The wavelength of the light produced in the transition from a spin-up to spin-down state is 5.37 × 10^-7 m or 537 nm.
The energy difference between the spin-up and spin-down states of a hydrogen atom in a magnetic field is given by:
ΔE = gμB * B
where g is the Landé g-factor, μB is the Bohr magneton, and B is the magnetic field strength.
For a hydrogen atom, g = 2.0023 and μB = 9.274 × 10^-24 J/T.
So, ΔE = (2.0023)(9.274 × 10^-24 J/T)(200 T) = 3.71 × 10^-20 J.
The energy of a photon is given by:
E = hν
where h is Planck's constant and ν is the frequency of the photon.
The wavelength λ of the photon is given by:
λ = c/ν
where c is the speed of light.
Combining these equations, we get:
λ = hc/ΔE
Plugging in the values, we get:
λ = (6.626 × 10^-34 J s)(3.00 × 10^8 m/s)/(3.71 × 10^-20 J) = 5.37 × 10^-7 m
learn more about wavelengths here :
brainly.com/question/31866915
#SPJ4
f) If the resistance of a circuit is quadrupled, by what factor does the current change?
When the resistance of a circuit is quadrupled, the current changes by a factor of one-fourth.
When the resistance of a circuit is quadrupled, the current through the circuit changes by a factor of one-fourth. This relationship is governed by Ohm's law, which states that the current flowing through a circuit is directly proportional to the voltage and inversely proportional to the resistance.
Mathematically, Ohm's law can be expressed as I = V/R, where I represents the current, V represents the voltage, and R represents the resistance.
When the resistance is quadrupled, it means the new resistance (R') is four times the original resistance (R). Therefore, R' = 4R. By substituting this value into Ohm's law, we get I' = V/(4R). Simplifying further, we find that I' = (1/4) * (V/R) = (1/4) * I.
This implies that the new current (I') is one-fourth of the original current (I). Hence, when the resistance of a circuit is quadrupled, the current changes by a factor of one-fourth.
For more such questions on resistance
https://brainly.com/question/28135236
#SPJ11
true/false. let f be a composition of two reflections in two hyperbolic lines prove that if the two lines are parallel, then f is parabolic.
Let f be a composition of two reflections in two hyperbolic lines. If the two lines are parallel, then f is parabolic. The given statement is true because the composition of two reflections in these lines results in a parabolic transformation
To prove this, we need to consider the composition of two reflections in hyperbolic geometry. A reflection in a hyperbolic line is an isometry that maps a point to its mirror image with respect to that line. When we compose two reflections in two distinct hyperbolic lines, the resulting transformation is either a translation, a rotation, or a parabolic transformation.
In our case, we are given that the two hyperbolic lines are parallel. In hyperbolic geometry, this means that they do not intersect and they share a common perpendicular line. When we compose two reflections in parallel lines, we can observe that the transformation preserves orientation and has a unique fixed point on the common perpendicular line. This unique fixed point is called the "parabolic fixed point," and the transformation that possesses such a point is called a parabolic transformation. Therefore, if the two lines are parallel, the composition of two reflections in these lines results in a parabolic transformation, and our statement is true.
Learn more about hyperbolic geometry here:
https://brainly.com/question/8531346
#SPJ11
The cart and its load have a total mass of 100 kg and center of mass at G. Determine the acceleration of the cart and the normal reactions on the pair of wheels at A and B. Neglect the mass of the wheels 100 N 1.2 m 0.5 m 0.3 m 0.4m 0.6 m The 100 kg wheel has a radius of gyration about its center O of ko-500 mm. If the wheel starts from rest, determine its angular velocity in t-3s.
The acceleration of the cart is 1.962 m/s^2, and the angular velocity of the wheel after 3 seconds is 11.772 rad/s.
To solve this problem, we need to find the net force acting on the cart and its acceleration using the principle of linear momentum. Then, we can use the principle of angular momentum to find the angular velocity of the wheel.
First, we find the center of mass of the cart and its load. Using the formula for the center of mass,
xG = (m1*x1 + m2*x2 + m3*x3 + m4*x4 + m5*x5) / (m1 + m2 + m3 + m4 + m5)
= (100*0 + 100*1.2 + 100*0.5 + 50*0.3 + 50*0.4) / 300
= 0.7 m
Next, we can find the net force acting on the cart by analyzing the forces acting on it. We have the weight of the system acting downwards, and the normal forces at A and B acting upwards. Since the cart is not accelerating vertically, the net force in the y-direction must be zero. Therefore, the normal forces at A and B are equal to the weight of the system, which is:
N = 1000 N
To find the net force in the x-direction, we use the principle of linear momentum:
F_net = m*a_G
= 100*a_G
where a_G is the acceleration of the center of mass. Since the forces acting in the x-direction are the force of friction acting backwards, and the force of tension in the rope acting forwards, we have:
F_net = T - f
where T is the tension in the rope, and f is the force of friction. Since the wheel is rolling without slipping, we have:
f = (1/2)*m*g
where g is the acceleration due to gravity. Also, the tension T is equal to:
T = m*a
where a is the linear acceleration of the wheel.
Using the principle of rotation, we have:
I*alpha = T*r
where I is the moment of inertia of the wheel about its center of mass, alpha is the angular acceleration, and r is the radius of the wheel. Since the wheel starts from rest, its initial angular velocity is zero, and we can use the equation:
omega = alpha*t
to find the angular velocity after time t.
Substituting the given values, we have:
I = m*k^2
= 100*(0.5)^2
= 25 kg*m^2
r = 0.5 m
f = (1/2)*m*g
= (1/2)*100*9.81
= 490.5 N
T = m*a
F_net = T - f
= m*a - (1/2)*m*g
F_net = m*a_G
= 100*a_G
I*alpha = T*r
omega = alpha*t
Substituting T and alpha from the above equations, we get:
m*a*r = m*a - (1/2)*m*g
I*alpha = m*a*r
omega = alpha*t
Solving these equations, we get:
a = 1.962 m/s^2
alpha = a/r = 3.924 rad/s^2
omega = alpha*t = 11.772 rad/s
For more such questions on acceleration:
https://brainly.com/question/30499732
#SPJ11
The cart and its load have a total mass of 100 kg with the center of mass at G. To determine the acceleration of the cart and the normal reactions on the pair of wheels at points A and B, we need to consider the forces acting on the system.
Since the cart's total weight is 100 kg and the gravitational force acting on it is 9.81 m/s², the weight W can be calculated as W = mass × gravity, which is W = 100 kg × 9.81 m/s² = 981 N. This force is acting vertically downwards at the center of mass G. Next, we need to consider the normal reactions on the pair of wheels at A and B. Let NA and NB represent the normal reactions at points A and B, respectively. These forces act vertically upwards, and for the cart to be in equilibrium, the sum of the forces in the vertical direction should be zero. Thus, NA + NB = W = 981 N. To determine the acceleration of the cart, we would need additional information about the forces acting in the horizontal direction, such as friction or an applied force. Without this information, it's not possible to calculate the acceleration of the cart. Regarding the 100 kg wheel with a radius of gyration (kO) of 500 mm, if it starts from rest, we need to determine its angular velocity after 3 seconds (t = 3s). However, we cannot calculate the angular velocity without knowing the torque or angular acceleration acting on the wheel. Additional information is needed to solve this part of the problem.
Learn more about torque here :
https://brainly.com/question/31248352
#SPJ11
A series RLC circuit consists of a 96.0 Ω resistor, a 0.150 H inductor, and a 44.0 μF capacitor. It is attached to a 120 V/60 Hz power line.
What is the peak current I at this frequency?
What is the phase angle ϕ?
What is the average power loss?
The peak current I is approximately 0.848 A, the phase angle ϕ is approximately -0.360 radians, and the average power loss in the circuit is approximately 69.6 W.
To solve for the peak current I at 60 Hz frequency, we need to first calculate the impedance Z of the circuit using the formula:
Z = sqrt(R²+ (ωL - 1/(ωC))²)
where R is the resistance, L is the inductance, C is the capacitance, and ω is the angular frequency (2πf).
Plugging in the given values, we get:
Z = sqrt((96.0 Ω)² + (2π(60 Hz)(0.150 H) - 1/(2π(60 Hz)(44.0 μF)))²) ≈ 200.1 Ω
The peak current I can then be calculated using Ohm's law:
I = Vpeak / Z
where Vpeak is the peak voltage of the power line, which is 120√2 ≈ 169.7 V. Plugging in the values, we get:
I = 169.7 V / 200.1 Ω ≈ 0.848 A
To find the phase angle ϕ, we can use the formula:
ϕ = arctan((ωL - 1/(ωC)) / R)
Plugging in the values, we get:
ϕ = arctan((2π(60 Hz)(0.150 H) - 1/(2π(60 Hz)(44.0 μF))) / 96.0 Ω) ≈ -0.360 radians
The average power loss in the circuit can be calculated using the formula:
Pavg = I² R
Plugging in the values, we get:
Pavg = (0.848 A)² (96.0 Ω) ≈ 69.6 W
Therefore, the peak current I is approximately 0.848 A, the phase angle ϕ is approximately -0.360 radians, and the average power loss in the circuit is approximately 69.6 W.
To learn more about angular frequency here
https://brainly.com/question/3654452
#SPJ4
Consider a sparingly soluble salt, A3B2, with a solubility product equilibrium constant of 4.6 x 10-11 Determine the molar solubility of the compound in water. O. 6.8 x 106M O. 8.6 x 10-3M O. 6.0 x 10-3M O. 3.4 x 10 PM O. 2.8 x 100M
The molar solubility of the sparingly soluble salt, A3B2, in water can be determined using the solubility product equilibrium constant. The correct answer is 6.0 x 10-3M.
To calculate the molar solubility, we use the equation for the solubility product equilibrium constant: Ksp = [A3+][B2-]2. Since the salt dissociates into one A3+ ion and two B2- ions, we can write the equation as Ksp = [A3+][B2-]2 = x(2x)2 = 4x3. Plugging in the given value of Ksp = 4.6 x 10-11, we can solve for x, which gives us x = 6.0 x 10-3M. Therefore, the molar solubility of A3B2 in water is 6.0 x 10-3M.
Learn more about Molar solubility:
https://brainly.com/question/16243859
#SPJ11
Light with an intensity of 62000 w/m2 falls normally on a surface with area 0.900 m2 and is completely reflected. the force of the radiation on the surface is:________
The force of radiation on the surface can be calculated using the formula F = IA, where F is the force, I is the intensity of radiation, and A is the area of the surface. In this case, we have an intensity of 62000 w/m2 and an area of 0.900 m2. So, plugging these values into the formula we get:
F = (62000 w/m2) x (0.900 m2)
F = 55800 N
Therefore, the force of radiation on the surface is 55800 N. This is because when light is reflected, it exerts a pressure on the surface that is equivalent to the force of the photons hitting it. This force can be significant, especially in situations where high-intensity light is being reflected, such as in laser applications or in solar energy collection. It is important to consider this force when designing systems that involve the reflection of light, in order to ensure that the materials used can withstand the pressure.
The intensity of a light beam with a wavelength of 400 nm is 2500 W/m2.The photon flux is about A. 5 x 10^25 photons/m^2.s B. 5 x 10^17 photons/m^2.s
C. 5 x 10^23 photons/m^2.s D. 5 x 10^21 photons/m^2.s E. 5 x 10^19 photons/m^2.s
The closest answer choice is E. 5 x 10¹⁹ photons/m².s.
We can use the formula relating intensity and photon energy to calculate the photon flux:
Intensity = Photon Energy x Photon Flux
The energy of a photon with a wavelength of 400 nm can be calculated using the formula:
Photon Energy = hc/λ
where h is Planck's constant (6.626 x 10⁻³⁴ J.s), c is the speed of light (3.00 x 10⁸m/s), and λ is the wavelength in meters. Thus, we have:
Photon Energy = hc/λ = (6.626 x 10⁻³⁴ J.s)(3.00 x 10⁸ m/s)/(400 x 10⁻⁹m) = 4.97 x 10⁻¹⁹ J
Substituting the given values into the first equation and solving for photon flux, we get:
Photon Flux = Intensity / Photon Energy = 2500 W/m² / 4.97 x 10⁻¹⁹ J = 5.02 x 10¹⁸ photons/m².s
Therefore, the closest answer choice is E. 5 x 10¹⁹ photons/m².s.
Learn more about photon flux at: https://brainly.com/question/15589622
#SPJ11
A 4.1-cm-long slide wire moves outward with a speed of 130 m/s in a 1.6 T magnetic field. At the instant the circuit forms a 4.1cm×4.1cm square, with R = 1.6×10−2 Ω on each side. A)What is the induced emf? B)What is the induced current? C)What is the potential difference between the two ends of the moving wire?
The induced emf is -0.353 V, the induced current is -22.1 A, and the potential difference between the two ends of the moving wire is -0.354 V.
A) The induced emf can be found using Faraday's law of electromagnetic induction, which states that the induced emf (ε) is equal to the rate of change of magnetic flux (Φ) through the circuit. The magnetic flux can be calculated as the product of the magnetic field (B), the area (A), and the cosine of the angle between them. In this case, the area of the circuit is A = (4.1 cm) x (4.1 cm) = 1.68 x 10⁻³ m², and the angle between the magnetic field and the normal to the circuit is 0 degrees since they are parallel.
Thus, Φ = B x A x cos(0) = 1.6 T x 1.68 x 10⁻³ m² x 1 = 2.688 x 10⁻³ Wb. Since the slide wire is moving outward with a speed of v = 130 m/s, the rate of change of magnetic flux is given by dΦ/dt = B x A x dv/dt x cos(0) = 1.6 T x 1.68 x 10⁻³ m² x (130 m/s) x cos(0) = 0.353 Wb/s. Therefore, the induced emf is ε = -dΦ/dt = -0.353 V.
B) The induced current can be found using Ohm's law, which states that the current (I) is equal to the voltage (V) divided by the resistance (R). In this case, the resistance of each side of the square circuit is R = 1.6 x 10⁻² Ω, and the induced emf is ε = -0.353 V. Thus, the induced current is I = ε/R = -0.353 V / (1.6 x 10⁻² Ω) = -22.1 A. The negative sign indicates that the current flows in the opposite direction of the movement of the wire.
C) The potential difference between the two ends of the moving wire can be found using the formula for electric potential difference, which states that the potential difference (ΔV) is equal to the product of the current (I) and the resistance (R). In this case, the current is I = -22.1 A, and the resistance is R = 1.6 x 10⁻² Ω. Thus, the potential difference is ΔV = I x R = (-22.1 A) x (1.6 x 10⁻² Ω) = -0.354 V. The negative sign indicates that the potential difference is in the opposite direction of the movement of the wire.
To know more about the moving wire refer here :
https://brainly.com/question/29105136#
#SPJ11
which term best describes the quantity of water moving through a stream?
Explanation:
Generally, stream flows are measured in CFS = Cubic Feet per Second
A student holds a spinning bicycle wheel while sitting motionless on a stool that is free to rotate about a vertical axis through its center (see the figure below). The wheel spins with an angular speed of 16.1 rad/s and its initial angular momentum is directed up. The wheel's moment of inertia is 0.130 kg · m2 and the moment of inertia for the student plus stool is 3.30 kg · m2.
The final angular velocity of the system is 0.612 rad/s.
We can substitute the given values (I_wheel = 0.130 kg · m^2, ω_wheel = 16.1 rad/s, I_student+stool = 3.30 kg · m^2) into the equation to find the final angular velocity (ω_final) of the system.
To analyze the situation, we need to consider the conservation of angular momentum. Initially, the student, stool, and wheel are at rest, so the total angular momentum is zero. As the student holds the spinning bicycle wheel, they exert a torque on the system, causing it to rotate.
The total initial angular momentum of the system is given by the sum of the angular momentum of the wheel (L_wheel) and the angular momentum of the student plus stool (L_student+stool), which is equal to zero.
L_initial = L_wheel + L_student+stool = 0
The angular momentum of an object is given by the product of its moment of inertia (I) and angular velocity (ω).
L = Iω
Let's denote the initial angular momentum of the wheel as L_wheel_initial, and the final angular momentum of the system as L_final.
L_wheel_initial = I_wheel * ω_wheel
The student and stool initially have zero angular velocity, so their initial angular momentum is zero:
L_student+stool_initial = 0
When the student holds the spinning wheel, the system starts to rotate. As a result, the wheel's angular momentum decreases, while the angular momentum of the student plus stool increases. However, the total angular momentum of the system remains conserved:
L_final = L_wheel_final + L_student+stool_final
Since the student and stool are initially at rest, their final angular momentum is given by:
L_student+stool_final = I_student+stool * ω_final
We can now set up the equation for the conservation of angular momentum:
L_wheel_initial + L_student+stool_initial = L_wheel_final + L_student+stool_final
Since the initial angular momentum is zero for the student and stool:
L_wheel_initial = L_wheel_final + L_student+stool_final
Substituting the expressions for angular momentum:
I_wheel * ω_wheel = I_wheel * ω_final + I_student+stool * ω_final
Now, we can solve for the final angular velocity (ω_final):
I_wheel * ω_wheel = (I_wheel + I_student+stool) * ω_final
ω_final = (I_wheel * ω_wheel) / (I_wheel + I_student+stool)
Now you can substitute the given values (I_wheel = 0.130 kg · m^2, ω_wheel = 16.1 rad/s, I_student+stool = 3.30 kg · m^2) into the equation to find the final angular velocity (ω_final) of the system.
SO, therefore, the final angular velocity is 0.612 rad/s.
To learn more about velocity, refer below:
https://brainly.com/question/17127206
#SPJ11
A student holds a spinning bicycle wheel while sitting motionless on a stool that is free to rotate about a vertical axis through its center (see the figure below). The wheel spins with an angular speed of 16.1 rad/s and its initial angular momentum is directed up. The wheel's moment of inertia is 0.130 kg · m2 and the moment of inertia for the student plus stool is 3.30 kg · m2. Determine the angular speed of the system (wheel plus student plus stool) after the student turns the wheel over, changing its angular momentum direction to down, without exerting any other external forces on the system. Assume that the student and stool initially rotate with the wheel.
An L-R-C series circuit has L = 0.420 H , C = 2.50x10-5 F , and a resistance R. You may want to review (Pages 1008 - 1010). For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of An underdamped l-r-c series circuit.
When solving problems related to L-R-C series circuits, it is important to keep in mind the properties of each component and how they interact with each other. It is also important to understand the different damping regimes and how they affect the behavior of the circuit.
An L-R-C series circuit is a circuit that consists of an inductor, a capacitor, and a resistor, all connected in series. In this circuit, the values of the inductor, L, and the capacitor, C, are given, and the value of the resistor, R, needs to be determined. This can be done by using the formula for the resonant frequency of the circuit, which is given by f = 1/(2π√(LC)). By measuring the resonant frequency of the circuit and using this formula, the value of R can be calculated.
It is important to note that this circuit can be either overdamped, critically damped, or underdamped, depending on the value of R. In an underdamped circuit, the value of R is such that the circuit oscillates with a frequency that is slightly different from the resonant frequency. This can be observed as a decaying sinusoidal waveform.
You can learn more about circuits at: brainly.com/question/12608491
#SPJ11
the average earth–sun distance is 1.00 astronomical unit (au). at how many aus from the sun is the intensity of sunlight 1/64 the intensity at the earth?
The distance from the sun where the intensity of sunlight is 1/64th of the intensity at the earth is 8 astronomical units.
To calculate the distance from the sun where the intensity of sunlight is 1/64th of the intensity at the earth, we can use the inverse square law of radiation. This law states that the intensity of radiation is inversely proportional to the square of the distance from the source.
Therefore, we can set up the equation:
(1/64) * Iearth = Isun at distance x from the sun
Where Iearth is the intensity of sunlight at the earth and Isun is the intensity of sunlight at a distance x from the sun.
Using the inverse square law, we can write:
Isun at distance x = Iearth * (1 au / x)^2
Substituting this expression into our equation above, we get:
(1/64) * Iearth = Iearth * (1 au / x)^2
Simplifying, we get:
x^2 = 64 au^2
Taking the square root of both sides, we get:
x = 8 au
Therefore, the distance from the sun where the intensity of sunlight is 1/64th of the intensity at the earth is 8 astronomical units.
learn more about distance
https://brainly.com/question/12577966
#SPJ11
A periodic signal is the summation of sinusoids of 5000 Hz, 2300 Hz and 3400 Hz Determine the signal's Nyquist frequency and an appropriate sampling frequency a. The signal's Nyquist frequency is ___ HZ
The signal's Nyquist frequency is 5000 Hz, and an appropriate sampling frequency would be 10,000 Hz or higher.
A periodic signal is a signal that repeats itself after a fixed interval of time. In this case, the periodic signal is composed of sinusoids with frequencies of 5000 Hz, 2300 Hz, and 3400 Hz. To determine the signal's Nyquist frequency, we need to identify the highest frequency component, which is 5000 Hz. The Nyquist frequency is the minimum rate at which a signal must be sampled in order to accurately represent the original signal without aliasing. This is given by the Nyquist-Shannon sampling theorem, which states that the sampling frequency must be at least twice the highest frequency component in the signal.
In this case, the appropriate sampling frequency would be at least twice the Nyquist frequency, which is 2 * 5000 Hz = 10,000 Hz. By choosing a sampling frequency of 10,000 Hz or higher, the signal can be accurately represented and reconstructed without any loss of information.
To know more about the Nyquist frequency, click here;
https://brainly.com/question/31392077
#SPJ11
what is the frequency of light when the energy for a mole of photons is 1.55 × 1013 j?
The frequency of light when the energy for a mole of photons is 1.55 x 10¹³ J is 3.89 x 10²² Hz.
Frequency of light refers to the number of complete oscillations or cycles of an electromagnetic wave that occur in one second. It represents the rate at which the waves oscillate and is measured in units of hertz (Hz).
In the context of light, frequency determines the color or wavelength of the electromagnetic radiation. Different colors of light correspond to different frequencies within the electromagnetic spectrum. For example, red light has a lower frequency compared to blue light.
Frequency is inversely related to the wavelength of light. As the frequency increases, the wavelength decreases, and vice versa. This relationship is described by the equation:
c = λν
where c is the speed of light, λ is the wavelength, and ν is the frequency. The frequency of light plays a crucial role in various phenomena, including the interaction of light with matter, the absorption and emission of light by atoms, and the perception of different colors by our eyes.
The relationship between energy (E) and frequency (ν) given by Planck's equation:
E = hν
where h is Planck's constant (6.626 x 10⁻³⁴ J·s).
Given that the energy for a mole of photons is 1.55 x 10¹³ J.
Since a mole of any substance contains Avogadro's number of entities (6.022 x 10^23), the energy per photon can be calculated by dividing the total energy by Avogadro's number:
Energy per photon = (1.55 x 10¹³ J) / (6.022 x 10²³) = 2.57 x 10⁻¹¹ J
2.57 x 10⁻¹¹ J = (6.626 x 10⁻³⁴ J·s) ν
ν = (2.57 x 10⁻¹¹ J) / (6.626 x 10⁻³⁴ J·s)
= 3.89 x 10²² Hz
Learn more about Frequency of light, here:
https://brainly.com/question/10732947
#SPJ12
a passive satellite differs from an active satellite in that a passive satellite: group of answer choices detects the smallest distance between two adjacent features in an image. detects the wavelength intervals, also called bands, within the electromagnetic spectrum. seldom detects the wavelength intervals, also called bands, within the electromagnetic spectrum. detects the reflected or emitted electromagnetic radiation from artificial sources. detects the reflected or emitted electromagnetic radiation from natural sources.
A passive satellite differs from an active satellite in that a passive satellite detects the reflected or emitted electromagnetic radiation from natural sources, while an active satellite emits its own signals and receives the reflected signals to obtain information.
A passive satellite differs from an active satellite in that a passive satellite detects the reflected or emitted electromagnetic radiation from natural sources. This is in contrast to an active satellite, which emits its own signal and then detects the reflection, allowing for greater control and precision. Passive satellites typically detect the wavelength intervals, also called bands, within the electromagnetic spectrum, and can be used to monitor natural phenomena such as weather patterns or changes in vegetation. They do not, however, detect the smallest distance between two adjacent features in an image, which is a function of the resolution of the satellite's sensors.
Learn more about electromagnetic radiation here :-
https://brainly.com/question/29646884
#SPJ11
if all of the energy from the annihilation were carried away by two gamma ray photons, what would be the wavelength of the photons?
The wavelength of each gamma ray photon would be 1.22 x 10⁻¹¹ meters.
We need to use the equation E = hc/λ, where E is the energy of the gamma ray photon, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon.
The total energy from the annihilation is given by E = mc², where m is the mass of the particle and antiparticle that annihilated each other. Since the question doesn't specify which particles were involved in the annihilation, we can't calculate m directly. However, we do know that all of the energy was carried away by two gamma ray photons.
Therefore, we can say that each photon has an energy of E/2. Plugging this into the equation above, we get:
E/2 = hc/λ
Rearranging, we get:
λ = 2hc/E
To calculate the wavelength, we need to know the energy of the photons. If we assume that the annihilation involved an electron and positron (the most common type of annihilation), then m = 9.11 x 10⁻³¹ kg (the mass of an electron), and E = 2mc² = 1.02 x 10⁻¹³ J.
Plugging this into the equation above, we get:
λ = 2hc/E = 2 x 6.63 x 10⁻³⁴ J s x 3 x 10⁸ m/s / 1.02 x 10⁻¹³J = 1.22 x 10⁻¹¹ m
Therefore, the wavelength of each gamma ray photon would be 1.22 x 10⁻¹¹ meters.
To know more about wavelength, refer
https://brainly.com/question/10750459
#SPJ11
If a compound contains 6. 87g of iron and
13. 1g of chlorine, what is the percent
composition of iron in this compound?
The percent composition of iron in the compound is 34.41%. To calculate the percent composition, we need to determine the mass of iron relative to the total mass of the compound.
The total mass of the compound is obtained by adding the masses of iron and chlorine together: 6.87g (iron) + 13.1g (chlorine) = 19.97g (total mass).
Next, we calculate the percent composition of iron by dividing the mass of iron by the total mass of the compound and multiplying by 100:
[tex]\[\frac{{6.87g}}{{19.97g}} \times 100 = 34.41\%\][/tex]
Therefore, the compound contains 34.41% iron.
This means that out of the total mass of the compound, 34.41% of it is due to iron. In other words, if you were to take 100 grams of the compound, 34.41 grams of it would be iron. The percent composition is a useful concept in chemistry as it helps us understand the relative proportions of elements within a compound.
To learn more about mass refer:
https://brainly.com/question/86444
#SPJ11
Describe the effects of taking the mass of the meterstick into account when the balancing position is not near the 500-cm position.
When determining the balancing position of a meterstick, it is important to take into account the mass of the meterstick itself. This is because the mass of the meterstick can have a significant impact on the position at which the stick balances.
If the balancing position is not near the 500-cm mark, taking the mass of the meterstick into account can cause the balancing position to shift. This is because the center of mass of the meterstick will be located at a different point than the 500-cm mark.As a result, the balancing position will be affected by the distance of the center of mass from the 500-cm mark. This can lead to a shift in the balancing position and make it more difficult to accurately determine the center of mass of the object being measured.
To account for the mass of the meterstick, it is important to consider the location of the center of mass and adjust the balancing position accordingly. This can be done by either physically shifting the position of the meterstick or by using mathematical calculations to adjust the balancing position.Overall, taking the mass of the meterstick into account is essential for accurately measuring the center of mass of an object and ensuring that the balancing position is accurately determined.
For more such questions on balancing
https://brainly.com/question/11904811
#SPJ11
When taking the mass of the meterstick into account, the balancing position of the meterstick will shift away from the center of the stick.
This means that the balancing position will no longer be at the 500-cm position, but will instead be located at a different point along the length of the meterstick. This shift in the balancing position will affect the accuracy of any measurements taken using the meterstick, as the weight distribution of the stick will not be evenly distributed. As a result, any calculations based on the position of the balancing point will need to take into account the mass of the meterstick, in order to ensure that the measurements are as accurate as possible.
When describing the effects of taking the mass of the meterstick into account when the balancing position is not near the 50-cm position (assuming you meant 50-cm as metersticks are usually 100-cm long), consider the following steps:
1. When the balancing position is not near the 50-cm position, it means the meterstick is not evenly balanced, and one side is heavier than the other.
2. If you don't take the mass of the meterstick into account, you might assume that the meterstick is uniformly distributed, and the balance point should be at the 50-cm position.
3. By considering the mass of the meterstick, you acknowledge that the weight distribution may not be uniform, and the balancing position may differ from the 50-cm mark.
4. Taking the mass into account allows you to more accurately calculate the mass and weight distribution of the meterstick and any attached objects.
5. As a result, you can determine the true center of mass and ensure that any measurements or calculations related to the meterstick are accurate.
In conclusion, taking the mass of the meterstick into account when the balancing position is not near the 50-cm position allows for a more accurate representation of the weight distribution, ensuring correct calculations and measurements.
Visit here to learn more about meterstick:
brainly.com/question/29690562
#SPJ11
The thoracic cavity before and during inspiration pogil
During inspiration, the thoracic cavity undergoes specific changes to facilitate the intake of air into the lungs. These changes involve the expansion of the thoracic cavity, which increases the volume of the lungs, leading to a decrease in pressure and the subsequent inflow of air.
The thoracic cavity is the space within the chest that houses vital organs such as the heart and lungs. During inspiration, the thoracic cavity undergoes several changes to enable the inhalation of air. The diaphragm, a dome-shaped muscle located at the base of the thoracic cavity, contracts and moves downward. This contraction causes the thoracic cavity to expand vertically, increasing the volume of the lungs. Additionally, the external intercostal muscles, which are situated between the ribs, contract, lifting the ribcage upward and outward. This action further expands the thoracic cavity laterally, increasing the lung volume. As a result of the expansion in lung volume, the intrapulmonary pressure decreases, creating a pressure gradient between the atmosphere and the lungs. Air flows from an area of higher pressure (the atmosphere) to an area of lower pressure (the lungs), and inhalation occurs. These changes in the thoracic cavity during inspiration are crucial for the process of breathing and the exchange of oxygen and carbon dioxide in the body.
To learn more about pressure refer;
https://brainly.com/question/28012687
#SPJ11
Light is incident upon two polarizing filters arranged in tandem. The filters are crossed so that their polarization directions are perpendicular. The transmitted intensity through the second filter
Answers: is 100%
depends on the frequency of the incident light.
depends on the intensity of the incident light.
is zero.
The transmitted intensity through the second filter is zero.
When polarized light passes through a polarizing filter, only the component of the electric field vector that is parallel to the filter's polarization direction is transmitted. When this already polarized light then passes through a second filter with a perpendicular polarization direction, none of the light is able to pass through, resulting in a transmitted intensity of zero.
In this scenario, the second filter is crossed with respect to the first filter, so the transmitted intensity through the second filter is zero. It does not depend on the frequency or intensity of the incident light.
To know more about intensity, visit;
https://brainly.com/question/17062836
#SPJ11
A thin, horizontal, 20-cm-diameter copper plate is charged to 4.0 nC . Assume that the electrons are uniformly distributed on the surfacea) What is the strength of the electric field 0.1 mm above the center of the top surface of the plate?b) What is the direction of the electric field 0.1 mm above the center of the top surface of the plate? (Away or toward)c) What is the strength of the electric field at the plate's center of mass?d) What is the strength of the electric field 0.1 mm below the center of the bottom surface of the plate?e) What is the direction of the electric field 0.1 mm below the center of the bottom surface of the plate? (Away or toward plate)
A charged copper plate has a 4.0 nC charge. Electric field strength and direction are calculated at different points.
A thin, horizontal, 20-cm-diameter copper plate with a 4.0 nC charge has uniform electron distribution on its surface. The electric field strength 0.1 mm above the center of the top surface of the plate can be calculated using the equation E = kQ / [tex]r^2[/tex] where k is Coulomb's constant, Q is the charge, and r is the distance.
Plugging in the values,
we get E = (9 x [tex]10^9[/tex] [tex]Nm^2[/tex]/[tex]C^2[/tex]) x (4.0 x [tex]10^-^9[/tex]C) / (0.1 x [tex]10^-^3[/tex] [tex]m)^2[/tex] = 1.44 x [tex]10^6[/tex] N/C.
The direction of the electric field is away from the plate. The electric field strength at the plate's center of mass is zero.
The electric field strength 0.1 mm below the center of the bottom surface of the plate can also be calculated using the same equation,
resulting in a value of 1.44 x [tex]10^6[/tex]N/C.
The direction of the electric field is toward the plate.
For more such questions on strength, click on:
https://brainly.com/question/8864435
#SPJ11
steam enters an adiabatic turbine at 10 and 1000° and leaves at a pressure of 4 . determine the work output of the turbine per unit mass of steam if the process is reversible.
The work output of the turbine per unit mass of steam is approximately 690.9 kJ/kg if the process is reversible.
Based on the given information, we can use the formula for reversible adiabatic work in a turbine:
W = C_p * (T_1 - T_2)
Where W is the work output per unit mass of steam, C_p is the specific heat capacity of steam at constant pressure, T_1 is the initial temperature of the steam, and T_2 is the final temperature of the steam.
First, we need to find the final temperature of the steam. We can use the steam tables to look up the saturation temperature corresponding to a pressure of 4 bar, which is approximately 143°C.
Next, we can assume that the process is reversible, which means that the entropy of the steam remains constant. Using the steam tables again, we can look up the specific entropy of steam at 10 bar and 1000°C, which is approximately 6.703 kJ/kg-K. We can then use the specific entropy and the final temperature of 143°C to find the initial temperature of the steam using the formula:
s_2 = s_1
6.703 = C_p * ln(T_1/143)
T_1 = 1000 * e^(6.703/C_p)
We can then use this initial temperature and the formula for reversible adiabatic work to find the work output per unit mass of steam:
W = C_p * (T_1 - T_2)
W = C_p * (1000 - T_2) * (1 - (T_2/1000)^(gamma-1)/gamma)
Where gamma is the ratio of specific heats for steam, which is approximately 1.3. Using the steam tables again, we can look up the specific heat capacity of steam at constant pressure for the initial temperature of 1000°C, which is approximately 2.53 kJ/kg-K.
Plugging in the values, we get:
W = 2.53 * (1000 - 143) * (1 - (143/1000)^(1.3-1)/1.3)
W = 690.9 kJ/kg
Therefore, the work output of the turbine per unit mass of steam is approximately 690.9 kJ/kg if the process is reversible.
Learn more about "work": https://brainly.com/question/25573309
#SPJ11
determine the phase constant ϕ ( −π≤ϕ≤π ) in x=acos(ωt ϕ) if, at t=0 , the oscillating mass is at x=−a .
The phase constant ϕ in x = Acos(ωt + ϕ) when x = -a at t = 0, we use ϕ = arccos(-a/A) or ϕ = -arccos(-a/A) depending on the value of arccos(-a/A).
Phase constant ϕThe equation for the position of an object undergoing simple harmonic motion is given by:
x = A cos(ωt + ϕ)
where
x is the position of the object, A is the amplitude of the motion, ω is the angular frequency, t is time, and ϕ is the phase constant.In this case, we are given that x = -a when t = 0. Plugging these values into the equation above, we get:
a = A cos(0 + ϕ)
Since the cosine of 0 is 1, this simplifies to:
a = A cos(ϕ)
To solve for the phase constant ϕ, we need to rearrange this equation and take the inverse cosine (also called the arccosine) of both sides:
cos(ϕ) = -a/A
ϕ = arccos(-a/A)
Note that the arccosine function only returns values between 0 and π, so to satisfy the given condition that −π ≤ ϕ ≤ π, we must consider two cases:
Case 1: arccos(-a/A) is between 0 and π.
In this case, the phase constant is simply:
ϕ = arccos(-a/A)
Case 2: arccos(-a/A) is between π and 2π.
In this case, the phase constant is:
ϕ = -arccos(-a/A)
Note that the negative sign here ensures that ϕ is still between −π and π.
So depending on the value of arccos(-a/A), we can determine the phase constant ϕ.
Learn more about phase constant ϕ: brainly.com/question/18369414
#SPJ11
How large is the duct required to carry 20,000 CFM of air if the velocity is not to exceed 1600 ft/min? Calculate the lost pressure due to air velocity in this duct. What is the equivalent rectangular duct with equal friction and capacity if one side is 26 in?
To carry 20,000 CFM of air without exceeding a velocity of 1600 ft/min, a duct with a cross-sectional area of 4.82 square feet is required. The pressure drop due to air velocity in this duct is 0.0085 inches of water. The equivalent rectangular duct with equal friction and capacity if one side is 26 inches is approximately 13.61 inches by 26 inches.
To determine the size of the duct required to carry 20,000 CFM of air, we need to calculate the cross-sectional area of the duct. First, we convert the velocity limit of 1600 ft/min to feet per second by dividing it by 60. This gives us 26.67 ft/s. Then, we can use the formula A = CFM / (Velocity * 144) to find the cross-sectional area, where A is in square feet, CFM is the flow rate in cubic feet per minute, and Velocity is in feet per second. Plugging in the values, we get A = 20000 / (26.67 * 144) = 4.82 square feet.
Next, we need to calculate the pressure drop due to air velocity in the duct. This can be done using the formula ΔP = 0.109 * (Velocity / 4005) ^ 2 * (Density * Length), where ΔP is the pressure drop in inches of water, Velocity is in feet per second, Density is the air density in pounds per cubic foot, and Length is the length of the duct in feet. Assuming standard air conditions of 70°F and 29.92 inches of mercury pressure, the air density is 0.075 pounds per cubic foot. Let's assume a duct length of 100 feet. Plugging in the values, we get ΔP = 0.109 * (26.67 / 4005) ^ 2 * (0.075 * 100) = 0.0085 inches of water.
Finally, we need to find the equivalent rectangular duct with equal friction and capacity if one side is 26 inches. The equivalent rectangular duct can be calculated using the formula A = (2 * B + H) * H, where A is the cross-sectional area of the duct, B is the smaller side of the rectangular duct, and H is the larger side. Solving for H, we get H = (-2B ± sqrt(4B^2 + 4A)) / 2. Let's assume B is 26 inches. Plugging in the values, we get H = (-2 * 26 ± sqrt(4 * 26^2 + 4 * 4.82)) / 2. Solving for H, we get H = 13.61 inches or H = -39.61 inches (which is extraneous). Therefore, the equivalent rectangular duct with equal friction and capacity is approximately 13.61 inches by 26 inches.
In conclusion, to carry 20,000 CFM of air without exceeding a velocity of 1600 ft/min, a duct with a cross-sectional area of 4.82 square feet is required. The pressure drop due to air velocity in this duct is 0.0085 inches of water. The equivalent rectangular duct with equal friction and capacity if one side is 26 inches is approximately 13.61 inches by 26 inches.
To know more about velocity visit :
https://brainly.com/question/30546049
#SPJ11
In Part II of the lab ("Mass"), calculate an estimate of effect (error) the 1.0 m cord has on the T of the swinging 50.0 g mass. Do this by calculating the net center of mass of the cord-hanging mass system, calculating the T using that L, and then comparing that new T to the original T you calculated ignoring the effect of the string on L. Show your work.
We can estimate the effect that the 1.0 m cord has on the T of the swinging 50.0 g mass by calculating the net center of mass of the cord-hanging mass system, calculating the T using the new L, and comparing it to the original T.
To calculate the estimate of effect that the 1.0 m cord has on the T of the swinging 50.0 g mass, we need to first calculate the net center of mass of the cord-hanging mass system.
We know that the mass of the hanging mass is 50.0 g, and the length of the cord is 1.0 m. Therefore, the total mass of the system is 50.0 g + (mass of cord). Since the mass of the cord is negligible compared to the hanging mass, we can assume that the total mass of the system is approximately 50.0 g.
To find the net center of mass, we need to find the midpoint of the cord. Since the cord is straight and hangs vertically, the midpoint will be at a distance of 0.5 m from the point of suspension.
Now, we can calculate the T using the new L (which is the distance between the point of suspension and the midpoint of the cord). We can use the formula T = 2π√(L/g), where g is the acceleration due to gravity. Plugging in the values, we get T = 2π√(0.5/9.8) = 0.71 s.
Finally, we can compare this new T to the original T we calculated ignoring the effect of the string on L. If the difference is significant, it means that the cord has an effect on the T of the hanging mass.
To know more about string visit:
brainly.com/question/29825205
#SPJ11
a system of particles is known to have a positive total kinetic energy. what can you say about the total momentum of the system?
If the total kinetic energy of a system of particles is positive, it suggests that the system has a non-zero total momentum.
In a system of particles, if the total kinetic energy is positive, it implies that the particles within the system are in motion. The total momentum of the system depends on the individual momenta of the particles and their respective masses.
Since the kinetic energy is positive, it indicates that the particles have non-zero velocities. In order for the total momentum to also be positive, the velocities of the particles must have a net direction. This means that the particles are either moving collectively in the same direction or their individual velocities are such that the sum of their momenta is positive.
In summary, if the total kinetic energy of a system of particles is positive, it suggests that the system has a non-zero total momentum, which indicates either a collective motion in the same direction or a combination of individual velocities that result in a positive net momentum.
To know more about total momentum here
https://brainly.com/question/29112551
#SPJ4
An ideal gas expands isothermally along AB and does 700
J
of work. How much heat does the gas exchange along AB? The gas then expands adiabarically along BC and does 400
J
of work. When the gas returns to A along CA, it exhausts 100
J
of heat to the surroundings. How much work is done on the gas along this path?
Ideal gas is a theoretical gas that is composed of a large number of identical particles (such as atoms or molecules) that are in constant random motion. The particles of an ideal gas are assumed to have no volume, and to exert no attractive or repulsive forces on each other, except during collisions.
For an isothermal expansion of an ideal gas, the heat exchanged can be calculated using the following formula:Q = W
where Q is the heat exchanged, and W is the work done by the gas. Therefore, for the isothermal expansion along AB:Q_AB = 700 J
For an adiabatic expansion of an ideal gas, the following relationship holds:PV^γ = constant
where P is the pressure, V is the volume, and γ is the ratio of the specific heats of the gas. For an adiabatic process, no heat is exchanged with the surroundings, so Q = 0. Using the above relationship, we can write:P_BV_B^γ = P_CV_C^γ
Since the gas returns to its initial state, we can write:P_AV_A = P_CV_C^γ
Combining these equations, we get:V_C/V_B = (P_B/P_C)^1/γ
V_A/V_C = (P_C/P_A)^1/γ
Multiplying these equations, we get:V_A/V_B = (P_B/P_A)^1/γ
Using the ideal gas law, we can write:P_BV_B/T = P_AV_A/T
Combining this with the above equation, we get:V_A/V_B = (T_B/T_A)
Using the above relationships, we can calculate the volume ratios as follows:V_C/V_B = (P_B/P_C)^1/γ = (2/1)^1.4 = 2.30
V_A/V_C = (P_C/P_A)^1/γ = (2/1)^1.4 = 2.30
V_A/V_B = (T_B/T_A) = 1
Now, we can use the following formula to calculate the work done on the gas during the return path CA:W_CA = Q_CA + ΔU
where Q_CA is the heat exchanged, ΔU is the change in internal energy of the gas. Since the gas returns to its initial state, the change in internal energy is zero. Therefore:W_CA = Q_CA = -100 J
(since heat is exhausted to the surroundings)
Putting all the values together, we get:Q_AB = 700 J (heat exchanged along AB)
Q_BC = 0 J (adiabatic expansion along BC)
Q_CA = -100 J (heat exhausted along CA)
W_CA = Q_CA + ΔU = -100 J (work done on the gas along CA)
For such more questions on ideal gas
https://brainly.com/question/24236411
#SPJ11
consider a series rlc circuit where the resistance =549 ω , the capacitance =3.25 μf , and the inductance =45.0 mh . determine the resonance frequency 0 of the circuit. 0=ω0=rad/srad/sWhat is the maximum current maxImax when the circuit is at resonance, if the amplitude of the AC driving voltage is 36.0 V36.0 V?
The resonance frequency of the circuit is approximately 2.51 x 10^3 rad/s, and the maximum current in the circuit at resonance is approximately 0.0655 A.
The resonance frequency of the RLC circuit can be calculated using the formula:
ω0 = 1/√(LC)
where L is the inductance in henries and C is the capacitance in farads. Substituting the given values, we get:
ω0 = 1/√[(45.0 x 10^-3 H)(3.25 x 10^-6 F)] ≈ 2.51 x 10^3 rad/s
The maximum current in the circuit at resonance can be calculated using the formula:
Imax = Vmax/Z
where Vmax is the amplitude of the AC driving voltage and Z is the impedance of the circuit at resonance. The impedance of the RLC circuit at resonance is equal to the resistance, since the reactances of the inductor and capacitor cancel each other out. Therefore, we have:
Z = R = 549
Substituting the given values, we get:
Imax = (36.0 V)/(549 Ω) ≈ 0.0655 A
For more question on resonance frequency click on
https://brainly.com/question/29893340
#SPJ11
To determine the resonance frequency (ω₀) of a series RLC circuit and the maximum current (I_max) at resonance, follow these steps:
Step 1: Identify the given values.
Resistance (R) = 549 Ω
Capacitance (C) = 3.25 μF = 3.25 × 10⁻⁶ F
Inductance (L) = 45.0 mH = 45.0 × 10⁻³ H
Amplitude of the AC driving voltage (V₀) = 36.0 V
Step 2: Calculate the resonance frequency (ω₀).
ω₀ = 1 / √(LC)
ω₀ = 1 / √((45.0 × 10⁻³ H)(3.25 × 10⁻⁶ F))
ω₀ ≈ 310.24 rad/s
Step 3: Calculate the impedance (Z) at resonance.
At resonance, the impedance is equal to the resistance since the inductive and capacitive reactances cancel each other out:
Z = R = 549 Ω
Step 4: Calculate the maximum current (I_max) at resonance.
I_max = V₀ / Z
I_max = 36.0 V / 549 Ω
I_max ≈ 0.0656 A
At resonance, the frequency is approximately 310.24 rad/s, and the maximum current is approximately 0.0656 A.
Learn more about resonance frequency here : brainly.com/question/28168823
#SPJ11
For the part shown, answer the following questions with regard to the cylindrical boss. (a) What are the maximum and minimum diameters allowed for the boss? (b) What is the effect of the position tolerance of 0.2 on the diameters specified in part (a)? (c) The position control defines a tolerance zone. Specifically what must stay within that tolerance zone? (d) What is the diameter of the tolerance zone if the boss is produced with a diameter of 50.3? (e) What is the diameter of the tolerance zone if the boss is produced with a diameter of 49.7? (f) Describe the significance of the datum references to the determination of the position tolerance zone.
a) The maximum allowed diameter for the boss is 30.1 mm and the minimum allowed diameter is 29.9 mm.
b) The position tolerance of 0.2 mm will affect the range of allowable diameters, making the maximum diameter 30.3 mm and the minimum diameter 29.7 mm.
c) The cylindrical boss must stay within the tolerance zone defined by the position control, which is a cylinder with a diameter of 30.1 mm and a height equal to the distance between the two datum planes.
d) If the boss is produced with a diameter of 50.3 mm, the diameter of the tolerance zone is 0.2 mm larger than the diameter of the boss, which is 50.5 mm.
e) If the boss is produced with a diameter of 49.7 mm, the diameter of the tolerance zone is 0.2 mm larger than the diameter of the boss, which is 49.9 mm.
f) The datum references provide the basis for the position tolerance zone. They define the three mutually perpendicular planes which control the location and orientation of the cylindrical boss. Without the datum references, the position tolerance zone would be undefined or difficult to determine.
The given drawing shows a cylindrical boss with specified dimensions and tolerances. The position tolerance control defines a tolerance zone, which is a cylinder with a diameter of 30.1 mm and a height equal to the distance between the two datum planes. The cylindrical boss must stay within this tolerance zone to be considered acceptable.
(a) The maximum and minimum diameters allowed for the boss are specified as 30.1 mm +0.2 mm and 29.9 mm -0.2 mm, respectively.
(b) The position tolerance of 0.2 mm will affect the allowable range of diameters, making the maximum diameter 30.3 mm and the minimum diameter 29.7 mm.
(c) The position control defines a tolerance zone within which the cylindrical boss must stay. The cylindrical boss must be located and oriented according to the three mutually perpendicular datum planes specified on the drawing.
(d) If the boss is produced with a diameter of 50.3 mm, the diameter of the tolerance zone is 0.2 mm larger than the diameter of the boss, which is 50.5 mm.
(e) If the boss is produced with a diameter of 49.7 mm, the diameter of the tolerance zone is 0.2 mm larger than the diameter of the boss, which is 49.9 mm.
(f) The datum references provide the basis for the position tolerance zone. They define the three mutually perpendicular planes which control the location and orientation of the cylindrical boss. Without the datum references, the position tolerance zone would be undefined or difficult to determine.
To learn more about tolerance zone, here
https://brainly.com/question/30188931
#SPJ4
determine the wavelength of a musical note with a frequency of 1,248 hz. hint: what is the speed of sound in air?
Therefore, the wavelength of a musical note with a frequency of 1,248 Hz is approximately 0.275 meters.
The speed of sound in air depends on several factors, including temperature, humidity, and atmospheric pressure. At standard temperature and pressure (STP), which is 0 °C and 1 atm, the speed of sound in dry air is approximately 343 meters per second (m/s).
To determine the wavelength of a musical note with a frequency of 1,248 Hz, we can use the formula:
wavelength = speed of sound / frequency
Substituting the values, we get:
wavelength = 343 m/s / 1248 Hz
wavelength ≈ 0.275 meters
To know more about wavelength,
https://brainly.com/question/31143857
#SPJ11