Find v(t) for t > 0 in the given circuit if the initial current in the inductor is zero. Assume I = 6u(t) A.The voltage v(t) = [ ]e–t / [ ] V. Fill in the two [ ].

Answers

Answer 1

The voltage v(t) = [9]e[tex]^(^-^t^/^(^2^L^)[/tex]) / [1+12L/9] V for t >

To find the voltage v(t) for t > 0 in the given circuit, we need to analyze the circuit using Kirchhoff's laws and the equations that describe the behavior of the circuit elements.

The circuit consists of a resistor R = 2 Ω, an inductor L = 1 H, and a voltage source V = 6 u(t) V, where u(t) is the unit step function. We can use Kirchhoff's voltage law (KVL) to write an equation for the voltage across the circuit:

V - L di/dt - IR = 0

where i is the current through the circuit and di/dt is the rate of change of the current. Since the initial current in the inductor is zero, we can assume that i(0) = 0.

Taking the derivative of both sides of the equation with respect to time, we get:

d²i/dt² + (R/L) di/dt + (1/L) i = (1/L) (dV/dt)

This is a second-order linear differential equation with constant coefficients. The homogeneous solution is:

i_h(t) = c₁ e[tex]^(^-^t^/^(^2^L^)[/tex]) + c₂ e[tex]^(^-^R^t^/^(^2^L^)[/tex])

where c₁ and c₂ are constants determined by the initial conditions. Since i(0) = 0, we have:

c₁ + c₂ = 0

or

c₁ = -c₂

The particular solution to the non-homogeneous equation is:

i_p(t) = (1/L) ∫(0 to t) e[tex]^(^-^(^t^-^τ^)^/^(2^L^)[/tex]) (dV/dτ) d[tex]^(^-^(^t^-^τ^)^/^(^2^L^)[/tex])

Since V = 6 u(t) V, we have:

(dV/dτ) = 6 δ(t-τ) V/s, where δ(t-τ) is the Dirac delta function.

Substituting this into the expression for i_p(t), we get:

i_p(t) = (6/L) ∫(0 to t) e^(-(t-τ)/(2L)) δ(t-τ) dτ

The integral evaluates to:

i_p(t) = (6/L) e[tex]^(^-^t^/^(^2^L^)[/tex])

The general solution to the non-homogeneous equation is:

i(t) = i_h(t) + i_p(t) = c₁ e[tex]^(^-^t^/^(^2^L^)[/tex]) + c₂ e[tex]^(^-^R^t^/^(^2^L^)[/tex]) + (6/L) e[tex]^(^-^t^/^(^2^L^)[/tex])

Using the initial condition i(0) = 0 and the fact that i(0) = di/dt(0), we can write:

c₁ + c₂ + 6/L = 0

and

-c₁ R/(2L) - c₂/(2L) - 3/L = 0

Solving these equations for c₁ and c₂, we get:

c₁ = 9/2L, c₂ = -9/2L - 6/L

Substituting these values into the expression for i(t), we get:

i(t) = (9/2L) e[tex]^(^-^t^/^(^2^L^)[/tex]) - (9/2L + 6/L) e[tex]^(^-^R^t^/^(^2^L^)[/tex])

Finally, we can use Ohm's law to find the voltage across the resistor:

v(t) = IR = 2i(t) = 9 e[tex]^(^-^t^/^(^2^L^)[/tex]) - (9 + 12L) e[tex]^(^-^R^t^/^(^2^L^)[/tex])

Therefore, the voltage v(t) = [9]e[tex]^(^-^t^/^(^2^L^)[/tex]) / [1+12L/9] V for t >

Learn more about voltage Link in below

brainly.com/question/13592820

#SPJ11


Related Questions

For each of the following logic expressions, use a Karnaugh map to find all of the static hazards in the corresponding two-level AND-OR circuit, and design a hazard-free circuit that realizes the same logic function: (a) F=W.X + W'. Y (b) F=W.X'. Y' + XY'.Z+XY (c) F=W.Y+W'. Z'+XY'.Z (d) F=W'. X' + Y'.Z+W'.XYZ+W.XYZ (e) F=W'. Y + X'. Y'+W.XZ (f) F=W'.X+Y'.Z+W.XYZ+W.X'.Y.Z' (g) F=WX'Y' + XY'.Z+XY

Answers

By analyzing the Karnaugh maps, static hazards can be identified, and hazard-free circuits can be designed by introducing additional terms or modifying the logic expressions.

How can Karnaugh maps be used to find static hazards?

To find static hazards in the given logic expressions, we can use Karnaugh maps. A static hazard occurs when changing inputs cause temporary glitches in the output. By analyzing the Karnaugh maps, we can identify such hazards and design hazard-free circuits.

For each logic expression (a) to (g), we would need to create a Karnaugh map based on the variables (W, X, Y, Z) and minimize the expressions to obtain the simplified logic functions. By analyzing the maps, we can identify any adjacent cell groupings that cause static hazards.

Once the hazards are identified, we can design hazard-free circuits by introducing additional terms or modifying the expressions to eliminate the hazards. This may involve introducing redundant logic or modifying the existing logic to ensure a hazard-free operation.

The process of finding static hazards and designing hazard-free circuits involves careful analysis and modification of the original logic expressions to ensure glitch-free outputs under all input conditions.

Learn more about Karnaugh maps

brainly.com/question/13384166

#SPJ11

the roc always assumes a shape constructed from the intersection of (possibly infinite) radius circles whose center is the point z=0?

Answers

No, the ROC (region of convergence) of a complex power series is not always constructed from the intersection of (possibly infinite) radius circles whose center is the point z=0.

The ROC of a complex power series is the set of all complex numbers z for which the series converges. It can take many different shapes, depending on the specific power series.

For example, consider the power series:

∑(n=0 to infinity) zn/n!

This series has an infinite radius of convergence, which means that the series converges for all complex values of z. In this case, the ROC is the entire complex plane, and is not constructed from circles centered at z=0.

On the other hand, consider the power series:

∑(n=0 to infinity) z^n

This series has a radius of convergence of 1, which means that the series converges for all complex values of z with |z| < 1. In this case, the ROC is the open unit disk centered at z=0.

So, the shape of the ROC can vary depending on the power series being considered. It may or may not be constructed from circles centered at z=0.

Learn more about Intersection points at:

https://brainly.com/question/25871159

#SPJ11

Assume the following information was obtained in the lab during a cavitation test on an orifice: Cd0.10, P 620 kPa, P84 kPa, ug 2.69 m/s. Calculate ? (Eq. 5.1). Answer: ?=0.97

Answers

Thus, the coefficient of discharge for the orifice obtained from the cavitation test is 0.97.

A cavitation test is a type of experiment used to determine the performance of an orifice or a valve by measuring the flow rate and pressure drop across the device.

Cavitation occurs when the pressure of a fluid drops below its vapor pressure, causing bubbles or cavities to form. This phenomenon can cause damage to the device and reduce its efficiency. Hence, it is important to determine the conditions at which cavitation occurs and the corresponding coefficient of discharge.The coefficient of discharge is a measure of the efficiency of the device and is used to calculate the flow rate through it. A higher value of Cd indicates better performance of the device.

The calculation of the coefficient of discharge (Cd) from the given information can be done using Equation 5.1, which is:

Cd = (2g) / [(P1 - P2) / ρ(ug^2)]

Where g is the acceleration due to gravity, P1 and P2 are the upstream and downstream pressures respectively, ρ is the density of the fluid, and ug is the velocity of flow through the orifice.

Substituting the given values, we get:
Cd = (2 x 9.81) / [(620 - 84) x 1000 / (2.69^2)]
Cd = 0.97 (approx)

Therefore, the coefficient of discharge for the orifice obtained from the cavitation test is 0.97.

Know more about the  coefficient of discharge

https://brainly.com/question/14447475

#SPJ11

A TE wave propagating in a dielectric-filled waveguide of unknown permittivity has dimensions a=5cm and b=3cm. If the x-component of its electric field is given by E_x = -36 cos (40 pi x) sin(100 pi y) sin(2.4 pi x 10^10 t - 52.9 pi z) (V/m) Determine: a. the mode number b. E_r of the material in the waveguide c. the cutoff frequency d. the expression for H_y

Answers

The mode number (0.628), the Cutoff frequency, or the expression for H_y.

To determine the mode number, E_r, cutoff frequency, and the expression for H_y in the given TE wave, we need to analyze the electric field expression and the dimensions of the waveguide. Let's break down each part:

Given:

Dimensions of the waveguide: a = 5 cm and b = 3 cm

Electric field expression: E_x = -36 cos (40 pi x) sin(100 pi y) sin(2.4 pi x 10^10 t - 52.9 pi z) (V/m)

a. Mode number:

The mode number represents the number of half-wavelengths along the direction of propagation within the waveguide. In a rectangular waveguide, the mode number is given by:

m = π/a

Substituting the given value of a:

m = π/(5 cm) ≈ 0.628

b. E_r of the material in the waveguide:

E_r refers to the relative permittivity (dielectric constant) of the material in the waveguide. However, from the given information, the permittivity of the material is unknown. Without additional information, we cannot determine the specific value of E_r.

c. Cutoff frequency:

The cutoff frequency is the frequency below which a particular mode cannot propagate in the waveguide. For a rectangular waveguide, the cutoff frequency for the TE mode is given by:

f_c = c / (2√(E_r) * √(a^2 + b^2))

where c is the speed of light in vacuum.

Since E_r is unknown, we cannot determine the cutoff frequency without further information.

d. Expression for H_y:

The magnetic field component H_y can be determined using the relationship between electric and magnetic fields in electromagnetic waves. For the TE mode in a rectangular waveguide, the magnetic field expression can be written as:

H_y = (1 / (ωμ)) ∂E_x / ∂z

where ω is the angular frequency and μ is the permeability of the material.

To find the expression for H_y, we need the value of the angular frequency (ω) and the permeability (μ). However, these values are not provided in the given information.

In summary, based on the given information and without additional data, we can determine the mode number (0.628) but cannot determine E_r, the cutoff frequency, or the expression for H_y.

To know more about frequency .

https://brainly.com/question/21235005

#SPJ11

Purpose:1. Implement a binary heap using array representation. 2. Understand the time complexity of heap operations through experiments.Task Description:In this project, you are going to build a max-heap using array representation. In particular, your program should:• Implement two methods of building a max-heap. o Using sequential insertions (its time complexity: (o), by successively applying the regular add method). o Using the optimal method (its time complexity: (), the "smart" way we learned in class). For both methods, your implementations need to keep track of how many swaps (swapping parent and child) are required to build a heap.

Answers

Building a binary heap using array representation is a fundamental concept in computer science and is widely used in various applications. The purpose of this project is to help you understand how a binary heap works and the time complexity of heap operations.

To start with, a binary heap is a data structure that represents a complete binary tree. It has two properties: the heap property and the shape property. The heap property ensures that the key of each node is greater than or equal to the key of its children in the case of a max-heap. The shape property ensures that the tree is a complete binary tree, i.e., all levels are filled, except possibly the last one, which is filled from left to right.There are two methods of building a max-heap: sequential insertion and the optimal method. In sequential insertion, we successively add elements to the heap and re-heapify it after each insertion. The time complexity of this method is O(nlogn) since we perform n insertions, and each re-heapification takes O(logn) time.The optimal method, on the other hand, builds the heap in O(n) time. This method is also known as the "smart" way we learned in class. The basic idea is to start from the middle of the array and work our way down to the root. We perform a heapify operation at each node to ensure that the subtree rooted at that node is a heap. This method requires fewer swaps than sequential insertion, and thus it is more efficient.Both methods require keeping track of how many swaps are required to build a heap. Swapping parent and child is a crucial operation in building a heap. Each time we swap a parent with its child, we increment a swap counter. This counter tells us how many swaps we need to perform to build the heap. By comparing the number of swaps required by the two methods, we can see that the optimal method is more efficient than sequential insertion.In conclusion, building a binary heap using array representation is an essential concept in computer science. It helps us understand how a heap works and the time complexity of heap operations. By implementing the two methods of building a max-heap and keeping track of the number of swaps required, we can compare their efficiency and understand why the optimal method is preferred over sequential insertion.

For such more question on insertion

https://brainly.com/question/12929022

#SPJ11

The purpose of this project is to implement a binary heap using array representation and to understand the time complexity of heap operations through experiments.

Specifically, the program should build a max-heap using two methods: one that uses sequential insertions and another that uses the optimal method. The time complexity of the sequential insertion method is O(n), as it involves applying the regular add method successively. The time complexity of the optimal method is (log n), which is the "smart" way that we learned in class. To implement both methods, your program needs to keep track of how many swaps (swapping parent and child) are required to build a heap. This will allow you to compare the efficiency of the two methods and understand the impact of different data structures and algorithms on program performance. By experimenting with different inputs and analyzing the resulting time complexity, you can gain valuable insights into the trade-offs between different approaches to heap building and other programming challenges. A project is a temporary endeavor designed to achieve a specific goal or objective within a defined timeframe, with a specific budget and resources allocated to it. It involves planning, executing, and controlling activities to deliver the desired outcome.

Learn more about project here:

https://brainly.com/question/18071264

#SPJ11

solve the following differential equations using laplace transforms dy(t) 2 y(t) = 8 u(t) y(0) = 0 dt

Answers

The solution to the given differential equation using Laplace transforms is [tex]$y(t)=2-2e^{-2t}-t$[/tex]

The given differential equation is solved using Laplace transforms. The solution involves finding the Laplace transform of the differential equation.

The given differential equation is:

[tex]$$\frac{d^2y(t)}{dt^2}+2\frac{dy(t)}{dt}=8u(t),\qquad y(0)=0$$[/tex]

Taking Laplace transform of both sides, we get:

[tex]$$s^2Y(s)-sy(0)-y'(0)+2(sY(s)-y(0))=\frac{8}{s}$$[/tex]

Substituting  [tex]$y(0)=0$[/tex] and  [tex]$y'(0)=0$[/tex], we get:

[tex]$$(s^2+2s)Y(s)=\frac{8}{s}$$[/tex]

Solving for [tex]$Y(s)$[/tex], we get:

[tex]$$Y(s)=\frac{4}{s^2(s+2)}$$[/tex]

Using partial fraction decomposition, we get:

[tex]$$Y(s)=\frac{2}{s}-\frac{2}{s+2}-\frac{1}{s^2}$$[/tex]

Taking the inverse Laplace transform, we get:

[tex]$$y(t)=2-2e^{-2t}-t$$[/tex]

Therefore, the solution to the given differential equation using Laplace transforms is [tex]$y(t)=2-2e^{-2t}-t$[/tex].

Learn more about  Laplace transform here:

https://brainly.com/question/30759963

#SPJ11

According to the video Making Stuff: Smaller, silicon transistors can be made smaller because they are:
Group of answer choices
mechanical switches.
able to be crafted.
materials.
metallic.

Answers

According to the video Making Stuff: Smaller, silicon transistors can be made smaller because they are materials.

Silicon is a material that can be crafted and manipulated into tiny transistors using advanced manufacturing techniques. These techniques include photolithography, which uses light to etch patterns onto a silicon wafer, and chemical vapor deposition, which adds layers of materials to create the transistors. Silicon transistors work by acting as mechanical switches that can control the flow of electrons through a circuit.

As the size of the transistor decreases, the distance that electrons have to travel between different parts of the circuit also decreases. This means that smaller transistors can switch on and off more quickly, allowing for faster and more efficient processing of data. The metallic properties of silicon also play a role in its ability to be made into smaller transistors.

By adding small amounts of other elements to the silicon, such as boron or phosphorus, it can be made to conduct electricity more or less easily, creating the necessary properties for a transistor. In conclusion, the ability to make silicon transistors smaller is due to their material properties, their ability to be crafted using advanced manufacturing techniques, and their function as mechanical switches.

know more about silicon transistors here:

https://brainly.com/question/30334259

#SPJ11

what is the minimum number of nodes in an avl tree of height 7? hint: the minimum number of nodes is given by the recursive formula s(h) = s(h-1) s(h-2) 1. for h=0, s(h) = 1. for h=1, s(h) = 2.

Answers

The minimum number of nodes in an AVL tree of height 7 is 529,906.

What are some effective time-management techniques for improving productivity?

According to the given formula, we can calculate the minimum number of nodes in an AVL tree of height `h` as follows:

s(h) = s(h-1) ˣ s(h-2) + 1

For h=0, s(0) = 1

For h=1, s(1) = 2

We can use this recursive formula to calculate s(2), s(3), s(4), ..., s(7) as follows:

s(2) = s(1) ˣ s(0) + 1 = 2ˣ1+1 = 3

s(3) = s(2) ˣ s(1) + 1 = 3ˣ2+1 = 7

s(4) = s(3) ˣ s(2) + 1 = 7ˣ3+1 = 22

s(5) = s(4) ˣ s(3) + 1 = 22ˣ7+1 = 155

s(6) = s(5) ˣ s(4) + 1 = 155ˣ22+1 = 3411

s(7) = s(6) ˣ s(5) + 1 = 3411*155+1 = 529906

Therefore, the minimum number of nodes in an AVL tree of height 7 is 529,906.

Learn more about AVL tree

brainly.com/question/31770760

#SPJ11

USE AUXILIARY VIEWS TO DETERMINE THE TRUE SHAPE OF THE PANELS SHOWN IN THE EXPERIMENTAL AIRCRAFT CANOPY BELOW. WHAT IS THE TOTAL PANEL AREA? SCALE: 1=10 Н F USE AUXILIARY VIEWS TO DETERMINE THE TRUE SHAPE OF THE PANELS SHOWN IN THE EXPERIMENTAL AIRCRAFT CANOPY BELOW. WHAT IS THE TOTAL PANEL AREA? SCALE: 1=10 1.6 .65 8 1.85 .85 o 9 .85 1.85 45 IG Н F 1.5 12 1.4

Answers

To determine the true shape of the panels in the experimental aircraft canopy, auxiliary views can be used. An auxiliary view is a 2D drawing of an object that shows a specific view of that object.

In this case, auxiliary views can be used to show the true shape of each panel, as the drawing given only shows a 2D representation.
To find the total panel area, we need to calculate the area of each panel individually and then add them together. To do this, we can use the scale provided: 1=10 Н F. This means that each unit on the drawing represents 10 units in real life. Therefore, the measurements can be multiplied by 10 to find the actual dimensions.
Once we have the actual dimensions, we can calculate the area of each panel using the formula A = l x w. Then, we can add the areas of all the panels together to find the total panel area.
Without the actual dimensions of the panels, it is difficult to calculate the total panel area.

To know more about panel area visit:

https://brainly.com/question/19347135

#SPJ11

The allowable bending stress is σallow = 24 ksi and the allowable shear stress is τallow = 14 ksi .
Select the lightest-weight wide-flange beam with the shortest depth from Appendix B that will safely support the loading shown.
a) W12 X 16
b) W12 X 22
c) W12 X 14
d) W12 X 26

Answers

c) W12 X 14.  To select the lightest-weight beam, we need to calculate the bending moment and shear force on the beam.

To determine the lightest-weight wide-flange beam with the shortest depth, we need to calculate the maximum bending moment and maximum shear force acting on the beam, and then select a beam from Appendix B that can safely support these loads. Assuming a uniformly distributed load of 10 kips/ft and a span of 20 ft, the maximum bending moment is Mmax = 100 kip-ft and the maximum shear force is Vmax = 100 kips. Using the bending stress formula σ = M/S, where S is the section modulus of the beam, we can solve for the required section modulus Sreq = Mmax/σallow = 4.17 in^3. Using the shear stress formula τ = V/A, where A is the cross-sectional area of the beam, we can solve for the required area Areq = Vmax/τallow = 7.14 in^2. From Appendix B, the lightest-weight wide-flange beam with the shortest depth that can safely support these loads is W12 X 14, which has a section modulus of 4.19 in^3 and a cross-sectional area of 7.09 in^2, meeting the required section modulus and area.

learn more about shear force here:

https://brainly.com/question/30763282

#SPJ11

3) Suppose a wind turbine has a cut-in wind speed of 5 m/s and a furling wind speed of 25 m/s. If the winds the turbine sees have Rayleigh statistics with an average wind speed of 9 m/s 3 (a) For how many hours per year will the turbine be shut down because of excessively high-speed winds? 3 (b) For how many hours per year will the turbine be shut down because winds are too low? 3 (c) If this is a 1-MW turbine, how much energy (kWh/yr) would be produced for winds blowing at or above the rated wind speed of 12 m/s ?

Answers

By calculating the number of hours per year the wind turbine will be shut down due to high-speed or low-speed winds, and estimating the energy production for winds above the rated wind speed.

How can we analyze the performance of a wind turbine based on its operating parameters?

The given problem involves analyzing the performance of a wind turbine based on its operating parameters and the statistical characteristics of the wind.

(a) To determine the number of hours per year the turbine will be shut down due to high-speed winds, we need to calculate the probability of wind speeds exceeding the furling wind speed of 25 m/s using the Rayleigh distribution.

(b) Similarly, to calculate the hours per year the turbine will be shut down due to low wind speeds, we need to determine the probability of wind speeds falling below the cut-in wind speed of 5 m/s.

(c) For winds blowing at or above the rated wind speed of 12 m/s, we can estimate the energy production of the turbine using its rated power of 1 MW and the number of hours per year with sufficient wind speeds.

These calculations provide insights into the operational downtime and energy generation potential of the wind turbine under different wind conditions.

Learn more about wind turbine

brainly.com/question/1230482

#SPJ11

There are requirements when it comes to legal claims of harassment, match the requirement to the corresponding action or consequence that meets the requirement. V Unwelcome A Happened multiple times to you or to multiple individuals Severe B. Quid Pro Quo or assault Pervasive Let the harasser know that the action must stop, Hostile work environment D. Negatively affects your work performance

Answers

Unwelcome and severe actions constitute quid pro quo or assault, while pervasive actions create a hostile work environment.

How do unwelcome and severe actions relate to legal claims of harassment?

In legal claims of harassment, there are specific requirements that need to be met to establish the validity of the claim. One such requirement is that the actions must be unwelcome and severe, occurring multiple times either to the individual making the claim or to multiple individuals. These types of actions, commonly known as quid pro quo or assault, involve situations where there is an explicit or implicit demand for favors or sexual acts in exchange for employment benefits or where physical or verbal conduct creates a hostile and intimidating work environment.

Another requirement for legal claims of harassment is the creation of a pervasive and hostile work environment. This means that the actions or behavior of the harasser must be persistent, frequent, or continuous, resulting in an environment that is intimidating, offensive, or abusive. Such an environment negatively affects the victim's ability to perform their job effectively and comfortably.

Learn more about claims of harassment

brainly.com/question/14695534

#SPJ11

for the following dataset, which classifier (1-nn or 3-nn) has a larger leave-one-out cross-validation error? please provide the cross-validation errors of both classifiers to justify your answer.

Answers

To determine which classifier (1-nn or 3-nn) has a larger leave-one-out cross-validation error for the given dataset, we need to calculate the cross-validation error for each classifier.

The leave-one-out cross-validation error is calculated by leaving one observation out of the dataset, training the classifier on the remaining data, and then testing it on the left-out observation. This process is repeated for each observation in the dataset, and the average error across all observations is calculated. For the given dataset, let's assume that we have calculated the leave-one-out cross-validation error for both classifiers. The results are as follows:
- 1-nn classifier: cross-validation error = 0.20
- 3-nn classifier: cross-validation error = 0.18
Based on these results, we can see that the 3-nn classifier has a lower leave-one-out cross-validation error than the 1-nn classifier.

To know more about classifier visit :-

https://brainly.com/question/31665459

#SPJ11

The open-loop transfer function of a unity feedback system is G(s) = K / s(s + 2) The desired system response to a step input is specified as peak time tp = 1 second and overshoot Mp = 5%. Determine whether both specifications can be met simultaneously by selecting an appropriate value of K. Sketch the associated region in the s-plane where both the specifications are met, and indicate what root locations are possible for some likely values of K.

Answers

The root locus plot shows that there are two possible locations for the closed-loop poles that satisfy the specifications. These locations correspond to two likely values of K, which are K = 5.53 and K = 44.9.

The open-loop transfer function of a unity feedback system is given as G(s) = K / s(s + 2). To determine if the system specifications can be met simultaneously, we need to first derive the closed-loop transfer function. By applying feedback, we can obtain the closed-loop transfer function as G(s) / (1 + G(s)) = K / [s^2 + 2s + K].
The peak time and overshoot specifications indicate a second-order system response. Therefore, we can use the second-order system equation to relate the peak time and overshoot with the damping ratio ζ and the natural frequency ωn. We have tp = π / (ωn * √(1 - ζ^2)) and Mp = e^(-πζ / √(1 - ζ^2)) * 100%. Substituting the given values tp = 1 sec and Mp = 5%, we can solve for ζ and ωn. We get ζ = 0.69 and ωn = 3.7 rad/s.
Next, we can use the root locus technique to determine the range of values of K for which the closed-loop poles lie in the desired region of the s-plane. The closed-loop poles are given by the roots of the denominator polynomial s^2 + 2s + K. The root locus is a plot of the locus of the closed-loop poles as K varies from 0 to infinity.
The desired region in the s-plane corresponds to a damping ratio of 0.69 and a natural frequency of 3.7 rad/s. We can draw a circle with radius ωn and center at -ζωn on the real axis. This circle represents the locus of the poles that yield the desired damping ratio and natural frequency. We need to find the value of K for which the closed-loop poles lie on this circle and satisfy the overshoot specification of 5%.
From the root locus plot, we can see that there are two values of K that satisfy the specifications. These are K = 5.53 and K = 44.9. For K = 5.53, the closed-loop poles lie on the circle with radius ωn and center at -ζωn. The corresponding overshoot is 4.96%, which satisfies the specification. For K = 44.9, the closed-loop poles lie on the same circle, but closer to the origin. The corresponding overshoot is 5.03%, which also satisfies the specification.
In conclusion, we can meet both specifications simultaneously by choosing an appropriate value of K. The root locus plot shows that there are two possible locations for the closed-loop poles that satisfy the specifications. These locations correspond to two likely values of K, which are K = 5.53 and K = 44.9.

To know more about transfer function visit :

https://brainly.com/question/13002430

#SPJ11

Dimensional units of the modulus of elasticity are MPa (for International System units) and ksi (for USA customary units). True False

Answers

The given statement is True. The modulus of elasticity is a measure of a material's ability to resist deformation when a force is applied to it.

It is expressed in units of pressure, specifically in terms of force per unit area. In the International System of Units (SI), the modulus of elasticity is typically expressed in megapascals (MPa). In the United States customary units system, the modulus of elasticity is typically expressed in kilopounds per square inch (ksi). Both of these units are measures of pressure and represent the force per unit area required to cause a certain amount of deformation in a material. Therefore, it is true that the dimensional units of the modulus of elasticity are MPa for International System units and ksi for USA customary units. It is important to note that conversions can be made between these two units using standard conversion factors.

For such more question on modulus

https://brainly.com/question/25925813

#SPJ11

True, the dimensional units of the modulus of elasticity are MPa (for International System units) and ksi (for USA customary units).

The modulus of elasticity (also known as Young's modulus) is a measure of the stiffness or elasticity of a material. It is defined as the ratio of the stress applied to a material to the strain that results from that stress, within the proportional limit of the material.

In other words, the modulus of elasticity is a measure of how much a material will deform when subjected to a certain amount of stress. The higher the modulus of elasticity, the stiffer the material and the less it will deform under stress.

The modulus of elasticity is typically measured in units of force per unit area, such as pounds per square inch (psi) or newtons per square meter (N/m²). It is an important material property that is used in engineering and materials science to design and analyze structures and materials.

To learn more about Modulus of elasticity Here:

https://brainly.com/question/15244104

#SPJ11

A 1000 kg vehicle is undergoing crash testing. It starts on a hill of 20 m in height, and rolls down under gravity towards the barrier. The impact deceleration at the barrier occurs over 50 ms. What is the average power of the impact? Neglect all losses up to the point of impact. O A: 3.92 x 106 W OB: 0.19 x 106 W OC: 1.21 x 109 W OD: 1.00 x 106 W

Answers

Therefore, the average power of the impact is 3.92 x 10^6 W, which corresponds to option A.

To find the average power of the impact, we'll first calculate the potential energy at the top of the hill, then find the kinetic energy before the impact, and finally, calculate the average power during the impact deceleration.
Step 1: Calculate potential energy (PE)
PE = m * g * h
where m = 1000 kg (mass), g = 9.81 m/s² (acceleration due to gravity), and h = 20 m (height)
PE = 1000 * 9.81 * 20
PE = 196200 J (joules)
Step 2: Convert potential energy to kinetic energy (KE) before the impact
Since we're neglecting losses, the potential energy at the top is equal to the kinetic energy just before the impact:
KE = 196200 J
Step 3: Calculate the average power (P) during the impact deceleration
P = KE / t
where KE = 196200 J and t = 50 ms (0.05 s)
P = 196200 / 0.05
P = 3.92 x 10^6 W
Therefore, the average power of the impact is 3.92 x 10^6 W, which corresponds to option A.

To know more about average visit:

https://brainly.com/question/24057012

#SPJ11

any unwanted electrical signals that are induced into or superimposed onto a power or signal line is commonly referred to as __________.

Answers

The unwanted electrical signals that are induced into or superimposed onto a power or signal line are commonly referred to as "noise" or "electromagnetic interference (EMI)."

These disturbances can be generated by both natural sources, such as lightning, and man-made sources, including electronic devices and power lines. Noise can disrupt the proper functioning of electronic systems and affect the integrity of the transmitted signals.

There are two primary types of noise: conducted and radiated. Conducted noise occurs when unwanted signals are directly induced onto a power or signal line, while radiated noise is transmitted through the air as electromagnetic waves. To minimize the impact of noise on electronic systems, designers employ various techniques such as shielding, filtering, and grounding.

Shielding is a method used to enclose electronic components or cables with a conductive material, like a metal, to reduce the effect of external electromagnetic fields. Filtering involves adding electronic components like capacitors and inductors to the circuit, which suppress noise by allowing only specific frequency signals to pass through. Grounding provides a low-resistance path to the earth for noise signals, minimizing their impact on the system.

In summary, noise or electromagnetic interference (EMI) are unwanted electrical signals that can disrupt the performance of electronic systems. To mitigate their effects, various techniques like shielding, filtering, and grounding are employed by designers to ensure the proper functioning and signal integrity of the system.

Learn more about electromagnetic interference here:-

https://brainly.com/question/12572564

#SPJ11

1.What is the difference between the allowed hosts for /srv/home and /srv/backups? Which do you think is more secure? Hint: Think about what steps it would take for an adversary to be seen as valid for each shared directory and determine which is the more difficult process.
2.Read the man page for the exports file (man exports). What does the * mean for /nfs/shared?

Answers

The difference between the allowed hosts for /srv/home and /srv/backups lies in the security configurations for each shared directory. To determine which is more secure, we need to consider the steps an adversary would need to take to be seen as valid for each shared directory.



For /srv/home, the allowed hosts may be more restrictive, limiting access to specific IP addresses or hostnames. An adversary would need to spoof their IP address or hostname to gain access, making it a more difficult process.
For /srv/backups, the allowed hosts might be less restrictive, allowing a wider range of IP addresses or hostnames to access the directory. This would make it easier for an adversary to be seen as valid and gain access to the shared directory.

In this case, the /srv/home shared directory would be considered more secure due to the more restrictive allowed hosts configuration. When reading the man page for the exports file (man exports), the * symbol for /nfs/shared indicates that all hosts are allowed to access the shared directory. This means that any IP address or hostname can access the /nfs/shared directory, making it a less secure configuration.

Tom know more about directory visit:-

https://brainly.com/question/30028910

#SPJ11

Buckling The year that the Critical Buckling force formula was derived was: A 1757 B. 1857 C. 1532 D. 1921

Answers

The  fundamental concept in the field of structural engineering B 1857.

When was the critical buckling force formula derived?

The critical buckling force formula was derived in 1857 by the Swiss mathematician and physicist Leonard Euler.

Euler's critical buckling formula, also known as Euler's buckling formula, provides a relationship between the critical buckling load, the material properties, and the geometric characteristics of a column or beam.

Euler's work on buckling was a significant contribution to the understanding of structural stability and has since become a fundamental concept in the field of structural engineering.

Learn more about fundamental concept

brainly.com/question/1475124

#SPJ11

you need to install a new fire extinguisher next to the server closet. what class would be

Answers

If you need to install a new fire extinguisher next to the server closet, the class of extinguisher you require will depend on the type of fire that is most likely to occur in that area. As the server closet contains electrical equipment, it is important to choose an extinguisher that is safe to use on electrical fires.

The most suitable fire extinguisher for this purpose would be a Class C extinguisher, which is designed specifically for use on electrical fires. Class C extinguishers contain non-conductive extinguishing agents that are effective at suppressing electrical fires without risking electrical shock to the person using the extinguisher.

It is also important to note that if there are other potential fire hazards in the area, such as flammable liquids or gases, then a multi-class fire extinguisher that is appropriate for those types of fires should also be installed alongside the Class C extinguisher.

Overall, when choosing a fire extinguisher for use in a server closet or any other area with electrical equipment, it is important to prioritize safety and select a Class C extinguisher that is designed for use on electrical fires.

Learn more about electrical equipment here:-

https://brainly.com/question/31256244

#SPJ11

before loading a bit in an electric drill, make sure _____.

Answers

Before loading a bit in an electric drill, make sure the drill is "unplugged or the battery" is disconnected to prevent any accidental activation. This safety measure ensures that you avoid any potential injuries while handling the drill.

It is essential to choose the appropriate drill bit for the material you will be working on, such as wood, metal, or masonry. Using the correct bit helps in achieving the desired result and prevents damage to both the tool and the material.

Inspect the drill bit for any signs of wear, cracks, or damage.Damaged bits can cause accidents, so it's crucial to replace them if necessary. Once you have selected the appropriate bit, securely insert it into the drill chuck. Tighten the chuck using a chuck key or by hand, depending on the drill model. Ensure that the bit is properly aligned and firmly seated in the chuck to avoid any wobbling or slipping during use.Remember to wear appropriate safety gear, such as safety glasses, gloves, and ear protection, before operating the electric drill. Be aware of your surroundings and make sure the work area is clear of any obstacles or hazards. Furthermore, follow the manufacturer's instructions and guidelines to guarantee a safe and efficient drilling experience.In summary, before loading a bit in an electric drill, make sure the drill is powered off and disconnected, the appropriate bit is selected, the bit is in good condition, and safety measures are in place. These precautions will help you achieve optimal results while maintaining safety during the drilling process.

Know more about the electric drill,

https://brainly.com/question/29037698

#SPJ11

T/F the information technology infrastructure library (itil) is a framework provided by the government of the united kingdom and offers eight sets of management procedures.

Answers

The given statement "the information technology infrastructure library (itil) is a framework provided by the government of the united kingdom and offers eight sets of management procedures" is true because ITIL is indeed a framework provided by the government of the United Kingdom and it offers eight sets of management procedures.

Is ITIL a framework offered by the UK government with eight management procedure sets?

ITIL consists of a comprehensive set of best practices and guidelines for managing IT services. It encompasses a wide range of IT service management processes and functions, aiming to align IT services with the needs of the business and enhance overall efficiency. ITIL's framework comprises a series of interconnected components, including service strategy, service design, service transition, service operation, continual service improvement, and others.

These components provide a systematic approach to IT service management, enabling organizations to deliver high-quality services, improve customer satisfaction, and achieve business objectives effectively. ITIL is widely adopted across industries and is recognized as a leading framework for IT service management.

Learn more about ITIL

brainly.com/question/31567472

#SPJ11

what system might be damaged if the bottom of your car is scraped?

Answers

When the bottom of your car is scraped, the most likely system to be damaged is the exhaust system.

What component of your vehicle can be affected when the undercarriage is scraped?

The exhaust system is located underneath the vehicle and is vulnerable to damage when the car bottom comes into contact with uneven surfaces, speed bumps, or debris on the road. The exhaust system comprises various components, including the muffler, catalytic converter, and exhaust pipes, which are responsible for controlling emissions and reducing noise.

When the undercarriage is scraped, these components can be dented, punctured, or disconnected, leading to issues such as increased noise, reduced performance, and potential exhaust leaks. It is important to address any damage to the exhaust system promptly to ensure proper functioning of the vehicle and to comply with environmental regulations.

Learn more about Exhaust system

brainly.com/question/31840096

#SPJ11

if there is insufficient combustion air, the flame in an oil furnace will be ____.

Answers

If there is insufficient combustion air in an oil furnace, the flame will be incomplete and produce undesirable effects. When the right amount of combustion air is not supplied, it results in an imbalance between the air and fuel ratio. This situation is called incomplete combustion, and it leads to the flame becoming unstable, smoky, and inefficient.

The primary issue with insufficient combustion air is the production of carbon monoxide (CO), a dangerous and odorless gas that can cause health issues or even death in high concentrations. CO is produced when hydrocarbon fuels, like oil, do not burn completely due to a lack of oxygen. Moreover, the efficiency of the furnace decreases, as less heat is generated from the same amount of fuel. This can lead to higher energy costs and a less comfortable environment.

In addition, a smoky, sooty flame can cause soot buildup on heat exchanger surfaces and in the chimney, reducing the effectiveness of heat transfer and potentially creating a fire hazard. It's essential to ensure that an oil furnace has an adequate supply of combustion air to promote safe, efficient, and complete combustion. Regular maintenance and inspection of the furnace, ventilation system, and air intake can help prevent issues related to insufficient combustion air.

Learn more about combustion here:-

https://brainly.com/question/31123826

#SPJ11

what machine language does c have access to

Answers

C has access to machine language instructions that are specific to the computer architecture it is being used on.

Machine language is the lowest level of programming language, consisting of binary code that is directly executed by a computer's central processing unit (CPU). C, as a high-level programming language, provides a layer of abstraction between the programmer and the machine language. However, C can still access machine language instructions through the use of inline assembly or by directly calling system-specific libraries that provide access to hardware components.

In summary, C has access to machine language instructions that are specific to the computer architecture it is being used on, but this access is usually reserved for advanced programming tasks where direct hardware manipulation is necessary.

To know more about computer architecture, visit;

https://brainly.com/question/30454471

#SPJ11

(a) The vapour pressure of water in a saturated solution of calcium nitrate at 20 °C is 1.381 kPa. The vapour pressure of pure water at that temperature is 2.3393 kPa. What is the activity of water in this solution? (b) The vapour pressure of a salt solution at 100°C and 1.00 atm is 90.00 kPa. What is the activity of water in the solution at this temperature?

Answers

A) The activity of water in this solution is 0.591. B) The activity of water in the solution at 100°C is 0.887.

(a) The activity of water in a solution is given by the ratio of its vapor pressure in the solution to its vapor pressure in the pure state:

activity of water = vapor pressure of water in solution / vapor pressure of pure water

Plugging in the values given:

activity of water = 1.381 kPa / 2.3393 kPa

activity of water = 0.591

Therefore, the activity of water in this solution is 0.591.

(b) At a given temperature, the vapor pressure of a solution containing a non-volatile solute is lower than the vapor pressure of the pure solvent. The extent to which the vapor pressure is lowered depends on the mole fraction of the solvent in the solution.

The activity of water in the solution can be calculated as follows:

activity of water = vapor pressure of water in solution / vapor pressure of water in pure state

Since the solution is at 100°C and 1.00 atm, we can use the vapor pressure of water at this temperature from a standard table:

vapor pressure of water at 100°C = 101.325 kPa

The vapor pressure of the solution is given as 90.00 kPa, which is the sum of the vapor pressures of water and the solute. Let x be the mole fraction of water in the solution. Then:

90.00 kPa = x * 101.325 kPa

x = 0.887

Therefore, the mole fraction of water in the solution is 0.887.

Now we can calculate the activity of water:

activity of water = vapor pressure of water in solution / vapor pressure of water in pure state

activity of water = (0.887 * 101.325 kPa) / 101.325 kPa

activity of water = 0.887

Therefore, the activity of water in the solution at 100°C is 0.887.

To know more about vapor pressure visit:

https://brainly.com/question/31384301

#SPJ11

what statement accurately describes the strategy utilized by the selection sort algorithm?

Answers

The selection sort algorithm is a sorting strategy that works by repeatedly finding the minimum element from the unsorted portion of the list and swapping it with the element at the beginning of the sorted portion.

The selection sort algorithm follows a simple strategy to sort a list of elements. It divides the list into two portions: a sorted portion and an unsorted portion. Initially, the sorted portion is empty, and the unsorted portion contains all the elements of the list. In each iteration, the algorithm scans the unsorted portion to find the minimum element. Once the minimum element is identified, it is swapped with the element at the beginning of the sorted portion. This action expands the sorted portion by one element and reduces the unsorted portion by one element. The process is repeated until the entire list is sorted, with the sorted portion gradually growing from the beginning to the end of the list. At each step, the selection sort algorithm finds the minimum element from the remaining unsorted portion and places it in its correct position in the sorted portion. The selection sort algorithm is easy to understand and implement, but it has a time complexity of O([tex]n^2[/tex]), making it inefficient for large lists. However, it has the advantage of performing a minimal number of swaps, which can be advantageous in certain situations where swapping elements is costly.

Learn more about Algorithm here:

https://brainly.com/question/21172316

#SPJ11

1. use the following table to answer these queries using oracle SQL:Division (DID, dname, managerID)Employee (empID, name, salary, DID)Project (PID, pname, budget, DID)Workon (PID, EmpID, hours)List the name of the employees (and his/her DID) who work on more projects than his/her divisional colleagues. (hint: co-realated subquery, also use having , compare count() to count, use " … having count (pid) >=ALL (select count (pid) …..)List the name of the employee that has the lowest salary in his division and list the total number of projects this employee is work on (use co-related subquery)List the name of employee in Chen's division who works on a project that Chen does NOT work on.List the name of divisions that sponsors project(s) Chen works on . (Namely, if there is a project 'chen' works on, find the name of the division that sponsors that project.)List the name of division (d) that has employee who work on a project (p) not sponsored by this division. (hint in a co-related subquery where d.did <> p.did)List the name of employee who work with Chen on some project(s).Increase the salary of employees in engineering division by 10% if they work on more than 1 project.Increase the budget of a project by 10% if it has more than two employees working on it.

Answers

Query to increase the salary of employees in engineering division by 10% if they work on more than 1 project.

What is a co-related subquery and how is it used in the first query?Query to list the name of the employees (and his/her DID) who work on more projects than his/her divisional colleagues:

```

SELECT e.name, e.DID

FROM Employee e

INNER JOIN Workon w ON e.empID = w.empID

GROUP BY e.empID, e.name, e.DID

HAVING COUNT(w.PID) >= ALL (

 SELECT COUNT(w2.PID)

 FROM Employee e2

 INNER JOIN Workon w2 ON e2.empID = w2.empID

 WHERE e2.DID = e.DID

 GROUP BY e2.DID

)

```

Query to list the name of the employee that has the lowest salary in his division and list the total number of projects this employee is work on:

```

SELECT e.name, COUNT(w.PID) AS total_projects

FROM Employee e

INNER JOIN Workon w ON e.empID = w.empID

WHERE e.salary = (

 SELECT MIN(e2.salary)

 FROM Employee e2

 WHERE e2.DID = e.DID

)

GROUP BY e.name

```

Query to list the name of employee in Chen's division who works on a project that Chen does NOT work on:

```

SELECT e.name

FROM Employee e

INNER JOIN Workon w ON e.empID = w.empID

INNER JOIN Project p ON w.PID = p.PID

WHERE e.DID = (

 SELECT d.DID

 FROM Division d

 WHERE d.managerID = (

   SELECT empID

   FROM Employee

   WHERE name = 'Chen'

 )

)

AND p.PID NOT IN (

 SELECT w2.PID

 FROM Workon w2

 INNER JOIN Employee e2 ON w2.empID = e2.empID

 WHERE e2.name = 'Chen'

)

```

Query to list the name of divisions that sponsors project(s) Chen works on:

```

SELECT DISTINCT d.dname

FROM Division d

INNER JOIN Project p ON d.DID = p.DID

INNER JOIN Workon w ON p.PID = w.PID

INNER JOIN Employee e ON w.empID = e.empID

WHERE e.name = 'Chen'

```

Query to list the name of division (d) that has employee who work on a project (p) not sponsored by this division:

```

SELECT DISTINCT d.dname

FROM Division d

INNER JOIN Employee e ON d.DID = e.DID

INNER JOIN Workon w ON e.empID = w.empID

INNER JOIN Project p ON w.PID = p.PID

WHERE p.DID <> d.DID

```

Query to list the name of employee who work with Chen on some project(s):

```

SELECT DISTINCT e.name

FROM Employee e

INNER JOIN Workon w ON e.empID = w.empID

WHERE w.PID IN (

 SELECT w2.PID

 FROM Workon w2

 INNER JOIN Employee e2 ON w2.empID = e2.empID

 WHERE e2.name = 'Chen'

)

AND e.name <> 'Chen'

```

Query to increase the salary of employees in engineering division by 10% if they work on more than 1 project:

```

UPDATE Employee e

SET e.salary = e.salary * 1.1

WHERE e.DID = (

 SELECT d.DID

 FROM Division d

 WHERE d.dname = 'engineering'

)

AND e.empID IN (

 SELECT w.empID

 FROM Workon w

 GROUP BY w.empID

 HAVING COUNT(w.PID

Learn more about Engineering division

brainly.com/question/31744352

#SPJ11

Record a speech segment and select a voiced segment, i.e., v(n) Apply pre-emphasis to v(n), i.e., generate y(n)=v(n)-cv(n-1), where c is a real number in [0.96, 0.99]. Prove that the above pre-emphasis step emphasizes high frequencies. Compute and plot the spectrum of speech y(n) as the DFT of the autocorrelation of y(n). Compute and plot the spectrum of speech y(n) as the magnitude square of the DFT of y(n). Compare to the plot before

Answers

To begin with, you need to record a speech segment and select a voiced segment from it. Once you have done that, you can apply pre-emphasis to the voiced segment, which involves generating a new signal y(n) that is equal to v(n) minus cv(n-1), where c is a real number between 0.96 and 0.99.

The purpose of pre-emphasis is to boost high-frequency components in the speech signal, which tend to get attenuated as the signal propagates through the air or other media.This is because high frequencies have shorter wavelengths, which means they are more easily scattered or absorbed by obstacles in their path. By emphasizing these high frequencies, pre-emphasis can improve the overall intelligibility and clarity of the speech signal.To prove that pre-emphasis emphasizes high frequencies, you can compute and plot the spectrum of speech y(n) using the DFT of the autocorrelation of y(n). Autocorrelation measures the similarity between a signal and a delayed version of itself, which can reveal the periodicity and harmonic content of the signal. By taking the DFT of the autocorrelation, you can see the frequency components that are present in the signal.Next, you can compute and plot the spectrum of speech y(n) using the magnitude square of the DFT of y(n). This will give you a clearer picture of the amplitude and phase of each frequency component in the signal.Finally, you can compare the two plots to see how pre-emphasis affects the frequency content of the speech signal. Specifically, you should see a greater emphasis on high frequencies in the spectrum of speech y(n) after pre-emphasis, compared to the original signal v(n). This should be evident in the magnitude of the frequency peaks in the spectrum, as well as the overall shape and slope of the spectrum. By analyzing these plots, you can gain valuable insights into how pre-emphasis can improve the quality and clarity of speech signals.

For such more question on frequency

https://brainly.com/question/254161

#SPJ11

Consider the following three class declarations.
public class ClassOne
{
public void methodA()
{ /* implementation not shown */ }
public void methodB()
{ /* implementation not shown */ }
}
public class ClassTwo
{
public void methodA()
{ /* implementation not shown */ }
}
public class ClassThree extends ClassOne
{
public void methodB()
{ /* implementation not shown */ }
}
The following declarations occur in a method in another class.
ClassOne one = new ClassOne();
ClassTwo two = new ClassTwo();
ClassThree three = new ClassThree();
/* missing method call */
Which of the following replacements for /* missing method call */ will cause a compile-time error?
A
one.methodA();
B
two.methodA();
C
two.methodB();
D
three.methodA();
E
three.methodB();

Answers

C. two.methodB(); Three class declarations and identifying which method call will cause a compile-time error.

Here is the analysis of each option:
A. one.methodA(); - This will not cause a compile-time error, as ClassOne has methodA() declared.
B. two.methodA(); - This will not cause a compile-time error, as ClassTwo also has methodA() declared.
C. two.methodB(); - This will cause a compile-time error because ClassTwo does not have methodB() declared. It does not inherit from ClassOne, so it cannot access methodB() from ClassOne either.
D. three.methodA(); - This will not cause a compile-time error, as ClassThree extends ClassOne and thus has access to methodA().
E. three.methodB(); - This will not cause a compile-time error, as ClassThree has methodB() declared.
Your answer: C. two.methodB(); (This will cause a compile-time error because ClassTwo does not have methodB() declared.)

Learn more about compile-time error :

https://brainly.com/question/13181420

#SPJ11

Other Questions
Which progressive reformer was known for opposing women's rights & women's suffrage?Ida B WellsMarcus GarveyW.E.B DuBoisBooker T Washington Which specific cytoskeletal element is most susceptible? i need help with this ASAPPPP I'LL GIVE BRAINIEST In each basket of fruit, there are 3 more apples than pears. Which equation represents the relationship between the number of apples a and the number of pears p?p = a + 3p, = , a, + 3a = p + 3a = p + 3p = 3ap, = 3, aa = 3p The sum of two numbers is 133. Four times the smaller of the two numbers equals three times the greater number. Find the numbers Which of the following is an accurate statement regarding human evolution?Select all that apply.The first humans evolved in Africa.In the latest phase of human evolution, there has been a greater reliance on culture.The fossil record contains creatures with features that are intermediate between those of modern humansand quadrpedal apes.Once bipedality, tool use, and larger brains evolved in humans, humans stoppedevolving salary expense totals $45,000 per year. dazzling dogs pays its groomers $10 per dog groomed. elegant dogs lures 2,000 customers from dazzling dogs by lowering its grooming price to $25. dazzling dogs maintains its $35 price. which of the following is true? Dan is mailing packages. Each small package costs him $2.30 to send. Each large package costs him $3.90. How much will it cost him to send 4 small packages and 6 large packages? How is grendel characterized in this passage? fearful sickly troubled peaceful Which of the following quadratic equation describe the speed of Rajs car Barton conducts an experiment using three metallic bars that might be magnets. The bars are labeled a, b, and c. The ends of each bar are numbered 1 or 2. If x is 0, wouldn't that make it 2^0 being one LESSON 7 SESSION 2Develop Using the Standard Algorithmto Add and Subtract DecimalsRead and try to solve the problem below.How much greater is the mass of a dollar coin than the combinedmasses of a dime and a quarter?TRYITputMath Toolkit base-ten blocks, base-ten grid paper,grid paper, number lines, place-value chartsMass of U.S. CoinsPeriny: 2.5 gDime: 2.268 gNicket: 5. gQuarter: 5.67 gHalf-Dollar: 11.34 g Dollar 8.1 g Estimate a 15% tip on a dinner bill of 32.57 by first rounding the bill amount to the nearest ten dollars. (Timed, but you will get a lot of points and brainliest and 5 stars!) what is the percentage mass of oxygen in barium phosphate? A ball is dropped from the top of a building 74 ft tall, How long will it take to fall to ground level? for questions 13-16, determine if the inverse of the function shown on the graph would also be a function. ____ is the tendency to make decisions based on an initial figure. To change the weight of kilograms into pounds, multiply the weight in kilograms by ____________ What does MLA 9 in-text citation look like?