Explanation:
The 24v is a higher-revving motor, thus you'd probably want the 4:10. The 12v has better low-end grunt and wont spin as fast, so the 3.54 would work better. Bombing is easier with the computer trucks, and cheaper with the mechanical trucks.
24V are much louder than a 12V at the engine.
While the 12-valve is a little bit more reliably with the mechanical P7100 pump, tuning it requires modified parts of the injection pump. The 24-valve might not be as insanely reliable, but it's still very reliable and can easily be tuned with a handheld tuner.
Tech A says that the standard 12-volt car battery has 3 cells with 4.2 volts in each cell. Tech B says that the
standard 12-volt car battery has 4 cells with 3.3 volts each. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both Technician A and B
d. Neither Technician A nor B
Explanation:
They're both incorrect.
The standard car battery has 6 cells with 2.1 volts a piece.
An artist is creating a gigantic mobile using old cars. On one end of the mobile, a 2100 lb Plymoth is suspended 30 feet from the fulcrum. In order for the mobile to be balanced, where should the artist suspend a 1400 lb Volkswagon?
a
20 feet from the fulcrum
b
7 feet from the fulcrum
c
45 feet from the fulcrum
d
on the fulcrum
Answer:
c 45 feet from the fulcrum
Explanation:
The moment at the fulcrum must be the same for each car. If the distance is d, then the artist must have ...
(2100 lb)(30 ft) = (1400 lb)(d)
2100·30/1400 ft = d = 45 ft
The Volkswagen should be 45 ft from the fulcrum.
Answer:
C. 45 feet from the fulcrumThat artist should suspend a 1400 lb/pounds Volkswagen.Technician A says that the brake pedal should be depressed with as much force as possible during the normal bleeding procedure. Technician B says that the brake pedal should be pumped rapidly during this manual bleeding procedure to force the air down toward the bleeder valve(s). Which technician is correct
Answer:
The appropriate answer is "Neither technician A nor B".
Explanation:
Two consultants or engineers complete the course of treatment A particularly unique upconverter to complement this same master cylinder. The customary static temperature would be used whenever the steering system has always been bleeding would be: 30 psi Two technicians start debating the bleeding atmosphere from either the hydraulic system.Therefore this obvious response is the appropriate one.
how far away from the compressor unit should an air transformer be installed?
Answer:
During installation, the air transformer should be located at least 25 feet minimum from the compressor unit
Explanation:
An air transformer is used to remove the dirt, water and oil in the compressed air and to filter as well as to provide air regulation and are required in spray finishing tasks that calls for a regulated clean and dry supply of air
The air transformer measures the pressure of the regulated air and can also come with air outlets for air operated tools, blow guns, spray guns, as well as for other purposes
In order to operate efficiently, the air transformer are required to be installed at a minimum distance of 25 feet (7.6 m) from the compressor unit.
A cylinder power balance test is being performed on a vehicle with sequential port fuel injection. Two adjacent cylinders are under performing. Technician A says this could be caused by a restriction in the fuel injectors. Technician B says this could be caused by leaking secondary insulation. Who is correct
Answer:
Neither A nor B
Explanation:
A cylinder balance test is used to locate cylinders that are underperforming and leading to loss of power and unbalanced engine performance, by measuring the drop in RPM on each cylinder as compared to the other cylinders
The factors that result in under performing cylinders includes;
1) Problem with the ignition
2) Inadequate or restricted fuel delivery
3) Valve faults
4) Piston wear
Where adjacent cylinders are the cause for the lack of power, the likely causes includes;
1) Head gasket fault
2) Crack in the head
3) Crack in the block.
13. The members installed vertically over and under a window opening are called
studs.
a. Cripple
b. Valley
C. Ridge
Explanation:
Cripples are vertical framing members that support a sill or saddle.
They are installed at points where a common stud would have stood if not for the window opening.
Cripples provide support for the window and the sill it rests on.
1. You should
when working with power tools.
A)O Ensure that machine guards are in place
B)O Secure your work with a clamp or vise
C)O Keep your work area clean
D) G Alof the above
You should ensure that machine guards are in place when working with power tools. The correct option is A.
What are power tools?Power tools are those tools that are run by power or electricity. These tools are used when constructing something. These tools are drill machines, cutters, axe, welding machines, etc.
These tools ate used by professionals or used by proper care because they are harmful tools that can lead to accidents. So when using power tools, you should wear helmets, gloves, and goggles to avoid any accidents.
The machine guards are given with the machine, they should be properly installed and used. If not installed or used properly, they can cut or injure you.
Thus, the correct option is A. Ensure that machine guards are in place.
To learn more about power tools, refer to the link:
https://brainly.com/question/11101078
#SPJ2
Entering information on a device is called what?
A. input
B. output
C. programming
D. coding
Explanation:
I'm not an engineering expert, but if I had to guess, I'd say it's A: Input.
What differentiates an athletic trainer from a clinical exercise physiologist?
An athletic trainer must have clinical experience.
An athletic trainer must be certified to obtain clinical experience.
An athletic trainer is more likely to obtain a master’s degree.
An athletic trainer is more likely to work directly with physicians.
Answer:
It's number 3
Explanation:
An athletic trainer must have clinical experience.
Technician A says that the most commonly used combustion chamber types include hemispherical, and wedge. Technician B says that coolant and lubricating openings and passages are located throughout most cylinder heads. Which technician is correct
Answer:
Technician A and Technician B both are correct.
Explanation:
Technician A accurately notes that perhaps the forms of combustion process most widely used are hemispherical and cross.
Technician B also correctly notes that in several cylinder heads, cooling system and greases gaps and pathways are found.
Select the correct answer from each drop-down menu. Which pencil should Edward use? Edward is creating a new design for his latest assignment. He first uses a ____1____to create a rough sketch for the design. Once he is confident of the design he uses the____2_____, retracing the drawing and making it darker.
Options for 1:
5B
3B
3H
Options for 2:
3B
5H
3H
Answer:
Blank 1 = 3H
Blank 2 = 3B
Explanation:
I got the question right on the test
Which of the following is an acronym used in mechanical plans?
Explanation:
Engineering drawing abbreviations and symbols are used to communicate and detail the characteristics of an engineering drawing. There are many abbreviations common to the vocabulary of people who work with engineering drawings in the manufacture and inspection of parts and assemblies.
Some examples of these are:
BOT: Bottom
B.O.W.: Bottom of Wall
BP: Blue Print (or B/P)
BV: Butterfly Valve
CAD: Cadmium or Computer-Aided Drafting
CBORE: Counterbore
C.C.: Center to Center
C.D.: Construction Document
C.F.M.: Cubic Feet per Minute
CFS: Cubic Feet per Second
C.I.: Cast Iron
E.F.: Exhaust Fan
EQ: Equal, or Equally
E.W.: Each Way
Ext.: Exterior
FACP: Fire Alarm Control Panel
FAO: Finish All Over
please tell us about your biggest success solving any mechanical issue
Explanation:
My biggest success solving any mechanical issue is learning how to use a wheelchair and making it easier for my sibling to move around.
Since my sibling broke her legs permanently, I felt terrible and wanted to do something to help out. My hallways were very small, so I wanted to make it easier for her to get around. I asked my parents if we could take down an unneeded wall in the hall, and so we did.
I calculated a bunch of thingies, and soon, my sibling could get around the house with ease, which really made me feel a lot better.
the worst time you have had with a mechanical issue
Answer:
When I was taking my sat exam online and my phone battery died
It took my poor dad three attempts to successfully have his truck fixed at the shop before they actually fixed anything.
which of the following statements about cylinder placement are true?
The statements from the options that are true about cylinder placement are;
Store cylinders in an upright position.Fasten cylinders to a wall or column.secure cylinders with chains or steel bands. always move cylinders with the safety cap in place. store cylinders in a special room or cage.Where are cylinders found?They can be seen on an inline engine. The first cylinder is seen at the front of the engine, that is very close to the timing cover.
In the Layout of Cylinder, the user can change the values to set up the configuration linked to cylinders and a crank shaft.
Learn more about cylinder from
https://brainly.com/question/18440876
Marks
Q 16.
Which one of the following is not a
feature of Microsoft Access?
Answer:
A Data redundancy
099
B. Facilitates sharing
Dos
C. To assess the
099
D. Allows you to
Answer:
i think C
Explanation:
if not really sorry
Summarize the difference in hydraulic and pneumatic systems.
Answer:
The main difference between a pneumatic system and a hydraulic system lies in how the energy necessary to make these systems work is generated: thus, while in the pneumatic system this energy is generated through the compression of gases, in the hydraulic system the energy is obtained Through the insertion of pressurized fluids, such as water. Furthermore, hydraulic systems are closed circuits, where the water constantly circulates within the system; while in pneumatic systems the air that is compressed and used is constantly renewed.
A gasoline engine transforms
_____energy into
_____energy for doing useful work.
Answer:
A gasoline engine transforms approximately 34% of the fuel's chamical energy into mechanical energy.
Explanation:
Many forms of combustion are examples of converting chemical energy into mechanical energy. Chemical energy is locked in the bonds of any combustible material: Gasoline, kerosene, wood, black powder.
Shooting off fireworks, igniting that bottle rocket converts the fuel inside into an exhaust gas which propels the rocket. Pulling the starter cord on your lawn mower ignites the fuel, releasing the energy that drives your lawn mower.
Automobiles, trains, planes all have combustion engines. Jet planes burn fuel more like a rocket engine, using the force generated by directed explosive gases.
The more interesting of this basic conversion principle today is in trying to create the stored chemical energy from mechanical energy. In other words, converting mechanical energy into clean fuel. One of the easiest to see is the use of wind power to produce the mechanical energy to create a DC energy and using that DC energy produce hydrogen from water via the process of electrolysis:
The wind drives the mechanical device that essential rotates a conductor through a magnetic field creating the DC voltage used to separate the hydrogen and oxygen. That mechanical to chemical conversion produces a pure hydrogen which has much more combustion potential energy than an equivalent mass of gasoline.
How are the scientific method and the engineering method similar?
Explanation:
Scientists use the scientific method to make testable explanations and predictions about the world. A scientist asks a question and develops an experiment, or set of experiments, to answer that question. Engineers use the engineering design process to create solutions to problems.
DO you of you guys know about Any Anmial rights it is for a resercah project
Explanation:
Sure! I'll give you the definition to start off-
The right of animals to be free from exploitation, domination and abuse by humans. Free-living Animals & Their Environment; To live free, animals need a place to live. Wildlife Law Program; The Wildlife Law Program focuses on the defense of wildlife and their habitats throughout the world.
Here are some examples of companies for Animal Advocates for inspiration.
PETA – People for the Ethical Treatment of Animals
International Fund for Animal Welfare – IFAW
Cincinnati Zoo & Botanical Garden
Here are some of the basic rights of animals.
- No experiments on animals.
- No breeding and killing animals for food or clothes or medicine.
- No use of animals for hard labor.
- No selective breeding for any reason other than the benefit of the animal.
- No hunting.
- No zoos or use of animals in entertainment.
Help I will brainliest
Answer:
hacking?
Explanation:
jsd
Discuss where Danino says bacteria grow can grow in your body. Why is it more easily able to live there, as opposed to other areas of the body?
Answer:
Danino says bacteria can grow in tumors in your body. It is easier to live there because they see it as their safe haven. The bacteria is safe there unlike in other parts of your body the bacteria will get filtered out.
Explanation:
The main reason why it is more easily able to live in tumors, as opposed to other areas of the body is:
They can stay and reproduce there without being filtered out by the body.What is Bacteria?This refers to the unicellular organisms which live in the body of a living or non living thing.
With this in mind, we can see that Danino was of the opinion that bacteria finds their safe haven inside tumors in the body because they feel safe and cannot be easily removed.
Read more about bacteria here:
https://brainly.com/question/17817006
Which of the following explains the main reason to cut a piece of wood on the outside of the measurement mark?
O to make up for the error of the saw being used
O to account for human error
O to account for the kerf
O to make up for the expansion of the wood
Let me help you with your baggage.
If eating three-egg omelets causes weight-gain, budgie eggs are a good substitute.
The waitress was not amused when he ordered green eggs and ham.
Peanut butter and jelly caused the elderly lady to think about her past.
It's not often you find a soggy banana on the street.
his seven-layer cake only had six layers.
I love bacon, beer, birds, and baboons.
We should play with legos at camp.
She did her best to help him.
His son quipped that power bars were nothing more than adult candy bars.
They improved dramatically once the lead singer left.
If you like tuna and tomato sauce- try combining the two. It’s really not as bad as it sounds.
Separation anxiety is what happens when you can't find your phone.
She tilted her head back and let whip cream stream into her mouth while taking a bath.
We have a lot of rain in June.
The father died during childbirth.
He set out for a short walk, but now all he could see were mangroves and water were for miles.
David subscribes to the "stuff your tent into the bag" strategy over nicely folding it.
You have every right to be angry, but that doesn't give you the right to be mean.
He decided water-skiing on a frozen lake wasn’t a good idea.
Answer:
is this free points??????????????????????????????
Explanation:
why do computers use 1 and 0
I like ya cut g
Explanation:
bonK no Uhm
Answer:
Computers use binary - the digits 0 and 1 - to store data
Explanation:
Computers use binary - the digits 0 and 1 - to store data The circuits in a computer's processor are made up of billions of transistors . A transistor is a tiny switch that is activated by the electronic signals it receives. The digits 1 and 0 used in binary reflect the on and off states of a transistor.
Which of the following is not true about manufacturing employment in the U.S?
Select one:
a. The number of people employed in the sector has dropped in the last ten years.
b. The number of people employed in the sector has risen dramatically.
c. Manufacturing jobs today require higher skills than in the past.
d. There is a high demand for skilled manufacturing workers.
Explanation:
If I guessed, I'd say the answer is choice (a).
The change in skills required to perform new tasks in manufacturing, along with import competition and a decline in mobility, have contributed to the decline of employment rate for manufacturing since 2000
Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz
1. How is diesel fuel ignited in a warm diesel engine?
A. Glow plugs
B. Heat compression
C. Spark plugs
D. Distributor-less ignition system
2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
B. Common rail
C. Direct injection
D. Distributor injection
3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
B. High pressure common rail
C. Direct injection
D. Distributor injection
4. The three phases of diesel ignition include _______________________.
A. Glow plug ignition, fast burn, slow burn
B. Slow burn, fast burn, slow burn
C. Ignition delay, repaid combustion, controlled combustion
D. Glow plug ignition, ignition delay, controlled combustion
5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
A. Fuel filter
B. Fuel supply line
C. Fuel return line
D. Water-fuel separator
6. The diesel injection pump is usually driven by a _________________.
A. Gear off the camshaft
B. Belt off the crankshaft
C. Shaft drive off of the crankshaft
D. Chain drive off of the camshaft
7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
A. Distributor
B. Inline
C. High-pressure common rail
D. Rotary
8. Glow plugs should have high resistance when _____________and lower resistance when __________________.
A. Cold/warm
B. Warm/cold
C. Wet/dry
D. Dry/wet
9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technicians A NOR B
10. What part should be removed to test cylinder compression on a diesel engine?
A. An injector
B. An intake valve rocker arm and stud
C. An exhaust valve
D. A glow plug
Answer: See explanation
Explanation:
1. How is diesel fuel ignited in a warm diesel engine?
B. Heat compression
2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
4. The three phases of diesel ignition include:
C. Ignition delay, repaid combustion, controlled combustion.
5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
D. Water-fuel separator
6. The diesel injection pump is usually driven by a _________________.
A. Gear off the camshaft
7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
C. High-pressure common rail
8. Glow plugs should have high resistance when _____________and lower resistance when __________________.
B. Warm/cold
9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
D. Neither Technicians A NOR B
10. What part should be removed to test cylinder compression on a diesel engine?
D. A glow plug
What are the risks of biohacking? Do you think the risks of biohacking outweigh the advantages? Why or why not?
Explanation:
Despite its futuristic outlook and results biohacking remains a largely unsupervised, dangerous if not illegal movement. Though the research and results produced by biohackers is ground breaking, it also breaks several ethical codes on human experimentation and endangering live of several humans.
I agree with the fact that risks outweigh advantages, but you can do things like:
- 3D Printing Body Parts
- Finding Cures
- Correcting Deformites.
The only issue is that it's illegal, unfortunately.
A disc brake rotor is being machined. Technician A says that a feed rate of 0.0008 inch per revolution and 150 RPM is where the rotor should be set for a final cut. Technician B says that the rotor should be given a non-directional surface finish using 150 grit sandpaper. Which technician is correct?
Answer:
Technician B only
Explanation:
During rotor reconditioning, which is the process also known as machining and sanding, where sanding is the involves the application of between 120 and 150 grit sandpaper while using a non-excessive force that is applied non-directionally for up to 60 seconds on each side such that the surface roughness meets OE standards. The rotors are then cleaned by washing after they are serviced before they can then be installed.
Three-dimensional measuring references all of these EXCEPT:
radius.
length.
width.
height.
Answer:
Radius. It is only used for Spheres
Explanation: