A stress of 4.75 MPa is applied in the [007] direction of a unit cell of an FCC copper single crystal. Determine all the slip system that has highest resolved shear stress.

Answers

Answer 1

The {111}<123> slip system has the highest resolved shear stress of 4.52 MPa and is the most likely slip system to activate under the applied stress in the [007] direction.

To determine the slip systems with the highest resolved shear stress, we need to calculate the resolved shear stress on each of the slip systems in the [007] direction of the FCC copper single crystal.

There are a total of 12 slip systems in FCC crystals, but only 3 of them are active in the [007] direction. These 3 slip systems are:

1. {111}<110> slip system

2. {111}<112> slip system

3. {111}<123> slip system

To calculate the resolved shear stress on each slip system, we use the formula:

Resolved Shear Stress (RSS) = Applied Stress x Cos(Φ) x Cos(λ)

τ = σ * cos(φ) * cos(λ)

Where Φ is the angle between the slip plane and the applied stress direction, and λ is the angle between the slip direction and the applied stress direction.

For the {111}<110> slip system:
Φ = 54.7°, λ = 45°
RSS = 4.75 MPa x Cos(54.7°) x Cos(45°) = 1.28 MPa

For the {111}<112> slip system:
Φ = 35.3°, λ = 45°
RSS = 4.75 MPa x Cos(35.3°) x Cos(45°) = 2.46 MPa

For the {111}<123> slip system:
Φ = 10.8°, λ = 45°
RSS = 4.75 MPa x Cos(10.8°) x Cos(45°) = 4.52 MPa

To know more about the shear stress, click below.

https://brainly.com/question/31743836

#SPJ11


Related Questions




FeCl3 has a van't Hoff factor of 3. 400. What is the freezing point in °C)


of an aqueous solution made with 0. 5600 m FeCl3? (Kf for water is


1. 860 °C/m)

Answers

To determine the freezing point of an aqueous solution made with 0.5600 m FeCl3, we can use the equation ΔT = Kf * m * i, where ΔT is the change in freezing point, Kf is the cryoscopic constant for water, m is the molality of the solution, and i is the Van't Hoff factor.

Given that FeCl3 has a Van't Hoff factor of 3.400 and the Kf for water is 1.860 °C/m, we can substitute these values into the equation to calculate the freezing point change.

By subtracting the change in freezing point from the freezing point of pure water, we can determine the freezing point of the FeCl3 solution.

The freezing point depression equation is ΔT = Kf * m * i, where ΔT is the change in freezing point, Kf is the cryoscopic constant for water, m is the molality of the solution, and i is the Van't Hoff factor.

Given that the molality of the solution is 0.5600 m and the Van't Hoff factor of FeCl3 is 3.400, we can substitute these values into the equation:

ΔT = (1.860 °C/m) * (0.5600 m) * (3.400) = 3.5796 °C

The change in freezing point (ΔT) is calculated to be 3.5796 °C.

To find the freezing point of the FeCl3 solution, we need to subtract the change in freezing point from the freezing point of pure water, which is 0 °C:

Freezing point = 0 °C - 3.5796 °C = -3.5796 °C

Therefore, the freezing point of the aqueous solution made with 0.5600 m FeCl3 is approximately -3.5796 °C.

To learn more about Freezing point - brainly.com/question/31357864

#SPJ

Determine the [H3O+] concentration for a 0.200 M solution of HCl. Group of answer choices a. 1.00 × 10-1 M b. 4.00 × 10-1 M c. 2.50 × 10 -14 M d. 1.25 × 10-14 M e. 2.00 × 10-1 M

Answers

The pH value would be equal to -log(0.200) = 0.70.

To determine the [H3O+] concentration for a 0.200 M solution of HCl, we can use the equation for the dissociation of HCl in water:
HCl + H2O → H3O+ + Cl-

HCl is a strong acid, meaning it completely dissociates in water. Therefore, the concentration of H3O+ ions will be equal to the concentration of HCl.
So, the [H3O+] concentration for a 0.200 M solution of HCl is simply 0.200 M.


It's important to note that the [H3O+] concentration for a solution can also be calculated using the pH formula:
pH = -log[H3O+]

In this case, pH would be equal to -log(0.200) = 0.70.

To know more about [H3O+] concentration visit:

https://brainly.com/question/23314484

#SPJ11

when a secondary battery provides electrical energy, it is acting as a(n) ________ cell, and when the battery is recharging, it is operating as a(n) ________ cell.

Answers

When a secondary battery provides electrical energy, it is acting as a(n) galvanic cell, and when the battery is recharging, it is operating as a(n) electrolytic cell.

A galvanic or voltaic cell is a type of electrochemical cell that converts chemical energy into electrical energy through a spontaneous redox reaction. In a secondary battery, such as a rechargeable lithium-ion battery, this reaction is reversible, meaning that the battery can both discharge and recharge by reversing the direction of the current flow.

When a secondary battery is discharging, the chemical reactions inside the battery cause the transfer of electrons from the negative electrode (anode) to the positive electrode (cathode), creating an electrical current that can power an external device. This process is known as a galvanic or voltaic cell, and it is similar to the process that occurs in a primary battery.

Learn more about battery here:

https://brainly.com/question/25606438

#SPJ11

Use the Clausius-Clapeyron equation to calculate the molar enthalpy of vaporization of ammonia. Enter as kJ/mol to 2 decimal places. Vapor P = 1.86atm at -28.2°C; VP 2.33 atm at -6.4°C. R =8.314 J/mol K

Answers

Therefore, the molar enthalpy of vaporization of ammonia is 23.27 kJ/mol.

To calculate the molar enthalpy of vaporization of ammonia using the Clausius-Clapeyron equation, we first need to calculate the slope of the vapor pressure curve (dP/dT) for ammonia. This can be done using the two given data points:
ln(P2/P1) = (ΔHvap/R) x (1/T1 - 1/T2)
where P1 = 1.86 atm, T1 = -28.2°C = 244.95 K, P2 = 2.33 atm, and T2 = -6.4°C = 266.75 K.
Solving for ΔHvap, we get:
ΔHvap = (R x ln(P2/P1)) / ((1/T1) - (1/T2))
ΔHvap = (8.314 J/mol K x ln(2.33/1.86)) / ((1/244.95 K) - (1/266.75 K))
ΔHvap = 23,269.47 J/mol or 23.27 kJ/mol (rounded to 2 decimal places)
Therefore, the molar enthalpy of vaporization of ammonia is 23.27 kJ/mol.
Using the Clausius-Clapeyron equation, we can calculate the molar enthalpy of vaporization of ammonia. The equation is:
ln(P2/P1) = ΔHvap/R * (1/T1 - 1/T2)
First, convert the given temperatures from °C to Kelvin (K):
T1 = -28.2°C + 273.15 = 244.95 K
T2 = -6.4°C + 273.15 = 266.75 K
Next, convert the pressures from atm to Pa (1 atm = 101325 Pa):
P1 = 1.86 atm * 101325 Pa/atm = 188465.1 Pa
P2 = 2.33 atm * 101325 Pa/atm = 236056.25 Pa
Now, plug the values into the equation:
ln(236056.25/188465.1) = ΔHvap/8.314 * (1/244.95 - 1/266.75)
Solve for ΔHvap:
ΔHvap = 8.314 * ln(236056.25/188465.1) / (1/244.95 - 1/266.75)
ΔHvap = 23,466.5 J/mol
Now, convert the result to kJ/mol:
ΔHvap = 23,466.5 J/mol * (1 kJ/1000 J) = 23.47 kJ/mol
So, the molar enthalpy of vaporization of ammonia is 23.47 kJ/mol to 2 decimal places.

To know more about molar enthalpy visit:-

https://brainly.com/question/3207013

#SPJ11

Determine the concentration of urea in the saturated solution in terms of molarity. [urea]Trial #1 8.35 M OkTrial #2 7.98 M Ok

Answers

The concentration of urea in the saturated solution is not 8.35 M or 7.98 M.

To determine the concentration of urea in the saturated solution in terms of molarity, we need to know the solubility of urea. Solubility is defined as the maximum amount of a solute that can be dissolved in a solvent at a particular temperature and pressure. Urea has a solubility of 108 g/100 mL of water at room temperature.
To calculate the molarity, we need to know the molecular weight of urea, which is 60.06 g/mol. Using the solubility data, we can calculate the concentration of urea in the saturated solution in terms of molarity.
In Trial #1, the concentration of urea was found to be 8.35 M. This means that there were 8.35 moles of urea present in one liter of solution. To calculate the mass of urea in one liter of solution, we multiply the molarity by the molecular weight:
8.35 mol/L * 60.06 g/mol = 501.6 g/L
Since the solubility of urea is 108 g/100 mL of water, we can convert this to liters:
108 g/100 mL * 1 L/1000 mL = 0.00108 g/L
Dividing the mass of urea in one liter of solution by the solubility of urea gives us the fraction of urea that is dissolved:
501.6 g/L / 0.00108 g/L = 464444.44
This means that the solution is oversaturated and some of the urea will precipitate out.
In Trial #2, the concentration of urea was found to be 7.98 M. Using the same calculations, we can determine that the solution is also oversaturated:
7.98 mol/L * 60.06 g/mol = 479.8 g/L
479.8 g/L / 0.00108 g/L = 444814.81
The solubility of urea at room temperature is 108 g/100 mL of water, which means that the solution is oversaturated and some of the urea will precipitate out.

To know more about solubility refer: https://brainly.com/question/28170449?referrer=searchResults

#SPJ11

The value of AH for the concentration cell [the one with saturated Cu(O H),] is zero (since the overall reaction simply represents the mixing of the same solution at different concentrations), yet the cell produces an electrical potential. What is the driving force of the "reaction"? Use the measured potential of your concentration cell to calculate AGmixin

Answers

The driving force for the concentration cell is the difference in ion concentration between the two solutions. The calculated value of AGmixin depends on the measured potential and can be calculated using the formula AGmixin = -nFE.

In a concentration cell, the driving force for the reaction is the difference in ion concentration between the two solutions. The cell consists of two half-cells, each containing the same electrode and electrolyte, but at different concentrations. When these half-cells are connected by a salt bridge, ions flow from the higher-concentration half-cell to the lower-concentration half-cell, generating a flow of electrons and creating an electrical potential. While the value of AH for this reaction is zero, the change in Gibbs free energy (ΔG) is negative since the reaction proceeds spontaneously from higher to lower concentration. The calculated value of ΔG can be determined using the measured potential and the formula ΔG = -nFE, where n is the number of electrons transferred and F is Faraday's constant.

Learn more about concentration cell here:

https://brainly.com/question/14213618

#SPJ11

Use the periodic trends to predict the relative size of the following transition metals: Rh, Pd, Ag, Cd Enter your answers as 1,2, 3, and 4. A rank of "1" represents the smallest atom and a "4" represents the largest atom. Rh = Pd = Ag = Cd =

Answers

The periodic trends to predict the relative size of the transition metals: Rh, Pd, Ag, Cd are

Rh = Pd = 1 (smallest)Cd = 3Ag = 4 (largest)

The relative size of the transition metals can be predicted based on their position on the periodic table. As we move from left to right across a period, the atomic radius decreases due to an increase in the number of protons in the nucleus. However, as we move down a group, the atomic radius increases due to the addition of new electron shells.

Rhodium (Rh) and Palladium (Pd) are located in the same period (period 5) and group (group 10) on the periodic table, so they have similar atomic radii. Silver (Ag) is located one period below (period 6) and one group to the left (group 11) of Rh and Pd, so it has a larger atomic radius. Cadmium (Cd) is located in the same group (group 12) as Rh and Pd but one period below (period 5), so it has a larger atomic radius than Rh and Pd but smaller than Ag.

Therefore, the relative size of the transition metals can be ranked as follows:

Rh = Pd = 1 (smallest)Cd = 3Ag = 4 (largest)

Learn more about transition metals: https://brainly.com/question/29828769

#SPJ11

The average human requires 120. 0 grams of glucose (c6h12o6) per day. How moles of co2 (in the photosynthesis reaction) are required for this amount of glucose? The photosynthetic reaction is: 6 co2 + 6 h2o c6h12o6 + 6 o2​

Answers

To produce 120.0 grams of glucose through photosynthesis, approximately 4.0 moles of CO2 are required.

In the photosynthetic reaction, 6 moles of carbon dioxide (CO2) and 6 moles of water (H2O) react to produce 1 mole of glucose (C6H12O6) and 6 moles of oxygen (O2). To determine the moles of CO2 required for the given amount of glucose, we need to use the concept of stoichiometry.

The molar mass of glucose (C6H12O6) can be calculated by adding the atomic masses of its constituent elements: 6 carbon atoms (6 × 12.01 g/mol), 12 hydrogen atoms (12 × 1.01 g/mol), and 6 oxygen atoms (6 × 16.00 g/mol). Adding these masses gives a molar mass of 180.18 g/mol for glucose.

To find the moles of glucose, we divide the given mass of glucose (120.0 grams) by its molar mass: 120.0 g / 180.18 g/mol = 0.6667 moles.

Since the stoichiometric coefficient of CO2 in the reaction is 6, we know that for every mole of glucose produced, 6 moles of CO2 are consumed. Therefore, to produce 0.6667 moles of glucose, we would require 6 times that amount of CO2: 0.6667 moles × 6 = 4.0 moles of CO2.

Hence, to produce 120.0 grams of glucose through photosynthesis, approximately 4.0 moles of CO2 are required.To determine the moles of CO2 required for the synthesis of 120.0 grams of glucose (C6H12O6) through photosynthesis, we can use the balanced equation for photosynthesis: 6 CO2 + 6 H2O → C6H12O6 + 6 O2. By comparing the stoichiometric coefficients, we find that 6 moles of CO2 are needed to produce 1 mole of glucose. Therefore, to produce the given amount of glucose, we would require 6 times the moles of CO2, which is determined by dividing the given mass of glucose by its molar mass.

Explanation:

In the photosynthetic reaction, 6 moles of carbon dioxide (CO2) and 6 moles of water (H2O) react to produce 1 mole of glucose (C6H12O6) and 6 moles of oxygen (O2). To determine the moles of CO2 required for the given amount of glucose, we need to use the concept of stoichiometry.

The molar mass of glucose (C6H12O6) can be calculated by adding the atomic masses of its constituent elements: 6 carbon atoms (6 × 12.01 g/mol), 12 hydrogen atoms (12 × 1.01 g/mol), and 6 oxygen atoms (6 × 16.00 g/mol). Adding these masses gives a molar mass of 180.18 g/mol for glucose.

To find the moles of glucose, we divide the given mass of glucose (120.0 grams) by its molar mass: 120.0 g / 180.18 g/mol = 0.6667 moles.

Since the stoichiometric coefficient of CO2 in the reaction is 6, we know that for every mole of glucose produced, 6 moles of CO2 are consumed. Therefore, to produce 0.6667 moles of glucose, we would require 6 times that amount of CO2: 0.6667 moles × 6 = 4.0 moles of CO2.

Hence, to produce 120.0 grams of glucose through photosynthesis, approximately 4.0 moles of CO2 are required.

To learn more about photosynthesis click here, brainly.com/question/29764662

#SPJ11

The following chemical reaction takes place in aqueous solution: SnBr2(aq)+ (NH4), S(aq) →SnS(s)-2 NH 4 Br(aq) Write the net ionic equation for this reaction

Answers

The net ionic equation for the reaction is:  Sn2+(aq) + S2-(aq) → SnS(s)

The given chemical reaction takes place in aqueous solution:

SnBr2(aq)+ (NH4)2S(aq) →   SnS(s)-2  +  2 NH4Br(aq)

The total ionic equation is:

Sn2  +  2Br-  + 2(NH4)+    +   S2-   →  Sn2+   S2-  +  2(NH4)+    +   2Br-  

Here is the net ionic equation for the given chemical reaction:

Sn²⁺(aq) + S²⁻ (aq)  → SnS(s)

These are the ions that directly participate.

To know more about the net ionic equation, click below.

https://brainly.com/question/15466794

#SPJ11

Complete and balance the following half-reaction in basic solution Cr(OH)3(s) → CrO42-(aq) + 3 e- 02 D2+ 3+ 4+ 1 2 3 5 6 7 8 9 0 05 口 1. + ) (s) (1) (g) (aq) e е OH- H2O O Cr H+ H3O+ H Reset • x H2O Delete

Answers

To complete and balance the given half-reaction in basic solution:

Cr(OH)3(s) → CrO42-(aq) + 3e-

First, let's balance the Cr atoms by adding 3 Cr(OH)3 on the left-hand side:

3Cr(OH)3(s) → CrO42-(aq) + 3e-

Next, balance the O atoms by adding 6 OH- ions on the right-hand side:

3Cr(OH)3(s) + 6OH-(aq) → CrO42-(aq) + 3e-

To balance the H atoms, we can add 6 H2O molecules on the left-hand side:

3Cr(OH)3(s) + 6OH-(aq) → CrO42-(aq) + 3e- + 6H2O(l)

Finally, to balance the charges, add 3 OH- ions on the left-hand side:

3Cr(OH)3(s) + 9OH-(aq) → CrO42-(aq) + 3e- + 6H2O(l)

The balanced half-reaction in basic solution is:

3Cr(OH)3(s) + 9OH-(aq) → CrO42-(aq) + 3e- + 6H2O(l)

Please note that this is the balanced half-reaction, and it needs to be combined with another half-reaction to form the complete balanced redox equation.

Learn more about balancing redox reactions in basic solution

https://brainly.com/question/3471295?referrer=searchResults

#SPJ11.

1.) A hot-air balloon has a volume of 875 L. What is the original temperature of the balloon if its volume changes to 955 L when heated to 56 ∘C∘C?2.) To what volume must it be compressed to increase the pressure to 435 mmHg?

Answers

The hot-air balloon must be compressed to a volume of 1525 L to increase the pressure to 435 mmHg.

To solve for the original temperature of the hot-air balloon when its volume changes to 955L when heated to 56 degrees, we can use the formula:  
(V1/T1) = (V2/T2)
where V1 and T1 are the initial volume and temperature, and V2 and T2 are the final volume and temperature.


Substituting the given values, we have:
(875/T1) = (955/329)

Cross-multiplying and solving for T1, we get:
T1 = (875 x 329) / 955
T1 = 301 K

Therefore, the original temperature of the balloon was 301 K.

2.) To solve for the new volume of the hot-air balloon, we can use the formula:
P1V1 = P2V2
where P1 and V1 are the initial pressure and volume, and P2 and V2 are the final pressure and volume.

Substituting the given values, we have:
(760 mmHg)(875 L) = (435 mmHg)(V2)

Solving for V2, we get:
V2 = (760 mmHg x 875 L) / 435 mmHg
V2 = 1525 L

Therefore, the hot-air balloon must be compressed to a volume of 1525 L to increase the pressure to 435 mmHg.

For more numerical on change in volume: https://brainly.com/question/30584160

#SPJ11

.Write the formula for a complex formed between Zn2 and NH3, with a coordination number of 3.
Write the formula for a complex formed between Zn2 and OH–, with a coordination number of 4.

Answers

The formula for a complex formed between Zn2+ and NH3 with a coordination number of 3 is [Zn(NH3)3]2+. which are typically ions or molecules that have a lone pair of electrons that can be donated to the metal ion.

In the first complex, Zn2+ has a coordination number of 3, which means that it is surrounded by three NH3 ligands. The formula for this complex is [Zn(NH3)3]2+. The ammonia molecules act as monodentate ligands, meaning that they donate one lone pair of electrons to the metal ion. In the second complex, Zn2+ has a coordination number of 4, which means that it is surrounded by four OH- ligands. The formula for this complex is [Zn(OH)4]2-. The hydroxide ions act as bidentate ligands, meaning that they donate two lone pairs of electrons to the metal ion.

The formula for a complex formed between Zn²⁺ and NH₃ with a coordination number of 3 is [Zn(NH₃)₃]²⁺. The formula for a complex formed between Zn²⁺ and OH⁻ with a coordination number of 4 is [Zn(OH)₄]²⁻. The coordination number is the number of ligands (NH₃) bonded to the central metal ion (Zn²⁺). In this case, the coordination number is 3, so there are three NH₃ molecules bonded to the Zn²⁺ ion. The formula is written as [Zn(NH₃)₃]²⁺.
Similarly, the coordination number for the complex formed between Zn²⁺ and OH⁻ is 4. This means there are four OH⁻ ligands bonded to the Zn²⁺ ion. The formula for this complex is written as [Zn(OH)₄]²⁻.

To know more about molecules visit:

https://brainly.com/question/19556990

#SPJ11

Aldehydes are more reactive than ketones towards nucleophilic attack because of __________

Answers

Aldehydes are more reactive than ketones towards nucleophilic attack because of presence of a hydrogen atom Aldehydes have a carbonyl group (-CHO) which consists of a carbon atom double bonded to an oxygen atom and a hydrogen atom.

This hydrogen atom is very reactive and makes the carbonyl carbon atom more electrophilic and susceptible to nucleophilic attack. In contrast, ketones do not have a hydrogen atom attached to the carbonyl carbon atom, making it less reactive towards nucleophilic attack.



The presence of the hydrogen atom in aldehydes allows for the formation of a resonance stabilized intermediate during nucleophilic attack. The nucleophile attacks the carbonyl carbon atom, resulting in a tetrahedral intermediate with a negatively charged oxygen atom and a positively charged carbon atom.

The positive charge on the carbon atom is stabilized by resonance with the adjacent carbonyl oxygen atom and the hydrogen atom. This resonance stabilization increases the electrophilicity of the carbonyl carbon atom, making aldehydes more reactive towards nucleophilic attack.



In addition, the smaller size of aldehydes compared to ketones also contributes to their higher reactivity. The smaller size of aldehydes allows for a closer approach of the nucleophile to the carbonyl carbon atom, resulting in a stronger interaction and faster reaction.

Know more about Aldehydes here:

https://brainly.com/question/30665943

#SPJ11

Which of the following combinations would form a solution? 1) Water and ethanol II) Sand and table salt III) Oxygen and nitrogen IV) Oil and vinegar A) B) 11 C) III D) II and IV E) I and III

Answers

The correct option is D) II and IV, because the combinations that can form a solution are II and IV.

Which combinations in the given options would result in a solution?

Solutions are important in various scientific and everyday contexts, understanding the factors affecting solubility, and the principles behind the formation of solutions.

A solution is formed when two or more substances are uniformly mixed at the molecular level. In this case, water and ethanol (I) can form a solution because both are miscible and can mix together to form a homogeneous mixture.

Similarly, oil and vinegar (IV) can also form a solution known as an emulsion. Sand and table salt (II) do not form a solution as they are insoluble in each other. Oxygen and nitrogen (III) are both gases and can mix together but do not form a solution.

Therefore, the combinations that can form a solution are II and IV.

Learn more about solubility

brainly.com/question/31493083

#SPJ11

You need to make 10. 0 L of 2. 0 M KNO3. What molarity would the potassium nitrate solution need to be if you were to use only 5. 0 L of it?


O 4. 8 M


O 1. 0M


O 4. 0M


O 25 M

Answers

If you need to make 10.0 L of a 2.0 M KNO3 solution and instead use only 5.0 L of it, the molarity of the potassium nitrate solution would need to be 4.0 M.

The molarity (M) of a solution is calculated by dividing the moles of solute by the volume of the solution in liters. In this case, if you want to make a 2.0 M KNO3 solution with a volume of 10.0 L, you would need a certain amount of moles of KNO3. However, if you use only half the volume, 5.0 L, the same amount of moles of KNO3 would be dissolved in a smaller volume, resulting in a higher molarity. Therefore, to achieve the same amount of moles of KNO3 in the 5.0 L solution, the molarity would need to be double, which is 4.0 M.

To learn more about molarity, click here:

brainly.com/question/31545539

#SPJ11

Which of the following column is suitable for separating a mixture of five proteins (molecular weight: 300kDa, 150kDa, 100kDa, 75kDa, 50kDa, respectively)? (a) the column separating range is from 30-200 kDa (b) the column separating range is from 30-120kDa (c) the column separating range is from 130-200 kDa

Answers

The column separating range is from 30-200 kDa is suitable for separating a mixture of five proteins.

Based on the given options and the molecular weights of the proteins, the most suitable column for separating the mixture of five proteins would be:

(a) the column separating range is from 30-200 kDa

Here's why:

(a) covers a wide range of molecular weights, including four of the five proteins (150kDa, 100kDa, 75kDa, and 50kDa). The only protein not within this range is the 300kDa protein.
(b) covers a narrower range and would only be able to separate three of the proteins (100kDa, 75kDa, and 50kDa).
(c) has an even narrower range and would only be able to separate one protein (150kDa).

Therefore, option (a) is the most suitable column for separating the mixture of proteins as it includes the largest number of proteins within its separating range.

For more questions on molecular weights:

https://brainly.com/question/24191825

#SPJ11

Option (b) with a column separating range of 30-120 kDa would be suitable for separating the mixture of five proteins with molecular weights ranging from 50-300 kDa, as it covers the entire range of the proteins' molecular weights.

It would be possible to separate a combination of five proteins with molecular weights of 300kDa, 150kDa, 100kDa, 75kDa, and 50kDa using option (b) with a column separating range of 30-120 kDa. This is due to the column range's coverage of all the molecular weights in the mixture, which enables the separation of each protein according to its size. Option (a) with a 30-200 kDa column range is too broad, which might lead to poor resolution and insufficient protein separation. Option (c), which exclusively separates the biggest protein while leaving the lesser proteins unresolved, has a range of 130–200 kDa, which is too small. Therefore, the best option for separating this mixture of proteins is (b).

learn more about column separating range here:

https://brainly.com/question/31964009

#SPJ11

select the mechanism of which this is reminiscent, a proton is grabbed, while a pi bond is slammed down while a leaving group is booted out? a) SN^1. b) SN^2. c) E1. d) E2.

Answers

The E2 mechanism is a type of elimination reaction, which means that it involves the removal of two substituents from a molecule to form a double bond.

What is an elimination reaction?

The E2 mechanism is a type of elimination reaction, which means that it involves the removal of two substituents from a molecule to form a double bond. The reaction typically proceeds in a single step, in which a strong base (such as an alkoxide ion, hydroxide ion, or amide ion) abstracts a proton from the beta carbon (the carbon adjacent to the leaving group) while simultaneously the pi bond is formed and the leaving group is expelled.

The E2 mechanism is favored by the presence of a strong base, as a strong base can efficiently abstract the proton and facilitate the formation of the double bond. The reaction is also favored by a good leaving group, as the leaving group must be expelled in order to form the double bond. Common leaving groups in E2 reactions include halides (such as chloride, bromide, or iodide) and sulfonates (such as tosylate or mesylate).

The E2 mechanism is typically a bimolecular process, meaning that the rate of the reaction depends on the concentrations of both the substrate and the base. The stereochemistry of the reaction is typically anti, meaning that the leaving group and the proton that are being abstracted must be in a trans configuration for the reaction to proceed efficiently.

Overall, the E2 mechanism is an important tool for organic chemists, as it allows for the efficient formation of double bonds and the removal of leaving groups from molecules.

Learn more about elimination reaction

brainly.com/question/29695970

#SPJ11

Show that the initial rate law predicted by the reaction mechanism 6-12a-c, with the first step rate-limiting, is rate = 2k1[Cl2]. Assume that the Cl . produced in step (3) can be neglected initially. Please show step by step calculations and answer it completely Cl2 2Cl (6-12a) cl. + co cICo (6-12b) cico'+ Cl Cl,CO + Cl (6-12c)

Answers

The initial rate law predicted by the reaction mechanism 6-12a-c, with the first step rate-limiting, is rate = 2k₁[Cl₂], where [Cl₂] represents the concentration of Cl₂ and k₁ is the rate constant for the first step.

According to the given mechanism, the reaction proceeds through three steps: 6-12a, 6-12b, and 6-12c. The first step (6-12a) is assumed to be rate-limiting, meaning it is the slowest step and determines the overall rate of the reaction.

In the first step (6-12a), Cl₂ reacts to form two Cl radicals (Cl.). The stoichiometry of this step indicates that for every molecule of Cl₂ consumed, two Cl radicals are produced.

Since the rate of the reaction is determined by the rate of the slowest step (6-12a), the rate law is directly proportional to the concentration of Cl₂. Thus, the rate law can be written as rate = k₁[Cl₂], where k₁ is the rate constant for the first step.

As specified in the question, the rate law is rate = 2k₁[Cl₂] because two moles of Cl radicals are produced per mole of Cl₂ consumed in the first step (6-12a).

Therefore, the initial rate law predicted by the given reaction mechanism is rate = 2k₁[Cl₂].

learn more about rate law here:

https://brainly.com/question/31873163

#SPJ11

what volume of cl2 gas, measured at 684 torr and 39 ∘c , is required to form 29 g of nacl ?

Answers

We need 6.48 liters of [tex]Cl_2[/tex] gas at 684 torr and 39°C to form 29 g of NaCl.

To calculate the volume of [tex]Cl_2[/tex] gas needed to form 29 g of NaCl, we need to use stoichiometry and the ideal gas law. The balanced chemical equation for the reaction between [tex]Cl_2[/tex] and Na is:

[tex]Cl_2 + 2 Na - > 2 NaCl[/tex]

The molar mass of NaCl is 58.44 g/mol, so 29 g of NaCl corresponds to 0.497 mol. Therefore, we need 0.249 mol of [tex]Cl_2[/tex].

We need to convert the given temperature of 39°C to Kelvin by adding 273.15, giving us 312.15 K.

This gives us a pressure of 0.9 atm.

Plugging in the values, we get:

[tex]V = nRT/P = (0.249 mol) * (0.08206 L.atm/mol.K) * (312.15 K) / (0.9 atm)[/tex]

V = 6.48 L

To know more about molar mass, here

brainly.com/question/22997914

#SPJ4

For the balanced chemical reaction C3H8 + 5O2 → 3CO2 + 4H2O how many grams of C3H8 are needed to make 10.7 g of H2O? Express your answer to three significant figures.

Answers

We need 6.55 grams of C3H8 to produce 10.7 g of H2O in the given chemical reaction.

To solve this problem, we need to use stoichiometry and convert the given mass of H2O to the amount of C3H8 required.
First, we need to determine the mole ratio of H2O to C3H8 using the balanced chemical equation. From the equation, we can see that for every 4 moles of H2O produced, 1 mole of C3H8 is consumed. Therefore, the mole ratio of H2O to C3H8 is 4:1.
Next, we can use this ratio to calculate the moles of C3H8 required to produce 10.7 g of H2O.
moles of H2O = mass/molar mass = 10.7 g / 18.015 g/mol = 0.594 mol
moles of C3H8 = (moles of H2O) / (4 moles of H2O/1 mole of C3H8) = 0.594 mol / 4 = 0.149 mol
Finally, we can convert the moles of C3H8 to grams using its molar mass.
mass of C3H8 = (moles of C3H8) x (molar mass of C3H8) = 0.149 mol x 44.01 g/mol = 6.55 g
Therefore, we need 6.55 grams of C3H8 to produce 10.7 g of H2O in the given chemical reaction.
Answer more than 100 words: In this problem, we used stoichiometry to determine the amount of reactant required for a given amount of product in a chemical reaction. Stoichiometry is a branch of chemistry that deals with the quantitative relationships between reactants and products in a chemical reaction. In stoichiometry, we use the balanced chemical equation to determine the mole ratios between the reactants and products. This allows us to convert between moles of reactants and products and ultimately to determine the mass of reactants required for a given amount of product. Stoichiometry is an important tool in chemical calculations and is used in a variety of applications, including in the synthesis of chemicals, in industrial processes, and in environmental studies.

To know more about Chemical reaction visit:

https://brainly.com/question/29762834

#SPJ11

Vitamins A, D, E, and K are BEST absorbed with foods that are rich inA. calcium.B. fat.C. fiber.D. vitamin C.

Answers

Vitamins A, D, E, and K are best absorbed with foods that are rich in B. fat. These vitamins are fat-soluble, which means they require dietary fat to be properly absorbed and utilized by the body.

Vitamins A, D, E, and K are BEST absorbed with foods that are rich in fat. This is because these vitamins are fat-soluble, meaning they are better absorbed when consumed with fat. Foods that are rich in fat include avocado, nuts, seeds, oily fish, and olive oil. However, it is also important to note that these vitamins are also commonly found in foods that are rich in calcium, such as dairy products, which can help with bone health.

To know more about dietary fat visit:

https://brainly.com/question/30839467

#SPJ11

Human infants with 21-hydroxylase deficiency (congenital adrenal hyperplasia) produce excess _________ , and this results in defects of the ___________ .
a. androgens, testis
b. androgens, external genitalia
c. progesterone, ovary
d. cholesterol, heart
Its either A or B....not sure which one though.

Answers

Both options A and B are partially correct. Human infants with 21-hydroxylase deficiency produce excess androgens, which can result in defects of the external genitalia, as well as other symptoms such as adrenal hyperplasia and metabolic imbalances.

Androgens are a type of steroid hormone that includes testosterone and are important in male development, including the development of the testes and external genitalia. However, excess androgens can also affect female development and result in ambiguous genitalia. It is important to note that the excess androgens are produced from cholesterol, which is a precursor molecule for steroid hormones. In this condition, the excess androgens are produced due to a deficiency in an enzyme involved in the synthesis of cortisol and aldosterone, two other important steroid hormones.

To know more about androgens visit:

https://brainly.com/question/27303082

#SPJ11

Strontium naturally exists as 4 stable isotopes with masses of 84, 86, 87, and 88- Which statement is correct? Note: Strontium has an atomic number of 38 and an average atomic mass of 87.62 amu. A. Strontium-86 is the least abundant B. Strontium-84 is the least abundant. C. All strontium isotopes are equally abundant D. Strontium-88 is the least abundant.

Answers

Strontium naturally exists as 4 stable isotopes with masses of 84, 86, 87, and 88- . The correct statement is (B) Strontium-84 is the least abundant.

The statement is based on the information provided in the question, which states that strontium exists as four stable isotopes with masses of 84, 86, 87, and 88. The atomic mass of strontium is the weighted average of these isotopes, which is 87.62 amu. Since the atomic mass is closer to the mass of strontium-87, it suggests that this isotope is more abundant. Therefore, strontium-84 is the least abundant among the stable isotopes of strontium.

Option B is the correct answer.

You can learn more about Strontium  at

https://brainly.com/question/1581557

#SPJ11

42. for the reaction, 2no(g) cl2(g) à 2nocl(g), determine the rate of reaction with respect to [nocl].

Answers

The rate of reaction with respect to [NOCl] for the reaction 2NO(g) + Cl₂(g) → 2NOCl(g) is proportional to k[Cl₂].

To determine the rate of reaction with respect to [NOCI], we need to use the rate law expression for the given reaction. The rate law expression shows how the rate of reaction depends on the concentrations of the reactants.

The general form of the rate law is:

rate = [tex]k[A]^{x}[B]^{y}[/tex]

Where k is the rate constant, [A] and [B] are the concentrations of the reactants, and x and y are the orders of the reaction with respect to A and B, respectively.

For the given reaction, the rate law expression is:

rate = k[NOC₁]²[Cl₂]¹

This means that the rate of reaction depends on the square of the concentration of NOCI and the first power of the concentration of Cl₂.

To determine the rate of reaction with respect to [NOCI], we can use the following equation:

rate = k[NOC₁]²[Cl₂]₁

Divide both sides by [NOCI]²:

rate/[NOC₁]² = k[Cl₂]¹

The left side of the equation is the rate of reaction per unit concentration of NOCI squared, which is called the rate constant. Therefore, the rate of reaction with respect to [NOCI] is proportional to the rate constant times the concentration of Cl₂ raised to the first power.

Thus, the rate of reaction with respect to [NOCI] is proportional to k[Cl₂].

Learn more about rate of reaction: https://brainly.com/question/28566775

#SPJ11

The service sector in Jessica’s economy is dominant. Which sector is dominating Jessica’s country? Jessica lives in a sector economy. Could be one of the most important occupation in Jessica’s economy.

Answers

The service sector is dominant in Jessica's economy. The service sector refers to the portion of the economy that provides services rather than producing goods.

It includes various industries such as retail, healthcare, education, finance, hospitality, and more. Since the service sector is dominant in Jessica's economy, it means that a significant portion of the economic activity and employment is focused on providing services to consumers or other businesses. This indicates that the country relies heavily on service-based industries to drive economic growth and generate employment opportunities.

Given that Jessica lives in a sector economy, one of the most important occupations in her country would likely be related to the service sector. Occupations such as customer service representatives, healthcare professionals, educators, financial advisors, and hospitality workers could be crucial in driving the economy and meeting the needs of the population.

It is important to note that other sectors like the agricultural and industrial sectors may still exist in Jessica's country, but the dominance of the service sector suggests that it plays a central role in the economy.

Learn more about dominant  here

https://brainly.com/question/31454134

#SPJ11

Which of the following statements is true based on the map?

Answers

A map is simply a picture of a place, to put it simply. This has two significant implications that are occasionally overlooked: A map does not accurately represent reality. In the given map, Volcanoes occur frequently along the boundaries of all the oceans. The correct option is A.

A map is a representation of particular natural and man-made features on the whole or a portion of the surface of the earth on a flat piece of paper, at a specific scale, and with accurate elevations and relative geographic positions.

A volcano is an opening in a planet's or moon's surface through which material from the interior of the object, which is warmer than its surroundings, can escape. Eruption results from this material escaping.

Thus the correct option is A.

To know more about volcano, visit;

https://brainly.com/question/6568100

#SPJ1

Write the full electron configuration for S2- full electron configuration: What is the atomic symbol for the noble gas that also has this electron configuration? atomic symbol:

Answers

The full electron configuration for S2- is 1s2 2s2 2p6 3s2 3p6. The atomic symbol for the noble gas that also has this electron configuration is Ar, which stands for Argon.

Neutral sulfur (S) atom and then add 2 electrons to account for the 2- charge.

The atomic number of sulfur is 16, so a neutral sulfur atom has 16 electrons. The electron configuration for a neutral sulfur atom is:

1s² 2s² 2p⁶ 3s² 3p⁴

Now, to account for the 2- charge, we need to add 2 electrons to the configuration. This will give us:

1s² 2s² 2p⁶ 3s² 3p⁶

Therefore, This electron configuration corresponds to a noble gas, which is argon (Ar). The atomic symbol for the noble gas that has the same electron configuration as S2- is Ar.

To know more about electronic configuration refer here :

https://brainly.com/question/26084288

#SPJ11

how many moles of sodium hydroxide are present in 50.00 ml of 0.09899 m naoh?

Answers

There are approximately 0.00495 moles of sodium hydroxide present in the 50.00 mL solution.

To find the moles of sodium hydroxide (NaOH) in a 50.00 mL solution with a concentration of 0.09899 M, you can use the formula:

moles = volume (L) × concentration (M)

First, convert the volume from mL to L:

50.00 mL = 0.05000 L

Now, multiply the volume in liters by the concentration:

moles = 0.05000 L × 0.09899 M

moles ≈ 0.00495 mol

Therefore, there are approximately 0.00495 moles of sodium hydroxide present in the 50.00 mL solution.

To learn more about volume, refer below:

https://brainly.com/question/1578538

#SPJ11

A student mixed 0.60 g of ferrocene (molar mass = 186.04 g/mol) with 2.0 mL of acetic anhydride (molar mass = 102.09 g/mol, p = 1.082 g/mL) and a catalytic amount of phosphoric acid that produced 0.45 g of acetyl ferrocene (molar mass = 228.07 g/mol). After introducing 0.12 g of crude product mixture into a chromatography column, the student isolated 0.078 g of purified acetyl ferrocene. What is the percent recovery of acetyl ferrocene?

Answers

The percent recovery of acetyl ferrocene is 10.61% after introducing 0.12g of crude product mixture.

To find the percent recovery of acetyl ferrocene, we need to first calculate the theoretical yield of acetyl ferrocene. We can use the balanced chemical equation for the reaction:

ferrocene + acetic anhydride → acetyl ferrocene + acetic acid

From the equation, we can see that the molar ratio of ferrocene to acetyl ferrocene is 1:1. So, the number of moles of ferrocene used in the reaction is:

0.60 g / 186.04 g/mol = 0.003225 mol

The number of moles of acetyl ferrocene produced is also 0.003225 mol (assuming complete conversion). The mass of acetyl ferrocene produced is:

0.003225 mol x 228.07 g/mol = 0.735 g

So, the theoretical yield of acetyl ferrocene is 0.735 g.

The percent recovery of acetyl ferrocene is:

(0.078 g / 0.735 g) x 100% = 10.61%

To know more about calculating percent recovery: https://brainly.com/question/30765861

#SPJ11

what is the concentration of ammonia in a solution if 25.0 ml of a 0.116 m solution of hcl are needed to titrate a 100.0 ml sample of the solution?

Answers

The concentration of ammonia in the solution is 0.029 M. This is calculated by using the stoichiometry of the acid-base reaction between ammonia and HCl.

To determine the concentration of ammonia in the solution, we can use the stoichiometry of the acid-base reaction between ammonia (NH3) and hydrochloric acid (HCl). The balanced equation for this reaction is NH3 + HCl → NH4Cl. From this equation, we can see that one mole of ammonia reacts with one mole of HCl. Using the volume and concentration of HCl, we can find the moles of HCl that reacted, which will also be the moles of NH3. We then use the volume of the ammonia solution to calculate its concentration. Following these steps, the concentration of ammonia in the solution is 0.029 M.

Calculation steps:
1. Moles of HCl = Volume (L) × Concentration (M) = 0.025 L × 0.116 M = 0.0029 mol
2. Moles of NH3 = Moles of HCl (from stoichiometry) = 0.0029 mol
3. Concentration of NH3 = Moles of NH3 / Volume of solution (L) = 0.0029 mol / 0.1 L = 0.029 M

To know more about the concentration visit:

https://brainly.com/question/31442502

#SPJ11

Other Questions
in this lab, you will discover important facts about network communications by using ping or traceroute. itadmin has a configured ip address, but no default gateway addres Suppose that you have a reflection diffraction grating with n= 110 lines per millimeter. Light from a sodium lamp passes through the grating and is diffracted onto a distant screen.Part ATwo visible lines in the sodium spectrum have wavelengths 498 nm and 569 nm. What is the angular separation of the first maxima of these spectral lines generated by this diffraction grating?Express your answer in degrees to two significant figures. = specify the required torque rating for a clutch to be attached to a motor shaft running at 1750 rpm. the motor is rated at 54th power and is of the design be tight Push: Explain Newton's Third LawExplain how a rocket taking off can be an example of Newton's Third Law of Motion. when caring for the client with hepatitis b, which situation would expose the nurse to the virus? the principal goal of corporate-level strategy is to enable a company to which of the following would cause shrinkage? multiple choice locating the store at an inaccessible location not automating the checkout process miscounting merchandise high employee turnover export tariffs Use Green's Theorem to evaluate the line integral along the path C is the triangle with vertices (0,0), (2,0), and (2, 1) and the path is a positively oriented curve. C xy dx + y^5 dy Mount Rainier, in the state of Washington, isone of the snowiest places on Earth. Duringone winter snowstorm, a meteorologistpredicted 15 feet of snow at Mount Rainier.Another meteorologist predicted 156 inchesof snow. Which snow prediction is greater?By how much? Your opinion, which perspective is the better approach to regulating hatespeech: libertarian or communitarian? Explain why you believe this perspectiveto be the better approach. calculate the solubility in g/l of agbr in (a) pure water and (b) 0.0019 m nabr. create the integerarraymath class's integer division method(see the below code) the method: if the result of the division is an integer then print out a message indicating the result of the division such as 8/4 is 2. An equilateral triangle has a perimeter of 36 inches. What is the height of the triangle? Express your answer as a simplified radical. Two circular disks are parallel and directly facing each other. The disks are diffuse, but their emissivitys varies with wavelength. The properties are approximated with step functions as shown. The disks are maintained at temperatures 1 1200 K and 2 800 K. The surroundings are at = 400 K. Compute the rate of energy that must be supplied to or removed from the disks to maintain their specified temperatures. The outer surfaces of the disks are insulated so there is radiation interchange only from the inner surfaces that are facing each other. If the temperature of the copper was instead 1350 k, it would cause the water to boil. how much liquid water (latent heat of vaporization = 2.26 10^6 j/kg) will be left after the water stops boiling? Which of the following solutions would be expected to have a pH greater than 7.00? a)NH4Br b)C6H5NH3Br c)Ca(NO3)2 d)C6H5COONa A point charge q1=5.00Cq1=5.00C is held fixed in space. From a horizontal distance of 7.00 cm, a small sphere with mass 4.00103kg4.00103kg and charge q2=+2.00Cq2=+2.00C is fired toward the fixed charge with an initial speed of 36.0 m/sm/s. Gravity can be neglected.What is the acceleration of the sphere at the instant when its speed is 24.0 m/sm/s? In which areas did Reagan achieve his goals?Choose all answers that are correct.ResponsesEased tensions between the Soviet Union and the United States.Eased tensions between the Soviet Union and the United States.Cut taxes and some government social programs.Cut taxes and some government social programs.Increased funds for military expansion.Increased funds for military expansion.Balanced the national debt.The answers to the quiz are:1. Eased tensions between the Soviet Union and the United States.2. Increased funds for military expansion.3. Balanced the national debt.Hope this helps you with your quiz!Have a wonderful day ya'll :) AnalyteHClMole of Analyte (HCl)(Equal to the moles of titrant) Concentration (M)of analyte (HCl)Step 1- divide volume dispensed of analyte by 1000 to get L of analyteStep 2- Divide moles of analyte by liters of analyte to get concentration. Average concentration(M) of analyte. Add up the analyte concentrations from the three trials. Divide your answer by 3. Include 3 significant digits in your answer. Percent error of concentration (M) of analyte. Actual concentration of HCl = 0. 120 MExperimental concentration- Use the average you calculated. Step 1- Subtract experimental value from actual value. Step 2- Divide answer in Step 1 by actual value. Step 3- Multiply answer in Step 3 by 100. Your answer should be expressed as a percentage. Most trigonometric equations have unique solutions.true or false