A 2400 kg car traveling to the north is
slowed down uniformly from an initial velocity
of 21.0 m/s by a 7110 N braking force acting
opposite the car's motion.
a) What is the car's velocity after 2.00 s?
Answer in units of m/s.

They are attractive forces between two permanent dipoles, or two induced dipoles.

A dipole is a type of electrical charge consisting of two equal and oppositely charged poles, or points of charge. The two poles are usually represented by a positive and negative sign. Dipoles are commonly found in molecules, atoms, and other types of particles, and are responsible for many of the physical and chemical interactions we observe in nature. Dipoles can also be created artificially with electrical equipment, such as in the case of an electric dipole antenna, which is used to transmit or receive radio signals. In a dipole, the two charges attract each other, which creates a field of force between them. The strength of this field depends on the distance between the two charges. Dipoles also exist in a magnetic form, in which the two poles have opposite magnetic poles and create a magnetic field.

This type of intermolecular force is a type of Van der Waals force and is much stronger than the London dispersion forces. They are responsible for most of the physical properties of polar substances, such as boiling points, melting points, and solubility.

To learn more about dipoles
https://brainly.com/question/14553213
#SPJ4

When reggie stepped up to the plate and hit a 0. 150-kg fast ball traveling at 36. 0 m/s, the impact caused the ball to leave his bat with a velocity of 45. 0 m/s in the opposite direction. If the impact lasted for 0. 002 s, the force did reggie exert on the baseball is 6075 N.

The force can be calculate as follows:

assuming that the ultimate direction of motion is positive and the starting direction of motion before to impact is negative.

m = 0.15 kg, or the mass of the ball being struck

v0 is the ball's pre-impact initial velocity and is equal to 36 m/s.

45 m/s is the ball's final speed after impact, or v.

Time of Impact: 0.0020 seconds

Reggie's force on the ball was F.

Incorporating impulse-change into the momentum equation

F t = m (v - v₀)

F (0.0020) = (0.15) (45 - (- 36))

F = 6075 N

Learn more about force at https://brainly.com/question/13976717

#SPJ4

The moment caused by the 2 kg mass placed at a distance of 0.5 m to the left of the pivot is 1 kg m. This moment is anticlockwise.

Moment is a physical parameter equal to the product of the distance or displacement and another physical quantity such as mass, force etc.

For a mass of 2 kg and distance of 0.5 m the moment is  :

moment = mass × distance

= 2 × 0.5 = 1 kg m

If we are taking the moment of force, then it the product of the distance and force acting on the body is taken.

force = mg

F =  2 kg × 9.8 m/s² = 19.6 N

then moment of force = 19.6 N × 0.5 m = 9.8 N

The moment from left to right in direction is anticlockwise.

Find more on moment:

https://brainly.com/question/16755013

#SPJ1

Answer:

Bbbbbbbbbbbbbb. bbbbbbbbbbbbbbb

The properties of water that makes it possible for life to continue to exist in lakes covered by a thick layer of ice for many months of the year are:

The correct option is C.

The water in frozen lakes supports life because of the following properties f water;

As soon as the water turns to ice, the ice loses a lot of its water-like density and continues to float on the lake's surface. Water loses density when it grows colder below 4° Celsius, forcing water that is about to freeze to float to the top.

Learn more about water at: https://brainly.com/question/26846829

#SPJ1

The answers include the following below:

This is referred to as the propagation of disturbances from place to place in a regular and organized way and there are different types of waves.

An example is the longitudinal wave which has the vibration of the particles takes place in the same direction as that of the wave.

Read more about Wave here https://brainly.com/question/25699025

#SPJ1

Answer:

is d

Explanation:

Alternative energy sources like solar and wind power are always available option A is the correct answer.

In addition to the seven energy sources mentioned above, other alternative energy sources include geothermal energy, wave energy, hydroelectric energy, solar thermal energy, and even space solar energy. Geothermal energy is generated within the earth and is used, unlike wave and hydroelectric energy uses the power of water.

There will never be a shortage or shortage of solar energy because it is one of the cleanest and most plentiful renewable resources. Every person on the planet might theoretically have access to energy for a year with just one hour of sunlight shining on the earth's atmosphere.

To know more about Alternate energy visit

brainly.com/question/3758506

#SPJ4

Force and weight are related in that weight is a type of force. Specifically, weight is the force exerted on an object due to gravity. It is measured in units of force, such as newtons (N) or pounds (lb).

Weight is a scalar quantity, which means it has magnitude but no direction. It is determined by the mass of an object and the acceleration due to gravity.

The formula for weight is:

Weight = mass x gravity (W=mg)

On the other hand, Force is a vector quantity, which means it has both magnitude and direction. Force can be described as the push or pull on an object. It can be due to a variety of causes, such as friction, tension, or pressure. It is also measured in units of force, such as newtons (N) or pounds (lb).

So, to relate force and weight, weight is a force that acts on an object due to gravity, whereas force can be any kind of push or pull on an object, and weight is one of them.

To conclude, weight is a force that is exerted on an object due to gravity, while force is a more general term that can refer to any type of push or pull on an object. The key difference between the two is that weight is a scalar quantity while force is a vector quantity.

Hope This Helps You!

When the object reaches the terminal velocity the object stops accelerating. Option B

The greater the objects surface area, the more air resistance it encounters. Option A

Terminal velocity is the maximum velocity an object reaches when falling through a fluid, such as air, due to the balance of gravitational force and fluid drag.

Surface area affects terminal velocity because a larger surface area results in greater fluid drag force, which slows the object's descent. A smaller surface area results in less fluid drag and a higher terminal velocity.

Learn more about terminal velocity:https://brainly.com/question/2654450

#SPJ1

Answer:

An eclipse of the sun must occur at a "new" moon - when the moon is between the earth and the sun.

The word penumbra refers to a "partial" eclipse as opposed to umbra which refers to total eclipse.

A partial eclipse must include both terms - "new" and "penumbra"

The image is inverted, the lens is converging, the image is enlarged in size, the focal length of the lens with the greater index of refraction(lens 1) will be smaller than that of the other lens(lens 2).

A real image is that which can be obtained on the screen whereas a virtual image cannot be. A concave lens always produces virtual image whereas a convex lens can produce both real and virtual image. So the lens is convex lens which is also called converging lens. A converging lens always produces enlarged or the same size image but never produce smaller image. So the image will be enlarged in size.

The refractive index of a glass is the measure of light bending ability of it. Greater the refractive index more will be the bending of a light ray. So, if two convex lenses identical in size and shape are manufactured from glass with two different indices of refraction, the focal length of the lens with greater refractive index would be smaller.

To know more about focal length, here

https://brainly.com/question/29870264

#SPJ4

Answer :

after this all u can write this

The steps to achieve a work-life balance, one should manage their time well, establish limits, pay attention to their health, and enjoy their work.

The state of equilibrium where a person equally priorities the responsibilities of their career and their personal life is known as work-life balance. Because both are significant, neither should be ignored. Common causes of a bad work-life balance include the following: expanded obligations at work. putting in more hours.

An ACAS analysis on work-life balance and flexible working shown how a poor balance can cause absences, poor productivity, and stress. Strict regulations, an excessive workload, a hostile work environment, deadline pressure, and a lack of job security are some organisational variables that interfere with work-life balance.

Learn more about work-life balance here:

brainly.com/question/6842966

#SPJ1

According to the question, the answer of the given convert will be: 1.5 days = 36 hours, 5.2 ft = 1.58 m, 3600 s = 1 hr,10.2 m = 33.46 ft, 305 g = 0.305 kg, 180 pm = 0.18 m, 73 kg = 73000 g, 1,366 s = 22.77 min, 86,000 m = 86 km.

What is convert?

Convert is a term used to describe the process of changing one type of data into another. This could include changing a file format, changing a text document into a spreadsheet, or converting a physical document into a digital file. It is a useful tool in many industries and is often used to make sure that data is stored in a standard format, making it easy to access and use. Convert is used in a variety of settings, including media, accounting, and business. It is also used to help ensure data security and accuracy.

To learn more about convert visit:

brainly.com/question/29217523

#SPJ1

The number of revolutions  of the tire during the motion is 10 revolutions.

The number of revolutions  of the tire during the motion is calculated from the distance travelled by the tire.

The total distance travelled by the tire during the motion is calculated as follows;

s = t ( u + v ) / 2

where;

s = 3.7 x ( 13.9 + 0 ) / 2

s = 25.72 m

The number of revolutions of the tire is calculated as follows;

N ( 2πr ) = 25.71

where;

N = ( 25.71 ) / ( 2π x 0.4255 )

N = 9.6 ≈ 10 rev

Learn more about number of revolutions here: https://brainly.com/question/20700248

#SPJ1

The resistance would increase when the charge density increases.

We have to note that when we talk about the resistance, we mean the opposition that is offered to the flow of current in the circuit. Let it be known that the resistance would be seen to increase as the charge density is increasing. The reason why this is going to occur is that we are going to have a lot of charges that are migrating at the same time and as such the rate of the movement of the charges or their speed would be slowed down.

If on the other hand, we see that the charge density is low, we are going to have less charges and they are going to move more freely and the resistance or the opposition to the movement of the charges would be lower.

Learn more about resistance:https://brainly.com/question/11431009

#SPJ1

The energy transformed from the water in the kettle to the surrounding water loses 4200 J/kg °C * 0.5 kg = 2100 J/°C.

As it's lost 46,200 J in total (regardless of the time it took for this to happen), it must have reduced in temperature by 22 degrees. Assuming 100°C initially, temperature of water in kettle is now 78°C.

The purpose of this experiment is to determine the specific heat of two metal blocks. In one of these measurements you will also investigate the use of Newton's Law of Cooling to calculate a cooling correction. The units of specific heat in SI are J / kg ˚C.

When a body of mass M at temperature T1  receives an amount of heat (or energy) Q, its temperature may increase from T1 to T2. The heat capacity C of a body is the amount of heat required to raise its temperature by one (Kelvin) degree.

To know more about energy transformed here

https://brainly.com/question/26547865

#SPJ4

The planetesimals, which are small bodies that eventually formed into larger objects such as planets, are believed to have formed last in our solar system.

Our solar system formed around 4.6 billion years ago from a cloud of gas and dust, known as the solar nebula. The sun formed first from the dense, hot center of the nebula. As the sun formed, it began to emit heat and radiation, which caused the remaining gas and dust to begin to condense and form into small objects known as planetesimals.

As these planetesimals collided and merged, they grew larger and larger, eventually forming the inner planets, such as Mercury, Venus, Earth, and Mars. The outer planets, such as Jupiter and Saturn, also formed from the collision and merger of planetesimals, but they formed later in the process.

To learn more about planetesimals visit: https://brainly.com/question/10337322

#SPJ4

Your question seems incomplete, but I assume the question was:

"Which object(s) formed last in our solar system?

the sun

the solar nebula

the inner planets

the planetesimals."

Answer:

The ratio of the mass of planet Zeb to the mass of Earth must be 8.

Explanation:

The gravitational acceleration on the surface of a planet is determined by the mass of the planet and its radius. The equation is g = GM/r^2, where G is the gravitational constant, M is the mass of the planet, and r is the radius of the planet.

If we assume that the gravitational acceleration on the surface of both planets is the same, we can set the equation for Earth equal to the equation for planet Zeb and solve for the ratio of the mass of planet Zeb to the mass of Earth.

g(earth) = GM(earth)/r(earth)^2 = GM(zeb)/r(zeb)^2

We know that r(zeb) = 2 * r(earth)

so,

GM(earth)/r(earth)^2 = GM(zeb)/(2*r(earth))^2

GM(zeb)/GM(earth) = (2*r(earth))^2 /r(earth)^2

GM(zeb)/GM(earth) = 4*4

GM(zeb)/GM(earth) = 16

So the ratio of the mass of planet Zeb to the mass of Earth is 16/1 = 8

Pyramid collision, recommendations are made specifically for each person depending on their age, gender, and amount of physical activity. The consumption of cereals,  milk, veggies, fruit, and oils are the main.

A health impact pyramid: what is it?

The Health Benefit Pyramid is a diagram that shows the many levels of impact that can come from interventions in public health. Attempts to deal with the social determinants that potentially affect your health are at the bottom of the pyramid, suggesting interventions with the highest potential impact. Housing, financial stability, public safety, jobs, education, and the environment are a few examples of these. The broader determinants of health are these.

What are the four primary categories of factors that affect health?

Numerous variables affect health, including These circumstances are referred to as social determinants, which are the socioeconomic factors that influence life expectancy and quality of life and support health. Examples of these factors include accommodation, education, access to food, and transportation. Too frequently, people lack control over their ability to access these resources that influence their health.

To know more about collision visit :

brainly.com/question/4322828

#SPJ1

The outer diameter of a hollow steel tube when the stress is limited to 120 MN/m² is  119.35 mm

Axial stress refers to the stress induced in a loaded member along the longitudinal or axial member direction. Calculated mathematically from the ratio of the axial or longitudinal force to the cross-sectional area of ​​the member.

Using the expressions for the axial stress and rated load, the cross-sectional area of ​​the tube can be determined. Substituting the values ​​for the cross-sectional area of ​​the tube and the inside diameter of the tube in the expression for the cross-sectional area of ​​a hollow cylinder yields the outside diameter of the tube.

                                σ = F/A

The formula for calculating the cross-sectional area of ​​a hollow cylinder.

A = π/4(D² – d²)

Here, the inside and outside diameters of a hollow cylinder are d and D.

Step 1

Determine the cross-sectional area of ​​tube (A) using the axial stress expression:

σ = F/A

Here, the axial stress limit is σ = 120 MN/m2 and the tensile load is F = 400 kN

σ = F/A

120 x 10³KN/1 MN = 400 kN/A

A = (400 kN) ÷ (120 x 10³ kN/m²)

A = 3333.33 mm²

Substitute the values ​​for the cross-sectional area of ​​the cylinder and the inside diameter of the cylinder in the equation for the cross-sectional area of ​​the hollow cylinder to calculate the outside diameter of the cylinder.

A = 3333.33 mm²

d = 100 mm

A = π/4(D² – d²)

3333.33 mm² = π/4(D² – 100²)

D² =[tex]\sqrt{ 14244.128}[/tex]

D = 119.35 mm

So, the outside diameter of the hollow is 119.35 mm.

Complete the questions is:

A hollow steel tube with an inside diameter of 100 millimeters must carry a tensile load of 400 kN. What is the outside diameter of the tube if the stress is limited to 120 MN/m²?

Learn more about the axial stress at https://brainly.com/question/7013119

#SPJ4

A balloon absorbs electrons from a wool fabric when it is rubbed against it, leaving the balloon with a negative charge and the wool with a positive charge.

Electrons from the atoms and molecules in your hair migrate to the balloon when you brush it against your head. The balloon acquires a negative charge thanks to the negative charge of electrons, but your hair retains a positive charge.

Electrons migrate from the hair or wool to the balloon when the balloon is rubbed against it. The balloon picks up a net negative charge because electrons have a negative charge. The can rolls because the positive charges in the can are drawn to the negative charges in the balloon.

learn more about static electricity refer

https://brainly.com/question/18562731

#SPJ1

Answer:

1.Benefits of Renewable Energy Use

Less global warming.

Improved public health.

Inexhaustible energy.

Jobs and other economic benefits.

Stable energy prices.

2.Hydroelectric generation at scale dates back more than a century, and is still our largest renewable source – excluding traditional biomass, it still accounts for more than 60% of renewable generation

3.Biomass can be burned to create heat (direct), converted into electricity (direct), or processed into biofuel (indirect). Biomass can be burned by thermal conversion and used for energy

According to the NEC, a class 1 power limited circuit must be supplied from a source having a rated output of not more than 30 volts and 1000 volt-amperes.

NEC stands for National Electrical Code. It is a part of National Fire Protection Association (NFPA) of united states. NEC provides the standard and code for the safe installation of electrical wiring and equipment.

Class 1 power limited has a device that controls or regulates the current from the power source. This device prevents the overflow of the current in the circuit and thereby also prevents the short circuiting, overload, ground fall, etc.

To know more about power, here

https://brainly.com/question/29575208

#SPJ4

Answer:

a

true

true

true

true

true

true

true

The BEST description of the effect that her body distortion is having is (C) depression.

Depression is a mental health disorder characterized by a persistent feeling of sadness, hopelessness, and loss of interest in activities. People with depression may experience changes in sleep, appetite, energy level, and concentration. Additionally, they may experience feelings of guilt, worthlessness, and helplessness. Symptoms of depression can range from mild to severe and can include physical symptoms such as fatigue, headaches, and stomachaches. Psychotherapy, medication, and dietary changes were available treatments for depression. With the right support and treatment, individuals can lead a healthy and fulfilling life.

To learn more about depression
https://brainly.com/question/10045613
#SPJ1

Answer: Cosmology

Explanation:

Conclusion statement defines the answer of a scientific problem based on the result of the experiment.

A scientific problem is solved by the scientific methods. A scientific method is the step-by-step approach to a conclusion of the problem. It may include the following steps.

Observation: It is the first step of the method. It is based on that how do you see the problem.

Hypothesis: It is the result you think that you will get.

Prediction: It is based on your scientific knowledge. If our hypothesis is correct than our prediction will also be true.

Experiment: It is the system or mechanism designed by you to test your hypothesis.

Conclusion: It is the final result based on the experiment of the method. This statement tells you whether your hypothesis is true or not.

To know more about Conclusion, here

https://brainly.com/question/78686  

#SPJ4