An electric water heater consumes 7.13 kw for 3.10 h per day. what is the cost (in dollars per year) of running it for one year if electricity costs 13.6 cents/(kw · h)?

The index of refraction for the unknown material is approximately 1.931.

To find the index of refraction for the unknown material, you can use Snell's Law, which states:

n₁ * sin(θ₁) = n₂ * sin(θ₂)

In this case, n₁ is the index of refraction for air, which is approximately 1.00. θ₁ is the angle of incidence (36°), n₂ is the index of refraction for the unknown material, and θ₂ is the angle of refraction (18°).

Following the formula, you can plug in the values:

1.00 * sin(36°) = n₂ * sin(18°)

Now, divide both sides by sin(18°) to solve for n₂:

n₂ = (1.00 * sin(36°)) / sin(18°)

Calculate the values:

n₂ ≈ 1.931

To know more about refraction referhttps://brainly.com/question/14760207

#SPJ11

The dimensions of the box that maximize its volume 20.84 cubic feet..

Let the dimensions of the rectangle be 2x and 3x, so the area of the rectangle is:

2x * 3x = [tex]6x^2[/tex]

We know that the area of the board is 20 sq ft, so:

[tex]6x^2[/tex] = 20

Solving for x, we get:

x = sqrt(20/6) = 1.825

So the dimensions of the rectangle are:

2x = 3.65 ft (width)

3x = 5.475 ft (length)

To maximize the volume, we need to make the height of the box as large as possible, subject to the constraint that the area of the board is 20 sq ft. Let h be the height of the box.

The volume of the box is given by:

V = (2x)(3x)(h) = [tex]6x^2h[/tex]

Substituting x = 1.825, we get:

V = 6(1.825)[tex]^2h[/tex] = 20.84h

To maximize V subject to the constraint that the area of the board is 20 sq ft, we use the area formula to solve for h:

(2x)(3x) + 2(2x)(h) + 2(3x)(h) = 20

Simplifying and solving for h, we get:

h = (20 -[tex]6x^2[/tex]) / (4x) = (20 - 6(1.825)^2) / (4(1.825)) = 2.416 ft

Therefore, the dimensions of the box that maximize its volume are:

Width = 3.65 ft

Length = 5.475 ft

Height = 2.416 ft

And the maximum volume of the box is: V = 20.84 cubic feet.

Therefore, 20.84 cubic feet is the dimensions of the box that maximize its volume.

To know more about Volume refer here :

https://brainly.com/question/14197390

#SPJ11

Required the corresponding peak current is 16.97 A.

The corresponding peak current can be calculated using the formula Ipeak = Irms * √2. Therefore, the peak current for a circuit breaker that trips at 12.0 A

RMS current would be Ipeak = 12.0 * √2 = 16.97 A (rounded to two decimal places). It's important to note that peak current represents the maximum instantaneous current that a circuit can handle, while RMS current represents the equivalent heating effect of a steady DC current. In other words, a circuit breaker is designed to protect against overloading caused by peak currents, which can be higher than the corresponding RMS current.

Learn more about current here,

https://brainly.com/question/30611906

#SPJ11

When the block of ice at 0°C melts in a beaker of ice water, the water level in the beaker will remain the same. This is because the volume of ice that is submerged in the water is equal to the volume of water displaced by the ice, and when the ice melts, it turns into water which occupies the same volume.

The correct option is  (B).

The mass of the ice is equal to the mass of the water it displaces, and since ice has a lower density than water, the volume of ice that is submerged in water is equal to the volume of water displaced by the ice.

When the ice melts, the water formed has the same volume as the ice, and hence the water level in the beaker remains the same.

To know more about volume refer here :-

https://brainly.com/question/1578538#

#SPJ11

The distance between the two stakes in horseshoe pitching is approximately 12.192 meters.

The given problem states that the two stakes in horseshoe pitching are 40 feet apart. And we are supposed to find out the distance between them in meters. Let us first write down the given value in feet.Given that the distance between the two stakes is 40 feet. Now, 1 meter is equivalent to 3.28084 feet.To convert feet into meters, we need to divide the given value of feet by the value of 3.28084.Thus, the distance between the two stakes in meters can be calculated as follows: Distance in meters = \frac{distance in feet }{ 3.28084 }

.Distance in meters =\frac{ 40 }{ 3.28084 meters} ≈ 12.192 meters.

Therefore, the distance between the two stakes in horseshoe pitching is approximately 12.192 meters. The exact value can be obtained by using more number of decimal points.

learn more about distance Refer: https://brainly.com/question/30195100

#SPJ11

Some materials can become strongly magnetized. The correct answer is B) The fields of the individual electrons due to the property of electron spin is believed to be the microscopic cause of the macroscopic magnetic field in such materials

In materials that can become strongly magnetized, the macroscopic magnetic field is believed to be caused by the microscopic behavior of electrons and their intrinsic property called "electron spin." Electron spin is not the same as the physical spinning motion of an electron but rather a fundamental quantum property related to its intrinsic angular momentum.

When a material becomes magnetized, it means that the magnetic moments of individual electrons align in a particular direction, creating a net magnetic field. This alignment occurs due to the behavior of electron spins within the material.

The magnetic moment associated with electron spin generates a magnetic field around the electron. In materials that can be magnetized, the collective behavior of these individual electron spins aligns, leading to a net magnetic field that can be observed at the macroscopic level.

The other options listed:

A) The fields from electrons orbiting the nucleus that behave like current loops: While electrons in atoms do have orbital motion around the nucleus, this motion alone does not generate a macroscopic magnetic field. Orbital motion contributes to atomic magnetism but is not the primary cause of the macroscopic magnetic field observed in magnetized materials.

C) The fields caused by polarization of the atoms in an electric field: This refers to electric polarization, not magnetic field generation. Electric polarization occurs when positive and negative charges separate in response to an external electric field, but it does not directly lead to the creation of a macroscopic magnetic field.

D) The fields caused by sharing of electrons in the bonds between atoms: This statement refers to electron sharing in covalent bonds, which is relevant to chemical bonding but not the primary cause of macroscopic magnetic fields.

In summary, the alignment of individual electron spins in materials with strong magnetization is believed to be the microscopic cause of the macroscopic magnetic field observed. This alignment of electron spins leads to a net magnetic moment and gives rise to the magnetic properties of such materials.

To know more about magnetic field, please click on:

https://brainly.com/question/30331791

#SPJ11

Balloon A is positively charged, and balloon C is negatively charged. If balloon A approaches balloon C, there will be an electrostatic force of attraction between them.

When two objects carry opposite charges, they exert an attractive force on each other. This force is known as the electrostatic force and follows Coulomb's law. According to Coulomb's law, the magnitude of the electrostatic force between two charged objects is directly proportional to the product of their charges and inversely proportional to the square of the distance between them. In this scenario, since balloon A is positively charged and balloon C is negatively charged, they have opposite charges. Therefore, the electrostatic force between them will be attractive. The magnitude of the force depends on the charges of the balloons and the distance between them. It is important to note that without specific information about the charges of the balloons and their distance, it is not possible to determine the exact magnitude of the force. To calculate the force, you would need the values of the charges and the distance between the balloons.

For such more questions on electrostatic

https://brainly.com/question/30388162

#SPJ11

The current of 4.91 A would need to be applied for 1.44 hours to plate out 8.40 g of copper, using the equation Q = I * t.

The amount of copper of electroplating that can be plated out from the Cu(NO3)2 solution depends on the amount of charge passed through the solution, which is directly proportional to the current and the time for which it is applied. The equation that relates the amount of charge passed (Q), the current (I), and the time (t) is Q = I * t.

To calculate the time required to plate out 8.40 g of copper, we need to first calculate the amount of charge required. The molar mass of Cu is 63.55 g/mol, which means that 8.40 g of copper is equivalent to 8.40/63.55 = 0.132 mol of copper. Each copper ion (Cu2+) requires 2 electrons to be reduced to copper metal. Therefore, the amount of charge required to plate out 0.132 mol of copper is:

Q = 2 * 0.132 * 96500 = 25452 C

where 96500 is the Faraday constant.

Now, we can use the equation Q = I * t to calculate the time required to pass this amount of charge at a current of 4.91 A:

t = Q / I = 25452 / 4.91 = 5189 s = 1.44 hours

Therefore, the current of 4.91 A would need to be applied for 1.44 hours to plate out 8.40 g of copper.

It's worth noting that this calculation assumes 100% efficiency in the electroplating process, which is often not the case in practice. Factors such as the purity of the solution, the temperature, and the electrode surface area can all affect the efficiency of the electroplating process and should be taken into account in real-world applications.

Learn more about electroplating

brainly.com/question/20112817

#SPJ11

The magnetic flux through the shaded face is 0.00816 Wb, and the total flux through the six faces is 0.04896 Wb.

The magnetic flux can be calculated through the shaded face of the cube, we need to use the formula:

Φ = B ⋅ A

where Φ is the magnetic flux, B is the magnetic field vector, and A is the area vector of the shaded face.

(a) To find the magnetic flux through the shaded face:

Given:

Edge length of the cube, ℓ = 4.00 cm = 0.04 m

Magnetic field vector, B = 5.1 î + 4.0 ĵ + 3.0 k T

The shaded face is parallel to the yz-plane, so the normal vector to this face is in the positive x-direction. Therefore, the area vector of the shaded face, A, is given by A = ℓ² î.

The magnitude of the area vector is |A| = ℓ² = (0.04 m)² = 0.0016 m²

Now, we can calculate the magnetic flux through the shaded face:

Φ = B ⋅ A

  = (5.1 î + 4.0 ĵ + 3.0 k) T ⋅ (0.0016 m² î)

  = 5.1 T × 0.0016 m²

  = 0.00816 Wb

Therefore, the magnetic flux through the shaded face is 0.00816 Weber (Wb).

(b) To find the total flux through the six faces of the cube, we need to consider that each face has the same magnitude of magnetic flux as the shaded face.

Since there are six faces in total, the total flux through the six faces is:

Total flux = 6 × Flux through the shaded face

                = 6 × 0.00816 Wb

                = 0.04896 Wb

Therefore, the total flux through the six faces of the cube is 0.04896 Weber (Wb).

Learn more about magnetic flux

brainly.com/question/31501008

#SPJ11

The change in entropy during the process of 1.0 kg of steam at 100°C condensing to water at 100°C is -2.44 kJ/K.

Entropy is a measure of the disorder or randomness of a system. The change in entropy during a process can be calculated using the formula ΔS = Q/T, where ΔS is the change in entropy, Q is the heat transferred during the process, and T is the temperature at which the heat is transferred.

In this case, 1.0 kg of steam at 100°C condenses to water at 100°C. During this process, the steam releases heat to the surroundings, which is absorbed by the water. The heat transferred during the process can be calculated using the formula Q = m × L, where Q is the heat transferred, m is the mass of the steam, and L is the latent heat of vaporization of water.

To know more about condensing visit:

https://brainly.com/question/956180

#SPJ11

Matching 1:

- Regions near the core of a galaxy that are abnormally bright in some wavelength: AGN

Matching 2:

- Galaxy formation and evolution seems to be a combination of which two processes?: Early cloud collapse and later galaxy mergers

Regarding the question about ruling out the idea of dark matter being massive, dark objects in the halo of galaxies, astronomers have used various methods to investigate and understand dark matter. One of the key reasons that dark matter is believed to be something other than massive, dark objects in the halo of galaxies is the observation of gravitational lensing. Gravitational lensing occurs when the gravitational field of a massive object bends and distorts light passing near it. By studying gravitational lensing in galaxies and galaxy clusters, astronomers have found evidence for the presence of dark matter, as the observed gravitational effects are much larger than what could be explained by visible matter alone. Additionally, other observations such as the rotation curves of galaxies and the distribution of matter in galaxy clusters also support the existence of dark matter as a distinct entity from ordinary matter.

Learn more about **dark matter** and the evidence supporting its existence here:

https://brainly.com/question/29545146?referrer=searchResults

#SPJ11

The focal length of the makeup mirror is 0.588 meters or approximately 58.8 centimeters.

To find the focal length of a makeup mirror that has a power of 1.70 D (diopters).

We can use the following formula:

f = 1/P

where f is the focal length in meters and P is the power in diopters.

Substituting P = 1.70 D into the formula, we get:

f = 1/1.70 D

f = 0.588 m

Therefore, the focal length of the makeup mirror is 0.588 meters or approximately 58.8 centimeters.

This means that light rays entering the mirror will converge at a distance of 0.588 meters behind the mirror's surface

Learn more about Focal length

brainly.com/question/13091382

#SPJ11

The position of a 0.30-kg object which is attached to a spring is described by x = (0.30 m) cos(0.8?t). Then, the amplitude of the motion is; 0.30 m, the spring constant is 0.192 N/m, the position of the object at t = 0.29 s is 0.260 m, and the object's speed is 0.070 m/s when t = 0.29 s .

The amplitude of the motion is the maximum displacement from equilibrium, which is equal to the coefficient in front of the cosine function. Therefore, the amplitude is 0.30 m.

The equation of motion for a mass attached to a spring is given by:

x = A cos(ωt)

where x is position of the mass, A is amplitude, ω is angular frequency, and t is time. The spring constant, k, is related to angular frequency by the equation;

ω = √(k/m)

where m is the mass of the object attached to the spring.

Rearranging this equation to solve for k, we get;

k = mω²

Plugging in the given values, we get;

k = (0.30 kg)(0.8 rad/s)² = 0.192 N/m

Therefore, the spring constant is 0.192 N/m.

To find the position of the object at t = 0.29 s, we plug in the given value of t into the equation for x;

x = (0.30 m) cos(0.8?t)

x = (0.30 m) cos(0.8 × 0.29 s)

x = 0.260 m

Therefore, the position of the object at t = 0.29 s is 0.260 m.

The velocity of the object is given by the derivative of the position function with respect to time;

v = dx/dt = -Aω sin(ωt)

At t = 0.29 s, we have;

v = -(0.30 m)(0.8 rad/s) sin(0.8 × 0.29 s)

v = -0.070 m/s

Therefore, the object's speed at t = 0.29 s is 0.070 m/s.

To know more about spring constant here

https://brainly.com/question/20785296

#SPJ4

1. To evaporate 20 g of water at 100 °C, you need 10,800 cal.

2. To heat 28 g of ice from -10 °C to liquid water at 28 °C, you need 2,548 cal.



1. To evaporate 20 g of water, multiply the mass (20 g) by the heat of vaporization (540 cal/g):
20 g × 540 cal/g = 10,800 cal

2. For the ice, there are three steps:
a) Heating ice from -10 °C to 0 °C:
28 g × 0.5 cal/g°C × 10 °C = 140 cal

b) Melting ice at 0 °C:
28 g × 80 cal/g = 2,240 cal

c) Heating liquid water from 0 °C to 28 °C:
28 g × 1 cal/g°C × 28 °C = 784 cal

Total heat required: 140 cal + 2,240 cal + 784 cal = 3,164 cal

To know more about heat of vaporization click on below link:

https://brainly.com/question/13372553#

#SPJ11

a. The liquid flow rate in bed volumes per hour is 183.3 BV/hr, and the volume of liquid treated per unit mass of carbon (ℓ/kg) at an allowable breakthrough of 35 mg/ℓ toc is 11.1 ℓ/kg.

b. The kinetic constant k1 is 0.047 ℓ/s-kg, and the constant q0 is 0.093 kg/kg.

a. The liquid flow rate in bed volumes per hour can be calculated by dividing the liquid flow rate (17.42 ℓ/hr) by the bed volume (1.04 m × π × (0.095/2)²). This gives a flow rate of 183.3 BV/hr. The volume of liquid treated per unit mass of carbon can be calculated by dividing the liquid flow rate by the mass of carbon (2.98 kg), resulting in 11.1 ℓ/kg.

b. The kinetic constant k1 can be determined using the equation k1 = q0/C₀, where q0 is the breakthrough concentration (35 mg/ℓ toc) and C₀ is the initial concentration (0.679 ℓ/s-m² × 2.98 kg = 2.023 ℓ/kg). Thus, k1 = 0.047 ℓ/s-kg. The constant q0 can be calculated using the equation q0 = C₀ × k1, which yields 0.093 kg/kg.

These calculations provide important parameters for the pilot column breakthrough test, including the liquid flow rate, the volume of liquid treated per unit mass of carbon, the kinetic constant, and the breakthrough constant.

Learn more about carbon here:

https://brainly.com/question/13046593

#SPJ11

The time required to reach 2% of the original speed in the pool of water is 0.0067 s.

Given:

Speed, v = 5 m/s

Mass, 75 kg

Drag force, F = -1.1 × 10⁴ V

The drag force acting on an object in a fluid is given by the equation:

F = -bv

Here b is the drag coefficient and v is the velocity of the object.

From Newton's second law of motion:

F = ma

(-1.10 × 10⁴)V = m × a

a = (-1.10 × 10⁴ V) / m

Substituting the given values:

a = (-1.10 × 10⁴ × 5.0 m/s) / 75 kg

a = -733.33 m/s²

The time it takes to reach 2% of the original speed:

v = u + at

0.1 m/s = 5.0 m/s + (-733.33 m/s²)  t

-4.9 m/s = -733.33 m/s^2 × t

t = 0.0067 s

Hence, the time is 0.0067 s.

To learn more about time, here:

https://brainly.com/question/28238258

#SPJ12

At a typical rate of 1 centimeter per year, it would take approximately 350 million years for two continents located 3500 kilometers apart to collide.

At a rate of 1 centimeter per year, the motion of tectonic plates is relatively slow. If two continents are 3500 kilometers (3,500,000 meters) apart, it would require 350 million years for them to collide. This calculation is based on the assumption that the rate of plate motion remains constant over such a long period, which is not always the case in reality. The collision of continents is a complex process influenced by various factors, including plate boundaries, geological activity, and the presence of other landmasses. Nevertheless, the estimation provides a rough idea of the timescale involved in continental collision at this rate of plate motion.

Learn more about continents here:

https://brainly.com/question/34140

#SPJ11

When charging, conductors usually give off electrons. Conductors are materials that allow electrons to pass through them easily, whereas insulators are materials that prevent electrons from moving through them. Conductors can easily discharge when exposed to static electricity because electrons move more freely through conductors than they do through insulators.

When an object with an excess of electrons comes into touch with an object with a deficiency of electrons, the electrons will move from the charged object to the uncharged object because of the difference in potential energy. The most familiar conductors are metals, which are highly conductive due to the presence of free electrons. Insulators, on the other hand, are materials that do not conduct electricity. Air, paper, plastic, and rubber are all examples of insulators. The transfer of electrons from one object to another by friction, conduction, or induction is referred to as charging. When two materials are rubbed together, their electrons rub together, resulting in one material becoming charged positively and the other becoming charged negatively.

Learn more about potential energy here ;

https://brainly.com/question/24284560

#SPJ11

Shows that the total ground-state energy of N fermions in a three-dimensional box is proportional to the number of particles and the Fermi energy, and the average energy per fermion is proportional to the Fermi energy.

The total ground-state energy of N fermions in a three-dimensional box can be derived using the Fermi-Dirac statistics and the density of states in three dimensions.

The Fermi energy (E_F) is the energy of the highest occupied state at absolute zero temperature. In a three-dimensional box of volume V, the density of states (D) can be calculated as D=V/h^3, where h is the Planck constant.

Using the Fermi-Dirac distribution, the total number of particles (N) can be expressed as:

N = 2 * V * (2m/h^2)^3/2 * ∫[0 to E_F] (E-E_F)^(1/2) dE

where m is the mass of a single fermion.

Solving for E_F, we get:

E_F = h^2 / 2m * (3π^2 N / V)^(2/3)

The total ground-state energy (R_total) can be obtained by summing up the energies of all the occupied states up to E_F. This can be expressed as:

R_total = 2 * V * (2m/h^2)^3/2 * ∫[0 to E_F] E (E-E_F)^(1/2) dE

Simplifying this expression and substituting for E_F, we get:

R_total = (3/5) * N * E_F

Therefore, the average energy per fermion is given by:

(3/5) * E_F = (3/5) * h^2 / 2m * (3π^2 N / V)^(2/3)

This shows that the total ground-state energy of N fermions in a three-dimensional box is proportional to the number of particles and the Fermi energy, and the average energy per fermion is proportional to the Fermi energy.

Learn more about ground-state energy

brainly.com/question/2289096

#SPJ11

The wavelength of the blue light emitted by a mercury lamp with a frequency of[tex]6.88 × 10^14 s^-1[/tex] is 436.6 nm.

The wavelength of the blue light emitted by the mercury lamp can be calculated using the equation λ = c/ν, where λ is the wavelength, c is the speed of light ([tex]3.00 × 10^8 m/s[/tex]), and ν is the frequency of the light. First, the frequency of the light is converted to hertz by multiplying 6.88 × 10^14 s^-1 by 1 Hz/1 s, giving a frequency of [tex]6.88 × 10^14 Hz[/tex]. Then, the frequency is plugged into the equation,[tex]λ = 3.00 × 10^8 m/s ÷ 6.88 × 10^14 Hz[/tex], and the answer is converted from meters to nanometers by multiplying by [tex]10^9[/tex], resulting in a wavelength of 436.6 nm for the blue light emitted by the mercury lamp.

Learn more about wavelength here:

https://brainly.com/question/31143857

#SPJ11

With reference from the graph, the order in which the blocks are dropped onto the disk is shown a s: C, B, A.

A  graph can be described as as a pictorial representation or a diagram that represents data or values in an organized manner.

The graph is a graph of Angular speed of the disk vs time graph

From the graph,   the disk is initially spinning at a constant angular speed of ω0ω0.

Then, as blocks are deposited onto the disk, the graph displays three separate times where the angular speed changes.

The order in which the blocks are dropped onto the disk can be inferred from the graph: Block C is first dropped at location P1 on the disk and here  the angular speed of the disk begins to decrease.

Block B is then dropped onto the disk, at point P2 which  causes the angular speed of the disk to decrease much further.

Block A is dropped onto the disk last, at point P3 causing  the angular speed of the disk to decrease even further until it eventually reaches a constant value.

Learn more about angular speed at: https://brainly.com/question/25279049

#SPJ4

The potential difference between the center and the surface of the sphere is 1.08 × 10⁶ V.

The potential difference between the center and surface of the sphere with a uniform charge distribution can be expressed mathematically as:

V = kQ/R

Where V is the potential difference, k is Coulomb's constant (9 × 10⁹ Nm²/C²), Q is the charge, and R is the radius of the sphere.

For this specific problem, the potential difference can be calculated as:

V = (9 × 10⁹ Nm²/C²) × (+6.00 × [tex]10^-^6[/tex] C) / (0.06 m) = 1.08 × 10⁶ V.

Therefore, the potential difference between the center and surface of the sphere is 1.08 × 10⁶ V.

Learn more about Potential difference

brainly.com/question/12198573

#SPJ11

Gravitational forces are attractive and depend on the mass of the objects involved. This is supported by various lines of evidence, such as the observed behavior of celestial bodies, the laws of motion formulated by Isaac Newton, and the predictions and measurements made by Albert Einstein's theory of general relativity.

Gravitational forces being attractive and dependent on the mass of objects can be substantiated by several pieces of evidence. Firstly, the observed behavior of celestial bodies in the universe supports this notion. Planets orbit around stars, moons orbit around planets, and galaxies exhibit cohesive structures. These motions can be explained by the attractive nature of gravity, where massive objects exert a pull on other objects.

Secondly, the laws of motion formulated by Isaac Newton provide additional evidence. Newton's law of universal gravitation states that every particle attracts every other particle with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between their centers. This mathematical relationship implies an attractive force that is influenced by the mass of the objects involved.

Furthermore, Albert Einstein's theory of general relativity, which successfully explains gravity as the curvature of spacetime, also supports the idea of attractive gravitational forces. The theory predicts and has been validated by experiments that massive objects, such as the Sun, can bend the path of light, creating gravitational lensing effects. In conclusion, the existence of gravity as an attractive force dependent on the mass of objects is supported by various lines of evidence. The observed behavior of celestial bodies, the laws of motion formulated by Newton, and the predictions and measurements made by Einstein's theory of general relativity all contribute to the validity of this argument.

To learn more about Gravitational forces refer:

https://brainly.com/question/72250

#SPJ11

The circuits ranked in order of their resonance frequencies from largest to smallest are: B. LC series resonant circuit, A. LC parallel resonant circuit, C. RC parallel resonant circuit, and D. RC series resonant circuit.

The resonance frequency of an LC circuit is given by f = 1/(2π√(LC)), where L is the inductance and C is the capacitance of the circuit. For a given value of C, the resonance frequency increases with increasing inductance. Therefore, an LC series resonant circuit, which has a larger inductance than an LC parallel resonant circuit, will have a higher resonance frequency.

On the other hand, the resonance frequency of an RC circuit is given by f = 1/(2πRC), where R is the resistance and C is the capacitance of the circuit. For a given value of C, the resonance frequency decreases with increasing resistance. Therefore, an RC parallel resonant circuit, which has a smaller resistance than an RC series resonant circuit, will have a higher resonance frequency.

Thus, the order of the resonance frequencies from largest to smallest is B. LC series resonant circuit, A. LC parallel resonant circuit, C. RC parallel resonant circuit, and D. RC series resonant circuit.

To know more about resonance frequency refer here:

https://brainly.com/question/31823553#

#SPJ11

Complete Question:

Rank the following circuits on the basis of their resonance frequencies, from largest to smallest:

A. LC parallel resonant circuit

B. LC series resonant circuit

C. RC parallel resonant circuit

D. RC series resonant circuit

To rank items as equivalent, overlap them.

The buoyant force that suspends the blimp in the air can be calculated as follows; Formula used: Buoyant force = weight of displaced fluid. Buoyant force = Density of air x Volume of the blimp x Acceleration due to gravity. Buoyant force = 1.21 kg/m³ x 5450 m³ x 9.8 m/s.Buoyant force = 64462.6 N. Thus, the buoyant force that suspends the blimp in the air is 64462.6 N.

B) The weight of the blimp can be calculated using the formula: Formula used: Weight = Mass x Gravity.

Mass of blimp = Density of helium x Volume of a blimp.

Weight of blimp = 0.178 kg/m³ x 5450 m³ x 9.8 m/s², Weight of blimp = 93280.6 N.

The buoyant force is less than the blimp's weight as the buoyant force is 64462.6 N and the blimp's weight is 93280.6 N.

Thus, the buoyant force is less than the blimp's weight.

C) The amount of weight, in addition to the helium, that the blimp can carry and still continue to maintain a constant altitude can be calculated using the formula: Formula used: Buoyant force = (Density of fluid x V object submerged in the fluid) x g,

Buoyant force = (Density of fluid x (Volume of the blimp - Volume of helium)) x g,

The weight that can be carried = (Density of fluid x Volume of object) - (Density of object x Volume of the object)

The weight that can be carried = (Density of air x Volume of blimp) - (Density of helium x Volume of helium).

Weight that can be carried = (1.21 kg/m³ x 5450 m³) - (0.178 kg/m³ x 5450 m³).

The weight that can be carried = 6556.95 N.

Thus, the weight, in addition to the helium, that the blimp can carry and still continue to maintain a constant altitude is 6556.95 N.

Learn more about buoyant force here ;

https://brainly.com/question/20165763

#SPJ11

Carts collide, spring pops out, and decompresses for 0.10 s. Carts' velocities after collision could be -0.5 m/s and 1.5 m/s.

Two lab carts of the same mass with negligible mass wheels are free to move on a horizontal track.

Cart 1 moves to the right at 1.0 m/s and collides with cart 2, which is initially at rest.

Cart 2 has a compressed spring-loaded plunger with stored energy that pops out and stays in contact with cart 1 for 0.10 s as the spring decompresses.

No mechanical energy dissipates during the collision.

The possible velocities after the collision for cart 1 and cart 2 are -0.5 m/s and 1.5 m/s, respectively.

These velocities are determined by the conservation of momentum and the energy stored in the spring.

For more such questions on collide, click on:

https://brainly.com/question/7221794

#SPJ11

The velocities of the two carts after the collision could be 0.5 m/s to the right for Cart 1 and 0.5 m/s to the left for Cart 2, or -1.0 m/s to the left for Cart 1 and 2.0 m/s to the right for Cart 2.

To solve this problem, we can use conservation of momentum. Before the collision, the momentum of the system is the mass of Cart 1 times its velocity, since Cart 2 is initially at rest. During the collision, the spring-loaded plunger transfers some of its stored energy to the carts, causing a change in their velocities. After the collision, the momentum of the system is again the sum of the momenta of the two carts. Since there is no external force acting on the system, the total momentum before and after the collision must be equal.

Using the conservation of momentum, we can set up an equation that relates the velocities of the carts before and after the collision. We know that Cart 1 has a mass of m and an initial velocity of 1.0 m/s to the right, and that Cart 2 has a mass of m and an initial velocity of 0 m/s. Let v1f and v2f be the final velocities of Cart 1 and Cart 2, respectively. The conservation of momentum equation becomes:

(m)(1.0 m/s) + 0 = (m)(v1f) + (m)(v2f)

Simplifying this equation, we get:

v1f + v2f = 1.0 m/s

During the collision, the plunger stays in contact with Cart 1 for 0.10 s as the spring decompresses. Since the collision is elastic, we can use conservation of energy to relate the velocities of the carts before and after the collision. The kinetic energy before the collision is:

KE = (1/2)mv1^2

After the collision, the kinetic energy is:

KE = (1/2)mv1f^2 + (1/2)mv2f^2

Since the plunger transfers energy from the spring to the carts, the total kinetic energy after the collision is greater than the kinetic energy before the collision. We can relate the velocities using the equation:

(1/2)mv1^2 = (1/2)mv1f^2 + (1/2)mv2f^2

Simplifying this equation, we get:

v1^2 = v1f^2 + v2f^2

Substituting v1f + v2f = 1.0 m/s from the conservation of momentum equation, we get

v1^2 = v1f^2 + (1.0 m/s - v1f)^2

Simplifying this equation and solving for v1f, we get:

v1f = (1/2)(1.0 m/s + sqrt(3) m/s)

or

v1f = (1/2)(1.0 m/s - sqrt(3) m/s)

Using these values, we can calculate v2f using the conservation of momentum equation. We get:

v2f = 1.0 m/s - v1f or

v2f = -v1f

Therefore, the possible velocities for Cart 1 and Cart 2 after the collision are 0.5 m/s to the right for Cart 1 and 0.5 m/s to the left for Cart 2, or -1.0 m/s to the left for Cart 1 and 2.0 m/s to the right for Cart 2.

Learn more about conservation of momentum:

https://brainly.com/question/24989124

#SPJ11

The average power output of the laser during the 30.0 s feline play session is 3.74 x 10⁻³ W.

The average power output of the laser can be calculated using the formula:

Power = Energy/Time

where Energy is the total energy emitted by the laser during the play session, and Time is the duration of the play session.

The energy emitted by each photon of the laser can be calculated using the formula:

Energy = h*c/λ

where h is Planck's constant, c is the speed of light, and λ is the wavelength of the laser.

Substituting the given values, we get:

Energy per photon = (6.626 x 10⁻³⁴ J s) x (2.998 x 10⁸ m/s) / (655 x 10⁻⁹ m)

= 3.033 x 10⁻¹⁹ J

The total energy emitted by the laser during the 30.0 s play session can be calculated by multiplying the energy per photon by the number of photons emitted:

Total energy = Energy per photon x Number of photons emitted

= (3.033 x 10⁻¹⁹ J/photon) x (3.70 x 10¹⁷ photons)

= 1.122 x 10⁻¹ J

Finally, we can calculate the average power output of the laser during the play session:

Power = Energy/Time

= (1.122 x 10⁻¹ J) / (30.0 s)

= 3.74 x 10⁻³ W

Therefore, the average power output of the laser during the 30.0 s feline play session is 3.74 x 10⁻³ W.

Note: The power output of a laser is the rate at which it emits energy in the form of photons. The energy of each photon is determined by its frequency or wavelength. In this case, the laser emits photons with a wavelength of 655 nm, and the number of photons emitted is given. From this information, we can calculate the total energy emitted and then the power output.

To know more about power output, refer to the link below:

https://brainly.com/question/31961373#

#SPJ11

False. In a crystalline metal, the slip direction is the direction along which the dislocations move when deformation occurs.

It is not necessarily the direction with the shortest interatomic distance. The slip direction is determined by the crystal structure and the arrangement of atoms in the material. It is influenced by factors such as crystallographic planes and the arrangement of atoms within those planes. The slip direction is important for understanding the mechanical properties and deformation behavior of metals. In a crystalline metal, the atoms are arranged in a regular and repeating pattern called a crystal lattice. This organized arrangement gives the metal its characteristic structure and properties. The atoms are closely packed together in a three-dimensional arrangement, forming a crystal structure.

Learn more about crystalline metal here:

https://brainly.com/question/28395930

#SPJ11

The maximum axial force p that can be applied to the bar can be determined using the formula:

p = σallow * A

where A is the cross-sectional area of the bar.

Explanation: The formula above is derived from the stress-strain relationship for a material, which states that stress is equal to force divided by area. The allowable normal stress is the maximum stress that the material can withstand without undergoing plastic deformation. By multiplying this allowable stress with the cross-sectional area of the bar, we can determine the maximum axial force that can be applied without exceeding the material's strength.

Therefore, to determine the maximum axial force p that can be applied to the bar, we need to know its cross-sectional area. Once we have this information, we can use the formula p = σallow * A to calculate the maximum force.

To know more about force, visit;

https://brainly.com/question/12785175

#SPJ11

If tight scissors have an efficiency of 50 percent, half of your work is wasted due to mechanical losses or inefficiencies.

Efficiency is a measure of how effectively a device or system converts input energy into useful output energy. In this case, the efficiency of tight scissors being 50 percent means that only half of the input energy you apply to the scissors is converted into useful output energy, while the other half is lost due to various factors.

Mechanical losses or inefficiencies in scissors can occur for several reasons, including friction, imperfect cutting edges, and deformation of the materials. When you squeeze the handles of the scissors, the energy you apply is not entirely transferred to the cutting action. Some of the energy is dissipated as heat due to friction between the blades, pivot point, and other moving parts. Additionally, if the scissors have dulled or damaged edges, more energy is required to cut through materials, resulting in increased inefficiency.

The wasted energy that is not utilized for cutting is typically converted into heat or sound energy, which does not contribute to the desired output of the scissors.

Therefore, due to mechanical losses or inefficiencies in the scissors, half of the work you apply is wasted, resulting in a 50 percent efficiency. This means that only half of your effort is effectively utilized for cutting, while the other half is lost as non-useful energy.

To know more about mechanical losses, please click on:

https://brainly.com/question/31722909

#SPJ11