Answer:
The plate thickness required at the base of the tank is approximately 6.6 mm.
Explanation:
To estimate the plate thickness required at the base of the tank, we need to determine the maximum pressure that the tank will experience at the base. The pressure can be calculated using the formula:
P = ρgh
where P is pressure, ρ is the density of the liquid, g is the acceleration due to gravity, and h is the height of the liquid above the base of the tank.
Assuming a density of 1.5 g/cm³ for concentrated nitric acid, the pressure at the base of the tank can be calculated as:
P = 1.5 x 9.81 x 16 = 235.44 kPa
To determine the plate thickness required, we can use the formula for the hoop stress in a cylindrical vessel:
σ = PD/2t
where σ is the stress, P is the pressure, D is the diameter of the vessel, and t is the thickness of the vessel wall.
Rearranging the formula to solve for t, we get:
t = PD/2σ
Assuming a diameter of 6 m and a design stress of 90 N/mm², the plate thickness required at the base of the tank can be calculated as:
t = (235.44 x 6 x 1000) / (2 x 90 x π) ≈ 6.6 mm
Therefore, the plate thickness required at the base of the tank is approximately 6.6 mm.
Answer:
To determine the plate thickness required at the base of the tank, we can use the following formula:
t = (PD)/(2SE - 0.2P)
where:
t = plate thickness
P = design pressure
D = inside diameter of the tank
S = allowable design stress for aluminum
E = joint efficiency factor
Since the tank will contain concentrated nitric acid, which is a hazardous material, it is subject to specific design and safety regulations that require a detailed engineering analysis. Therefore, we will assume a design pressure of 2.5 psi for this calculation, which is a typical value for atmospheric storage tanks.
The joint efficiency factor for welded aluminum is typically 0.70 to 0.85, depending on the welding procedure and inspection method used. For this calculation, we will assume a joint efficiency factor of 0.80.
Plugging in the given values, we get:
t = (2.56)/(2900.80 - 0.22.5)
t = 0.0682 m
Therefore, the plate thickness required at the base of the tank is approximately 0.0682 m, or 68.2 mm
A bett is tensioned to 704N whilst stationary in a belt pulley system. Calculate the tension in Newtons for the taught side given that the wheel is184 mmdiameter and5 kWof power are being transmitted at334rev/min. 1.480 .92 margin of error⋯2%Question 2 The engineering wrapped a belt around a drum 2.00 times, then applies a195 Nweight to one of the ends. It is calculated by a technician the coefficient of friction is 0.36 . What is the maximum weight inkNan the other end of the pulley system before slippage occurs.
The tension in Newtons for the taught side is 104.38 N. The maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN
Given that a belt is tensioned to 704 N whilst stationary in a belt pulley system. the wheel is 184 mm in diameter and 5 kW of power is being transmitted at 334 rev/min.
The formula to calculate the tension in the taught side of a belt pulley system is as follows:
T1 = (P×60)/(2×π×N) + (μ×P×60)/(2×π×N)
Where T1 is the tension in the taught side of the belt pulley system.
P is the power transmitted in kW.
N is the speed of rotation in rpm.
μ is the coefficient of friction in the belt pulley system.
Substituting the given values in the above equation,
T1 = (5×60)/(2×3.14×334) + (0.92×5×60)/(2×3.14×334)
T1 = 95.9 + 8.48T1 = 104.38 N (approx)
Therefore, the tension in Newtons for the taught side is 104.38 N (approx)
2: A technician calculated the coefficient of friction as 0.36 when an engineer wrapped a belt around a drum 2.00 times and then applied a 195 N weight to one of the ends.
The maximum weight that the other end of the pulley system can bear before slippage occurs can be calculated as follows:
μ = (T2 - T1)/W
Where μ is the coefficient of friction in the belt pulley system.
T1 is the tension in the tight side of the pulley system.
T2 is the tension in the slack side of the pulley system.
W is the weight attached to the slack side of the pulley system.
Substituting the given values in the above equation,0.36 = (T2 - 195)/W
Assuming T2 is greater than T1, the total tension can be calculated as follows:
T2 = 2T1T2 = 2(W + 195)W can be calculated as follows:
0.36W = 2W + 3900.64W = 3900W = 6093.75 N (approx)
Therefore, the maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN (approx).
To know more about belt pulley system:https://brainly.com/question/29718602
#SPJ11
1. The tension in Newtons for the taught side is 493.17 N. 2. The maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.
1. Tension = 704 N
Diameter of wheel (D) = 184 mm = 0.184 m
Power (P) = 5 kW = 5000 W
Speed (N) = 334 rpm
We need to find the tension in Newtons for the taught side.
The formula for tension in the belt pulley system is:
T1 - T2 = (P x 60) / (2πN) Here, T1 is the tension in the tight side and T2 is the tension in the slack side.
Substitute the given values in the above formula, we get:
T1 - T2 = (5000 x 60) / (2π x 334)T1 - T2 = 282.33N......(1)
As the bett is tensioned to 704N whilst stationary, we have T1 + T2 = 704N......(2)
Adding equations (1) and (2), we get:2T1 = 986.33NT1 = 493.17 N
Therefore, the tension in Newtons for the taught side is 493.17N.
2. Number of turns (n) = 2
Applied weight (W) = 195 N
Coefficient of friction (µ) = 0.36
We need to find the maximum weight in kN at the other end of the pulley system before slippage occurs.
The formula for maximum weight is:
Maximum weight (Wmax) = µ x n x W......(1)
Substitute the given values in the above formula, we get:
Wmax = 0.36 x 2 x 195
Wmax = 140.4 N
As the required answer is in kN, divide the above answer by 1000.
Wmax = 0.1404 kN.
Therefore, the maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.
To learn more about "tension": brainly.com/question/11348644
#SPJ11
Suppose that the current value of PC is 0x00004000. Can we use a single jump instruction to go to PC= 0x20014924?(if yes, write the jump instruction and show the value of the immediate field in Hex. If not, use a combinations of instructions to do so and show the immediate values in Hex)
No, we cannot use a single jump instruction to go from PC = 0x00004000 to PC = 0x20014924, since the jump instruction can only jump to a location within a certain range of the current PC value.
To jump to 0x20014924, we would need to use a combination of instructions, such as a branch instruction and a jump instruction. Here is an example of how we could do this:
Add the immediate value 0x20010924 to the current PC value 0x00004000 using the addi (add immediate) instruction:
addi $t0, $zero, 0x20010924
add $t0, $t0, $zero
Branch to the new address using the jalr (jump and link register) instruction:
jalr $zero, $t0, 0
The immediate value for the addi instruction would be 0x20010924, and the immediate value for the jalr instruction would be 0, since we want to jump to the address stored in register $t0.
To know more about range click here:
brainly.com/question/28135761
#SPJ4
Define the EvenNumber class for representing an even number. The class contains:
A data field value of the int type that represents the integer value stored in the object.
A no-arg constructor that creates an EvenNumber object for the value 0.
A constructor that constructs an EvenNumber object with the specified value.
A function named getValue() to return an int value for this object.
A function named getNext() to return an EvenNumber object that represents the next even number after the current even number in this object.
A function named getPrevious() to return an EvenNumber object that represents the previous even number before the current even number in this object.
Draw the UML diagram for the class. Implement the class. Write a test program that creates an EvenNumber object for value 16 and invokes the getNext() and getPrevious() functions to obtain and displays these numbers.
A. (The EvenNumber class) Define the EvenNumber class for representing an even number. The class contains: A data field value of the int type that represents the integer value stored in the object. A no-arg constructor that creates an EvenNumber object for the value 0. A constructor that constructs an EvenNumber object with the specified value. A function named getValue() to return an int value for this object. A function named getNext() to return an EvenNumber object that represents the next even number after the current even number in this object. A function named getPrevious() to return an EvenNumber object that represents the previous even number before the current even number in this object. Draw the UML diagram for the class. Implement the class. Write a test program that creates an EvenNumber object for value 16 and invokes the getNext() and getPrevious() functions to obtain and displays these numbers. B. Revise the EvenNumber class in Programming Exercise 2A to implement the preincrement, predecrement, postincrement, and postdecrement operators for getNext() and getPrevious() functions. Write a test program that creates an EvenNumber object for value 16 and invokes the ++ and -- operators to obtain next and previous even numbers.
B.Revise the EvenNumber class in Programming Exercise 2A to implement the preincrement, predecrement, postincrement, and postdecrement operators for getNext() and getPrevious() functions. Write a test program that creates an EvenNumber object for value 16 and invokes the ++ and -- operators to obtain next and previous even numbers.
Answer:
#include <iostream>
using namespace std;
class EvenNumber
{
private:
int integrer;
public:
EvenNumber ()
{
integrer=0;
}
EvenNumber (int number)
{
integrer=number;
}
int getvalue ()
{
return integrer;
}
int getnext ()
{
return integrer+2;
}
int getprevious ()
{
return integrer-2;
}
};
int main () {
EvenNumber sixteen(16);
cout<<"The value is: "<<sixteen.getvalue()
<<" the next even number is: "<<sixteen.getnext()<<
" and the previous number is: "<<sixteen.getprevious();
return 0;
}
Explanation:
Although many organizations prefer to use a single technology stack, it is not always viable because of various application needs. However, it is important to understand all the pieces of technology involved with certain technology stacks. The two most common are Microsoft .NET and Java-based technologies. In the selection of either, there are specific operating systems, databases, programming languages, development tools and servers that are used with each technology stack.Research all the necessary technical standards for a technology stack and make recommendations of what must be included for an organization to use that technology stack for software development.
An organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.
To use a technology stack for software development, an organization needs to include the following technical standards:
Operating System - A technology stack requires a specific operating system, as it is dependent on the underlying system that is used. An organization should choose the operating system that is most suitable for its needs.
Databases - It is important to select a database that supports the specific technology stack. For example, for Java-based technologies, Oracle is a commonly used database.
Programming Languages - Programming languages are an important aspect of a technology stack, and the organization should choose the language that is best suited for its needs.
Development Tools - An organization must choose development tools that support the specific technology stack that is being used. These tools should be easy to use and provide support for debugging and testing.
Servers - A technology stack requires specific servers to run on. An organization must choose the server that is most suitable for its needs, such as Apache Tomcat for Java-based technologies.
In conclusion, to use a technology stack for software development, an organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.
To know more about technology stack:https://brainly.com/question/23504399
#SPJ11
what were the gargoyles on a gothic cathedral are there _____.
the need to back up important data before installing new hardware is an example of the following constraint(s):
The need to back up important data before installing new hardware is an example of the following constraint(s): time constraint and cost constraint.
Constraints, also known as limitations or restrictions, are a set of parameters that limit the possible solutions to a specific issue or problem. Constraints come in a variety of forms, and the importance of a given constraint is determined by the problem being addressed. The need to back up important data before installing new hardware is an example of the following constraints:
Time constraint- This implies that there is a limited amount of time available to complete a task, and as a result, we must work within that time frame to accomplish our objectives. In this scenario, a time restriction is present because the installation of new hardware must be completed in a certain amount of time, necessitating the need to back up data before starting the procedure.
Cost constraint- This refers to the financial limits that restrict the amount of money available for the solution's execution. If the cost of backing up the data is too high, it may prohibit the new hardware installation. As a result, it's crucial to consider the cost of implementing a solution when dealing with a problem.
For more such questions on hardware
https://brainly.com/question/28494136
#SPJ11
How to use Goal Seek to calculate the changing value in a cell?
Goal Seek is used in Excel to determine the value that a certain cell needs to be changed to in order to reach a specific goal, by altering the value of another cell that is related to the goal cell through a formula or calculation.
When you use Goal Seek, you select a cell that contains a formula and specify the value that you want that formula to return by changing the value in another cell. Excel then uses a trial-and-error approach to determine the value that needs to be entered into the input cell to achieve the desired result.
For example, you might use Goal Seek to determine how much you need to save each month in order to reach a specific savings goal by a certain date. You would set the savings goal as the cell to be changed, and the monthly savings amount as the input cell to be adjusted until the goal is met.
Learn more about Goal Seek https://brainly.com/question/30404127
#SPJ11
5.2-1 A compact disc (CD) records audio signals digitally by using PCM. Let the audio signal bandwidth be 15 kHz (a) If the Nyquist samples are uniformly quantized into L binary-coded, determine the number of binary digits required to encode a sample. 65,536 levels and then (b) If the audio signal has average power of O.1 W and peak voltage of I V, find the resulting ratio of signal to quantization noise (SNR) of the uniform quantizer output in part (a) (c) Determine the number of binary digits per second (bit/s) required to encode the audio signal. (d) For practical reasons discussed in the text, signals Nyquist rate. Practical CDs use 44,100 samples per second. If L 65,536, detemine the number of bits per second required to encode the signal and the minimum bandwidth required to transmit the encoded signal. sampled at a rate well above the are
The number of binary digits needed to encode a sample is 16 if the Nyquist samples are uniformly quantized into L binary-coded.
Which two forms of audio signals are there?There are two basic categories of audio signals: analogue and digital. At the recording and playback ends, all audio is analogue sound, therefore digital sound can be viewed as an analogue sound that has been routed through computational machinery.
What is PCM audio on two channels?In many home theatre systems, PCM is the digital audio format that is used. It is a two-channel format, which means it can support up to two audio channels and deliver stereo sound through two speakers.
To know more about binary visit:-
https://brainly.com/question/10442521
#SPJ1
What vehicles are often required to shuttle fans to and from satellite parking lots?CarsTrainsBusesAll of the Above
What
IS
a
3-phase system.
Answer:
Explanation: Three-phase power is a three-wire ac power circuit with each phase ac signal 120 electrical degrees apart
Compute the terminal velocity of a spherical raindrop of diameter 0.05 inches. Assume it falls through air at standard sea level conditions DISCUSSION: How does the terminal velocity vary with droplet diameter?
To compute the terminal velocity of a spherical raindrop of diameter 0.05 inches, we must use Stoke's law.
What is the definition of terminal velocity?
The terminal velocity of a freely falling object is the speed at which it stops accelerating due to the force of air resistance acting on it, such that its acceleration becomes zero. The terminal velocity is a velocity that is reached when the force of air resistance balances the force of gravity on an object.
The terminal velocity of a spherical raindrop is given by:
[tex]v=2gr^2(p_s-p_f)/9(\eta)[/tex]
where v is the terminal velocity of the raindrop, g is the acceleration due to gravity (9.81 m/s²), r is the radius of the raindrop, [tex]p_s[/tex] is the density of the sphere (1,000 kg/m³ for water), [tex]p_f[/tex] is the density of the fluid through which the raindrop is falling (1.29 kg/m³ for air at standard sea level conditions), and η is the dynamic viscosity of the fluid (18.6 × 10⁻⁶ kg/(m·s) for air at standard sea level conditions).
Diameter variation with terminal velocity: As the diameter of the raindrop increases, its terminal velocity also increases. Larger raindrops have a higher terminal velocity than smaller raindrops due to the increased force of gravity acting on them. However, when a raindrop becomes too large, it will split into smaller droplets due to surface tension.
Learn more about terminal velocity here:
https://brainly.com/question/30466634
#SPJ11
Which of the following answers refers to a system containing mappings of ?domain names to various types of data, such as numerical IP addresses * TCP/IP O DNS O DHCP O SQL O Ignore o
The Domain Name System (DNS) is a hierarchical decentralized naming system that maps human-readable domain names to numerical IP addresses used to locate and identify network resources on the internet. Option A is the correct answer.
DNS acts as a phonebook for the internet by translating domain names, such as www.example.com, into the corresponding IP addresses, such as 93.184.216.34. DNS provides a distributed database that allows for the efficient and reliable resolution of domain names to IP addresses by utilizing a network of servers to handle queries and responses. DNS also supports the mapping of other types of data, such as mail servers and service location records, and is a critical component of the internet infrastructure.
Option A) DNS is the correct answer.
You can learn more about Domain Name System (DNS) at
https://brainly.com/question/18274277
#SPJ11
What is the minimum number of electoral votes needed to win a presidential election?
Answer:
Explanation:
270
you are tasked with setting up a server for your company. explain how you would arrange the storage so that you meet the specifications set by your boss that no data can be lost, due to failed hard drive, etc.
The ways of arranging the storage so that you can meet the specifications set by your boss:
RAID – (Redundant Array of Independent Disks)BackupCloud storageThe first method for organizing a storage system is RAID. It is one of the most reliable methods for protecting data from hard drive failure. The RAID system uses several hard drives and combines them into a single volume. Data is then written across the drives, thus ensuring that if one fails, there is no data loss.A backup is an excellent method to safeguard data against potential loss due to hardware or software failure. Your storage system should have a routine backup schedule that backs up critical data regularly. The use of cloud storage is increasing in popularity. Cloud storage is a great way to safeguard data against loss due to hardware or software failure.
Learn more about RAID: https://brainly.com/question/28963056
#SPJ11
which of the following is a probable cause of relay-controlled equipment failing to start when the contactor is closed?
One contact not closing is a probable cause of relay-controlled equipment failing to start when the contactor is closed
Why is a contactor used?
Now you may ask, why do we need to use a contactor? Can't we just connect the motor to the PLC? The simple answer is no.Why? Because you don't want to connect a high-voltage electric motor directly to your expensive PLC. If there are any electric surges on the motor's side, the PLC cards will be damaged.Instead, we use a contactor to connect the PLC to the motor in an indirect and safe manner. What do we mean by "indirectly," you may wonder. All contactors, after all, have a low voltage coil. The PLC output is connected to this coil. This coil is typically powered by a 24-volt DC signal.When the coil is turned on, an electromagnetic field is created.
To know more about Contactor, click on the link :
https://brainly.com/question/28146701
#SPJ1
The Complete Question is:- Which of the following is a probable cause of relay-controlled equipment failing to start when the contactor is closed?
5. A continuous hot rolling mill has two stands. Thickness of the starting plate = 1.0 in. and width = 12.0 in. Final thickness is to be 0.5 in. Roll radius at each stand = 10 in. Rotational speed at the first stand = 20 rev/min. Equal drafts of 0.25 in. are to be taken at each stand. The plate is wide enough relative to its thickness that no increase in width occurs. Under the assumption that the forward slip is equal at each stand determine (a) speed v, at each stand and (b) forward slip s. (c) also determine the exiting speeds at each rolling stand if the entering speed at the first stand is 85 ft/min.
Answer:
(a) To determine the speed v at each stand, we can use the relationship between the forward slip, rotational speed, and rolling speed:
rolling speed = rotational speed × (1 - forward slip)
At the first stand, the thickness reduction is:
thickness reduction = draft / starting thickness = 0.25 / 1.0 = 0.25
The final thickness after the first stand is:
final thickness = starting thickness - thickness reduction = 1.0 - 0.25 = 0.75
The speed at the first stand is:
v1 = (π × 10^2 × 20) / (12 × 0.75) = 139.63 ft/min
At the second stand, the thickness reduction is again 0.25, and the final thickness is 0.5. The speed at the second stand is:
v2 = (π × 10^2 × 20) / (12 × 0.5) = 209.44 ft/min
(b) To determine the forward slip, we can use the formula:
forward slip = (rotational speed - rolling speed) / rotational speed
At the first stand:
forward slip1 = (20 - 139.63) / 20 = -5.98
At the second stand:
forward slip2 = (20 - 209.44) / 20 = -9.47
Note that the negative values indicate that the rolling speed is greater than the rotational speed, which is physically impossible. This suggests that the assumption of equal forward slip at each stand is not valid.
(c) The exiting speed at each rolling stand can be determined using the same formula as in part (a), but with the entering speed at the previous stand as the rolling speed:
At the first stand, entering speed = 85 ft/min:
v1 = 85 × (1 - (-5.98)) = 541.88 ft/min
At the second stand, entering speed = v1:
v2 = v1 × (1 - (-9.47)) = 922.57 ft/min
The crane's main frame, crawler track, and/or outrigger supports, boom sections, and attachments are all considered part of the structural integrity of lifting
Structural Integrity The crane's main body, crawler music and/or outrigger supports, boom sections, and attachments are all considered part of the structural integrity of lifting.
The crane's essential body and crawler tune are considered a part of the structural integrity of lifting. In areas wherein gentle floor poses a assist hassle, mats and/or blocking off need to be used to distribute a crane's load and to keep a stage stable condition.
A safe Load Indicator (SLI) or an automatic safe Load Indicator (ASLI) is a device that's established on cellular or portal cranes to alert the operator if the carry is exceeding the safe operating variety of the machinery.
To realize extra about structural integrity click here
brainly.com/question/24180542
#SPJ4
Which of these is NOT one of the preventive measures aimed at reducing motor vehicle accidents that are caused by poor decision making in young drivers?
driver "buddy systems"
None of the following is a preventive measure aimed at reducing motor vehicle accidents caused by poor decision-making in young drivers: driver “buddy systems”, increased penalties for violations of driving laws, or driver’s education classes.
The most effective measures to reduce motor vehicle accidents are for young drivers to be taught the rules of the road and to develop good decision-making skills. These measures include: using defensive driving techniques, limiting distractions while driving, avoiding driving while impaired, and understanding the risks of speeding or aggressive driving. Young drivers should also be taught the importance of wearing seatbelts, checking tire pressure and vehicle maintenance, and having emergency preparedness kits in their vehicles. Educating young drivers on these safety measures is essential to reduce motor vehicle accidents.
To learn more about Buddy :
https://brainly.com/question/30908546
#SPJ11
on initial climbout after takeoff and with the autopilot engaged, you encounter icing conditions. in this situation you can expect
If you encounter icing conditions during climb-out after takeoff and with the autopilot engaged, you can expect the autopilot to adjust the aircraft's pitch and power to maintain a constant airspeed, which may not be sufficient to prevent ice buildup on the wings and other critical surfaces.
What is the explanation for the above response?In such a situation, it is essential to take immediate action to ensure the safety of the flight.
This may include turning off the autopilot and manually adjusting the pitch and power to maintain a safe speed and altitude, activating the aircraft's anti-icing systems, and communicating with air traffic control to request clearance to climb to a higher altitude or change your flight path to avoid the icing conditions.
Learn more about Autopilot at:
https://brainly.com/question/20372893
#SPJ1
engineers are designing a system by which a falling mass imparts kinetic energy to a rotating uniform drum to which it is attached by thin, very light wire wrapped around the rim of the drum (fig. p9.64). there is no appreciable friction in the axle of the drum, and everything starts from rest. this system is being tested on earth, but it is to be used on mars, where the acceleration due to gravity is in the earth tests, when is set to 15.0 kg and allowed to fall through 5.00 m, it gives 250.0 j of kinetic energy to the drum. (a) if the system is operated on mars, through what distance would the 15.0 kg mass have to fall to give the same amount of kinetic energy to the drum? (b) how fast would the 15.0 kg mass be moving on mars just as the drum gained 250.0 j of kinetic energy?
a) The 15 kg mass has to fall through a distance of 13.2 m on Mars to impart 250 J of kinetic energy to the rotating uniform drum.
b) The speed of the 15 kg mass on Mars as the drum gains 250 J of kinetic energy is 9.22 m/s.
According to the problem statement provided, the question asks for the distance through which a 15kg mass has to fall on Mars to impart 250 J of kinetic energy to the rotating uniform drum and the speed at which the 15kg mass is moving on Mars as the drum gains 250 J of kinetic energy.
The expression for the kinetic energy of an object is given as:
KE = 0.5mv²
Where, Kinetic energy of an object is represented as KE, Mass of the object is represented as m, Velocity of the object is represented as v.
The work done by the 15 kg mass in imparting kinetic energy to the drum is given as:
Work done = Kinetic energy
The expression for work done is given as:
W = Fs
Where, Work done is represented as W, Force is represented as F, Displacement is represented as s.
If there is no appreciable friction in the axle of the drum, the force required to move the drum is given as the weight of the mass acting vertically downwards. Hence,
F = mg
Where, Mass of the object is represented as m, Gravity of the object is represented as g.
The expression for the work done is given as:
W = Fs ……… (1)
Let the distance through which the mass has to fall on Mars to impart 250 J of kinetic energy to the rotating uniform drum be represented as s. Therefore, work done in the system can be given as:
W = Fsg
Substituting the value of the force, the equation becomes:
W = mgs ……… (2)
the mass of the object, m = 15.0 kg
Distance of the fall on Earth, s = 5.00 m
Work done in the system, W = 250.0 J
The value of g on Earth, gE = 9.81 m/s²
The value of g on Mars, gM = 3.71 m/s²
From equation (1), work done can be written as: W = Fsg ……… (1)
From equation (2), work done can be written as: W = mgs ……… (2)
Equating equations (1) and (2),
Fsg = mgs ……… (3)
Cancelling out s from both sides of the equation,
Fg = mg ……… (4)
From equation (4), Acceleration due to gravity on Earth can be given as:
gE = gG = 9.81 m/s²
Acceleration due to gravity on Mars can be given as:
gM = gM = 3.71 m/s²
We know that, F = mg. Therefore, the expression for the force required can be given as:
F = m*gM ……… (5)
Substituting equations (4) and (5) in equation (3),
m*gM*s = m*gE*5.00 m
Solving for s,
s = gE/gM * 5.00 ms = (9.81 m/s²) / (3.71 m/s²) * 5.00 ms = 13.2 m
Therefore, the 15 kg mass has to fall through a distance of 13.2 m on Mars to impart 250 J of kinetic energy to the rotating uniform drum. Speed can be determined using the formula:
KE = 0.5mv²
Rearranging the above expression, we get,
v = sqrt(2KE/m) ……… (6)
From the problem statement, Mass of the object, m = 15.0 kg. The work done in the system, W = 250.0 J. Substituting these values in equation (6),
v = sqrt(2*250.0 J/15.0 kg)
v = 9.22 m/s
Therefore, the speed of the 15 kg mass on Mars as the drum gains 250 J of kinetic energy is 9.22 m/s.
Learn more about Speed and kinetic energy at : https://brainly.com/question/19891482
#SPJ11
Tech B says that a resistance reading on a lightbulb requires the DMM to behooked to each side of the bulb and the switch turned on. Who is correct?
Tech B is correct. When taking a resistance reading on a lightbulb, the Digital Multimeter (DMM) must be hooked up to each side of the lightbulb with the switch turned on. This is because in order for the DMM to measure the resistance of the lightbulb, there must be a complete circuit with current running through it.
To measure the resistance of the lightbulb, the DMM needs to measure the voltage drop across the bulb. This voltage drop can only be measured if there is a current flowing through the lightbulb.
So, when the switch is turned on, the current is flowing through the lightbulb, allowing the DMM to measure the voltage drop across it and, in turn, the resistance.
If the switch is off, there is no current flowing through the lightbulb, so the voltage drop across it will be zero and the DMM will be unable to measure the resistance of the bulb.
Therefore, Tech B is correct and the DMM must be hooked up to each side of the lightbulb with the switch turned on in order to take a resistance reading.
Both the Technicians have different opinions about the resistance reading on a lightbulb.
Tech A says that a resistance reading on a lightbulb requires the DMM to be hooked up to each side of the bulb, while Tech B says that the DMM should be hooked to each side of the bulb and the switch turned on.
For more such questions on Digital Multimeter
https://brainly.com/question/29512413
#SPJ11
In JavaGiven the array-based list (20, 30, 40, 50), what will the new array look like after the following operations?
ArrayListPrepend(list, 10)
ArrayListSearch(list, 25)
ArrayListRemoveAt(list, 2)
ArrayListSearch(list, 40)
The new array will look like this after the given operations: [10, 20, 50].
ArrayListPrepend(list, 10): In this operation, 10 is added at the beginning of the list, which makes the new array (10, 20, 30, 40, 50). ArrayListSearch(list, 25): In this operation, we try to find the element 25 in the list. Since there is no such element in the list, the function will return -1. So, the array remains unchanged as (10, 20, 30, 40, 50). ArrayListRemoveAt(list, 2): In this operation, the element at index 2 (i.e. 30) is removed from the list. So, the new array becomes (10, 20, 40, 50). ArrayListSearch(list, 40): In this operation, we try to find the element 40 in the list. It is present at index 2. So, the function will return 2. The array remains as (10, 20, 40, 50).Therefore, the new array will look like this after the given operations: [10, 20, 50].
Learn more about ArrayList: https://brainly.com/question/20464124
#SPJ11
Can someone explain to me how this circuit works?
In an electronic circuit, electrons exit the power source, travel via conductors, perform work in a load, and then return to the power source. The electrons move in a circular direction, which is why it is called a circuit.
How does a circuit work explain?
The conductor travels in a circle from the power source to the resistor and back to the power source. The existing electrons in the wire are moved around the circuit by the power source. This is referred to as a current. Electrons flow from the negative end of a wire to the positive end. A circuit diagram is a simplified depiction of an electrical circuit's components that uses either photos of the individual sections or standard symbols.
Learn more about circuit
https://brainly.com/question/27206933
#SPJ1
TRUE/FALSE. Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece.
The given statement "Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece" is False because the main reason behind dividing the project into bite-size pieces and estimating each piece is to get a more accurate estimate of the project.
By dividing the project into bite-size pieces and estimating each piece, we can know about the time, effort, resources required for each piece. This information helps us in getting an accurate estimate of the project. In the case of a large project, it is challenging to estimate the total time required for the project.
It is because there may be many uncertainties, risks, dependencies that can affect the project. In such cases, dividing the project into smaller pieces and estimating each piece helps us to consider these uncertainties, risks, dependencies, etc. and get an accurate estimate of the project.
So, the given statement that "Estimation is more accurate if done for the total time versus dividing the project into bite-size pieces and estimating each piece" is False.
For such more question on Estimation:
https://brainly.com/question/30543546
#SPJ11
3) A steel pin supporting a gondola lift is subjected to an axial stress expected to be 51 ksi with a standard deviation of 3 ksi. The steel has a Sy of 60 ksi and S. of 80 ksi, both with a standard deviation of 5 ksi. Material yielding is considered a failure and will require part replacement. An ultimate failure will result in the loss of 20 human lives. a) If there are 100,000,000 of these parts in service, how many lives would you predict to be lost? b) The cost of this part varies linearly with the cross-sectional area (for the same length part, to double the cross- sectional area requires twice as much steel and twice the cost) The stress experienced by this part varies inversely and linearly with the cross-sectional area (you can imagine part as being in pure tension). By what fraction would you increase the cost of the part?
The cost should be increased by 50% or 0.5 fraction.
If there are 100,000,000 of these parts in service, how many lives would you predict to be lost?
The cost of this part varies linearly with the cross-sectional area (for the same length part, to double the cross-sectional area requires twice as much steel and twice the cost) The stress experienced by this part varies inversely and linearly with the cross-sectional area (you can imagine part as being in pure tension).
By what fraction would you increase the cost of the part?
The probability of the steel pin to fail, P(f) can be computed by the following formula:
P(f) = P(S> Sy)
Where P(S> Sy) is the probability of stress exceeding the yield stress. The value of P(S> Sy) can be calculated as follows:
Z= (S - μ)/σZ = (60 - 51)/3= 3P(S> Sy) = P(Z > 3) = 0.0013
Z= (S - μ)/σZ = (80 - 51)/5= 5.8P(S> Sut) = P(Z > 5.8) = 0.0000041
The probability of yielding (failure) can be computed as:
P(failure) = P(Sy < S < Sut) = P(S > Sy) - P(S > Sut) = 0.0013 - 0.0000041 = 0.001296
The number of parts in service = N = 100,000,000
Expected number of failures = N * P(failure) = 100,000,000 * 0.001296 = 129,600 lives are expected to be lost
The cost of the part is proportional to the cross-sectional area, A. If we assume the cross-sectional area to be doubled, then the cost will be doubled too.The stress, S is inversely proportional to A.
Therefore if A is doubled, then S will reduce by half (1/2) that is:S1/S2 = A2/A1S2= S1 (A1/A2)S2= 51 ksi (2/1)S2= 102 ksi
The fraction by which we should increase the cost is given as:
(Cost at S1/Cost at S2)= (Area at S1/Area at S2)= (1/2) = 0.5
Therefore, the cost should be increased by 50% or 0.5 fraction.
Learn more about Fraction:
brainly.com/question/6201432
#SPJ11
Which of the following statements is correct?
a. In pure metals, dendritic growth represents the vast majority of the total growth.
b. When solid crystals form from a liquid, heat is absorbed.
c. The temperature of the liquid ahead of the solidification front is less than the freezing temperature.
d. Planar growth occurs by the movement of a smooth solid-liquid interface into the liquid
The correct statement is "When solid crystals form from a liquid, heat is absorbed." The correct option is B.
What is solidification?Solidification is the process of transforming a liquid or a gas into a solid. The structure and properties of the solidified body are controlled by the manner in which the transformation occurs. Solidification is usually accompanied by a reduction in volume, a rise in density, and a decrease in entropy.
The liquid freezes when the temperature reaches the freezing point. When the liquid is frozen, the temperature is lower than the melting point of the substance. When a liquid freezes, it releases heat energy.
When solid crystals form from a liquid, heat is absorbed. Arrangement of crystals during solidification Planar growth occurs when the smooth interface moves into the liquid, and dendritic growth occurs when the crystal branches out in various directions. Planar growth occurs when there is an even, stable interface with the solid and liquid phases.
The interface's smoothness is due to the absence of any differences or disturbances that can cause the interface to fluctuate or oscillate.
The correct statement is Option B.
Learn more about Solidification here:
https://brainly.com/question/21278640
#SPJ11
provide formulas for x(t)and y(t)that could possibly represent the parametric curve (x(t),y(t)). explain how your formulas could possibly represent the parametric curve (x(t),y(t)).
The given problem is asking for the formulas of x(t) and y(t) that could represent the parametric curve (x(t), y(t)).
What is parametric curve?
Parametric curve is the curve that is defined by equations of the form [tex]x=f(t)[/tex] , [tex]y=g(t)[/tex] where t is the parameter.
So, for a given value of t, x and y coordinates can be found by plugging in that value of t. Different values of t will give different points on the curve.
To find the formulas for x(t) and y(t), the following steps can be used:
Step 1: Identify the shape of the curve. Based on the shape of the curve, we can come up with the equation of the curve.
Step 2: Break the curve into x(t) and y(t) components.
Step 3: Choose a parameter to represent the curve. Typically, we use t as the parameter.
Step 4: Determine the x(t) and y(t) components of the curve based on the chosen parameter.
Step 5: Write the equations of x(t) and y(t).
The equations can be simple linear equations or more complex nonlinear equations.
For example, consider a circular path. The equation of a circle can be represented as [tex](x-a)^2+(y-b)^2=r^2[/tex]
Where a and b represent the coordinates of the center of the circle, and r is the radius of the circle.
To find x(t) and y(t), we can rewrite the equation of the circle as: [tex]x=a+r cos(t)[/tex] and [tex]y=b+r sin(t)[/tex]
where t is the parameter.
So, for different values of t, we can get different points on the circle.
Learn more about Parametric curve here:
https://brainly.com/question/30482587
#SPJ11
Which of the following Linux permissions would assign the owner full access, the group RX access, and everyone else read access.
A. chmod 664 foobar.sh
B. cacls 7467 foobar.sh
C. cacls u+rwx g+rx o+r
D. chmod 754 foobar.sh
Linux permissions would assign the owner full access, the group RX access, and everyone else read access. is D. chmod 754 foobar.sh.
What is Linux Permissions?Linux uses a permission structure to dictate who can read and write to different files, directories, and other resources. When files and directories are created in Linux, there is a set of rules that dictate who can access the contents of that file.
Linux permissions are divided into three distinct classes: user, group, and others.
The chmod command is a shell command that modifies the permissions on a file or directory. It stands for "change mode" and allows the user to modify the permission settings on a file. A permission is given to each file to decide which user can do what with the file, like read, write, and execute permission.
The permission is divided into three main parts: read, write and execute. The first part is for the owner, the second is for the group, and the third part is for everyone else. The chmod command uses a three-digit number to represent the permissions.
Each digit represents one of the groups of permissions, where the first digit is for the owner, the second digit is for the group, and the third digit is for everyone else.
Linux Permissions that assign the owner full access, the group RX access, and everyone else read access:
Therefore, the answer is D. chmod 754 foobar.sh.
Learn more about Linux at
https://brainly.com/question/30176895
#SPJ11
zone bit recording is how disk manufacturers ensure that a platter's outer tracks store as much data as possible.
Zone bit recording is how disk manufacturers ensure that a platter's outer tracks store as much data as possible. Zone bit recording (ZBR) is a disk layout method for accommodating more data on a single hard disk platter.
It works by allocating extra sectors (the smallest unit of data on a hard disk) to the outer tracks on a hard disk platter, which store data more efficiently than inner tracks. Because the data is more tightly packed together on the outer tracks, ZBR is often used in conjunction with smaller track widths, which are used to improve data throughput.
ZBR, when used in conjunction with other disk design enhancements such as smaller track widths, allows for the allocation of more data to the outer tracks on a hard disk platter, resulting in increased data storage capacity for the same physical platter size. In addition, ZBR improves data throughput by decreasing the amount of time required for disk heads to access data on the outer tracks, resulting in faster read and write times for files stored in these areas of the disk.
The primary disadvantage of ZBR is that it necessitates a non-linear hard disk drive layout, which makes file fragmentation and drive maintenance more complex. It can also make data recovery more difficult, especially if data on the outer tracks becomes corrupted or damaged in some way.
For more such questions on Zone bit recording
https://brainly.com/question/30331112
#SPJ11
(15 points) Case hardening of a steel (Fe-C alloy) gear with initial concentration of 0.10 wt.% C is accomplished by raising the composition 7 mm below the surface to at least 0.35 wt% C. An engineer has proposed elevating the surface concentration to 1.10 wt% C for 307.787 hours at 1,000 °C. Note that the diffusion coefficient of carbon in steel at 1,000 °C is 1.6x10-1 m²/s. What is the concentration of carbon in the steel at a distance 8 mm from the surface? Note: If point is close to tabulated value you can use value from table and avoid linear interpolation.
The concentration of carbon in the steel at a distance of 8 mm from the surface is 0.224 wt%.
Here's a step-by-step explanation:
1. First, convert the distance from the surface from millimeters to meters: 8 mm = 0.008 m.
2. Calculate the diffusion parameter (z) by dividing the distance by the square root of the diffusion coefficient multiplied by time: [tex]z = x / \sqrt(Dt)[/tex]
[tex]z = 0.008 m / \sqrt(1.6*10^(-1) *307.787 *3600)[/tex]
[tex]z = 0.008 / \sqrt(1.6*10^(-1) * 307.787 * 3600)[/tex]
[tex]z =0.112[/tex]
3. Consult the error function table to find the corresponding value for z ≈ 0.112, which is erf(z) ≈ 0.124.
4. Calculate the concentration of carbon at the specified depth using the initial concentration, surface concentration, and error function value:
[tex]C(x) = C_(initial) + (C_(surface) - C_(initial)) * erf(z)[/tex]
[tex]C(x) = 0.10 + (1.10 - 0.10 ) * 0.124[/tex]
[tex]C(x) = 0.10 + 1.00 * 0.124[/tex]
C(x)≈ 0.224 wt.%
The concentration of carbon in the steel at a distance of 8 mm from the surface is approximately 0.224 wt.%.
Learn more about steel at:
https://brainly.com/question/26217574
#SPJ11