A 4.0 kg slides with an initial speed of 3.0m/s towards a spring on a frictionless horizontal surface. When the box hits the spring, the spring compresses by
0.30 m. What is the spring constant?

A 4.0 Kg Slides With An Initial Speed Of 3.0m/s Towards A Spring On A Frictionless Horizontal Surface.

Answers

Answer 1

The  spring constant is 400 N/m. For the given question.

What is spring constant ?

The spring constant (k) is a physical property of a spring, which represents the stiffness of the spring. It is defined as the force required to stretch or compress a spring by a certain amount (x) divided by that amount of deformation:

k = F/x

where F is the applied force and x is the displacement or deformation of the spring from its equilibrium position. The spring constant has units of force per unit of length, such as newtons per meter (N/m) in the SI system of units. A higher spring constant means that more force is required to deform the spring by the same amount, and the spring is considered to be stiffer. Conversely, a lower spring constant means that less force is required to deform the spring by the same amount, and the spring is considered to be more flexible.

We can use the conservation of energy to find the spring constant.

Initially, the box has kinetic energy given by:

K₁= (1/2)mv₁²

= (1/2)(4.0 kg)(3.0 m/s)²

= 18 J

At maximum compression, all of the kinetic energy is stored as potential energy in the spring. The potential energy stored in a spring is given by:

U = (1/2)kx²

where k is the spring constant and x is the displacement from the equilibrium position. In this case, x is the compression of the spring, which is 0.30 m.

So, the potential energy stored in the spring is:

U = (1/2)kx²

= (1/2)k(0.30 m)²

= 0.045k J

Since energy is conserved, we can equate the initial kinetic energy to the potential energy stored in the spring:

K₁= U

18 J = 0.045k J

k = 400 N/m

Therefore, the spring constant is 400 N/m.

To know more about springs visit :-

https://brainly.com/question/14670501

#SPJ1


Related Questions

what observations can you make if the string are released in the trolley

Answers

Without more specific details, it is difficult to determine exactly what observations might be made if strings are released in a trolley.

However, here are a few general possibilities:

If the strings are attached to objects or weights, releasing them may cause those objects to fall or move in some way. The motion of the objects could be observed.If the trolley is on a slope or incline, releasing the strings could cause the trolley to roll or slide down the slope. The speed and direction of the trolley's motion could be observed.If the strings are attached to other parts of the trolley itself, releasing them could cause some part of the trolley to move or shift. This could be observed visually or by measuring any changes in the trolley's position or orientation.

To know more about motion , visit :

https://brainly.com/question/22810476

#SPJ1

why big tractor can plough many fields than small tractor​

Answers

A big tractor is more efficient and productive than a small tractor, allowing it to plow through more fields and cover more ground with less time and effort.

A big tractor can plow many fields than a small tractor due to several reasons:

Engine Power: Big tractors have larger and more powerful engines than small tractors, which allow them to generate more torque and power to pull heavy loads and work for longer periods of time without overheating or breaking down. This means they can work more efficiently and cover more ground than small tractors.

Size and Weight: Big tractors are usually larger and heavier than small tractors, which gives them more stability and traction on the ground. This allows them to plow through tough and uneven terrain with less effort and more control, reducing the time and effort needed to complete the task.

Implements: Big tractors can accommodate larger and more advanced implements, such as wider plows, cultivators, and seeders, which allow them to cover more ground with each pass. These implements can also be customized to match the specific needs of the soil and crops, increasing the efficiency and productivity of the tractor.

Learn more about tractor at:

https://brainly.com/question/21603150

#SPJ1

Sam drives 20 miles North, 10 miles East, 20 miles South and 10 miles West.
Distance:
Displacement:

Answers

Sam traveled a total distance of 60 miles, but his displacement is zero, as he ended up back at his starting point after all of his movements.

How to measure the distance?

The distance that Sam has traveled is the total length of the path he took, regardless of the direction. In this case, the distance can be calculated as follows:

Distance = 20 miles (North) + 10 miles (East) + 20 miles (South) + 10 miles (West)

Distance = 60 miles

Therefore, Sam has traveled a total of 60 miles.

The displacement, on the other hand, is the shortest distance between the starting point and the ending point. It is the distance between the initial and final position of an object, measured in a straight line. To calculate the displacement, we need to find the net vector sum of all the individual movements.

Starting from the origin, Sam moved 20 miles to the north and then 20 miles to the south, which means he ended up back at the starting point. Next, he moved 10 miles to the east and then 10 miles to the west, which also means he ended up back at the starting point.

Therefore, the displacement of Sam's journey is zero.

In summary, Sam traveled a total distance of 60 miles, but his displacement is zero, as he ended up back at his starting point after all of his movements.

To know more about distance visit :-

https://brainly.com/question/26046491

#SPJ1

if the speed increase and wavelength stays the same what will happen to energy?

Answers

Answer:

If frequency is constant, wavelength will get longer as speed increases. Here is an animation of a wave changing speed. The green dots and line show that frequency is constant on both mediums, but the speed and wavelength both change.

I actually have 3 questions. >33

1. Write about a time when you felt very cold and did something to make yourself feel warm, or a time when you felt hot and did something to cool yourself down. What caused the heat to transfer from one place to another place? How did this transfer of heat cause a change in temperature?

2. Why is the temperature of the liquid in the flask on the previous page measured when the liquid in the thermometer has stopped rising?

3. How can the thermometer in the flask on the previous page be used to demonstrate the relationship between heat transfer and kinetic energy? Explain.

Answers

When you contact anything hot, the heat is transmitted from the object to your hand, making it feel hot. When you contact something cold, heat is transmitted from your hand to the object, making it feel chilly.

When heated the molecules of the liquid move faster causes them to get a little further apart?

when heated, the molecules of the liquid in the thermometer move faster, causing them to get a little further apart. this results in movement up the thermometer. when cooled, the molecules of the liquid in the thermometer move slower, causing them to get a little closer together.

When the liquid in the thermometer is heated, the molecules move quicker, forcing them to move wider apart. This causes the thermometer to rise. When the liquid in the thermometer is chilled, the molecules travel slower, leading them to get closer together.

Learn more about heat

https://brainly.com/question/1429452

#SPJ1

calculate the GPE of a 15 kg wooden block 6m above the ground​

Answers

потенциальная енергия - E=mgh, g = ускорение свободного падения, всегда равна 9.81, примерно 10: g=10. Единица измерения енергии - Джоул: [E] = Дж

от этого, E=15×10×6=900 J

ответ: 900 Дж

Based on observations (both images and spectra), which of the following statements are true about star-forming clouds?
A. Star-forming clouds are much hotter than most other interstellar material in the galaxy.
B. Star-forming clouds have the same overall chemical composition as the galaxy as a whole.
C. Most of the hydrogen in star-forming clouds is in the form of hydrogen molecules (H2).
D. The darkness of these clouds (in visible light) is due primarily to light absorption by tiny grains of interstellar dust.
E. The densest cloud regions appear dark to visible light telescopes but we can see into these regions with Infrared telescopes.
F. Young stars shine only in the infrared, which is why infrared observations are important.
G. Star-forming clouds glow with visible light in regions where the gas is heated by radiation from nearby stars.

Answers

Option B, C, D, E, and G: The chemical makeup of star-forming clouds is identical to that of the galaxy as a whole and the majority of the hydrogen in clouds that generate stars is present as hydrogen molecules (H₂).

Interstellar molecular clouds, which are opaque collections of extremely cold gas and dust, are where stars are formed. When some of those aggregates accumulate enough mass to collapse due to gravity alone, the process begins. The cause could even be as simple as random density changes within the cloud.

The correct statements are:

The chemical makeup of star-forming clouds is identical to that of the galaxy as a whole.

The majority of the hydrogen in clouds that create stars is present as hydrogen molecules (H₂).

The interstellar dust particles that make up these clouds' visual blackness absorb the majority of light.

Even though the densest cloud regions appear dark to telescopes using visible light, we can see inside them using infrared telescopes.

A region where the gas is heated by radiation from neighboring stars is where star-forming clouds are found.

To know more about the formation of stars, refer:

https://brainly.com/question/16975209

#SPJ4

A proton moves along the x-axis with v_x=1.0×10^7m/s. As it passes the origin, what are the strength and direction of the magnetic field at the (0 cm, 1 cm, 0 cm) position? Give your answer using unit vectors.

Answers

Here ya go! i think this will help!

which of the following describes the subtle gradation of light and shadow to create the effect of three dimensionality?

Answers

The subtle gradation of light and shadow to create the effect of three-dimensionality is described as shading.

In the context of art, shading refers to the use of light and shadow to render a three-dimensional object or scene realistically.

When an object is illuminated, light falls on its surface in different ways, depending on the position of the light source, the object's orientation, and the object's shape.

In this way, shadows are formed on the object's surface, and some regions receive more or less light than others.

By accurately depicting these light and shadow areas, artists can create an illusion of depth and dimensionality in their works.

for such more question on dimensiona

https://brainly.com/question/446697

#SPJ11

Can someone check my answers? If I’m incorrect can you correct me? Thank you. Image below.

Answers

Explanation:

a) looks correct  EXCEPT   KE and GPE labels are reversed ( if the one on the L is initially and the R one is at max height)

b) looks good

c)  incorrect       total energy will be KE + GPE =   57.51 J at any point

d) correct

S18-MP4 roblem 26.23 K) 8 of 10 How far does the proton travel before reaching its turning point? Express your answer with the appropriate units. View Available Hint(s) Constants | Periodic Table on an infinite charged plane is -1.60x10-6 C/m2 . A proton is shot straight away from the plane at 2.30x106 m/s Hint 1. How to approach this problem When the proton has reached its farthest point, it is standing still. This means that the work done on the proton by the electric field of the infinite sheet has exactly canceled the original kinetic energy of the proton. Hint 2. What is the work done by the sheet Recall that the electric field near an infinite sheet of charge density ? is given by E Since the electric field strength is independent of the distance from the sheet, the force is constant along the path of the proton and the work done is simply equal to the force times the distance traveled. Value Units Submit

Answers

The electric field strength near an infinite sheet of charge density σ is given by E = σ/2ε0, where ε0 is the electric constant.

The force on the proton due to the electric field of the sheet is F = qE, where q is the charge of the proton.

The work done by the sheet on the proton is W = Fd, where d is the distance traveled by the proton before reaching its turning point.

When the proton has reached its turning point, its kinetic energy is zero, so the work done by the electric field of the sheet must equal the initial kinetic energy of the proton, which is given by KE = (1/2)mv^2, where m is the mass of the proton and v is its initial velocity.

Setting these two expressions for work equal to each other, we have:

F d = (1/2)mv^2

Substituting F = qE and E = σ/2ε0, we get:

qd/2ε0 = (1/2)mv^2

Solving for d, we get:

d = mv^2/(qσε0)

Substituting the given values for m, v, q, and σ, and the value of ε0 from the constants, we get:

d = (1.67x10^-27 kg)(2.30x10^6 m/s)^2/(1.60x10^-6 C/m^2)(2ε0) ≈ 1.59x10^-5 m

Therefore, the proton travels a distance of approximately 1.59x10^-5 meters before reaching its turning point.

when a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is

Answers

When a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is perpendicular to the surface at the point where the light ray hits it.

Reflection occurs when light rays hit a surface and bounce back whereas Refraction, occurs when light travels through a medium of a different density or refractive index.

The laws of reflection and refraction states that the angle of incidence is equal to the angle of reflection, and the ratio of the sine of the angle of incidence to the sine of the angle of refraction is constant. This ratio is known as the refractive index of the material from where the light is passing through.

To know more about reflection and refraction refer to:

brainly.com/question/16957723

#SPJ4

A certain Tesla car has a 400 V battery which stores 2.9x108 J. The car can travel 402 km (250 miles) at 105 km/hr (65 mph = 29 m/s) on just the battery before it is depleted. The steps below will let you determine the current delivered by the battery.A. How long does it take to deplete the battery?B. What is the power delivered by the battery (P=E/dt)?C. Power in a circuit is related to the potential difference, current and resistance in the circuit. What is the current delivered by the battery?D. What is the resistance of the circuit?

Answers

A. Baterry takes time = 2.9x[tex]10^{8}[/tex] J / power to deplete.

What is time taken?

To determine how long it takes to deplete the battery, we can use the formula:

time = energy / power

where energy is the energy stored in the battery (2.9x[tex]10^{8}[/tex] J) and power is the power delivered by the battery (which we will determine in part B).

time = 2.9x[tex]10^{8}[/tex] J / power

B. Power delivered by the baterry is 20864.5 W

What is the power?

To determine the power delivered by the battery, we can use the formula:

power = energy / time

where energy is the energy stored in the battery (2.9x[tex]10^{8}[/tex] J) and time is the time it takes to deplete the battery (which we will determine in part A).

First, let's convert the distance traveled from kilometers to meters:

402 km = 402,000 m

Now, we can use the formula:

time = distance / speed

where distance is the distance traveled (402,000 m) and speed is the speed of the car (105 km/hr = 29 m/s).

time = 402,000 m / 29 m/s = 13896.6 s

Now we can calculate the power delivered by the battery:

power = 2.9x[tex]10^{8}[/tex] J / 13896.6 s = 20864.5 W

C.  The current delivered by the battery is 52.2 A.

What is current?

The power delivered by the battery is related to the current and potential difference in the circuit by the formula:

power = potential difference x current

The potential difference in the circuit is given as 400 V. Therefore, we can rearrange the formula to solve for the current:

current = power / potential difference

current = 20864.5 W / 400 V = 52.2 A

Therefore, the current delivered by the battery is 52.2 A.

D. We cannot directly determine the resistance of the circuit from the given information.

To know more about the power, visit:

https://brainly.com/question/28430509

#SPJ1

what is the voltage reading vr(t) given by the voltmeter across the resistor (figure 2) at time t after t

Answers

The voltage reading V,(t) across the resistor at time t after t = 0 is equal to the current I(t) multiplied by the resistance R, since V = IR. Therefore, V,(t) = RI(t).

What is resistor?

A resistor is an electrical component that reduces the flow of current in a given circuit. It is made from a conductive material, generally either carbon or metal, that has been treated to produce a specific resistance value. The resistance value of a resistor is measured in ohms, and is generally marked on the component itself. Resistors are used to limit the amount of current flowing through a circuit, which in turn can control the voltage and power levels in the circuit. They can also be used to create voltage dividers which divide the voltage of a circuit into different levels, or to provide stability to a circuit by providing a fixed current. Resistors are a fundamental component of all electronic circuits and are used in a wide range of applications.

To learn more about resistor
https://brainly.com/question/28383163
#SPJ1

Complete Question:

A large container holds 7.6 gallons of water. Use the following information to convert this amount of water to liters. Round your answer to the nearest tenth. 1 gallon = 4 quarts 1 L = 1.057 quarts​

Answers

Answer:

You can use the same conversion factor to convert liters to gallons or you can use: 1 liter = 0.264 US gallons. To find how many gallons are in 4 liters, for example: gallons = 4 liters x 0.264 gallons/liter. The liters cancel out, leaving the gallon unit: 4 liters = 1.056 gallons. Keep this in mind: there are about 4 liters per US gallon.

Explanation:

A photodetector has three polarizing films between it and a source of
unpolarized light. The first film is oriented vertically. At what angle should the
second polarizing film be oriented so that 37.5 percent of the original light
intensity reaches the detector?
Investigation 12 Electromagnetic Radiation

Answers

The angle between the polarization direction of the second film and the vertical direction should be approximately 51.4° so that 37.5% of the original light intensity reaches the detector.

Steps

Let's denote the angle between the vertical polarization direction of the first film and the polarization direction of the second film by θ. The transmitted intensity of the light after passing through the two films is given by Malus's law:

I = I₀ cos²θ

where I₀ is the initial intensity of the unpolarized light.

We want to find the angle θ that will result in 37.5% of the original light intensity reaching the detector. This means that we want to solve the equation:

I/I₀ = 0.375

Substituting the expression for I into this equation, we get:

cos²θ = 0.375 / I₀

Taking the square root of both sides and using the fact that cosθ is positive when 0 ≤ θ ≤ π/2, we get:

cosθ = √(0.375 / I₀)

θ = arccos(√(0.375 / I₀))

Now we need to substitute the values of I₀ and evaluate the expression for θ. Let's assume that the intensity of the original light is I₀ = 1 W/m². Then we get:

θ = arccos(√(0.375 / 1)) = arccos(0.6124) = 51.4°

Therefore, the angle between the polarization direction of the second film and the vertical direction should be approximately 51.4° so that 37.5% of the original light intensity reaches the detector.

learn more about photodetector here

https://brainly.com/question/16028899

#SPJ1

The magnitudes of the current density and the diameters for wires 1 and 2 are given in the table. The current directions are indicated by the arrows.
Find the current I3 in wire 3.
Express your answer in amperes to two significant figures. Call current out of the junction positive and current into the junction negative.
The magnitudes of the current density and the diam
Wire Current density
(A/mm2) Diameter
(mm)
1 2.1 1.7
2 3.9 2.4

Answers

To solve for the current I3 in wire 3, we can apply the principle of conservation of charge, which states that the total current flowing into a junction must equal the total current flowing out of the junction. This can be expressed mathematically as:

I1 + I2 = I3

where I1 and I2 are the currents in wires 1 and 2, respectively, and I3 is the current in wire 3.

To find I1 and I2, we can use the formulas for current (I = J x A), where J is the current density and A is the cross-sectional area of the wire. The cross-sectional area can be calculated from the diameter using the formula A = π/4 x d^2, where d is the diameter.

For wire 1:

I1 = J1 x A1 = 2.1 A/mm^2 x π/4 x (1.7 mm)^2 = 4.52 A

For wire 2:

I2 = J2 x A2 = 3.9 A/mm^2 x π/4 x (2.4 mm)^2 = 13.21 A

Substituting these values into the conservation of charge equation, we get:

4.52 A + 13.21 A = I3

Simplifying, we get:

I3 = 17.73 A

Therefore, the current I3 in wire 3 is approximately 17.73 amperes (or amps) to two significant figures.

What is a current ?

Current can be thought of as the rate at which electric charges flow through a circuit. It is caused by the movement of electrons, which are negatively charged particles, in response to an electric field. In a metallic conductor, such as a wire, electrons can move freely through the material, which allows current to flow easily.

Current can be either direct current (DC) or alternating current (AC). DC flows in one direction, whereas AC changes direction periodically. DC is commonly used in batteries and electronic devices, while AC is used for power transmission over long distances.

To know more about Current visit :

https://brainly.com/question/13076734

#SPJ1

A 1500-kg car is traveling at 21 m/s around a curve with a radius of 120 m. Determine the angular momentum of the car. Show your work.

Answers

Answer:

Explanation:

Angular momentum of an object is given by L = Iω, where I is the moment of inertia and ω is the angular velocity.

To find the angular momentum of the car, we need to first find its moment of inertia about the axis of rotation (which in this case is the center of the curve).

The moment of inertia of a point mass m rotating around an axis at a distance r is given by I = mr^2.

The car can be thought of as a collection of point masses, so we need to integrate the moment of inertia of each point mass over the entire car.

Assuming the car is a uniform rectangular box with dimensions 4.5 m x 1.8 m x 1.5 m, we can divide it into smaller cubes of mass dm and volume dV. The moment of inertia of each cube is given by dI = dm(r^2), where r is the distance from the cube to the axis of rotation.

Integrating over the entire car, we get:

I = ∫(dm)(r^2) = ∫(ρdV)(r^2)

where ρ is the density of the car.

The volume of the car is V = (4.5 m)(1.8 m)(1.5 m) = 12.15 m^3, and assuming a density of 1000 kg/m^3 (typical for cars), the mass of the car is m = (1000 kg/m^3)(12.15 m^3) = 12150 kg.

We can express the distance r as the sum of the radius of the curve (120 m) and the distance between the center of mass of the car and the pivot point (which we can approximate as half the length of the car, or 0.75 m).

So, r = 120 m + 0.75 m = 120.75 m.

Substituting these values into the equation for I, we get:

I = ∫(ρdV)(r^2) = ρ∫dV(r^2) = ρV(r^2) = (1000 kg/m^3)(12.15 m^3)(120.75 m)^2 = 1.796 x 10^7 kg·m^2

To find the angular velocity of the car, we can use the formula v = ωr, where v is the linear velocity of the car and ω is the angular velocity.

The linear velocity of the car is given by v = 21 m/s, and the radius of the curve is 120 m. So,

ω = v/r = (21 m/s)/(120 m) = 0.175 rad/s

Finally, we can find the angular momentum of the car by multiplying the moment of inertia by the angular velocity:

L = Iω = (1.796 x 10^7 kg·m^2)(0.175 rad/s) = 3.145 x 10^6 kg·m^2/s

Therefore, the angular momentum of the car is 3.145 x 10^6 kg·m^2/s.

The angular momentum of the car in the given example is [tex]3,780,000 kg m^2/s.[/tex]

What is an Angular momentum?

The amount of rotational motion an object has around a certain axis is measured by its angular momentum. It is the result of an object's angular velocity and moment of inertia. It is a vector quantity with a direction and magnitude.

We need to apply the following calculation to determine the car's angular momentum:

L = I * ω

where L is angular momentum, I is the moment of inertia, and ω is the angular velocity.

We must apply the following formula to determine the moment of inertia:

[tex]I = m * r^2[/tex]

where r is the curve's radius and m is the car's mass.

m = 1500 kg r = 120 m

[tex]I = m * r^2[/tex]

[tex]I = 1500 kg * (120 m)^2\\I = 21,600,000 kg m^2[/tex]

The following formula must be used to determine the angular velocity:

v = ω * r

where v denotes the car's speed.

v = 21 m/s r = 120 m

where,

v/r = 21 m/s/120 m = 0.175 rad/s

We can now determine the angular momentum:

L = I * ω

[tex]L = 21,600,000 kg m^2 * 0.175 rad/s\\L = 3,780,000 kg m^2/s[/tex]

Therefore, the angular momentum of the car is [tex]3,780,000 kg m^2/s.[/tex]

Learn more about angular momentum, here:

https://brainly.com/question/29563080

#SPJ2

An automobile engine slows down from 4500 rpm to 1200 rpm in 2.5 s. Calculate:
a) Its angular acceleration, assumed constant.
b) the total number of revolutions the engine makes in this time

Answers

a. The angular acceleration of the engine is -1320 rad/s².

b. The engine makes approximately 118.7 revolutions during the deceleration.

Given:

Initial angular velocity (ω1) = 4500 rpm

Final angular velocity (ω2) = 1200 rpm

Time is taken (t) = 2.5 s

a) The formula for angular acceleration is:

α = (ω2 - ω1) / t

Substituting the given values, we get:

α = (1200 rpm - 4500 rpm) / 2.5 s = -1320 rad/s² (negative sign indicates a deceleration)

Therefore, the angular acceleration of the engine is -1320 rad/s².

b) To find the total number of revolutions, we need to convert the initial and final angular velocities from rpm to rad/s:

ω1 = 4500 rpm × 2π/60 = 471 rad/s

ω2 = 1200 rpm × 2π/60 = 126 rad/s

The average angular velocity (ω_avg) during the deceleration is given by:

ω_avg = (ω1 + ω2) / 2 = (471 rad/s + 126 rad/s) / 2 = 298.5 rad/s

The total angular displacement (θ) of the engine during the deceleration is given by:

θ = ω_avg × t = 298.5 rad/s × 2.5 s = 746.25 rad

Finally, the total number of revolutions (N) made by the engine is:

N = θ / 2π = 746.25 rad / 2π rad/rev = 118.7 rev (approximately)

Therefore, the engine makes approximately 118.7 revolutions during the deceleration.

learn more about angular acceleration here

https://brainly.com/question/21278452

#SPJ1

Estimat the number and wattage of lamps. which would be required to illuminate a workshop space 60x1.5 meteres by means of lamps mounted 5 metres above the working Plane The average illumination required is about 100 wt. coefficient of utilisation = 0.4 luminous efficiency 16 lumens per watt. Assume a space-height ratio of unity and a cundle Power depreciation of 20%​

Answers

The number and wattage of lamps required to illuminate the workshop would be approximately 8 lamps and 70 watts respectively.

Wattage calculation

To estimate the number and wattage of lamps required to illuminate a workshop space of 60x1.5 meters, we can follow these steps:

Calculate the area of the workshop:

Area = length x widthArea = 60m x 1.5mArea = 90 square meters

Determine the total lumens required:

Lumens = area x average illuminationLumens = 90 sq m x 100 luxLumens = 9000 lumens

Adjust for the coefficient of utilization and luminous efficiency:

Effective lumens = lumens / (coefficient of utilization x luminous efficiency)Effective lumens = 9000 / (0.4 x 16)Effective lumens = 1406.25 lumens

Adjust for space-height ratio and candle power depreciation:

Effective lumens per lamp = effective lumens x space-height ratio x (1 - depreciation)Effective lumens per lamp = 1406.25 x 1 x (1 - 0.2)Effective lumens per lamp = 1125 lumens

Determine the number of lamps required:

Number of lamps = total lumens required / effective lumens per lampNumber of lamps = 9000 / 1125Number of lamps = 8 lamps (rounded up)

Determine the wattage of each lamp:

Wattage per lamp = effective lumens per lamp / luminous efficiencyWattage per lamp = 1125 / 16Wattage per lamp = 70.3 watts (rounded up)

Therefore, approximately 8 lamps with a wattage of 70 watts each would be required to illuminate the workshop space.

More on wattage can be found here: https://brainly.com/question/14667843

#SPJ1

sort each of the astronomical questions below into the appropriate bin based on the type of observation you would need to perform to answer it.

Answers

Imaging: How big is the Andromeda Galaxy? What are the prime surface features of Mars? Are the stars in the Orion Nebula surrounded by gas?

Spectroscopy: What is the chemical composition of Crab Nebula? Determine the temperature of Jupiter's atmosphere?

Timing: Does the star Mira vary in it's brightness?

Give a brief account on Spectroscopy.

Spectroscopy is known to be the study of the absorption and emission of light and other radiation by matter. It is related that these processes depend on the wavelength of the radiation. Recently, the definition has been extended to include the study of interactions between particles like electrons, protons and ions, and interactions with other particles as a function of collision energy.

Spectroscopy has been essential to the development of some of the most fundamental theories of physics, including quantum mechanics, special and general relativity, and quantum electrodynamics. Spectroscopy applied to high-energy collisions has become an important tool in advancing the scientific understanding not only of electromagnetic forces, but also of strong and weak nuclear forces.

To know more about  Spectroscopy, visit:

https://brainly.com/question/5402430

#SPJ1

You have been called to testify as an expert witness in a trial involving a head-on collision. Car A weighs 1515
lb and was traveling eastward. Car B weighs 1125
lb and was traveling westward at 41.0
mph. The cars locked bumpers and slid eastward with their wheels locked for 18.5
ft before stopping. You have measured the coefficient of kinetic friction between the tires and the pavement to be 0.750
.

What speed
(in miles per hour) was car A traveling just before the collision? (This problem uses English units because they would be used in a U.S. legal proceeding.)

Answers

Answer:

Solve for force:

Ff = UFn

Ff = 0.75(Fn)

Ff = 0.75(1515 + 1225 * g)

Ff = 20550N

Solve for acceleration:

F= ma

20550N = (1515 + 1225) a

a = 7.5m/s^2

solve for time:

a = d / t^2  --->  7.5m/s^2 = 18.5/ t^2  ----> t = 0.85s

solve for velocity final

Impulse = F * t = 20550N * 0.85s

mv^2 = Impulse = 17467.5

(1515 + 1125)v^2 = 17467.5

vf = 2.5m/s

Plug in stuff:

1515 * v1 + 1125 * (-18.3m/s) = (1515 + 1125) * 2.5m/s

v1 = 9.23

Note: I converted 41mph(v2) to 18.3m/s, which is negative because "westward" is in the negative direction.

Explanation: Inelastic collision

I'm not sure but my guess is we can solve for the force of friction using the coefficient of friction. With that, we can solve for the acceleration in F = ma, and use that to solve for the time the two cars slide. And using that we can solve for the impulse, which is just the Force of friction times that time, which is also our momentum. Since we know the momentum, we can solve for the velocity of the two objects after the collision. Using that velocity, we can use the equation( m1v1 + m2v2 = (m1+m2)vf ), plug in the known quantities and solve for v1.(Note: don't forget to convert mph to mps and 18.5ft to meters)

Extra: I'm guessing because the two cars slide, the only force acting on them is the force of friction(so it's our net force), hence the Fnet = ma.

there is very little hydrogen or helium in the inner part of the solar system today. astronomers believe the reason for this is that

Answers

Astronomers believe that the reason for the low levels of hydrogen and helium in the inner part of the Solar System is that these elements were lost due to the Sun's strong solar wind

. Most of the gas in the solar nebula was hydrogen and helium. However, there is very little hydrogen or helium in the inner part of the solar system today. Astronomers believe this is because the intense solar winds from the young Sun blew the lighter gases out into space.

The solar winds also blew away any smaller particles that had not yet stuck together to form larger objects, which is why there are very few small objects close to the Sun. This is why there is more hydrogen and helium in the outer part of the solar system.

Know more about  Astronomers here:

https://brainly.com/question/2141924

#SPJ11

lonie is being pulled from a snake pit with a rope that breaks if tension in it exceeds 755N. If one has a mass of 70kg and the snake pit is 3 Am deep, what is the minimum time necessary to pull out lonie?

Answers

The minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

Given: Mass, m = 70 kg Distance, d = 3 m Limiting tension, T = 755N

The minimum time required to pull out lonie from a snake pit, t

Given, mass, m = 70 kg Acceleration due to gravity, g = 9.8 m/s²Distance, d = 3 m

Let's assume the minimum time required to pull out lonie from a snake pit is t.

So, using the equation of motion,S = ut + 1/2 at²

Here, S = d = 3m (Distance),u = 0 m/s (Initial velocity),a = g = 9.8 m/s² (Acceleration) and t = time

Substituting the above values in the equation, we get3 = 0 + 1/2 × 9.8 × t² => t² = 3/4 => t = √(3/4) sec

Also, we know that the tension in the rope is given byT = mg + ma

Now, the rope will break when T exceeds 755 N.

So, substituting the values of m, g, and a in the above equation, we getT = mg + ma = 70 × 9.8 + 70 × a

Since the tension in the rope should be less than or equal to 755 N, we have70 × 9.8 + 70 × a ≤ 755 => a ≤ (755 - 70 × 9.8)/70=> a ≤ 3.29 m/s²

Therefore, the minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

for such more question on minimum time

https://brainly.com/question/14517981

#SPJ11

jason weighs 150 n and sits on his big brother's shoulders. his big brother weighs 400 n. the support force supplied by the floor must be

Answers

Jason weighs 150 N and sits on his big brother's shoulders. Big brother weighs 400 N. the support force supplied by the floor must be 500N.

Force can be defined as any influence that causes an object to undergo a change in motion, direction, or shape. In physics, force is represented as a vector quantity, which means it has both magnitude and direction. The standard unit of force is the newton, which is defined as the force required to accelerate a mass of one kilogram at a rate of one meter per second squared.

Force can be categorized into two types: contact force and non-contact force. Contact force is a force that is exerted through direct contact between two objects, while non-contact force is a force that is exerted without any physical contact between two objects, such as gravity or electromagnetic force. Force plays a crucial role in the study of physics, as it governs the behavior of all objects in the universe.

To learn more about Force visit here:

brainly.com/question/31046192

#SPJ4

Complete Question:-

Jason weighs 150 N and sits on his big brother's shoulders. Big brother weighs 400 N. the support force supplied by the floor must be

P2. Charges q and Q are placed on the x-y plane at (0,0) and at (0, 3) m, respectively.
Where q = 50 pC and Q = -40 pC.
a. Draw the situation to solve the next step.
b. Determine the net electric flux through a closed cylindrical surface that has a diameter of 5 ma
a height of 4 m, where the axis of the cylinder is the z axis and its mid-point is at the origin.

Answers

a. Here is a diagram of the situation:

                Q (-40 pC)

       |

       |

       |    (0,3)

       |

------ o-------- x-axis

       |

       |

       |    (0,0)

       |

     q (50 pC)

(b) The net electric flux through the closed cylindrical surface is -5.69×10⁵ Nm²/C.

To calculate this, we use Gauss's Law, which states that the net electric flux through any closed surface is proportional to the net charge enclosed by the surface. Mathematically, this is expressed as:

flux = E * A = (q_enclosed / ε0) * A

where E is the electric field, A is the area of the closed surface, q_enclosed is the net charge enclosed by the surface, and ε0 is the permittivity of free space.

In this case, we have a cylindrical surface with a height of 4 m and a diameter of 5 mA (which means a radius of 2.5 mA). The cylinder is centered at the origin and has the z-axis as its axis of symmetry. To apply Gauss's Law, we need to find the net charge enclosed by the cylinder.

Both charges q and Q are on the x-y plane, so they do not contribute to the net charge enclosed by the cylindrical surface. Therefore, the net charge enclosed by the surface is simply the sum of q and Q:

q_enclosed = q + Q = (50 pC) + (-40 pC) = 10 pC

Substituting this into Gauss's Law, we get:

flux = (q_enclosed / ε0) * A = (10 pC / 8.85×10⁻¹² F/m) * π (2.5×10⁻³ m)² (4 m) = -5.69×10⁵ Nm²/C

Therefore, the net electric flux through the closed cylindrical surface is -5.69×10⁵ Nm²/C.

What is an electric flux?

Electric flux is the measure of the number of electric field lines passing through a given surface. It is a scalar quantity and represents the amount of electric field passing through a surface per unit area. The SI unit of electric flux is volt-meter (V m) or newton-meter squared per coulomb (N m2/C).

To know more about electrical flux, visit:

https://brainly.com/question/14544020

#SPJ1

2020 State of the Bay Summary PLS HELP PLS ILYSM IF U DO!!!!

What are your first feelings or impressions when looking at the tables above?

Which indicators do you believe are most important for the health of the Bay? Explain.

Chesapeake Bay Report Grade vs. Year Graph

From your viewpoint, 1) what does the graph reveal about the current state of the Chesapeake Bay? 2) Do you believe your community contributes to the Chesapeake Bay’s condition? Explain your answer.

Answers

There is likely to be eutrophication in the water

There are less turbid substances deposited in the water within the time.

The decrease of water grasses means the primary productivity reduced.

What does increase in nitrogen and phosphorus content mean for Chesapeake Bay ?

An increase in nitrogen and phosphorus content in Chesapeake Bay can have significant environmental impacts. Chesapeake Bay is an estuary that is highly sensitive to nutrient pollution, which can cause the growth of harmful algal blooms and oxygen depletion in the water.

When excess nitrogen and phosphorus from fertilizers, animal waste, and sewage enter the Bay, they can cause an overgrowth of algae. As these algae die and decompose, they consume oxygen in the water, leading to low oxygen conditions known as "hypoxia" or "dead zones". This can harm fish, shellfish, and other aquatic life, and can also have economic impacts on the fishing and tourism industries.

Learn more about Chesapeake Bay:https://brainly.com/question/14295402

#SPJ1

Check the correctness of the following equation , a=v^2/r, where a=acceleration, v=velocity, r= radius

Answers

Answer:

check

Explanation:

resistance of wire does not depend on ____current supplied area of cross-section of the wire length of the wire material of the wire

Answers

Resistance of wire does not depend on current supplied, area of cross-section of the wire, length of the wire, or material of the wire.


The resistance of a wire does not depend on the current supplied. The resistance of a wire is determined by the following factors:

Length of the wire: The longer the wire, the more resistance it will have. This is due to the fact that a longer wire has more atoms that obstruct the flow of electrons. The more time the electrons take to traverse the wire, the more collisions they will have, resulting in more resistance.

Area of cross-section of the wire: The cross-sectional area of a wire is inversely related to its resistance. This implies that if the cross-sectional area is reduced, the resistance will rise. This is due to the fact that a smaller cross-sectional area leads to more electron collisions with atoms.

Material of the wire: The resistivity of the wire's material determines its resistance. A material with a higher resistivity would have more resistance than one with a lower resistivity. It's important to note that the resistivity of a material varies with temperature. As the temperature rises, so does the resistivity of the substance.

For more such questions on Resistance , Visit:

https://brainly.com/question/30901006

#SPJ11

Two balls collide and bounce off of each other. Ball A has a mass of 4.00kg and an initial velocity of 10.0m/s. Ball B has a mass of 6.00kg and an initial velocity of
-5.00m/s.
A. What is the initial momentum of the system?
B. Ball B bounces off with a velocity of 7.00m/s. What is the velocity of Ball A?
C. Prove if this is a perfectly elastic collision or not.

Answers

For Answer refer to the attached image
Other Questions
The hanger image below represents a balanced equation. Write an equation to represent the imageHELP THIS IS DUE TODAY Some protists, such as amoebas, are surrounded only by their plasma membrane whereas others such as diatoms and foraminifera are surrounded by? student a sprayed perfume in a cold room and it took 30 seconds for it to disperse throughout the room. student b sprayed perfume in a heated room and it took 10 seconds for it to disperse throughout the room. based on the kmt, compare these two rooms with respect to temperature, kinetic energy, particle motion and velocity. what three elements are considered part of the promotional mix? What types of weathering contribute to the lead problem in Picher, Oklahoma? a. Frost wedging b. Biological c. Dissolution d. All of the above. Calculate the pH at 25C of a 0.73M solution of potassium acetate KCH3CO2. Note that acetic acid HCH3CO2 is a weak acid with a pKa of 4.76 . Round your answer to 1 decimal place. what are some of the potential drawbacks to switching from incandescent to compact fluorescent light bulbs? which of the following was not a key characteristic of a dss? a. easy-to-use interactive interface b. designed or customized by it professionals c. models or formulas for sensitivity analysis, what if analysis, goal seeking, and risk analysis In the brown alga Laminaria, the large, leafy-looking thallusA) grows from a zygote.B) is a sporophyte.C) has sporangia.D) is diploid.E) ALL OF THE ABOVE When reporting on a nonissuer's internal control over financial reporting in a separate report, a practitioner should include a paragraph that describes theA.Documentary evidence regarding the control environment factors.B.Changes in the internal control structure since the prior report.C.The practitioner's responsibility to detect material misstatements in account balances.D.The criteria against which the internal control was measured.SHOW CORRECT ANSWER What type of government was in place in China from 1949 forward? The GSSP concept was introduced in the ______, to provide accepted definitions for ______ units. There is some evidence that pharyngeal gill slits occur in certain species of echinoderms that appear early in the fossil record. If confirmed, what do these data suggest? In the context of entrepreneurial orientation, an organization with a tendency of _____ grants individuals and teams the freedom to exercise their creativity, champion promising ideas, and carry them through to completion.Multiple Choiceinnovativenesscompetitive aggressivenessproactivenessindependent actionrisk taking write the relationship between cells tissue and organs in human body Perez Company is a retail company that specializes in selling outdoor camping equipment. The company is considering opening a new store on October 1, year 1. The company president formed a planning committee to prepare a master budget for the first three months of operation. As budget coordinator, you have been assigned the following tasks.RequiredOctober sales are estimated to be $220,000, of which 45 percent will be cash and 55 percent will be credit. The company expects sales to increase at the rate of 20 percent per month. Prepare a sales budget.The company expects to collect 100 percent of the accounts receivable generated by credit sales in the month following the sale. Prepare a schedule of cash receipts.The cost of goods sold is 60 percent of sales. The company desires to maintain a minimum ending inventory equal to 10 percent of the next months cost of goods sold. However, ending inventory of December is expected to be $13,000. Assume that all purchases are made on account. Prepare an inventory purchases budget.The company pays 80 percent of accounts payable in the month of purchase and the remaining 20 percent in the following month. Prepare a cash payments budget for inventory purchases.Budgeted selling and administrative expenses per month follow:Salary expense (fixed) $ 19,000 Sales commissions 5 % of SalesSupplies expense 2 % of SalesUtilities (fixed) $ 2,400 Depreciation on store fixtures (fixed)* $ 5,000 Rent (fixed) $ 5,800 Miscellaneous (fixed) $ 2,200 *The capital expenditures budget indicates that Perez will spend $210,000 on October 1 for store fixtures, which are expected to have a $30,000 salvage value and a three-year (36-month) useful life.Use this information to prepare a selling and administrative expenses budget.Utilities and sales commissions are paid the month after they are incurred; all other expenses are paid in the month in which they are incurred. Prepare a cash payments budget for selling and administrative expenses.Perez borrows funds, in increments of $1,000, and repays them on the last day of the month. Repayments may be made in any amount available. The company also pays its vendors on the last day of the month. It pays interest of 1 percent per month in cash on the last day of the month. To be prudent, the company desires to maintain a $22,000 cash balance. Prepare a cash budget. A portable hair dryer on the conducts 15-5/8 amperes (1875 watts). What is the effective resistance of the heating element and motor? Assume the 12.5 amperes flows through the heating element, what is the effective resistance of the heating element? How much is the effective resistance of the motor. Note the motor can operate independently of the heating element as a cool down setting. Victor spent $61 on some sandpaper for his modelcars. He bought 2 packages of the smallest-grainsandpaper and spent the rest on the largest-grainsandpaper. How many packages of the largest-grain sandpaper did he buy? What is 15426.82 rounded to the nearest hundredth True/False? One of the ways to represent superclass and subclass relationships when mapping EER Model Diagrams into Relational Schema is by creating a single relation for the superclass that also includes all of the subclass attributes, along with a single discriminating attribute that indicates which subclass each tuple is contained. This method works whether the superclass whether the relationship is disjoint or overlapping