According to the forces of attraction , as water passes on in water cycle its state changes from liquid to vapor and solid in form of ice and then back to liquid.
What are forces of attraction?Forces of attraction is a force by which atoms in a molecule combine. it is basically an attractive force in nature. It can act between an ion and an atom as well.It varies for different states of matter that is solids, liquids and gases.
The forces of attraction are maximum in solids as the molecules present in solid are tightly held while it is minimum in gases as the molecules are far apart . The forces of attraction in liquids is intermediate of solids and gases.
The physical properties such as melting point, boiling point, density are all dependent on forces of attraction which exists in the substances.
Learn more about forces of attraction,here:
https://brainly.com/question/23841038
#SPJ1
Determine the molar masses of the following compounds.
a. Al2(SO4)3 b. (NH4)3PO4 c. C2H4O2
The molar masses of the compounds are;
a) 342 g/mol
b) 149 g/mol
c) 60 g/mol
What is the molar mass?Molar mass is the mass of one mole of a substance, usually expressed in grams per mole (g/mol). It is calculated by adding up the atomic masses of all the atoms in a molecule, or the formula weight of a compound. The molar mass is an important concept in chemistry, as it allows scientists to calculate the amount of a substance present in a sample based on its mass or vice versa.
We can calculate the molar masses as follows;
a) 2(27) + 3(32 + 4(16))
= 342 g/mol
b) 3(14 + 4(1)) + 31 + 4(16)
= 149 g/mol
c) 2(12) + 4(1) + 2(16)
= 24 + 4 + 32
= 60 g/mol
Learn more about molar mass:https://brainly.com/question/22997914
#SPJ1
Classify each of the following pure substances as an element or a compound.
1. a silicon (Si) chip
2. oxygen (O2)
3. hydrogen peroxide (H2O2)
4. rust (Fe2O3)
5. methane (CH4) in natural gas
Element (Si), Element (Oxygen) in molecular form (O2), Compound (H2O2), Compound (Fe2O3), Compound (CH4).
Silicon (Si) is a chemical element, which means that it is a pure substance consisting of only one type of atom. A silicon chip is made of pure silicon, so it is an element.Oxygen (O2) is also a chemical element, but in this case, it is in molecular form. Molecular oxygen (O2) is a colorless, odorless gas that makes up about 21% of Earth's atmosphere. Since it is a pure substance consisting of only one type of molecule, it is still considered an element.Hydrogen peroxide (H2O2) is a compound, which means that it is made up of two or more different elements chemically bonded together. In the case of hydrogen peroxide, it is composed of two hydrogen atoms and two oxygen atoms chemically bonded together. Hydrogen peroxide is commonly used as a disinfectant and bleaching agent.Rust is a compound made up of iron (Fe) and oxygen (O). Specifically, rust is the compound Fe2O3, which forms when iron reacts with oxygen in the presence of water. Rust is a common form of corrosion that can weaken and damage metal objects over time.Methane (CH4) is also a compound, made up of one carbon atom and four hydrogen atoms chemically bonded together. Methane is the primary component of natural gas, a fossil fuel that is used as a source of energy.Learn more about compound here https://brainly.com/question/13157010
#SPJ4
Addition of a strong base to a solution containing ______ will release a gas which will cause a piece of moist, red litmus held above the reaction solution to turn blueA) NH4+B) CO32-C) Cl-
The correct answer is A) NH4+. When a strong base is added to a solution containing NH4+, it reacts with water to produce ammonia gas (NH3) and hydroxide ions (OH-), according to the following equation:
NH4+ + OH- → NH3 + H2O
The ammonia gas produced is responsible for turning the moist red litmus blue, indicating the presence of a base. This reaction is commonly referred to as the ammonium ion hydrolysis reaction.
In contrast, adding a strong base to a solution containing CO32- or Cl- ions will not produce a gas that can cause the litmus paper to turn blue. The carbonate ion (CO32-) would react with a strong acid to release carbon dioxide gas, but it will not release gas upon addition of a strong base. Similarly, the chloride ion (Cl-) is a spectator ion and does not participate in the reaction with the base.
To know more about ammonia click here:
brainly.com/question/14672082
#SPJ4
When brown iodine is exposed to starch it turns dark purple. In an experiment, you placed a cornstarch and glucose solution within a small plastic bag. Next, you placed the bag in a beaker with water and 10 drops of iodine. After 10 minutes, the solution in the bag turned dark purple and glucose could be found in the iodine water within the beaker. Select all that apply.
-The iodine moved into the plastic bag
-The cornstarch moved into the beaker
-Iodine and glucose have a smaller molecular size than cornstarch
-Cornstarch has a smaller molecular size than iodine or glucose
-The plastic bag was selectively permeable
The solution in the bag turned dark purple and glucose could be found in the iodine water within the beaker because:
a. The iodine moved into the plastic bag.b. The cornstarch moved into the beaker.d. Cornstarch has a smaller molecular size than iodine or glucose.e. The plastic bag was selectively permeable.What is diffusion?The definition of diffusion is the transfer of individual molecules of a material from a region of higher concentration to a region of lower concentration over a semipermeable barrier.
The iodine experiments show the process of diffusion.
Therefore, the correct options are a, b, d, and e.
To learn more about diffusion, refer to the link:
https://brainly.com/question/14852229
#SPJ1
true/false. laundry detergent is not just soap. there are certain chemicals in detergent that allow greater solvency, more cleaning power, less suds, and opens up the weave of the fabrics to allow greater chemical penetration.
The statement (laundry detergent is not just soap. there are certain chemicals in detergent that allow greater solvency, more cleaning power, fewer suds, and open up the weave of the fabrics to allow greater chemical penetration) this is true because laundry detergents often contain a number of additional chemicals that boost their cleaning ability and make them more effective than soap alone.
Soap alone is not laundry detergent. While soap and detergent are both surfactants that are used to clean clothes, laundry detergents typically contain more of these chemicals than soap.
Enzymes, builders, bleaches, and other additives are examples of the extra chemicals that can be added to the detergent to help with stain removal, water softening, whitening, and overall effectiveness. Laundry detergents are also designed to produce fewer suds than soap, which can assist to protect washing machines and lower the quantity of water required to rinse the garments.
Want to know more about detergent visit the link which is given below;
https://brainly.com/question/11727239
#SPJ4
How much 6M HCl do you need to add if you have 800 mL of 100mM TRIS, pH 10.2 and you wish to lower the pH to 7.0?
You would need to add approximately 0.2 μL of 6M HCl acid to 800 mL of 100 mM TRIS buffer at.
How much 6M HCl do you need to add?
To calculate how much 6M HCl you need to add to lower the pH of a 800 mL solution of 100 mM TRIS from pH 10.2 to pH 7.0, you need to determine the initial and final concentrations of the TRIS buffer, and use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
where;
[A-] is the concentration of the deprotonated form of TRIS (TRIS-), [HA] is the concentration of the protonated form (HTRIS), and pKa is the acid dissociation constant of TRIS (pKa = 8.1).First, calculate the initial concentration of TRIS- and HTRIS:
TRIS- concentration = 100 mM × 10^(-10.2) = 6.31 × 10^(-6) M
HTRIS concentration = 100 mM - 6.31 × 10^(-6) M = 99.99999369 mM
Next, determine the desired final concentration of TRIS- and HTRIS:
TRIS- concentration = 10^(-7.0) = 1 × 10^(-7) M
HTRIS concentration = 100 mM - 1 × 10^(-7) M = 99.9999999 mM
Now, use the Henderson-Hasselbalch equation to calculate the amount of HCl needed to achieve the desired pH:
pH = pKa + log([A-]/[HA])
7.0 = 8.1 + log([1 × 10^(-7)]/[99.9999999])
log([1 × 10^(-7)]/[99.9999999]) = -1.1
[1 × 10^(-7)]/[99.9999999] = 0.0794
[1 × 10^(-7)] = 0.0794 × [99.9999999]
[1 × 10^(-7)] = 7.93999993 × 10^(-6) M
[HA] = 100 mM - 7.93999993 × 10^(-6) M = 99.99999206 mM
The difference in [H+] concentration between the initial and final buffer conditions is:
[H+] concentration difference = [HA]initial - [HA]final
= 99.99999369 mM - 99.99999206 mM
= 0.00000163 M
To calculate the amount of 6M HCl needed to achieve this change in [H+], use the following formula:
moles of HCl = volume of buffer (L) × concentration difference (M)
where;
volume of buffer is 0.800 L (800 mL converted to liters).moles of HCl = 0.800 L × 0.00000163 M = 1.304 × 10^(-6) moles
Finally, convert moles of HCl to volume of 6M HCl needed:
volume of 6M HCl = moles of HCl ÷ concentration of HCl
The concentration of 6M HCl is 6 mol/L or 6,000 mM.
volume of 6M HCl = (1.304 × 10^(-6) moles) ÷ (6,000 mM)
= 0.219 μL or approximately 0.2 μL (microliters)
Learn more about acid concentration here: https://brainly.com/question/30669323
#SPJ1
5. calculate the number of atoms in each sample. a. 5.18 g p b. 2.26 g hg c. 1.87 g bi d. 0.082 g sr
The number of atom in 5.18 g Pb is 151 x 10²³ atoms and 2.26 g Hg is 68 x 10²³ atoms
Elaborating:a. 5.18 g Pb:
n = m/M = 5.18 g / 207.2 g/mol = 0.025 moles
N = n x N₀ = 0.025 moles x 6.022 x 10²³ atoms/mol = 151 x 10²³ atoms
b. 2.26 g Hg:
n = m/M = 2.26 g / 200.6 g/mol = 0.0113 moles
N = n x N₀ = 0.0113 moles x 6.022 x 10²³ atoms/mol = 68 x 10²³ atoms
c. 1.87 g Bi:
n = m/M = 1.87 g / 208.9 g/mol = 0.009 moles
N = n x N₀ = 0.009 moles x 6.022 x 10²³ atoms/mol = 54 x 10²³ atoms
d. 0.082 g Sr:
n = m/M = 0.082 g / 87.62 g/mol = 0.000939 moles
N = n x N₀ = 0.000939 moles x 6.022 x 10²³ atoms/mol = 56 x 10² atoms
A particle known as an atom is made up of a nucleus of protons and neutrons surrounded by an electron cloud. The chemical elements are distinguished from one another by the number of protons in their atoms, which is the basic particle of the elements.
What do atoms consist of?There are two kinds of elementary particles that make up an atom: quarks and electrons. The space that surrounds an atom's nucleus is occupied by electrons. The electrical charge of an electron is -1. The nucleus of an atom is made up of protons and neutrons, which are made up of quarks.
Learn more about atoms:
brainly.com/question/6258301
#SPJ1
Calculate the percent composition of Zn and Cu in your penny
Zinc: 0.75%, Copper: 99.25%. Zn and Cu are the symbols for zinc and copper, two chemical elements.
What are Zn and Cu?Generally, The composition of a penny is 97.5% zinc and 2.5% copper by weight. The zinc core of a penny is covered by a thin copper plating.
The copper plating is what gives the penny its distinct copper color.
Read more about Zn and Cu
https://brainly.com/question/27869669
#SPJ1
Write the equilibrium expression Kc for the following process. 3O2(g) <=> 2O3(g)
The equilibrium expression Kc for the reaction can be written as -
[tex]Kc = \frac{O_{3}^{2} }{O_{2} ^{3} }[/tex]
What is equilibrium constant Kc?Equilibrium constant of a chemical reaction at equilibrium is defined as the ratio of concentration of products to the concentration of reactants, each raised to their respective stoichiometric coefficients.
The expression that links Kc to the equilibrium concentration of reactants and products and stoichiometry of the equation is called equilibrium expression.
Kc is the equilibrium constant where subscript c refers to the fact that concentrations have been used in the calculations. The units of Kc depend on the equilibrium expression.
Therefore, the equilibrium expression Kc for the reaction can be written as -
[tex]Kc = \frac{O_{3}^{2} }{O_{2} ^{3} }[/tex]
Learn more about equilibrium constant Kc, here:
https://brainly.com/question/19669218
#SPJ1
The preferred arrangement of electrons in a molecular structure can be determined by calculating the _______ of each atom in the molecule.
Answer: Valence, Atoms
a 250 ml sample of oxygen is collected over water at 25c and 760.0 torr pressure. what is the pressure of the dry gas alone? ( vapor pressure of water at 25c is on chart above)
The pressure of the dry oxygen gas alone is 736.2 torr.To determine the pressure of the dry oxygen gas, we need to first account for the contribution of water vapor to the total pressure. At a temperature of 25°C, the vapor pressure of water is 23.8 torr [1].
Since the sample of oxygen was collected over water, the total pressure is the sum of the pressure of the oxygen gas and the vapor pressure of water. Thus:
total pressure = pressure of oxygen gas + vapor pressure of water
760.0 torr = pressure of oxygen gas + 23.8 torr
Solving for the pressure of the oxygen gas alone, we get:
pressure of oxygen gas = 760.0 torr - 23.8 torr
pressure of oxygen gas = 736.2 torr
Therefore, the pressure of the dry oxygen gas alone is 736.2 torr.
Find out more about pressure
brainly.com/question/30054511
#SPJ4
A mass is recorded as 15.02 g. Given the accepted level of uncertainty in any recorded measurement, the mass could vary within the range ______
a. 15.01 - 15.03 g b. 15.00 - 15.10 g c. 14.92 - 15.12 g d. 14.95 - 15.05 g
The mass could vary within the range of 15.00 - 15.04 g. So, the correct option is B.
When a measurement is made, there is always some level of uncertainty associated with it due to limitations in the precision of the instrument being used or other factors. The level of uncertainty can be expressed using the significant figures of the measurement. In this case, the mass is recorded to two decimal places, so the uncertainty is typically assumed to be ±0.01 g.
Therefore, the range of possible values for the mass would be 15.02 ± 0.01 g, or 15.01 - 15.03 g. Option a is the closest range to this value. It's important to keep in mind that the range of uncertainty may be larger or smaller depending on the instrument used and the level of precision required for a particular application.
You can learn more about accepted level of uncertainty at
https://brainly.com/question/30325664
#SPJ4
these five structures all have distinguishing absorptionsi nthe ir match each structure with its characteristic absorption
The answer is Structure 1) very broad, centered about 3330 cm-1.; 2) strong, sharp 1717 cm-1 ; 3) broad with spikes at 3367cm-1 and 3392cm-1.; 4) sharp, 2254cm-1; 5) strong, slightly broadened, 1645cm-1.
The structure with their respective characteristics are:
Structure 1: very broad, centered about 3330 cm-1.
Structure 2: strong, sharp 1717 cm-1.
Structure 3: broad with spikes at 3367cm-1 and 3392cm-1.
Structure 4: sharp, 2254cm-1 .
Structure 5: strong, slightly broadened, 1645cm-1.
OH (hydroxide), a chemical compound made up of a single oxygen atom bonded to a single hydrogen atom. It is usually written OH- in aqueous solutions.
O, [tex]NH_{2}[/tex] and CN are chemical symbols. O is oxygen, NH2 is an amine function and CN is a cyanide function. It is functional group consisting of the nitrogen atom bonded to one or two hydrogen atoms. Cyanide is a functional group consisting of a carbon atom bonded to a nitrogen atom. Both functional groups are very reactive and are also found in many organic compounds.
Full Question:
These five structures all have distinguishing absorption in the IR. Match each structure with its characteristic absorption.
Structure 1Structure 2Structure 3Structure 4Structure 5(a) sharp, 2254 cm-1
(b) very broad, centered about 3330cm-1
(c) strong, slightly broadened, 1645cm-1
(d) broad with spikes at 3367cm-1 and 3392cm-1
(e) strong, sharp 1717cm-1
To know more about Chemical structure:
brainly.com/question/27517802
#SPJ4
Calculate the mass in 488 mol of calcium carbonate, CaCO3
Calcium carbonate is the active ingredient in agricultural lime.
Calcium carbonate is the calcium salt with formula CCaO3. It has a role as an antacid, a food coloring, a food firming agent and a fertilizer and much more. It is a calcium salt, a carbonate salt, a one-carbon compound and an inorganic calcium salt.
Calcium carbonate is used therapeutically as a phosphate buffer.
488 moles of calcium carbonate (CaCO3) can be calculated by using its molecular weight. Calcium carbonate has a molecular weight of 100.0869 g/mol. To calculate the mass of 488 moles, we can multiply the molecular weight by the number of moles:
mass = molecular weight x number of moles
mass = 100.0869 g/mol x 488 mol
mass = 48,842.4072 g
So, the mass of 488 moles of calcium carbonate is approx. 48,842.4072 grams.
To learn more about calcium click here,
https://brainly.com/question/27798376
A student chromatographs a mixture, and after developing the spots with a suitable reagent he observes the following: What are the R_f values?
To calculate the R_f values in the student's experiment, you would need to measure the distance traveled by each solute spot and the distance traveled by the solvent front. Then, you would divide the distance traveled by each solute spot by the distance traveled by the solvent front to get the R_f value for each spot.
The R_f values are the ratio of the distance traveled by the solute to the distance traveled by the solvent. It is calculated by dividing the distance traveled by the solute by the distance traveled by the solvent front.
In chromatography, the R_f value is used to identify compounds by comparing the R_f value of a known compound to the R_f value of an unknown compound.
For example, if a solute spot traveled 4 cm and the solvent front traveled 8 cm, the R_f value for that spot would be 4/8 = 0.5. If another solute spot traveled 6 cm and the solvent front traveled 8 cm, the R_f value for that spot would be 6/8 = 0.75.
By calculating the R_f values for each spot, the student can compare the R_f values to known compounds to identify the components of the mixture.
To know more about chromatography, refer here:
https://brainly.com/question/30907934#
#SPJ11
When a sample of a gas is heated in a sealed, rigid container from 200 K to 400 K, the pressure exerted by the gas is:a) decreased by a factor of 2.b) increased by a factor of 2.c) decreased by a factor of 200.d) increased by a factor of 200.
the pressure will be increased by a factor of 2.
what is the relationship between the pressure, volume and the temperature ?
The relationship between the pressure, volume, and temperature of a gas is described by the ideal gas law, which is expressed as PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the absolute temperature. According to this law, the pressure of a gas is directly proportional to its temperature, assuming that the volume and number of moles remain constant.
In the given scenario, the gas is heated from 200 K to 400 K, while the container remains sealed and rigid, which means that the volume and number of moles of gas remain constant. As a result, the pressure of the gas must increase by a factor of 2, since the temperature has also increased by a factor of 2.
This can also be explained by the kinetic theory of gases, which states that the pressure of a gas is related to the average kinetic energy of its particles. When the gas is heated, its particles gain kinetic energy and move faster, which causes them to collide with the walls of the container more frequently and with greater force. This increase in collision frequency and force results in an increase in pressure, as described by the ideal gas law.
To learn more about pressure follow the given link: https://brainly.com/question/28012687
#SPJ1
Chemistry please helpppp
The term mole concept is used here to determine the number of atoms in 55.2 g of NaOH. The number of atoms in 55.2 g of NaOH is 8.31 × 10²³.
What is mole?One mole of a substance is defined as that quantity of it which contains as many entities as there are atoms exactly in 12 g of carbon - 12. The formula used to calculate the number of moles is:
Number of moles (n) = Given mass / Molar mass
n = 55.2 / 39.99 = 1.380 moles
a. Number of atoms = n × 6.022 × 10²³
1.380 × 6.022 × 10²³ = 8.31 × 10²³
b. Number of moles = 4.58 × 10²³ / 6.022 × 10²³ = 0.7605 moles
Mass of (NH₄)₂CO₃ = 0.7605 × 96.09 = 73.07 g
c. Number of moles = 1.46 × 10²⁴ / 6.022 × 10²³ = 0.242 moles
Mass of CaCl₂ = 0.242 × 110.98 = 26.85 g
d. Number of moles = 1.230 / 187.56 = 0.0065 moles
Number of atoms = 0.0065 × 6.022 × 10²³ = 3.91 × 10²¹
To know more about mole, visit;
https://brainly.com/question/30307377
#SPJ1
Suppose the concentration of glucose inside a cell is 0.1 mM and the cell is suspended in a glucose solution of 0.01 mM.Part A) What would be the free energy change involved in transporting 10−6 mole of glucose from the medium into the cell? Assume T= 37 ∘C. Answer: 5.93×10−6 kJPart B) What would be the free energy change involved in transporting 10−6 mole of glucose from the medium into the cell if the intracellular and extracellular concentrations were 1 mM and 10 mM, respectively? Answer: -5.93×10−6 kJPart C) If the processes described in parts A and B were coupled to ATP hydrolysis, how many moles of ATP would have to be hydrolyzed in order to make each process favorable? (Use the standard free energy change for ATP hydrolysis.)
the concentration of glucose inside a cell is 0.1 mM and the cell is suspended in a glucose solution of 0.01 mM: = [tex]5.93* 10^{-6} KJ[/tex]
Part A: Glucose concentration inside cell = 0.1 mm - concentration of glucose outside cell= 0.01 mm
Temperature = 2.73 + 37 = 310k
Gibb's free energy
ΔG = RT in {(Glucose)in/(Glucose)out }
= 8.314 J/molk * 310K * ln (0.1/0.001) = 5934.54 J/mol
Energy transported = (5934.54J/mol [tex]* 10^{-6}[/tex] mol)
= (5.93 [tex]* 10^{-6}[/tex] ) KJ
Part B: Glucose concentration in cell = 1 mm
Glucose concentration outside cell = 10 mm
Temperature = 273+37 = 310 K
Gibb's free energy
ΔG = RT ln {(glucose)in (glucose)out}
= 8.314 J/molK [tex]* 310 *[/tex] ln (0.1 mm/ 10.00 mm)
= -5934.54 J/mol
energy transported = (-5934.34.54 J/mol [tex]*[/tex] [tex]10^{-6}[/tex] ) moles
= (-5.934 [tex]* 10^{-6}[/tex] ) KJ
Part C:
ΔG of ArP hydrolysis = -32.2 KJ/mol
The mumber of moles of ATP formedis calculated =
moles of ATP = (-5.934[tex]* 10^{-6}[/tex] KJ/-32.2 KJ/mol )
= (1.84 [tex]* 10^{-7}[/tex] ) moles
to know more about glucose concentration click here:
https://brainly.com/question/3499336
#SPJ4
each of the compounds, a (ethanimine) and b (acetonitrile), protonates on nitrogen. draw the conjugate acid of each. select the strongest acid and the strongest base from the four species. compound a is c h 3 bonded to c h double bonded to n h where n has a lone pair. compound b is c h 3 bonded to c triple bonded to n, where n has a lone pair. draw the conjugate acid of compound a. draw the hydrogens. draw the conjugate acid of compound b. draw the hydrogens. identify the strongest acid: b ah bh a identify the strongest base. a ah b
Compound A's (ethanimine) conjugate acid will be CH3-CH=NH2+. Compound B's (acetonitrile) conjugate acid will be CH3-CNH2+.
What is called nitrogen?It is a colorless, flavorless, and odorless gas that makes up the majority of the atmosphere on Earth and is a component of all living things. Nitrogen is a chemical element with the symbol N and atomic number 7. Nitrogen is a nonmetal and the lightest element in the pnictogens, group 15 of the periodic table. It is a common element in the universe and is thought to be the eighth most abundant element overall in the Milky Way and the Solar System.
What is source of nitrogen?The primary source of nitrogen for atmospheric deposition is the combustion on fossil fuels like coal and oil. Nitrogen may be deposited in the atmosphere as dry particulates, gases, or droplets or as a wet form such as rainfall, snow, hail, fog, or freezing rain. Nitrogen primarily comes from the atmosphere. It is made comprised of this harmless, colorless gas in 78 percent of its composition.
Compound B (acetonitrile), which possesses a nitrogen atom with a higher positive charge and more electronegative properties that make it more stable after receiving a proton, is the strongest acid.
Compound A (ethanimine) has the strongest base because its nitrogen atom has a higher electron density and is better equipped to receive a proton.
To know more about Nitrogen visit:
https://brainly.com/question/16711904
#SPJ4
Both numbers have three
significant figures. How many
significant figures should be
recorded for the answer to the
division problem below?
43.6 +21.2
[?] significant figures
The number of significant figures that should be recorded for the answer will be only one which is 8.
What is Algebra?Algebra is the study of abstract symbols, while logic is the manipulation of all those ideas.
The acronym PEMDAS stands for Parenthesis, Exponent, Multiplication, Division, Addition, and Subtraction. This approach is used to answer the problem correctly and completely.
The numbers are 43.6 and 21.2. Then the addition of the numbers is given as,
⇒ 43.6 + 21.2
⇒ 64.8
The number of significant figures that should be recorded for the answer will be only one which is 8.
More about the Algebra link is given below.
https://brainly.com/question/953809
#SPJ1
Answer: 3
Explanation:
balance the following equation by fill-in in the blanks with whole numbers. make sure your equation is the smallest whole number ratio: h3po4 mg(oh)2 -> mg3(po4)2 h2o
The balance chemical equation is 2H₃PO₄ + 3Mg(OH)₂ → Mg₃(PO₄)₂ + 6H₂O
This is an example of an acid and base neutralizing one another to create salt and water. The reaction is exothermic, emits heat, and can be balanced by adding balancing numbers in front, or molecules, to make sure that the sum of the atom counts for each element on the left and right sides of the equation is the equal.
The law of conservation of matter, which stipulates that matter cannot be generated or destroyed, must be taken into account in order to balance a chemical equation.
H₃PO₄ + Mg(OH)₂ → Mg₃(PO₄)₂ + H₂O
This law states that whatever is available on the reactant side must also be available on the product side.
We must count the atoms on each side of the equation to balance it, and we might also use the number of moles.
The equation is balanced when
2H₃PO₄ + 3Mg(OH)₂ → Mg₃(PO₄)₂ + 6H₂O
Learn more about balance equation at https://brainly.com/question/16817698
#SPJ4
In lab you measure out 77.4 grams of C _5H_10O_5 for an experiment. How many mol is this? Give your answer to 2 decimal spaces
The number of moles of 77.4 grams of C₅H₁₀O₅ is 0.52 mol.
How many moles of C₅H₁₀O₅ do you have?
To determine the number of moles of C₅H₁₀O₅ in 77.4 grams, we need to divide the mass by the molar mass of the compound.
The molar mass of C₅H₁₀O₅ is:
5(12.01 g/mol) + 10(1.01 g/mol) + 5(16.00 g/mol) = 150.15 g/mol
So, the number of moles of C₅H₁₀O₅ in 77.4 grams is:
n = m/M = 77.4 g / 150.15 g/mol
n = 0.515 mol (rounded to 2 decimal spaces)
Therefore, 77.4 grams of C₅H₁₀O₅ is equivalent to 0.52 mol of C₅H₁₀O₅.
Learn more about moles here: https://brainly.com/question/15356425
#SPJ1
what is a molecule in a balanced equation?
In a balanced equation a molecule is made up of two or more atoms that have been chemically composed.
What do you mean by the term balanced equation ?The term balanced equation is defined as the mass of reactant is exactly similar to the mass of product in chemical reaction.
In a balanced equation two or more than two atoms are combined to produced molecule tha is also called as product. The right side of atoms known as reactant whereas the left side atoms or molecule are known as product.
Thus, Two or more than two atoms joined top formed molecule.
To learn more about the balanced equation, follow the link;
https://brainly.com/question/7181548
#SPJ9
Determine the mass fraction of hydrochloric acid obtained by merging 100 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 36% (density 1.180 g/cm3) and 50 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 20% (density 1.100 g/cm3)
Answer:
Solution:
1. Calculate the total volume of the two solutions:
Volume 1 = 100 cm3
Volume 2 = 50 cm3
Total Volume = 150 cm3
2. Calculate the total mass of each solution:
Mass of Solution 1 = (Volume x Density) x Mass Fraction HCl
= (100 cm3 x 1.180 g/cm3) x 0.36
= 43.2 g
Mass of Solution 2 = (Volume x Density) x Mass Fraction HCl
= (50 cm3 x 1.100 g/cm3) x 0.20
= 11 g
3. Calculate the total mass of the two solutions combined:
Total Mass = 43.2 g + 11 g
= 54.2 g
4. Calculate the mass fraction of hydrochloric acid in the new solution:
Mass Fraction HCl = Total Mass of HCl / Total Mass of Solutions
= 54.2 g / (43.2 g + 11 g)
= 0.55
Therefore, the mass fraction of hydrochloric acid obtained by merging 100 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 36%, and 50 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 20%, is 0.55.
drag each description to the appropriate target area to form the correct sequence of events that occurs when an action potential is generated. when all the descriptions have been placed, select the check answer button.
By dragging each description to the appropriate target area to form the correct sequence of events that occurs when an action potential is generated. when all the descriptions have been placed. Here discussion are done on the basis of sodium-potassium pumps
What is sodium channels?Mammals have two main kinds of sodium channels: the epithelial sodium channel and the voltage-gated sodium channel (VGSC) family (ESC). Different cell types in the body include voltage-gated sodium channels, although epithelial sodium channels are mostly found in the skin and kidney.
The correct order is as follows:
1) The axon is in its resting state. The interior is negative.
2) Sodium channels open
3) Sodium ions flow into the axon, making the interior positive.
4) Potassium channel open
5) Potassium ions flow out of the axon , making the interior negative
6) Sodium Potassium pumps restore the proper ion ratios.
To know more about Sodium Potassium pumps refer to:
https://brainly.com/question/1581552
#SPJ1
The complete question is as follows:
It says express the numeral, I’ve never heard about this and I’m rlly bad at math..
a. 7.623 × 10⁵ nm is expressed as 762300nm
b. 5.34 × 10⁻³ L is expressed as 0.00534
Following numerals are explain below:
What are numerals ?A numeral is a name or symbol that represents a certain number. Examples include the numerals three, four, and twelve. So, the numeral is how we express the number, which is a concept. Reason: A numeral is a word that describes a number, whereas a number is conveyed via digits.
c. 5.453 × 10⁶ m is expressed as 5453000
d. 6.791 × 10⁻⁵pm is expressed as 6791m
e. 2.4 × 10⁹pg is expressed as 2400000000
f. 3.65 × 10⁵ is expressed as 365000
g. 3.4287 × 10⁻⁶L is expressed as 0.0000034287
h. 9.2 × 10²mL is expressed as 920L
i. 6.927 × 10⁴ is expressed as 69270m
j. 9.23 × 10⁻³ is expressed as 0.00923
Thus, a. 7.623 × 10⁵ nm is expressed as 762300nm.
To learn more about numeral, follow the link;
https://brainly.com/question/21597658
#SPJ9
CAN SOMEONE HELP WITH THIS QUESTION?✨
Describe what happens to Copper Sulfate Pentahydrate when you heat it?
If the hydrate compounds are heated, they lose the water molecules by evaporation from their crystal lattice and they become anhydrous compounds. Thus, copper sulphate penta hydrate will form CuSO₄ solid on heating.
What are hydrates ?Hydrates are compounds with absorbed water molecules within their crystal lattice. The ability of absorption of moisture from the surrounding and form hydrates is called deliquescence.
Copper sulphate forms its various hydrates such as dihydrates, pentahydrates, hexahydrates etc. The hydrate Copper Sulfate Pentahydrate, CuSO₄. 5 H₂O contains 5 water molecules per one formula unit.
When this compound is heated, the water molecules will evaporate from the hydrate and become dry form called anhydrous. Thus, it will form anhydrous CuSO₄.
Find more on hydrates:
https://brainly.com/question/919417
#SPJ1
The change in boiling point for a solution is always:
Select the correct answer below:
added to the normal boiling point
subtracted from the normal boiling point
multiplied by the normal boiling point
depends on the solute
The change in the boiling point of a solution always depends on the solute.
What is boiling point?The boiling point is the temperature at which the vapor pressure of a liquid is equal to the external pressure experienced by the liquid. A liquid in a vacuum will have a lower boiling point than if it were under atmospheric pressure.
A solution has a higher boiling point than the pure solvent. This is because the solution must reach a temperature where the boiling pure solvent (eg water 100°C) must also exceed the boiling point of thore solute. So the boiling point of a solution depends on the solute.
Learn more about comparing the boiling points here :
https://brainly.com/question/2153588
#SPJ4
Whichof the following is the correct Newman projection for the following compound as viewed down the indicated bond in the conformttion shown? CH, TCH; CHj
The following is the correct Newman projection for the following compound as viewed down the indicated bond. The correct wedge and dash conformation for the following Newman projection is: IV
A Newman projection is a way of visualizing the conformation of a molecule around a single bond. The projection is created by looking directly down the bond axis, with one atom in front and one atom in back. The front atom is typically represented by a dot, and the back atom is usually hidden behind the front atom.
The 3D structure of organic molecules is depicted using the wedge and dash conformation. It is frequently used in organic chemistry to display how substituents are oriented around chiral centers. The atoms in this conformation are dots, and the bonds in the molecule are represented by lines. Dashes and wedges depict bonds entering and exiting the paper's or screen's plane, respectively.
Here you can learn more about A Newman projection
https://brainly.com/question/30651234
#SPJ4
Calculate the mass of water produced when 9.60 g of butane reacts with excess oxygen.
The mass of water produced when 9.60 g of butane reacts with excess oxygen is 14.85 gram.
What is combustion reaction ?The chemical reaction between substances, usually considering oxygen and usually accompanied by the generation of heat and light in the form of flame is called as combustion reaction.
C4H10(g) + 13 /2 O2(g) → 4CO2(g) + 5H2O(l)
Moles of butane = 9.60⋅g / 58.12⋅g⋅mol−1
= 0.165mol.
We assume complete combustion, and know that each mole of butane gives off 5 mol of water upon combustion.
Given that we know the molar quantity of butane, we simply perform the operation,
= 5 × 0.165 × 18.01
= 14.85 gram
Thus, the mass of water produced when 9.60 g of butane reacts with excess oxygen is 14.85 gram.
To learn more about the combustion reaction, follow the link;
https://brainly.com/question/30562669
#SPJ9