Line a is parallel to line b. If the
measure of 27 is 114°, what is the
measure of 41?
21
34
65
114°= 78
a
b

The work done to stretch the spring from 16m to 19m will be 18 Joules and the natural length with which a force of about 72 N is used to keep the spring stretched will be 7.5m.

Spring force can be defined as the force which acts in the opposite direction to the displacement of the object. In order to stretch or compress the spring some amount of work has to be done. Which is given as,

where k = spring constant of the spring

         x = compression of spring

         W= Work required or spring work

Initial length is given by 9m

final length is given by  11m

When spring is stretched change in the length occurs denoted by x

x = final length - initial length = (11 - 9) = 2m

W = 1/2Kx²

W = 1/2 K (2)²

8×2 = 4K

16/4 = K

K = 4 N/m

(a) work is needed to stretch the spring from 16m to 19m

stretching length from 16 to 19m will be 3m

stretching length from cm to 30 is 40 cm is 10 cm which is 0.1m

x = final stretch of the spring = 16 - 19 = 3m

Work needed to stretch the spring from 16m to 19m is given

W = (0.5)K(3²)

W = (0.5)(4)(3²)

W = 2.0 × 9

W = 18 Joules

x is stretch of the spring beyond natural length

F = force = 72 N

Spring force is given as

F = k x

30 = (4) x

x = 7.5m

Learn more about Spring constant here:

https://brainly.com/question/14159361

#SPJ1

Answer: serous fluid

Explanation: The space between these two serous layers, the parietal and the visceral, is the pericardial cavity, which contains pericardial fluid.

Taking into account the definition of calorimetry, the heat energy that this sample of water absorbed is 199.87 cal.

Sensible heat is defined as the amount of heat that a body absorbs or releases without affecting its molecular structure.

The expression that allows to calculate heat exchanges is:

Q = c× m× ΔT

where:

In this case, you know:

Replacing in the definition of sensible heat:

Q = 4.184 J/gC× 50 g× 4 C

Solving:

Q= 836.8 J= 199.87 cal (1 J= 0.238846 cal)

Finally, the heat in this case is 199.87 cal.

Learn more about sensible heat:

brainly.com/question/12670283

#SPJ1

In psychology research, the laboratory experiment has long been regarded as the "gold standard."

This is so that causality can be clearly established and because only laboratory experiments can distinguish between cause and effect.

What is a laboratory?

The evidence suggests that Pythagoras of Samos, a well-known Greek philosopher and scientist, had a laboratory in his home.

This laboratory was set up by Pythagoras, who experimented with sound tones and string vibration.

In a painting by Albert Edelfelt from 1885, Louis Pasteur is shown comparing a note in his left hand to a bottle containing a solid in his right hand, without wearing any personal protective equipment.

To know more about laboratory, click the link given below:

https://brainly.com/question/14428286

#SPJ4

Answer:

The average speed of the car is 26.66kmh−1.

Explanation:

Tama po yan promise

Answer:

The average speed of the car can be calculated using the formula: average speed = total distance / total time.

Let's call the time taken to travel the first 30 km t1 and the time taken to travel the next 30 km t2. We know that:

t1 = 30 / 40 = 0.75 hours

t2 = 30 / 20 = 1.5 hours

The total distance is 60 km and the total time taken is t1 + t2 = 0.75 + 1.5 = 2.25 hours.

So the average speed is 60 / 2.25 = 26.67 km/hr.

Explanation:

'Mechanical waves require a medium for propagation' is the statement which most fundamentally distinguishes mechanical waves from electromagnetic waves. Correct option is B.

A wave's height (amplitude), frequency, and length are all ways to describe it. Any wave can be thought of as an energy-transferring disturbance.

Compared to mechanical waves, electromagnetic waves are different. The electromagnetic waves can move in vacuums since they have the ability, but sound waves and water cannot, so they require a medium to spread.

Electric and magnetic fields oscillate along with electromagnetic waves in a manner that is perpendicular to the direction of propagation.

Thus, mechanical waves require a medium for propagation.

To know more about waves:

https://brainly.com/question/30628285

#SPJ4

Answer:

To calculate the current flowing through the resistor, we can use Ohm's Law, which states that V = IR, where V is the voltage, I is the current, and R is the resistance.

In this case, the voltage is 6 volts and the resistance is 5 ohms, so:

I = V/R = 6/5 = 1.2 amps

To calculate the energy dissipated as heat in 10 seconds, we can use the formula:

E = I^2Rt, where E is the energy, I is the current, R is the resistance, and t is the time.

Substituting the values we have:

E = (1.2)^2 x 5 x 10 = 72 joules

Therefore, the current flowing through the resistor is 1.2 amps, and the energy dissipated as heat in 10 seconds is 72 joules.

Constructive interference is exactly at source A. Distance from source A to points of destructive interference are 3.00 meters and 10.50 meters.

When two coherent sources, A and B, emit radio waves with the same wavelength and are separated by a certain distance, they can interfere constructively or destructively at different points along the line connecting the sources. To determine the distances at which constructive interference and destructive interference occur, we can use the following equations:

For constructive interference:

d = mλ

For destructive interference:

d = (m + 1/2)λ

where d is the distance from source A to the interference fringe, λ is the wavelength of the radio waves, and m is an integer representing the order of the interference fringe.

To find the distance from source A to the point of constructive interference, we can use the equation for constructive interference with m = 0 (the first order of interference):

d = mλ = 0 x 6.00 m = 0 m

This means that the first point of constructive interference is exactly at source A.

At what distances from source A is there destructive interference between points A and B?

To find the distances from source A to the points of destructive interference, we can use the equation for destructive interference with m = 0 (the first order of interference) and m = 1 (the second order of interference):

For the first order of interference:

d = (m + 1/2)λ = (0 + 1/2) x 6.00 m = 3.00 m

For the second order of interference:

d = (m + 1/2)λ = (1 + 1/2) x 6.00 m = 10.50 m

Therefore, the distances from source A to the points of destructive interference are 3.00 meters and 10.50 meters, respectively. These are the two separate interference fringes that occur between point A and point B.

Learn more about constructive interference here:

https://brainly.com/question/16098226

#SPJ4

Although the accumulation and release of static electricity occurs in both lightning and a Van de Graaff generator, their complexity and size are different.

There are some significant distinctions between a Van de Graaff generator and lightning, despite the fact that both involve the accumulation and release of static electricity.

Using a moving belt, a Van de Graaff generator builds up a lot of static charge on a metal sphere or other item. The metal and the belt's friction move electrons from one surface to the other, causing a buildup of charge. A visible spark or even a minor arc can be produced between the sphere and another conductor when the charge accumulates up to a certain level.

On the other hand, lightning is a natural occurrence that happens when there is a buildup of static charge.

Learn more about  accumulation here:

https://brainly.com/question/15907765

#SPJ4

Answer:

Below

Explanation:

To convert K to °C    just subtract 273.15   from the K  value

The specific heat capacity of a material is defined as the amount of heat energy required to raise the temperature of 1 gram of the material by 1 degree Celsius. In this case, we are given that the specific heat .

Q = m x c x ΔT

Substituting the given values, we get:

Q = 20g x 0.385 J/g°C x (50°C - 20°C)

Q = 20g x 0.385 J/g°C x 30°C

Q = 231 Joules

To know more about specific heat capacity , check out :

https://brainly.com/question/27991746

#SPJ4

The car will have traveled through an angle of approximately 9.29 degrees when the magnitude of its total acceleration is 2.2 m/s^2.

To solve this problem, we need to determine the magnitude of the radial acceleration experienced by the car as it moves along the curve. The radial acceleration can be found using the equation:

ar = v^2/r

where v is the tangential velocity of the car and r is the radius of the curve.

Since the car starts from rest, its initial tangential velocity is zero, and its radial acceleration is equal to its total acceleration. Therefore, we can write:

ar = a

a = v^2/r

We can rearrange this equation to solve for the tangential velocity of the car:

v = √(ar * r)

Substituting the given values, we have:

v = √(2.2 m/s^2 * 100 m) = 14.5 m/s

Next, we can use the tangential velocity to determine the angle through which the car has traveled. The tangential distance traveled by the car can be found using the equation:

d = v * t

where t is the time elapsed.

Since the tangential acceleration is given as 1.3 m/s^2, we can use this to determine the time elapsed:

a = v / t

t = v / a

Substituting the values, we have:

t = 14.5 m/s / 1.3 m/s^2 = 11.15 s

Finally, we can use the time elapsed and the radius of the curve to find the angle through which the car has traveled:

θ = d / r = v * t / r = (14.5 m/s) * (11.15 s) / (100 m) = 0.162 radians = 9.29 degrees

So, the car will have traveled through an angle of approximately 9.29 degrees when the magnitude of its total acceleration is 2.2 m/s^2.

Learn more about the magnitude of its total acceleration:

https://brainly.com/question/17205919

#SPJ4

The force applied on the small piston in order to lift 20,000N on the large piston is 0.8×10³ N.

According to Pascal's law, the pressure distribution in the confined fluid is equal in all directions. Therefore, if the cross-sectional area of the output cylinder is larger than the input cylinder, then the output force is larger than the input force. The ratio of the output force to the input force on the input piston is called the mechanical advantage, and if it is greater than one, then force multiplication takes place.

Given,  F₁=20000 N is the weight of the car

r₂=4.0 cm is the radius of the small piston

r₁=20cm is the radius of the large piston

F₂ is the force applied on the small piston.

Pressure in the large cylinder = Pressure in the smaller cylinder,

P₁=P₂

F₁/A₁=F₂/A₂

F₂= 0.8×10³ N.

For further learning about pressure, refer to the link: https://brainly.com/question/4224481

#SPJ4

Friction is not always negligible, as it can have significant effects on the behavior of objects in motion.

Friction is a force that opposes the motion of two surfaces in contact with each other. The magnitude of the frictional force depends on the nature of the surfaces in contact, the force pressing the surfaces together, and the relative motion between the surfaces.

In some cases, the effects of friction can be ignored because they are small compared to other forces at play. For example, in situations where an object is moving through a fluid, such as air or water, the effects of friction may be negligible compared to the forces of drag and buoyancy.

In other situations, the effects of friction cannot be ignored. For example, in a car's braking system, the friction between the brake pads and the rotor is necessary to slow down and stop the car. Without this friction, the car would not be able to come to a complete stop.

Learn more about friction here

brainly.com/question/13000653

#SPJ4

The correct option for chemical reaction is "The mass definitely stayed the same because the ranges of uncertainty overlap exactly."

As given that  student measures the mass of a solution before and after a chemical reaction takes place that is he measure the mass which is 50.25g with uncertainty of 0.05g.  In this case the mass would be same .

Mass is a quantitative measure of inertia in physics and a fundamental property of all matter. In effect, it is the resistance that an object offers to changes in velocity or position when a force is applied.

The greater the mass of an object, the smaller the change caused by an applied force. The unit of mass in the International System of Units (SI) is the kilogram, which is defined by Planck's constant and is equal to 6.62607015 × 10−34 joule-seconds.

One joule is equal to one kilogram square meter per second. Seconds and meters are already defined by other physical constants, so kilograms are determined by the exact measurement of Planck's constant.

(Until 2019, the kilogram was defined by a platinum iridium cylinder called the International Prototype Kilogram held at the International Bureau for Weights and Measures in Sèvres, France.)

know more about mass click here;

https://brainly.com/question/30673935

#SPJ4

Nodes are points with zero amplitude, while antinodes are points with maximum amplitude in standing waves.

Nodes and antinodes are terms used to depict the areas of least and most extreme amplitudes, separately, in standing waves. A standing wave is a wave that has all the earmarks of being fixed on the grounds that it is the consequence of the obstruction of two rushes of a similar recurrence and plentifulness going in inverse headings.

Nodes are focuses along the standing wave where the plentifulness is zero. These focuses relate to where the peak of one wave agrees with the box of the other wave, bringing about horrendous impedance.

Antinodes, then again, are focuses along the standing wave where the plentifulness is at a most extreme. These focuses relate to where the peaks and box of the two waves support one another, subsequent in helpful obstruction.

Nodes and antinodes are significant in many fields, including acoustics, optics, and quantum mechanics.

To learn more about nodes and antinodes, refer:

https://brainly.com/question/3838585

#SPJ4

The light for a telescope comes from astronomical objects like stars, galaxies, and planets, not from an internal source.

The main job of the telescope is to gather and concentrate this light, enlarging and enhancing the image via a variety of mirrors or lenses.

The light is collected and focused at a focal point by the telescope's objective lens or primary mirror, where it is enlarged by an eyepiece or camera.

Depending on the user's intended use of the telescope for scientific or observational purposes, telescopes may be built to focus on a particular kind of light, such as visible light, infrared, ultraviolet, or radio waves.

To reduce interference from the Earth's atmosphere, telescopes can also be installed on the surface of the earth or in orbit.

Learn more about the telescope at

https://brainly.com/question/556195

#SPJ4

I would look for these wavelengths since exploding stars mostly produce gamma-rays and X-rays.

Two primary instruments make up the Fermi telescope. It has a sizable telescope that discovers gamma rays with energies between 10 million and 300 billion times that of visible light. Moreover, the spacecraft carries detectors for observing gamma-ray bursts. Gamma ray bursts are short gamma ray flashes.

IR perspective Dust is significantly easier for infrared light to penetrate than optical light. For this reason, infrared astronomy is best suited for gaining knowledge of the universe's dusty regions. Star-forming areas are one instance.

To know more about gamma rays visit:

https://brainly.com/question/23281551

#SPJ4

Density altitude is a measurement of air density used to estimate aeroplane performance. It is determined by combining temperature, pressure, and humidity. The density altitude formula is as follows:

Pressure altitude + [120 x (OAT - ISA temperature)] = density altitude

In the above formula:

The height in the standard atmosphere where the atmospheric pressure equals the measured pressure is referred to as pressure altitude.

OAT is the temperature of the outside air in degrees Celsius.

The International Standard Atmosphere (ISA) temperature is the standard temperature for a certain altitude (ISA).

The altitude in feet above sea level at which the air density is equal to the air density at the actual altitude, temperature, and pressure is the outcome of this computation. A high density altitude indicates that the air is less dense, which can reduce aircraft performance, whereas a low density altitude indicates that the air is denser, which can improve aircraft performance.

For more such questions on Density altitude, click on:

https://brainly.com/question/30629854

#SPJ4

The net electric force that the two charges would exert on an electron placed at point x = 0.200 m is:F = -2.40 x 10-9 N.

Force is an infants that causes an object to change its motion direction say for other physical quantity force can be caused by physical contact or they can be created by feels like rabbit in magnetism for skin also be internal such as force of fraction tension in compression.

The net electric force that the two charges would exert on an electron placed at point x = 0. 200 m is calculated using Coulomb’s law. Coulomb’s law states that the magnitude of the force between two point charges is directly proportional to the product of the charges, and inversely proportional to the square of the distance between them.

The equation for the electric force is F = k * q1 * q2 / r2, where k is Coulomb’s constant (8.99 x 109 Nm2/C2), q1 and q2 are the two charges, and r is the distance between them.

In this case, the two charges are q1 = +4.0 x 10-8 C and q2 = -4.0 x 10-8 C. The distance between them is r = 0.2 m.

Therefore, the net electric force that the two charges would exert on an electron placed at point x = 0.200 m is:

F = (8.99 x 109 Nm2/C2) * (4.0 x 10-8 C) * (-4.0 x 10-8 C) / (0.2 m)2

F = -2.40 x 10-9 N

To know more about force click-
https://brainly.com/question/12785175
#SPJ4

The net electric force that the two charges would exert on an electron placed at point x = 0.200 m is:[tex]F = -2.40 \times 10^{-9} N.[/tex]

Force is an infants that causes an object to change its motion direction say for other physical quantity force can be caused by physical contact or they can be created by feels like rabbit in magnetism for skin also be internal such as force of fraction tension in compression.

The net electric force that the two charges would exert on an electron placed at point x = 0. 200 m is calculated using Coulomb’s law. Coulomb’s law states that the magnitude of the force between two point charges is directly proportional to the product of the charges, and inversely proportional to the square of the distance between them.

The equation for the electric force is[tex]F = k \times q1 \times q2 / r^2,[/tex] where k is Coulomb’s constant ([tex]8.99 \times 10^9 Nm^2/C^2[/tex]), q1 and q2 are the two charges, and r is the distance between them.

In this case, the two charges are q1 = +4.0 x 10-8 C and q2 = -4.0 x 10-8 C. The distance between them is r = 0.2 m.

Therefore, the net electric force that the two charges would exert on an electron placed at point x = 0.200 m is:

[tex]F = (8.99 \times 10^9 Nm^2/C^2) \times (4.0 \times 10-8 C) \times (-4.0 \times 10^{-8} C) / (0.2 m)^2 \\F = -2.40 \times 10-9 N[/tex]

To know more about force click

brainly.com/question/12785175

#SPJ4

Sort each item into the correct bin based on whether it describes lunar eclipses or solar eclipses.

- occurs when the Moon is on the direct opposite side of Earth from the Sun

Traditionally, eclipses are classified into two types: solar and lunar. Solar eclipses occur when the Moon passes between Earth and the Sun, casting a moving shadow on the Earth's surface. Lunar eclipses occur when the Earth passes between the Sun and the Moon, producing a shadow on the Moon.

A lunar eclipse is sometimes referred to as a blood moon since the only sunlight reaching the moon during an eclipse travels via Earth's atmosphere.

learn more about lunar eclipses or solar eclipses.

https://brainly.com/question/25178656

#SPJ4

The velocity of the particle is 0 m/s since the displacement is 0 when t = a.

Velocity is a measure of the rate and direction of change in the position of an object. It is a vector quantity, consisting of both speed and direction. Velocity is most commonly expressed in terms of distance traveled per unit of time. The average velocity of an object over a period of time is its displacement divided by the time duration. Speed, on the other hand, is a scalar quantity and is the magnitude of the velocity vector. It is the rate of change in position of an object, regardless of direction.

To learn more about velocity

https://brainly.com/question/24445340

#SPJ4

The velocity variates different at different time i.e. when

t = 1, v = -16m/s

t = 2, v = -2.25m/s

t = 3, v = -1.77m/s

The concept of velocity refers to the rate and direction of motion of a point. For instance, the orientation of a circular path is always perpendicular to the line that connects a point to the center of the circle. A point always advances down a route that is perpendicular to it (a radius). The magnitude of the velocity is the rate of motion of the point along its path through time.

If a point moves along a path and covers a certain distance in a predetermined amount of time, its average speed over that period of time is equal to the distance covered divided by the travel time. For instance, the average speed of a train traveling 100 kilometers in two hours is 50 km/h.

v(t) =ds / dt = d(8/t²) / dt = -16/t³

Velocity of the particle at time t = a

v(a)= - 16 / a³

Velocity of the particle at time t = 1

v(1) = -16m/s

Velocity of the particle at time t = 2

v(2) = -2.25m/s

Velocity of the particle at time t = 3 v(3) = - 1.77m/s

To learn more about velocity of particle from given link

https://brainly.com/question/12923892

#SPJ4

To see the Sun and Jupiter as distinct points of light from a distance of 10 light-years, we would need an angular resolution of approximately 0.57 arcseconds.

To calculate the angular resolution required to see the Sun and Jupiter as distinct points of light from a distance of 10 light-years, we can use the formula:

θ = 1.22 λ/D

Where θ is the angular resolution in radians, λ is the wavelength of the light being observed, and D is the diameter of the telescope lens or mirror.

Assuming that we are observing in visible light with a wavelength of 550 nanometers, and using the diameter of the Hubble Space Telescope's primary mirror as an example (which is approximately 2.4 meters), we can plug in these values to get:

θ = 1.22 (550 × 10^-9 meters) / 2.4 meters

θ ≈ 2.8 × 10^-9 radians

To convert this to arcseconds (a more commonly used unit of angular resolution), we can multiply by the conversion factor of 206,265 arcseconds/radian:

θ ≈ 0.57 arcseconds

Therefore, to see the Sun and Jupiter as distinct points of light from a distance of 10 light-years, we would need an angular resolution of approximately 0.57 arcseconds. This is an extremely high level of resolution, beyond the capabilities of most ground-based telescopes, but it can be achieved with space-based observatories like the Hubble Space Telescope.

Complete question:

Suppose you were looking at our own Solar System from a distance of 10 light-years: What angular resolution would you need to see the Sun and Jupiter as distinct points of light?

Learn more about angular resolution:

https://brainly.com/question/30585791

#SPJ4

180 degrees Fahrenheit is equal to 82.22 degrees Celsius.

Temperature is a measure of the average kinetic energy of the particles in a substance. Temperature conversion is the process of converting a temperature measurement from one unit to another. The most common units for temperature measurement are Celsius (C) and Fahrenheit (F).

The temperature conversion from Fahrenheit to Celsius can be done using the formula: C = (F - 32) * 5/9, where C is the temperature in Celsius and F is the temperature in Fahrenheit.

To convert 180 degrees Fahrenheit to Celsius, we can plug in the values into the formula:

C = (180 - 32) * 5/9

C = 148 * 5/9

C = 82.22

So, The temperature 180 degrees of Fahrenheit is equivalent to 82.22 degrees Celsius.

To know more about temperature conversion here:

https://brainly.com/question/13421795#

#SPJ11

Even when there is no discernible change in elevation, station pressures quickly shift across short horizontal distances.

Aircraft performance and flight levels are both based on pressure altitude, which is crucial for aircraft operating at or above 18,000 feet. Pressure altitude is adjusted for non-standard temperature to produce density altitude.

The station pressure, which is the actual barometric pressure of a location, is the pressure that is measured at a particular elevation. The pressure indication that is most frequently heard in radio and television broadcasts is the altimeter setting. It is not the station's actual barometric pressure.

To know more about pressures visit:-

https://brainly.com/question/30482677

#SPJ4

The optimal temperature for lactase activity is : 125 to 135 degrees F

125 to 135 degrees F is the optimum temperature for lactase activity. At temperatures higher than this range, enzyme quickly becomes denatured and is therefore unable to break down the milk sugar.

Optimum pH for lactose hydrolysis is 6.5, which is very close to the pH of milk. Heating lactase for 1 min results in 97% inactivation at 60° C and complete inactivation at 70° C and some inactivation also occurs at 40° C over 1-hour incubation.

It was observed that heat treatment of milk increases lactase activity, with  maximum activity increase found when milk was heated at 55°C.

To know more about lactase activity, refer

https://brainly.com/question/2945627

#SPJ4

The statement "the first basic step in solving force and motion problems generally involves identifying all of the forces acting on an object" is true because the first step of question is to draw FBD.

A free body diagram (FBD) is a visual representation that shows all the forces acting on an object. It is a simple sketch that isolates an object of interest and shows all the forces acting on it, including the direction and magnitude of each force.

Free body diagrams are commonly used in physics and engineering to analyze and solve problems related to force and motion. By drawing a free body diagram, one can easily identify all the forces acting on an object and determine their net effect on the object's motion.

To know more about motion here

https://brainly.com/question/453639

#SPJ4

Vertical axis wind turbines (VAWTs) have some disadvantages compared to horizontal axis wind turbines (HAWTs). Here are a few:

To know more about VAWT , check out :

https://brainly.com/question/928271

#SPJ4