help me please .
i need to submit the homework today .

Help Me Please .i Need To Submit The Homework Today .

Answers

Answer 1

Answer:

D. 0.010 m

Explanation:

wavelength [tex]\lambda[/tex] =[tex]570 nm = 570 nm * (1 m / 10^9 nm) = 5.7 * 10^{-7}m[/tex]

width(d)=[tex]0.0900 mm * (1 m / 1000 mm) = 9.00 * 10^{-5} m[/tex]

distance(L)=0.800 m

The width of the central bright band is given by the equation:

[tex]w = \frac{2\lambda L}{d}[/tex]

where [tex]$\lambda$[/tex] is the wavelength of light,[tex]$L$[/tex] is the distance from the slit to the screen, and [tex]$d$[/tex] is the width of the slit.

Substituting the given values, we get:

[tex]w = \frac{2(5.70 \times 10^{-7} \text{ m})(0.800 \text{ m})}{9.00 \times 10^{-5} \text{ m}} = 0.010 \text{ m}[/tex]

Therefore, the width of the central bright band is[tex]\boxed{0.010 \text{ m}}[/tex]


Related Questions

A series RLC circuit has R = 20 kΩ, L = 0.2 mH, and C = 5 μF. What type of damping is exhibited by the circuit?

Answers

In order to determine the type of damping exhibited by the series RLC circuit, we need to look at the values of R, L, and C and calculate the circuit's damping ratio,

which is defined as the ratio of the circuit's damping coefficient to its natural frequency.



The damping ratio (ζ) can be calculated using the following formula:



ζ = R / (2√(L/C))

Plugging in the values given in the question, we get:



ζ = 20,000 / (2√(0.2 x 10^-3 / 5 x 10^-6))


ζ = 20,000 / 2√40


ζ = 20,000 / (2 x 6.324)


ζ = 1578.3

Since the damping ratio (ζ) is greater than 1, the circuit exhibits over-damping. This means that the circuit's response is critically damped, which is characterized by a slow decay without oscillations.

The circuit's output will return to zero after a long time without any overshoot.



In conclusion, the series RLC circuit with R = 20 kΩ, L = 0.2 mH, and C = 5 μF exhibits over-damping, which results in critically damped behavior without any oscillations or overshoot.

To know more about circuit's damping ratio refer here

https://brainly.com/question/29490032#

#SPJ11

an electron is accelerated through a potential v. if the electron reached a speed of 9.11 x10 6 m/s, what is v?

Answers

To calculate the potential (v) through which an electron has been accelerated to reach a speed of 9.11 x 10^6 m/s, we can use the equation for the kinetic energy of the electron:

KE = 1/2mv^2

Where KE is the kinetic energy of the electron, m is the mass of the electron (9.11 x 10^-31 kg), and v is the speed of the electron.

Since the electron is accelerated through a potential, it gains potential energy (PE) which is then converted into kinetic energy as it accelerates. The potential energy gained by the electron is equal to the potential difference (v) multiplied by the charge of the electron (e = 1.6 x 10^-19 C):

PE = eV

Setting the initial potential energy of the electron equal to its final kinetic energy:

eV = 1/2mv^2

Solving for v:

v = sqrt(2eV/m)

Substituting the given values:

v = sqrt(2 x 1.6 x 10^-19 x v / 9.11 x 10^-31)

v = sqrt(3.2 x 10^-12 x v)

v = 1.79 x 10^6 sqrt(v) m/s

To find the value of v that would result in a speed of 9.11 x 10^6 m/s:

9.11 x 10^6 = 1.79 x 10^6 sqrt(v)

Solving for v:

v = (9.11 x 10^6 / 1.79 x 10^6)^2

v = 25 V

Therefore, the potential through which the electron has been accelerated is 25 volts.


learn more about  potential https://brainly.in/question/54060299?referrer=searchResults


#SPJ11

how much energy is required (in kj) when 22.0 g of ammonia is decomposed into its elements? the reaction requires 46 kj per mole of ammonia decomposed.

Answers

The total energy required to decompose 1.29 mol of NH₃ is 59.52 kJ.

What is the energy required?

The energy is required to decompose 22.0 g of NH₃ is calculated as follows;

Molar mass of NH₃ = 17 g/mol

The number of moles of 22 g of NH₃ is calculated as follows;

Number of moles of NH₃ = 22.0 g / 17 g/mol

= 1.294 mol

The total energy required to decompose 1.29 mol of NH₃ is calculated as;

Energy = 1.294 mol x 46 kJ/mol

Energy = 59.52 kJ

Learn more about energy here: https://brainly.com/question/25959744

#SPJ4

5. would it be possible to cool a real gas down to zero volume? why or why not? what do you think would happen before the volume was reached?

Answers

It is not possible to cool a real gas down to zero volume without undergoing a phase change.

No, it would not be possible to cool a real gas down to zero volume. This is because as we cool down a gas, its volume decreases, but it can never reach zero. According to the laws of thermodynamics, as we decrease the temperature of a gas, it also loses energy, which results in a decrease in its volume. However, as we approach zero temperature, the gas molecules would start to behave differently and begin to stick together. This would result in the formation of a liquid or solid state.
Before the volume of the gas reaches zero, we would expect a phase change to occur. At very low temperatures, the gas molecules would lose their kinetic energy and start to move slower. As a result, they would stick together, forming clusters of molecules. These clusters would eventually become larger, forming a liquid or a solid. This process is called condensation and it occurs when a gas is cooled down below its dew point temperature. Therefore, it is not possible to cool a real gas down to zero volume without undergoing a phase change.

To know more about Volume visit:

https://brainly.com/question/23865754

#SPJ11

a motor attached to a 120 v/60 hz power line draws an 8.00 a current. its average energy dissipation is 840 w.a)What is the power factor?b)What is the rms resistor voltage?c)What is the motor's resistance?d)How much series capacitance needs to be added to increase the power factor to 1?

Answers

To solve this problem, we'll use the following formulas:

(a) Power factor (PF) is given by the ratio of the real power (P) to the apparent power (S). Mathematically, it can be expressed as:

PF = P / S

(b) The RMS voltage (V) is related to the peak voltage (Vp) by the formula:

V = Vp / √2

(c) The resistance (R) of the motor can be determined using Ohm's law:

R = V / I

(d) To calculate the required series capacitance, we'll use the formula:

C = (tan φ) / (2πfR)

where φ is the angle of the power factor and f is the frequency.

Given:

Voltage (V) = 120 V

Current (I) = 8.00 A

Power (P) = 840 W

Frequency (f) = 60 Hz

(a) Power Factor (PF):

PF = P / S

The apparent power (S) can be calculated using the formula:

S = V * I

S = 120 V * 8.00 A

S = 960 VA

Now we can calculate the power factor:

PF = 840 W / 960 VA

PF ≈ 0.875

Therefore, the power factor is approximately 0.875.

(b) RMS Resistor Voltage (V):

V = Vp / √2

Vp is the peak voltage, which is the same as the RMS voltage.

V = 120 V / √2

V ≈ 84.85 V

Therefore, the RMS resistor voltage is approximately 84.85 V.

(c) Motor Resistance (R):

R = V / I

R = 120 V / 8.00 A

R = 15 Ω

Therefore, the motor's resistance is 15 Ω.

(d) Series Capacitance (C) to increase the power factor to 1:

To calculate the required series capacitance, we need to determine the angle φ.

φ = arccos(PF)

φ = arccos(0.875)

φ ≈ 29.68 degrees

Now we can calculate the required series capacitance:

C = (tan φ) / (2πfR)

C = tan(29.68 degrees) / (2π * 60 Hz * 15 Ω)

C ≈ 7.66 × 10^(-6) F

Therefore, approximately 7.66 microfarads (µF) of series capacitance needs to be added to increase the power factor to 1.

To know more about Power factor (PF) refer here

https://brainly.com/question/6346707#

#SPJ11

as shown in the figure, the charge q is midway between two other charges. if what must be the charge q1 so that charge q2 remains stationary as q and q1 are held in place?

Answers

To keep charge q2 stationary while charges q and q1 are held in place, the charge q1 must be equal in magnitude but opposite in sign to charge q.

What is the Coulomb's law?

According to Coulomb's law, like charges repel each other, and unlike charges attract each other. In the given scenario, to keep charge q2 stationary, the net force acting on it should be zero.

Let's assume charge q has a positive magnitude, represented as +q. To balance the forces and keep q2 stationary, the charge q1 should have the same magnitude but opposite sign, represented as -q.

Due to the equal magnitudes and opposite signs, the forces between q2 and q1 will cancel out, resulting in a net force of zero on q2. Meanwhile, the forces between q and q1 will still be repulsive, but since q is held in place, it won't affect the equilibrium of q2.

Therefore, by setting the charge q1 to -q, with the same magnitude as charge q but opposite sign, we can ensure that charge q2 remains stationary while charges q and q1 are held in place.

To know more about Coulomb's law, refer here:

https://brainly.com/question/506926#

#SPJ4

what happens to the potential difference between points 1 and 2 when the switch is closed?

Answers

The potential difference between points 1 and 2 decreases when the switch is closed.

What happens to the potential difference between points 1 and 2 when the switch is closed?

When the switch is closed, the potential difference between points 1 and 2 will decrease. This is because closing the switch creates a conducting path between the two points, allowing current to flow. As current flows, there will be a voltage drop across the resistance of the conducting path.

This voltage drop reduces the potential difference between points 1 and 2. The amount of decrease depends on the resistance of the conducting path and the amount of current flowing through it. In an ideal scenario with zero resistance in the switch and conducting path, the potential difference between points 1 and 2 would become zero.

However, in practical situations, there will still be a small potential difference due to the resistance of the conducting elements.

Learn more about potential difference

brainly.com/question/23716417

#SPJ11

A nuclear excited state decays by an E2 transition to the ^ ground state. List the possible spin-parity (I") assignments of the excited state. If there is no evidence of decay by an M1 transition, what is the I of the excited state most likely to be?

Answers

The I of the excited state is most likely to be 2+, since this is the lowest possible spin that satisfies the conditions we've discussed. However, it's important to note that other spin-parity assignments are still possible, depending on the specific details of the decay process.

When a nuclear excited state decays by an E2 transition to the ground state, there are certain rules that determine the possible spin-parity assignments of the excited state.

First, we need to know that the E2 transition involves a change in both spin and parity. Specifically, the spin changes by 2 units (delta I = 2), and the parity changes by (-1)^I, where I is the spin of the excited state.

So, let's say the ground state has a spin of I=0. In this case, the parity of the excited state must be opposite to that of the ground state, since (-1)^I = (-1)^0 = +1. Therefore, the possible spin-parity assignments of the excited state are I=2+, I=4+, I=6+, etc.

Now, let's consider the second part of the question. If there is no evidence of decay by an M1 transition, then we know that the spin of the excited state must be greater than 1. This is because M1 transitions only involve a change in spin by 1 unit (delta I = 1), so if there were no M1 transition observed, then the spin must have changed by 2 or more units.

To know more about excited state visit:-

https://brainly.com/question/15413578

#SPJ11

The machine has a mass m and is uniformly supported by four springs, each having a stiffness k.
Determine the natural period of vertical vibration(Figure 1)
Express your answer in terms of some or all of the variables m, k, and constant πpi.

Answers

Hi! To determine the natural period of vertical vibration for the machine supported by four springs, we can use the formula for the natural frequency (ωn) and then convert it to the natural period (T). The formula for the natural frequency of a mass-spring system is:

ωn = √(k_eq/m)

where k_eq is the equivalent stiffness of the four springs combined. Since the springs are arranged in parallel, the equivalent stiffness is the sum of their individual stiffness values:

k_eq = 4k

Now, substitute the equivalent stiffness back into the natural frequency formula:

ωn = √((4k)/m)

To find the natural period (T), we can use the relationship:

T = 2π/ωn

Substituting the value of ωn:

T = 2π / √((4k)/m)

So, the natural period of vertical vibration in terms of the variables m, k, and the constant π is:

T = 2π√(m/(4k))

learn more about vibration

https://brainly.in/question/2328401?referrer=searchResults

#SPJ11

An astronaut travels to a star system 4.7 ly away at a speed of 0.90 c . Assume that the time needed to accelerate and decelerate is negligible.A) How long does the journey take according to Mission Control on Earth? in yearsB) How long does the journey take according to the astronaut? in yearsC) How much time elapses between the launch and the arrival of the first radio message from the astronaut saying that she has arrived? in years

Answers

According to Mission Control on Earth, the journey takes 5.22 years. according to the astronaut, the journey takes 2.76 years. it will take 9.92 years from the launch for the first radio message to arrive on Earth.

A) t = t0 / √(1 - v²/c²)

Where t0 is the proper time (time experienced by the astronaut), v is the velocity (0.9c in this case), c is the speed of light, and t is the time according to Mission Control.

Plugging in the numbers, we get:

t = 4.7 ly / (0.9c) = 5.22 years

B). t0 = t / √(1 - v²/c²) = 5.22 years / √(1 - 0.9²) = 2.76 years

C). Since the speed of light is the fastest possible speed, the radio signal will take 4.7 years to travel to Earth.

So the total time elapsed is:

[tex]t_total[/tex] = t + 4.7 years = 5.22 years + 4.7 years = 9.92 years

An astronaut is a professional who is trained to travel in space, conduct experiments, repair equipment, and perform spacewalks outside of a spacecraft. They are highly skilled and have to undergo extensive training in various fields such as physics, engineering, astronomy, and medicine to prepare for their missions. The role of an astronaut involves operating complex systems and technologies, communicating with mission control on Earth, and conducting scientific experiments to learn more about the universe.

Astronauts work as part of a team and must be able to function effectively in the isolated and confined environments of a spacecraft. They must also be able to cope with the physical and psychological stresses associated with long-duration spaceflight. In addition to their technical skills, astronauts must have excellent physical fitness, mental toughness, and the ability to work well under pressure.

To learn more about Astronaut visit here:

brainly.com/question/29585275

#SPJ4

Assuming a star with a radius of 1×106 km has a planet with a radius of 3×105 km. The original observed radiance from the star by a telescope is 1 W/m2. What is the observed star’s radiance by the telescope with a transit event?(A) 0.91 W/m2 (B) 0.93 W/m2 (C) 0.95 W/m2 (D) 0.97 W/m2

Answers

The observed star’s radiance by the telescope with a transit event is (A) 0.91 W/m2.The observed radiance of a star can be affected by the transit of a planet. During the transit event, the planet passes in front of the star, blocking a portion of its light from reaching the observer on Earth.

How to calculate the observed star's radiance?

The ratio of the areas of the planet and the star can be calculated as:

(area of planet) / (area of star) = (πr^2) / (πR^2) where r is the radius of the planet and R is the radius of the star.

Substituting the given values, we get:

(area of planet) / (area of star) = (π(3x10^5)^2) / (π(1x10^6)^2) = 0.09

This means that the planet blocks 9% of the light from the star. The observed radiance of the star during the transit event can be calculated as:

observed radiance = (original observed radiance) x (1 - blocked fraction)

where the blocked fraction is the fraction of light blocked by the planet, which is 0.09 in this case. Substituting the values, we get:

observed radiance = (1 W/m^2) x (1 - 0.09) = 0.91 W/m^2

Therefore, the observed star's radiance by the telescope with a transit event is approximately 0.91 W/m^2. Hence the answer is (A) 0.91 W/m2.

Learn more about observed radiance

https://brainly.com/question/32182715

#SPJ11

a series rlc circuit attached to a 120 v/60 hz power line draws 2.40 a of current with a power factor of 0.900. What is the value of the resistor?

Answers

The value of the resistor in a series RLC circuit attached to a 120 V/60 Hz power line, with a current draw of 2.40 A and a power factor of 0.900, is R = 50 Ω.

we can use the formula:

Power factor = (R/Z)

where R is the resistance of the circuit, and Z is the impedance of the circuit. Impedance can be calculated as:

Z = sqrt(R^2 + (Xl - Xc)²)

where Xl is the inductive reactance of the circuit, and Xc is the capacitive reactance of the circuit.

We know that the power factor is 0.900, so we can rearrange the formula to solve for R:

R = Power factor x Z

To find Z, we need to calculate the inductive and capacitive reactances. The inductive reactance can be calculated as:

Xl = 2πfL

where f is the frequency (60 Hz), and L is the inductance of the circuit. The capacitive reactance can be calculated as:

Xc = 1/(2πfC)

where C is the capacitance of the circuit.

Since we do not have values for L or C, we cannot calculate Xl or Xc. However, we can assume that the circuit is either primarily inductive or primarily capacitive, based on the power factor.

A power factor of 0.900 indicates that the circuit is slightly inductive. Therefore, we can assume that Xl > Xc.

Assuming that the circuit is primarily inductive, we can use the formula for inductive reactance to estimate a value for L:

Xl = 2πfL

L = Xl/(2πf)

L = (120 Ω)/(2π x 60 Hz)

L = 318.31 mH

Using this value for L, we can calculate Xl:

Xl = 2πfL

Xl = 2π x 60 Hz x 318.31 mH

Xl = 120 Ω

Now we can calculate Z:

Z = sqrt(R^2 + (Xl - Xc)²)

Z = sqrt(R^2 + (120 Ω - Xc)²)

Since Xl > Xc, we know that Z > 120 Ω.

We also know that the current draw is 2.40 A. We can use Ohm's law to calculate the total impedance:

V = IR

120 V = 2.40 A x R

R = 50 Ω

Now we can use the formula for power factor to solve for Xc:

Power factor = (R/Z)

0.900 = (50 Ω)/(Z)

Z = (50 Ω)/(0.900)

Z = 55.56 Ω

We can now calculate Xc:

Z = sqrt(R^2 + (120 Ω - Xc)²)

55.56 Ω = sqrt(50^2 + (120 Ω - Xc)²)

Solving for Xc:

Xc = 67.37 Ω

Therefore, the value of the resistor in the circuit is:

R = 50 Ω.

To learn more about resistors visit: https://brainly.com/question/24858512

#SPJ11

A nearsighted person has near and far points of 11.1 and 19.0 cm , respectively. If she puts on contact lenses with power P = -3.00 D , what are her new near and far points?

Answers

Her new near and far points are 17.0 cm and 34.5 cm respectively.

The formula for calculating the new near and far points is:

1/f = 1/di + 1/do

where f is the focal length of the contact lenses, di is the distance between the contact lenses and the eye (which we can assume is negligible), and do is the distance of the object from the contact lenses.

The near and far points of the nearsighted person are:

dnear = 11.1 cm

dfar = 19.0 cm

To find the new near point, we plug in the values:

1/-3.00 = 1/dnear + 1/25.0

Solving for dnear, we get:

dnear = 17.0 cm

Therefore, the new near point with contact lenses is 17.0 cm.

To find the new far point, we plug in the values:

1/-3.00 = 1/dfar + 1/25.0

Solving for dfar, we get:

dfar = 34.5 cm

Therefore, the new far point with contact lenses is 34.5 cm.

For more questions on contact lenses:

https://brainly.com/question/10921004

#SPJ11

To find the new near and far points of the nearsighted person with contact lenses of power P = -3.00 D, we can use the following formula:

1/f = 1/di + 1/do

where f is the focal length of the lenses, di is the distance between the lenses and the eye, and do is the distance between the lenses and the object being viewed.

First, we need to find the focal length of the lenses:

P = 1/f

-3.00 D = 1/f

f = -1/3.00 m = -0.33 m

Now we can use the formula to find the new near and far points:

For the near point:

1/-0.33 = 1/0.111 + 1/do

-3.03 m = 9.01 m + 1/do

-12.04 m = 1/do

do = -0.083 m = -8.3 cm

Therefore, the new near point with contact lenses is 8.3 cm.

For the far point:

1/-0.33 = 1/0.190 + 1/do

-3.03 m = 5.26 m + 1/do

-8.29 m = 1/do

do = -0.121 m = -12.1 cm

Therefore, the new far point with contact lenses is 12.1 cm.

To learn more about focal length : brainly.com/question/29870264

#SPJ11

about half of the gas and dust that fills interstellar space is concentrated in dense regions called? quizle

Answers

About half of the gas and dust that fills interstellar space is concentrated in dense regions called molecular clouds.

Define the molecular clouds are regions within interstellar space?

Interstellar space is not completely empty but contains gas and dust spread throughout. Molecular clouds are regions within interstellar space where the gas and dust are highly concentrated. These clouds are composed mainly of molecular hydrogen (H₂) along with other molecules like carbon monoxide (CO) and various organic compounds.

Molecular clouds are dense and cold regions that serve as the birthplaces of stars. Within these clouds, gravity causes the gas and dust to clump together, forming denser regions known as molecular cloud cores. These cores can further collapse under their own gravity, leading to the formation of protostars and ultimately stellar systems.

The presence of dense molecular clouds is crucial for the process of star formation and the evolution of galaxies. They provide the necessary raw materials from which new stars and planetary systems can emerge, making them important objects of study in astronomy and astrophysics.

Therefore, approximately 50% of the gas and dust in interstellar space is found in concentrated areas known as molecular clouds, which play a vital role in star formation and galactic evolution

To know more about molecular clouds, refer here:

https://brainly.com/question/31023294#

#SPJ4

how fast must a meterstick be moving if its length is measured to shrink to 0.585 m?

Answers

the meterstick must be moving at a speed of about 0.822 times the speed of light, or approximately

This question is related to the concept of length contraction, which is a prediction of Einstein's theory of relativity. According to this theory, an object that is moving relative to an observer will appear shorter in the direction of its motion. The degree of length contraction depends on the speed of the object relative to the observer and is given by the formula: L' = L * sqrt(1 - v^2/c^2)

where L is the original length of the object, v is its speed relative to the observer, c is the speed of light, and L' is the observed length. If we plug in the values given in the question (L = 1 m and L' = 0.585 m), we can solve for v: 0.585 m = 1 m * sqrt(1 - v^2/c^2) Simplifying this equation, we get: v^2/c^2 = 1 - (0.585/1)^2 v^2/c^2 = 0.6765 v/c = sqrt(0.6765) v = 0.822c

To know more about speed visit:

https://brainly.com/question/28224010

#SPJ11

two capacitors are connected parallel to each otherr. let c1 = 2.70 μf, c2 = 5.20 μf, and vab = 60.0 v.,the potential difference across the system.Part A calculate the potential difference across each capacitorpart B calculate the charge on each capacitor

Answers

The potential difference across each capacitor in a parallel circuit is the same and equal to the total potential difference across the system. Therefore, the potential difference across each capacitor in this circuit is also 60.0 V.

Part B:
The charge on a capacitor is given by the formula Q = CV, where Q is the charge, C is the capacitance, and V is the potential difference across the capacitor.

Using this formula, we can calculate the charge on each capacitor:

For C1:
Q1 = C1 x Vab
Q1 = 2.70 μF x 60.0 V
Q1 = 162.0 μC

For C2:
Q2 = C2 x Vab
Q2 = 5.20 μF x 60.0 V
Q2 = 312.0 μC

Therefore, the charge on capacitor C1 is 162.0 μC, and the charge on capacitor C2 is 312.0 μC.


Part A:
When two capacitors are connected in parallel, the potential difference (voltage) across each capacitor remains the same as the potential difference across the system. Therefore,

V_C1 = V_C2 = V_AB = 60.0 V

Part B:
To calculate the charge on each capacitor, use the formula Q = C * V.

For capacitor C1:
Q_C1 = C1 * V_C1 = (2.70 μF) * (60.0 V) = 162.0 μC (microcoulombs)

For capacitor C2:
Q_C2 = C2 * V_C2 = (5.20 μF) * (60.0 V) = 312.0 μC (microcoulombs)

To know about Capicitor visit:

https://brainly.com/question/31431670

#SPJ11

the photons of green light have a wavelength of 550nm. i) determine the momentum of a green photon. ii) determine the energy of a green photon

Answers

i) The momentum of a green photon with a wavelength of 550 nm is approximately 1.13 x 10^-27 kg m/s.
ii) The energy of a green photon with a wavelength of 550 nm is approximately 3.61 x 10^-19 Joules.

The momentum of a green photon with a wavelength of 550nm can be determined using the formula p=hf/c, where p is the momentum, h is Planck's constant, f is the frequency, and c is the speed of light. Since we know the wavelength, we can calculate the frequency using the formula f=c/λ. Thus, f=c/550nm=5.45×10^14 Hz. Substituting this value in the formula for momentum, we get p=(6.63×10^-34 J s)(5.45×10^14 Hz)/3×10^8 m/s=1.13×10^-27 kg m/s.

The energy of a green photon with a wavelength of 550nm can be determined using the formula E=hf, where E is the energy. Using the frequency we calculated earlier, we can determine the energy as E=(6.63×10^-34 J s)(5.45×10^14 Hz)=3.61×10^-19 J. This is the energy of a single photon. In terms of electron volts (eV), this energy is approximately 2.25 eV. This energy is high enough to cause electrons in a material to be excited, leading to various phenomena such as the photoelectric effect, fluorescence, and absorption.

To know more about momentum, click here;

https://brainly.com/question/30677308

#SPJ11


Using Coulomb's Law, determine the distance in meters between two charges given that the force between the charges is 13,500,000 N and the values of the charges are Q1=-0.5C and Q2--0.3C. : k = 9,000,000,000 Nm2/C2. Your answer should have 3 significant figures such as 20.1 or 52.7 or 81.0. Please just enter a number. It is assumed your answer will be in meters.

Answers

The distance between two charges is  603,742 meters

Coulomb's Law states that the force of attraction or repulsion between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. In this case, the force between the two charges is given as 13,500,000 N, and the values of the charges are Q1 = -0.5C and Q2 = -0.3C. The value of k, which is the proportionality constant, is 9,000,000,000 Nm2/C2.

To determine the distance between the two charges, we can rearrange Coulomb's Law as:

distance = sqrt((force * k) / (charge1 * charge2))

Substituting the given values, we get:

distance = sqrt((13,500,000 * 9,000,000,000) / (0.5 * 0.3))

distance = sqrt(364,500,000,000) = 603,742.25 meters

Therefore, the distance between the two charges is approximately 603,742 meters, rounded to 3 significant figures.

In summary, Coulomb's Law is a useful tool for calculating the distance between two charges based on their respective magnitudes and the force between them. By understanding the relationship between these variables, we can better understand the fundamental forces that govern the behavior of electrically charged particles.

Know more about Coulomb's Law here:

https://brainly.com/question/506926

#SPJ11

T/F. The energy for n = 4 and f = 2 state is greater than the energy for n = 5 and l = 0 state.

Answers

The statement "The energy for n = 4 and f = 2 state is greater than the energy for n = 5 and l = 0 state" is true. The energy of an electron in a hydrogen atom is determined by its principal quantum number (n) and its orbital angular momentum quantum number (l), as well as its magnetic quantum number (m).

The energy level increases with increasing n, and within each energy level, the energy increases with increasing l. Thus, for the hydrogen atom, the energy of the n=5 and l=0 state (which is the 5s state) is lower than the energy of the n=4 and l=2 state (which is the 4d state).

This is because the 5s state has a lower value of l than the 4d state, and therefore experiences a weaker Coulombic attraction to the nucleus, resulting in a lower energy.

To know more about the quantum number refer here :

https://brainly.com/question/16746749#

#SPJ11

1. A 70kg skydiver lies out with a frontal area of 0.5m2, Cd = 0.9, r = 1.2 kg/m3. What is their terminal velocity during free-fall? Answer in MPH, 1609m = 1 mile, 3600 sec = 1 hour.​
2. If 60kg Roberto can ride his 8 kg bicycle up a 10% incline at 3 m/sec, how fast could he ride on level ground? Cd = 0.9, A = 0.3m2; ignore rolling resistance.​

Answers

Terminal velocity of skydiver = 174 mph

Roberto can ride at approximately 9.1 m/s on level ground.

To find the terminal velocity of the skydiver, we can use the formula Vt = sqrt((2mg)/(CdrA)), where m is the mass of the skydiver, g is the acceleration due to gravity, Cd is the drag coefficient, r is the density of air, and A is the frontal area of the skydiver. Plugging in the given values, we get Vt = sqrt((2709.81)/(0.91.20.5)) = 174 mph.

On the incline, the force acting against Roberto is the sum of the force of gravity and the force of air resistance, given by Fnet = mgsin(theta) - 0.5CdrAv^2, where theta is the angle of the incline, v is the velocity of Roberto, and all other variables have their usual meanings.

At 3 m/s, this net force allows him to ride up the incline. On level ground, we can ignore the force of gravity and set Fnet = 0, so we have 0 = - 0.5CdrAv^2, which gives us v = sqrt((2mg)/(CdrA)). Plugging in the given values, we get v = sqrt((2609.81)/(0.91.20.3)) = 9.1 m/s.

For more questions like Force click the link below:

https://brainly.com/question/13191643

#SPJ11

Consider a small silicon crystal measuring 100 nm on each side. (a) Compute the total number N of silicon atoms in the crystal. (The density of silicon is 2.33 g/cm3) (b) If the conduction band in silicon is 13 eV wide and recalling that there are 4N states in this band, compute an approximate value for the energy spacing between adjacent conduction band states for the crystal.

Answers

Answer:

(a) There are approximately 5 billion silicon atoms in the crystal.

(b) The energy spacing between adjacent conduction band states in the silicon crystal is approximately 6.54 × 10^(-11) eV.

Explanation:

(a) The volume of the silicon crystal is (100 nm)^3 = 1 × 10^6 nm^3 = 1 × 10^(-15) m^3. The mass of silicon in the crystal can be found by multiplying the volume by the density of silicon:

mass = volume × density = (1 × 10^(-15) m^3) × (2.33 g/cm^3) × (100 cm/m)^3 = 2.33 × 10^(-12) g

The molar mass of silicon is 28.086 g/mol, so the number of moles of silicon in the crystal is:

moles = mass / molar mass = 2.33 × 10^(-12) g / 28.086 g/mol = 8.30 × 10^(-14) mol

Finally, the total number of silicon atoms in the crystal can be found by multiplying the number of moles by Avogadro's number:

N = moles × Avogadro's number = (8.30 × 10^(-14) mol) × (6.022 × 10^23 /mol) = 4.99 × 10^9 atoms

Therefore, there are approximately 5 billion silicon atoms in the crystal.

(b) The energy spacing between adjacent conduction band states can be found by dividing the width of the conduction band by the number of states in the band:

energy spacing = 13 eV / 4N

Substituting the value of N found in part (a), we get:

energy spacing = 13 eV / (4 × 4.99 × 10^9) ≈ 6.54 × 10^(-11) eV

Therefore, the energy spacing between adjacent conduction band states in the silicon crystal is approximately 6.54 × 10^(-11) eV.

Learn more about "energy":

https://brainly.com/question/13881533

#SPJ11

A 0.50 μf capacitor is charged to 70 v. it is then connected in series with a 25 ω resistor and a 110 ω resistor and allowed to discharge completely.

Answers

The time it takes for the capacitor to fully discharge is about 5 times the time constant (5RC), or 337.5 μs.

When the 0.50 μF capacitor is charged to 70 V, it stores electrical energy in its electric field. However, when it is connected in series with a 25 ω resistor and a 110 ω resistor, the capacitor starts to discharge through the resistors. The time constant of the circuit (RC) is given by the product of the resistance and capacitance, which is 0.5 μF x (25 + 110) ω = 67.5 μs.

As the capacitor discharges, the voltage across it decreases exponentially according to the formula V(t) = V0 * e^(-t/RC), where V(t) is the voltage across the capacitor at time t, V0 is the initial voltage (in this case 70 V), and e is the mathematical constant. When t = RC, the voltage across the capacitor has decreased to about 37% of its initial value, or 25.9 V.

Eventually, the capacitor will fully discharge, meaning that the voltage across it will be 0 V. At this point, all of the energy that was stored in the capacitor has been dissipated through the resistors in the form of heat. The time it takes for the capacitor to fully discharge is about 5 times the time constant (5RC), or 337.5 μs in this case.

Learn more about resistors here,

https://brainly.com/question/30611906

#SPJ11

the 52-kg flywheel has a radius of gyration k⎯⎯ = 0.46 m about its shaft axis and is subjected to the torque m = 1.7(1 - e-0.12θ) where θ is in radians. if the flywheel is at rest

Answers

The final angular velocity of the flywheel after it has rotated through a certain angle θ can be given by ω = sqrt(2(1.7/10.0768)(1 - e^-0.12θ)θ).

The given information describes a flywheel with a mass of 52 kg and a radius of gyration of 0.46 m about its shaft axis. The torque applied to the flywheel is given by the function m = 1.7(1 - e^-0.12θ), where θ is in radians.

If the flywheel is at rest, then its initial angular velocity is zero. To find the angular acceleration of the flywheel, we can use the formula:

m = Iα

where m is the torque, I is the moment of inertia, and α is the angular acceleration.

The moment of inertia of a flywheel can be calculated using the formula:

I = mk²

where k is the radius of gyration.

Substituting the given values, we get:

I = (52 kg)(0.46 m)² = 10.0768 kg m²

Now, we can rewrite the torque equation as:

α = m/I = (1.7/I)(1 - e^-0.12θ)

Substituting the moment of inertia, we get:

α = (1.7/10.0768)(1 - e^-0.12θ)

This equation gives us the angular acceleration of the flywheel at any given angle θ. If we want to find the final angular velocity of the flywheel after it has rotated through a certain angle, we can use the formula:

ω² - ω0² = 2αθ

where ω is the final angular velocity, ω0 is the initial angular velocity (which is zero in this case), α is the angular acceleration, and θ is the angle rotated through.

Solving for ω, we get:

ω = sqrt(2αθ)

Substituting the expression for α, we get:

ω = sqrt(2(1.7/10.0768)(1 - e^-0.12θ)θ)

This equation gives us the final angular velocity of the flywheel after it has rotated through a certain angle θ.

More on angular velocity: https://brainly.com/question/31495959

#SPJ11

A sheep on a skateboard is standing still when she is pushed with a force of 59 n to the right for 1.5 seconds. if the sheep has a mass of 41 kg how fast will the sheep move?

please help!

Answers

A sheep on a skateboard is standing still when she is pushed with a force of 59 n to the right for 1.5 seconds. if the sheep has a mass of 41 kg  a speed of approximately 2.16 m/s after being pushed with a force of 59 N for 1.5 seconds.

To determine the speed at which the sheep will move, we can use Newton's second law of motion, which states that the acceleration of an object is directly proportional to the net force applied to it and inversely proportional to its mass.

The formula to calculate acceleration is given by:

Acceleration (a) = Net Force (F_net) / Mass (m)

In this case, the net force acting on the sheep is 59 N to the right, and the mass of the sheep is 41 kg.

Using the formula, we can calculate the acceleration:

a = 59 N / 41 kg ≈ 1.44 m/s^2

Now, we can use the formula for calculating the final velocity (v) of an object in uniform acceleration:

v = u + a * t

Given that the sheep was initially at rest (u = 0) and the time (t) is 1.5 seconds, we can substitute the values:

v = 0 + 1.44 m/s^2 * 1.5 s

v ≈ 2.16 m/s

Therefore, the sheep will move at a speed of approximately 2.16 m/s after being pushed with a force of 59 N for 1.5 seconds.

Learn more about Newton's second law of motion here:

https://brainly.com/question/27712854

#SPJ11

was PSE6 30.AE.03. [3660484] Question Details 2 Example 30.3 Magnetic Field on the Axis of a Circular Current Loop Problem Consider a circular loop of wire of radius R located in the yz plane and carrying a steady current I as in Figure 30.6. Calculate the magnetic field at an axial point P a distance x from the center of the loop. Strategy In this situation, note that any element as is perpendicular to f. Thus, for any element, ld5* xf| (ds)(1)sin 90° = ds. Furthermore, all length elements around the loop are at the same distancer from P, where r2 = x2 + R2. = Figure 30.6 The geometry for calculating the magnetic field at a point P lying on the axis of a current loop. By symmetry, the total field is along this axis,

Answers

The magnetic field at an axial point P a distance x from the center of a circular current loop of radius R carrying a steady current I is given by the expression B = (μ0IR2)/(2(r2)^(3/2)), where r2 = x2 + R2.

To calculate the magnetic field at a point P on the axis of a circular current loop, we first need to determine the distance between the point P and the loop. Using the Pythagorean theorem, we can find that distance, which is given by r2 = x2 + R2.

Next, we use the Biot-Savart law to calculate the magnetic field at point P due to a small element of the loop. Since the element is perpendicular to the vector from the element to point P, the angle between them is 90 degrees, and sin(90) = 1.

We can simplify the expression and integrate over the entire loop to find the total magnetic field at point P. By symmetry, the magnetic field is along the axis of the loop. The resulting expression for the magnetic field is B = (μ0IR2)/(2(r2)^(3/2)), where μ0 is the permeability of free space, I is the current in the loop, R is the radius of the loop, and r2 is the distance between the point P and the center of the loop.

Why is a series circuit current the same in a capacitor resistor and inductor while voltage is different?

Answers

In a series circuit, the current remains the same throughout the circuit due to the conservation of charge. However, the voltage across each component can vary depending on the component's impedance.

In the case of a resistor, the voltage drop across it is proportional to the current flowing through it according to Ohm's law. In an inductor, the voltage drop across it is proportional to the rate of change of current flowing through it due to its inductance. Similarly, in a capacitor, the voltage across it is proportional to the charge stored on it due to its capacitance. So, even though the current remains constant, the voltage across each component can vary depending on its impedance.

Learn more about voltage here:

https://brainly.com/question/13521443

#SPJ11

Superkid, finally fed up with Superbully\'s obnoxious behaviour, hurls a 1.07-kg stone at him at 0.583 of the speed of light. How much kinetic energy do Superkid\'s super arm muscles give the stone?
Give answer in joules

Answers

The stone has a kinetic energy of roughly 8.56 × 10¹⁷ joules thanks to Superkid's strong arm muscles.

We can use the formula for relativistic kinetic energy to calculate the kinetic energy of the stone:

K = (γ - 1) * m * c²

where γ is the Lorentz factor, m is the mass of the stone, c is the speed of light, and K is the kinetic energy.

The Lorentz factor can be calculated as:

γ = 1 / √(1 - v²/c²)

where v is the velocity of the stone relative to an observer at rest.

Substituting the given values, we have:

v = 0.583c

m = 1.07 kg

c = 299,792,458 m/s

So, γ = 1 / √(1 - (0.583c)²/c²) = 1.44

Substituting this value into the equation for kinetic energy, we get:

K = (γ - 1) * m * c² = (1.44 - 1) * 1.07 kg * (299,792,458 m/s)² = 8.56 × 10¹⁷ J

Therefore, Superkid's super arm muscles give the stone a kinetic energy of approximately 8.56 × 10¹⁷ joules.

Learn more about kinetic energy on:

https://brainly.com/question/16983571

#SPJ11

What is the wavelength of a photon that has a momentum of 5.00×10−29 kg ⋅ m/s ? (b) Find its energy in eV.

Answers

1.325 × [tex]10^-5[/tex] m is the wavelength of a photon that has a momentum of 5.00×[tex]10^-^2^9[/tex] kg and Energy of photon is 0.0936 eV.

The momentum of a photon is related to its wavelength λ by the equation:

p = h/λ

where p is the momentum, λ is the wavelength, and h is Planck's constant.

(a) Solving for λ, we have:

λ = h/p

Substituting the given values, we get:

λ = (6.626 × [tex]10^-^3^4[/tex]J s) / (5.00 × [tex]10^-^2^9[/tex] kg · m/s)

λ = 1.325 ×[tex]10^-^5[/tex]m

Therefore, the wavelength of the photon is 1.325 × [tex]10^-^5[/tex]m.

(b) The energy of a photon is related to its frequency f by the equation:

E = hf

where E is the energy and f is the frequency.

We can relate frequency to wavelength using the speed of light c:

c = λf

Solving for f, we get:

f = c/λ

Substituting the given wavelength, we get:

f = (2.998 × [tex]10^8[/tex]m/s) / (1.325 × [tex]10^-^5[/tex]m)

f = 2.263 × [tex]10^1^3[/tex] Hz

Now we can calculate the energy of the photon using the equation:

E = hf

Substituting the given values for Planck's constant and frequency, we get:

E = (6.626 × [tex]10^-^3^4[/tex]J s) × (2.263 × 1[tex]0^1^3[/tex]Hz)

E = 1.50 × 1[tex]0^-^2^0[/tex] J

Finally, we can convert this energy to electron volts (eV) using the conversion factor:

1 eV = 1.602 ×[tex]10^-^1^9[/tex]J

Therefore:

E = (1.50 ×[tex]10^-^2^0[/tex] J) / (1.602 × [tex]10^-^1^9[/tex] J/eV)

E = 0.0936 eV

So, the energy of the photon is 0.0936 eV.

To know more about Wavelength refer here :

https://brainly.com/question/30092711

#SPJ11

Suppose you were not held together by electromagnetic forces. How long would it take you to grow 3 centimeters because of the expansion of the universe? [HINT: Apply Hubble's Law to your head as seen by your feet. Calculate the velocity in cm/sec between your feet and head, using v=Hd, where H is the Hubble "constant", and d is your height. With this "expansion" or "growth" velocity, figure out how long it will take you to grow an additional 3 cm. [ANOTHER HINT: Take care with units!]

Answers

If not held together by electromagnetic forces, it would take approximately 2.52 x 10¹³ seconds for a person to grow 3 centimeters because of the expansion of the universe.

Hubble's Law describes the expansion of the universe, which states that the further away a galaxy is from us, the faster it is receding from us. The Hubble "constant" (H) is the proportionality factor between the recessional velocity of a galaxy and its distance from us.

Assuming a person's height is 170 cm and H is approximately 70 km/s/Mpc (the latest estimated value), we can calculate the velocity between a person's head and feet due to the expansion of the universe using v=Hd, where d is the person's height.

Therefore, v = 70 km/s/Mpc x 1.7 m =1.19 x 10⁻¹⁸ km/s.

We can convert this velocity to centimeters per second by multiplying it by 10⁵, giving us 1.19 x 10⁻¹³ cm/s. To grow 3 centimeters, a person would need to travel at this velocity for 3/1.19 x 10⁻¹³ = 2.52 x 10¹³ seconds.

To know more about velocity, refer here:

https://brainly.com/question/31479424#

#SPJ11

An object is placed 50 cm in front of a concave mirror with a focal length of 25 cm. What is the magnification produced by the mirror? A) -2.0 B) -1.0 C) +1.0 D) -0.50 E) +1.5

Answers

The magnification produced by a concave mirror is -0.50. the correct answer is D)

The magnification produced by a concave mirror is given by the formula M = -v/u, where v is the image distance and u is the object distance. In this case, the object distance u is 50 cm and the focal length f is -25 cm (since it is a concave mirror). Using the mirror formula 1/f = 1/u + 1/v, we can solve for the image distance v:
1/f = 1/u + 1/v
1/-25 = 1/50 + 1/v
-1/25 = 1/v - 1/50
-2/50 = 1/v
v = -25 cm
Now we can use the magnification formula:
M = -v/u = -(-25)/50 = 0.5
Therefore, the correct answer is D) -0.50.

For more such questions on magnification , Visit:

https://brainly.com/question/28113233

#SPJ11

The magnification produced by the mirror is B) -1.0.

To calculate the magnification produced by the concave mirror, we can use the mirror equation and the magnification formula. The mirror equation is:

1/f = 1/u + 1/v

Where f is the focal length, u is the object distance, and v is the image distance.

Given: f = -25 cm (concave mirror focal length is negative) and u = -50 cm (object distance is also negative). We can find v using the equation:

1/(-25) = 1/(-50) + 1/v

Solving for v, we get v = -50 cm.

Next, we can find the magnification using the formula:

magnification = - (v/u)

Plugging in the values: magnification = -(-50/-50) = -1.0

So, the magnification produced by the mirror is B) -1.0.

Learn more about focal length brainly.com/question/29870264

#SPJ11

Other Questions
solve the initial value problem dy/dt 4y = 25 sin 3t and y(0) = 0 the 2-kg sphere a is moving toward the right at 10 m/s when it strikes the unconstrained 4-kg slender bar b. what is the angular velocity of the bar after the impact if the sphere adheres to the bar? which of the following countries offers maternity leave to mothers at 100 percent of their income for the longest number of weeks? do plant species differ int heir compensation points why was the nationalist ambitions in austria-hungary a failure? if you want to change data in a column to something more meaningful like internet instead of i, what feature do you want to use? TRUE/FALSE. In financial statement analysis, a single number can be very important given the electrochemical reaction, , what is the value of ecell at 25 c if [mg2 ] = 0.100 m and [cu2 ] = 1.75 m? A restaurant buys a freezer in the shape of a rectangular prism.dimensions of the freezer are shown. What is the volume of the freezer36 24 1/2 72 1/2 The uniform distribution defined over the interval from 25 to 40 has the probability density function f(x) = 1/40 for all x. f(x) = 5/8 for 25 < x < 40 and f(x)= 0 elsewhere. f(x) = 1/25 for 0 describe the characteristics of antipsychotic drugs, and discuss their use in treating schizophrenia is called The critical values z z or z/2 z / 2 are the boundary values for the: A. power of the test B. rejection region(s) C. Type II error D. level of significance Suppose that we reject a null hypothesis at the 0.05 level of significance. Then for which of the following values do we also reject the null hypothesis? A. 0.06 B. 0.03 C. 0.02 D. 0.04 is the reference in the auditors report to work performed by component auditors a scope limitation? explain. Fluid enters a tube with a flow rate of 0.020 kg/s and an inlet temperature of 20C. The tube, which has a length of 8 m and diameter of 20 mm, has a surface tempera ture of 30C. (a) Determine the heat transfer rate to the fluid if it is water. (b) Determine the heat transfer rate for the nanofluid of Example 2.2. messages that provide directions and messages that set expectations both involve telling others what to do.group startstrue or false identify the fallacy in the passage below: are you still spending the money you stole from me? even when layout and location drawings are provided, they may not include the ________ between the components. Assume that the Ecuyer Company uses the indirect method to depict cash flows. Indicate where, if at all, stock issued for equipment would be classified on the statement of cash flows. O Financing activities section. O Investing activities section. o Operating activities section. O Does not represent a cash flow. you are developing an azure app service web app. the app will use the microsoft authentication library for javascript (msal.js). you register the web app with the microsoft identity platform by using the azure portal. you need to configure the web app to receive the security tokens. the web app must process custom claims in the security tokens issued by azure active directory (azure ad). which value should you configure? suppose bubbles formed on the surface of the objects that you were submerging. how would these bubbles affect the measurement of the density of the objects? would the bubbles make the measured densities too large, or too small? explain.