calculate the work done by gravity on the watermelon during its displacement from the roof to the ground

Answers

Answer 1

The work done by gravity on the watermelon during its displacement from the roof to the ground is 196 J.

The work done by gravity on the watermelon during its displacement from the roof to the ground can be calculated using the formula W = mgh, where W is the work done, m is the mass of the watermelon, g is the acceleration due to gravity and h is the height of the displacement.What is Work Done?Work done can be defined as the energy transferred when a force is applied to an object to move it over a certain distance. It is a scalar quantity and is measured in joules (J). The mass of the watermelon is not given in the question, so let us assume that the mass of the watermelon is 2 kg. The acceleration due to gravity, g is 9.8 m/s2, and the height of the displacement is not given in the question, so let us assume that the height of the displacement is 10 meters. Therefore, the work done by gravity on the watermelon during its displacement from the roof to the ground can be calculated as follows: W = mgh= (2 kg) (9.8 m/s2) (10 m)= 196J

Therefore, the work done by gravity on the watermelon during its displacement from the roof to the ground is 196 J.

Learn more about  work done  at brainly.com/question/13662169

#SPJ4


Related Questions

which event triggers the creation of an action potential?

Answers

The opening of voltage-gated sodium channels triggers the creation of an action potential.

An action potential is a brief electrical signal that travels down the axon of a neuron. This signal is triggered by the opening of voltage-gated sodium channels in response to a stimulus, such as a chemical neurotransmitter binding to a receptor on the neuron's membrane. The influx of positively charged sodium ions depolarizes the membrane, creating an electrical signal that rapidly spreads down the axon. Once the signal reaches the end of the axon, it triggers the release of neurotransmitters, which can then bind to receptors on other neurons and continue the transmission of the signal.

To know more about action potential, here

brainly.com/question/8312195

#SPJ4

a ford ranger has a mass of 2835 kg is traveling at a velocity of 55 mph down a mountain road in colorado. what distance in feet will it travel if the ramp had a 25% inclinvce

Answers

The distance in feet the Ford Ranger will travel can be calculated using the formula is 5,939.66 ft.


What is the distance in feet?

Distance (ft) = Velocity (mph) × Time (s) × 0.6818

In this case, Velocity = 55 mph, Time = Unknown.

Using the incline, we can calculate the time it takes the Ford Ranger to travel the given distance:

Time = Distance/[Velocity × (1 + Incline/100)]

Distance = 2835 kg × 9.81 m/s2 × 25% = 7101.75

time = 7101.75/[55 × (1 + 25/100)] = 129.44 seconds

distance (ft) = 55 × 129.44 × 0.6818 = 5,939.66 ft


To find the distance a Ford Ranger with a mass of 2835 kg will travel if the ramp had a 25% incline while traveling at a velocity of 55 mph down a mountain road in Colorado, the following formula will be applied: distance = [velocity² / (2 × acceleration)] × sin(2×angle of incline)

Let's find the acceleration using the formula:

a = (v² - u²) / 2s

where, a = acceleration = final velocity, u = initial velocity = distance

Therefore, a = (55² - 0²) / 2 × s = 166.25 / s... equation [1]

Now, let's find the sine of the angle of incline sin25° = 0.4226

Therefore, the distance the Ford Ranger will travel on a ramp with a 25% incline while traveling at a velocity of 55 mph down a mountain road in Colorado is given by; distance = [55² / (2 × (166.25 / s))] × sin(2 × 25°)

distance = 5,939.66 ft.

Read more about distance here:

https://brainly.com/question/26550516

#SPJ11

Which of these stars has the greatest surface temperature? a.... Which of these stars has the greatest surface temperature? a. a main-sequence B star b. a supergiant A star c. a giant K star

Answers

A main-sequence B star has the greatest surface temperature among the given options. B-type stars are hotter and more massive than A-type stars, which are in turn hotter and more massive than K-type stars.

The star with the highest surface temperature among these three classifications is a main-sequence B star. A, F, G, K, and M stars, which make up the majority of main-sequence stars in the Milky Way galaxy, are hotter and less massive than B-type stars. B stars' surface temperatures typically vary from 10,000 to 30,000 Kelvin (K), with some of the hotter stars exceeding 30,000 K. Surface temperatures of K-type giants range from around 3,500 to 5,000 K, whereas those of A-type supergiants range from about 7,500 to 11,000 K.

Learn more about surface temperature here:

https://brainly.com/question/5344945

#SPJ4

which of the following includes all common types of radioactive decay? a. atomic number, beta particle emission, electron capture B. alpha particle emission, beta particle emission, half-life C. alpha particle emission, beta particle emission, radioactive parent isotope D. alpha particle emission, beta particle emission, electron capture E. alpha particle emission, stable daughter, electron capture

Answers

Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.

They are common types of radioactive decay's because:

Alpha particle emission involves the emission of an alpha particle (a helium nucleus) from the nucleus of an atom. This reduces the atomic number by 2 and the mass number by 4.Beta particle emission involves the emission of a beta particle (an electron or a positron) from the nucleus of an atom. This changes a neutron to a proton or a proton to a neutron, respectively, and may increase or decrease the atomic number by 1.Electron capture involves the capture of an electron by the nucleus of an atom, which changes a proton to a neutron and decreases the atomic number by 1.

Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer

To learn more about radioactive decay:

https://brainly.com/question/11117468

#SPJ11

which of the following is true regarding adipocere? 1. also known as grave wax. 2. created by a hydrolysis reaction. 3. is chemically similar to a soap. 4. is created from a carbohydrate.

Answers

Adipocere, also referred to as corpse wax, grave wax, or mortuary wax is an organic substance with a wax-like texture that results from the hydrolysis of fat in tissues, including body fat in deceased bodies, by anaerobic bacteria.

Option 1 is true: Adipocere is also known as grave wax.

Option 2 is partially true: Adipocere is formed by a chemical reaction called saponification, which is the breakdown of fats in adipose tissue by the hydrolysis action of enzymes or bacteria.

Option 3 is true: Adipocere is chemically similar to soap because it is a type of fatty acid salt, specifically a calcium or magnesium salt of fatty acids.

Option 4 is false: Adipocere is not created from a carbohydrate, but rather from the breakdown of fat in the body.

Learn more about saponification:

https://brainly.com/question/14018257

#SPJ11

Find the angle ϕ between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value. Express your answer in degrees to four significant figures

Answers

"The required angle Ф between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value is 65.9°."

A photographer wants to click a picture of a cloud formation, the ratio of clouds intensity to that of the blue sky photographer uses polarizing filter from Malus law,

I = I₀ cos²Ф

So, I f = I i cos²Ф

As the light from cloud is polarized, its intensity reduces to half.

I c = I₀/2

The intensity of light from sky is polarized light.

I s = I₀ cos²Ф

Hence, the ratio of intensities is,

I c/I s = (I₀/2)/(I₀ cos²Ф)

3 = (I₀/2)/(I₀ cos²Ф)

cos²Ф = 1/6

Thus, the required angle is Ф = cos⁻¹(1/√6) = 65.9°

To know more about angles:

https://brainly.com/question/28562350

#SPJ4

I need help with this please

Answers

The answer is neutral

Answer:

It is positive

Explanation:

The area is only concentrated with red protons

Now, select the Slits simulation at the bottom of the screen, and Light (red) for the type of wave, as before. Also, make sure there is a barrier with one slit, and use the tape measure as well as the slider bar below the slit to place it roughly 1290 nm away from the light source. Adjust the slit width to 300 nm. Finally, select the start button at the source location to begin producing the waves. Which statement best describes how the intensity of the wave depends on position along the screen? Selecting the Intensity checkbox will show a plot of the intensity on the screen. a)The intensity is large near the middle of the screen, then decreases to nearly zero, and then increases again as the distance from the middle of the screen increases. b)The intensity is a maximum near the middle of the screen (directly to the right of the source) and significantly decreases above and below the middle of the screen. c)The intensity is roughly constant.

Answers

Light intensity can be estimated using either the total wave output, luminosity, or brightness.

Thus,  It is a measurement of the amount of power either emitted or reflected by a source. Intensity and luminosity work together to determine brightness.

Luminosity is the most widely used unit to measure light intensity because scientists typically find that examining the entire output spectrum is the most beneficial.

The intensity of light formula becomes eqI = fracLA/eq when luminosity L is substituted. The surface area of a sphere must be used as the denominator in the calculation to appropriately measure light intensity because light waves propagate in all directions.

Thus, Light intensity can be estimated using either the total wave output, luminosity, or brightness.

Learn more about Light intensity, refer to the link:

https://brainly.com/question/31790670

#SPJ12

1. A particle traveling around a circle at constant speed will experience an acceleration. - True or false2. The test-mass is referred to as m and it hangs from the test-mass riser. - True or false3. A particle travels 17 times around a 15-cm radius circle in 30 seconds. What is the average speed (in m/s) of the particle?- .5327 m/s4. What measurements will be made to determine the magnitude of the test-mass centripetal acceleration?- items 3 and 6(1) The mass of the test-mass.(2) The velocity of the test-mass.(3) The radius of the circular path.(4) The mass of the hanging mass.(5) The spring constant.(6) The period of the orbital motion.5. Before rotating the platform, the hanging mass is disconnected from the test mass and removed from the platform.- True or false6. A particle in uniform circular motion requires a net force acting in what direction? - towards the center of the circle7. The centripetal force acting on a particle is given byF = mv2/r. If the centripetal force and mass are kept constant, increasing the radius of the particle's circular path will mean that the particle's velocity must increase.- True or false

Answers

1. True.

2. True

3. The average speed of the particle is .5327 m/s.

4. All the given option will be made to determine the magnitude of the test-mass centripetal acceleration.

5.  True.

6. A particle in uniform circular motion requires a net force acting towards the center of the circle.

7. True.

1. A particle traveling around a circle at constant speed will experience an acceleration because it is changing its direction and this requires an acceleration.

So statment is True.

2. The test-mass is referred to as m and it hangs from the test-mass riser. So statment is True.

3. This can be calculated using the equation

speed = distance / time

In this case, the distance is

2π * 15 cm = 94.25 cm

and the time is 30 seconds,

so the speed is 94.25 cm / 30 s = .5327 m/s.

4. To determine the magnitude of the test-mass centripetal acceleration, measurements will need to be made of the following items:

(1) the mass of the test-mass,

(2) the velocity of the test-mass,

(3) the radius of the circular path,

(4) the mass of the hanging mass,

(5) the spring constant, and

(6) the period of the orbital motion.

5. Before rotating the platform, the hanging mass is disconnected from the test mass and removed from the platform.

6. A particle in uniform circular motion requires a net force acting towards the center of the circle.

7. True. If the centripetal force and mass are kept constant, increasing the radius of the particle's circular path will mean that the particle's velocity must increase. This is because the centripetal force is equal to the mass of the particle multiplied by the velocity of the particle squared, divided by the radius. Therefore, as the radius increases, the velocity of the particle must increase in order to keep the centripetal force constant.

For similar question circular motion

https://brainly.com/question/106339

#SPJ11

Pensacola and Admiralty Head have very different tidal characteristics. Describe how a difference in location, shape of shoreline, and lunar declination likely contributes to the difference in tidal ranges and tidal patterns for these two locations.

Answers

The difference in location, shape of shoreline, and lunar declination likely contributes to the difference in the tidal ranges and tidal patterns for the two locations include landmasses and wave interaction.

What are tidal characteristics?

The difference in tidal characteristics between Pensacola and Admiralty Head is likely due to the difference in location, shape of shoreline, and lunar declination. Location affects tidal ranges and patterns due to how different landmasses will interact with the waves.

The shape of the shoreline affects how the tides reflect and move in different directions. Lastly, lunar declination is a factor because the angle at which the moon is orbiting the earth affects the tides. This is because the gravitational pull of the moon varies with its distance and declination.

The differences in tidal characteristics between Pensacola and Admiralty Head can be attributed to the difference in location, shape of shoreline, and lunar declination, all of which have a direct impact on the tidal ranges and patterns of these two locations.

Learn more about Tidal characteristics here:

https://brainly.com/question/17587757

#SPJ11

if stars a and b are both main-sequence stars and star a has a greater fusion rate than star b, which of the following statements hold(s)? check all that apply. A. star a must be more luminous than star b. B. star a must be less luminous than star b. C. star a must be more massive than star b. D. star a must be less massive than star b.

Answers

If stars A and B are both main-sequence stars and star A has a greater fusion rate than star B, the following statements hold:

A. Star A must be more luminous than star B.

C. Star A must be more massive than star B.

This is due to the direct relationship between a main-sequence star's brightness and mass and the rate of fusion in that star. A higher fusion rate, therefore, suggests a higher brightness and mass.

StarA star is a large, bright ball of gas that is held together by its own gravity. They create the energy and light that enable life on Earth and serve as the foundation of galaxies.In space, gas and dust clouds collide under the force of their own gravity to generate stars.Nuclear fusion starts when the cloud's center reaches roughly 10 million degrees Celsius as it warms up and falls. This is how hydrogen atoms come together to create helium, unleashing a massive quantity of energy in the form of heat and light.The star can retain a steady size and form because the energy produced by fusion produces an outward pressure that balances the pull of gravity.

learn more about luminous here

https://brainly.com/question/25030787

#SPJ1

The major types of stress are ___ A. Ductile and Brittle B. Compression, Ductile, and Brittle C. Compression, Strain, and Deformation D.Shear, Tension and Compression E. Shear, Ductile, Tension, Brittle, and Compression

Answers

The major types of stress are shear, Tension, and Compression. Therefore option D is correct.

Stress refers to the internal forces acting on a material, causing it to deform or change shape. Different types of stress can act on a material, and they are characterized by the way in which the forces are applied.

1. Shear stress: Shear stress occurs when two forces act parallel to each other but in opposite directions, causing the material to deform by sliding or shearing.

2. Tension stress: Tension stress occurs when forces are applied to pull a material apart. It leads to elongation or stretching of the material.

3. Compression stress: Compression stress occurs when forces are applied to squeeze or compress a material.

Therefore, the correct answer is D. Shear, Tension, and Compression, as these three options represent distinct types of stress commonly encountered in materials and structures.

Know more about internal forces:

https://brainly.com/question/20639242

#SPJ4

The major types of stress are Shear, Tension and Compression.  The correct option is D.

Thus, Shear stress, tension stress, and compression stress are the three main forms of stress.

Shear stress is a condition when forces acting in opposite directions and parallel to a surface cause the material to deform by sliding or shearing. It is connected to the propensity for one layer of material to slide or move in relation to another layer.

Tension stress, sometimes referred to as tensile stress, is the strain that develops when a material is subjected to pulling or stretching forces that are applied in opposition to one another, causing the material to elongate. The material tends to be pulled apart by tension stress.

Thus, The major types of stress are Shear, Tension and Compression.  The correct option is D.  

Learn more about Shear stress, refer to the link:

https://brainly.com/question/20630976

#SPJ12

a roller coaster starts from rest at the top of a hill that is 18 m high. the car travels to the bottom of the hill and continues up the next hill which is 10 m high. how fast is the car moving at the top of the 10.0 m hill if friction is ignored?

Answers

The car is moving at a fast speed of 14.4 m/s at the top.

The formula for finding the velocity of the roller coaster is shown below: ½mv2=mgh.

Here,m is the mass of the roller coaster,v is the velocity of the roller coaster,

g is the acceleration due to gravity (9.8 m/s²), andh is the roller coaster's height above the ground.

At the top of the first hill, the roller coaster has a potential energy ofmgh=mg (18) = 18mg

Where,m is the mass of the roller coaster andg is the acceleration due to gravity (9.8 m/s²).

The velocity at the bottom of the first hill can be found using the conservation of mechanical energy:

kinetic energy + potential energy = kinetic energy + potential energy

½mv2 + mgh = ½mv2 + mghv2 = 2gh

At the bottom of the first hill, the kinetic energy is mgh.

The total mechanical energy at the bottom of the hill is thus mgh + mgh = 2mghv

2 = 2gh = 2 × 9.8 × 18v2 = 352.8v = 18.79 m/s

At the top of the second hill, the roller coaster's mechanical energy is once again equal to its potential energy:

potential energy = mgh = mgh = 10mgv = sqrt(2gh) = sqrt(2 × 9.8 × 10) = 14.4 m/s

Therefore, the velocity of the car at the top of the 10.0 m hill is 14.4 m/s.

To learn more about car, click here:

https://brainly.com/question/111325

#SPJ11

a piano tuner uses a tuning fork to adjust a piano wire to certain frequency. how does the piano tuner do this (select all that apply)?

Answers

Adjust the tension in the piano wire using a tuning wrench until the beats or interference disappear, indicating that the frequencies are now the same.

What is Frequency?

Frequency is the number of cycles of a periodic wave that occur in a given unit of time.  The higher the frequency, the more cycles occur per unit of time, and the higher the pitch of the sound wave associated with the frequency. In general, frequency is used to describe any regularly recurring event or pattern, such as the oscillation of a pendulum, the vibration of a guitar string, or the electromagnetic waves that make up light and radio signals.

The piano tuner uses the following methods to adjust a piano wire to a certain frequency:

Strike the tuning fork to create a pure tone with a known frequency.

Hold the tuning fork close to the piano wire and listen for any beats or interference between the two frequencies.

Verify the tuning using a piano tuning app or a reference tone, if necessary.

Learn more about Frequency from given link

https://brainly.com/question/254161

#SPJ1

The 6-kg collar has a velocity of 2 m/s to the right when it is at A It then travels along the smooth guide shown. The spring has an unscratched length of 100 mm and B is located just before the end of the curved portion of the rod.

Answers

The speed of the collar when its center reaches point B is 1.4 m/s.

The velocity of the 6-kg collar when its center reaches point B can be determined using the concepts of velocity, spring length, and conservation of energy.

The equation for conservation of energy is E = 1/2 mv² + 1/2 kx², where m is the mass of the object, v is the velocity, k is the spring constant, and x is the displacement of the spring.

At point A, the initial velocity is 2 m/s and the displacement of the spring is 0, so the total energy is

E = 1/2(6kg)(2m/s)².

At point B, the displacement of the spring is 100mm, so the total energy is

E = 1/2(6kg)(v²) + 1/2k(0.1m)²

Setting these equations equal to each other and solving for v, the velocity of the collar at point B is 1.4 m/s.

Learn more about conservation of energy on:

https://brainly.com/question/166559

#SPJ11

You are the process engineer at Corvallis Automobiles Inc., and you have received an order to turn a cylindrical bar on an engine lathe to the dimensions specified in Fig. 1. For this order you will use cylindrical bar stock that is 48-inches long and 4-inches in diameter. The 48-inch length bar will be chucked in the lathe and supported at the opposite end using a live center. You are planning to complete the operation in one pass using a cutting speed of 400 ft./min. and a feed of 0.010 in./rev. Determine the following: a) The required depth of cut (in inches) b) The material removal rate (in cubic inches per minute)
c) The time required to complete the cutting pass (in minutes)

Answers

a.  the depth of cut  is 0.625 inches.

b. the material removal rate is 0.003125 cubic inches per minute.

c. the time required to complete the cutting pass is 20 minutes.

How do we calculate?

a) The required depth of cut can be determined by :

DOC = (4 in - 2.75 in)/2 = 0.625 in

Therefore, the depth of cut is  0.625 inches.

b) The material removal rate can be found by applying:

MRR = DOC x Width of cut x Feed rate

assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.

MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute

c) The time required to complete the cutting pass is determined by:

Time = Length of cut / (Cutting speed x Width of cut x Feed rate)

Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes

Learn more about material removal rate  at: https://brainly.com/question/13106351

#SPJ1

Given the definition of EER, find the EER of an 8000 Btu/hour air conditioner that requires a power input of 1500 W. Express your answer numerically in British thermal units per hour per watt. EER = __________(Btu/hour)/W

Answers

EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.

The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.

In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:

EER = (cooling capacity in Btu/hr) / (power input in watts)

EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.

Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.

Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.

To know more about power:https://brainly.com/question/11569624

#SPJ11

if a satellite circulate around the earth at a height of 7323.77km above the earth's surface, given the earth radius is 3958.8 miles and mass is 5.98 x 10 kg, use G=6.674 X 10^-11 Nm^2/kg^2. find the perios of this satellite in unit hours? _______

Answers

The period of the satellite circulating the earth at the height of 7323.77km above the earth's surface is 2.14 hours.

We know that the radius of the Earth is 3958.8 miles, i.e. 6371 km, the mass of the Earth is 5.98*10²⁴kg and the height of the satellite is 7323.77 km

The formula used to find the period of a satellite is given by:-

[tex]T = 2\pi\sqrt{\frac{r^3}{GM}}[/tex]

Where, T = Period of the satellite, r = Radius of the satellite from the center of the earth, G = Gravitational constant, and M = Mass of the Earth.

We know that the height of the satellite from the surface of the earth is given by:-

[tex]R = r + h[/tex]

Where R = Radius of the earth, h = Height of the satellite from the surface of the earth.

Substituting the given values,

R = 6371 + 7323.77 = 13694.77 km = 8.5 miles

Therefore,

r = 13694.77 km

T = [tex]2\pi \sqrt \frac{r^3}{GM}[/tex]

  = [tex]2\pi \sqrt\frac{13694.77^3}{(6.674 * 10^{-11} * 5.98 * 10^{24})}[/tex]

T = 128.85 minutes

Now, convert the time from minutes to hours by dividing by 60:-

Period of the satellite = T = 128.85/60 = 2.14 hours

Learn more about mass: https://brainly.com/question/25959744

#SPJ11

what did oersted discover about electricity and magnetism

Answers

Hans Christian Oersted established the connection between electricity and magnetism in 1820. The magnetic field produced by the current revolves around the wire in a circle.

Oersted demonstrated how a magnetic field may be produced by moving electrons by establishing a compass through a wire carrying an electric current.

Scientists believed that electricity and magnetism had no connection until the discovery of electromagnetism. Hans Christian Oersted, a scientist from Denmark, revolutionised all of that. He found that an electric current in a wire may cause a magnetic field, as evidenced by the fact that the current can cause a magnetised compass needle to deflect.

The electrons in the wire are pushed when a coil of wire is moved around a magnet or vice versa, producing an electrical current. In essence, kinetic energy—the energy of motion—is transformed into electrical energy via electricity generators.

Learn more about Electricity here:

https://brainly.com/question/12791045

#SPJ4

on a sunny day, a rooftop solar panel delivers 55 w of power to the house at an emf of 17 v . part a how much current flows through the panel? express your answer with the appropriate units.

Answers

On a sunny day, a rooftop solar panel delivers 55 w of power to the house at an emf of 17 v . the current flows through the panel is  3.235 A.

What is the current flows through the panel?

The amount of current flowing through the panel can be calculated using Ohm's Law (I = p/v). When working with the formula, Power = Voltage × Current (P = V × I), one can determine the current that flows through the panel by rearranging the formula to:

Current = Power/Voltage (I = P/V).

The calculation of the current (I) is given as follows: I = P/V = 55 W / 17 V = 3.235 A.

Therefore, 3.235 A of current flows through the solar panel on a sunny day.

Read more about current here:

https://brainly.com/question/12785175

#SPJ11

1 80 kg scaffold is 5.80 m long. it is hanging with two wires, one from each end. a 580 kg box sits 1 m from the left end. what is the tension in the right hand side wire?

Answers

The tension in the right-hand side wire is 6525 N.

Given:

Weight of the scaffold = 180 kgLength of the scaffold = 5.8 mWeight of the box = 580 kgDistance of the box from left end = 1 mLet the tension in the left wire = T1Let the tension in the right wire = T2

To find: Tension in the right-hand side wireWe know that the sum of forces acting in a vertical direction should be equal to 0 as there is no acceleration in the vertical direction. ∑Fv = 0In the horizontal direction, there are no forces acting on the system.

∑Fh = 0Now considering forces in the vertical direction: T1 + T2 = (Weight of scaffold + Weight of the box) gT1 + T2 = (180 + 580) x 9.8T1 + T2 = 7644 N1. From the diagram, we can see that the box is nearer to the left side. Hence, the tension force in the left wire is greater than the tension force in the right wire.

T1 > T22. Let's take moments about the right end of the scaffold as shown in the figure below.

∑Mr = 0T1 × 5.8 = T2 × 1T2 = 5.8/1 × T1T2 = 5.8T1

Now, we can substitute the value of T2 in equation (1):

T1 + T2 = 7644N6.8 T1 = 7644 N  T1 = 1125 N

To find T2, we can substitute the value of T1 in equation (2):

T2 = 5.8 × T1T2 = 5.8 × 1125 N T2 = 6525 N

Therefore, the tension in the right-hand side wire is 6525 N.

Learn more tension: https://brainly.com/question/4001686

#SPJ11

consider two planets in space that gravitationally attract each other. if the masses of both planets are doubled, and the distance between them is also doubled, then the force between them is group of answer choices four times as much. half as much. twice as much. remains the same. one quarter.

Answers

If the masses of two planets in space that gravitationally attract each other are doubled and the distance between them is also doubled, then the force between them remains the same.

To determine the force between two planets, we use the formula:

F = Gm1m2/r^2

where F is the force of gravitational attraction between the two planets, G is the gravitational constant, m1 and m2 are the masses of the planets, and r is the distance between them.

If both masses are doubled and the distance between them is also doubled, the new force between them can be calculated as follows:

F' = G(2m1)(2m2)/(2r)^2

Simplifying this expression, we get:

F' = Gm1m2/r^2

which is the same as the original force between the planets.

Therefore, if the masses of two planets are doubled and the distance between them is also doubled, the force between them remains the same.

For more similar questions on gravitation and physics:

brainly.com/question/27996005

#SPJ11

Which statement describes what most likely occurs when a magnetic compass is placed next to a simple circuit made from a battery, a light bulb, and a wire?A magnetic field created by the compass causes the light bulb to stop working.A magnetic field created by the electric current causes the compass needle to move.A magnetic field created by the compass increases the current in the electrical circuit.A magnetic field created by the electric current places negative charges on the compass.

Answers

A magnetic field created by the electric current causes the compass needle to move. This is the most likely outcome when a magnetic compass is placed adjacent to a basic electrical circuit consisting of a battery, a light bulb, and a wire.

A magnetic field is created around a wire as electricity flows through it. The compass needle moves as a result of the interaction between this magnetic field and the Earth's magnetic field. Consequently, the magnetic field produced by the electric current in the wire causes the compass needle to move when a magnetic compass is put next to a basic circuit comprised of a battery, a light bulb, and a wire. The interplay of magnetic fields and electric currents is employed in numerous applications, such as electric motors and generators, to transform electrical energy into mechanical energy and vice versa.

learn more about magnetic compass here:

https://brainly.com/question/2264542

#SPJ4

when the air is in geostrophic balance, it flows _______ to isobars _________ the boundary layer.

Answers

When the air is in geostrophic balance, it flows parallel to isobars  and above the boundary layer.

Geostrophic balance is a state of balance between the pressure gradient force and the Coriolis force, where the pressure gradient force is directed from higher to lower pressure, and the Coriolis force is perpendicular to the direction of motion. In this state, the wind flows parallel to the isobars, with the pressure gradient force and the Coriolis force balancing each other out.

The boundary layer is the layer of air near the Earth's surface where friction between the air and the surface slows down the wind and causes it to flow in a more complex manner, with the wind direction changing with height. However, in the geostrophic flow regime, the wind flow is typically above the boundary layer and thus not affected by surface friction.

Therefore, in geostrophic balance, the wind flows parallel to isobars and above the boundary layer, with little to no effect from the Earth's surface.

Learn more about geostrophic balance here

brainly.com/question/28314662

#SPJ4

Give a counterexample to show that the following construction fails to prove that the class of context-free languages is closed under the star operation. Let A be a CFL that is generated by the CFG G = (V, σ, R, S). Add the new rule S → SS and call the resulting grammar G0 . It is hoped that G0 generates A∗ .

Answers

Consider the following counterexample to prove that the construction fails to prove that the class of context-free languages is closed under the star operation:

Let A be a context-free language that consists of only one word "a".

So, the grammar for A would be as follows: G = ({S}, {a}, {S → a}, S)

Let A* be the concatenation of any number of words of A including 0 words.

Hence, A* = {ε, a, aa, aaa, aaaa, …}

Now, construct G0 by adding the new rule S → SS to G.

So, the grammar G0 would be as follows: G0 = ({S}, {a}, {S → a, S → SS}, S)

According to the construction, we can say that G0 generates A* if A is a context-free language.

However, A* can be shown as not context-free using pumping lemma for context-free languages.

Hence, we can say that G0 does not generate A* although A is a context-free language. Thus, the construction fails to prove that the class of context-free languages is closed under the star operation.

To know more about "context-free language" refer here:

https://brainly.com/question/29762238#

#SPJ11

The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. The properties of the junction are k = 35 W/m °C, rho= 8500 kg/m3 ,and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m2 °C. Determine how long it will take for the thermocouple to read %95 of the initial temperature difference.

Answers

It will take about 12.12 minutes for the thermocouple to read 95% of the initial temperature difference of the sphere. This is due to difference in temperature.

What is the time required to read 95% of initial temperature difference?

In order to determine how long it will take for the thermocouple to read 95% of the initial temperature difference, the following formula is used:

t = (rho × V × Cp)/(h × pi × D) × ln ((Tinitial - T∞) / (Tinitial - Tcutoff))

where, t = time (s), ρ = density (kg/m³), V = volume (m³), Cp = specific heat capacity (J/kg °C), h = heat transfer coefficient (W/m²°C), D = diameter (m), Tinitial = initial temperature (°C), T∞ = surrounding temperature (°C), Tcutoff = temperature at which the thermocouple reading is 95% of the initial temperature difference (°C).

Substituting the given values into the above formula:

t = (8500 kg/m³ × (4/3 × pi × (0.0006 m)³)) / (65 W/m2 °C × pi × 0.0012 m) × ln ((100 °C - 25 °C) / (100 °C - 95 °C))

t = 727.31 s or 12.12 minutes.

Therefore, it will take approximately 12.12 minutes for the thermocouple to read 95% of the initial temperature difference.

Learn more about Thermocouple here:

https://brainly.com/question/14555057

#SPJ11

calculate the magnitude of the gravitational field of the sun at the location of earth, in meters per square second.

Answers

The magnitude of the gravitational field of the Sun at the location of Earth is approximately 9.81 m/s2.

This value is derived from Newton's Law of Universal Gravitation, which states that the gravitational force (F) between two objects is equal to the product of the two objects' masses (m1 and m2) multiplied by the gravitational constant (G) divided by the square of the distance between the two objects (r2):
F = G * m1 * m2 / r2
The mass of the Sun is 1.989 × 1030 kg, and the average distance between Earth and the Sun is 1.496 × 1011 meters. Therefore, plugging those values into the equation gives us:
F = 6.67 × 10-11 * 1.989 × 1030 * 5.972 × 1024 / (1.496 × 1011)2
F = 9.81 m/s2

Read more about the topic of gravitation:

https://brainly.com/question/72250

#SPJ11

I need help with this question

Answers

The gardener does 5600 joules of work in pushing the wheelbarrow around the lawn.

Step-by-step calculation:

The distance traveled by the wheelbarrow is the perimeter of the lawn, which is:

Perimeter = 3 m + 4 m + 3 m + 4 m = 14 m

The net force exerted on the wheelbarrow is the sum of the force used to push it along the ground and the force used to lift it off the ground:

Net force = 100 N + 300 N = 400 N

The angle between the force and the direction of motion is 0 degrees, so the cosine of the angle is 1.

The work done by the gardener is given by:

Work = Force x Distance x cos(theta)

Substituting the values we found above, we get:

Work = 400 N x 14 m x cos(0 degrees)

Work = 5600 J

Therefore, the gardener does 5600 joules of work in pushing the wheelbarrow around the lawn.

To know more about perimeter, visit:

https://brainly.com/question/6465134

#SPJ1

Which turbine takes the lesser amount of time to rotate through 1.0 radian of angular displacement? a. turbine A b. turbine B c. They take the same amount of time. d. The answer cannot be determined from the information given.

Answers

The correct option is C, The turbine that takes the lesser amount of time to rotate through 1.0 radian of angular displacement is both because They take the same amount of time.

A turbine is a device that converts kinetic energy from a fluid (such as water, steam, or air) into mechanical energy. It is composed of a series of rotating blades that are attached to a shaft. When the fluid flows over the blades, it causes them to rotate, which in turn rotates the shaft.

Turbines are commonly used in power generation to generate electricity. For example, in a hydroelectric power plant, water flows through a turbine, which spins a generator to produce electricity. Similarly, in a gas or steam turbine power plant, the combustion of fuel heats up air or water to create steam, which flows through a turbine to produce electricity.

To learn more about Turbine visit here:

brainly.com/question/30559123

#SPJ4

phase of the moon where only a very small part of the lit surface is seen from earth is called?

Answers

The phase of the moon where only a very small part of the lit surface is seen from the earth is called the crescent moon phase.

This phase occurs when the illuminated portion of the moon is less than half, but not yet a new moon. When the crescent moon appears in the sky, it is usually visible in the west just after sunset and looks like a thin curved shape. The crescent moon is visible for a few days, after which it transitions into the first quarter moon phase. The phases of the moon are a result of the moon's changing position relative to the sun and the earth.

As the moon orbits the earth, different parts of its surface are illuminated by sunlight. This is why we see different phases of the moon as it rotates around the earth. The phases of the moon include the new moon, waxing crescent, first quarter, waxing gibbous, full moon, waning gibbous, third quarter, and waning crescent. The crescent moon phase is just one of these eight phases.

To learn more about Moon :

https://brainly.com/question/13086036

#SPJ11

Other Questions
sandwich chain whose name is french for ready to eat is called how is the mesosphere formed A block of mass 2kg is attached to the spring of spring constant 50Nm 1. The block is pulled to a distance of 5 cm from its equilibrium position at x=0 on a horizontal frictionless surface from rest at t = 0. The displacement of the block at any time t is thenA. x= 0.05sin5tmB. x= 0.05cos5tmC. x= 0.5sin5tmD. x= 5sin5tm an equation of a circle is given by (x+3)^2+(y_9)^2=5^2 apply the distributive property to the square binomials and rearrange the equation so that one side is 0. true or false in determining the cost of debt, a firm could use its yields and prices of outstanding bonds. true/false. the sole proprietorship form of ownership tends to be attractive to people who want to invest in a company without taking an active role in management. during the process of transcription, the information in When the conductivity is at a minimum, what must be true about the amount of Ba(OH)2 compared to H2SO4?Why does it not conduct at this low point?Why does it conduct more before and after this minimum point? Respond to the following in a minimum of 175 words: Share a time when you experienced conflict within a team... What strategies did you and your team members use to manage and resolve the conflict? Were thesestrategies successful? Why or why not? How could you apply the strategies presented this week to reach a more effective outcome?Due Monday When you execute a new script you've written, one of the environment variables you created in your current shell for use in that script doesn't appear to be present. Which of the following commands would help you to fix this issue? In THE BRIEF WONDROUS LIFE OF OSCAR WAO What was the purpose of The Three Heartbreaks of Belicia Cabral 1955-62? How did this long chapter broaden and deepen the themes and the message of The Brief Wondrous Life of Oscar Wao? How does it relate to the plot and themes of Oscar and Lolas stories? a)- On which day does ovulation occur? I need some help please Which of the following account assignment categories is used when the company acquires a fixed asset?a. Cost centerb. Assetc. Orderd. Sales ordere. Project Miko bought five 2-litre bottles of water. She poured all the water equally into 15 bowls. What was the volume of water in each bowl? When adding an item to an array-based list with an allocation size equal to the list length, a new array is generally allocated with ______ the current length.a. the same size asb.one less thanc.one more thand.twice you suspect that the gshant user account is locked. enter the command you would use in a shell to show the status of the user account. How many molecules of oxygen are produced by the decomposition of 6. 54 g of potassium chlorate (KCLO3)? How is the momentum of an object determined?What happens every time one of the boys playing ping pong hits the ball?How could the boy playing ping pong keep from hitting the ball off the table? I GIVE 20 PTS PLS HEELP find the value of x in the following figure