A scale of 1:900,000 is _____________ a scale of 1:24,000:
A - equal to
B - smaller than
C - twice as much as
D - larger than

The initial speed of the car was approximately 24.9 m/s.

We can use the equation for the work done by kinetic friction to find the initial speed of the car. The work done by kinetic friction is given by:

W_friction = F_friction * d

where;

The force of kinetic friction is given by:

F_friction = m * g * μ

where;

The work done by kinetic friction is equal to the change in kinetic energy of the car:

W_friction = (1/2) * m * v^2

where;

Setting these two equations equal to each other and solving for v, we get:

(1/2) * m * v^2 = F_friction * d

(1/2) * m * v^2 = m * g * μ * d

v^2 = 2 * g * μ * d

v = √(2 * g * μ * d)

Substituting the given values, we get:

v = √(2 * 9.81 m/s^2 * 0.85 * 45 m)

v = 24.9 m/s

Learn more about initial speed here: https://brainly.com/question/24493758

#SPJ1

To verify whether you accurately pipette 950l of water into each tube, measure the actual weight of water and compare it with calculated weight.

To verify if you accurately pipetted 950 mL of water into each tube, you can weigh each tube before and after adding the water. Since you know the density of water, you can calculate the expected weight of the water in each tube, which should be equal to 950 g or 0.95 kg.

By subtracting the weight of an empty tube from the weight of a tube filled with water, you can determine the actual weight of the water added to the tube. If the actual weight is close to 0.95 kg, then the pipetting was accurate.

To know more about the pipette, here

brainly.com/question/28839494

#SPJ4

The two balls will meet at a time of 1.42 seconds.

The speed of the balls when they meet are  -6.476 m/s and 13.956 m/s respectively.

To determine when and where the two balls meet, we can use the vertical motion equations.

The first ball is thrown upwards, so its motion is governed by the equation of motion:

h(t) = h0 + v0t - 1/2gt^2

where;

The second ball is dropped from rest, so its initial velocity is zero and it follows the equation:

h(t) = h0 - 1/2gt^2

To find the time and place where the two balls meet, we need to find the time t at which their heights are equal. Setting the two equations equal to each other and solving for t, we find:

t = √((2v0) / g)

t = √((2 * 9) / 9.8) = 1.42 s

At this time, both balls have fallen the same distance, so they are at the same height. To find their speeds when they meet, we use their respective equations of motion and the time t found above.

The speed of the first ball at t = 1.42 s is:

v(t) = v0 - gt

= 9 m/s - 9.8 m/s * 1.42 s

= -6.476 m/s

The speed of the second ball at t = 1.42 s is:

v(t) = gt

= 9.8 m/s * 1.42 s

= 13.956 m/s

Learn more about speed here: https://brainly.com/question/6504879

#SPJ1

Conventionally, the field strength around a charged object is the direction of the force acting on a "positive test charge".

This convention is used because positive charges and negative charges experience opposite forces in an electric field, so the direction of the field is defined based on the force experienced by a positive charge. By convention, a positive test charge is used to define the direction of the field, even though in reality the direction and magnitude of the field would be the same for a negative test charge. This convention helps to avoid confusion and ensure consistent understanding of the direction and properties of electric fields.

You can learn more about field strength around a charged object at

https://brainly.com/question/3867990

#SPJ4

Communication cannot be undone once it has been sent, hence it is impossible to undo any effects it may have had on the recipient.

Interpersonal communication is an irreversible process; you can later apologize for something you said and wish you hadn't said it, but you can't take it back. We frequently act and speak with people depending on prior communication experiences.

In passive sentences, the typical word order is reversible. The two stamps were turned on their sides by him. A second vehicle backed out of the drive. He drove away after doing a U-turn. Driving backwards directly at the officer of the law, he.

To know more about communication visit:-

https://brainly.com/question/13008699

#SPJ1

If 3 circular bars made up of glass, steel, aluminium having equal cross section applied with muiltiaxial load at same point in same direction , The bar will produce more stress: glass

If 3 circular bars made up of glass, steel, aluminium having equal cross section applied with muiltiaxial load at same point in same direction, the bar made of glass will produce more stress.

This is because the modulus of elasticity of glass is lower than that of steel and aluminium. The modulus of elasticity is a measure of a material's resistance to deformation under load. A lower modulus of elasticity means that the material is more prone to deformation and therefore, will produce more stress under the same load.

In general, the stress produced in a material under load is given by the equation:

stress = load / cross-sectional area

Since the cross-sectional area of the bars is equal and the load applied is the same, the stress produced will depend on the modulus of elasticity of the material. Therefore, the bar made of glass will produce more stress under the same load as compared to the bars made of steel and aluminium.

To know more about stress refer here:

https://brainly.com/question/30646193#

#SPJ11

The steel bar will produce the most stress when applied with a multi-axial load at the same point in the same direction, as steel is the strongest of the three materials (glass, steel, and aluminium).

The bar made of steel will produce more stress under a multi-axial load at the same point in the same direction. This is because steel has a higher Young's modulus, or the measure of the ability of a material to withstand changes in length when under tension or compression, than glass or aluminum. Therefore, it will experience greater stress under the same loading conditions. Steel has a much higher Young's modulus than glass or aluminum, meaning it will experience greater stress under the same loading conditions.

For more such questions on Young's modulus.

https://brainly.com/question/30756002#

#SPJ11

The child must use a wrench that is at least 20 centimeters long to remove the nut with the maximum force they can exert.

The torque exerted by the child must be equal to or greater than the required torque of 10 N·m to remove the nut. The formula for torque is torque = force x length x sin(theta), where theta is the angle between the force and the wrench.

Rearranging the formula, we can find the required length of the wrench by dividing the required torque by the force and the sin of the angle.

Length = Torque / (Force x sin(theta))

Using the given values, we get:

Length = 10 N·m / (50 N x sin(90°))

sin(90°) = 1

Length = 0.2 meters or 20 centimeters

Therefore, the child must use a wrench that is at least 20 centimeters long to remove the nut with the maximum force it can exert.

For more questions like Torque click the link below:

https://brainly.com/question/7580653

#SPJ4

The peak wavelength of light coming from a star with a temperature of 5300 K is 550 nm.

The peak wavelength of light coming from a star with a temperature of 5300 K can be calculated using Wien's law. According to Wien's law, the peak wavelength of a blackbody is inversely proportional to its temperature. The peak wavelength of a blackbody with a temperature of 5300 K can be calculated using the equation: λpeak = 0.0029/T, where T is the temperature in K. Plugging in the temperature of 5300 K into the equation results in a peak wavelength of 0.00055 μm or 550 nm. Therefore, the peak wavelength of light coming from a star with a temperature of 5300 K is 550 nm.

To learn more about wavelength

brainly.com/question/13533093

#SPJ4

The peak wavelength coming out of a star which has a temperature of 5300 K is 547 if 1 nm=  10-9 m

Peak wavelength is the one wavelength at which the light source's radiometric emission spectrum is at its broadest. Simply put, it represents photo-detectors rather than the human eye's perception of any emission from the light source.

To calculate a peak wavelength, we have to divide Wien's displacement constant by the absolute temperature

The Wien's displacement law, which states that the absolute temperature of a black body is inversely proportional to the electromagnetic wavelength at its maximal radiation intensity, is the law for which Wien's constant is well known.

Learn more about Peak wavelength here brainly.com/question/11274711

#SPJ4

A wavelength of 5 pm corresponds to the X-ray region of the electromagnetic spectrum.

The range of electromagnetic radiation's frequencies, along with the corresponding photon energies and wavelengths, is known as the electromagnetic spectrum.

All radio waves (such as commercial radio and television, microwaves, and radar), infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays are all included in the entire electromagnetic spectrum, which ranges in frequency from the lowest to the highest (longest to shortest wavelength).

Learn more about the electromagnetic spectrum at: https://brainly.com/question/2261239

#SPJ1

The earth's rotation generates the coriolis force, which makes objects hurled farther have more buoyant force.

The velocity Centripetal force is an outward force brought on by the rotation of the earth. In the northern hemisphere, the Coriolis force causes winds to be deflected to the right, and in the southern hemisphere, to the left. It is often referred to as "Ferrel's Law." When the wind speed is high, the deflection is greater.

The Coriolis force is most noticeable in the longitudinal course of an object. On Earth, an object traveling in a north-south direction will appear to be deflected to the north of the Equator and to left with in Southern Hemisphere.

To know more about velocity visit :

https://brainly.com/question/18084516

#SPJ4

After the bullet escapes, the block moves at a speed of 59.4 m/s.

The conservation of momentum can be used to resolve this issue. Since there is no outside force operating on the bullet or the block prior to impact, the system's overall momentum is zero. Following the bullet's passage through the block, the bullet and block will move at different speeds, but the system's overall momentum will still be conserved.

Allow v to represent the block's velocity after the bullet leaves. The initial momentum of the system is 0 since the block is initially at rest.

(m block*v block) + (m bullet*v bullet)

where m bullet is the bullet's mass, v bullet is its exit-block velocity, and m block is the block's mass.

The initial energy of the system is:

(1/2) * m_bullet * v_bullet^2

The final energy of the system is:

(1/2) * m_bullet * v_bullet^2 + (1/2) * m_block * v^2

Since the energy is conserved, we can set the two expressions equal to each other and solve for v:

(1/2) * m_bullet * v_bullet^2 = (1/2) * m_bullet * v_bullet^2 + (1/2) * m_block * v^2

v^2 = (m_bullet / m_block) * (v_bullet^2 - v^2)

Plugging in the given values:

v_bullet = 240 m/s

m_bullet = 3.0 g = 0.003 kg

m_block = 2.1 kg

v^2 = (0.003 / 2.1) * (540^2 - 240^2)

v^2 = 3534

v = 59.4 m/s

Therefore, the speed of the block immediately after the bullet exits is 59.4 m/s.

Learn more about momentum here:

https://brainly.com/question/30677308

#SPJ4

Answer:

4000j

Explanation:

0.5 × 10^2 × 80 = 4kJ = 4000Joules

None of the options would cause the most worry about the validity of this interval. Option e is the correct answer.

Option c would cause the most worry about the validity of the 95% confidence interval. This is because the confidence interval is calculated using the sample standard deviation and the t-distribution, assuming that the population standard deviation is unknown.

If the population standard deviation is significantly different from the sample standard deviation, the confidence interval may not accurately reflect the population mean. Therefore, options a, b, d, and e are not a problem for the validity of the interval.

To know more about the standard deviation, here

brainly.com/question/23907081

#SPJ4

--The complete question is, Scientists collect data on the blood cholesterol levels (milligrams per deciliter of blood) of a random sample of 25 laboratory rats. A 95% confidence interval for the mean blood cholesterol level μ is 80.2 to 89.8. Which of the following would cause the most worry about the validity of this interval?

a. There is a clear outlier in the data

b. A stem-plot of the data shows a mild right skew

c. You do not know the population standard deviation σ

d. The population distribution is not exactly Normal.

e. None of these are a problem when using t-interval--

The magnitude of the electric field inside the capacitor is: E = 93.53 x 10^3 N/C (or 93.53 kN/C)

An electric field is a physical quantity that describes the influence that an electric charge exerts on other charges within the space around it. It is defined as the force per unit charge that a test charge would experience at a given point in space, in the presence of an electric charge or charges.

Electric fields are typically represented by vectors, which have both magnitude and direction. The strength of an electric field is measured in units of volts per meter (V/m).

Electric fields are fundamental to understanding the behavior of electrical systems, including electronic circuits and power grids. They also play a critical role in the functioning of many natural phenomena, such as lightning, the aurora borealis, and the behavior of atoms and molecules.

Part (a) To find the charge on one of the plates, we can use the formula:

Q = C x V

where Q is the charge, C is the capacitance, and V is the potential difference.

Substituting the given values, we get:

Q = 0.072 F x 333 V = 23.976 C ≈ 2.4 x 10^-11 C

Therefore, the charge on one of the plates is approximately 2.4 x 10^-11 coulombs.

Part (b) To find the distance between the plates, we can use the formula:

C = ε0 x (A/d)

where ε0 is the permittivity of free space, A is the area of each plate, and d is the distance between the plates.

Solving for d, we get:

d = ε0 x A / C

Substituting the given values, we get:

d = (8.85 x 10^-12 F/m) x (0.29 m)^2 / 0.072 F = 3.56 x 10^-6 m = 3.56 micrometers (μm)

Therefore, the distance between the plates is approximately 3.56 μm.

Part (c) The electric field inside the capacitor can be calculated using the formula:

E = V/d

where V is the potential difference and d is the distance between the plates.

Substituting the given values, we get:

E = 333 V / (3.56 x 10^-6 m) = 93.53 x 10^3 V/m

However, the question asks for the magnitude of the electric field in newtons per coulomb. To convert from volts per meter to newtons per coulomb, we can use the formula:

1 V/m = 1 N/C

Therefore, the magnitude of the electric field inside the capacitor is:

E = 93.53 x 10^3 N/C (or 93.53 kN/C)

To know more about coulomb visit:

https://brainly.com/question/15167088

#SPJ1

If the equilibrant vector is calculated and placed correctly on the force table, we expect the ring to "remain stationary or in a state of equilibrium".

In a force table experiment, the goal is to determine the vector sum of two or more forces acting on an object. The equilibrant is the vector that has the same magnitude as the vector sum of the given forces but is opposite in direction. When the equilibrant is added to the forces, the resulting vector sum will be zero, indicating that the forces are in balance and the object is in equilibrium.

If the equilibrant vector is calculated correctly and placed on the force table, it will cancel out the given forces, and the net force acting on the ring will be zero. Therefore, the ring will not experience any acceleration and will remain stationary.

In summary, if the equilibrant vector is calculated and placed correctly on the force table, we expect the ring to be in a state of equilibrium and remain stationary.

You can learn more about equilibrant vector at

https://brainly.com/question/24042341

#SPJ4

Initial acceleration is the acceleration of an object at a specific moment in time, typically at the start of a motion. It is the acceleration of an object at the beginning of its motion or when it is first subjected to a force.

Acceleration is a vector quantity that describes the rate at which an object's velocity changes with respect to time. It is the measure of how quickly the object's speed and/or direction is changing. An object can have varying accelerations depending on the forces acting on it, such as gravity or friction.The initial acceleration can be calculated using the formula a = v^2/r, where v is the initial velocity and r is the radius of circular path.

To solve this problem, use the conservation of energy and Newton's second law.

First, calculate the height of point B above point A.

Use the fact that the vertical component of the motorcycle's velocity is zero at the top of the circle, so the kinetic energy is entirely due to the horizontal component of velocity. Therefore, at point B, the kinetic energy of the motorcycle is equal to the potential energy it had at point A:

[tex]mgh = 1/2 mv^2[/tex]

where m is the mass of the motorcycle, g is the acceleration due to gravity, h is the height of point B above point A, and v is the speed of the motorcycle at point B.

Cancel out the mass of the motorcycle, and use the given values to solve for h:

[tex]gh = 1/2 v^2 - 1/2 vA^2[/tex]

[tex]h = (1/2 v^2 - 1/2 vA^2) / g[/tex]

[tex]h = (1/2 (v^2 - vA^2)) / g[/tex]

[tex]h = (1/2 ((0.04 s) t)^2 - 2^2) / 32.2 ft/s^2[/tex]

[tex]h = (0.0008 t^2 - 4) / 32.2 ft[/tex]

Next, use the fact that the motorcycle's acceleration is directed towards the centre of the circle, and has a magnitude of:

[tex]a = v^2 / r[/tex]

where r is the radius of the circle. At point A, the velocity is purely horizontal, so the initial acceleration is:

[tex]aA = vA^2 / r[/tex]

Use the fact that the acceleration is given by:

[tex]a = d(˙v)/dt[/tex]

where ˙v is the rate of change of the velocity with respect to time. Integrating this equation gives:

v - vA = ∫a dt

v = vA + ∫a dt

Since the acceleration is constant, substitute the expression  derived for aA and integrate over the time it takes the motorcycle to travel from A to B. We can use the fact that the distance traveled along the circle is equal to the height difference h we calculated earlier, so the time it takes to travel from A to B is:

[tex]t = sqrt(2h / g)[/tex]

[tex]t = sqrt((0.0008 t^2 - 4) / 16.1)[/tex]

Squaring both sides and rearranging, we get a quadratic equation in t^2:

[tex]t^4 - 27.3t^2 + 674.5 = 0[/tex]

Solving for t^2 using the quadratic formula, we get:

[tex]t^2 = 13.4 or t^2 = 50.3[/tex]

Since the time cannot be negative, take the positive root:

t = 3.66 s

Substituting this value into the expression for the velocity,

[tex]v = 2 ft/s + (0.04 s/ft/s^2)(3.66 s)[/tex]

[tex]v = 2.1464 ft/s[/tex]

Therefore, the magnitude of the motorcycle's velocity when it reaches point B is approximately 2.15 ft/s. The initial acceleration is:

[tex]aA = vA^2 / r = (2 ft/s)^2 / 16 ft = 0.25 ft/s^2[/tex]

To know more about Initial Acceleration, visit:

https://brainly.com/question/460763

#SPJ4

A motorcyclist is traveling along a vertical circular path. At point A, the motorcyclist has an initial velocity of vA = 2 ft/s and an initial position of s = 0. The motorcyclist increases their speed along the path at a rate of ˙v = (0.04s) ft/s^2, where s is in feet. Determine the magnitude of the motorcyclist's velocity when they reach point B. Also, what is the motorcyclist's initial acceleration at point A?

Following are the answer:

Potential energy is the energy possessed by an object due to its position or configuration relative to other objects. It is the energy that an object has stored in it as a result of its position or state. An object's potential energy is often associated with its ability to do work, which can be released when the object is allowed to move or change its position.

(a) The potential energy stored in a spring stretched by a distance x from its equilibrium position can be calculated using the formula:

[tex]U = (1/2) k x^2[/tex]

where k is the spring constant.

Substituting the given values, we get:

[tex]U = (1/2) (440.0 N/m) (0.0415 m)^2U = 0.0424 J[/tex]

Therefore, the potential energy stored in the spring when it is stretched 4.15 cm from equilibrium is 0.0424 J.

(b) Using the same formula as in part (a), but with x = 0.0296 m, we get:

[tex]U = (1/2) (440.0 N/m) (0.0296 m)^2U = 0.0207 J[/tex]

Therefore, the potential energy stored in the spring when it is stretched 2.96 cm from equilibrium is 0.0207 J.

(c) When the spring is unstretched, its potential energy is zero, since there is no displacement from equilibrium. So the potential energy stored in the spring is zero.

Learn more about potential energy here:

https://brainly.com/question/24284560

#SPJ9

If we replace the incandescent bulb with a voltage meter and return the loop to its original configuration, then moving the bar magnet back and forth through the loop will induce an electrical current in the loop, as described by Faraday's law of electromagnetic induction.

A magnet is a material or object that produces a magnetic field, which is a force that can attract or repel certain other materials, such as iron or steel. The magnetic field is created by the motion of electric charges within the magnet, which align in such a way that they produce a net magnetic field. Magnets can be made from a variety of materials, including iron, cobalt, nickel, and certain alloys. They come in many different shapes and sizes, including bars, discs, horseshoes, and rings.

Here,

The type of current that is generated depends on the direction and rate of the magnet's motion. If the magnet is moved back and forth with a constant speed and in a straight line, the current induced in the loop will be an alternating current (AC), because the direction of the current will reverse every time the magnet changes direction. This can be observed by the voltage meter reading a voltage that periodically changes in direction.

To know more about magnet,

https://brainly.com/question/30563158

#SPJ1

One revolution is equal to 360 degrees, so the disk has completed 1/4 of a revolution or 0.25 revolutions.

We can use the fact that the angle rotated during the entire 1.0 s period is 90 degrees to calculate the number of revolutions completed. Disk accelerates at a rate of:

[tex]600 rad/s^2 for 1/2 s[/tex]

ω = ω0 + αt,(ω is the final angular velocity, ω0 is initial angular velocity, α is angular acceleration, t is the time). The angular velocity remains constant at 300 rad/s. Using the equation

θ = ω0t + 1/2 αt^2,

Now, v = rω, ( v is linear speed of dot, r is radius of  disk (which is half its diameter, or 4.0 cm), and ω is the angular velocity.

[tex]t = 1.0 s = 120 cm/s.[/tex]

To know more about angular velocity, here

https://brainly.com/question/30733452

#SPJ4

When a dielectric material is inserted between the plates of a parallel-plate capacitor while it remains connected to a battery, the following quantities change:

(a) C: becomes bigger

C = A/d, where is the permittivity of the medium between the plates, A is the area of the plates, and d is the distance between the plates, gives the capacitance of the capacitor. A dielectric material placed between the plates raises the medium's permittivity, which in turn raises the capacitor's capacitance. As a result, the capacitance rises.

A: remains the same (b)

Because the battery maintains a constant potential difference between the plates and the charge on the plates is equal and opposite, the charge on the capacitor stays constant. The charges on the plates are redistributed when the dielectric material is added, but the overall charge on the plates does not change.

(c) E between the plates: decreases

The electric field between the plates is given by E = V/d, where V is the potential difference between the plates. When a dielectric material is inserted between the plates, it reduces the electric field between the plates, as the voltage across the plates remains constant while the distance between them increases. Therefore, the electric field between the plates decreases.

(d) ΔV: decreases

The potential difference between the plates decreases when a dielectric material is inserted between them. This can be explained by the relationship V = Q/C, where V is the potential difference, Q is the charge on the plates, and C is the capacitance. Since the capacitance increases when the dielectric is inserted, the potential difference decreases for the same charge on the plates. Therefore, ΔV decreases.

(e) Energy stored in the capacitor: increases

The energy stored in a capacitor is given by U = (1/2)CV², where C is the capacitance and V is the potential difference between the plates. When a dielectric material is inserted between the plates, the capacitance increases and the potential difference decreases. Since the energy stored is proportional to the square of the potential difference, the decrease in ΔV is more than compensated by the increase in capacitance, leading to an overall increase in the energy stored in the capacitor. Therefore, the energy stored in the capacitor increases.

To know more about dielectric material , check out :

https://brainly.com/question/17090590

#SPJ4

The expression for the magnitude of the net force on the car as it is stopping in terms of the symbols given in the problem statement is:

Fnet = (ms/2)d + ma.

The expression for the magnitude of the net force on the car as it is stopping can be found by considering the forces acting on the car. Let's assume that the car is moving to the right and is being stopped by a force acting to the left. According to Newton's second law of motion, the net force on an object is equal to the product of its mass and its acceleration. In this case, the car is slowing down, so its acceleration is negative (i.e., pointing to the left).

Let Fnet be the magnitude of the net force on the car, m be the mass of the car, and a be the acceleration of the car. The force IEF1 can be considered as an external force acting on the car. Therefore, we can write:

Fnet = IEF1 - ma

Substituting the given expression for IEF1 and the assumption that the acceleration is negative, we get:

Fnet = (ms/2)d - (-ma)

Simplifying the expression, we get:

Fnet = (ms/2)d + ma

Therefore, the expression for the magnitude of the net force on the car as it is stopping in terms of the symbols given in the problem statement is:

Fnet = (ms/2)d + ma

Here you can learn more about the magnitude

https://brainly.com/question/18506683

#SPJ4

The speed of the Olympic-class sprinter 3.23 seconds later is 12.54 m/s.

The speed of the Olympic-class sprinter 3.23 seconds later can be found using the equation for speed, which is:

speed = acceleration × time.

In this case, the acceleration is 3.88 m/s² and the time is 3.23 seconds.

Speed refers to the rate at which an object covers a certain distance over time. It is typically measured in units of distance per unit of time, such as meters per second (m/s) or kilometers per hour (km/h).

The formula for speed is:

So, the equation would be:

speed = 3.88 m/s² × 3.23 s

By multiplying these two values, we can find the speed of the sprinter 3.23 seconds later:

speed = 12.54 m/s

To learn more about Speed :

https://brainly.com/question/13943409

#SPJ11

The maximum speed at that a car can travel around the curve without slipping is 13.7 m/s.

In this situation, the coefficient of static friction (μs) is 0.34 and the coefficient of kinetic friction (μk) is 0.29. The radius of the curve (r) is 56.0m.

We can use these values to calculate the maximum speed that a car can travel around the curve without slipping. This is determined by the centripetal force (Fc) required to keep the car on the curve and the frictional force (Ff) that keeps the car from sliding off the curve.

The equation for centripetal force is

Fc = mv^2/r,

where m is the mass of the car and v is the speed of the car.

The equation for frictional force is

Ff = μsFn,

where Fn is the normal force.

Since the car is on a level surface,

Fn = mg,

where g is the acceleration due to gravity.

Setting Fc equal to Ff and solving for v gives us the maximum speed that the car can travel around the curve without slipping:

mv^2/r = μsmg v^2

=> μsrg v

=> √(μsrg) v

=> √(0.34 * 56.0m * 9.8m/s^2) v

=> 13.7 m/s

To learn more about  Maximum speed :

https://brainly.com/question/30193604

#SPJ11

The velocity of the particle at the moment it reaches its maximum x coordinate is (1.9 î + 7.4 į)m/s and the position of the particle at the moment it reaches its maximum x coordinate is approximately 2.6 î + 2.8 į m from the origin.

(a) To find the velocity of the particle at the moment it reaches its maximum x coordinate, we need to find the time at which the particle reaches this point. We can use the kinematic equation:

x = x0 + v0t + 0.5at^2

where x0 = 0, v0 = 5.0 m/s along the positive x axis, a = (-2.5 î + 4.9 įm/s2), and x is the maximum x coordinate. We can solve for t by setting the velocity to zero:

v = v0 + at = 0

t = -v0/a = -5.0/(-2.5 î + 4.9 į) ≈ 0.75 s

Now, we can use the kinematic equation for velocity:

v = v0 + at

v = 5.0 + (-2.5 î + 4.9 į)m/s2 × 0.75 s = (1.9 î + 7.4 į)m/s

Therefore, the velocity of the particle at the moment it reaches its maximum x coordinate is (1.9 î + 7.4 į)m/s.

(b) To find the position of the particle at this moment, we can use the same kinematic equation for the position:

x = x0 + v0t + 0.5at^2

x = 0 + 5.0 m/s along the positive x axis × 0.75 s + 0.5(-2.5 î + 4.9 įm/s2) × (0.75 s)^2

x ≈ 2.6 î + 2.8 į m

Therefore, the position of the particle at the moment it reaches its maximum x coordinate is approximately 2.6 î + 2.8 į m from the origin.

For more questions like Velocity click the link below:

https://brainly.com/question/12975674

#SPJ4

To the west of the dotted line, the closed surface have various geometrical configurations. A charged particle is encircled by three distinct closed surfaces in (Figure 1): (a), (b), and (c). In every

What does the word "charge" mean?

to permeate or fill, such as a quality or feeling: Tension was charged in the air. 6. a. To accuse or blame someone for wrongdoing: The prosecutors accused him of car theft. The author was accused by critics of lacking creativity. b. To assign blame for; ascribe or impute: charged the driver's inexperience with being at fault for the accident.

What exactly is a charged expense?

Government expenses that must be covered without a vote are referred to as charged expenditures. It implies that these payments will take place regardless of whether Parliament approves the budget. Charged expenses are additionally referred to as "non-votable" expenses. The main account of the government is used to make these payments.

To know more about charged visit:

https://brainly.com/question/11568733

#SPJ4

If the axis is relocated on one of the sides, the inertial moment of a circular area about an axis going through its center of gravity is "(2)/(5)MR(2)".

I = ICM + MX2, where M is the body's mass and X is the separation between the axes, and I is the inertial moment about an axis passing through O. ICM is the inertia moment of the solid sphere of radius R about with an axis parallel towards the center of gravity.

a body's moment of inertia about an axis that is parallel to and passes through its which is created by multiplying the body's mass by the inverse of the separation between the two axis.

To know more about gravity visit :

https://brainly.com/question/14874038

#SPJ4

A acceptable acceleration for a jet plane in these circumstances is 25 m/s2. The jet in this problem accelerates quickly from cruising speed to a higher speed.

Velocity is the term for the rate at which a displacement changes. Acceleration is the term for the measurement of a change in velocity.

a. To determine the jet's acceleration, we can apply the equation for constant acceleration:

v_f² = v_i + 2ad

Substituting the given values, we get:

(400 m/s)² = (320 m/s)² + 2a(4.0 km)

Simplifying and solving for a, we get:

a = [(400 m/s)² - (320 m/s)²] / (2 × 4.0 km)

≈ 25 m/s²

To know more about acceleration visit:-

https://brainly.com/question/12550364

#SPJ4

Answer: the mass is18 kg

Explanation:

Answer:

Explanation:

Kinetic energy=1/2 *m *v^2

                      =1/2 * 18* 4.7*4.7=198.81J

Option B is the correct alternative, and the normal reaction on the automobile is mg cosθ if friction is negligible.

The correct alternative is option B: the normal reaction on the automobile is mg cosθ.

When an automobile enters a turn, it experiences a centripetal force that is directed towards the center of the turn. This force is provided by the component of the normal force that is perpendicular to the surface of the road. If the road is banked at an angle θ, the normal force has two components: one perpendicular to the road and one parallel to the road.

To maintain circular motion, the net force on the automobile must be directed towards the center of the turn. In the absence of friction, the only forces acting on the automobile are its weight and the normal force. Since the weight is always directed downwards, the normal force must provide the necessary centripetal force.

Normal force:

N = mg cosθ

where m is the mass of the automobile, g is the acceleration due to gravity, and θ is the angle of inclination of the road. This expression shows that the normal force is proportional to the weight of the automobile, and is reduced by a factor of cosθ due to the inclination of the road.

Learn more about friction here:

https://brainly.com/question/28941436

#SPJ4

(a) Value of true anomaly (v= 90°)(b) v= √2µ/explanation:the periapsis and apoapsis were defined as the points where the spacecraft is closest to and furthest from the planet, respectively.

The periapsis occurs when ν = 0 while the apoapsis occurs when ν = π. Suppose that the periapsis and apoapsis radii are denoted as rp and ra, respectively.

Simplifying Eqs. The periapsis and apoapsis radii are given as-rp = a(1 − e) equation  and ra = a(1 + e) equation (1.56)Recall from Eqs.

That the periapsis and apoapsis radii of the orbit of a spacecraft are given as rp = a(1 − e) and ra = a(1 + e), respectively.

At some point on the orbit between periapsis and apoapsis the radius, r, must be equal to the semi-major axis, a.

Assuming a gravitational parameter µ for the planet, determine(a) The value of the true anomaly when r = a. At r=a.

Therefore, it is true anomaly v= 90°(b) The speed of the spacecraft at the point when r = a.velocity v= √μ* √ 2/r-1/a sense, r=av= √2μ/a.

Learn more about periapsis here:

https://brainly.com/question/19500089

#SPJ4