A uniform beam of length L = 2.2 m and mass M = 49 kg has its lower end fixed to pivot at a point P on the floor, making an angle θ = 18° as shown in the diagram. A horizontal cable is attached at its upper end B to a point A on a wall. A box of the same mass M as the beam is suspended from a rope that is attached to the beam one-fourth L from its upper end.

What is the y-component Py of the force, in newtons, exerted by the pivot on the beam?

Write an expression for the tension T in the horizontal cable AB.

What is the x-component Px of the force, in newtons, exerted by the pivot on the beam?

I cannot figure part C

Answers

Answer 1

Hi there!

Part A.

To solve this part, all we need to do is a summation of vertical forces.

We have the following acting on the beam :
- Force of gravity (Fg, down)
- Force of tension from the rope holding the box (T, down)
- Force exerted by pivot (Py, up)

These sum to zero because the beam is not accelerating vertically.

[tex]\Sigma F = -F_g - T + P_y = 0[/tex]

[tex]P_y = F_g + T[/tex]

The tension force is equal to the box's weight because the forces on the box are balanced. Let's use values and solve.

[tex]P_y = 49(9.8) + 49(9.8) = \boxed{960.4N}[/tex]

Part B.

We must begin by doing a summation of torques. Placing the pivot point at the pivot, we have the following present:
- Force of gravity acting at the center of mass of the rod (CC, at L/2)

- The tension of the horizontal cable acting at the end of the rod (CCW, at L)

- The force of tension in the rope holding the box (CC, at 3L/4)


Since the rod is not rotating, these torques sum to zero.

The equation for torque is:
[tex]\tau = r \times F[/tex]

This is a cross-product, and you must find the lever arm (perpendicular distance between pivot and line of action of force). We will need to use trigonometry for this.

Now, let's find the torque from all three of these forces.

- Force of gravity at center:

The perpendicular distance between the force of gravity and the pivot point is the cosine with respect to the angle made with the floor.

[tex]\tau = Mg\frac{L}{2}cos(\theta) = 49(9.8)*\frac{2.2}{2} cos(18) = 502.367 Nm[/tex]

- Tension of horizontal cable:

The lever arm is the sine with respect to the angle. We will still have to solve for the value of 'T'.

[tex]\tau = TLsin\theta = T(2.2)sin(18) = 0.68T[/tex]

- Tension of rope holding box:
The tension is equal to the weight of the box since the box isn't accelerating. Thus, the torque would be:
[tex]\tau = Mg(\frac{3L}{4}) = 49(9.8)*\frac{3(2.2)}{4}cos(18) = 753.55 Nm[/tex]

Summing with clockwise torques + and counterclockwise -:
[tex]\Sigma \tau = 502.367 + 753.55 - 0.68 T = 0 \\\\1255.917 = 0.68T\\T = \boxed{1847.38 N}[/tex]

Part C.

This part is a lot easier than it seems. All we need to do is a summation of horizontal forces.

We only have two:
- The horizontal tension in the cable to the left (1847.38 N)

- The horizontal force exerted by the pivot on the beam to the right

These two balance out because there is no acceleration of the beam horizontally, so:
[tex]\Sigma F = P_x - T = 0 \\\\P_x = T\\\\P_x = \boxed{1847.38 N}[/tex]

**to the right

Answer 2

Answer:

a) 960.4 N

b) T= 5/4 Mg CotanΘ

c) 1847. 38

Explanation:

a) Py= 2Mg

=2(49 x 9.8)

= 960.4

b) T= (Mg x 1/2 x cos Θ + Mg x 3/4 x cos Θ) / sin Θ

T= 5/4 X Mg cotanΘ

c) T= (5/4) x (49 x 9.8) cotan (18)

T= 1847.37954

= 1847.38


Related Questions

Which statement best suscribes what happens during chemical change?

Answers

Chemical change involves the rearrangement of atoms or molecules in a substance, resulting in the formation of new substances with different properties than the original substance.

A chemical change in a chemical reaction is a process where one or more substances undergo a chemical transformation, resulting in the formation of new substances with different chemical and physical properties than the original substances. During a chemical change, the atoms or molecules of the reacting substances are rearranged through chemical reactions, leading to the breaking and forming of chemical bonds and the release or absorption of energy.

Chemical changes occur when a material's chemical makeup is changed, creating one or more new compounds with qualities that are distinct from those of the original substance. Chemical reactions that result in the breaking and building of chemical bonds occur when the atoms or molecules of the substances involved are reorganized during a chemical shift. The release or absorption of energy in the form of heat, light, or sound is typically accompanied by this process.

Therefore, Rearranging atoms or molecules in a substance causes chemical change, which creates new compounds with differing properties from the original one.

To learn more about redox reaction click:

brainly.com/question/2671074

#SPJ1

You will need to know that Force (N) is equal to mass (kg) multiplied by acceleration (m/s2) for this problem. A fearless space explorer has discovered a new planet with a frictionless surface! He pushes a large crate with a mass of 220kg a distance of 5.3 km, as he does so, it accelerates at a rate of 2m/s2. How much work has our intrepid hero done?

Answers

The intrepid hero has done 2.332 x Joules of work in pushing the crate.

To ascertain the work done by the traveler, we first need to find the power he applied on the case. As per Newton's subsequent regulation, force is equivalent to mass times speed increase, so the power applied by the traveler on the container is:

Force = mass x speed increase = 220 kg x 2  = 440 N

Then, we really want to work out the distance the case was moved. The pilgrim pushed the box a distance of 5.3 km, or 5,300 m.

At long last, we can compute the work done by the pioneer utilizing the equation:

Work = force x distance = 440 N x 5,300 m = 2.332 x 10^6 Joules

Thusly, the valiant legend has done 2.332 x  Joules of work in pushing the case.

The space pilgrim takes care of business on the case by applying a power that makes it speed up. The work done is equivalent to the power duplicated by the distance over which the power is applied. Involving the recipe for force, F=ma, and the given qualities for mass and speed increase, we can ascertain the power applied. Then, at that point, involving the recipe for work, W=Fd, and the given distance, we can ascertain the work done. The work done by the adventurer is 2.332 x  J.

To learn more about work, refer:

brainly.com/question/29167651

#SPJ1

A pizza delivery man has to lift a very large pizza a height of 3.85cm higher than he is already holding it to meet the outstretched arms of the customer. if it takes 116 kj of work on the pizza to lift it this high, what force does he exert on the pizza

Answers

Answer:

To solve this problem, we can use the formula:

Work = Force x Distance x cos(theta)

where Work is the amount of work done on the pizza, Distance is the distance the pizza is lifted, theta is the angle between the force and the displacement, and cos(theta) is the cosine of the angle between the force and displacement.

We are given that the work done on the pizza is 116 kJ, the distance the pizza is lifted is 3.85 cm (which is 0.0385 m), and the angle between the force and the displacement is 0 degrees (since the force is applied in the same direction as the displacement).

Plugging in these values, we get:

116 kJ = Force x 0.0385 m x cos(0)

Simplifying and converting the units of work to joules, we get:

116,000 J = Force x 0.0385 m

Solving for Force, we get:

Force = 116,000 J / 0.0385 m

Force = 3,012,987.01 N

Therefore, the delivery man exerts a force of approximately 3,012,987.01 Newtons on the pizza to lift it 3.85 cm higher.

PLEASE HELP

S
ai
5
The regular polygon has the following measures.
a = 9√3 m
s = 18 m
Segment a is drawn from the center of the polygon
perpendicular to one of its sides.
What is the vocabulary term for segment a?
What is the area of the polygon?
Round to the nearest tenth and include correct units.

Answers

Segment a, which is drawn from the center of the polygon perpendicular to one of its sides, is called the apothem.

The typical hexagon has a surface area of around 874.6 square meters.

How to determine area of a hexagon?

To find the area of a regular polygon, use the formula:

Area = (1/2) x Perimeter x Apothem

Find the perimeter of the polygon. Since the polygon has n sides, use the formula:

Perimeter = n x s

where s = length of one side.

Since s = 18m, find n by using the formula:

n = 360° / (180° - (360° / n))

where n = number of sides.

Plugging in the values:

n = 360° / (180° - (360° / n))

n = 360° / (180° - (360° / 6))

n = 6

So the polygon has 6 sides, which makes it a hexagon.

Now find the perimeter:

Perimeter = n x s

Perimeter = 6 x 18

Perimeter = 108m

Next, find the apothem, use the formula:

Apothem = s / (2 x tan(π/n))

Plugging in the values:

Apothem = 18 / (2 x tan(π/6))

Apothem = 9√3 m

Now use the formula for the area:

Area = (1/2) x Perimeter x Apothem

Area = (1/2) x 108 x 9√3

Area ≈ 874.6 m²

Therefore, the area of the regular hexagon is approximately 874.6 square meters.

Find out more on hexagon here: https://brainly.com/question/28821314

#SPJ1

I NEED HELP WITH THIS QUESTION

Answers

The charge R is positive and the charge L is negative hence, the correct option is option D.

The electric charges are of two types and they are positive and negative charge. There is an attractive force between the two charges. The electric field is formed around the charges and the electric field is denoted by using field lines around it.

The field lines are emerging from positive charge and end up in a negative charge. The field lines never intersect with each other. Hence, from the given, the field lines emerging from the positive charge(R) and end up in the negative charge(L).

Hence, the ideal solution is option D.

To learn more about charges:

https://brainly.com/question/14692550

#SPJ1

help me!!!!!!!
I want to know if I am correct or not

Answers

When the given wave pulse meets, then the diagram C represents the superposition of the pulses. Therefore, option C is correct.

The superposition of wave pulses refers to the phenomenon that occurs when two or more wave pulses are present in the same medium simultaneously. When these pulses overlap, their displacements combine to create a resultant wave.

The principle of superposition states that when waves meet, their displacements add algebraically at each point of overlap. This means that at any given point in space and time, the displacements of the individual waves are added together to determine the net displacement at that point.

Learn more about superposition, here:

https://brainly.com/question/12493909

#SPJ1

How can one sperate particles of different velocities moving in a magnetic field? ​

Answers

Magnetic particle separation is a powerful tool for separating particles based on their velocities in a magnetic field, and it has significant practical applications in various scientific and technological fields.

To separate particles of different velocities moving in a magnetic field, one can utilize a technique called magnetic field separation or magnetic particle separation.

This method takes advantage of the fact that charged particles moving in a magnetic field experience a force called the Lorentz force, which acts perpendicular to both the velocity vector and the magnetic field.

The basic principle behind magnetic particle separation is to apply a magnetic field perpendicular to the motion of the particles. The Lorentz force will then cause the particles to curve in different directions based on their velocities and charges.

By carefully controlling the strength and direction of the magnetic field, particles with different velocities can be steered onto different paths and separated.

One common approach to achieve magnetic particle separation is to use a device called a magnetic separator. This device typically consists of a strong magnet or a series of magnets arranged to create a uniform magnetic field.

The particles to be separated are injected into a chamber or a flow system where the magnetic field is applied. As the particles move through the magnetic field, they experience the Lorentz force and deviate from their original trajectory. The degree of deviation depends on their velocity and charge.

By carefully adjusting the magnetic field strength, particle size, and other parameters, it is possible to optimize the separation process and achieve effective separation of particles with different velocities. This technique has various applications in fields such as biomedical research, environmental monitoring, and materials science.

For more such questions on Magnetic particle visit:

https://brainly.com/question/31789735

#SPJ11

2. The second year of Peixotto Media's incorporation, the board of directors
announce that they will issue cash dividends to their shareholders. At this point,
shareholders own 70,000 shares of stock in the corporation. The dividends will be 10
cents per share.
a. How should Savannah journalize the declaration and payment of this dividend? (4
points)
b. Now, imagine that Peixotto Media had chosen to pay its shareholders a stock
Qividend instead of cash dividend. At the time, their stock is valued at $7.25 per
share. They choose to pay a 5 percent dividend. How would Savannah journalize the
declaration and payment of this dividend? (4 points)
c. Elena and Josh both own common stock in Peixotto Media. Elena owns 300
shares and Josh owns 75 shares. Compute the dividends payable to both
shareholders. Show your work. (2 points)

Answers

a. Savannah would debit retained earnings and credit dividends payable for the declaration of a cash dividend, and debit dividends payable and credit cash for the payment, b. To declare and pay a stock dividend, Savannah would debit retained earnings and credit common stock dividend distributable for declaration, then debit common stock dividend distributable and credit common stock for payment, and c. Dividends payable to shareholders like Elena and Josh can be computed by multiplying the number of shares owned by the dividend per share.

Dividends Payable is a liability account used to record the amount of dividends that a company owes to its shareholders but has not yet paid out. It represents the obligation of the company to pay out the declared dividend amount to its shareholders, and the balance is typically cleared out when the dividend payment is made. Companies usually set a record date and payment date to declare and pay dividends respectively.

a. To journalize the declaration and payment of the cash dividend, Savannah would make the following entries:

Declaration:

Debit: Retained Earnings

Credit: Dividends Payable

Payment:

Debit: Dividends Payable

Credit: Cash

b. To journalize the declaration and payment of the stock dividend, Savannah would make the following entries:

Declaration:

Debit: Retained Earnings

Credit: Common Stock Dividend Distributable (70,000 x 5% = 3,500 shares)

Payment:

Debit: Common Stock Dividend Distributable

Credit: Common Stock ($7.25 x 3,500 shares)

c. To compute the dividends payable to Elena and Josh, we would use the following formula:

Dividends Payable = Number of Shares x Dividend per Share

For Elena:

Dividends Payable = 300 shares x $0.10 per share = $30.00

For Josh:

Dividends Payable = 75 shares x $0.10 per share = $7.50

Therefore, To declare and pay a cash dividend, Savannah would debit retained earnings and credit dividends payable for declaration, and debit dividends payable and credit cash for payment. To declare and pay a stock dividend, Savannah would debit retained earnings and credit common stock dividend distributable for declaration, then debit common stock dividend distributable and credit common stock for payment. Dividends payable to shareholders like Elena and Josh can be computed by multiplying the number of shares owned by the dividend per share.

To learn more about Cash Dividends click:

https://brainly.com/question/31237280

#SPJ1

Hi
Please help on question asap if the answer is correct I'll rate you five stars a thanks and maybe even brainliest!

What do you notice about the values?

0.9 amps ÷0.03v=30 ohms.
1.9amps÷0.07v=27.149 ohms
3.1. amps ÷0.10v =31 ohms
3.9. amps ÷ 0.12v =032.5 ohms
5. amps ÷0.15v=33.33 ohms
6.1. amps ÷0.19v=32.1053 ohms

Answers

The resistance values from the givens are having a consistent value ranging from 27 to 33 ohms depending upon the supply of voltage and current.

Ohm's law gives the relation between the voltage, current, and resistance. Ohm's law states that the applied voltage is directly proportional to the current flow in the conductor. Thus, V∝I, V is the voltage and I is the current.

Ohm's law can also be written as, V = IR, where R is the resistance and the unit of resistance is ohm. The resistance is the factor that resists or opposes the current flow in the curcuit. When resistance increases, current flow in the circuit decreases and vice-versa.

From the given values, the resistance values changes when there is a change in voltage and current. The current and voltage have linear relationship, and these calculations make the idealsitic assumptions and can not hold true in practical applicaitons, when woeking with non-ohmic or non-linear components.

To learn more about Ohm's law:

https://brainly.com/question/14796314

#SPJ1

The diagram shows two sets of vectors that result in a
single vector.
R
100 m
200 m
250 m
50 m
What are the first two steps for finding the magnitude of
the resultant vector?
find the square of the first horizontal vector and the
square root of the first vertical vector
O find the square root of the first horizontal vector and
the square root of the second horizontal vector
O find the sum of the two horizontal vectors and the
sum of the two vertical vectors
O find the difference between the two horizontal vectors
and the difference between the two vertical vectors

Answers

The magnitude of the resultant vector is obtained by finding the sum of two horizontal vectors and the sum of two vertical vectors. Thus, option C is correct.

The resultant vector is the single vector that has the same effect in the number of vectors collectively produced. The resultant vector in the horizontal and vertical direction is obtained by drawing a diagonal and hence by using the Pythagoras theorem.

To find resultant vector is obtained by finding the sum of two horizontal vectors and vertical vectors and then using the Pythagoras theorem.

Thus, the ideal solution is option C.

To know more about Pythagoras' theorem:

https://brainly.com/question/343682

#SPJ1

If the magnification is -4 then is the image larger or smaller and is it inverted or upright

Answers

If the magnification is -4 the the image is larger and is it inverted in nature.

The magnification of the body is given is -4, here the signs show the nature of the image and the numerical value is the times to which the object has been magnified. Here, it is inverted because there is negative sign and it is enlarged as the magnification is more than 1.

Therefore, a magnification of -4 indicates that the image is both inverted and larger than the object. The resultant picture will be a larger, inverted version of the object if it is seen via a lens or mirror with a magnification of -4.

To know more about magnification, visit,

https://brainly.com/question/131206

#SPJ1

The side of a cube of metal is measured to be (1.00±0.06) cm and its mass is measured to be (41.0±0.4) g. Determine the uncertainty in the density of the solid in kilograms per cubic meter.

Answers

The density of the solid is (4.10 ± 0.78) × 10^3 kg/m^3.

To calculate the density of the cube below formula can be used:

ρ = m/V

where ρ is density, m is mass, and V is volume. For a cube, the volume is given by:

V = (side)^3

Therefore, the uncertainty in density can be calculated using the formula:

δρ/ρ = sqrt[(δm/m)^2 + 3(δs/s)^2]

where δρ is the uncertainty in density, δm is the uncertainty in mass, δs is the uncertainty in side, and s is the value of the side.

Now, putting in the given values:

s = (1.00 ± 0.06) cm = 0.01 ± 0.0006 m

m = (41.0 ± 0.4) g = 0.0410 ± 0.0004 kg

Volume, V = (0.01 m)^3

                  = 1.0 × 10^-6 m^3

Therefore, the density is:

ρ = m/V

  = 0.0410 kg/1.0 × 10^-6 m^3

  = 4.10 × 10^4 kg/m^3

Now substituting the values and calculating the uncertainty in density:

δρ/ρ = sqrt[(δm/m)^2 + 3(δs/s)^2]

δρ/ρ = sqrt[(0.0004/0.0410)^2 + 3(0.0006/0.01)^2]

δρ/ρ = 0.019

Therefore, the uncertainty in density is:

δρ = (0.019)(4.10 × 10^4 kg/m^3)

     = 779 kg/m^3

To know more about uncertainty in density refer to:

brainly.com/question/12971718

#SPJ1

A 250 kg cart is traveling at 8 m/s when it strikes a 100 kg cart at rest. After the elastic collision, the 250 kg cart continues to travel forward but at a lower velocity of 3 m/s. Determine the velocity of the 100 kg cart after the elastic collision.

Answers

Answer: In this scenario, we have two carts colliding with each other. One cart weighs 250 kg and is moving at a speed of 8 m/s, while the other cart weighs 100 kg and is initially at rest.

After the collision, the 250 kg cart continues moving forward, but at a slower speed of 3 m/s. We want to find out the speed at which the 100 kg cart moves after the collision.

To solve this, we use the principle that the total "push" or momentum before the collision should be the same as the total momentum after the collision.

Since the 100 kg cart is initially at rest, its momentum is zero. The momentum of the 250 kg cart before the collision is 250 kg * 8 m/s = 2000 kg·m/s.

After the collision, the momentum of the 250 kg cart becomes 250 kg * 3 m/s = 750 kg·m/s.

To find the momentum of the 100 kg cart after the collision, we subtract the momentum of the 250 kg cart after the collision from the total momentum before the collision: 2000 kg·m/s - 750 kg·m/s = 1250 kg·m/s.

Now, we divide this momentum by the mass of the 100 kg cart to find its velocity: 1250 kg·m/s / 100 kg = 12.5 m/s.

Therefore, the 100 kg cart moves at a velocity of 12.5 m/s after the collision, in the opposite direction of the 250 kg cart's motion.

A falling object accelerates from
-10.0 m/s to -30.0 m/s. How much
time does that take?
(Unit = s)
Remember: Falling = -v
a = -9.80 m/s²
Lost height = -Ay
Be careful with minus signs!!!/for acellus

Answers

It takes 2.04 seconds for the object to accelerate from -10.0 m/s to -30.0 m/s.

Velocity is a measure of an object's speed in a specific direction. It is calculated by dividing the distance traveled by the time taken and specifying the direction of the motion.

We can use the following formula to find the time taken for an object to change velocity under constant acceleration:

Δv = a × Δt

where Δv is the change in velocity, a is the acceleration, and Δt is the time taken.

In this case, the initial velocity is -10.0 m/s, and the final velocity is -30.0 m/s. So, the change in velocity is:

Δv = (-30.0 m/s) - (-10.0 m/s) = -20.0 m/s

The acceleration of the falling object is -9.80 m/s² (negative because the object is falling downward).

Now, we can rearrange the formula to solve for Δt:

Δt = Δv / a

Substituting the values we have:

Δt = (-20.0 m/s) / (-9.80 m/s²) = 2.04 seconds

Therefore, The object accelerates from -10.0 m/s to -30.0 m/s in 2.04 seconds.

To learn more about angular acceleration click:

brainly.com/question/30238727

#SPJ1

List the following in order of increasing mass: an atomic nucleus, a cell, an electron, a DNA molecule.

Answers

The order of increasing mass is:

An electron < An atomic nucleus < a DNA molecule < a cell.

     An electron is a fundamental particle with a negative charge and has a very small mass of order [tex]10^{-31}\ kg[/tex]. Which makes it the lightest in the group.

     An atomic nucleus consists of protons and neutrons which both individually have larger mass than an electron. The order of magnitude of the nucleus's mass is [tex]10^{-27}\ kg[/tex] or higher.

     A DNA molecule is a polymer chain of nucleotides and it carries genetic information. It contains many atoms, therefore it makes sense that it should have more mass than an atomic nucleus. Each human cell has about DNA of mass of order [tex]10^{15}\ kg[/tex].

     Lastly, A cell has the most mass in the given list since it encompasses everything else in the list.

Read more about cells and DNA here:

https://brainly.com/question/29059576

A plate of iron at 20 °C has shown in the figure below. If the temperature
raised to 100 °C and the coefficient of linear expansion of iron is 1.1 x 10-7 o
1, then what is the final area of the plate?
(5
2 m
2 m

Answers

The final area of the plate is 4.0000352 [tex]m^2[/tex] if the temperature raised to 100 °C and the coefficient of linear expansion of iron is 1.1 x 10-7.

Expecting that the plate of iron is rectangular, we can involve the recipe for warm extension of solids to compute the last region of the plate. The equation for direct warm development is given by ΔL = αLΔT, where ΔL is the adjustment of length, α is the coefficient of straight extension, L is the first length, and ΔT is the adjustment of temperature.

Since the region of the plate is given by A = L*W, where L is the length and W is the width, we can involve the equation for straight warm extension to compute the adjustment of length of the plate and afterward use it to compute the last region.

ΔL = αLΔT = [tex](1.1 x 10^-7 m/oC)(2 m)(80 oC) = 1.76 x 10^-5 m[/tex]

The last length of the plate is L + ΔL = 2 m + 1.76 x [tex]10^-5[/tex] m = 2.0000176 m (approx.)

The last width of the plate is thought to be unaltered as it isn't impacted by the adjustment of temperature.

Thusly, the last region of the plate is A = L*W = (2.0000176 m)(2 m) = 4.0000352 [tex]m^2[/tex] (approx.)

To learn more about linear expansion, refer:

https://brainly.com/question/14123289

#SPJ1

Car A is moving at a speed of 45km/h towards car B which is moving at a speed of 55km/h. if the two car were initially separated at a distance of 150km, determine how long it will take the two cars to meet?​

Answers

The time taken by the cars to meet is 5.4 x 10³ s.

Speed of car A, v₁ = 45 km/h = 12.5 m/s

Speed of car B, v₂ = 55 km/h = 15.27 m/s

Distance between the cars, d = 150 km = 15 x 10⁴m

The expression for the time taken by the cars to meet can be given as,

Time = Distance/Average speed

t = d/(v₁ + v₂)

Applying the values of d, v₁ and v₂.

t = 15 x 10⁴/(12.5 + 15.27)

t = 15 x 10⁴/27.77

t = 5.4 x 10³ s

To learn more about time taken, click:

https://brainly.com/question/14998000

#SPJ1

I need help. I don’t understand.

Answers

The voltage drop across R3 is 34.5 volts.

Voltage, also known as electric potential difference, is a measure of the difference in electric potential energy between two points in an electrical circuit, and it is measured in volts. It is the driving force that moves electric charges through a circuit, from a higher potential to a lower potential.

To determine the voltage drop across R3 in this circuit, we need to first find the equivalent resistance of R2, R3, and R4, since they are connected in parallel. We can then find the total resistance of the circuit by adding the equivalent resistance in series with R1, and finally use Ohm's Law to calculate the voltage drop across R3.

The equivalent resistance of R2, R3, and R4 in parallel can be calculated as:

1/R_parallel = 1/R2 + 1/R3 + 1/R4

1/R_parallel = 1/20 + 1/25 + 1/10

1/R_parallel = 0.15

R_parallel = 1/0.15

R_parallel = 6.67 ohm

The total resistance of the circuit can be found by adding R1 and the equivalent resistance in series:

R_total = R1 + R_parallel

R_total = 15 + 6.67

R_total = 21.67 ohm

Now we can use Ohm's Law to calculate the current flowing through the circuit:

I = ET / R_total

I = 30 / 21.67

I = 1.38 A

Finally, we can use Ohm's Law again to calculate the voltage drop across R3:

V_R3 = I * R3

V_R3 = 1.38 * 25

V_R3 = 34.5 V

Therefore, the voltage drop across R3 is 34.5 volts.

To learn more about Ohm's Law click:

brainly.com/question/1247379

#SPJ1

Push: Explain Newton's Third Law
Explain how a rocket taking off can be an example of Newton's Third Law of Motion.

Answers

Every action have equal and opposite reaction. for example when we fire bullet from a gun, the gun will recoil back and bullet moves forward. In case of rocket, rocket is fired, thrust is reaction of force applied by the gas on the floor.

A push or a pull that an object experiences as a result of interacting with another item is known as a force. Interactions result in forces! As was covered in Lesson 2, certain forces are the result of contact interactions (reaction, frictional, tensional, and applied forces are examples of contact forces), whilst other forces (gravitational, electrical, and magnetic forces) are the consequence of action-at-a-distance interactions. Newton postulated that whenever objects A and B interact, they exert forces on one another. You put a downward force on the chair when you sit on it, and the chair responds by exerting an upward force on your body. This contact creates two forces: one force on the chair and one force on your body.

To know more about force :

https://brainly.com/question/13191643

#SPJ1.

In the above example, the 9.012 represents the

Answers

The medium in which electromagnetic waves and mechanical waves travel is one of their primary distinctions. Light and other electromagnetic waves, including radio waves, can move through void space without the aid of a physical medium.

They may move through vacuum, air, or other materials and are made up of oscillating electric and magnetic fields. The propagation of mechanical waves, such as sound or water waves, on the other hand, depends on a physical medium.

To transport energy, they rely on particle interactions and displacements in the medium. Since mechanical waves need a physical medium to carry their energy, they cannot move through a vacuum.

To know more about wave :

brainly.com/question/27511773

#SPJ1.

A 24.0kg dog running at a speed of 3.0 m/s jumps onto a stationary skateboard that has a mass of 3.6 kg. How long will it take a force with a magnitude of 9.0N to stop the skateboard and dog?
Given: ?
Unknown: ?
Solve and show your work

Answers

The time will take a skateboard and dog with force 9N to stop the skateboard and dog is 8 seconds.

The force is defined as the push or pull of an object. The force equals the mass and acceleration of the object obtained from Newton's second law. Acceleration defines the change in velocity by the time taken. The force is defined as the rate of change of momentum and time. Momentum is defined as the product of mass and velocity and the unit of momentum is Kg.m/s.

From the given,

mass of dog (m) = 24 kg

The initial speed of dog (u) = 3 m/s

mass of skateboard and dog = 3 + 24 = 27 kg.

The final speed of dog (v) = 0 m/s

Force = 9N

time =?

F = dp/dt, rate of change of momentum and time.

F(dt) = dp

dt = (dp)/F

    =(Pf - Pi)/F

Pf is the final momentum and Pi is the initial momentum.

Pi = m×v = 24×3 = 72 kg.m/s²

Pf = m×v = 27×0 =0 kg.m/s²

dt = (0-72)/9

   = 8s

Thus, the time taken to stop the skateboard and dog is 8s.

To learn more about momentum:

https://brainly.com/question/30677308

#SPJ1

an object is placed in front of a spherical mirror of focal length -20 cm at a distance of 30cm. at what distance from the mirror a screen should be placed in order to get a sharp image of the object

Answers

The distance of the screen from the mirror should be 60 cm in order to get a sharp image of the object.

To find the distance of the screen from the mirror, we can use the mirror formula:

1/f = 1/v + 1/u

where f is the focal length of the mirror, u is the distance of the object from the mirror, and v is the distance of the image from the mirror.

In this case, the focal length is given as -20 cm (negative sign indicates that the mirror is a concave mirror), and the object is placed at a distance of 30 cm from the mirror. Therefore, we have:

1/-20 = 1/v + 1/30

Solving for v, we get:

v = -60 cm

The negative sign of the image distance indicates that the image is formed behind the mirror, which means it is a virtual image.

Now, to find the distance of the screen from the mirror, we can use the magnification formula:

m = -v/u

where m is the magnification of the image, which is given as -1 in this case (since the image is virtual and inverted), and u is the distance of the object from the mirror.

Substituting the values, we get:

-1 = -60/u

Solving for u, we get:

u = 60 cm

Therefore, the distance of the screen from the mirror should be 60 cm in order to get a sharp image of the object. It's important to note that this solution assumes that the mirror and screen are both perpendicular to the optical axis of the mirror, and that the object is small compared to the size of the mirror. If these assumptions are not true, the solution may be more complex.

For such more questions on image

https://brainly.com/question/16717342

#SPJ11

How many kilocalories of heat would be needed to melt 0.32 kg of ice at 0°C and increase the temperature to 25°C? The specific heat of water is 1 cal/g.°C, specific heat of ice is 0.5 cal/g.°C, the latent heat of ice to water is 80 cal/g. Keep one digit after the decimal.

Answers

To calculate the heat needed to melt the ice and raise the temperature, we need to break it down into two steps:

Step 1: Heat needed to melt the ice
The mass of ice is 0.32 kg, and the latent heat of ice to water is 80 cal/g. Therefore, the heat needed to melt the ice is:

0.32 kg x 80 cal/g = 25.6 kcal

Step 2: Heat needed to raise the temperature from 0°C to 25°C
The specific heat of water is 1 cal/g.°C, and the mass of water produced by melting the ice is also 0.32 kg. Therefore, the heat needed to raise the temperature from 0°C to 25°C is:

0.32 kg x 25°C x 1 cal/g.°C = 8 kcal

Total heat needed = Heat needed to melt the ice + Heat needed to raise the temperature
Total heat needed = 25.6 kcal + 8 kcal = 33.6 kcal

Therefore, 33.6 kilocalories of heat would be needed to melt 0.32 kg of ice at 0°C and increase the temperature to 25°C.

______________________________

A Stone Is Dropped Into a Deep Water Well. The Sound of The Stone Hitting The Water Is Heard After 3.4 Seconds. Determine The Depth of The Water Well.

N.B. The Correct Answer Will Receive 30 Points & The Brainliest Title.
______________________________​

Answers

A Stone Is Dropped Into a Deep Water Well. The Sound of The Stone Hitting The Water Is Heard After 3.4 Seconds. then The Depth of The Water Well is 56.6 m.

In terms of physics, sound is a vibration that travels through a transmission medium like a gas, liquid, or solid as an acoustic wave. Sound is the receipt of these waves and the brain's perception of them in terms of human physiology and psychology. Only acoustic waves with frequencies between about 20 Hz and 20 kHz, or the audio frequency range, may cause a human to have an auditory sensation. These correspond to sound waves in air with an atmospheric pressure of 17 metres (56 ft) to 1.7 centimetres (0.67 in) in wavelength. Ultrasounds are sound waves with a frequency higher than 20 kHz that are inaudible to humans. Infrasound refers to sound frequencies below 20 Hz. Animals of different species have different hearing ranges. Acceleration of the stone is 9.8 m/s²

according to kinematics,

s = ut + 1/2 at²

s =  1/2 ×9.8×3.4²

s = 56.6 m

To know more about Sound :

https://brainly.com/question/29707602

#SPJ1.

proof(how this formula comes )
vector
u.v=|u||v|cosβ

Answers

The formula you mentioned is known as the dot product formula or the scalar product formula. It is used to find the angle between two vectors u and v.

Let's start by defining the vectors u and v. Suppose we have two vectors u and v in a two-dimensional space.

u = (u1, u2)

v = (v1, v2)

The dot product of these vectors is defined as:

u . v = |u| |v| cos(β)

where |u| and |v| are the magnitudes of the vectors u and v respectively, and β is the angle between the vectors u and v.

Now, let's derive this formula. The dot product of two vectors u and v is given by:

u . v = (u1 × v1) + (u2 × v2)

The magnitude of a vector is given by:

|u| = sqrt(u1² + u2²)

|v| = sqrt(v1² + v2²)

We can use the dot product and magnitude equations to obtain:

cos(β) = (u . v) / (|u| × |v|)

Multiplying both sides by |u| × |v| gives us:

|u| × |v| × cos(β) = u . v

Therefore, we have derived the dot product formula:

u . v = |u| × |v| × cos(β)

This formula can be used to find the angle between two vectors u and v in any two-dimensional or three-dimensional space.

Learn more about dot product formula:

https://brainly.com/question/29785115

#SPJ1

The complete question is-

Write the proof of the formula

u.v=|u||v|cosβ

A hot water tap delivers water at the rate of 20kg per minute at 80°C. A cold water tap delivers cold water at the rate of 10kg per minute at 20 °C. If both tabs are open for 3 minutes, calculate the final temperature of the mixture of cold and hot water.​

Answers

The final temperature of the mixture of cold and hot water is 60°C.

To calculate the final temperature of the mixture of hot and cold water, we can use the principle of conservation of energy. The heat gained by the cold water is equal to the heat lost by the hot water.

Given:

Rate of hot water flow (m₁) = 20 kg/min

The initial temperature of hot water (T₁) = 80°C

Rate of cold water flow (m₂) = 10 kg/min

The initial temperature of cold water (T₂) = 20°C

Duration (t) = 3 minutes

Let's calculate the heat gained by the cold water and the heat lost by the hot water using the formula:

Heat gained = mass * specific heat capacity * temperature change

For the cold water:

Heat gained by cold water = m₂ * specific heat capacity * (final temperature - T₂)

For the hot water:

Heat lost by hot water = m₁ * specific heat capacity * (T₁ - final temperature)

Since the heat gained by the cold water is equal to the heat lost by the hot water, we can set up the equation:

m₂ * specific heat capacity * (final temperature - T₂) = m₁ * specific heat capacity * (T₁ - final temperature)

Let's substitute the given values and solve for the final temperature:

10 kg/min * specific heat capacity * (final temperature - 20°C) = 20 kg/min * specific heat capacity * (80°C - final temperature)

Simplifying the equation:

10 * (final temperature - 20) = 20 * (80 - final temperature)

10 * final temperature - 200 = 1600 - 20 * final temperature

30 * final temperature = 1800

final temperature = 1800 / 30

final temperature = 60°C

Therefore, the final temperature of the mixture of hot and cold water after 3 minutes will be 60°C.

For more such questions on temperature:

https://brainly.com/question/26866637

#SPJ8

which of the following is an example of a physical change of matter

Answers

An example of a physical change of matter is (c) Melting ice.

Explanation: Melting ice is an example of a physical change of matter. When ice melts, it undergoes a change in state from a solid to a liquid, but its chemical composition remains the same. The water molecules in ice rearrange themselves to form liquid water, but no new substances are formed. This change can be reversed by cooling the liquid water to below its freezing point, causing it to solidify back into ice. Physical changes do not involve a change in the chemical identity of the substance, only a change in its physical properties, such as shape, size, or state.

In contrast, options a) Burning wood, b) Digesting food, and d) Rusting iron involve chemical changes. Burning wood involves a chemical reaction where wood reacts with oxygen to produce carbon dioxide, water vapor, and ash. Digesting food involves the breakdown of complex molecules into simpler ones through chemical reactions in the body. Rusting iron is a chemical reaction where iron reacts with oxygen and moisture in the air to form iron oxide.

for more such questions on matter

https://brainly.com/question/3998772

#SPJ11

Note: The complete question is:

Which of the following is an example of a physical change of matter?

a) Burning wood

b) Digesting food

c) Melting ice

d) Rusting iron

Need some guidance and help

Answers

The image distance is the distance of the image formed to the lens.

option C.

What is an image distance?

The distance between the point of incidence of a lens and the point where the image is formed is called image distance.

The image distance, that is the distance of the image formed by a lens for a given object distance (u) and the focal length (f) of the lens, is given by the following lens formula;

1/f = 1/v  + 1/u

where;

f is the focal length of the lensu is the object distance - distance of the object to the lensv is the image distance - the distance of the image formed to the lens

Thus, based on the formula and explanation given above, we can conclude that object distance is the distance of the object to the lens and image distance is the distance of the image formed to the lens.

Learn more about image distance here: https://brainly.com/question/12629638

#SPJ1

The image below shows sound waves traveling through air.
Which point is the source of the sound?

Answers

The point on the image that is the source of the sound / sound waves travelling would be B. 2.

Where do sound waves originate ?

When a sound is produced, such as a musical note or spoken word, it initiates a disturbance at the source, which sets the surrounding particles in motion. As these particles oscillate back and forth, they generate regions of compression and rarefaction, resulting in the formation of longitudinal waves.

The propagation of sound waves emanates from a central source, radiating outward in a spherical pattern, thereby creating an expanding wavefront. This fundamental principle of wave behavior stems from the point-source nature of sound waves, wherein they originate from a central locus and disperse in all directions.

This central source in the image is 2.

Find out more on sound waves at https://brainly.com/question/15680946

#SPJ1

2. How much heat energy is required to change an ice cube of mass m=720g from ice at a temperature of -10˚C to water at temperature of 15˚C? (specific heat capacity of ice=2220J/kgK, specific heat capacity of water=4187J/kgK and the latent heat fusion of ice=3330J/K)​

Answers

The amount of heat required to change the ice cube of mass 720 g from ice at a temperature of -10 ˚C to water at temperature of 15 ˚C is 300963.6 J

How do i determine the heat required?

First, we shall obtain the heat required to change the ice from -10 ˚C to 0 °C. Details below:

Mass of ice (M) = 720 g = 720 / 1000 = 0.72 KgInitial temperature of ice (T₁) = -10 °CFinal temperature of water (T₂) = 0 °CChange in temperature of water (ΔT) = 0 - (-10) = 10 °CSpecific heat capacity of ice (C) = 2220 J/KgKHeat (H₁) =?

H₁ = MCΔT

H₁ = 0.72 × 2220 × 10

H₁ = 15984 J

Next, we shall obtain the heat needed to melt the ice. Details below:

Mass of ice (m) = 0.72 KgLatent heat of fusion (ΔHf) = 333000 J/KgHeat (H₂) =?

H₂ = m × ΔHf

H₂ = 0.72 × 333000

H₂ = 239760 J

Next, we shall determine the heat required to change the water from 0 °C to 15 °C. Details below:

Mass of water (M) = 0.72 KgInitial temperature of water (T₁) = 0 °CFinal temperature of water (T₂) = 15 °CChange in temperature of water (ΔT) = 15 - 0 = 15 °CSpecific heat capacity of water (C) = 4187 J/gK Heat (H₃) =?

H₃ = MCΔT

H₃ = 0.72 × 4187 × 15

H₃ = 45219.6 J

Finally, we shall determine the heat required to change the ice from -10 ˚C to water at temperature of 15 ˚C Details below:

Heat required to change the ice from -10 ˚C to 0 °C (H₁) = 15984 JHeat required to melt the ice (H₂) = 239760 JHeat required to the water from 0 °C to 15 °C (H₃) = 45219.6 JTotal heat required (Q) =?

Q = H₁ + H₂ + H₃

Q = 15984 + 239760 + 45219.6

Q = 300963.6 J

From the above calculations, we can conclude that the heat required to change the ice from -10 ˚C to water at 15 ˚C is 300963.6 J

Learn more about heat transfer:

https://brainly.com/question/25878495

#SPJ1

Other Questions
6. Write a recursive function named search that takes as input the pointer to the root of a binary tree (not a BST!) and a value K, and returns true if the value K is found and false otherwise. (5 pts) Let f be a differentiable function such that f(0)=5. 420 and f(x)=sin2x+x. What is the value of f(2) ? 2Select the correct answer from each drop-down menu.Triangle ABC is shown in the coordinate plane. It is translated 6 units left and 4 units down. Then it is dilated by a scale factor of 3 centered about theorigin. Complete the statements.-6 -4v.64-2-lo-2--4--6-The translation of triangle ABCA26BResetThe dilation of triangle ABCNext which attack enables a penetration tester to duplicate access cards and is of particular value during physical penetration tests? a solution contains 4.5 x 10-6 m concentration of agno3 . determine the maximum concentration of nacl that can be added before a precipitate will form. who can help me solve this pls need help 2) if the demand for two products has the same standard deviation, does it necessarily mean they show the same uncertainty in demand If all of the angles in the pentagon below are congruent (equal), then what is the mA) 77B) 97C) 108D) 120 long leg boneItemunmarked stoneschipped stones with regular patternanimal bones with sharp tooth marksanimal bones with long groovessmall patches of sootEvidence of Humans?Yes/No/MaybeIWhy? evaluate the different systems development methodologies. which one would have most significantly increased the chances of the projects success? a local fm radio station broadcasts at a frequency of 95.6 mhz. calculate the wavelngth Use the Alternating Series Test, if applicable, to determine the convergence or divergence of the series.[infinity]n = 3(1)nnn2 5 et x[n] be the following sequence of duration N = 12: - a[n] = { x n] s 6 cos(81n), 0 does anyone know why I can't move passed ambitious level in Brainly I have 4222 points and 8 crowns For a methane molecule, find the irreducible representations using the four C-H bonds as a basis. Answer the following questions based on this questions: Continued from Problem 4 in Homework #2. (a) What orbitals on the central C atom will be used to form the bonds in CH4? (b) Could d orbitals on the C atom play a role in orbital formation in CH4? Explain why or why not. (c) In SiH4, could d orbitals be used to form the bonds? If so, which d orbitals? Structuralism and semiotics have focused on which of the following film traits?Select one:a. Signs rather than shotsb. Types of codesc. Deep structuresd. All of the above the type of blood vessel with thin walls that serves as a passageway and blood reservoir from organs to the heart are the the bond is administered by an independent trustee and includes information on pledged and methods of repayment. Question 1: There is a project with the following cash flows: Year 0 -$24,450 Year 1 $7,100 Year 2 $8,200 Year 3 $7,150 Year 4 $7,750 Year 5 $6,700 What is the payback period? Question 2: Blinding Light Co. has a project available with the following cash flows: Year 0 -$34,110 Year 1 $8,150 Year 2 $9,810 Year 3 $13,980 Year 4 $15,850 Year 5 $10,700 What is the project's IRR? Question 3: A company has a project available with the following cash flows: Year 0 -$34,070 Year 1 $12,810 Year 2 $14,740 Year 3 $20,220 Year 4 $11,480 If the required return for the project is 8.7 percent, what is the project's NPV? Write a recursive method to compute the following series: m(i)= 1 + 1/2 + 1/3 + ... + 1/i Write a test program that displays m(i) for i = 1, 2, . . ., X each on it's line and where X is entered by the user. output most look like this. Enter the last positive integer you .want .m (i).to be calculated for 23 m(1) 1.00 H J m(2) 1.50 m(3) 1.83 m(4) 2.08 m (5) 2.28 H m(6) 2.45 J (7) 2.59 J m m(8) 2.72 m(9) 2.83 m(10) 2.93 m (11) 3.02 (12) 3.10 m(13) 3.18 m(14) 3.25 m (15) 3.32 m(16) 3.38 (17) 3.44 m(18) 3.50 m (19) J. 3.55 (20) 3.60 m(21) 3.65 m(22) 3.69 (23) 3.73