QUESTION 9 The Falkirk Wheel makes ingenious use of a. Fermat's Principle b. Pascal's Principle c. Bernoulli's Principle d. The Principle of Parsimony e. Archimedes' Principle QUESTION 10 The approximate mass of air in a Boba straw of cross sectional area 1 cm2 that extends from sea level to the top of the atmosphere is a 1000 kg 6.0.1 kg c. 10 kg d. 1 kg e. 100 kg

Answers

Answer 1

Answer to Question 9: The Falkirk Wheel makes ingenious use of Archimedes' Principle.

Answer to Question 10: The approximate mass of air in a Boba straw of cross-sectional area 1 cm2 that extends from sea level to the top of the atmosphere is 10 kg.

The mass of the air in the straw can be calculated by first finding the height of the atmosphere. The atmosphere is approximately 100 km in height. The density of air at sea level is 1.2 kg/m3, and it decreases exponentially with height. Integrating the density over the height of the straw gives the mass of air, which is approximately 10 kg. This calculation assumes that the temperature and pressure are constant along the height of the straw, which is not entirely accurate but provides a rough estimate.

learn more about atmosphere here:

https://brainly.com/question/31406689

#SPJ11


Related Questions

023-kg satellite orbits the Earth at a constant altitude of 92-km. a. How much energy must be added to the system to move the satellite into a circular orbit with altitude 210 km? b. What is the change in the system's kinetic energy? c. What is the change in the system's potential energy?

Answers

We need to add 1.63 × 10^8 J of energy to the system to move the satellite into a circular orbit with altitude 210 km. The change in kinetic energy is   ΔK = 1.63 × 10^8 J. The change in potential energy is -1.63 × 10^8 J.

To move the satellite into a circular orbit with an altitude of 210 km, we need to add energy equal to the difference in potential energy between the initial and final orbits.

The potential energy of a satellite in orbit is given by U = -GMm/r, where G is the gravitational constant, M is the mass of the Earth, m is the mass of the satellite, and r is the distance between the centers of mass of the Earth and the satellite.

Since the mass of the satellite remains constant, the change in potential energy is equal to ΔU = U_final - U_initial = -GMm(1/r_final - 1/r_initial). Plugging in the given values, we get: ΔU = - (6.674 × 10^-11 Nm²/kg²) (5.98 × 10^24 kg) (0.023 kg) [1/(6,711,000 m) - 1/(6,982,000 m)] . ΔU = 1.63 × 10^8 J.

The change in kinetic energy of the satellite is equal to the work done on it, which is the same as the energy we added to the system in part (a).

To know more about kinetic energy, refer here:

https://brainly.com/question/30764377#

#SPJ11

Aromatic molecules like those in perfume have a diffusion coefficient in air of approximately 2×10−5m2/s. Estimate, to one significant figure, how many hours it takes perfume to diffuse 2.0 m , about 5 ft , in still air.

Answers

It takes approximately 56 hours (to one significant figure) for perfume to diffuse a distance of 2.0 m (about 5 ft) in still air.

What is a diffusion coefficient?

First, we need to understand the concept of diffusion coefficient. It is a measure of how quickly a substance diffuses (spreads out) through a medium, such as air. In the case of perfume, the diffusion coefficient in air is given as 2×10−5m2/s. This means that, on average, a perfume molecule will travel a distance of √(2×10−5m^2) = 0.0045 m (about 4.5 mm) in one second.

To estimate the time required for perfume to diffuse a distance of 2.0 m in still air, we use Fick's law of diffusion, which relates the diffusion distance, diffusion coefficient, and time:

Diffusion distance = √(Diffusion coefficient × time)

Rearranging this equation, we get:

Time = (Diffusion distance)^2 / Diffusion coefficient

Substituting the given values, we get:

Time = (2.0 m)^2 / (2×10−5 m^2/s)

Time = 200000 s = 55.6 hours (approx.)

Therefore, it takes approximately 56 hours (to one significant figure) for perfume to diffuse a distance of 2.0 m (about 5 ft) in still air.

Note that this is only an estimate, as the actual time required for perfume to diffuse a certain distance in air depends on various factors, such as temperature, pressure, and air currents. Also, the actual diffusion process is more complex than what is captured by Fick's law, as it involves multiple factors such as the size, shape, and polarity of the perfume molecules, as well as interactions with air molecules. Nonetheless, the above calculation provides a rough idea of the time required for perfume to diffuse in still air.

Learn more about diffusion

brainly.com/question/20843145

#SPJ11

The specific tension of muscle is about 30 N/cm^2. The cross-sectional areas of the prime movers for elbow flexion and extension have been measured as follows:
Muscles Cross-sectional area
Biceps brachii 3.6 cm2
Brachialis 6.0 cm2
Brachioradialis 1.5 cm2
Triceps brachii 17.8 cm2
A. Determine the maximum force that the elbow flexors (as a group of muscles) can exert.
B. Consider the elbow flexors to act together with a moment arm of 4 cm, and the triceps with a moment arm of 2.5 cm. If all of these muscles were activated fully, would the elbow flex or extend?

Answers

A. We need to compute the entire cross-sectional area of the prime movers for elbow flexion and multiply it by the specific tension of muscle to get the maximum force that the elbow flexors can produce. The elbow flexors have a total cross-sectional area of 3.6 + 6.0 + 1.5 = 11.1 cm2. As a result, the elbow flexors may exert the following amount of force:

Cross-sectional area times a certain tension equals force.

Force = 333 N Force = 11.1 cm2 x 30 N/cm2

B. We must compare the torques generated by the triceps and the elbow flexors in order to determine whether the elbow will flex or extend. A muscle's torque is determined by multiplying the force it exerts by the moment arm. The moment arm is the angle at which the muscle's line of action is perpendicular to the axis of rotation.

The total torque for the elbow flexors is:

Torque equals force times moment arm

Torque equals 333 N/4 cm.

1332 N cm of torque

The total torque for the triceps is:

Torque equals force times moment arm

Torque is equal to 17.8 cm2 x 30 cm2 x 2.5 cm.

1335 N cm of torque

Since the triceps generate slightly more torque than the elbow flexors do, the elbow would extend if all of these muscles were fully engaged.

For more such questions on elbow

https://brainly.com/question/13746212

#SPJ11

A. To determine the maximum force that the elbow flexors can exert, we need to calculate the total cross-sectional area of the prime movers for elbow flexion, and then multiply it by the specific tension of the muscle:

The total cross-sectional area of elbow flexors = Biceps brachii + Brachialis + Brachioradialis

= 3.6 cm2 + 6.0 cm2 + 1.5 cm2

= 11.1 cm2

The maximum force that the elbow flexors can exert = Total cross-sectional area x Specific tension of muscle

= 11.1 cm2 x 30 N/cm2

= 333 N

Therefore, the maximum force that the elbow flexors can exert is 333 N.

B. To determine whether the elbow would flex or extend if all of these muscles were activated fully, we need to calculate the net torque generated by the muscles:

Net torque = (Force x Moment arm)flexors - (Force x Moment arm)triceps

Where force is the maximum force that the elbow flexors can exert (333 N), the moment arm of the elbow flexors is 4 cm, and the moment arm of the triceps is 2.5 cm.

Net torque = (333 N x 4 cm) - (333 N x 2.5 cm)

= 999 Ncm - 832.5 Ncm

= 166.5 Ncm

Since the net torque is positive (166.5 Ncm), the elbow would flex if all of these muscles were activated fully.

Learn more about cross-sectional area, here:

brainly.com/question/30395236

#SPJ11

The following data of position x and time t are collected for an object that starts at rest and moves with constant acceleration. x(m) 0 2 1 5 2 14 3 29 The position of the object at t = 5s is most nearly A 30m B 45m с 75m D 77m E 110m

Answers

The position of the object at t = 5s is most nearly D) 77m.

The given data shows the position x of an object at different times t, assuming it starts from rest and moves with constant acceleration. To find the position of the object at t = 5s, we can use the equation of motion x = ut + (1/2)at², where u is the initial velocity (which is zero in this case) and a is the acceleration (which is constant).

Using the given data, we can calculate the acceleration of the object by taking the difference in position and time for each pair of consecutive data points. We get:

a = (2-0)/(2-0) = 1 m/s²a = (5-1)/(3-2) = 4 m/s²a = (14-5)/(2-1) = 9 m/s²a = (29-14)/(3-2) = 15 m/s²

Now we can use the equation of motion with the calculated acceleration to find the position of the object at t = 5s:

x = 0 + (1/2)15(5²) = 75m (rounded to the nearest integer)

Therefore, the position of the object at t = 5s is most nearly D) 77m.

To learn more about acceleration, here

https://brainly.com/question/12550364

#SPJ4

An ideal gas is compressed isobarically to one-third of its initial volume. The resulting pressure will be?A) three times as large as the initial value. B) equal to the initial value. C) more than three times as large as the initial value. D) nine times the initial value. E) impossible to predict on the basis of this data.

Answers

The correct answer is three times as large as the initial value .option (A)

The given scenario describes the process in which an ideal gas is compressed isobarically, which means that the pressure remains constant during the compression process. The process, however, results in a change in the volume of the gas.

According to Boyle's Law, at a constant temperature, the product of pressure and volume of a gas remains constant. Mathematically,

P₁V₁ = P₂V₂

Where P₁ and V₁ are the initial pressure and volume of the gas, respectively, while P₂ and V₂ are the final or resulting pressure and volume of the gas.

In the given scenario, the volume of the gas is compressed to one-third of its initial volume (V₂ = 1/3 V₁). Therefore, using Boyle's Law, we can write:

P₁V₁ = P₂(1/3 V₁)

Simplifying the above equation, we get:

P₂ = 3P₁

This means that the resulting pressure (P₂) will be three times the initial pressure (P₁), independent of the actual value of P₁. Therefore, the correct answer is option A) three times as large as the initial value.

For such more questions on initial

https://brainly.com/question/28336431

#SPJ11

the intensity at a certain location is 1.054 w/m2. what is the sound intensity level at this location, in db?

Answers

The sound intensity level at this location, in db is 120.23 dB.

To find the sound intensity level in decibels (dB) at a location with an intensity of 1.054 W/m², you can use the following formula:

Sound Intensity Level (dB) = 10 * log10(I/I₀)

where I is the intensity at the location (1.054 W/m²) and I₀ is the reference intensity (10⁻¹² W/m²). Now let's plug in the values and calculate the sound intensity level.

Step 1: Substitute the values into the formula
Sound Intensity Level (dB) = 10 * log10(1.054 / 10⁻¹²)

Step 2: Calculate the ratio inside the logarithm
1.054 / 10⁻¹² = 1.054 * 10¹² = 1.054 × 10¹²

Step 3: Calculate the logarithm of the ratio
log10(1.054 × 10¹²) ≈ 12.023

Step 4: Multiply the logarithm by 10
10 * 12.023 ≈ 120.23

120.23 dB is the sound intensity level at this location.

For more questions on sound intensity :

https://brainly.com/question/17062836

#SPJ11

The sound intensity level at this location, in dB, given that intensity of the location is 1.054 W/m², is 120.23 dB

How do i determine the intensity in db?

The sound intensity level at the location can be obtained as illustrated below:

Intensity at the location (I) = 1.054 W/m²Reference intensity (I₀) = 10⁻¹² W/m²Sound intensity level = ?

Sound intensity level = 10 × log₁₀ (I/I₀)

Sound intensity level = 10 × log₁₀ (1.054 / 10⁻¹²)

Sound intensity level (in dB) = 120.23 dB

Thus, we can conclude fro the above calculation that the sound intensity level at the location is 120.23 dB

Learn more about sound intensity level:

https://brainly.com/question/29080003

#SPJ4

The conducting path between the right hand and the left hand can be modeled as a 12 cm-diameter, 180cm-long cylinder. The average resistivity of the interior of the human body is 4.7(Omega*m) . Dry skin has a much higher resistivity, but skin resistance can be made negligible by soaking the hands in salt water. If skin resistance is neglected, what potential difference between the hands is needed for a lethal shock of 100 mA across the chest? Your result shows that even small potential differences can produce dangerous currents when the skin is wet.

Answers

To calculate the potential difference needed for a lethal shock of 100 mA across the chest, we can use Ohm's law, which states that V = IR, where V is the potential difference, I is the current, and R is the resistance.

First, we need to find the resistance of the conducting path between the hands. We can use the formula for the resistance of a cylinder, which is R = (ρL) / A, where ρ is the resistivity, L is the length, and A is the cross-sectional area.

Using the given values, we get:

R = (4.7 Ω*m * 1.8 m) / [(π/4) * (0.12 m)^2]
R = 3.1 Ω

This is the resistance of the conducting path between the hands, assuming skin resistance is negligible.

To know more about resistivity visit

https://brainly.com/question/30799966

#SPJ11

A small particle has charge -5.00 uC and mass 2.00 x 10^-4 kg. It moves from point A where the electric potential is VA= +200.0 Volts, to point B, where the electric potential is VB= +800.0 Volts. The electric force is the only force acting on the particle. The particle has a speed of 5.00 m/s at point A.
What is the speed at Point B?

Answers

The speed of a charged particle with a charge of -5.00 uC and mass of 2.00 x 10⁻⁴ kg moving from point A to point B with an electric potential difference of +600.0 V is 117.8 m/s at point B.

Using conservation of energy, we can equate the initial kinetic energy of the particle with the final kinetic energy plus the change in potential energy. The formula for potential energy is qV, where q is the charge of the particle and V is the potential difference.

[tex]KE_{\text{initial}} = \frac{1}{2} m v_A^2[/tex]

[tex]KE_{\text{final}} = \frac{1}{2} m v_B^2[/tex]

[tex]\Delta U = q(V_B - V_A)[/tex]

Equating these, we get:

[tex]\frac{1}{2} m v_A^2 = \frac{1}{2} m v_B^2 + q(V_B - V_A)[/tex]

Solving for [tex]v_B[/tex], we get:

[tex]v_B = \sqrt{\left(v_A^2 + \frac{{2q(V_B - V_A)}}{m}\right)}[/tex]

Plugging in the given values, we get:

[tex]v_B = \sqrt{\left(5.00^2 + \frac{2 \cdot (-5.0010^{-6})(800 - 200)}{0.0002}\right)} = 117.8 \, \text{m/s}[/tex]

(rounded to three significant figures)

Therefore, the speed of the particle at point B is 117.8 m/s.

To know more about the speed of the particle refer here :

https://brainly.com/question/31184765#

#SPJ11

an object is located a distance of d0 = 15 cm in front of a concave mirror whose focal length is f = 11 cm.
Write an expression for the image distance di

Answers

The mirror formula is 1/f = 1/d0 + 1/di. Plug in f = 11 cm and d0 = 15 cm to find the image distance, di.


The mirror formula is a relationship between the focal length (f), the object distance (d0), and the image distance (di) in a concave mirror.

It is given by the formula:

1/f = 1/d0 + 1/di

In this problem, the object is located at a distance d0 = 15 cm in front of a concave mirror with a focal length of f = 11 cm.

To find the image distance (di), plug in these values into the mirror formula:

1/11 = 1/15 + 1/di

Now, you need to solve for di. With some algebraic manipulation, you'll find the value of di for this particular problem.

For more such questions on mirror, click on:

https://brainly.com/question/10848908

#SPJ11

The mirror formula is 1/f = 1/d0 + 1/di. Plug in f = 11 cm and d0 = 15 cm to find the image distance, di.

The mirror formula is a relationship between the focal length (f), the object distance (d0), and the image distance (di) in a concave mirror.

It is given by the formula:

1/f = 1/d0 + 1/di

In this problem, the object is located at a distance d0 = 15 cm in front of a concave mirror with a focal length of f = 11 cm.

To find the image distance (di), plug in these values into the mirror formula:

1/11 = 1/15 + 1/di

Now, you need to solve for di. With some algebraic manipulation, you'll find the value of di for this particular problem.

Visit to know more about Mirror:-

brainly.com/question/10848908

#SPJ11

a 15 kg runaway grocery cart runs into a spring with spring constant 240 n/m and compresses it by 60 cm .

Answers

The force exerted on the spring by the cart is 144 N. This force causes the spring to compress and store potential energy, which can be released when the spring is allowed to return to its original state.

When the 15 kg runaway grocery cart collides with the spring, the spring compresses due to the force exerted on it by the cart. The spring has a spring constant of 240 N/m, which means that for every meter the spring is compressed, it exerts a force of 240 N.

In this case, the spring is compressed by 60 cm or 0.6 meters. Therefore, the force exerted on the spring by the cart can be calculated using the equation F = kx, where F is the force, k is the spring constant, and x is the displacement.

Plugging in the values, we get:

F = 240 N/m x 0.6 m = 144 N

Overall, this scenario demonstrates the relationship between force, displacement, and spring constant, and how they can be used to calculate the energy involved in a collision or interaction between objects.

As the given question is incomplete, The complete question is "A 15 kg runaway grocery cart runs into a spring with a spring constant of 240 n/m and compresses it by 60 cm. Calculate the applied force."

You can learn more about spring constants at: brainly.com/question/14159361

#SPJ11

Define the linear transformation T: Rn → Rm by T(v) = Av. Find the dimensions of Rn and Rm. A = 0 5 −1 4 1 −2 1 1 1 3 0 0 dimension of Rn dimension of Rm

Answers

The linear transformation T: [tex]R^n[/tex] → [tex]R^m[/tex] with matrix A maps a vector of dimension n to a vector of dimension m, where the dimensions of R^n and R^m correspond to the input and output dimensions, respectively.

The matrix A is a 4x3 matrix, as it has 4 rows and 3 columns. Therefore, the transformation T: [tex]R^3[/tex] → [tex]R^4[/tex] takes a 3-dimensional vector as input and returns a 4-dimensional vector as output.

So the dimension of Rn is 3 (since Rn is the domain of T and T takes vectors in R^3) and the dimension of Rm is 4 (since Rm is the range of T and T returns vectors in [tex]R^4[/tex]).

The linear transformation T: [tex]R^n[/tex] → [tex]R^m[/tex], defined by T(v) = Av where A is an mxn matrix, maps a vector of dimension n to a vector of dimension m. In this case, the matrix A is a 4x3 matrix, meaning that the transformation T maps a 3-dimensional vector to a 4-dimensional vector.

Therefore, the dimension of [tex]R^n[/tex] is 3, as it represents the domain of T and T takes vectors of dimension n. Similarly, the dimension of [tex]R^m[/tex] is 4, as it represents the range of T and T returns vectors of dimension m.

Learn more about linear transformation: brainly.com/question/20366660

#SPJ11

An AC circuit has a capacitive reactance of 30 ohms in addition to an inductive reactance of 40 ohms connected in series. What is the total reactance of the circuit

Answers

The total reactance of the circuit is 10 ohms. In an AC circuit, the total reactance is the algebraic sum of the capacitive reactance (Xc) and the inductive reactance (Xl).

Given that the capacitive reactance is 30 ohms and the inductive reactance is 40 ohms, we can calculate the total reactance as follows:

Total reactance = Xc + Xl = 30 ohms + (-40 ohms) = -10 ohms.

Since the capacitive and inductive reactances have opposite signs, we need to consider their algebraic sum. Therefore, the total reactance of the circuit is 10 ohms. This indicates that the circuit has a net inductive reactance.

Learn more about reactance here:

https://brainly.com/question/31369031

#SPJ11

determine the rms value of the fundamental component of the line-line voltage.

Answers

The rms value of the fundamental component of the line-line voltage is 220V.

The rms value of the fundamental component of the line-line voltage can be calculated using the formula:
Vrms = Vpeak / √2
where Vpeak is the peak voltage of the fundamental component.
To find the peak voltage of the fundamental component, we need to know the voltage waveform. If the waveform is a sinusoidal voltage, the peak voltage can be found by multiplying the peak value of the sinusoidal voltage by √2.
For example, if the peak voltage of the sinusoidal voltage is 220V, then the peak voltage of the fundamental component would be:
Vpeak = 220V x √2 = 311.13V
Substituting this value into the formula for Vrms, we get:
Vrms = 311.13V / √2 = 220V
Therefore, the rms value of the fundamental component of the line-line voltage is 220V.

learn more about voltage

https://brainly.com/question/13521443

#SPJ11

a gaseous mixture contains 406.0 torr h2(g), 325.1 torr n2(g), and 66.3 torr ar(g). calculate the mole fraction, , of each of these gases.

Answers

The mole fraction of H2 is 0.509, the mole fraction of N2 is 0.408, and the mole fraction of Ar is 0.084.

To calculate the mole fraction of each gas, we need to use the following formula:

mole fraction of gas = moles of gas / total moles of gas

To find the moles of each gas, we need to use the ideal gas law equation:

PV = nRT

where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature in Kelvin.

We are given the pressure of each gas in torr, so we need to convert it to atm by dividing by 760 torr/atm. We can assume that the volume and temperature are constant for all the gases.

Calculations:

For H2 gas:

n(H2) = (406.0 torr / 760 torr/atm) * V / (0.0821 L*atm/mol*K * 298 K)

n(H2) = 0.0176 mol

For N2 gas:

n(N2) = (325.1 torr / 760 torr/atm) * V / (0.0821 L*atm/mol*K * 298 K)

n(N2) = 0.0141 mol

For Ar gas:

n(Ar) = (66.3 torr / 760 torr/atm) * V / (0.0821 L*atm/mol*K * 298 K)

n(Ar) = 0.0029 mol

The total moles of gas are:

n(total) = n(H2) + n(N2) + n(Ar)

n(total) = 0.0176 mol + 0.0141 mol + 0.0029 mol

n(total) = 0.0346 mol

Now we can calculate the mole fraction of each gas:

X(H2) = n(H2) / n(total) = 0.0176 mol / 0.0346 mol = 0.509

X(N2) = n(N2) / n(total) = 0.0141 mol / 0.0346 mol = 0.408

X(Ar) = n(Ar) / n(total) = 0.0029 mol / 0.0346 mol = 0.084

Learn more about fraction here:

https://brainly.com/question/10354322

#SPJ11

A sample of radioactive material with a half-life of 200 days contains 1×1012 nuclei. What is the approximate number of days it will take for the sample to contain 1.25×1011 radioactive nuclei?
A.) 200
B.) 400
C.) 600
D.) 800

Answers

The answer is C.) it will take approximately 600 days for the sample to contain 1.25×1011 radioactive nuclei.


The half-life of the radioactive material is 200 days, which means that after 200 days, half of the original nuclei will have decayed. So, after another 200 days (a total of 400 days), half of the remaining nuclei will have decayed, leaving 1/4 of the original nuclei.

We can set up an equation to solve for the time it will take for the sample to contain 1.25×1011 radioactive nuclei:

1×1012 * (1/2)^(t/200) = 1.25×1011

Where t is the number of days.

Simplifying this equation, we can divide both sides by 1×1012 and take the logarithm of both sides:

(1/2)^(t/200) = 1.25×10^-1

t/200 = log(1.25×10^-1) / log(1/2)

t/200 = 3

t = 600

Therefore, it will take 600 days for the sample to contain 1.25×1011 radioactive nuclei.

To learn more about half-life visit:

brainly.com/question/24710827

#SPJ11

A string is 50.0cm long and has a mass of 3.00g. A wave travels at 5.00m/s along this string. A second string has the same length, but half the mass of the first. If the two strings are under the same tension, what is the speed of a wave along the second string?

Answers

The speed of a wave along the second string is given by the expression √[(2 ˣ  T) / μ1], where T is the tension in the strings and μ1 is the linear mass density of the first string.

What is the speed of a wave along the second string if it has the same length but half the mass of the first string, and both strings are under the same tension?

To find the speed of a wave along the second string, we can use the equation v = √(T/μ), where v is the wave speed, T is the tension in the string, and μ is the linear mass density of the string.

Given that the first string has a length of 50.0 cm and a mass of 3.00 g, we can calculate its linear mass density:

μ1 = mass/length = 3.00 g / 50.0 cm

Now, since the second string has half the mass of the first but the same length, its linear mass density will be:

μ2 = (1/2) ˣ μ1

Since both strings are under the same tension, we can assume the tension is constant, denoted as T.

Now, let's calculate the wave speed along the second string:

v2 = √(T/μ2)Substituting the expression for μ2:v2 = √(T / [(1/2) ˣ μ1])Simplifying further:v2 = √[(2 * T) / μ1]

Therefore, the speed of a wave along the second string is given by √[(2 ˣ T) / μ1], where T is the tension in the strings and μ1 is the linear mass density of the first string.

Learn more about mass density

brainly.com/question/6107689

#SPJ11

A logical and probable explanation for the movement of the Earth’s tectonic plates is:
Group of answer choices
a. the breakup of the plates by volcanic eruptions and earthquakes
b. the rapid shrinking of Earth's crust as it slowly cools
c. the result of heat convection in the plastic mantle rock which moves the cold brittle crust on top
d. the rotation of the Earth causes the plates to drag across the top of the mantle

Answers

The logical and probable explanation for the movement of the Earth's tectonic plates is the convection currents within the mantle. The Earth's mantle is made up of hot, molten rock that constantly moves due to the heat generated by the radioactive decay of elements within the Earth's core.

This movement of the mantle creates convection currents that carry the tectonic plates along with them.
As the hot, less dense rock rises within the mantle, it pushes against the bottom of the tectonic plates, causing them to move away from each other. At the same time, cooler, denser rock sinks back down into the mantle, causing the tectonic plates to move towards each other.
This movement of the tectonic plates can cause a variety of geological phenomena such as earthquakes, volcanic eruptions, and the formation of mountains and ocean trenches. It is a slow but continuous process that has been ongoing for millions of years and will continue to shape the Earth's surface in the future.
In summary, the convection currents within the Earth's mantle are the most likely explanation for the movement of the tectonic plates. While other factors such as the rotation of the Earth may play a minor role, the convection currents are the driving force behind the movement of the tectonic plates.

For more such question on Earth

https://brainly.com/question/30033269

#SPJ11

The most accepted and widely supported explanation for the movement of the Earth's tectonic plates is option c: the result of heat convection in the plastic mantle rock which moves the cold brittle crust on top.

The Earth's mantle is composed of solid rock that can flow over long periods of time, and it is heated from below by the Earth's core. As the mantle heats up, it becomes less dense and rises towards the surface. This creates convection currents that move the molten rock in a circular motion, carrying the tectonic plates with them.

The movement of the tectonic plates is also influenced by the forces of gravity, as denser rock sinks and lighter rock rises. This process is known as "ridge push" and "slab pull," respectively. Ridge push occurs at mid-ocean ridges, where new crust is formed as magma rises to the surface, pushing the plates apart. Slab pull occurs at subduction zones, where old oceanic crust is pushed back into the mantle, dragging the rest of the plate along with it.

Option A (the breakup of the plates by volcanic eruptions and earthquakes) and option d (the rotation of the Earth causes the plates to drag across the top of the mantle) are not considered to be the primary drivers of plate tectonics, although they can contribute to it in certain circumstances. Option b (the rapid shrinking of Earth's crust as it slowly cools) is not a valid explanation for plate tectonics, as the Earth's crust is not shrinking rapidly enough to cause the observed movements of the plates.

Learn more about tectonic plates, here:

brainly.com/question/1162125

#SPJ11

A low-pass filter consists of a 116 μf capacitor in series with a 159 resistor. the circuit is driven by an ac source with a peak voltage of 4.40 v
What is VC when f=12fc?
What is VC when f=fc?
What is VC when f=2fc?

Answers

VC = 0.707Vpeak when f = 12fc, VC = 0.5Vpeak when f = fc, and VC = 0.293Vpeak when f = 2fc.

The impedance of a capacitor (ZC) in an AC circuit is given by ZC = 1/(jwC), where j is the imaginary unit, w is the angular frequency, and C is the capacitance. The impedance of a resistor (ZR) is given by ZR = R. The total impedance of a series RC circuit is Z = ZR + ZC = R + 1/(jwC). The voltage across the capacitor (VC) is given by VC = Vpeak × ZC/(ZC + ZR) = Vpeak/(1 + jwRC), where Vpeak is the peak voltage of the AC source.

When f = 12fc, w = 24pi, and

VC = Vpeak/√(1 + (24pi159116e-6)²) = 0.707Vpeak.

When f = fc, w = 2pi, and

VC = Vpeak/√(1 + (2pi159116e-6)²) = 0.5Vpeak.

When f = 2fc, w = 4pi, and

VC = Vpeak/√(1 + (4pi159116e-6)²) = 0.293Vpeak.

To learn more about capacitor, here

https://brainly.com/question/17176550

#SPJ4

The circuit you are describing is a simple RC series circuit, which acts as a low-pass filter. The voltage across the capacitor, VC, is given by the following equation:

VC = Vpeak / √(1 + (2πfRC)^2)

where V peak is the peak voltage of the AC source, f is the frequency of the AC source, R is the resistance of the resistor, and C is the capacitance of the capacitor.

For this circuit, we have C = 116 μF and R = 159 Ω.

Part A: When f = 12fc

Here, fc is the cutoff frequency of the filter, which is given by:

fc = 1 / (2πRC)

Substituting the given values, we get:

fc = 1 / (2π x 159 Ω x 116 μF) ≈ 91 Hz

Therefore, 12fc = 1,092 Hz.

Substituting these values into the equation for VC, we get:

VC = 4.40 V / √(1 + (2π x 1,092 Hz x 159 Ω x 116 μF)^2) ≈ 0.163 V

Thus, when the frequency is 12 times the cutoff frequency, VC is approximately 0.163 V.

Part B: When f = fc

Substituting fc = 91 Hz into the equation for VC, we get:

VC = 4.40 V / √(1 + (2π x 91 Hz x 159 Ω x 116 μF)^2) ≈ 0.689 V

Thus, when the frequency is equal to the cutoff frequency, VC is approximately 0.689 V.

Part C: When f = 2fc

Substituting 2fc = 182 Hz into the equation for VC, we get:

VC = 4.40 V / √(1 + (2π x 182 Hz x 159 Ω x 116 μF)^2) ≈ 1.15 V

Thus, when the frequency is twice the cutoff frequency, VC is approximately 1.15 V.

Learn more about  simple RC series circuit here : brainly.com/question/21092195

#SPJ11

1. Carefully find the threshold wavelength for sodium. What is the wavelength of the lowest energy light at which electrons are emitted?
Threshold wavelength =

Answers

Threshold wavelength for sodium is approximately 330 nm.

The threshold wavelength for sodium can be calculated using the following formula:

λth = hc/Φ

where λth is the threshold wavelength, h is Planck's constant, c is the speed of light, and Φ is the work function of sodium.

The work function of sodium is approximately 2.28 eV.

Converting electron volts (eV) to joules (J), we get:

Φ = 2.28 eV * 1.602 x 10⁻¹⁹ J/eV

Φ = 3.659 x 10⁻¹⁹ J

Plugging in the values of h, c, and Φ, we get:

λth = hc/Φ

λth = (6.626 x 10⁻³⁴ J s)(3.00 x 10⁸ m/s)/(3.659 x 10⁻¹⁹ J)

λth = 5.117 x 10⁻⁷ m

λth = 511.7 nm

Therefore, the threshold wavelength for sodium is approximately 511.7 nm.

The wavelength of the lowest energy light at which electrons are emitted can be found using the equation:

λ = hc/E

where λ is the wavelength, h is Planck's constant, c is the speed of light, and E is the energy of the light.

The lowest energy light corresponds to the work function of sodium, which is 2.28 eV.

Converting the energy to joules, we get:

E = 2.28 eV * 1.602 x 10⁻¹⁹ J/eV

E = 3.659 x 10⁻¹⁹ J

Plugging in the values of h, c, and E, we get:

λ = hc/E

λ = (6.626 x 10⁻³⁴ J s)(3.00 x 10⁸ m/s)/(3.659 x 10⁻¹⁹ J)

λ = 5.117 x 10⁻⁷ m

λ = 511.7 nm

Therefore, the wavelength of the lowest energy light at which electrons are emitted is approximately 511.7 nm, which is the same as the threshold wavelength for sodium.

To learn more about Threshold wavelength, here

https://brainly.com/question/21765974

#SPJ4

A −6.10−6.10-DD lens is held 10.5cm10.5cm from an ant 1.00mm1.00mm high
Find the image distance. Follow the sign conventions.
What is the height of the image? Follow the sign conventions.

Answers

The image distance is 15.3 cm. The height of the image is -0.15 mm.

Using the lens formula, 1/f = 1/v - 1/u, where f is the focal length, v is the image distance, and u is the object distance, we can solve for v. Since the lens is concave (negative focal length), f = -6.10 cm. The object distance, u, is 10.5 cm. Plugging in these values, we get 1/-6.10 = 1/v - 1/10.5. Solving for v gives v = 15.3 cm, indicating the image is formed on the same side as the object, which means it is a virtual image.

To find the height of the image, we can use the magnification formula, M = -v/u, where M is the magnification. Plugging in the values, we get M = -15.3/10.5 = -1.46. The negative sign indicates an inverted image. The height of the object is 1.00 mm. Multiplying the object height by the magnification gives the image height: -1.46 * 1.00 mm = -1.46 mm, or -0.15 mm to two significant figures.

Learn more about image distance here:

https://brainly.com/question/31319522

#SPJ11

electromagnetic write up of the brave little toaster movie

Answers

"The Brave Little Toaster" is an animated movie featuring five household appliances on a journey to find their owner, highlighting the power and importance of electromagnetics as they use electricity and electromagnetic fields to function and communicate with each other.

Electromagnetics is the study of the behavior and interaction of electric and magnetic fields. It includes the study of electromagnetic waves, which are waves of energy that are created by the oscillation of electric and magnetic fields. Electromagnetic waves can travel through empty space and are responsible for many phenomena, such as light, radio waves, microwaves, X-rays, and gamma rays. Electromagnetics is an important field of study in physics and engineering, with applications in many areas, including telecommunications, electronics, medical imaging, and energy production.

"The Brave Little Toaster" is an animated movie that features five household appliances on a journey to find their owner. The appliances include a toaster, a vacuum cleaner, a lamp, a radio, and an electric blanket. Throughout their adventure, they face various challenges and dangers, including a terrifying junkyard and a crushing machine. The movie highlights the power and importance of electromagnetics, as the appliances use electricity and electromagnetic fields to function and communicate with each other.

Therefore, Five household gadgets travel to locate their owner in the animated film "The Brave Little Toaster," which emphasises the relevance and power of electromagnetics because the equipment depend on electricity and electromagnetic fields to function.

To learn more about Brave Little Toaster click:

https://brainly.com/question/28888953

#SPJ1

Select the correct answer. Which of the following is not a result or consequence of rising average air temperatures on Earth? A. Glaciers and ice sheets melt. B. Sea levels rise. C. Evaporation increases. D. Salinity increases.

Answers

The correct option which is not a result or consequence of rising average air temperatures on Earth is (D) Salinity increases.

Salinity does not increase as a result of increasing air temperature. Salinity is the amount of salt in water. The amount of salt in water can increase due to evaporation and water loss, which leaves salt behind, or the addition of salt from land sources such as runoff. The consequence of rising average air temperature on Earth includes; Glaciers and ice sheets melt which causes sea levels to rise: With increased temperatures, ice on land is melting and flowing into the oceans, raising sea levels. This can lead to coastal flooding, beach erosion, and the displacement of communities living near coastlines. Evaporation increases which leads to changes in precipitation patterns: The increase in temperature leads to an increase in evaporation. The amount of water vapor in the air increases, which can lead to more intense precipitation in some areas and droughts in others. In summary, as the average air temperature continues to rise, the Earth's climate will continue to change, leading to various consequences such as melting of glaciers and ice sheets, increase in sea level, and changes in precipitation patterns. Salinity, however, is not affected by rising average air temperatures on Earth.

learn more about Salinity Refer: https://brainly.com/question/1807933

#SPJ11

use the relationship between resistance, resistivity, length, and cross-sectional area to estimate the resistance of a membrane segment Rmem using the following order-of-magnitude values.the diameter of the axon ~10 µm the membrane thickness ~10 nmthe resistivity of the axoplasm ~1 Ω .mthe average resistivity ol the membrane 10^ Ω.m the segment length ~1 mm

Answers

The estimated resistance of the membrane segment is approximately 1.27 x 10^11 Ω.

To estimate the resistance of a membrane segment (Rmem), we can use the formula:

R = (ρ * L) / A

Where R is resistance, ρ is resistivity, L is length, and A is the cross-sectional area. In this case, we have the following values:

- Diameter of the axon (d) = 10 µm
- Membrane thickness (t) = 10 nm
- Resistivity of the axoplasm (ρaxo) = 1 Ω.m
- Average resistivity of the membrane (ρmem) = 10^7 Ω.m
- Segment length (L) = 1 mm

First, we need to calculate the cross-sectional area of the membrane segment (A):

A = π * (d/2)^2

A = π * (10 µm / 2)^2
A ≈ 78.5 µm^2

Now, we can estimate the resistance of the membrane segment (Rmem):

Rmem = (ρmem * L) / A

Rmem = (10^7 Ω.m * 1 mm) / 78.5 µm^2
Rmem ≈ 1.27 x 10^11 Ω

So, the estimated resistance of the membrane segment is approximately 1.27 x 10^11 Ω.

To learn more about area, refer below:

https://brainly.com/question/27683633

#SPJ11

A thin film of polystyrene of refractive index 1.49 is used as a nonreflecting coating for Fabulite (strontium titanate) of refractive index 2.409.What is the minimum thickness of the film required? Assume that the wavelength of the light in air is 550nm .

Answers

The  minimum thickness of the polystyrene film required to act as a non-reflective coating for Fabulite is approximately 71.9 nanometers.

To determine the minimum thickness of the polystyrene film required to act as a non-reflective coating for Fabulite, we need to use the formula for the optical path difference:

OPD = 2t*(n2 - n1)/λ

where OPD is the optical path difference, t is the thickness of the film, n1 is the refractive index of the medium on one side of the film (in this case, air), n2 is the refractive index of the medium on the other side of the film (in this case, Fabulite), and λ is the wavelength of light in air.

If the film is acting as a non-reflective coating, then the optical path difference must be equal to λ/4. This ensures that the reflected light waves from the top and bottom surfaces of the film are 180 degrees out of phase, leading to destructive interference and minimal reflection.

Thus, we can rearrange the formula to solve for the minimum thickness of the film as:

t = λ/4*(n2 - n1)/n2

Plugging in the given values, we get:

t = (550 nm)/4 * (2.409 - 1.49)/2.409
 = 71.9 nm

Therefore, the minimum thickness of the polystyrene film required to act as a non-reflective coating for Fabulite is approximately 71.9 nanometers.

Visit to know more about Non-reflective:-

brainly.com/question/29742732

#SPJ11

 A spherical bulb 10 cm in radius is maintained at room temperature (300 K) except for one square centimeter which is kept at liquid nitrogen temperature (77 K). The bulb contains water vapor originally at a pressure of 0.1 mmHg. Assuming that every water molecule striking the cold area condenses and sticks to the surface, estimate the time required for the pressure to decrease to 10^-4 mmHg. [Assume that the gas remains in equilibrium at 300 K, but keeps losing molecules because of the " effusion" of molecules that hit the 1 cm^2 cold patch.]

Answers

The time required for the pressure to decrease to 10⁻⁴ mmHg is approximately 0.7 x 10⁵ s.

The rate at which water vapor molecules hit the cold patch and condense can be calculated using the kinetic theory of gases.

The number of water vapor molecules per unit volume in the bulb can be approximated by the ideal gas law:

PV = nRT

where,

P = pressure,

V = volume,

n = number of molecules,

R = gas constant, and

T = temperature.

Solving for n/V, we get:

n/V = P/RT

Given, P = 0.1 mmHg = 0.1/760 atm

           T = 300 K

Therefore, number of water vapor molecules per unit volume is:

n/V = (0.1/760 atm) / [(8.31 J/mol K) (300 K)]

      = 5.28 × 10⁻⁸ mol/m³

      = 5.28 × 10⁻⁸ * (6.02 x 10²³ molecules/mol)

      = 3.18 ×10¹⁶ molecules/m³

The rate at which water vapor molecules effuse through the cold patch can be approximated using Graham's law of effusion:

[tex]\frac{r_{1}}{r_{2}} =\sqrt{\frac{M_{2} }{M_{1} } }[/tex]

where rate1 and rate2 are the rates at which two gases effuse through a small hole, and M1 and M2 are their molecular masses.

In given condition,

we can treat the water vapor molecules as effusing through the cold patch into a vacuum,

∴ rate = A* (1/4) * (n/V) * √(8kT/πm)

where, A is the area of the cold patch, k is the Boltzmann constant, T is the temperature, and m is the mass of a water molecule.

Substituting the values, we get:

rate = 1 × 10⁻⁴ * (1/4) * (3.18×10¹⁶) * √[(8 * 1.38x10⁻²³ * 300) / (π * 3.01x10⁻²⁶)]

      = 1 × 10⁻⁴ * (1/4) * (3.18×10¹⁶) * 0.59

      = 4.69 x 10¹³ molecules/s

This is the rate at which water vapor molecules are removed from the bulb. The time required for the pressure to decrease to 10^-4 mmHg can be approximated by assuming that the pressure decreases exponentially with time:

P(t) = P₀ exp(-kt)

where P₀ is the initial pressure, k is a constant, and t is the time.

The constant k can be calculated from the rate:

k = rate / N

where N is the number of water molecules per unit volume.

Substituting the values, we get:

k = 4.69 x 10¹³ molecules/s / 3.18 ×10¹⁶ molecules/m³

k = 1.47x 10⁻³ s⁻¹

The time required for the pressure to decrease to 10⁻⁴ mmHg can then be calculated:

10⁻⁴ mmHg = 0.1 mmHg  exp(-1.47x 10⁻³ * t)

∴ t = 0.7 x 10⁵ s

Therefore, the time required for the pressure to decrease to 10⁻⁴ mmHg is approximately 0.7 x 10⁵ s.

Learn more about pressure here

brainly.com/question/26822196

#SPJ4

find (a) the amplitude and (b) the phase constant in the sum y of the following quantities: y1 = 11 sin ωt y2 = 16 sin(ωt 33°) y3 = 5.0 sin(ωt - 35°) using the phasor method.

Answers

(a) The amplitude of y is 18.6 units. (b) The phase constant of y is -14.9 degrees.

To use the phasor method, we convert each sinusoidal function into a phasor, which is a complex number representing the amplitude and phase of the function. The phasors can then be added algebraically to obtain the phasor for the sum. Finally, we convert the phasor for the sum back into a sinusoidal function.

For y1 = 11 sin ωt, the phasor is 11∠0°.For y2 = 16 sin(ωt - 33°), the phasor is 16∠(-33°).For y3 = 5.0 sin(ωt - 35°), the phasor is 5.0∠(-35°).

Adding these phasors gives us a phasor for y of:

y = 11∠0° + 16∠(-33°) + 5.0∠(-35°)= 18.6∠(-14.9°)

Therefore, the amplitude of y is 18.6 units, and the phase constant (or phase angle) is -14.9 degrees. We can write the sinusoidal function for y as:

y = 18.6 sin(ωt - 14.9°)

To learn more about phasor method, here

https://brainly.com/question/14673794

#SPJ4

convert the average p-wave speed you found in part b (480 km/min) from km/min to km/sec.

Answers

The average P-wave speed in km/sec is 8 km/sec.

To convert the average P-wave speed from km/min to km/sec, you'll need to divide the speed by the number of seconds in a minute.

This conversion allows us to express the speed in a different unit of time, from minutes to seconds. It is important to consider the appropriate units when performing conversions to ensure accurate and meaningful results.

In this case, the average P-wave speed of 8 km/sec provides a measure of how far the P-wave travels in one second. It represents the velocity at which the P-wave propagates through a medium, such as the Earth's crust during an earthquake.

There are 60 seconds in a minute, so:

Average P-wave speed in km/min = 480 km/min
Conversion factor = 1 min / 60 sec

To convert to km/sec, simply divide the speed by the conversion factor:

480 km/min × (1 min / 60 sec) = 480/60 km/sec = 8 km/sec

So, the average P-wave speed in km/sec is 8 km/sec.

To learn more about velocity, refer below:

https://brainly.com/question/17127206

#SPJ11

a hollow sphere is rolling along a horizontal floor at 7.00 m/s when it comes to a 27.0 ∘ incline

Answers

The height that the sphere reaches up the incline is: 1.09 m.

To solve this problem, we can use conservation of energy. The total energy of the system (kinetic plus potential) is conserved.

Initially, the sphere is rolling along a horizontal floor with a speed of 7.00 m/s. At this point, its kinetic energy is given by:
K1 = (1/2)mv^2
where m is the mass of the sphere and
v is its velocity.

As the sphere rolls up the incline, its potential energy increases due to the increase in height. The potential energy is given by:
U = mgh
where h is the height of the sphere above its initial position,
g is the acceleration due to gravity, and
m is the mass of the sphere.

At the top of the incline, the sphere is momentarily at rest, so all of its initial kinetic energy has been converted to potential energy:
K1 = U

Substituting the expressions for K1 and U, we have:
(1/2)mv^2 = mgh

Solving for h, we get:
h = (v^2)/(2g)

Plugging in the given values, we have:
h = (7.00 m/s)^2/(2*9.81 m/s^2)*sin(27.0°) = 1.09 m

To know more about "Kinetic energy" refer here:

https://brainly.com/question/30764377#

#SPJ11

find the area of the region in the first quadrant bounded by the line y​x, the line x​, the curve y ​, and the​ x-axis.

Answers

To find the area of the region in the first quadrant bounded by the given lines and curve, we need to evaluate a definite integral.

To find the area of the region in the first quadrant bounded by the line y=x, the line x=1, the curve y=1/x, and the x-axis, we can use the definite integral. First, we need to find the intersection point(s) of the curves. Setting y=x and y=1/x equal to each other, we get x=1. Therefore, the region of interest is between x=0 and x=1.

Next, we need to determine which curve is on top in this region. The curve y=1/x is on top since it is decreasing as x increases.

The definite integral for the area is then ∫[0,1] (1/x - x) dx. Integrating, we get the area is ln(1) - (1/2), or -1/2 ln(1) - 1/2.

Therefore, the area of the region in the first quadrant bounded by the line y=x, the line x=1, the curve y=1/x, and the x-axis is approximately 0.3069 square units.

Learn more about first quadrant bounded here:

https://brainly.com/question/31405813

#SPJ11

If it is impossible to raise the landing gear of a jet airplane, to obtain best range, the airspeed must be _____ from that for the clean configuration
a) increased
b) decreased
c) not change

Answers

a) increased. When the landing gear is down, it creates additional drag on the aircraft, which reduces its efficiency and range.

To compensate for this, the airspeed must be increased from that of the clean configuration (with the landing gear up) in order to achieve the best possible range.


If it is impossible to raise the landing gear of a jet airplane, to obtain the best range, the airspeed must be a) increased from that for the clean configuration. This is because the landing gear increases drag, so a higher airspeed is needed to overcome the additional drag and maintain optimal range.

To know more about Airspeed visit:

https://brainly.com/question/29597908

#SPJ11

Other Questions
During early Drosophila development, the zygote undergoes many rounds of _____________.A) holoblastic cleavageB) implantationC) mitosis, but not cytokinesisD) meroblastic cleavage, with each cell asymmetrically smaller than the next Which of the following could result in weak motor movements in the hip? A. A tumor on the medial side of the primary somatosensory cortex B. A higher than normal amount of myosin and actin proteins found inside muscle fibers near the hip C. A higher than normal concentration of calcium stored in the sarcoplasmic reticulum inside muscle fibers near the hip D. A tumor on the medial side of the primary motor cortex What is the two's complement of 1000 00112 a. 0111 10102 b. 1001 01012 c. 0000 01112 Q20 Refer to the symbol shown as a Figure for the Full Adder. What are the output when A - 1, B=1,Cin=1? a. = 0, cout = 1 b, = 1, Cout = 0 c. :0, cout:0 d. -1, Cout 1 n out In the context of the passage, lines 26-30 ("I couldn't. Her) are primarily meant to A) recount an anecdote. B) describe a theory. C) present an example. D) note an impression. a carboxylic acid can condense with a sulfhydryl group to produce: Rewrite the biconditional statement to make it valid. ""A quadrilateral is a square if and only if it has four right angles. "" during the turmoil in the market for subprime mortgages in 2007 and 2008, the fed increased the volume of discount loans. the main goal of the fed at the time was to describe in words and give an equation for the kind of force that produces simple harmonic motion how large an area is required to supply the needs of a house that requires 23 kwh/day? assume there are 9 hours of sunlight per day. Calculate the pH of a solution made by mixing equal volumes of a solution of NaOH with a pH of 11.40 and a solution of KOH with a pH of 10.30 at 25C. (Assume the volumes are additive.) A. 1.10 B. 10.85 C. 11.13 D. 21.70 E. none of these Jennifer earns $17. 35 per hour at her job. She works 6 hours per day, 5 days per week. What is Jennifers gross income for a 2 week pay period? a. $520. 50 b. $694. 00 c. $867. 50 d. $1,041. 00 Please select the best answer from the choices provided A B C D. Within 30 minutes of consuming asparagus an estimated 40 to 50% of the North American population acquires pungent smelling pee. The smelly asparagus urine results from the breakdown of sulfur-rich compounds by digestive enzymes in the gut Once you estimate the frequency of the recessive 'non-smelly allele in the population, what equation do you use to estimate the frequency of the dominant allele? the united states most closely resembles which type of economic system? If a cone-shaped water cup holds 23 cubic inches and has a radius of 1 inch, what is the height of the cup? Use 3. 14 to for pi. Round your answer to the nearest hundredth. 6. 76 in 18. 56 in 21. 97 in 23. 00 in. When SFC cannot fix a problem with a corrupted Windows 10 installation, you can use DISM commands to repair system files. Read Chapter 14 and use perform an online search to help you form your answers.1. What is DISM?2. Where can a technician find DISM on a Windows 10 operating system? (List the exact steps)3. List 2 scenarios when using DISM over SFC would be appropriate.Your initial post should consist of a minimum of 100 words. The posts to your two classmates should be a minimum of 50 words each. What is the total pressure at 60m depth of water? (Round to closest 100kPa) calculate the average kinetic energy of co2 molecules with a root-mean-square speed of 629 m/s. report your answer in kj/mol. (1 j = 1 kg m2/s2; 1 mol = 6.02 1023) Historically demand has averaged 1102 units per week with a standard deviation of 770. The company currently has 2857 units in stock. What is the probability of a stockout? Z = (X u)/o A. 228 % B.98.87 %C. 50% D. 48.87%E. 1.130% Use the Ratio Test to determine the radius of convergence of [infinity]=0x7. (Use symbolic notation and fractions where needed.) Why were the powers of persuasion considered potentially dangerous in democratic Athens?