Question 7 of 15
Assuming all the substances below have the same mass, which substance
below requires the most energy to raise its temperature by 7°C? Use the table
to help you answer the question.
Substance
Air
Gold
Granite
Wood
Specific Heat
J/(kg °C)
1,010
130
800
1,760

A polymer of ten monomers contains nine bonds between monomers, we need nine water molecules to break all of these bonds and completely hydrolyze the polymer.

The number of water molecules needed to hydrolyze a polymer of a different length will vary and will depend on the number of monomers in the polymer.To calculate the number of water molecules needed to completely hydrolyze a polymer that is ten monomers long, we need to consider that each hydrolysis reaction involves the addition of one water molecule to break the bond between each monomer.

Since a polymer of ten monomers contains nine bonds between monomers, we need nine water molecules to break all of these bonds and completely hydrolyze the polymer.

However, we must also consider that an additional water molecule is needed to break the bond between the final monomer and the rest of the polymer chain. Therefore, a total of ten water molecules are needed to completely hydrolyze a polymer that is ten monomers long.

It is important to note that the number of water molecules needed to hydrolyze a polymer of a different length will vary and will depend on the number of monomers in the polymer.

Find out more about monomers

brainly.com/question/30629782

#SPJ4

The element that has the lowest first ionization energy is Fr that is francium.

The ionization energy is the measure of the capability of the element to enter into the chemical reactions that requiring the ion formation or the donation of the electrons. It is the  measure of the tendency in removing the electron from an atom or the ion.  The loss of the electron usually occurs in the ground state of a chemical species. The ionization energy will decreases from top to the bottom in groups, and will increases from the left to the right across a period.

Thus, the Fr element has the lowest first ionization energy.

This question is incomplete , the complete question is :

What element has the lowest first ionization energy? (F), (Li), (Fr), (Rb)?

To learn more about ionization energy here

https://brainly.com/question/28385102

#SPJ4

A hydrogen bond is a type of non-covalent bond that occurs between a hydrogen atom covalently bonded to an electronegative atom (such as oxygen, nitrogen, or fluorine) and another electronegative atom.

A hydrogen bond is formed when an electronegative atom attracts a hydrogen atom that is partly positive and partially negative. This electrostatic attraction can happen between molecules or inside a single molecule, and it causes a reasonably strong, directed connection between the two atoms. Hydrogen bonds are crucial for many biological processes, including the folding of proteins and the construction of the DNA double helix, and they also greatly influence the physical and chemical characteristics of liquids like water. an electrostatic attraction between a hydrogen atom in one polar (such as water's) molecule and a tiny electronegative (such as oxygen, nitrogen, or fluorine) atom in typically another polar (such as water's) or non-polar (such as nitrogen) molecule.

For such more questions on hydrogen bond:

brainly.com/question/10904296

#SPJ4

The volume of the unit cell for tantalum is 3.6259391x10⁻²³ cm³.

The smallest depiction of a complete crystal is called a unit cell. The volume of a unit cell can be calculated by finding the cube of the edge length. Since the edge length of the unit cell for tantalum is 331 pm, we can find the volume by cubing this value:

Volume = (edge length)³ = (331 pm)³ = 36,259,391 pm³

To convert from pm³ to cm³, we can use the conversion factor 1.00x10¹⁰ pm per 1.00 cm:

Volume = 36,259,391 pm³ × (1.00 cm / 1.00x10¹⁰ pm)³ = 3.6259391x10⁻²³ cm³

Therefore, the volume of the unit cell for tantalum is 3.6259391x10⁻²³ cm³.

To learn more about edge length; click here:

brainly.com/question/11796119

#SPJ11

To prepare 10.0 ml of a 0.25% m/v HCl solution, you will need to mix 2.5 ml of 1% m/v HCl solution with 7.5 ml of distilled water.

To make 10.0 ml of a 0.25% m/v HCl solution from 1% m/v HCl, dilute the 1% m/v HCl solution by a factor of 4.

Here's how to figure out how much 1% m/v HCl and distilled water you'll need:

Determine the concentration of HCl in the final solution:

A 0.25% m/v HCl solution contains 0.25 grams of HCl per 100 mL. 

As a result, there will be 0.25 g/100 ml x 10 ml = 0.025 g of HCl in 10 ml of solution.

Determine the quantity of 1% m/v HCl required:

1% m/v HCl implies that there is one gram of HCl in every 100 ml of solution. You will need the following to make 0.025 g of HCl:

0.025 g/1 g x 100 ml = 2.5 ml of 1% m/v HCl solution

Determine the amount of distilled water required:

To prepare the remaining 7.5 ml of solution, use the following :

10 ml - 2.5 ml = 7.5 ml of distilled water

For more such questions on solution, click on:

https://brainly.com/question/23269908

#SPJ4

The molar mass of AlCl₃ is 133.34 g/mol.

To calculate the molar mass of AlCl3, you need to know the atomic masses of aluminum (Al) and chlorine (Cl).

The atomic mass of Al is 26.98 g/mol and the atomic mass of Cl is 35.45 g/mol.

To find the molar mass of AlCl₃, you need to multiply the atomic mass of Al by the number of Al atoms in the compound (1) and add it to the atomic mass of Cl multiplied by the number of Cl atoms in the compound (3).

Molar mass of AlCl3 = (1 x 26.98 g/mol) + (3 x 35.45 g/mol) = 133.34 g/mol

To know more about AlCl₃ here:

https://brainly.com/question/16021551#

#SPJ11

The empirical formula for this oxide is NO.To determine the empirical formula for an oxide that contains 46.68% nitrogen, we need to find the ratio of nitrogen to oxygen in the compound.

Assuming a 100 g sample of the oxide, 46.68 g of it will be nitrogen, and the remaining 53.32 g will be oxygen.

Next, we need to convert these masses to moles. The atomic weight of nitrogen is 14.01 g/mol, and the atomic weight of oxygen is 16.00 g/mol. Therefore, we have:

Moles of nitrogen = 46.68 g / 14.01 g/mol = 3.33 mol

Moles of oxygen = 53.32 g / 16.00 g/mol = 3.33 mol

This shows that the ratio of nitrogen to oxygen in the oxide is 1:1. Therefore, the empirical formula for this oxide is NO.

Find  more about empirical formula

brainly.com/question/14846610

#SPJ4

The best practice when placing test tubes in a centrifuge is to balance the load.

To do this, place the test tubes on opposite sides of the rotor or bucket and evenly distribute the weight of the samples. Additionally, make sure to secure the lids of the test tubes with tape.

This will help prevent any of the samples from spilling during the centrifugation process and potentially damaging the centrifuge. Additionally, it is important to ensure that the test tubes are not touching each other, as this can also cause them to spill.

For more questions like Centrifuge click the link below:

https://brainly.com/question/14865029

#SPJ4

Ionization energy is the amount of energy required to remove an electron from a gaseous atom or ion. The ionization energy generally increases as you move from left to right across a period.

It is a periodic trend, meaning it changes in a predictable way as you move across the periodic table. This is because the nuclear charge increases, which means the electrons are more strongly attracted to the nucleus and more energy is required to remove them.

The ionization energy generally decreases as you move down a group. This is because the atomic radius increases, which means the electrons are further away from the nucleus and less energy is required to remove them.

In summary, the periodic trend of ionization energy is that it increases from left to right across a period and decreases from top to bottom down a group.

To know more about Ionization energy here:

https://brainly.com/question/28385102#

#SPJ11

The sulfur hexafluoride SF6  molecule is nonpolar and contains no lone (unshared) electron pairs on the sulfur atom.

Polar - A polar covalent link is created when atoms with different electronegativities share electrons to form a covalent bond. Polar bonding have a high melting point, low vapour pressure, high surface tension, and low boiling point. Polar chemicals interact with one another. On opposite ends of these molecules, there are positive and negative charges. They have electrical charge as a result. Examples include alcohol and sulphur.

Nonpolar: A non-polar covalent connection, a type of chemical bond, is produced when two atoms share electrons equally. Nonpolar bonding have high vapour pressure, low surface tension, low boiling points, and low melting points. Nonpolar molecules have no abundance of charges at their opposite ends and do not interact with other nonpolar molecules. Examples include pentane and carbon dioxide.

know more about polar and non polar click here;

https://brainly.com/question/30267810

#SPJ4

The following pairs are showing the types of bonds as follows:

1: N and H -  Moderately to very polar covalent

2: F and F - Nonpolar covalent

An enduring attraction between atoms or ions known as a chemical bond is what allows molecules and crystals to form.

Ionic, covalent, hydrogen, and van der Waals interactions are the four types of chemical bonding that are necessary for life to exist.

3: Li and F - ionic bond

4: Al and Cl - Very polar covalent

5: H and Br - Moderately polar covalent

6: S and F - Very polar covalent

7: C and O - Moderately to very polar covalent

8: Li and O - Ionic

9: Cl and F - Moderately polar covalent

10: Br and Br - Nonpolar covalent

To learn more about the chemical bond, follow the link;

https://brainly.com/question/15444131

#SPJ9

Generally, body fluid pH is strictly maintained by efflux across plasma membrane, buffering systems and acid excretion.

We can define, a buffer system as a solution which generally resists a change in pH when acids or bases are added. Basically, acidic solutions contain high concentrations of hydrogen ions (H+) and have pH values less than seven.

Generally, the transport across the plasma membrane occurs unaided through simple diffusion, i.e., molecules of gases such as carbon dioxide and oxygen, as well as small molecules like ethanol, enter the cell by crossing the cell membrane without any type of the assistance of any permease.

Generally in renal physiology, net acid excretion (NAE) is defined as the net amount of acid excreted in the urine per unit time. The value of NAE depends upon the flow rate of the urine.

Learn more about pH balance from the link given below.

https://brainly.com/question/3308661

#SPJ4

The items needed to run the spectrophotometry experiment are the correct option is  A. Spectrophotometer C. Blank solution D. Sample solution E. Cuvette F. Stir bar.

The spectrophotometer is the instrument that is used to measure the amount of the light the sample absorbs. This will work by passing the beam of the light through the sample to measure the intensity of the light of the sample. The instrument are used to measure the color and is used to monitoring the color.

The spectrophotometer is used to in the variety of the spectroscopy experiment such to determine the wavelength of the peak.

To learn more about spectrophotometer here

https://brainly.com/question/30576124

#SPJ4

The amount of energy required to remove an electron from an isolated atom or molecule is Ionisation energy.

Also  called as ionization potential, ionization energy is characterized as the aggregate sum of energy expected to free an electron, which is spinning in the peripheral shell of any molecule. On the other hand, scientific experts likewise characterize it as the complete energy expected to free one mole of electrons, from one mole of a specific iota.

In material science, we favor utilizing electron volts (eV) per iota, as a unit for ionization potential, while in science, it's deliberate with regards to kJ/mol (Kilojoules per mole). For instance, the ionization energy of hydrogen is 13.5984 eV. The lower the energy, higher is the inclination of a molecule to turn into a decreasing specialist and more receptive it is. Then again, higher the ionization energy, higher is the propensity to turn into an oxidizing specialist and less receptive it is.

To know more about Ionsiation energy,visit here:

https://brainly.com/question/20658080

#SPJ4

(Complete question) is:

the amount of energy required to remove an electron from an isolated atom or molecule is ______.

Interacting systems of molecules enclosed in compartments called cells evolved 3.8 billion years ago in living organisms.

In the field of biology, the smallest unit that is capable of surviving on its own and that is responsible for the formation of all living organisms and the tissues of the body. The cell membrane, the nucleus, and the cytoplasm are the three primary components that make up a cell. There are two categories of cells: eukaryotic, which have a nucleus, and prokaryotic, which do not have a nucleus but do have a nucleoid area. Eukaryotic cells are the more complex of the two. Eukaryotic species can be either single-celled or multicellular, but prokaryotic organisms always consist of a single cell.

To learn more about cells, click here:

https://brainly.com/question/11579425

#SPJ4

Answer:C

Explanation:

When water is barely boiling, it means the temp isn't the high at all. Answer A means it's boiling at a very high temp. And yeah I hope its right.

The pot that has the lowest temperature is the one that is just barely boiling. This means that it has not yet reached its boiling point and its temperature is likely below 100°C. The correct answer is C.

When water is boiling, it means that it has reached its boiling point or we can say that the water is transitioning from a liquid state to a gaseous state. We know that the boiling point of water is about 100°C or 212°F at standard pressure (atmospheric).

Learn more about definition and calculation of boiling point on:

One example of a tetrahedral, polar molecule with both polar and nonpolar covalent bonds is CHCl3, also known as chloroform.

A Lewis structure, also known as a Lewis dot diagram or electron dot diagram, is a simplified representation of the valence electrons in an atom or molecule. The Lewis structure shows how the valence electrons are arranged around the atoms in the molecule, as well as the bonds that form between the atoms. Valence electrons are the outermost electrons in an atom, and they are responsible for the chemical properties of the element. In a Lewis structure, each valence electron is represented by a dot or cross, which is placed around the symbol of the element. The dots are arranged around the element symbol to represent the number of valence electrons, with each side of the symbol representing one of the four possible energy levels.

Here,

In this structure, the carbon atom is at the center, with four electron pairs around it: one from each of the three chlorine atoms and one from the hydrogen atom. The carbon-chlorine bonds are polar covalent bonds because chlorine is more electronegative than carbon, meaning it attracts electrons more strongly and creates a partial negative charge. The carbon-hydrogen bonds are nonpolar covalent bonds because carbon and hydrogen have similar electronegativities, meaning they share electrons equally and do not create partial charges. As a result of the polar and nonpolar covalent bonds, the molecule as a whole is polar, with a partial positive charge on the hydrogen atom and partial negative charges on the chlorine atoms.

Cl      Cl

 \      /

  C -- H

  |

  Cl

To know more about Lewis structure,

https://brainly.com/question/24076507

#SPJ1

Option E: HDL, or high-density lipoprotein, is the lipoprotein that contains the most cholesterol which means that they contain high amounts of cholesterol.

HDL stands for high-density lipoprotein. One of the five main categories of lipoproteins, known as good cholesterol, allows lipids (fats) like cholesterol to be carried within the bloodstream. The beneficial cholesterol is known as high-density lipoprotein (HDL).

These are proteins that assist them in performing particular tasks. In particular, reverse cholesterol transport—the process of moving lipids from tissues to the liver—is one of the vital functions of lipoproteins in the body. The body eliminates extra cholesterol from the tissues and transports it back to the liver during reverse cholesterol transport.

To know more about lipoproteins, refer:

https://brainly.com/question/16170788

#SPJ4

The collection of 1.25 * 10⁻¹⁹  electrons has a total charge of approximately -2.003 coulombs.

The charge of a single electron is approximately -1.602 * 10⁻¹⁹ coulombs. To find the total charge of a collection of electrons, we can multiply the number of electrons by the charge of each electron.

So, for a collection of 1.25 * 10⁻¹⁹  electrons, the total charge would be:

Q = (1.25 * 10⁻¹⁹ ) (-1.602 * 10⁻¹⁹)C/electron

Q = -2.003 C

Therefore, the collection of 1.25 * 10⁻¹⁹  electrons has a total charge of approximately -2.003 coulombs.

The coulomb (symbol: C) is the unit of electric charge in the International System of Units (SI). It is defined as the amount of electric charge transported in one second by a constant current of one ampere.

Learn more about electron charge here brainly.com/question/14494965

#SPJ4

The molecular geometry of H₃O⁺ is trigonal pyramidal.

The H3O+ ion is also known as the hydronium ion. It is formed when a water molecule (H₂O) gains an extra proton (H⁺). It plays an essential role in acid-base chemistry and is commonly encountered in aqueous solutions.

In the trigonal pyramidal geometry, the three hydrogen atoms form a pyramid around the oxygen atom. The bond angles between the hydrogen atoms are approximately 109.5 degrees. The lone pair of electrons occupies one of the four electron domains around the oxygen atom, giving it a trigonal pyramidal shape.

Learn more about molecular geometry, here:

https://brainly.com/question/31993718

#SPJ6

the number of grams of oxygen that are produced from the decomposition of 100g of kclo3 is 39.14 grams.

The balanced chemical equation for the decomposition of potassium chlorate (KClO3) is:

2KClO3(s) -> 2KCl(s) + 3O2(g)

According to this equation, 2 moles of KClO3 will produce 3 moles of O2.

The molar mass of KClO3 is approximately 122.55 g/mol, so 100 g of KClO3 is equivalent to 100/122.55 = 0.815 moles of KClO3.

Using the mole ratio from the balanced equation, we can calculate the number of moles of O2 produced:

0.815 moles KClO3 x (3 moles O2 / 2 moles KClO3) = 1.223 moles O2

Finally, we can calculate the mass of O2 produced using its molar mass, which is approximately 32 g/mol:

1.223 moles O2 x 32 g/mol = 39.14 g of O2

Therefore, approximately 39.14 grams of oxygen can be produced from the decomposition of 100 g of KClO3.

Learn more about decomposition here:

https://brainly.com/question/8009068

#SPJ4

A good scientific experiment is reproducible. It means that same result is achievable with high accuracy and precision.

Reproducibility, otherwise called replicability and repeatability, is a significant guideline supporting the logical strategy. For the scientific experiments to be reproducible implies that results got by an examination or an observational review or in a measurable examination of an informational index ought to be accomplished again with a serious level of unwavering quality when the review is imitated. There are various types of replication yet commonly replication studies include various scientists utilizing a similar system. Solely after one or a few such fruitful replications should an outcome be perceived as logical information.

With a smaller degree, reproducibility has been presented in computational sciences: Any outcomes ought to be recorded by making all information and code accessible so that the calculations can be executed again with indistinguishable outcomes.

To know more about experiment,visit here:

https://brainly.com/question/13184032

#SPJ4

The functional group of alcohol and phenol is the correct option is A) −OH Phenol and Alcohol.

The hydroxyl group that is ,- OH is found in the alcohol compound and the phenol as the functional groups. Alcohols and the phenols are classified in to the  mono–, di–, tri- or the polyhydric compounds . This is based on the one, two , the three or the many hydroxyl groups.

The Alcohols are the mostly colorless, and alcohols are usually exist in the state of the liquid state. The Phenols are the colorless solids which is usually exist in the form of the  crystals at the STP.

To learn more about alcohol here

https://brainly.com/question/30408740

#SPJ4

Press 2+5bUiR1(: r)p to change a complex number into polar form. Use the r theta command or enter the angle in polar form to convert any complex number's polar form.

Most scientific calculators have a function to convert a complex number from rectangular form (a + bi) to polar form (r cis θ). Here's how to do it:

1) Enter the complex number in rectangular form into your calculator using the "a + bi" format.

2) Press the "mode" or "setup" button on your calculator and select "polar" or "cis" mode.

3) Press the "convert" or "pol" button on your calculator to convert the complex number to polar form. The result will be displayed in the format "r cis θ".

4) If your calculator displays the polar form in radians, you may need to convert it to degrees if you need it in degrees. To do this, multiply the angle in radians by 180/π.

Alternatively, you can manually convert a complex number from rectangular to polar form using the following formulas:

r = √(a² + b²)

θ = atan(b/a)

where a is the real part and b is the imaginary part of the complex number. The angle θ is measured in radians, and atan() is the inverse tangent function.

To learn more about complex number :

https://brainly.com/question/20566728

#SPJ4

The statement is true, because, When a non-volatile solute is added to a solvent, it reduces the tendency of the solvent molecules to escape into the gas phase and form vapor.

This is because the solute particles obstruct the surface of the solvent and reduce the surface area available for evaporation. As a result, the rate of evaporation decreases, and fewer solvent molecules escape into the vapor phase.

This effect is described by Raoult's law, which states that the vapor pressure of a solvent above a solution is lower than the vapor pressure of the pure solvent due to the presence of non-volatile solutes.

Learn more about non-volatile solute:

https://brainly.com/question/26414694

#SPJ4

The balanced chemical equation of the combustion reaction of C₁₆H₃₄ is given below. The heat of combustion of the reaction is - 10699 kJ/mol.

[tex]\rm C_{16}H_{34} + \frac{49}{2} O_{2} \rightarrow 16CO_{2} + 17 H_{2}O[/tex]

Combustion is a type of reaction, in which a gas or liquid burns in oxygen to give carbon dioxide and water. Combustion is an exothermic reaction. Hence, it evolves heat to the surroundings. The enthalpy of combustion is always negative.

Hydrocarbons gases such as gasoline easily undergo combustion and they can be used as fuels in vehicles where the chemical energy is converted to the mechanical energy.

Here, the given hydrocarbon is C₁₆H₃₄. To balance the combustion reaction. First balance the number of oxygen and hydrogen as in the number of the gas. Then balance the number of oxygen as written below:

[tex]\rm C_{16}H_{34} + \frac{49}{2} O_{2} \rightarrow 16CO_{2} + 17 H_{2}O[/tex]

Find more on combustion:

https://brainly.com/question/15117038

#SPJ1

Ethan have to push with more force on table A than on table B because of the heavy mass of table A.

When applied, force generally defined as a external cause that alters or tends to modify the condition of the body. If indeed the body is moving this will come to rest, as well as if it is at rest, it will move. It can also induce changes in the body's orientation, form, size, and so on.

Ethan is helping his father rearrange the furniture in their living room. They have two different tables that are the same size. When Ethan pushes on each table, he finds that it is harder to move table A than it is to move table B. Ethan have to push with more force on table A than on table B because of the heavy mass of table A.

Therefore, ethan have to push with more force on table A than on table B because of the heavy mass of table A.

To learn more about force, here:

https://brainly.com/question/13014979

#SPJ9

Answer: Table A has more mass than table B.