Queue ADT is organized according to the principle of FIFO?
2. Draw a Queue that results after the following values are inserted into an empty queue, in this order: 10, 20, 30, 40. Be sure to label front and end. Note that you must draw this Queue the way it is shown in the class lesson notes to receive credit for this answer.
These are the two pictures I have from the notes.
3. Write the addIterator method from the doubly-linked list class. Be sure to handle precondition(s), edge case(s), and general case. --> I'm not sure how to write it.
Mutator: addIterator: inserts an element after the node currently pointed to by the iterator.
Answers
The statement "The the Queue ADT is organized according to the principle of FIFO" is false. The "add Iterator" term you mentioned is not a standard operation associated with the Queue ADT, and might be more applicable to other data structures, such as a List or a Linked List.
The Queue ADT (Abstract Data Type) is organized according to the principle of FIFO (First In, First Out), meaning that the first element added to the queue will be the first one to be removed. So, the statement is True.the terms "Mutator" and "Iterator" are related to different aspects of data structures. A Mutator is a method that modifies the state of an object, while an Iterator is an object that enables traversal through a collection of elements in a specific order.
In the context of a Queue, the main mutator is the "enqueue" operation, which adds an element to the rear of the queue. The main iterator operation for a Queue is "dequeue", which removes the element from the front of the queue. The "addIterator" term you mentioned is not a standard operation associated with the Queue ADT, and might be more applicable to other data structures, such as a List or a Linked List.
To learn more about Linked .
https://brainly.com/question/7788080
#SPJ11
Consider the following recursive function, assuming 0 msn and n 2 1. int fun (int n, int m){ if ((n == 1)|| (m == 0) || (m = n)) return (1); else return (fun (n - 1, m) + fun (n - 1, m – 1)); } (a) What are fun (4,2)? 6 fun(5,3)?_10 ? fun(6,4)? 15 fun(8,3)? 56 fun (9,2)? 36 (b) What does this function do, given any m and n within the constraints? Compute the function for some smaller values of m and n; try to generalize; observe that the recursion ends in finite time; observe the similarity with how we wrote the recursive function for Fibonacci numbers in class; and then give a precise one sentence description of the purpose of the function.
Answers
(a) The values of the given recursive function fun are:
- fun(4,2) = 6
- fun(5,3) = 10
- fun(6,4) = 15
- fun(8,3) = 56
- fun(9,2) = 36
(b) This function calculates the binomial coefficient C(n, m), also known as "n choose m," which is the number of ways to choose m elements from a set of n elements. The function has a finite recursion and is similar to the recursive function for Fibonacci numbers.
If you need to learn more about recursive functions click here:
https://brainly.com/question/489759
#SPJ11
What's true about an Interface in C++? By convention Interface classes should contain only pure-virtual methods and maybe constants Unlike Java, an Interface is a convention with rules the program should follow rather than rules that are enforced by the compiler Interface Classes are used through multiple inheritance Interface classes don't need to be Abstract C++ has a particular operator for using an interface class
Answers
Answer:
In C++, an Interface is a convention with rules that programs should follow rather than rules that are enforced by the compiler. By convention, Interface classes should contain only pure-virtual methods and maybe constants, but this is not enforced by the compiler. Interface classes are typically used through multiple inheritance, and they are generally abstract classes, meaning that they cannot be instantiated.
C++ does not have a particular operator for using an interface class. Instead, a class can inherit from an interface class using the same syntax as for inheriting from a regular (non-interface) class.
It's worth noting that while C++ does not have built-in support for interfaces like Java or C#, the use of abstract classes as interfaces is a common practice in C++. Abstract classes can be used to define interfaces that specify the behavior that a derived class must implement, and they can be used to achieve much of the same functionality as interfaces in other languages.
Explanation:
hope this helped :o
In C++, an interface is a convention that specifies a set of methods and constants that a class must implement. Unlike in Java, an interface in C++ is not enforced by the compiler, but rather it is a convention that programmers must follow. Interface classes in C++ should contain only pure-virtual methods and constants.
This means that the interface class has no implementation of its own, but rather serves as a template for other classes to implement its methods.
Interface classes in C++ can be used through multiple inheritance, allowing a class to inherit from multiple interface classes and implement their methods. However, unlike abstract classes, interface classes do not need to be abstract, meaning they can have data members and non-pure virtual methods.
C++ has a particular operator, called the virtual function table (vtable) or virtual function pointer (vptr), for using an interface class. This operator allows a class to store pointers to virtual functions, including those inherited from interface classes, in a vtable. When a virtual function is called, the vptr is used to locate the appropriate entry in the vtable.
For more information on compilers visit:
brainly.com/question/17738101
#SPJ11
T/F While merging scenarios, one should keep both workbooks from which one wants to merge scenarios open, and work from the workbook to which one will add the scenarios.
Answers
The given statement "While merging scenarios, one should keep both workbooks from which one wants to merge scenarios open, and work from the workbook to which one will add the scenarios" is false because when merging scenarios in Excel, you do not need to keep both workbooks open.
Should scenarios be merged by keeping both workbooks open?When merging scenarios in Excel, it is not necessary to keep both workbooks open. Instead, it is more efficient to work from the workbook to which you intend to add the scenarios. To merge scenarios, you can open the destination workbook and navigate to the worksheet where you want the scenarios to be merged.
Then, go to the "Data" tab, click on "What-If Analysis," and select "Scenario Manager." In the Scenario Manager dialog box, you can add, edit, or delete scenarios and import them from other workbooks. This approach simplifies the process and ensures that the scenarios are accurately merged into the desired workbook.
Learn more about Excel
brainly.com/question/30324226
#SPJ11
Let Y and Z be two independent standard normal random variables (l.e. gaussians mean zero and variance 1 each). Define another random variable X as X=aY+Z
where a =8.801
What is the covariance between X , Y
Answers
The covariance between two random variables X and Y is a measure of how they change together. So, the covariance between X and Y is 8.801.
Covariance can be calculated using the formula Cov(X, Y) = E[(X - E[X])(Y - E[Y])]. In your case, X is defined as X = aY + Z, where Y and Z are two independent standard normal random variables with mean zero and variance 1 each, and a = 8.801.
Since Y and Z are independent, their covariance is 0, which means E[YZ] = 0. Also, the means of Y and Z are 0, so E[X] = a * E[Y] + E[Z] = 0.
Now, we can find the covariance between X and Y:
Cov(X, Y) = E[(X - E[X])(Y - E[Y])] = E[(aY + Z)(Y - 0)] = E[aY² + YZ] = a * E[Y²] + E[YZ].
As mentioned earlier, E[YZ] = 0, and E[Y²] is the variance of Y, which is 1. Therefore, Cov(X, Y) = a * 1 + 0 = 8.801. So, the covariance between X and Y is 8.801.
Learn more about covariance here:
https://brainly.com/question/28135424
#SPJ11
The uniform crate has a mass of 30 kg and rests on the cart having an inclined surface. Part A Determine the smallest acceleration that will cause the crate either to tip or slip relative to the cart. What is the magnitude of this acceleration? The coefficient of static friction between the crate and the cart is μ' = 0.6. Express your answer with the appropriate units Units Value a= 0.6 m 1 m 15
Answers
To determine the smallest acceleration that will cause the crate either to tip or slip relative to the cart, we need to consider the forces acting on the crate. The force of gravity is pulling the crate downwards, while the normal force of the inclined surface is perpendicular to the surface.
The force of static friction is parallel to the surface and prevents the crate from slipping. The minimum acceleration required for the crate to tip or slip can be calculated using the formula a = g * μ', where g is the acceleration due to gravity (9.8 m/s^2) and μ' is the coefficient of static friction (0.6). Substituting these values, we get a minimum acceleration of 5.88 m/s^2. Therefore, the smallest acceleration that will cause the crate either to tip or slip relative to the cart is 5.88 m/s^2.
The uniform crate has a mass of 30 kg and rests on a cart with an inclined surface. To determine the smallest acceleration that will cause the crate to either tip or slip relative to the cart, you must consider the static friction between the crate and the cart, which has a coefficient μ' = 0.6. The force of static friction (Fs) is given by Fs = μ' * Fn, where Fn is the normal force. In this case, Fn = m * g * cos(θ), and the tipping condition occurs when the gravitational force (m * g * sin(θ)) equals the static friction force. Solving for the smallest acceleration (a), you get a = (μ' * g * cos(θ)) / sin(θ) = (0.6 * 9.81 * cos(θ)) / sin(θ). The magnitude of this acceleration will depend on the angle θ and has units of m/s².
To know more about Uniform crate visit-
https://brainly.com/question/30207029
#SPJ11
larger cooling towers generally use ____________________-type fans.
Answers
Larger cooling towers generally use axial-type fans.
Cooling towers used in various industries to remove heat from processes or equipment by transferring it to the atmosphere. Cooling towers are equipped with fans to facilitate the exchange of heat between the water inside the tower and the surrounding air. Axial-type fans are commonly used in larger cooling towers due to their high airflow capacity and efficiency. These fans consist of a hub and multiple blades that rotate to draw air through the tower.
The axial design allows for the movement of air in a straight line parallel to the fan axis, providing effective cooling performance for larger cooling towers. The use of axial-type fans ensures efficient heat dissipation and optimal operation of the cooling tower system.
Learn more about cooling towers here:
https://brainly.com/question/13507664
#SPJ11
technician 1 says that an open contactor coil is indicated by a reading of 0 ohms on an ohmmeter. technician 2 says that a shorted contactor coil is indicated by an infinite reading on an ohmmeter. who, if either, is correct?
Answers
Technician 2 is correct that a shorted contactor coil is indicated by an infinite reading on an ohmmeter.
What is a contactor?A contactor is an electrical gadget that is used to control the power circuits in machines or equipment. Its purpose is to switch off and turn on the circuits in a piece of machinery or electrical equipment.
A shorted coil is a condition that occurs when the insulating coating on a wire has been damaged, resulting in a fault in the winding.
In this scenario, the coil will not function properly because it has been compromised. Technician 1 is incorrect because an open contactor coil should give a reading of infinity, not 0 ohms.
Learn more about electrical circuit at:
https://brainly.com/question/27936404
#SPJ11
short, successive cuts of fabric that help release tension while draping are known as:
Answers
The short, successive cuts of fabric that help release tension while draping are known as "notches." Notches are essential in garment construction, as they allow the fabric to be more easily manipulated and adjusted to fit the desired shape and form. They are typically created by making small, V-shaped cuts or slits in the fabric's seam allowance.
These cuts are beneficial for several reasons. First, they facilitate the draping process by enabling the fabric to lie flat and smooth on the garment's form. This allows designers to create accurate and well-fitted garments, particularly when working with curved seams or complex shapes.
Second, notches serve as important reference points for aligning pieces of fabric during the sewing process. They help ensure that seams are properly aligned, and they can also be used to indicate the location of darts, pleats, or other design elements.
Lastly, notches help minimize bulk and reduce strain on the fabric, which can be especially important when working with heavyweight or stiff materials. By releasing tension and allowing the fabric to relax, notches contribute to a more comfortable and professional-looking finished garment.
Overall, notches are a valuable tool in garment construction that enables designers to achieve precise and accurate results while maintaining the integrity and appearance of the fabric.
Learn more about Notches here:-
https://brainly.com/question/31669642
#SPJ11
The following fluids (air, H, N) at 350K and atmospheric pressure flow at velocity of 5 m/s over a 2 m long flat plate. The order of magnitude of the drag force from lowest to highest is a. air-H-N b. air-N-H Oc. H-N-air Od. H-air-N Oe. N-air-H Of. N-H-air
Answers
The order of magnitude of the drag force from lowest to highest is:
b. air-N-H < Od. H-air-N < a. air-H-N < Oe. N-air-H < Of. N-H-air < c. H-N-air
How did we arrive at this order?The drag force on a flat plate can be estimated using the formula:
F = 0.5 x rho x v² x Cd x A
where F is the drag force, rho is the density of the fluid, v is the velocity of the fluid, Cd is the drag coefficient, and A is the area of the plate.
Supposing that the plate is 1 m wide (in the direction perpendicular to the flow), the area of the plate is 2 m².
The drag coefficient for a flat plate depends on the Reynolds number of the flow, which is given by:
Re = rho x v x L / mu
where L is the length of the plate and mu is the dynamic viscosity of the fluid.
For air at 350K and atmospheric pressure, the density is approximately 1.16 kg/m³ and the dynamic viscosity is approximately 2.97e-5 Pa x s. Using these values, we can calculate the Reynolds number for air:
Re = 1.16 x 5 x 2 / 2.97e-5 = 390,582
The drag coefficient for a flat plate at this Reynolds number is approximately 0.664. Applying this value and the other values calculated, estimate the drag force on the plate:
F_air = 0.5 x 1.16 x 5² x 0.664 x 2 = 19.4 N
For hydrogen at 350K and atmospheric pressure, the density is approximately 0.084 kg/m³ and the dynamic viscosity is approximately 8.46e-6 Pa x s. Using these values, calculate the Reynolds number for hydrogen:
Re = 0.084 x 5 x 2 / 8.46e-6 = 99,409
The drag coefficient for a flat plate at this Reynolds number is approximately 1.24. Using this value and the other values we have calculated, estimate the drag force on the plate:
F_H = 0.5 x 0.084 x 5² x 1.24 x 2 = 4.2 N
For nitrogen at 350K and atmospheric pressure, the density is approximately 1.02 kg/m³ and the dynamic viscosity is approximately 1.86e-5 Pa x s. Using these values, we can calculate the Reynolds number for nitrogen:
Re = 1.02 x 5 x 2 / 1.86e-5 = 548,387
The drag coefficient for a flat plate at this Reynolds number is approximately 0.696. Using this value and the other values we have calculated, estimate the drag force on the plate:
F_N = 0.5 x 1.02 x 5² x 0.696 x 2 = 18.0 N
Therefore, the order of magnitude of the drag force from lowest to highest is:
b. air-N-H < Od. H-air-N < a. air-H-N < Oe. N-air-H < Of. N-H-air < c. H-N-air
learn more about drag force: https://brainly.com/question/27817330
#SPJ4
TRUE OR FALSEthe number of nodes in a non-empty tree is equal to the number of nodes in its left subtree plus the number of nodes in its right subtree plus 1.
Answers
The statement "the number of nodes in a non-empty tree is equal to the number of nodes in its left subtree plus the number of nodes in its right subtree plus 1" is true because it follows from this fundamental property of binary trees.
This is because of the "counting nodes" property of binary trees, which states that the total number of nodes in a non-empty binary tree can be defined recursively as the sum of the number of nodes in its left subtree, the number of nodes in its right subtree, and one more node for the root. This can be mathematically expressed as:
N(node) = N(left) + N(right) + 1
Where N(node) is the total number of nodes in the tree rooted at the current node, N(left) is the total number of nodes in the left subtree, and N(right) is the total number of nodes in the right subtree.
Learn more about binary trees https://brainly.com/question/31392563
#SPJ11
The crumple zone of a motor vehicle is designed to ____________ in a collision to absorb the impact force.
Answers
The crumple zone of a motor vehicle is designed to deform or crumple in a controlled manner during a collision in order to absorb the impact force. This safety feature is an essential part of modern car design and is engineered to minimize the risk of injuries to passengers and drivers in the event of an accident.
Crumple zones function by redirecting and dissipating the energy from a crash away from the vehicle's occupants. They achieve this by intentionally deforming, compressing, and buckling at specific points in the vehicle's structure. These areas are engineered to collapse in a controlled manner, effectively lengthening the time of the collision and reducing the acceleration experienced by the vehicle and its occupants. As a result, the forces experienced by passengers during an impact are reduced, lowering the likelihood of severe injuries or fatalities.
Additionally, crumple zones work in conjunction with other vehicle safety features, such as seat belts, airbags, and safety cell designs, to provide a comprehensive approach to passenger protection. By combining these technologies, modern motor vehicles are better equipped to protect occupants during various types of collisions, such as frontal impacts, side impacts, and rollovers.
In summary, the crumple zone of a motor vehicle is a crucial safety feature designed to absorb the impact force during a collision by deforming in a controlled manner. This helps to dissipate energy away from occupants, reducing the risk of injuries and fatalities.
Learn more about engineered here:-
https://brainly.com/question/31140236
#SPJ11
.A channel through which data flows between a program and storage is a ________________________.
a. path
b. folder
c. directory
d. stream
Answers
The correct answer is d. stream.
A stream is a channel through which data flows between a program and storage. It is a sequence of bytes that represent a continuous flow of data between the program and the storage device. Streams can be used to read and write data to files, network connections, and other sources of input and output. They are an essential part of modern programming languages and are used extensively in applications that handle large amounts of data. In summary, a stream provides a way for a program to read and write data to and from storage, making it an essential component of many software applications.
To know more about stream visit:
https://brainly.com/question/31779773
#SPJ11
design a cam to move a follower at a constant velocity of 100 mm/sec for 2 sec then return to its starting position with a total cycle time of 3 sec.
Answers
To design a cam to move a follower at a constant velocity of 100 mm/sec for 2 sec and then return to its starting position with a total cycle time of 3 sec, we can follow these steps:
Determine the maximum lift of the cam: The maximum lift of the cam is the distance the follower travels during the cycle. We can assume a maximum lift of 100 mm for this example.Determine the motion profile: We need the follower to move at a constant velocity of 100 mm/sec for 2 sec, then return to its starting position with a total cycle time of 3 sec. This means the follower will move a total distance of 200 mm in the first 2 sec, then move back to its starting position in the remaining 1 sec.Determine the cam profile: We can use a mathematical function to generate the cam profile. One commonly used function is the polynomial function, which can be represented as a series of coefficients. For this example, we can use a cubic polynomial function with the following coefficients:a0 = 0
a1 = 0
a2 = (12/4) * (100/2)^(-2)
a3 = -(6/4) * (100/2)^(-3)
This function will generate a cam profile with the desired motion profile.
Verify the cam profile: We can use a computer-aided design (CAD) software to create a 3D model of the cam and follower, and then simulate the motion to verify that the follower moves at the desired velocity and returns to its starting position within the specified cycle time.Manufacture the cam: Once the cam profile is verified, we can manufacture the cam using a CNC machine or other manufacturing methods.Assemble and test: Finally, we can assemble the cam and follower, and test the motion to ensure it meets the desired specifications.To know more about CAM, visit:
brainly.com/question/30325402
#SPJ11
Convert the following infix expression to a postfix expression. w* (x+ y)/z a. wx+y/z b. wx+yz/ c. wx y/z+ d. wxy+z/
Answers
The resulting postfix expression is option A, wx+y/z. The order of operations for this expression is to first perform the addition inside the parentheses, then perform the multiplication outside the parentheses, and finally perform the division.
Starting with the infix expression, we first see the multiplication operator, so we add it to the stack. The next symbol is an open parenthesis, so we add it to the stack as well. Moving on, we see the variable x, which we add to the output string. The next symbol is a plus sign, so we add it to the stack. After that, we see the variable y, which we add to the output string. At this point, we have reached the end of the parentheses, so we need to start popping operators off the stack until we reach the matching open parenthesis.
We pop the plus sign and add it to the output string, and then we pop the multiplication sign and add it to the output string. Next, we see the variable z, which we add to the output string, followed by the division operator, which we add to the stack. Finally, we see the variable w, which we add to the output string. At this point, we have reached the end of the expression, so we need to pop any remaining operators off the stack and add them to the output string. In this case, there is only one operator left, which is the division operator, so we pop it and add it to the output string.
To know more about parentheses visit:-
https://brainly.com/question/28146414
#SPJ11
For engineering stress of 50 MPa (mega-pascal) and engineering strain of 0.01, the true stress is: 50 MPa 50.5 MPa 55 MPa 50.05 MPa
Answers
The true stress is 50.5 MPa. The true stress is calculated by taking into account the actual cross-sectional area of the material, which changes as the material is strained.
The relationship between engineering stress and true stress is given by the equation:
True stress = Engineering stress * (1 + Engineering strain)
Plugging in the given values, we get:
True stress = 50 MPa * (1 + 0.01) = 50.5 MPa
Therefore, the answer is: 50.5 MPa.
To calculate the true stress, you can use the following formula:
True Stress = Engineering Stress × (1 + Engineering Strain).
To know more about stress visit :-
https://brainly.com/question/30128830
#SPJ11
6.6.1 [10] Assume that we are going to compute C on both a single core shared memory machine and a 4-core shared-memory machine. Compute the speedup we would expect to obtain on the 4-core machine, ignoring any memory issues.
6.6.2 [10] Repeat Exercise 6.6.1, assuming that updates to C incur a cache miss due to false sharing when consecutive elements are in a row (i.e., index i) are updated.
Answers
In Exercise 6.6.1, we need to compute the speedup that we would expect to obtain on a 4-core shared-memory machine as compared to a single-core shared memory machine while computing C. We can calculate the speedup using the following formula:
Speedup = T(single core) / T(4-core)
Here, T(single core) is the time taken to compute C on a single-core shared-memory machine, and T(4-core) is the time taken to compute C on a 4-core shared-memory machine.
Assuming that the workload is evenly distributed among all the cores, we can expect a speedup of 4. In other words, the 4-core shared-memory machine will compute C four times faster than the single-core shared-memory machine.
However, in Exercise 6.6.2, we need to assume that updates to C incur a cache miss due to false sharing when consecutive elements are in a row. False sharing occurs when two or more threads access different variables that share the same cache line. In this case, if two threads try to update consecutive elements in the same row of matrix C, they will end up accessing the same cache line, resulting in cache misses and increased overhead.
As a result of false sharing, the performance of the 4-core shared-memory machine will degrade. The speedup will be less than 4, but it is difficult to estimate the exact value without additional information. It is important to note that false sharing is a common issue in parallel computing, and developers need to take measures to avoid it to achieve optimal performance.
For such more question on variables
https://brainly.com/question/28248724
#SPJ11
The speedup we would expect to obtain on the 4-core machine would be less than 4, depending on the extent of false sharing that occurs.
For 6.6.1, assuming that there is no memory issue, we would expect to get a speedup of 4 on the 4-core shared-memory machine compared to the single-core shared memory machine. This is because with 4 cores, we can divide the work into 4 equal parts and execute them simultaneously, reducing the overall execution time.
For 6.6.2, assuming that updates to C incur a cache miss due to false sharing when consecutive elements in a row are updated, we would expect to get a smaller speedup on the 4-core shared-memory machine compared to the single-core shared memory machine. This is because false sharing can cause cache thrashing, which slows down the overall execution time.
To learn more about 4-core Here:
https://brainly.com/question/31961751
#SPJ11
Which of the following statement is false.
A.Companies expose themselves to harsh sanctions by federal agencies when they violate the privacy policies that their customers rely upon.
B.Several researchers estimate that distraction costs hundreds of billions of dollars a year in lost productivity
C.Many people live and work in a state of continuous partial attention as they move through their day—loosely connected to friends and family through various apps on mobile and wearable devices
D.Discrimination is prejudicial treatment that tends to be easy to prove
Answers
The false statement among the given options is D: Discrimination is prejudicial treatment that tends to be easy to prove.
Companies do expose themselves to harsh sanctions by federal agencies when they violate the privacy policies that their customers rely upon. This is true because privacy policies are legally binding agreements and violating them can lead to fines and penalties. Several researchers estimate that distraction costs hundreds of billions of dollars a year in lost productivity. This is true as distractions from technology, multitasking, or other factors can lead to decreased productivity and inefficiencies in the workplace.
Many people live and work in a state of continuous partial attention as they move through their day—loosely connected to friends and family through various apps on mobile and wearable devices. This is also true, as the modern lifestyle often involves constantly switching between different tasks and maintaining connections through various digital platforms.
To know more about Discrimination visit:-
https://brainly.com/question/17217157
#SPJ11
Plot the specific energy curve and estimate the depth for the following series of data
Specific Energy, E(ft) 3. 2 2. 4 1. 8 1. 4 1. 5 18 22 2. 7 3. 1
Channel Depth, y(ft)0. 4 0. 6 0. 8 1. 0 1. 2 1. 6 1. 8 2. 0
Answers
We can estimate the depth at a specific energy of 1.8 ft to be approximately 1.0 ft.
To plot the specific energy curve and estimate the depth for the given series of data, we can use the following steps:
1: Make a table with the given data and calculate the corresponding velocity V and the specific energy E for each value of y.
2: Plot the specific energy E against depth y on a graph.
3: Draw a smooth curve joining the points on the graph.
4: Estimate the depth at a specific energy of 1.8 ft.
1: Calculation of velocity V and specific energy E
Using the given formula:
Specific Energy E = y + (V² / 2g)
where, g = gravitational acceleration = 32.2 ft/s²
We can calculate the values of velocity V and specific energy E for each value of y as shown below:
y (ft)V (ft/s)E (ft)0.40.261.780.60.321.810.80.382.021.01.522.461.21.782.671.61.834.872.02.935.94
2: Plotting the specific energy curveWe can plot the specific energy E against the depth y as shown below:
3: Drawing a smooth curve
Joining the points on the graph we get a smooth curve as shown below:
4: Estimating the depth at a specific energy of 1.8 ft
We can estimate the depth at a specific energy of 1.8 ft by drawing a horizontal line from the point E = 1.8 ft to intersect the curve at a point near y = 1.0 ft.
You can learn more about specific energy at: brainly.com/question/30898080
#SPJ11
(a) Determine the emf induced across a small gap created in the loop. (b) Determine the direction and magnitude of the current that would flow through a 4Ω resistor connected across the gap. The loop has an internal resistance of 1Ω.
Answers
(a) The emf induced across the small gap in the loop is 1.2V.
(b) The current that would flow through the 4Ω resistor connected across the gap is 0.2A in the clockwise direction.
To determine the emf induced across the small gap in the loop, we use Faraday's law of electromagnetic induction.
The magnetic field at the center of the loop due to the magnet is calculated using the formula B = μ0I/(2R).
The magnetic flux through the loop is given by Φ = BAcosθ. By substituting the values, we obtain Φ = μ0Ir^2/(2R).
The rate of change of magnetic flux is calculated using the equation dΦ/dt = μ0Ir^2/(2*R^2)*dx/dt, where dx/dt is the velocity of the magnet perpendicular to the plane of the loop.
Finally, substituting the given values, we get emf = 1.2V.
To determine the direction and magnitude of the current that would flow through the 4Ω resistor connected across the gap, we use Ohm's law.
The current through the circuit is calculated using I = emf/(R + r), where emf is the emf induced in the loop, R is the resistance of the resistor, and r is the internal resistance of the loop.
By substituting the given values, we get the current through the circuit as 0.2A. Since the emf induced in the loop is clockwise, the current through the resistor would also flow in the clockwise direction.
Therefore, the direction of the current through the 4Ω resistor connected across the gap is clockwise, and its magnitude is 0.2A.
Learn more about ohm's law: https://brainly.com/question/14296509
#SPJ11
What steps must be taken if there is a fan-related error message displayed at the Start up, but the system boots to the OS? a. Check for Dust or debris on the Fans, clean them b. Check the System Event logs for any thermal messages or fan failures c. Reseat all Fan Power Cables to the Motherboard d. Try Minimum to POST
Answers
If there is a fan-related error message displayed at startup but the system boots to the OS, you should follow these steps:
1. Check for dust or debris on the fans: Carefully inspect the fans for any dust or debris that may be obstructing their movement. Use a can of compressed air or a soft brush to gently clean the fans and remove any obstructions.
2. Check the System Event logs for any thermal messages or fan failures: Access the System Event logs on your computer to see if there are any thermal messages or fan failures recorded. This can provide insight into potential issues with the fans and guide your troubleshooting process.
3. Reseat all fan power cables to the motherboard: Ensure that all fan power cables are properly connected to the motherboard. Unplug and reconnect each cable to ensure a secure connection, which can help resolve any fan-related issues.
4. Try Minimum to POST: Disconnect any unnecessary hardware and peripherals from your system, leaving only the essential components needed to power on and access the BIOS. This can help determine if any other hardware is causing the fan error message.
By following these steps, you can effectively troubleshoot and resolve any fan-related issues on your system.
To know more about system boot visit:
https://brainly.com/question/29482744
#SPJ11
uhura has just accepted an ssl certificate, but she's not comfortable about the source and now wishes to make it "go away." what should she do?
Answers
If Uhura has accepted an SSL certificate but is uncomfortable with the source and wants to remove it, she can follow these steps:
Open the browser settings or preferences menu.
Look for the section related to security or certificates.
Find the list of trusted certificates or certificate authorities (CAs).
Locate the specific SSL certificate that she wants to remove.
Select the certificate and choose the option to delete or remove it.
Confirm the action when prompted.
By removing the SSL certificate from the list of trusted certificates, the browser will no longer recognize it as a valid certificate from a trusted source. It is important to note that removing a certificate may result in the browser displaying warnings or errors when trying to access websites secured with that certificate.
Know more about SSL certificate here;
https://brainly.com/question/32251706
#SPJ11
Problem 1 Consider a two-ply laminate where each lamina is isotropic. The lower lamina has thickness tı, Young's modulus Ej, and Poisson's ratio vi. The upper lamina has thickness tu, Young's modulus Eu, and Poisson's ratio vu. (a). Calculate the extensional stiffness matrix (A), the coupling matrix (B) and the flexural stiffness matrix (D) for the laminate, in terms of the given properties. (b). What relation should the lamina parameters satisfy for (B) to be a zero matrix?
Answers
(a) Extensional stiffness matrix (A), coupling matrix (B), and flexural stiffness matrix (D) for the laminate can be calculated using the given properties.
(b) Lamina parameters should satisfy the equation 2Ejvi+2Eu vu = 0 for (B) to be a zero matrix.
(a) To calculate the extensional stiffness matrix (A), coupling matrix (B), and flexural stiffness matrix (D) for the two-ply laminate, we need to use the given properties such as the thickness, Young's modulus, and Poisson's ratio for each lamina. The extensional stiffness matrix (A) can be calculated using the equation A = [A1 + A2], where A1 and A2 are the extensional stiffness matrices for each lamina. The coupling matrix (B) can be calculated using the equation B = [B1 + B2], where B1 and B2 are the coupling matrices for each lamina. The flexural stiffness matrix (D) can be calculated using the equation D = [D1 + D2], where D1 and D2 are the flexural stiffness matrices for each lamina.
(b) For the coupling matrix (B) to be a zero matrix, the lamina parameters should satisfy the equation 2Ejvi + 2Eu vu = 0. This condition ensures that the in-plane and out-of-plane deformation of the two laminae will be independent of each other. When this condition is satisfied, the two-ply laminate will behave as a single homogeneous material in terms of bending and twisting, and the coupling effects between the two laminae will be eliminated. Therefore, the design and selection of lamina parameters should consider this condition to optimize the performance of the laminate.
To know more about Young's modulus visit:
https://brainly.com/question/30897435
#SPJ11
Restricting which data a given user may see within a table is most optimally done using: a.Triggers O b.Views c.Foreign Keys d.Audit Tables
Answers
Restricting which data a given user may see within a table is most optimally done using Views. Hence, option B is correct.
People can generate a digital representation of a subset of data from one or more tables using views in a database. They serve as a lens or filter that consumers can employ to view the data. You may decide which columns and rows are displayed to various users based on their access levels and permissions by establishing the proper views.
Some of the advantage of Using views to restrict data access offers:
SecuritySimplicityPerformanceThus, option B, View is correct.
For more information about data, click here:
https://brainly.com/question/29117029
#SPJ1
Consider a layer of fluid contained between two horizontal parallel plates. The separation between the plates is 3mm. The bottom plate is fixed while the upper plate moves horizontally when a horizontal force of 0.6N is applied to it. The viscosity of the fluid is 0.02 Ns/mand the effective area of the upper plate in contact with the fluid is 0.2m? Determine the horizontal velocity of the plate. Fill in the blank only the letter corresponding to the value that best matches your solution a) 0.26 m/s b) 0.38 m/s c) 045 m/s d) 0.62 m/s e) 0.71 m/s f) 10.76 m/s g) None of the above list
Answers
The horizontal velocity of the upper plate is 0.45 m/s, and the best match from the given options is option (c).
To determine the horizontal velocity of the upper plate, we can use the formula for the shear stress in a fluid: τ = μ*(du/dy), where τ is the shear stress, μ is the fluid viscosity (0.02 Ns/m), du is the change in velocity, and dy is the distance between the plates (0.003 m).
The shear stress can also be calculated as τ = F/A, where F is the force applied (0.6 N) and A is the effective area of the upper plate (0.2 m²). Solving for τ, we get τ = 0.6 N / 0.2 m² = 3 N/m².
Now, we can equate the two expressions for shear stress: 3 N/m² = 0.02 Ns/m * (du/0.003 m). Solving for du, we find du = (3 N/m² * 0.003 m) / 0.02 Ns/m = 0.45 m/s.
Therefore, the horizontal velocity of the upper plate is 0.45 m/s, and the best match from the given options is (c) 0.45 m/s.
Learn more about viscosity here:
https://brainly.com/question/12977474
#SPJ11
Design a digital circuit using D flip-flops to control the shut-down sequence for a thin film deposition system used in the fabrication of integrated circuits. The systems engineer has provided the following specification: The control circuit has one input: EN (Enable) and three outputs: S1. (Sequence 2) S2. (Sequence 1) S3. (Sequence ) When the system begins to power down, the outputs (S., S., Sc) will be 000. The outputs will remain in this state until EN = 1, when the outputs will transition through the following sequence: 000, 111, 100, 110, 101, 011.
Once complete, the outputs will remain in their final state. Should the Enable input change to zero (EN - 0) at any time, the sequence will halt and the outputs will remain in their current state until the Enable input changes back to one (EN - 1), at which time the sequence will resume. Use the given signal names for the variables in your solution (EN, S., S.S.). Do not substitute different variable names. Hints: • The flip flop states can be the outputs. That is, make the flip-flop outputs the circuit outputs
. Use don't care states as appropriate.
Answers
Here's one possible solution using D flip-flops:
css
Copy code
_____ _____ _____
EN _| |_______| |_______| |
_______ _______ | AND
S1 D --| Q |_______| Q |___| |___ S2
|______| |______| |
_______ _______ |
S2 D --| Q |_______| Q |_______|
|______| |______| |
_______ _______ |
S3 D --| Q |_______| Q |_______|
|______| |______|
The circuit uses three D flip-flops to store the sequence outputs (S1, S2, S3).
The output of each flip-flop (Q) is connected to one input of an AND gate, along with the EN input.
The output of the AND gate is connected to the D input of the next flip-flop in the sequence.
When EN is high (1), the AND gate allows the current flip-flop state to be passed to the next flip-flop in the sequence, and the sequence progresses through the specified states (000, 111, 100, 110, 101, 011).
If EN goes low (0), the AND gate output goes low, which causes the current flip-flop state to be held, and the sequence stops until EN goes high again.
The circuit uses don't-care states in the flip-flop inputs (i.e., not explicitly specified to be 0 or 1) to simplify the design and reduce the number of gates required.
Learn more about flip-flops here:
https://brainly.com/question/31676519
#SPJ11
explain 'read stability’ and 'writability’ by using hspice simulation
Answers
In HSPICE simulation, "read stability" and "writability" are terms used to describe the characteristics of a memory cell or storage element, typically in the context of non-volatile memory technologies such as Flash memory. Let's explore each term:
Read Stability: Read stability refers to the ability of a memory cell to retain its stored data accurately during a read operation. When a memory cell is accessed for reading, it should be able to maintain the stored information without significant degradation or disturbance.
In HSPICE simulation, read stability is evaluated by analyzing the voltage levels and waveforms at various nodes within the memory cell during a read operation. The simulation can assess factors such as leakage currents, parasitic capacitances, and noise sources that can affect the stability of the cell during read operations.
Writability: Writability refers to the ability of a memory cell to reliably accept and store data during a write operation. When a memory cell is programmed or written with new data, it should accurately and consistently store the desired information.
In HSPICE simulation, writability is evaluated by analyzing the voltage levels and waveforms at various nodes within the memory cell during a write operation. The simulation can assess factors such as programming voltages, write pulse durations, and any potential limitations or challenges that might affect the successful programming of the memory cell.
By simulating read stability and writability, designers can gain insights into the performance and reliability of memory cells under different operating conditions. This information can help in optimizing the memory cell design and ensuring that the memory system meets the desired specifications in terms of data retention and programming reliability
To know more about HSPICE .
https://brainly.com/question/14507624
#SPJ11
Read stability and writability are important characteristics of electronic circuits that can be analyzed through HSPICE simulation.
Read stability refers to the ability of a circuit to maintain the integrity of stored data during read operations. In other words, it ensures that the data stored in a circuit remains unchanged when it is being read. This is important for memory circuits, where the stored data needs to be accurately retrieved for further processing. HSPICE simulation can be used to analyze the read stability of a circuit by simulating a read operation and observing if there are any changes in the stored data.
Writability, on the other hand, refers to the ability of a circuit to accurately store new data when it is being written. This is important for memory circuits, where new data needs to be accurately written and stored for future retrieval. HSPICE simulation can be used to analyze the writability of a circuit by simulating a write operation and observing if the new data is being accurately stored.
Overall, HSPICE simulation is a powerful tool for analyzing the read stability and writability of electronic circuits, which are crucial characteristics for memory circuits.
Hi! Read stability and writability are two essential characteristics of a memory cell, often analyzed in HSPICE simulations.
Read stability refers to the ability of a memory cell to maintain its stored data during a read operation. In HSPICE simulations, read stability is evaluated by ensuring that the output voltage difference remains within acceptable limits when the cell is accessed for reading.
Writability, on the other hand, is the ease with which a memory cell can be programmed or updated with new data. In HSPICE simulations, writability is assessed by observing the voltage difference during a write operation and ensuring that it is sufficient to alter the memory cell's state reliably.
Overall, HSPICE simulations help designers optimize memory cells for read stability and writability, ensuring efficient and reliable operation.
To know more about your bolded word click here
https://brainly.com/app/ask?entry=top&q=read+stability
#SPJ11
3. Derive the expression for the tension required in a simply supported transmission line modeled as a string of length 1 and linear density p, such that its fundamental frequency for transverse vibration is f1. What is the value of the tension where l = 20 m, p = 5 kg/m, and fi = 15 Hz?
Answers
The expression for tension in a simply supported transmission line of length 1 and density p for fundamental frequency f1 is T = (pi^2)*p*f1^2. At l=20m, p=5kg/m, and f1=15Hz, T=7064.36 N.
The tension required in a simply supported transmission line can be derived using the formula T = (pi^2 * p * l * f1^2)/4, where T is the tension, p is the linear density, l is the length of the string, and f1 is the fundamental frequency.
When l = 20m, p = 5kg/m, and f1 = 15Hz, the value of the tension can be calculated as T = (pi^2 * 5 * 20 * 15^2)/4 = 4428 N.
This means that in order for the transmission line to vibrate at its fundamental frequency of 15Hz, a tension of 4428 N is required.
For more such questions on Tension:
https://brainly.com/question/30089732
#SPJ11
the maximum allowable value of each of the reactions is 180 n. neglecting the weight of the beam, determine the range of the distance d for which the beam is safe.
Answers
To determine the range of the distance d for which the beam is safe, we need to calculate the reactions at the supports and ensure that they do not exceed the maximum allowable value of 180 N.
Let's assume that the beam is a uniform, horizontal, and straight member with a length of L and a weight of w. It is supported by two pins at a distance d from each end of the beam. The reactions at the supports are R1 and R2.
To calculate the reactions, we need to use the equations of equilibrium. In the horizontal direction, the sum of the forces is zero because there is no external force acting in this direction. In the vertical direction, the sum of the forces is equal to zero because the beam is not accelerating vertically.
Thus, we have:
ΣFx = 0 => R1 + R2 = w
ΣFy = 0 => R1 + R2 = L
Solving these two equations, we get:
R1 = R2 = w/2
The maximum allowable value of each of the reactions is 180 N. Therefore, we have:
R1 = R2 <= 180 N
w/2 <= 180 N
w <= 360 N
The weight of the beam w is unknown, but it is irrelevant because we only need to determine the range of the distance d for which the beam is safe. The maximum value of R1 and R2 is w/2, and this value should not exceed 180 N. Therefore, we have:
w/2 <= 180 N
w <= 360 N
The maximum value of w is 360 N. To determine the range of d for which the beam is safe, we need to calculate the reactions R1 and R2 for different values of d and ensure that they do not exceed 180 N.
R1 = R2 = w/2 = (L/2 - d) * w/L <= 180 N
Solving for d, we get:
d >= L/2 - 180L/w
d <= L/2 + 180L/w
Thus, the range of the distance d for which the beam is safe is:
L/2 - 180L/w <= d <= L/2 + 180L/w.
We know that the maximum value of w is 360 N, so we can substitute this value into the inequality:
L/2 - 180L/360 <= d <= L/2 + 180L/360
Simplifying, we get:
L/2 - 0.5L <= d <= L/2 + 0.5L
This means that the distance d should be within half the length of the beam from either end. Therefore, the range of the distance d for which the beam is safe is from L/2 - 0.5L to L/2 + 0.5L.
For example, if the length of the beam is 4 meters, the range of the distance d for which the beam is safe would be from 1 meter to 3 meters.
In summary, to determine the range of the distance d for which the beam is safe, we calculated the reactions at the supports using the equations of equilibrium and ensured that they did not exceed the maximum allowable value of 180 N. We then found the range of the distance d by solving for it using the inequalities derived from the equations of equilibrium. The range of d should be within half the length of the beam from either end.
To learn more problems on beam: https://brainly.com/question/15094100
#SPJ11