by how much should lower the pressure at the top of the straw to have the lemonade rise 5 cm above the surface

a. The angular acceleration of the engine is -1320 rad/s².

b. The engine makes approximately 118.7 revolutions during the deceleration.

Given:

Initial angular velocity (ω1) = 4500 rpm

Final angular velocity (ω2) = 1200 rpm

Time is taken (t) = 2.5 s

a) The formula for angular acceleration is:

α = (ω2 - ω1) / t

Substituting the given values, we get:

α = (1200 rpm - 4500 rpm) / 2.5 s = -1320 rad/s² (negative sign indicates a deceleration)

Therefore, the angular acceleration of the engine is -1320 rad/s².

b) To find the total number of revolutions, we need to convert the initial and final angular velocities from rpm to rad/s:

ω1 = 4500 rpm × 2π/60 = 471 rad/s

ω2 = 1200 rpm × 2π/60 = 126 rad/s

The average angular velocity (ω_avg) during the deceleration is given by:

ω_avg = (ω1 + ω2) / 2 = (471 rad/s + 126 rad/s) / 2 = 298.5 rad/s

The total angular displacement (θ) of the engine during the deceleration is given by:

θ = ω_avg × t = 298.5 rad/s × 2.5 s = 746.25 rad

Finally, the total number of revolutions (N) made by the engine is:

N = θ / 2π = 746.25 rad / 2π rad/rev = 118.7 rev (approximately)

Therefore, the engine makes approximately 118.7 revolutions during the deceleration.

learn more about angular acceleration here

https://brainly.com/question/21278452

#SPJ1

Answer:

Explanation:

Let's first convert the speeds of the trains from km/hr to m/s:

Train A: 24 km/hr = (24 x 1000) / (60 x 60) = 6.67 m/s

Train B: 48 km/hr = (48 x 1000) / (60 x 60) = 13.33 m/s

Now, let's find the distance covered by train A until it reaches its constant speed:

v = u + at

where

u = initial velocity = 0

a = acceleration = 1/6 m/s^2

t = time taken to reach constant speed

At constant speed, v = 6.67 m/s

So, 6.67 = (1/6)t + 0

t = 40 seconds

Using the formula for distance covered during uniform acceleration:

s = ut + (1/2)at^2

The distance covered by train A during the acceleration phase is:

s = (1/2)(1/6)(40^2) = 133.33 m

Now, let's find the equation of motion for train B:

s = ut + (1/2)at^2

where

u = initial velocity = 0

a = acceleration = 1/3 m/s^2

t = time taken to overtake train A

At the time of overtaking, both trains will cover the same distance. Let's call this distance "d". So we have:

d = 133.33 + 6.67t (distance covered by train A + distance covered by train B)

Setting the equations for both trains equal to each other, we get:

133.33 + 6.67t = (1/2)(1/3)t^2 + (1/3)t^2

Simplifying and solving for t, we get:

t = 180 seconds

Therefore, train B will overtake train A after 180 seconds or 3 minutes.

a. Here is a diagram of the situation:

                Q (-40 pC)

       |

       |

       |    (0,3)

       |

------ o-------- x-axis

       |

       |

       |    (0,0)

       |

     q (50 pC)

(b) The net electric flux through the closed cylindrical surface is -5.69×10⁵ Nm²/C.

To calculate this, we use Gauss's Law, which states that the net electric flux through any closed surface is proportional to the net charge enclosed by the surface. Mathematically, this is expressed as:

flux = E * A = (q_enclosed / ε0) * A

where E is the electric field, A is the area of the closed surface, q_enclosed is the net charge enclosed by the surface, and ε0 is the permittivity of free space.

In this case, we have a cylindrical surface with a height of 4 m and a diameter of 5 mA (which means a radius of 2.5 mA). The cylinder is centered at the origin and has the z-axis as its axis of symmetry. To apply Gauss's Law, we need to find the net charge enclosed by the cylinder.

Both charges q and Q are on the x-y plane, so they do not contribute to the net charge enclosed by the cylindrical surface. Therefore, the net charge enclosed by the surface is simply the sum of q and Q:

q_enclosed = q + Q = (50 pC) + (-40 pC) = 10 pC

Substituting this into Gauss's Law, we get:

flux = (q_enclosed / ε0) * A = (10 pC / 8.85×10⁻¹² F/m) * π (2.5×10⁻³ m)² (4 m) = -5.69×10⁵ Nm²/C

Therefore, the net electric flux through the closed cylindrical surface is -5.69×10⁵ Nm²/C.

What is an electric flux?

Electric flux is the measure of the number of electric field lines passing through a given surface. It is a scalar quantity and represents the amount of electric field passing through a surface per unit area. The SI unit of electric flux is volt-meter (V m) or newton-meter squared per coulomb (N m2/C).

To know more about electrical flux, visit:

https://brainly.com/question/14544020

#SPJ1

"Mars may once have met the requirements for livability, such as having liquid ocean, but at the moment, it top orbit is too thin so it lacks the huge magnetic field needed to support life as we know it.

having great aptitude or power to attract. a magnetic personality; of or pertaining to the a magnet or even to magnetism; of, pertaining to, and characterized by earth's magnetism; magnetized or able to be magnetized.

Yet, some substances have a high magnetic field, meaning that the majority of its electrons spin opposite direction. The strongest magnets are made of these materials because of their great magnetic permeability. They include the elements nickel, cobalt, and iron. The most potent type of magnet is one made of neodymium iron boron (NdFeb).

To know more about magnetic visit:

https://brainly.com/question/2841288

#SPJ1

The magnitude of power needed to keep the car traveling at a constant speed of 80 km/h would be  7 × [tex]10^4[/tex] watts.

The initial speed of the car is 95 km/h = 26.39 m/s, and the final speed is 65 km/h = 18.06 m/s. The change in speed over the 7.0 s interval is:

Δv = vf - vi = 18.06 m/s - 26.39 m/s = -8.33 m/s

The acceleration of the car can be found using:

a = Δv/t = -8.33 m/s / 7.0 s = -1.19 m/s^2

This is the deceleration of the car when it's in neutral. The force of friction acting on the car is:

F = ma = (1400 kg)(1.19 m/s^2) = 1666 N

To keep the car traveling at a constant 80 km/h = 22.22 m/s, a force equal in magnitude but opposite in direction to the force of friction must be applied. The power required to maintain this speed is:

P = Fv = (1666 N)(22.22 m/s) = 37000 W ≈ 3.7 × [tex]10^4[/tex] W

Therefore, the power needed to keep the car traveling at a constant 80 km/h is approximately 7 × [tex]10^4[/tex] watts.

More on power can be found here: https://brainly.com/question/30817666

#SPJ1

The subtle gradation of light and shadow to create the effect of three-dimensionality is described as shading.

In the context of art, shading refers to the use of light and shadow to render a three-dimensional object or scene realistically.

When an object is illuminated, light falls on its surface in different ways, depending on the position of the light source, the object's orientation, and the object's shape.

In this way, shadows are formed on the object's surface, and some regions receive more or less light than others.

By accurately depicting these light and shadow areas, artists can create an illusion of depth and dimensionality in their works.

for such more question on dimensiona

https://brainly.com/question/446697

#SPJ11

Answer:

Explanation:

A. To find Sam's top speed, we need to calculate the net force acting on him and use it to calculate his acceleration. Since he is moving at a constant speed, we know that his acceleration is zero. Therefore, the net force on him must be zero. The forces acting on Sam are the force of thrust from the skis and the force of friction between the skis and the snow.

The force of thrust is 220 N. The force of friction is given by:

friction = coefficient of friction × normal force

The normal force is equal to Sam's weight, which is given by:

weight = mass × gravity = 78 kg × 9.8 m/s^2 = 764.4 N

Therefore, the force of friction is:

friction = 0.1 × 764.4 N = 76.44 N

The net force is:

net force = thrust - friction = 220 N - 76.44 N = 143.56 N

Using Newton's second law, we can find Sam's acceleration:

net force = mass × acceleration

143.56 N = 78 kg × acceleration

acceleration = 1.838 m/s^2

Sam's top speed can be found using the kinematic equation:

v^2 = v0^2 + 2aΔx

where v0 is Sam's initial speed (which is zero), a is his acceleration, and Δx is the distance he travels before he runs out of fuel. Rearranging this equation, we get:

v = sqrt(2aΔx)

Plugging in the values, we get:

v = sqrt(2 × 1.838 m/s^2 × 14 s) = 7.96 m/s

Therefore, Sam's top speed is 7.96 m/s.

B. To find how far Sam travels before he runs out of fuel, we can use the kinematic equation:

Δx = v0t + (1/2)at^2

where v0 is Sam's initial speed (which is zero), a is his acceleration, and t is the time it takes for him to run out of fuel (which is 14 s). Plugging in the values, we get:

Δx = (1/2)at^2 = (1/2) × 1.838 m/s^2 × (14 s)^2 = 227.1 m

Therefore, Sam travels 227.1 meters before he coasts to a stop.

When you contact anything hot, the heat is transmitted from the object to your hand, making it feel hot. When you contact something cold, heat is transmitted from your hand to the object, making it feel chilly.

when heated, the molecules of the liquid in the thermometer move faster, causing them to get a little further apart. this results in movement up the thermometer. when cooled, the molecules of the liquid in the thermometer move slower, causing them to get a little closer together.

When the liquid in the thermometer is heated, the molecules move quicker, forcing them to move wider apart. This causes the thermometer to rise. When the liquid in the thermometer is chilled, the molecules travel slower, leading them to get closer together.

Learn more about heat

https://brainly.com/question/1429452

#SPJ1

The wavelength of the photon emitted by a hydrogen atom when an electron makes a transition from n = 2 to n = 1 state is 121.6 nm.

It is the most straightforward type of atom, with only one electron in its atomic shell. When an electron in a hydrogen atom moves from one energy level to another, it emits or absorbs a photon of light with a particular energy, E.

This energy difference can be found using the Rydberg formula for hydrogen atom wavelengths.

[tex]λ= 1/((Ry) × (1/ n1^2 - 1/ n2^2))[/tex]

where Ry = 1.097 x 107 m-1, and n1 and n2 are the initial and final quantum numbers of the electron, respectively.

In this instance, the electron goes from the n = 2 state to the n = 1 state.

The energy difference can be calculated as follows:

E = Rh (1/n2² - 1/n1²)

E = 2.18 × 10⁻¹⁸ J(1/12 - 1/22)

E = 1.63 × 10⁻¹⁸ J

The frequency of the photon emitted can be calculated

asv = E/hv = 1.63 × 10⁻¹⁸ J/6.63 × 10⁻³⁴

J.sv = 2.46 × 10¹⁴ Hz

Finally, we can use the formula c = λvc = λv

to find the wavelength of the photon emitted.

c/ v = λ121.6

nm = λ

Therefore, the wavelength of the photon emitted by a hydrogen atom when an electron makes a transition from n = 2 to n = 1 state is 121.6 nm.

for such more question on  wavelength

https://brainly.com/question/10728818

#SPJ11

Answer:

Explanation:

To calculate the torque exerted by the person on the diving board, we need to know the force exerted and the lever arm.

The force exerted by the person is the weight of their body, which can be calculated as:

F = mg

F = 65 kg x 9.81 m/s^2

F = 637.65 N

note: The acceleration of gravity "g" is therefore the result of gravitation (gravitational attraction) between the Earth and other celestial bodies, and of the centrifugal acceleration, due to the movement of the earth's rotation and its average global value is 9.81 ms -2.

The lever arm is the distance from the person to the pivot point, which is given as 1.5 m.

The torque (τ) can then be calculated as:

τ = F x d

τ = 637.65 N x 1.5 m

τ = 956.47 Nm

Therefore, the torque exerted by the person on the diving board with respect to the pivot point is 956.47 Nm.

The torque exerted by a force F at a distance r from the pivot point is given by the formula:

τ = F x r x sin(θ)

where θ is the angle between the force vector and the vector from the pivot point to the point where the force is applied.

In this case, the person's weight is the force being exerted on the board, and its magnitude is:

F = m x g = 65 kg x 9.8 m/s^2 = 637 N

The distance from the pivot point to the person is r = 1.5 m. Since the person is standing vertically, the angle between the weight vector and the vector from the pivot point to the person is 90 degrees, so sin(θ) = 1. Substituting the values into the torque formula, we get:

τ = 637 N x 1.5 m x 1 = 955.5 Nm

Therefore, the person is exerting a torque of 955.5 Nm on the diving board with respect to the pivot point.

The spring constant of the slingshot is 30 N/m. The spring constant is a measure of how much force is required to produce a certain amount of deformation in the spring.

What is Spring Constant?

Spring constant is a physical property that describes the stiffness of a spring or any elastic object. It is represented by the letter k and is defined as the force required to stretch or compress a spring by a given amount (x), divided by that amount:

k = F / x

where F is the applied force and x is the resulting displacement.

To determine the spring constant of the slingshot from the graph, we need to find the slope of the line that represents the force vs. displacement relationship.

The slope of a line is equal to the change in the vertical axis (y-axis) divided by the change in the horizontal axis (x-axis), or:

slope = Δy / Δx

In this case, the vertical axis represents the force (F) and the horizontal axis represents the displacement (x), so the slope of the line gives us the force per unit displacement, which is the spring constant (k).

From the graph, we can see that the force required to stretch the slingshot is directly proportional to the displacement, which means that the relationship between force and displacement is linear. Therefore, the slope of the line connecting the data points gives us the spring constant.

Using the two data points on the graph, we can calculate the slope as follows:

slope = (F2 - F1) / (x2 - x1)

= (3.5 N - 0.5 N) / (0.10 m - 0.00 m)

= 30 N/m

Therefore, the spring constant of the slingshot is 30 N/m.

Learn more about Spring Constant from given link

https://brainly.com/question/28203351

#SPJ1

Imaging: How big is the Andromeda Galaxy? What are the prime surface features of Mars? Are the stars in the Orion Nebula surrounded by gas?

Spectroscopy: What is the chemical composition of Crab Nebula? Determine the temperature of Jupiter's atmosphere?

Timing: Does the star Mira vary in it's brightness?

Spectroscopy is known to be the study of the absorption and emission of light and other radiation by matter. It is related that these processes depend on the wavelength of the radiation. Recently, the definition has been extended to include the study of interactions between particles like electrons, protons and ions, and interactions with other particles as a function of collision energy.

Spectroscopy has been essential to the development of some of the most fundamental theories of physics, including quantum mechanics, special and general relativity, and quantum electrodynamics. Spectroscopy applied to high-energy collisions has become an important tool in advancing the scientific understanding not only of electromagnetic forces, but also of strong and weak nuclear forces.

To know more about  Spectroscopy, visit:

https://brainly.com/question/5402430

#SPJ1

Note that the statement are identified as true or false below.

The true versions of the false statements:

Learn more aobut Waves:
https://brainly.com/question/29334933
#SPJ1

The value of f is 905/4 feet, After 4 seconds the ball reaches the ground and the velocity of the ball hit the ground is -10 - 4sqrt(905) ft/s

step 1:

When the ball reaches the maximum height, it means that the velocity is zero, we use this fact to calculate the value of "f".

The height of the ball is described by the function A is

[tex]h(t) = -16t² + 20t + 220[/tex]

When the ball reaches the maximum height, its velocity is zero, therefore:

[tex]v = dh/dt = 0[/tex]

We take the derivative of the height function to get the velocity function:

[tex]v(t) = -32t + 20[/tex]

When the velocity is zero, the ball has reached its maximum height:

[tex]-32t + 20 = 0[/tex] => t = 5/8 seconds

Step 2:

Now we calculate the maximum height by plugging in t = 5/8 seconds into the height function:\

[tex]h(5/8) = -16(5/8)² + 20(5/8) + 220[/tex]

= 905/4 feet

Step 3:

To determine when the ball reaches the ground, we need to find the time when the ball reaches a height of 0:

[tex]0 = -16t² + 20t + 220= > 2t² - 5t - 55 = 0[/tex]

Using the quadratic formula:

[tex]t = [5 ± sqrt(5² - 4(2)(-55))] / [2(2)]= (5 ± sqrt(905)) / 4[/tex]

We take the positive root since time cannot be negative:

t =  4 seconds

Step 4:

To calculate the velocity at which the ball hits the ground,

we take the derivative of the height function and evaluate it at the time when the ball hits the ground:

[tex]v(t) = -32t + 20= > v((5 + sqrt(905)) / 4)[/tex]

= -32((5 + sqrt(905)) / 4) + 20

= -10 - 4sqrt(905) ft/s

For more such questions on velocity , Visit:

https://brainly.com/question/24445340

#SPJ11

There are multiple questions in your prompt, so let's break them down one by one.

How much gravitational potential energy does the goat gain?

The gravitational potential energy gained by the goat can be calculated using the formula:

GPE = mgh

where m is the mass of the goat, g is the acceleration due to gravity (9.8 m/s^2), and h is the height of the cliff.

Substituting the given values, we get:

GPE = 50 kg x 9.8 m/s^2 x 450 m

GPE = 220500 J

Therefore, the goat gains 220500 J of gravitational potential energy.

How much gravitational potential energy does Evan gain?

The gravitational potential energy gained by Evan can be calculated using the same formula as above:

GPE = mgh

where m is the mass of Evan (including his parachute gear), g is the acceleration due to gravity, and h is the height of the jump.

Substituting the given values, we get:

GPE = 90 kg x 9.8 m/s^2 x 2.0 m

GPE = 1764 J

Therefore, Evan gains 1764 J of gravitational potential energy.

How much kinetic energy does the goat have just before it hits the ground?

The conservation of energy principle tells us that the total energy of the system (in this case, the goat) remains constant. So, the kinetic energy gained by the goat just before it hits the ground is equal to the gravitational potential energy it had at the top of the cliff. Therefore, the kinetic energy of the goat just before it hits the ground is:

KE = GPE = 220500 J

Note that we have assumed that there is no loss of energy due to air resistance or other factors during the goat's fall.

How much GPE does Evan gain given: h = 2.0 m

We have already calculated the gravitational potential energy gained by Evan earlier. Using the same formula, we get:

GPE = mgh

GPE = 90 kg x 9.8 m/s^2 x 2.0 m

GPE = 1764 J

What is the kinetic energy of the aircraft at a height of 5000.00 m?

We cannot calculate the kinetic energy of the aircraft with the given information. The kinetic energy of an object depends on its mass and velocity, but we only have information about its height. If we assume that the aircraft is stationary at a height of 5000.00 m, then its kinetic energy would be zero.

To know more about mass visit :-

https://brainly.com/question/86444

#SPJ1

Resistance of wire does not depend on current supplied, area of cross-section of the wire, length of the wire, or material of the wire.

The resistance of a wire does not depend on the current supplied. The resistance of a wire is determined by the following factors:

Length of the wire: The longer the wire, the more resistance it will have. This is due to the fact that a longer wire has more atoms that obstruct the flow of electrons. The more time the electrons take to traverse the wire, the more collisions they will have, resulting in more resistance.

Area of cross-section of the wire: The cross-sectional area of a wire is inversely related to its resistance. This implies that if the cross-sectional area is reduced, the resistance will rise. This is due to the fact that a smaller cross-sectional area leads to more electron collisions with atoms.

Material of the wire: The resistivity of the wire's material determines its resistance. A material with a higher resistivity would have more resistance than one with a lower resistivity. It's important to note that the resistivity of a material varies with temperature. As the temperature rises, so does the resistivity of the substance.

For more such questions on Resistance , Visit:

https://brainly.com/question/30901006

#SPJ11

Explanation:

a) looks correct  EXCEPT   KE and GPE labels are reversed ( if the one on the L is initially and the R one is at max height)

b) looks good

c)  incorrect       total energy will be KE + GPE =   57.51 J at any point

d) correct

Clock a remains in place and clock b is carried around the earth (40,000 km). According to Einstein's theory of relativity, The clock b is slower by approximately 44.6 seconds.

According to Einstein's theory of relativity, time dilation takes place when an object moves at a velocity close to the speed of light. The closer the velocity is to the speed of light, the more time slows down. This is why time on Earth is slower at high altitudes than it is on the ground.

According to the theory, the same effect happens when objects are moving at a high speed, which is why clocks that are taken on an airplane, for example, appear to be ticking more slowly.

1. The following equation is used to determine the time dilation:

t = t0 / √(1 – v²/c²),

where t is the time elapsed, t0 is the time at rest, v is the velocity, and c is the speed of light. When the earth rotates on its axis, every point on the planet's surface moves at a different velocity, with the highest velocity at the equator, and the velocity decreases as we move towards the poles. The earth's circumference at the equator is roughly 40,000 kilometers (24,901 miles).
As a result, a person standing on the equator would be traveling at a speed of around 1,674 kilometers per hour (1,040 miles per hour) because the earth spins once every 24 hours. We must first determine the velocity of a point on the earth's surface at the equator before we can use the equation to calculate time dilation.

2. We use the formula

v = 2πr / T,

where v is velocity, r is the radius of the earth, and T is the time it takes the earth to complete one rotation. The formula is as follows:

v = 2πr / Tv

= 2 x 3.14 x 6,378 km / 24 hv

= 1,674 km/h

3. Substituting these values into the equation, we get:

t = t0 / √(1 – v²/c²)t = t0 / √(1 – (1,674 m/s)² / (299,792,458 m/s)²)t = t0 / √(1 – 2.8 x 10^-8)t = t0 / 0.9999999714

This means that the clock on the equator will tick slightly slower than it would at rest. The difference in time can be calculated by subtracting the two values:

t – t0 = t0 / 0.9999999714 – t0t – t0 = t0 (1 – 0.9999999714)t – t0 = 0.0000000286 t0

4. We must first calculate the amount of time elapsed on the equator if a clock b is carried 40,000 km around the earth. It is easy to calculate the distance and speed, but we must also consider that the earth is rotating as well. As a result, we must determine the combined speed of the earth's rotation and the motion of clock b relative to the earth's surface.

5. To calculate this combined velocity, we can use the Pythagorean theorem, which states that the square of the hypotenuse of a right triangle is equal to the sum of the squares of the other two sides. If we imagine the velocity of the earth's rotation as the base of the triangle and the velocity of clock b as the height of the triangle, we can use this theorem to calculate the combined velocity as follows:

combined velocity = √(1,674² + vclock²)

where v clock is the velocity of clock b. Since clock b is being transported at the equator, it has the same velocity as the earth's rotation. As a result, we can substitute 1,674 km/h for v clock:

combined velocity = √(1,674² + 1,674²)

combined velocity = √(2 x 1,674²)

combined velocity = 2,367 km/h

6. Substituting the combined velocity into the equation for time dilation, we obtain:

t – t0 = t0 (1 – √(1 – v²/c²))t – t0 = t0 (1 – √(1 – (2,367 km/h)² / (299,792,458 m/s)²))t – t0

= t0 (1 – √(1 – 1.579 x 10^-11))t – t0

= t0 (1 – 0.999999999920215)t – t0

= 0.000000000079785 t0

Converting this value to seconds, we get:

0.000000000079785 t0 = 79.785 ns

Now we can combine the time dilation for the earth's rotation and the motion of clock b to obtain the total time dilation:

t – t0 = 0.0000000286 t0 + 0.000000000079785 t0t – t0 = 0.000000028679785 t0

Substituting the value of t0 (one second) into the equation, we get:

t – 1 = 0.000000028679785 seconds

Therefore, clock b will be approximately 44.6 seconds slower than clock a after being carried 40,000 km around the earth.

For more such questions on Einstein's theory of relativity , Visit:

https://brainly.com/question/3489672

#SPJ11

The frequency and period of a vibrating mass on a spring are affected by the mass of the object, the spring constant, and the amplitude of the vibration. The frequency is the number of complete back-and-forth vibrations per second, while the period is the amount of time it takes for one complete vibration.

The mass of the object affects the frequency and period because it affects the amount of force exerted on the spring. A larger mass will require more force to be exerted on the spring to produce the same amount of displacement as a smaller mass. This means the frequency and period will increase as the mass increases.

The spring constant affects the frequency and period because it determines how stiff the spring is. A stiffer spring requires more force to produce the same amount of displacement as a looser spring. Therefore, the frequency and period will increase as the spring constant increases.

The amplitude of the vibration affects the frequency and period because it determines how much the mass will be displaced from its equilibrium position. A larger amplitude will require more force to produce the same amount of displacement as a smaller amplitude, meaning the frequency and period will increase as the amplitude increases.

for such more question on  frequency

https://brainly.com/question/254161

#SPJ11

The Bohr radius is denoted by a and is equal to 0.529 Å.

The radius of the first Bohr orbit of hydrogen is then equal to a0 which is equal to 0.529 Å. The first Bohr orbit of hydrogen has an energy of -13.6 eV.

The energy of a stationary electron in the nth Bohr orbit of a hydrogen-like atom is given by-13.6 / n² eV

where n is the principal quantum number for the atom. The value of the principal quantum number for the atom is given by the formula

Ry / E = (n² / Z)

where Ry is the Rydberg constant, E is the ionization energy of the atom, and Z is the atomic number of the atom.

The radius of the nth Bohr orbit of a hydrogen-like atom is given bya / n²

where a is the Bohr radius. The Bohr radius is equal to 0.529 Å for hydrogen.

The radius of the first Bohr orbit of positronium is then given by

0.529 / 1²=0.529 Å

therefore, The radius of the first Bohr orbit of positronium is 0.529 Å.

for such more question on radius

https://brainly.com/question/30253926

#SPJ11

Electric field lines are a powerful tool to understand and visualize electric fields. They help to represent the direction and magnitude of the electric field at various points around a charged object.

The following statements are true about electric field lines:

A. Electric field lines cannot cross: This is because at the point where two field lines cross, there would be two directions for the electric field, which is impossible. Hence, the lines do not cross, and this is one of the fundamental characteristics of electric field lines.

B. Lines of electric field only originate from positive charges: Electric field lines originate from positive charges and terminate at negative charges. This is because positive charges repel positive charges and attract negative charges. Therefore, the electric field lines originating from a positive charge terminate at a negative charge.

C. Field lines point in the direction of the force the electric field creates on an electron: Electric field lines point in the direction of the force that would be experienced by a positive charge placed at any point in the field. Electrons, being negatively charged, would experience a force in the opposite direction to the electric field.

D. The strength of the electric field is greater in regions where the field lines are closer together: The density of field lines indicates the strength of the electric field. The closer the lines are, the stronger the field at that point.

E. In an electric-field-line drawing with many point charges, the number of field lines originating or terminating on each charge is proportional to the charge. That is, bigger charges have proportionally more field lines: The number of field lines originating or terminating on each charge is directly proportional to the magnitude of the charge.

F. The true strength of an electric field at any point can be determined from an electric field representation: The strength of the electric field at a point can be determined by the density of electric field lines at that point. However, the actual strength of the field would require quantitative measurements using instruments such as a voltmeter or an electrometer.

In conclusion, electric field lines are an essential tool in understanding the behavior of electric fields. They provide a visual representation of the electric field, its direction, and its strength at various points in space.

To know more about electric field visit :-

https://brainly.com/question/14372859

#SPJ1

If the same motor is to be driven from a 440-V, 60 Hz power supply, The slip at pullout torque is 0.0455.

The slip at pullout torque, pullout torque, and rotor speed at the pullout torque of the motor are given by Slip

[tex]s = Pmech/ (Xm\times 1.5\times V^2/1000)[/tex]

Pullout torque is given by [tex](0.5 \times V^2 / X2) \times (R2 / (R1^2 + (X1 + X2)^2))[/tex]

Rotor speed at pullout torque is given by Ns = (120f/p)(1 - s)

The given parameters of the motor are R1 = 0.075 Ohms, R2 = 0.065 Ohms, Xm = 7.2 Ohms, X1 = 0.17 Ohms, X2 = 0.17 Ohms, Pmech = 1.0 KW W, Pstray = 150 W, Pcore = 1.1 KW.

The motor is rated at 75 KW with a power factor of 0.85.Assuming the motor is running at unity power factor.

The output power of the motor is Pout = 75 KW and the input power to the motor is Pin = 75 KW / 0.85 = 88.24 KW

The input current to the motor is [tex]Iin = 88.24 KW / (3 \times 440 V \times sqrt(3)) = 89.5 A[/tex]

Therefore, the torque developed by the motor is [tex]T = 1000 \times Pout / (2 \times pi \times N)[/tex]

The slip at the pullout torque is given by [tex]s = sqrt((Pcore + Pstray) / Pout) = sqrt((1.1 KW + 150 W) / 75 KW) = 0.0455.[/tex]

The pullout torque is given by [tex](0.5 \times 440^2 / 0.17) \times (0.065 / (0.075^2 + (0.17 + 0.17)^2)) = 411.7 Nm.[/tex]

The rotor speed at pullout torque is [tex]Ns = (120 \times 50 / 2) \times (1 - 0.0455) = 2846 rpm.[/tex]

The pullout torque of the motor if driven from a 440 V, 60 Hz power supply is given by

[tex](0.5 \times 440^2 / 0.17) \times (0.065 / (0.075^2 + (0.17 + 0.17)^2)) \times (60 / 50) = 548.4 Nm.[/tex]

The slip at pullout torque is given by [tex]s = sqrt((1.1 KW + 150 W) / 75 KW) = 0.0455.[/tex]

for such more question on pullout torque

https://brainly.com/question/30167647

#SPJ11

Answer:

a) To find W, we can use the principle of moments. At balance, the sum of the clockwise moments about the fulcrum is equal to the sum of the counterclockwise moments about the fulcrum. Let the fulcrum be at a distance x from the left end of the rod.

Clockwise moment = (225 N)(2.00 m - x)

Counterclockwise moment = W(0.50 m) + (255 N - W)(1.50 m + x)

Setting these two moments equal, we have:

(225 N)(2.00 m - x) = W(0.50 m) + (255 N - W)(1.50 m + x)

Solving for W, we get:

W = 81.7 N

Therefore, the unknown weight W is 81.7 N.

b) If W is moved 25.0 cm to the right, its new position is 75.0 cm from the left end of the rod. To restore balance, we need to find the new position of the fulcrum. Again, we can use the principle of moments:

Clockwise moment = (225 N)(2.00 m - 0.75 m) + W(0.25 m)

Counterclockwise moment = (255 N - W)(1.50 m + 0.75 m - x)

Setting these two moments equal, we have:

(225 N)(2.00 m - 0.75 m) + W(0.25 m) = (255 N - W)(1.50 m + 0.75 m - x)

Substituting the value of W we found in part (a), we get:

(225 N)(2.00 m - 0.75 m) + (81.7 N)(0.25 m) = (255 N - 81.7 N)(1.50 m + 0.75 m - x)

Simplifying and solving for x, we get:

x = 1.32 m

Therefore, to restore balance, the fulcrum must be moved 0.57 m (1.32 m - 0.75 m) to the left.

A battleship simultaneously fires two shells in parabolic projectile motion and no information about initial speeds at enemy ships. The ship B got hit first. So, the correct choice for answer is option (c).

Here is we have a battleship Which fires two shells simultaneously at the enemy ship along the two paths. The initial speed of projection may be same or different. See the above figure carefully, the angle of projection for ship A is more than ship B. Time of flight for ship A is

[tex]T_A = \frac{ 2u_{A} sinθ_{A}}{g }[/tex]

For ship B, [tex]T_B = \frac{2u_B sinθ_{B}}{g }[/tex]

We have no idea about the initial speed of projection, so we cannot consider it for comparison. As we know from above,

[tex]θ_{A} > θ_{B}[/tex]

=> [tex]sinθ_{A} > sinθ_{B}[/tex]

So, [tex]T_{A} > T_{B}[/tex]

That is time of flight for ship A is greater than for the ship B. Therefore, ship B gets hit first.

For more information about projectile motion, visit :

https://brainly.com/question/28687429

#SPJ4

Complete question:

A battleship simultaneously fires two shells at enemy ships. if the shells follow the parabolic trajectories shown, which ship gets hit first?

a) A

b) both simultaneously

c) B

d) None

The age of the rock is approximately 2.58 billion years.

The half-life of uranium-238 is approximately 4.47 billion years. This means that after 4.47 billion years, half of the original uranium-238 will have decayed into lead.

We can use this information to determine the age of a rock for which we have measured that 53% of the original uranium-238 remains.

If 53% of the original uranium-238 remains, then 47% has decayed into lead.

Since half of the original uranium-238 decays every 4.47 billion years, the ratio of remaining uranium-238 to original uranium-238 after t years is given by:

[tex](remaining uranium-238) / (original uranium-238) = 0.53 = e^(-t/4.47E9)[/tex]

Solving for t, we get:

[tex]t = -4.47E9 * ln(0.53) = 2.58 billion years[/tex]

To know more about " uranium. here

https://brainly.com/question/14469933

#SPJ4

The average power developed by a diesel engine of a 400-Mg train increases the train's speed uniformly from rest to 10 m/s in 100 s along a horizontal track = 200 kW.

The first kinematic equation is v=v0+at , where v is the final velocity, v0 is the initial velocity, a is the constant acceleration, and t is the time

According to given information:

v = 10, v0= 0 , t= 100s, m=400

v=v0+at

10= 0+a(100)  

a= 0.1 m/s²

∑ F =ma  <==>  F= 400(10 ³ )(0.1) = 40(10 ³)N

Pavg = F. Vavg = 40(10 ³)(10/2) = 200 kW

It represents the typical quantity of work completed or energy converted per unit of time. When the context clearly indicates it, the average power is frequently referred to as "power".

The instantaneous power overrides the average power as time interval t gets closer to zero.

For more information on average power kindly visit to

https://brainly.com/question/17008088

#SPJ1

Answer:

You can use the same conversion factor to convert liters to gallons or you can use: 1 liter = 0.264 US gallons. To find how many gallons are in 4 liters, for example: gallons = 4 liters x 0.264 gallons/liter. The liters cancel out, leaving the gallon unit: 4 liters = 1.056 gallons. Keep this in mind: there are about 4 liters per US gallon.

Explanation:

Astronomers believe that the reason for the low levels of hydrogen and helium in the inner part of the Solar System is that these elements were lost due to the Sun's strong solar wind

. Most of the gas in the solar nebula was hydrogen and helium. However, there is very little hydrogen or helium in the inner part of the solar system today. Astronomers believe this is because the intense solar winds from the young Sun blew the lighter gases out into space.

The solar winds also blew away any smaller particles that had not yet stuck together to form larger objects, which is why there are very few small objects close to the Sun. This is why there is more hydrogen and helium in the outer part of the solar system.

Know more about  Astronomers here:

https://brainly.com/question/2141924

#SPJ11

Answer: 8.38 revolutions per second

Explanation:

Before the second disk is dropped, the initial angular momentum of the system is given by:

L = I1 * w1

where I1 is the moment of inertia of the first disk, and w1 is its angular velocity.

Substituting the given values, we have:

L = (25 kg m^2) * (2 rev/sec * 2π rad/rev) = 100π kg m^2/s

When the second disk is dropped onto the rotating disk, the total moment of inertia of the system will be the sum of the moment of inertia of the first disk and the moment of inertia of the second disk:

Itotal = I1 + I2/2

where I2/2 is the moment of inertia of the second disk, which is half as large as that of the first disk.

Substituting the given values, we have:

Itotal = (25 kg m^2) + (12.5 kg m^2) = 37.5 kg m^2

Conservation of angular momentum requires that the initial angular momentum of the system be equal to its final angular momentum, so:

L = Itotal * wf

where wf is the final angular velocity of the combined disk.

Solving for wf, we get:

wf = L / Itotal = (100π kg m^2/s) / (37.5 kg m^2) ≈ 8.38 rev/sec

Therefore, the new rotational speed of the combined rotating object is approximately 8.38 revolutions per second.