A kangaroo is capable of jumping to a height of 2.62m. Determine the takeoff speed of the kangaroo.

a) The magnetic field at the center of loop 20.0 cm in diameter carrying is equals to the 2.8274×10⁻⁵ T.

b) Smallest magnetic field that change measured value by 0.0100% is equals to the 2.8274×10⁻⁹ T.

We know that moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths. Consider the wire segment present in above figure.

A) Diameter of wire segment, d = 20 cm or 0.2 m carrying current I = 4.5 A

Magnetic Field at the center of current loop of segment, B= μ₀I/d

= 4π×10⁻⁷×4.5/0.2

= 2.8274×10⁻⁵ T

Therefore magnetic Field at the center of current loop 2.8274×10⁻⁵ T.

B) Current in carrying wire, I = 4.5 A

The field should be less than the measured field by 0.0100%. So, smallest field that change measured value by 0.0100% = 0.0100% of 2.8274×10⁻⁵ T

= 2.8274×10⁻⁹ T

Therefore Smallest field that change measured value by 0.0100% = 2.8274×10⁻⁹ T

For more information about magnetic field, visit :

https://brainly.com/question/26257705

#SPJ4

Complete question:

The above figure completes the question.

Since moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths often affect the system they are being used to measure. Consider the wire segment in the figure, which is used to measure the magnetic field by determining the foree exerted on the current flowing through it. Part (a) Estimate the field the loop creates by calculating the field strength, in teslas, at the center of a circular loop 20.0 cm in diameter carrying

Part (b) What is the smallest field strength this loop can be used to measure with a 4.5 -A current, if its field should alter the measured field by 0.0100% or less?

Answer:

-7,942.2 Newtons

Explanation:

Car Force Calculation.

How much force would you exert if your car weighs 1,302 and your acceleration rate is -6.1 m/s

To calculate the force exerted by a car, we can use the formula:

force = mass x acceleration

where mass is the mass of the car in kilograms, and acceleration is the acceleration rate in meters per second squared (m/s^2).

Given that the car weighs 1,302 kg and the acceleration rate is -6.1 m/s^2, we can plug these values into the formula:

force = 1,302 kg x (-6.1 m/s^2)

force = -7,942.2 Newtons (N)

The negative sign indicates that the force is in the opposite direction of the acceleration, which in this case is towards the back of the car.

A) Velocity of the space capsule after the push in the reference frame= - 0.042 m/s .B) Magnitude of the average force exerted by each on the other= 462 N.C) Kinetic energy of the astronaut after the push in the reference frame= 614 J. D) Kinetic energy of the capsule after the push in the reference frame= 22.8 J

Explanation:Given dataMass of astronaut= 135 kgSpeed of astronaut= 2.70 m/sMass of space capsule= 1900 kgTime taken by astronaut to acquire speed= 0.66 secondsWe have to find- the velocity of the space capsule after the push in the reference frame- the magnitude of the average force exerted by each on the other- the kinetic energy of the astronaut after the push in the reference frame- the kinetic energy of the capsule after the push in the reference frameThe first step is to use conservation of momentum to find the velocity of the space capsule after the push in the reference frame.Conservation of momentum Initial momentum= Final momentum(1900 kg) (0 m/s) = (1900 kg + 135 kg) (v)V = -0.042 m/sThis negative sign indicates that the space capsule moves backward. A) Velocity of the space capsule after the push in the reference frame= - 0.042 m/sThe second step is to use the impulse-momentum theorem to find the average force exerted by each on the other. Impulse= change in momentum .We have the initial and final momenta from the conservation of momentum.Velocity before push= 0Velocity after push= -0.042 m/sImpulse= mΔv= (1900+135)(-0.042-0)NΔt= Impulse = Δp = 1900.042/0.66N= 462 NC) Magnitude of the average force exerted by each on the other= 462 NThe third step is to find the kinetic energy of the astronaut after the push in the reference frame.Kinetic energy= ½ mv²Kinetic energy of astronaut= ½ (135) (2.70)²J= 614 JD) Kinetic energy of the capsule after the push in the reference frame.Kinetic energy of space capsule= ½ (1900) (-0.042)²J= 22.8 J.

for more such questions on Velocity

https://brainly.com/question/10425898

#SPJ11

The electric field intensity at the same point due to the two point charges is -4.13e5 N/C.

Electric force is the force experienced by a charged object placed in an electric field. The electric force formulation is sometimes confused with Coulomb's law, but the electric force is more general than Coulomb's law and applies only to two-point charges. 

The electric force on a 10 nC charge located at (0, 3, 1) due to the two point charges is given by:

F = (1e-7 N m²/C²) × [(1e-3 C) / (3² + 4² + 5²)³/2 + (-2e-3 C) / (8² + 8² + 9²)³/2]

F = -4.13e-5 N

The electric field intensity at the same point due to the two point charges is given by:

E = F / (10e-9 C)

E = -4.13e5 N/C

Learn more about the electric force: brainly.com/question/30236242

#SPJ11

The number of the different ways can be 4. The correct option is C.

The total resistance of four identical resistors in series is 4R, while the total resistance of four identical resistors in parallel is R. Therefore, there are two ways to connect the four resistors in order to achieve a total resistance of R: connecting them in series or connecting them in parallel.

(i) In the first way, we connect two pairs of resistors in series, and then, these pairs are connected in parallel.

(ii) In a second way, we connect two resistors in series, and then, this pair is connected in parallel with the other pair of resistors that are also connected in series.

(iii) In a third way, we connect three resistors in series and connect this combination in parallel with the remaining resistor.

(iv) In a fourth way, we connect all four resistors in series.

We need to connect four identical resistors of resistance R so that the equivalent resistance of the resulting combination is R. The number of ways we can do it is 4. So, the correct option is (C) 4.

To learn more about resistors follow

https://brainly.com/question/9629378

#SPJ11

1) The box slides 23.6 m before stopping.

2) The coefficient of friction is 0.600.

3)  If the friction coefficient had a constant value of 0.100, then the box would have slid a distance of 12.5 m

1)Using the work-energy theorem, we can find how far the box slides before it stops. The theorem states that the work done by all forces acting on the object is equal to the change in its kinetic energy, or:
W = ΔKE

Where W is the work done by all forces, and ΔKE is the change in kinetic energy. Since the work done by all forces is equal to the friction force, the work done by friction is equal to the change in kinetic energy. Therefore, the equation can be rewritten as:
Wfriction = ΔKE

In this situation, the friction force increases linearly with distance, so the work done by friction (Wfriction) is the integral of the friction force over the distance. The integral is equal to the area under the graph of friction force versus distance. Therefore, the equation can be rewritten as:
∫Ffriction(x)dx = ΔKE

The integral is equal to the area under the graph of friction force versus distance from 0 to the stopping point. Since the coefficient of friction increases linearly from 0.100 at P to 0.600 at 12.5 m past point P, we can calculate the stopping point using the equation:
0.100x + 0.500(x-12.5) = ΔKE

Solving the equation for x, we find that the box stops at x = 23.6 m.

2)At the stopping point, the coefficient of friction is 0.600.

3) This is because the integral of the friction force with a constant coefficient of 0.100 is equal to 0.100x, where x is the distance traveled.

for such more question on coefficient

https://brainly.com/question/29719172

#SPJ11

"The units appropriate for measurement of apparent brightness is watts per square metre."

Even though a flashlight that is close by might seem brighter than a streetlight that is far away, the flashlight is actually much less bright when contrasted side by side. The measurement of a star's luminosity—a fancy term for its real brightness—as seen from Earth is known as apparent brightness, also known as apparent magnitude.

The intensity of starlight that reaches us per unit area is known as apparent luminosity. Area is measured in square meters and power is measured in volts.

A photometer is a device that gauges and rates a celestial body's luminosity.

To know more about brightness:

https://brainly.com/question/13680972

#SPJ4

Astronomers can't measure the diameter of stars directly due to their vast distance and small apparent sizes. Indirect methods, such as studying brightness, temperature, and gravitational influence, are used instead.

Since stars are so far away from Earth and appear to be very small, astronomers are unable to directly estimate the diameters of stars. When seen via a telescope, even the greatest stars in our galaxy are only visible as tiny specks of light. It is also challenging to pinpoint the exact stellar borders since the light that stars generate is a complex mixture of wavelengths and intensities. To determine the sizes of stars, astronomers may, however, use a range of indirect techniques, including examining the brightness and temperature of the stars, their gravitational pull on surrounding objects, and the way their light is bent by their own atmospheres.

learn more about Astronomers  here:

https://brainly.com/question/14853303

#SPJ4

The correct option is A, the amplitude and period of the oscillations that result from this collision are 0.300 m in 1.26s.

The expression for Period of spring is,

[tex]T = 2\pi\sqrt{\frac{2m}{k} }[/tex]

Here, m is the mass of the spring and k is the spring constant

Substitute 2 kg

for m

and 100N/m

for k

in equation [tex]T = 2\pi\sqrt{\frac{2m}{k} }[/tex]

and solve for T .

[tex]T = 2\pi\sqrt{\frac{(2)2 kg}{100 N/m} }[/tex]

T = 1.26s

In physics, amplitude refers to the maximum displacement or distance moved by a wave from its equilibrium or mean position. It is a measure of the intensity or strength of a wave, and it is usually represented as the height of the crest or depth of the trough of the wave.

The amplitude of a wave can be measured in various units, depending on the type of wave and the context in which it is being studied. For example, the amplitude of a sound wave is measured in decibels (dB), while the amplitude of an electromagnetic wave is measured in volts per meter (V/m). Amplitude plays an important role in the behavior of waves. It determines the energy carried by the wave and affects other properties such as frequency, wavelength, and phase.

To learn more about Amplitude visit here:

brainly.com/question/8662436

#SPJ4

Complete Question: -

A 2.00-kg object is attached to an ideal massless horizontal spring of spring constant 100.0 N/m and is at rest on a frictionless horizontal table. The spring is aligned along the x-axis and is fixed to a peg in the table. Suddenly this mass is struck by another 2.00-kg object traveling along the x-axis at 3.00 m/s, and the two masses stick together. What are the amplitude and period of the oscillations that result from this collision

A) 0.300 m, 1.26 s

B) 0.300 m, 0.889 s

C) 0.424 m, 0.889 s

D) 0.424 m, 1.26 s

E) 0.424 m, 5.00 s

As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will increase.

What is Charge?

Charge is a fundamental property of matter that determines how objects interact with each other through the electromagnetic force. It is a physical property that can be positive or negative and can be measured in coulombs (C).

This is because the positively charged glass rod will induce a negative charge on the metal knob of the electroscope. The negative charges will repel the electrons in the metal leaves, causing them to move away from each other and increasing their separation. The greater the amount of charge on the glass rod, the greater the separation between the leaves will be.

Learn more about Charge from given link

https://brainly.com/question/18102056

#SPJ1

Answer:

6n

Explanation:

Given:

Force acting by student 1 = 10 N

Force acting by student 2 = 4 N

Find:

Net force acting on the board

Computation:

Net force acting on the board = Force acting by student 1 - Force acting by student 2

Net force acting on the board = 10 N - 2 N

Net force acting on the board = 6 N

The distance till which Rhoda should compress the spring to score a direct hit is 1.37 centimeters.

Rhoda needs to compress the spring by a distance of 1.37cm to score a direct hit. The equation to find this distance is: D = [tex][(x + y)^2 - x^2]^{(1/2)}[/tex]

where, D is the horizontal distance, x is the initial compression of the spring (1.7cm), and y is the additional compression needed to reach the target box (the unknown).

To solve for y, we can rearrange the equation as:

[tex]y = [(D^2 - x^2]^{(1/2)} - x\\[/tex]

Plugging in the values, we have

[tex]y = [(2.2^2 - (1.7)^2]^{(1/2)}[/tex]- 1.7 = 1.37cm

Therefore, Rhoda needs to compress the spring by 1.37 cm to score a direct hit.

Learn more about Spring here:

https://brainly.com/question/14670501

#SPJ11

Answer:

The light and heat of the sun are produced by the process of nuclear fusion, where hydrogen atoms combine to form helium, releasing vast amounts of energy in the process.

In a conservative system, the total energy is conserved, which means that the initial energy (ei) is equal to the final energy (ef).

Conservative systems are those where the total energy remains constant over time, such as in a pendulum swinging back and forth or a planet orbiting a star under the influence of gravity.

In such systems, the energy can be converted from one form to another, but the total amount of energy remains constant.

Therefore, we can say that in a conservative system, the initial energy (ei) and the final energy (ef) are equal. This means that any changes in the system's energy, such as potential energy being converted into kinetic energy, must be balanced by an equal and opposite change in some other form of energy, such as potential energy being converted into kinetic energy.

Learn more about conservation of energy here: https://brainly.com/question/166559

#SPJ1

The void in mineral aggregate (VMA) is -12.35%, the void in total mix (VTM) is 0.000990 and the voids filled with asphalt (VFA) is -12.35%.

To determine the VMA, VTM, and VFA neglecting absorption, we need to calculate the following:

[tex]VMA = [(Gmb - Gsb) / Gmb] \times 100[/tex]

[tex]VTM = Gmb / ρb[/tex]

[tex]VFA = [(Gmb - Ga) / Gmb] \times 100[/tex]

Where, Gmb = bulk specific gravity of the compacted specimen of HMA.

Gsb = bulk specific gravity of the aggregate in the HMA specimen.

ρb = bulk density of the HMA specimen

Ga = apparent specific gravity of the aggregate in the HMA specimen.

Substitute the given values we get:

[tex]Gmb = 2.435, Gsb = 2.735, \rho b = 2455\  kg/m^3[/tex],

[tex]Ga = (Gmb \times Gsa) / (5.1 + 0.049 (Gmb - 2.435)) = (2.435 \times 2.735) / (5.1 + 0.049 (2.435 - 2.435)) = 2.449[/tex]

By substituting these values in the above formula, we get:

[tex]VMA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%

[tex]VTM = 2.435 / 2455 = 0.000990[/tex]

[tex]VFA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%

Hence, VMA = -12.35%, VTM = 0.000990, VFA = -12.35%.

The minus sign indicates that the voids are insufficient. Therefore, the mix is unstable.

Learn more about specific gravity:

https://brainly.com/question/20422535

#SPJ11

In the comparison between these compounds, the bond is weaker due to the difference in electronegativity between the two atoms.

We can use the relation: E = hν

where, E is the energy of the photon, h is Planck's constant, and ν is the frequency of the photon.

Converting to Hz:

ν = 15376 MHz = 15376 × 106 Hz = 1.5376 × 10¹⁰ Hz

Substituting the frequency into the formula for photon energy: E = hν

E = 6.626 × 10⁻³⁴ J s × 1.5376 × 10¹⁰ Hz

E = 1.019 × 10⁻²³Joules

The frequency of the photon can be used to calculate the wavenumber, which in turn can be used to determine the internuclear distance of the molecule. The wavenumber (ν¯) of the photon is defined as the frequency divided by the speed of light, c:

ν¯= ν/c

where, c is 2.998 × 10⁸ m/s.

Converting the frequency into wavenumber:

ν¯= ν/c = 1.5376 × 10¹⁰ Hz/2.998 × 10⁸ m/s = 51.31 cm⁻¹

The wavenumber of the photon can be used to calculate the internuclear distance (r) by using the equation:

r = [h/(8π²cμ)]½ × (1/ν¯)

where, h is Planck's constant, c is the speed of light, and μ is the reduced mass of the molecule (m₁m₂/m₁ +m₂).

For K₃₅Cl₃₉, the atomic masses of K and Cl are 39 and 35, respectively. Therefore, m₁ = 39, u = 39 × 1.66 × 10⁻²⁷ kg = 6.474 × 10⁻²⁶ kg, m₂ = 35 u = 35 × 1.66 × 10⁻²⁷ kg = 5.81 × 10⁻²⁶ kg,

μ = (m₁m₂/m₁ +m₂) = 39 × 35/(39 + 35)

u = 16.86

u= 16.86 × 1.66 × 10⁻²⁷kg = 2.798 × 10⁻²⁶kg  

Substituting the values of the constants and the wavenumber: r = [h/(8π²cμ)]½ × (1/ν¯)r = [(6.626 × 10⁻³⁴ J s)/(8π² × 2.998 × 10⁸ m/s × 2.798 × 10⁻²⁶ kg)]½ × (1/51.31 cm⁻¹)r = 1.873 × 10⁻¹⁰ m = 1.873 Å

We can compare this bond length to that of HCl, which is 1.275 Å. The internuclear distance of K₃₅Cl₃₉ is much longer than that of HCl, indicating that the bond in K₃₅Cl₃₉ is weaker. This is consistent with the fact that K₃₅Cl₃₉ is a heteronuclear diatomic molecule, whereas HCl is a homonuclear diatomic molecule. In a heteronuclear diatomic molecule, the bond is weaker due to the difference in electronegativity between the two atoms.

Learn more about Electronegativity here:

https://brainly.com/question/17762711

#SPJ11

The amount of work required to push the box (mass 130 kg) up an incline (angle 20 degrees with the horizontal) that is 10 meters long, with the coefficient of kinetic friction being 0.5, is  25145.1 J.

The frictional force that acts on a body when it slides on a surface is referred to as kinetic friction or sliding friction. When a body slides across a surface, the force that opposes its motion is referred to as kinetic friction.Kinetic friction equationThe formula for kinetic friction can be written as follows:

F[tex]_k[/tex] = μk N

Where:

F[tex]_k[/tex] is the force of kinetic friction

N is the normal force

μk is the coefficient of kinetic friction

The force of kinetic friction is equivalent to the product of the normal force and the coefficient of kinetic friction. The normal force is equal to the weight of the object in this case, i.e., N = mg.

The force required to push the box up the incline can be calculated using the following formula:

W = mg(sin θ + μk cos θ)

Distance traveled by the box is 10 meters, so the work done to push the box up the incline is equal to

W = F.d

where,

F = force applied

d = distance moved by the box

W = 130 * 9.8 * (sin 20 + 0.5 cos 20) * 10

W = 25145.1 J

Therefore, it would take 25145.1 J of work to push a box.

Learn more about work at https://brainly.com/question/25573309

#SPJ11

If the magnetic field and the velocity are perpendicular, the force is maximum, and if they are parallel, the force is zero. The direction of the magnetic force can be determined using Fleming’s left-hand rule. The thumb represents the direction of the motion of the charge, the first finger represents the direction of the magnetic field, and the middle finger represents the direction of the magnetic force.

A square loop of wire carrying current in the counterclockwise direction will experience a force.

The force will be in the direction given by Fleming’s left-hand rule. The magnetic field is uniform and horizontal, and it is pointing towards the right. The question is asking for the direction of the net force on the loop. The direction of the net force on the loop can be determined using the right-hand palm rule.

The right-hand palm rule states that the thumb represents the direction of the current, and the fingers represent the direction of the magnetic field. If the fingers of the right hand are curled in the direction of the magnetic field and the thumb in the direction of the current, then the direction of the force is given by the palm.

In this case, the palm points upwards, which means that the net force on the loop is out of the screen. Therefore, the correct option is (A) out of the screen. Magnetic force The force exerted on a charged particle moving in a magnetic field is known as magnetic force. The direction of the magnetic force on the moving charge is perpendicular to the plane formed by the magnetic field and the velocity of the charge.

for such more questions on Magnetic force

https://brainly.com/question/29213676

#SPJ11

2hcosθsinθ is the distance R from the foot of the wall the emerging steam strike the floor.

the second hole should be cut at a height of (H - h/4) above the bottom of the tank in order to get the same range as the first hole.

Let's derive an expression for the velocity of water coming out of the hole. The water coming out of the hole is a free fall under gravity .

So we can use Bernoulli's equation to find the velocity of the water coming out of the hole as:
P + (1/2)ρv² + ρgh = constant ….(1)

where P is the pressure of the water inside the tank,

ρ is the density of water,

v is the velocity of the water coming out of the hole,

h is the height of the water level inside the tank, and g is the acceleration due to gravity.

Since the hole is below the water's surface, the pressure at the hole is the pressure due to water at the second hole should be cut at a height of (H - h/4) above the bottom of the tank in order to get the same range as for the first hole.

depth h. So, the pressure due to water is ρgh.

At the hole, the velocity of water is v, and the height of the water surface above the hole is (H - h). Therefore, the pressure at the surface of the water is ρg(H - h). Putting these values in equation (1), we get:

P + (1/2)ρv² + ρgh = ρg(H - h) + P₀

Where P₀ is atmospheric pressure, which can be considered constant. This is the Bernoulli's equation.
Let's apply the law of conservation of mechanical energy.
Let the velocity of the water coming out of the hole be v.

The kinetic energy of the water at the hole is (1/2)ρv².

The gravitational potential energy of the water at the hole is ρgh.

The gravitational potential energy of the water at the point where it hits the floor is zero.

Hence, by the law of conservation of mechanical energy, we can write:

(1/2)ρv² + ρgh = 0

Solving for v, we get:

v = √(2gh)

Part a) of the question:

We know the velocity of the water coming out of the hole. Let's assume that the stream coming out of the hole makes an angle of θ with the horizontal, as shown in the figure.

We need to find the horizontal distance R from the foot of the wall at which the stream hits the floor. This is given by:

R = (v²/g)sin2θ

sin2θ can be written as 2sinθcosθ. Therefore, we get:

R = (v²/g)sinθcosθ

Using the value of v from above, we get:

R = (2gh/g)sinθcosθ = 2hcosθsinθ

Part b) of the question:

Let's assume that the second hole is cut at a depth x above the bottom of the tank. We need to find the value of x such that the stream emerging from it could have the same range as for the first hole.

This means that the horizontal distance R must be the same for both holes. Using the expression for R from above, we get:

2hcosθsinθ = (2gh/g)sinθcosθ

Simplifying, we get:

x = H - h/4

To know more about Bernoulli's equation:https://brainly.com/question/15396422

#SPJ11

The fireman's hose is pointed vertically upwards at a height of 1.5 m above the ground and a stream of water is coming from it. When the water is shut off, the noise of the water hitting the ground continues for another 2.0 s, the speed of the water as it left the hose is  4.31 m/s.

A firefighter, also known as a fireman or firewoman, is a professional who is trained and equipped to put out fires, rescue people and animals from dangerous situations, and manage other emergency situations.

The water comes to rest after it reaches the ground, so it moves at constant acceleration in the vertical direction. Since the final velocity is zero, the initial velocity and the displacement can be used to calculate the time of flight.

The speed at which the water left the hose can then be determined using the time of flight and the height of the hose above the ground.

Initial velocity = v₀, Final velocity = vf = 0.

Displacement = h = 1.5 m

Acceleration = a = g = 9.8 m/s²

Time of flight = t

Using the formula ,vf = v₀ + at₀ = v₀ + gt

v₀ = -gt

displacement = v₀×t + 1/2×at²

h = -1/2 × gt²

t = sqrt(2h/g) = sqrt(2(1.5)/9.8) = 0.44 s.

Using the formula, vf = v₀ + at

vf = 0 + gtvf = 9.8 × 0.44 = 4.31 m/s.

The water's speed as it leaves the hose is 4.31 m/s.

Read more about speed here:

https://brainly.com/question/27888149

#SPJ11

Answer:

The correct answer is "glass".

Explanation:

A room with a smooth and hard surface like the glass is likely to produce an echo because when sound waves hit such surfaces, they bounce back and forth, creating echoes. Soft and porous materials like carpet, dirt, or foam absorb sound waves, reducing the reflection and producing less echo. Therefore, the answer is glass.

According to the Third Kepler Law, the average distance from the Sun (A) is directly proportional to the cube root of the orbital period (T). So, for a new planet with an orbital period of 6548 years, we can calculate the average distance (A) using the equation: A = (T^(1/3)) x (A_earth^(2/3)), where A_earth is the average distance of the Earth from the Sun, which is approximately 150 million km.
Plugging in the given values, we get: A = (6548^(1/3)) x (150x10^6 km)^(2/3) = ∼260AU.

Therefore, the average distance from the Sun for the newly-discovered planet in our solar system is ∼260AU.
The average distance from the sun for the newly-discovered planet in our solar system is approximately 240AU.Kepler's third law states that the square of the orbital period is proportional to the cube of the semi-major axis of the orbit. It states that "the square of the period of revolution of a planet is proportional to the cube of the semi-major axis of its orbit." Kepler's third law mathematically connects the distance of a planet from the sun and its orbital period, that is, a planet's "year" or "revolution."The equation used to relate the third Kepler law is: T2 = (4π2 a3) / GMWhere T is the orbital period, a is the semi-major axis of the orbit, G is the gravitational constant, and M is the mass of the Sun. The value of T is provided as 6548 years, which is substituted in the equation above:6548^2 = (4π2 × a3) / (6.674 × 10-11 × 1.989 × 1030)Solving for a, we get:a = 239.8 ≈ 240 AU.Hence, the answer is option C. ~240AU.

For more such questions on Third Kepler Law

https://brainly.com/question/12251720

#SPJ11

The best describes the movement of the object between the times of 0 and 6 on the graph is moving at a constant speed. Therefore, option A is correct.

Moving occurs when an object's location compared to a fixed spot changes. Even seemingly stationary things shift. When one item moves in connection to another, we say it is moving relative to the other object.

Kinematics is the field of physics concerned with forces and their effects on motion, whereas dynamics is concerned with forces and their effects on motion. When a force pushes or draws on an item, it moves in the same way as the force.

Thus, option A is accurate because the object moves at a consistent pace between periods 0 and 6 on the graph.

To learn more about the movement of an object, follow the link;

brainly.com/question/2288841

#SPJ1

a) The wheel's angular velocity after 7.0 s is 43.29 rpm.

b) The wheel makes 4.66/2π or 0.74 revolutions in this time.

a)The angular velocity, constant angular acceleration:

ω = ω0 + αt

Where, ω is the final angular velocity

ω0 is the initial angular velocity

α is the constant angular acceleration

t is the time elapsed

Substituting the given values,

ω = ω0 + αt

  = 40 rpm + 0.47 rad/s² × 7 s

  = 40 rpm + 3.29 rpm

  = 43.29 rpm

B)The number of revolutions, the total angle rotated by the wheel is in radians.

θ = ω0t + 1/2αt²

Where θ is the total angle rotated in radians t is the time elapsed

Substituting the given values,

θ = ω0t + 1/2αt²

 = (2π × 40 rpm/60) × 7.0 s + 0.5 × 0.47 rad/s² × (7.0 s)²

 = 4.66 rad

To know more about angular velocity:

brainly.com/question/30237820

#SPJ11

4.92 m/s for her final velocity.

The momentum of the skater before throwing the stone is:

p1 = m1 * v1 = 50 kg * 5 m/s = 250 kg*m/s

where m1 is the mass of the skater and v1 is her initial velocity.

When the skater throws the stone, the total momentum of the system (skater + stone) is conserved. The momentum of the stone is:

p2 = m2 * v2 = 2 kg * 2 m/s = 4 kg*m/s

where m2 is the mass of the stone and v2 is its velocity.

Let's assume the skater throws the stone in front of her. To conserve momentum, the skater will move in the opposite direction to the stone. Let's call the skater's final velocity v3. Then:

p1 = p2 + p3

where p3 is the momentum of the skater after throwing the stone. Substituting the values we get:

250 kgm/s = 4 kgm/s + 50 kg * v3

Solving for v3, we get:

v3 = (250 kgm/s - 4 kgm/s) / 50 kg = 4.92 m/s

So the skater's speed after throwing the stone in front of her is 4.92 m/s.

If the skater throws the stone behind her, the same conservation of momentum principle applies, and we get the same result of 4.92 m/s for her final velocity.

Sorry if I'm wrong

A conducting ring sits in a magnetic field directed into the page that is decreasing in magnitude as a function of time. A current induced in the ring, the direction of current induced in the ring is b. counterclockwise.

Electromagnetic induction is a phenomenon where an electromotive force (EMF) is produced in a closed-loop wire when there is a change in the magnetic field within the loop. Electromagnetic induction is based on Faraday's Law, which is one of Maxwell's equations. It's named after Michael Faraday, who discovered it. The magnetic flux through the loop (N = number of turns) and the time rate of change of the magnetic field (ΦB) is what produces the EMF, according to Faraday's Law.

The Faraday's Law is shown below:- ε = -N (dΦB / dt)Where ε is the EMF and ΦB is the magnetic flux. The negative sign indicates that the EMF's direction opposes the change in magnetic flux, according to Lenz's Law. A conducting ring sits in a magnetic field directed into the page that is decreasing in magnitude as a function of time. Is a current induced in the ring? Yes, a current is induced in the ring.What is the direction of current induced in the ring?The induced current in the ring is counterclockwise.

Learn more about Faraday's Law at:

https://brainly.com/question/1640558

#SPJ11

Answer:

b

Explanation: friction is like a force to something to react

(d) n=3 to 1 would emit the shortest wavelength. Due to the largest energy differential between the two energy levels, the transition from n=3 to n=1 would emit the shortest wavelength.

Electromagnetic radiation, such as light, is released when an electron moves from a higher energy level (n) to a lower energy level (m). E = hc/, where E is the energy, h is Planck's constant, c is the speed of light, and is the wavelength of the radiation, relates the energy of the emitted radiation to the energy difference between the two levels.

Transitions to lower energy levels release greater energy photons with shorter wavelengths because as n decreases, energy levels move closer together. Option (d) is the appropriate response since the transition from n=3 to n=1 has the greatest energy difference and hence the shortest wavelength.

learn more about wavelength here:

https://brainly.com/question/31143857

#SPJ4

(a) Free-body diagram of block is as given below. (b) Acceleration of the block is 2.529 m/s². (c) Speed of the block when it reaches the bottom of the incline is 3.18 m/s.

Frictionless surface is an invented concept of surface that is based on imagination and creative ideas of scientists where assumed friction of surface is zero.

(a) Free-body diagram of block is:

            /|

           / |

          /  | m

         / θ |

        /    |

       /_____|

        f ||

          ||

          ||

          ||

          \/

where m is mass of the block, θ is angle of inclination, f is force of friction (which is zero in this case), and g is acceleration due to gravity acting vertically downwards.

(b) The force acting along incline is component of the weight of block parallel to the incline, given by mg sin θ, where m is the mass of the block and g is acceleration due to gravity. Since there is no friction, this force is equal to net force acting on block, which is ma, where a is acceleration of block along the incline. Therefore,

mg sin θ = ma

a = g sin θ

a = 9.81 m/s² * sin 15.00 = 2.529 m/s²

Therefore, the acceleration of the block is 2.529 m/s².

(c) v² = u² + 2as

where u is the initial velocity (which is zero), s is the displacement (which is 2.00 m along the incline), and a is the acceleration (2.529 m/s²). Solving for v, we get:

v = √(2as) = √(2 * 2.00 m * 2.529 m/s²) = 3.18 m/s

Hence, speed of block when it reaches bottom of incline is 3.18 m/s.

To know more about frictionless surface, refer

https://brainly.com/question/25825478

#SPJ1

If work is done on an object, the object has more energy than it did before. This energy can come from increases in kinetic energy, potential energy, and/or internal energy.

The energy transferred into an object by an external force is the work done on that object. The unit of work is the joule (J). Work can be expressed as a dot product of the force and the displacement, as given below:

W = F . d

Energy is the capacity of a system to do work. There are many different forms of energy, which can be classified as kinetic, potential, or internal energy.

Kinetic energy is the energy of motion. The kinetic energy of an object of mass m and velocity v is given by the equation below:

K = (1/2)mv²

Potential energy is the energy that a system possesses because of its position in a gravitational or electric field. A body's potential energy depends on its mass, height, and position. An object has gravitational potential energy when it is in a position that can potentially fall to a lower height. A system's electric potential energy is a result of the potential difference between two points.

Internal energy is the energy that a system possesses due to the motion of its atoms and molecules. The total energy of a system is the sum of its kinetic and potential energy. The internal energy of a system is the sum of the energy associated with the motion and position of its atoms and molecules. When energy is transferred to a system by an external force, some of that energy is converted to internal energy.

Learn more about Energy here: https://brainly.com/question/874116

#SPJ11