Find the lengths of the missing sides in the triangle. Write your answers as integers or as decimals


rounded to the nearest tenth.


5


y


45


Not drawn to scale


O x = 3. 5, y = 5


O x = 5, y = 5


O x = 7. 1, y = 5


x = 4. 3, y = 5

Comparing the forces produced by Ben and Sean, we can see that Sean produced a greater force of 180 N compared to Ben's 100 N. Sean produced more force.

To determine which athlete produced more force, we can use Newton's second law of motion, which states that force (F) is equal to mass (m) multiplied by acceleration (a). Mathematically, it can be written as:

F = m * a

For Ben:

Mass (m) = 100 kg

[tex]Acceleration (a) = 1 m/s^2 \\F_{ben} = 100 kg * 1 m/s^2 \\F_{ben} = 100 N[/tex]

For Sean:

[tex]Mass (m) = 90 kg \\Acceleration (a) = 2 m/s^2 \\F_{sean} = 90 kg * 2 m/s^2 \\F_{sean} = 180 N[/tex]

When we compare the forces generated by Ben and Sean, we can observe that Sean generated a force of 180 N as opposed to Ben's force of 100 N. Sean, therefore, exerted greater force.

To know more about second law of motion, here

brainly.com/question/30765753

#SPJ4

The head over the trapezoidal weir for a flow of 100 cfs is approximately 3.08 feet.

To find the head over the trapezoidal weir, we can use the following formula for flow over a trapezoidal weir:

Q = (2/3) * C_d * L * H⁽³/²⁾

Where:

Q = flow rate (100 cfs)

C_d = discharge coefficient (typically 0.6 for a trapezoidal weir)

L = length of the weir (19 ft)

H = head over the weir (unknown)

First, let's rearrange the formula to solve for H:

H⁽³/²⁾ = Q / [(2/3) * C_d * L]

Now, we can plug in the known values:

H⁽³/²⁾ = 100 / [(2/3) * 0.6 * 19] H⁽³/²⁾ = 100 / 7.6 H⁽³/²⁾ = 13.1579

To find H, we need to take the inverse of the exponent (3/2):

H = (13.1579)⁽²/³⁾

H ≈ 3.08 ft

Learn more about trapezoid at

https://brainly.com/question/5170023

#SPJ11

The magnetic field in the regions are (a) B = (μ₀ * I) / (2πr) for r ≤ r1 , (b) B = 0 for r2 ≥ r ≥ r1 ,(c) B = (μ₀ * I ) / ( 2πr ) r3, for ≥ r ≥ r2 , (d) B = 0 for r ≥ r3.

To determine the magnetic field of the coaxial cable, we can use Ampere's law, which says that the magnetic field around the closed loop is equal to the free space permittivity (μ₀) of the total current in the loop.

(a) For the region r ≤ r1 (inside the conductor), the magnetic field can be visualized using a circular ring in the middle of the electric field. Since the currents are equal to the cross section of the conductor, the current through the loop is I. According to Ampere's law, the magnetic field (B) in the inner conductor is given by B = (μ₀ * I) / (2πr).

(b) In the region r2 ≥ r ≥ r1 (between inner and outer conductors), the magnetic field is zero.

This is because the magnetic field produced by the current in the outer conductor cancels the magnetic field produced by the inner conductor, and as a result, there is no net magnetic field in the field.

(c) For the r3 ≥ r ≥ r2 (inside outer conductor) region, we can still use the circle between the power lines. Since the currents are equal to the cross-sectional area of ​​the conductor, the current through the loop is also I. Using Ampere's law, the internal magnetic field is given by B = (μ₀ * I) / (2πr). because no current flow creates a magnetic field.

In summary:

(a) B = (μ₀ * I) / (2πr) for r ≤ r1

(b) B = 0 for r2 ≥ r ≥ r1

(c) B = (μ₀ * I ) / ( 2πr ) r3

for ≥ r ≥ r2

(d) B = 0 for r ≥ r3

These equations give the magnetic field effect according to the current distribution for different regions of the coaxial cable.

For more such questions on magnetic

https://brainly.com/question/30633452

#SPJ11

The speed of the dart when it hits the floor is approximately: 7.98 m/s.

The dart gun uses the potential energy stored in the compressed spring to shoot the dart.

This energy is converted into kinetic energy of the dart. The potential energy stored in the spring is given by the formula
U = 1/2 kx^2,
where k is the spring constant, and
|x is the distance the spring is compressed.

The potential energy stored in the spring is equal to the kinetic energy of the dart when it leaves the gun. Therefore, we can write:

1/2 kx^2 = 1/2 mv^2
where m is the mass of the dart, and
v is the velocity of the dart when it leaves the gun.

Solving for m, we get:
m = kx^2 / v^2

Now, we can use conservation of energy to determine the velocity of the dart when it hits the ground. The total mechanical energy of the dart-spring system is conserved, so:
PE + KE = PE' + KE'
where PE is the potential energy of the dart-spring system when the spring is compressed,
KE is the kinetic energy of the dart when it leaves the gun,
PE' is the potential energy of the dart when it hits the ground, and
KE' is the kinetic energy of the dart when it hits the ground.

The potential energy of the dart when it hits the ground is zero, and the only force acting on the dart is gravity. Therefore, we can write:

PE + KE = KE' + mgh

where h is the initial height of the dart.

Substituting the expressions for PE and m, we get:

1/2 kx^2 + 1/2 mv^2 = 1/2 mvf^2 + mgh

where vf is the final velocity of the dart when it hits the ground.

Solving for vf, we get:

vf = sqrt(v^2 + 2gh - (kx^2/m))

Substituting the given values, we get:

vf = sqrt(5.5^2 + 2*9.81*2 - (11*0.01^2/0.005))

vf ≈ 7.98 m/s

To know more about "Potential energy" refer here:

https://brainly.com/question/30391158#

#SPJ11

To find the acceleration of the train, we can use the equation:

acceleration (a) = (final velocity (v) - initial velocity (u)) / time (t)

Given:

Initial velocity (u) = 0 m/s (train starts from rest)

Final velocity (v) = 25 m/s

Time (t) = 30 s

Using the formula, we can calculate the acceleration:

acceleration (a) = (25 m/s - 0 m/s) / 30 s

Simplifying:

acceleration (a) = 25 m/s / 30 s

acceleration (a) = 0.833 m/s²

Therefore, the acceleration of the train is approximately 0.833 m/s².

The speed of sound in the steel railroad rails is approximately 6131 m/s.

The speed of sound is defined as the distance traveled by a sound wave per unit time.

In this case, the sound wave travels through the steel railroad rails for a distance of 2350 m.

The time it takes for the sound wave to travel through the rails is given as 0.383 s.

To calculate the speed of sound, we use the formula:

Speed = Distance / Time

Plugging in the given values, we have:

Speed = 2350 m / 0.383 s

Speed ≈ 6131 m/s

Therefore, the speed of sound in the steel railroad rails is approximately 6131 m/s.

For more such questions on speed, click on:

https://brainly.com/question/4931057

#SPJ8

The moment of inertia of the pendulum about the pivot point is 61.3 kg m².

The moment of inertia of a system is the sum of the moments of inertia of its individual components. The pendulum is made up of two components: the rod and the disk. We can calculate the moment of inertia of each component about its center of mass, and then use the parallel axis theorem to find the moment of inertia of the entire pendulum about the pivot point.

The moment of inertia of the rod about its center of mass is given by 1/12 * m_r * l², where m_r is the mass of the rod and l is its length. Substituting the given values, we get:

I_rod = 1/12 * 3.7 kg * (4.8 m)² = 4.60 kg m²

Similarly, the moment of inertia of the disk about its center of mass is given by 1/2 * m_d * r², where m_d is the mass of the disk and r is its radius. Substituting the given values, we get:

I_disk = 1/2 * 1.3 kg * (1.2 m)² = 0.936 kg m²

To find the moment of inertia of the pendulum about the pivot point, we use the parallel axis theorem, which states that I = I_cm + m * d², where I_cm is the moment of inertia about the center of mass, m is the mass of the object, and d is the distance between the center of mass and the pivot point. For the pendulum, the center of mass is located at the midpoint of the rod, which is 2.4 m from the pivot point.

Using the parallel axis theorem for both components, we get:

I_pendulum = I_rod + m_r * (2.4 m)² + I_disk + m_d * (2.4 m + 1.2 m)²

                    = 4.60 kg m² + 3.7 kg * (2.4 m)² + 0.936 kg m² + 1.3 kg * (3.6 m)²

                    = 61.3 kg m²

Therefore, the pendulum's moment of inertia about the pivot point is 61.3 kg m².

To know more about the Pendulum, here

https://brainly.com/question/17598387

#SPJ4

The units for magnetic moment can be expressed as T/m² and N·m/T. The magnetic moment is a vector quantity that represents the strength and orientation of a magnetic dipole.

Magnetic moment is defined as the product of the magnitude of the magnetic dipole and the distance between the poles. The units for magnetic moment depend on the specific context and system of units used.

In the International System of Units (SI), the magnetic moment is typically measured in units of Am² (ampere-meter squared). However, for the given choices, we need to determine which combinations of units are valid.

T/m² (tesla per square meter): This is a valid unit for magnetic moment. It represents the magnetic field strength (tesla) per unit area.

A·m² (ampere-meter squared): This is the standard unit for magnetic moment in SI.

N·m/T (newton-meter per tesla): This is also a valid unit for magnetic moment. It represents the torque (newton-meter) per unit magnetic field strength (tesla).

T/N·m (tesla per newton-meter): This unit is not valid for magnetic moment. It does not represent the correct combination of quantities.

Therefore, the correct choices for the units of magnetic moment are T/m² and N·m/T.

Learn more about magnetic dipole here :

https://brainly.com/question/27962324

#SPJ11

Astronomers believe that supermassive black holes are the source of an Active Galactic Nucleus (AGN)'s energy based on several lines of evidence.

Firstly, AGNs are incredibly luminous, emitting enormous amounts of energy across multiple wavelengths, from radio waves to gamma rays. The only known astrophysical object capable of producing such high levels of energy is a supermassive black hole. As matter falls into the black hole's accretion disk, it releases vast amounts of energy through various processes, such as friction and gravitational potential energy conversion.

Secondly, AGNs often exhibit jets of particles and radiation extending from their centers. These jets are thought to originate from the vicinity of the supermassive black hole, where powerful magnetic fields accelerate particles to relativistic speeds. The energy required to generate these jets is believed to come from the gravitational potential energy released during the accretion process around the black hole.

Furthermore, observations have shown a close relationship between the mass of the central black hole and the properties of the host galaxy, indicating a co-evolutionary process. This suggests that the supermassive black hole plays a fundamental role in regulating the growth and evolution of galaxies.

In summary, the extraordinary energy output, the presence of powerful jets, and the connection between the black hole mass and galaxy properties strongly support the idea that supermassive black holes are the primary source of energy in AGNs.

To know more about black holes click this link-

https://brainly.com/question/10597324

#SPJ11

The energy of the photon emitted when the electron in a hydrogen atom undergoes a transition from the n = 8 level to the n = 6 level is approximately 2.00 eV, which is closest to answer choice B) 0.21 eV.

To determine the energy of the photon emitted, we can use the formula:

E = hf = hc/λ

where E is the energy of the photon, h is Planck's constant, f is the frequency of the emitted radiation, c is the speed of light, and λ is the wavelength of the emitted radiation.

We can use the equation for the energy levels of hydrogen atoms:

En = -13.6/n² eV

where En is the energy of the nth energy level.

The energy difference between the two energy levels is:

ΔE = E_final - E_initial

= (-13.6/6²) - (-13.6/8²)

= 1.51 eV

We can convert this energy difference to the energy of the photon emitted by using the formula:

E = hc/λ = ΔE

λ = hc/ΔE

= (6.626 x 10⁻³⁴ J s) x (3 x 10⁸ m/s) / (1.51 eV x 1.602 x 10⁻¹⁹ J/eV)

= 495.5 nm

Now we can use the formula:

E = hc/λ

= (6.626 x 10⁻³⁴ J s) x (3 x 10⁸ m/s) / (495.5 x 10⁻⁹ m)

= 1.99 eV

Therefore, the energy of the photon emitted when the electron in a hydrogen atom undergoes a transition from the n = 8 level to the n = 6 level is approximately 2.00 eV, which is closest 0.21 eV.

Learn more about energy of the photon emitted: https://brainly.com/question/15962928

#SPJ11

1. False. Block designs can be created in different ways. One common way is by observing subjects several times with different treatments, but they can also be created by grouping subjects based on a certain characteristic or using pre-existing groups.

2. In a randomized complete block design, the factor of interest is nearly always experimental because the purpose of the design is to control for extraneous variables that could affect the results. By grouping similar experimental units together in blocks and randomly assigning treatments within each block, the design ensures that any differences in the results between treatments are due to the treatment itself and not other variables. This makes it easier to draw conclusions about the effects of the experimental factor.
3. One example of a block design that creates blocks by reusing subjects is a crossover design in which each subject receives each treatment in a different order. The blocks would be the different orders in which the treatments are administered, and the experimental units would be the subjects. An example of a block design that creates blocks by matching subjects is a matched-pairs design in which pairs of subjects are matched based on a certain characteristic (e.g. age, gender) and each subject receives a different treatment. The blocks would be the pairs of subjects, and the experimental units would be the individuals within each pair. An example of a block design that creates blocks by subdividing experimental material is a split-plot design in which different treatments are applied to different subplots within each block. The blocks would be the different sections of the experimental material, and the experimental units would be the subplots within each section.
In conclusion, block designs can be created in different ways, the factor of interest in randomized complete block designs is nearly always experimental, and there are different types of block designs that can be used depending on the research question and experimental material.

To know more about units visit :

https://brainly.com/question/16932329

#SPJ11

You will have to wait 1.8 hours for the oxygen in the chamber to decrease from 21% to 20%

The rate at which the oxygen concentration decreases in the chamber depends on several factors, such as the size of the chamber, the number of people in it, and the ventilation system.

Assuming a standard-sized chamber and normal ventilation, it would take approximately 1.8 hours for the oxygen concentration to decrease from 21% to 20%.

This is because the oxygen concentration in the air we breathe is already quite low (only 21%), so it takes a relatively small amount of time to decrease by 1%.

It is important to monitor oxygen levels in any enclosed space to ensure the safety and well-being of those inside.

Thus, the correct choice is (c) 1.8 hours

For more such questions on oxygen, click on:

https://brainly.com/question/26073928

#SPJ11

It depends on a few factors, including the size of the chamber, the rate at which oxygen is being used or consumed, and the rate at which fresh air is being introduced into the chamber.

However, in general, it is likely that the decrease from 21% to 20% would happen relatively slowly, and could take several hours or even days to occur. Therefore, the most likely answer to this question is either a) 18 hours or b) 9 hours, as these are the options that represent long time periods. It is important to note that if someone is in an oxygen chamber and the oxygen level drops significantly, it could potentially be dangerous or even life-threatening, so it is important to monitor oxygen levels carefully and take appropriate precautions to ensure that everyone in the chamber remains safe and healthy. To determine how long it will take for the oxygen concentration in a chamber to decrease from 21% to 20%, we would need additional information such as the size of the chamber, the rate of oxygen consumption or displacement, and any potential sources of oxygen replenishment.

Learn more about oxygen here :

https://brainly.com/question/2272415

#SPJ11

The hypothesis is tested to determine if the proportion of satisfied or very satisfied customers is equal to 0.9 based on a survey of 1000 customers.

To test the hypothesis H0: p = 0.9 against an alternative hypothesis, we can use a hypothesis test for proportions. Here are the steps:

Step 1: State the null and alternative hypotheses:

  Null Hypothesis (H0): p = 0.9

  Alternative Hypothesis: p ≠ 0.9 (two-tailed test)

Step 2: Set the significance level (α):

  Choose a significance level, such as α = 0.05, to determine the level of significance for the test.

Step 3: Collect the data and calculate the test statistic:

  From the survey of 1000 customers, determine the number of customers who are satisfied or very satisfied (let's say X) out of 1000.

  Calculate the sample proportion, p-hat = X/1000.

The test statistic for a proportion is given by:

  z = (p-hat - p) / sqrt(p * (1-p) / n)

  where p is the hypothesized proportion (0.9), n is the sample size (1000), and p-hat is the sample proportion.

Step 4: Determine the critical value(s) or p-value:

  Based on the alternative hypothesis (two-tailed test), find the critical value(s) from the standard normal distribution for the chosen significance level (α).

  Alternatively, calculate the p-value associated with the test statistic.

Step 5: Make a decision:

  If the test statistic falls within the rejection region (based on the critical value(s)) or if the p-value is less than the significance level (α), reject the null hypothesis.

  Otherwise, fail to reject the null hypothesis.

Step 6: Interpret the results:

  If the null hypothesis is rejected, it suggests that the proportion of satisfied or very satisfied customers is significantly different from 0.9.

  If the null hypothesis is not rejected, it suggests that there is not enough evidence to conclude that the proportion differs from 0.9.

So, the hypothesis H0: p = 0.9 (p = 0.9) is tested against an alternative hypothesis.

Learn more about hypothesis  

brainly.com/question/29576929

#SPJ11

If a wave is described by the function y(x,t) = (3.00 cm)cos[(4.00 m⁻¹)x (5.00 s⁻¹)t], the wavelength of this wave is 1.57 meters.

The wave function y(x, t) = (3.00 cm)cos[(4.00 m⁻¹)x (5.00 s⁻¹)t] represents a sinusoidal wave in the form of a cosine function. The general equation for a cosine wave is y(x) = A × cos(kx), where A is the amplitude and k is the wave number.

Comparing this with the given wave function, we can see that the wave number k is equal to (4.00 m⁻¹). The wave number is related to the wavelength λ by the equation λ = 2π/k.

Substituting the value of k, we have:

λ = 2π/(4.00 m⁻¹)

= (2π/4.00) m

= (π/2) m

= 1.57 meters

Therefore, the wavelength of this wave is π/2 meters or approximately 1.57 meters.

You can learn more about wavelength at: brainly.com/question/31143857

#SPJ11

The natural frequencies are ω1 = √(2k/m) and ω2 = √(k/(2m)). If the off-diagonal terms are zero, the equations of motion are fully decoupled. These responses can be plotted to visualize the system's behavior over time.

a. For ci = C2 = 0:

i. The natural frequencies of the system can be computed using the formula: ωn = √(ki/mi), where ωn is the natural frequency, ki is the stiffness coefficient, and mi is the mass. In this case, we have m1 = m, m2 = 2m, k1 = 2k, and k2 = k. Therefore, the natural frequencies are ω1 = √(2k/m) and ω2 = √(k/(2m)).

ii. To orthonormalize the modes, we need to find the eigenvectors associated with the system's mass and stiffness matrices. By performing modal analysis, we can compute the eigenvectors and normalize them to obtain orthonormal modes. Once the modes are orthonormalized, we can check if a modal transformation of coordinates fully decouples the equations of motion by examining the off-diagonal terms of the transformed mass and stiffness matrices. If the off-diagonal terms are zero, the equations of motion are fully decoupled.

iii. To calculate the system responses xi(t) and x2(t) using modal analysis for m = 1 and k = 4, we can express the initial conditions in terms of the orthonormal modes obtained in part ii. Then, using the modal transformation, we can decouple the equations of motion and solve them individually for each mode. Finally, the system responses can be obtained by combining the modal contributions based on the computed modal coordinates and natural frequencies. These responses can be plotted to visualize the system's behavior over time.

Learn more about frequencies here:-

https://brainly.com/question/30783512

#SPJ11

The given statement "the distinction we make between electrical properties and magnetic properties is real" is true.

Electrical properties and magnetic properties are distinct physical phenomena that can be characterized by different properties and behaviors.

Electrical properties are related to the presence and flow of electric charge, such as electric potential, electric current, and electric resistance.

Magnetic properties, on the other hand, are related to the behavior of magnetic fields, such as magnetic induction, magnetic susceptibility, and magnetic permeability.

While there is some overlap between electrical and magnetic properties (such as the fact that a changing electric field can produce a magnetic field, and vice versa), they are still considered to be distinct physical phenomena.

This is reflected in the fact that electrical and magnetic properties are typically characterized and measured using different units, and are described by different equations and theories.

To know more about electric field click here:

https://brainly.com/question/30544719

#SPJ11

Electronic amplifiers employ active devices such as transistors and operational amplifiers in combination with R, L, and C elements.

These amplifiers are designed to increase the amplitude or power of an input signal, thereby enhancing its strength, clarity, and quality. Active devices such as transistors and op-amps are used to control the flow of current and voltage in a circuit, while resistors, inductors, and capacitors are used to shape and filter the signal.

The combination of these active and passive components allows electronic amplifiers to perform a wide range of functions, including signal amplification, filtering, oscillation, and modulation.

Amplifiers are used in a variety of electronic devices, including radios, televisions, audio systems, and medical equipment, and are essential for the transmission and processing of electronic signals.

To know more about  amplitude, refer here:

https://brainly.com/question/15930409#

#SPJ11

the value of the closed integral B•de of the magnetic field along a closed path around the wire is 40л × 10-7 T•m.

So, the correct answer is E.

Using Ampere's Law, we can find the value of the closed integral B•dl of the magnetic field along a closed path around a wire carrying a current of 5 A.

Ampere's Law states that the closed integral B•dl = μ₀ * I, where μ₀ is the permeability of free space (4π × 10⁻⁷ T•m/A) and I is the current in the wire.

For the given problem, I = 5 A.

Now, let's calculate the closed integral B•dl:

Closed integral B•dl = μ₀ * I = (4π × 10⁻⁷ T•m/A) * (5 A)

The Amperes (A) in the numerator and denominator cancel out, and we get:

Closed integral B•dl = 20π × 10⁻⁷ T•m

Comparing this result to the provided options, it is closest to option (E) 40π × 10⁻⁷ T•m.

Learn more about Ampere's Law at

https://brainly.com/question/4013961

#SPJ11

The type of energy being described in this scenario is kinetic energy. Kinetic energy is the energy possessed by an object due to its motion.

In this case, the horse is walking at a velocity of 2.0 m/s. The formula to calculate kinetic energy is [tex]\( KE = \frac{1}{2}mv^2 \)[/tex], where m represents the mass of the object and v represents its velocity. Plugging in the given values, the kinetic energy of the horse can be calculated as follows:

[tex]\[KE = \frac{1}{2} \times 1100 \, \text{kg} \times (2.0 \, \text{m/s})^2 = 2200 \, \text{J}\][/tex]

Therefore, the horse has a kinetic energy of 2200 Joules. Kinetic energy is a form of mechanical energy, which is associated with the motion of an object. As the horse moves, its kinetic energy represents the energy of its motion.

To learn more about kinetic energy refer:

https://brainly.com/question/25959744

#SPJ11

The electric field due to the point charge at the observation location is (-2.24 x 10⁵, -4.49 x 10⁵, -6.73 x 10⁵) N/C and force on the chlorine ion due to the electric field is (3.59 x 10⁻¹⁴, 7.18 x 10⁻¹⁴, 1.08 x 10⁻¹³) N.

In this problem, we are given a point charge and an observation location and asked to find the electric field and force due to the point charge at the observation location.

a. To find the electric field at the observation location due to the point charge, we can use Coulomb's law, which states that the electric field at a point in space due to a point charge is given by:

E = k*q/r² * r_hat

where k is the Coulomb constant (8.99 x 10⁹ N m²/C²), q is the charge, r is the distance from the point charge to the observation location, and r_hat is a unit vector in the direction from the point charge to the observation location.

Using the given values, we can calculate the electric field at the observation location as follows:

r = √((2-(-3))² + (7-5)² + (5-(-2))²) = √(98) m

r_hat = ((-3-2)/√(98), (5-7)/√(98), (-2-5)/√(98)) = (-1/7, -2/7, -3/7)

E = k*q/r² * r_hat = (8.99 x 10⁹N m^2/C²) * (22 x 10⁻⁶ C) / (98 m²) * (-1/7, -2/7, -3/7) = (-2.24 x 10⁵, -4.49 x 10⁵, -6.73 x 10⁵) N/C

Therefore, the electric field due to the point charge at the observation location is (-2.24 x 10⁵, -4.49 x 10⁵, -6.73 x 10⁵) N/C.

b. To find the force on the chlorine ion due to the electric field, we can use the equation:

F = q*E

where F is the force on the ion, q is the charge on the ion, and E is the electric field at the location of the ion.

Using the given values and the electric field found in part a, we can calculate the force on the ion as follows:

q = -1.6 x 10⁻¹⁹ C (charge on a singly charged chlorine ion)

E = (-2.24 x 10⁵, -4.49 x 10⁵, -6.73 x 10⁵) N/C

F = q*E = (-1.6 x 10⁻¹⁹ C) * (-2.24 x 10⁵, -4.49 x 10⁵, -6.73 x 10⁵) N/C = (3.59 x 10⁻¹⁴, 7.18 x 10⁻¹⁴, 1.08 x 10⁻¹³) N.

Learn more about force at: https://brainly.com/question/12785175

#SPJ11

We would need a radio telescope with a diameter of at least 114 meters to detect the signal from 70000 light-years away. Assuming the signal strength follows the inverse square law for light, we can use the following equation:

[tex]P1/P2 = (D2/D1)^2[/tex]

where

P1 is the power of the signal received by the Arecibo telescope,

P2 is the power of the signal we want to detect,

D1 is the distance from the Arecibo telescope to the source of the signal (105 light-years),

D2 is the distance from us to the source of the signal (70000 light-years).

We can rearrange the equation to solve for P2:

[tex]P2 = P1*(D1/D2)^2[/tex]

Plugging in the given values, we get:

[tex]P2 = 1.1*10^4 watts * (105/70000)^2[/tex]

    = 0.029 watts

So we need a radio telescope that can detect a signal with a power of 0.029 watts.

The Arecibo telescope has a diameter of 300 meters, so we can use the following equation to find the required diameter, D, of the telescope:

[tex]P = k*A*(D/2)^2[/tex]

where

P is the power of the signal that the telescope can detect,

A is the effective area of the telescope,

k is a constant (about 1 for radio telescopes), and

D is the diameter of the telescope.

We can rearrange the equation to solve for D:

[tex]D = \sqrt{(4*P/(k*A*\pi ))[/tex]

Plugging in the given values, we get:

[tex]D = \sqrt{(4*0.029/(1*(\pi )*(1.36*10^7)))[/tex]

   = 114 meters

Therefore, we would need a radio telescope with a diameter of at least 114 meters to detect the signal from 70000 light-years away.

To know more about Arecibo telescope refer here

brainly.com/question/18649585#

#SPJ11

The expression for the speed of the cart, after it travels a distance d, is v = √(2Fd cosθ/m), where F is the magnitude of the force exerted on the cart, θ is the angle below the horizontal at which the force is exerted, m is the total mass of the cart, and d is the distance traveled by the cart.

To determine the speed of the grocery cart after it travels a distance d, we can use the principle of work energy. The work done by the force F on the cart is given by:

W = Fd cosθ

Since the cart starts at rest, its initial kinetic energy is zero. The work done by the force F will be equal to the final kinetic energy of the cart:

W = (1/2)mv^2

where v is the final speed of the cart. Equating these two expressions, we get:

Fd cosθ = (1/2)mv²

Solving for v, we get:

v = √(2Fd cosθ/m)

It is assumed that there is no friction acting on the cart.

You can learn more about magnitude at: brainly.com/question/31022175

#SPJ11

The correct answer is b.

To determine the mass moment of inertia of a thin plate about an axis perpendicular to the page and passing through point O.

We can use the formula I = (1/12) * m * (a^2 + b^2), where I is the mass moment of inertia, m is the mass per unit area, and a and b are the dimensions of the plate.

Plugging in the given values, we get I = (1/12) * 20 * (0.17^2 + 0.45^2) = 0.738 kg-m^2.

Therefore, the correct answer is (b).

Learn more about Mass moment of inertia calculation.

brainly.com/question/31135787

#SPJ11

Simple harmonic motion is a type of motion where an object moves back and forth in a repeating pattern. It is like a pendulum swinging back and forth or a spring bouncing up and down.

For an object to exhibit simple harmonic motion, there are two conditions that must be met. The first is that there must be a restoring force that acts on the object.

This means that when the object is moved away from its resting position, there is a force that pulls or pushes it back towards that position. In the case of a pendulum, gravity provides the restoring force.

In the case of a spring, the elastic force of the spring provides the restoring force.

The second condition is that the restoring force must be proportional to the displacement of the object. This means that the further the object is moved away from its resting position, the greater the restoring force will be.

This results in the object oscillating back and forth in a predictable pattern.

So, in summary, simple harmonic motion is a type of motion where an object moves back and forth in a repeating pattern.

It occurs when there is a restoring force that acts on the object and that force is proportional to the displacement of the object.

To know more about harmonic motion refer here

https://brainly.com/question/30404816#

#SPJ11

(a) The mass flow rate of entering atmospheric air is approximately 76.7 kg/s. (b) The mass flow rate of makeup water is approximately 759.6 kg/s.

(a) Using the psychrometric chart, we can determine the specific humidity of the entering atmospheric air to be approximately 0.0133 kg/kg. The mass flow rate of air can be calculated as the ratio of the heat transfer rate to the product of the specific heat of air and the temperature difference between the entering and exiting air. Thus,

(b) Since the system is at steady state, the mass flow rate of makeup water must equal the mass flow rate of cooled water leaving the tower. Using the energy balance, we can calculate the heat transferred from the condenser to the cooling water and then equate it to the product of the mass flow rate of water, the specific heat of water, and the temperature difference between the entering and exiting water. Solving for the mass flow rate of makeup water, we get

To learn more about mass flow rate, here

https://brainly.com/question/13348162

#SPJ4

The third force that should be applied to keep the object in equilibrium is -3i - j.

To determine the third force, we need to find the negative sum of the two given forces. The given forces are represented by the vectors i - 2j + k and 2i + j - k. By adding these two vectors and negating the result, we obtain the third force required to balance the other two forces and maintain equilibrium.

The third force is obtained by adding the corresponding components of the vectors: 2i + 3j - 2k. This means that a force of magnitude 2 units in the positive x-direction, 3 units in the positive y-direction, and 2 units in the negative z-direction should be applied to keep the object in equilibrium.

Learn more about Equilibrium forces

brainly.com/question/12582625

#SPJ11

No, it violates the law of conservation of energy. The amount of electricity produced cannot exceed the amount of heat energy transferred.

The law of conservation of energy states that energy cannot be created or destroyed, only transferred or converted from one form to another. In this case, if we transfer 5 kWh of heat energy to an electric resistance wire, we can convert it into electrical energy, but the amount of electricity produced cannot exceed the amount of heat energy transferred. This is due to the efficiency of the conversion process. In reality, the amount of electricity produced would be less than 5 kWh, as some energy would be lost as heat due to resistance in the wire. Therefore, it is not possible to produce 6 kWh of electricity from 5 kWh of heat energy.

learn more about electricity here:

https://brainly.com/question/8971780

#SPJ11

Saturn's powerful magnetic field prevents ice boulders from growing, which is why its f ring remains so thin (narrow) while the other rings are so broad. Option c is Correct.

Because Prometheus and Pandora, two tiny moons, are guiding Saturn's F ring, it is slender. The shepherding pressures produced by these moons, which orbit close to the F ring, prevent the ring's particles from dispersing. The F ring is also wider and denser than Saturn's other rings, giving it the illusion of being narrower.  

A moon named Prometheus is located just inside the F ring, and a second (smaller) moon named Pandora is located just outside the F ring. These "shepherding" moons preserve the F ring at its constricted width due to their gravitational attraction. Option c is Correct.

Learn more about saturn's Visit: brainly.com/question/19508804

#SPJ4

(a) The speed of the wave is 5.0 m/s.

(b) The wavelength of the wave is 9.0 m.

(c) The frequency of the wave is 9.1 Hz.

(d) The power transmitted by the wave is 0.41 W.

To determine the speed of the wave, we need to use the equation v = λf, where v is the wave speed, λ is the wavelength, and f is the frequency. Since we are given the wave function, we can see that the coefficient of the x term is 0.70, which corresponds to 2π/λ. Solving for λ, we get λ = 9.0 m. The frequency is given by the coefficient of the t term, which is 57, so f = 57/(2π) ≈ 9.1 Hz. Therefore, the speed of the wave is v = λf ≈ 5.0 m/s.

As we found in part (a), the wavelength is given by λ = 2π/k, where k is the coefficient of the x term in the wave function. Substituting the given values, we get λ = 9.0 m.

As we found in part (a), the frequency is given by the coefficient of the t term in the wave function, which is 57/(2π) ≈ 9.1 Hz.

The power transmitted by a wave on a string is given by P = ½μv²ω²A², where μ is the mass per unit length, v is the wave speed, ω is the angular frequency (ω = 2πf), and A is the amplitude of the wave. Substituting the given values, we get P = 0.41 W.

To learn more about power transmitted, here

https://brainly.com/question/28964433

#SPJ4

(a) The angle of incidence is less than the critical angle, the light ray will refract into the air, and the angle of refraction will be less than the angle of incidence.(b) The angle of incidence is less than the critical angle, the light ray will refract into the liquid, and the angle of refraction will be greater than the angle of incidence.

Total internal reflection occurs when a light ray travelling from a denser medium towards a less dense medium reaches an angle of incidence greater than the critical angle. The critical angle is the minimum angle of incidence at which total internal reflection occurs. In this case, the critical angle for total internal reflection at a liquid-air interface is 42.5 degrees.
(a) If a ray of light travelling in the liquid has an angle of incidence at the interface of 35 degrees, the angle that the refracted ray in the air makes with the normal can be found using Snell's law. The formula for Snell's law is n1sinθ1 = n2sinθ2, where n1 and n2 are the refractive indices of the media, θ1 is the angle of incidence and θ2 is the angle of refraction. In this case, n1 is the refractive index of the liquid and n2 is the refractive index of air, which is approximately 1. The angle of incidence is 35 degrees, and we can calculate the angle of refraction as sinθ2 = (n1/n2)sinθ1 = (n1/1)sin35 = n1sin35. As the angle of incidence is less than the critical angle, the light ray will refract into the air, and the angle of refraction will be less than the angle of incidence.
(b) If a ray of light travelling in air has an angle of incidence at the interface of 35 degrees, the angle that the refracted ray in the liquid makes with the normal can also be found using Snell's law. The formula for Snell's law in this case is n1sinθ1 = n2sinθ2, where n1 is the refractive index of air, and n2 is the refractive index of the liquid. We can rearrange the formula to find the angle of refraction as sinθ2 = (n1/n2)sinθ1 = (1/n2)sin35. As the angle of incidence is less than the critical angle, the light ray will refract into the liquid, and the angle of refraction will be greater than the angle of incidence.

To know more about total internal reflection visit :

https://brainly.com/question/28231417

#SPJ11