The planet that has an axis that points roughly straight up, and thus has no seasons to speak of, is

Answers

Answer 1

The planet that has an axis that points roughly straight up, and thus has no seasons to speak of, is Uranus.

The Earth's axis is tilted relative to its orbit around the Sun, which causes the changing seasons we experience throughout the year.

However, there are other planets in our solar system with different axial tilts, leading to different seasonal patterns.

Uranus is the planet known for having an extreme axial tilt. Its axis is tilted at an angle of about 98 degrees relative to its orbital plane.

Due to this extreme tilt, Uranus' axis points roughly straight up and down as it orbits the Sun.

Since the axis is nearly perpendicular to its orbit, Uranus experiences very little variation in sunlight throughout its year.

As a result, Uranus has minimal or no observable seasons compared to other planets in our solar system.

Therefore, the planet that has an axis that points roughly straight up and thus has no seasons to speak of is Uranus.

For more such questions on planet, click on:

https://brainly.com/question/28430876

#SPJ8


Related Questions

A simple pendulum on earth has a period of 6.0 s. What is the approximate period of this pendulum on the moon where the acceleration due to gravity is roughly 1/6 that of earth? a. 1.0s b. 2.4 s c. 36 s d. 15 s
e. 6.05s

Answers

The approximate period of this pendulum on the moon where the acceleration due to gravity is roughly 1/6 that of earth is 15s. The correct option is -d. 15 s.

On Earth, we know that T=6.0 s. Let's assume the length of the pendulum remains constant.
Now, on the moon, the acceleration due to gravity is approximately 1/6 that of Earth's, so g'=g/6.

Using the same equation as before, we can find the new period T' on the moon:
T' = 2π√(L/g') = 2π√(L/(g/6)) = 2π√(6L/g)

Substituting in T=6.0 s, we have:
T' = 2π√(6L/g) = 2π√(6T^2g/L) = 2π√(6(6.0 s)^2(9.81 m/s^2)/L)

Since we are looking for an approximate answer, we can estimate L to be roughly the same on the moon as it is on Earth. Therefore, we can simplify the equation to:

T' ≈ 2π√(6(6.0 s)^2(9.81 m/s^2)/L) ≈ 2π√(216) ≈ 29.1 s
Therefore, the correct option is -d. 15 s.

For more question on acceleration

https://brainly.com/question/460763

#SPJ11

The period of a pendulum is the time it takes for the pendulum to complete one full swing. In this case, we know that a simple pendulum on earth has a period of 6.0 s. However, on the moon, the acceleration due to gravity is roughly 1/6 that of earth.Therefore, the correct answer is (b) 2.4 s.

This means that the force acting on the pendulum is much weaker on the moon than on earth. As a result, the pendulum will swing slower on the moon than on earth. To calculate the approximate period of the pendulum on the moon, we can use the formula T=2π√(l/g), where T is the period, l is the length of the pendulum, and g is the acceleration due to gravity. Plugging in the appropriate values, we get T=2π√(l/(1/6g)). Simplifying this equation, we can see that the period on the moon will be approximately 2.4 s. Therefore, the correct answer is (b) 2.4 s.

To learn more about simple pendulum click here: brainly.com/question/29183311  
#SPJ11

An electron-positron pair is produced by a 2.50 MeV photon. What is the kinetic energy of the positron if the kinetic energy of the electron is 0.739
MeV?
Use the following Joules-to-electron-Volts conversion 1eV = 1.602 × 10-19 J.
The rest mass of an electron is 9.11 Å~10−31 kg

Answers

The total energy of the electron-positron pair produced by a 2.50 MeV photon is 2.50 MeV. Subtracting the electron's kinetic energy of 0.739 MeV gives the positron's kinetic energy of 1.76 MeV. Using the given conversion factor, this corresponds to 2.81 × [tex]10^-^1^3[/tex] J.

What is the kinetic energy of the positron produced by a 2.50 MeV photon?

The total energy of the electron-positron pair produced by a 2.50 MeV photon is given by:

[tex]E_p_a_i_r[/tex] = [tex]E_p_h_o_t_o_n[/tex] = 2.50 MeV

The kinetic energy of the electron is given as:

[tex]K_e_l_e_c_t_r_o_n[/tex] = 0.739 MeV

To find the kinetic energy of the positron, we subtract the kinetic energy of the electron from the total energy of the pair:

[tex]K_p_o_s_i_t_r_o_n[/tex] = [tex]E_p_a_i_r[/tex] - [tex]K_e_l_e_c_t_r_o_n[/tex] = 2.50 MeV - 0.739 MeV = 1.76 MeV

To convert this value to joules, we use the conversion factor:

1 eV = 1.602 × [tex]10^-^1^9[/tex] J

Therefore, the kinetic energy of the positron is:

[tex]K_p_o_s_i_t_r_o_n[/tex] = 1.76 MeV x 1.602 × [tex]10^-^1^9[/tex] J/eV = 2.81 × [tex]10^-^1^3[/tex] J

Learn more about Electron-positron pair

brainly.com/question/13143222

#SPJ11

a balloon has a volume of 4.0 liters at 24.0°c. the balloon is heated to 48.0°c. calculate the new volume of the balloon (in liters).

Answers

The new volume of the balloon at 48.0°C is approximately 4.83 liters.

To calculate the new volume of the balloon, we can use the ideal gas law: PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the gas constant, and T is the temperature in Kelvin.

Since the amount of gas and the pressure are constant in this problem, we can use the simplified version of the ideal gas law: V1/T1 = V2/T2, where V1 is the initial volume, T1 is the initial temperature, V2 is the final volume (what we're trying to find), and T2 is the final temperature.

Converting the temperatures to Kelvin by adding 273.15, we get: V1/T1 = V2/T2, 4.0 L / (24.0 + 273.15) K = V2 / (48.0 + 273.15) K. Solving for V2, we get: V2 = (4.0 L * (48.0 + 273.15) K) / (24.0 + 273.15) K, V2 ≈ 4.83 L

Therefore, the new volume of the balloon at 48.0°C is approximately 4.83 liters.

To know more about gas constant, refer here:

https://brainly.com/question/14279790#

#SPJ11

18) a thallium sample has an activity of 2 x 108 bq today, thallium has a half-life of 3.7 years, what was the activity of the sample 100 years ago (in the past)?

Answers

The activity of the sample 100 years ago (in the past) is approximately [tex]8.7 * 10^{6} bq[/tex] .

To solve this problem, we can use the formula for radioactive decay:

A = A₀ e^(-λt)

Where:
A₀ is the initial activity
A is the current activity
λ is the decay constant
t is the time elapsed

We can rearrange this formula to solve for the initial activity A₀:

A₀ = A / e^(-λt)

First, we need to find the decay constant λ, which is related to the half-life t½ by the formula:

t½ = ln(2) / λ

Rearranging this formula gives us:

λ = ln(2) / t½

Substituting the values given in the problem, we have:

t½ = 3.7 years
λ = ln(2) / 3.7 years ≈ 0.187 [tex]years^{-1}[/tex]

Next, we need to find the time elapsed t between the present day and 100 years ago. Since the half-life of thallium is 3.7 years, we can divide 100 years by 3.7 years to get:

t = 100 years / 3.7 years ≈ 27.0

Now we can substitute the values we have found into the formula for A₀:

A₀ = A / e^(-λt)
A₀ = [tex]2*10^{8}[/tex] bq / [tex]e^{(-0.187 years^{-1}*27.0 years) }[/tex]
A₀ ≈ [tex]8.7 * 10^{6} bq[/tex]

Therefore, the activity of the thallium sample 100 years ago (in the past) was approximately [tex]8.7 * 10^{6} bq[/tex].

Know more about   half-life   here:

https://brainly.com/question/1160651

#SPJ11

A box of unknown mass is sliding with an initial speed vi = 4.00 m/s across a horizontal frictionless warehouse floor when it encounters a rough section of flooring d = 2.50 m long. The coefficient of kinetic friction between the rough section of flooring and the box is 0.100. Using energy considerations, determine the final speed of the box after sliding across the rough section of flooring.

Answers

The final speed of the box after sliding across the rough section of flooring is approximately 3.33 m/s.

To determine the final speed of the box after sliding across the rough section of flooring, we can use energy conservation.

The initial kinetic energy of the box is given by:

KEi = 1/2 × mv²,

where m is the mass of the box and v is the initial speed.

The work done by friction can be calculated as the product of the force of friction and the distance over which it acts:

Work = Frictional force × Distance = μk × mg × d,

where μk is the coefficient of kinetic friction, m is the mass of the box, g is the acceleration due to gravity, and d is the distance.

According to the work-energy principle, the change in kinetic energy is equal to the work done by external forces:

ΔKE = Work.

The final kinetic energy of the box is given by:

KEf = 1/2 × mvf²,

where vf is the final speed.

Since there is no change in gravitational potential energy, we can write:

ΔKE = KEf - KEi = Work.

Substituting the expressions for ΔKE, KEf, and Work, we have:

1/2 × mvf² - 1/2 × mvi² = μk × mg × d.

Simplifying the equation and solving for vf, we get:

vf² = vi² - 2 × μk × g × d.

Plugging in the given values, we have:

vf² = (4.00 m/s)² - 2 × (0.100) × 9.8 m/s² × (2.50 m).

Calculating the right-hand side of the equation, we find:

vf² ≈ 16.00 m²/s² - 4.90 m²/s².

vf² ≈ 11.10 m²/s².

Taking the square root of both sides, we obtain:

vf ≈ √(11.10 m²/s²).

vf ≈ 3.33 m/s.

You can learn more about the speed at: brainly.com/question/17661499

#SPJ11

(20 points) the orbit of a satellite around an unspeci ed planet has an inclination of 30 , and its argument of periapsis advances at the rate of 5 per day. at what rate does the node line regress?

Answers

The rate at which the node line regresses is 5/2 degrees per day.

The regression of the node line is caused by the gravitational pull of the planet on the inclined orbit of the satellite. The rate of regression can be calculated using the formula:

n = -2/3 * n' * cos(i)

where n is the rate of regression, n' is the rate of advancement of the argument of periapsis, and i is the inclination of the orbit.

Substituting the given values, we get:

n = -2/3 * 5 * cos(30)

n = -2.5 * cos(30)

n = -2.5 * √3/2

n = -2.5 * 0.866

n = -2.165 degrees per day

However, for the rate in degrees per day, we need to take the absolute value of the answer, which is approximately 2.165 degrees per day. As a result, the node line regresses at a rate of 5/2 degrees every day.

To know more about the Satellite, here

https://brainly.com/question/13769231

#SPJ4

a certain laser emits light of wavelength 688 ✕ 10-9 m. what is the frequency of this light in a vacuum

Answers

The frequency of the light emitted by the laser in a vacuum is approximately 4.36 x 10^14 Hz.

The frequency of the laser's light in a vacuum can be found using the formula f=c/λ, where f is frequency, c is the speed of light in a vacuum, and λ is the wavelength of the light. So, to find the frequency of the laser's light, we can plug in the given values:

f = c/λ
f = (3.00 ✕ 10^8 m/s)/(688 ✕ 10^-9 m)
f = 4.36 ✕ 10^14 Hz

The speed of light in a vacuum is approximately 3.0 x 10^8 m/s. So, the frequency of the light emitted by the laser in a vacuum is approximately 4.36 x 10^14 Hz.

To know more about laser visit:-

https://brainly.com/question/27853311

#SPJ11

a sound wave has a frequency of 3000hz what is the edistance btweeeen crests of the wavbe

Answers

The distance between crests of the sound wave is 0.114 meters, or 11.4 centimeters.

The distance between crests of a sound wave, or any wave, is called the wavelength (represented by the symbol λ). The wavelength can be calculated using the formula λ = v/f, where v is the speed of the wave and f is its frequency.

The speed of sound waves depends on the medium through which they are traveling. In air at room temperature and atmospheric pressure, the speed of sound is approximately 343 meters per second (m/s). Therefore, the wavelength of a sound wave with a frequency of 3000 Hz can be calculated as follows:

λ = v/f = 343 m/s / 3000 Hz = 0.114 m

So, the distance between crests of the sound wave is 0.114 meters, or 11.4 centimeters.

It is worth noting that sound waves are longitudinal waves, which means that the oscillations are parallel to the direction of wave propagation. This is in contrast to transverse waves, such as electromagnetic waves, in which the oscillations are perpendicular to the direction of wave propagation. In a longitudinal wave, the distance between successive compressions or rarefactions is equal to one wavelength.

In summary, the wavelength of a sound wave with a frequency of 3000 Hz is 0.114 meters, or 11.4 centimeters, assuming that the wave is traveling through air at room temperature and atmospheric pressure.

To learn more about sound wave refer here:

https://brainly.com/question/21995826

#SPJ11

A skier with a mass of 70 kg starts from rest and skis down an icy (frictionless) slope that has a length of 52 m at an angle of 32 with respect to the horizontal. At the bottom of the slope, the path levels out and becomes horizontal, the snow becomes less icy, and the skier begins to slow down, coming to rest in a distance of 160 m along the horizontal path.(a) What is the speed of the skier at the bottom of the slope?(b) What is the coefficient of kinetic friction between the skier and the horizontal surface?

Answers

(a) The speed of the skier at the bottom of the slope is 16.3 m/s. b)  The coefficient of kinetic friction between the skier and the horizontal surface is 0.167. To find the speed of the skier at the bottom of the slope, we can use conservation of energy.

The initial potential energy of the skier at the top of the slope is converted into kinetic energy as the skier moves down the slope. When the skier reaches the bottom of the slope, all the potential energy is converted to kinetic energy.

Let's start by finding the height of the slope: h = Lsin(θ) = 52 sin(32°) = 28.2 m. The initial potential energy of the skier is mgh = 70 kg x 9.8 x 28.2 m = 19,656 J.

At the bottom of the slope, all of this potential energy is converted to kinetic energy, so: 1/2 [tex]mv^2[/tex]= 19,656 J Solving for v, we get: v = sqrt((2 x 19,656 J) / 70 kg) = 16.3 m/s

Therefore, the speed of the skier at the bottom of the slope is 16.3 m/s. To find the coefficient of kinetic friction between the skier and the horizontal surface, we need to use the distance the skier slides along the horizontal path to find the work done by friction, which is then used to find the force of friction.

The work done by friction is given by W = Ff d, where Ff is the force of friction and d is the distance the skier slides along the horizontal path. The work done by friction is equal to the change in kinetic energy of the skier, which is: W = 1/2 [tex]mvf^2 - 1/2 mvi^2[/tex]

where vf is the final velocity of the skier (zero) and vi is the initial velocity of the skier (16.3 m/s). W = -1/2 (70 kg) (16.3 m/s) = -18,254 JTherefore, the force of friction is: Ff = W / d = -18,254 J / 160 m = -114 N

The force of friction is in the opposite direction to the motion of the skier, so we take its magnitude to find the coefficient of kinetic friction:

Ff = uk mg

-114 N = uk (70 kg) (9.8)

uk = 0.167, Therefore, the coefficient of kinetic friction between the skier and the horizontal surface is 0.167.

Know more about kinetic friction here:

https://brainly.com/question/30886698

#SPJ11

two resistors are wired in series. in another circuit, the same two resistors are wired in parallel. in which circuit is the equivalent resistance greater?

Answers

Answer:

The circuit in series has a greater resistance.

Explanation:

The current is forced to flow throw two resistors instead of just one as it if it were in parallel.

fill in the blank. ___ a possible means of space flight is to place a perfectly reflecting aluminized sheet into orbit around the earth and then use the light from the sun to push this ""solar sail.""

Answers

A solar sail is a possible means of space flight that utilizes the momentum of sunlight to propel a spacecraft.

This innovative technique involves placing a perfectly reflecting aluminized sheet, known as the solar sail, into orbit around the Earth.

The light from the Sun, composed of photons, exerts pressure on the sail, causing it to move through space. As the photons reflect off the sail, they transfer their momentum to it, pushing it forward.

This method of propulsion is efficient and environmentally friendly, as it does not require any fuel or emit any pollutants.

Moreover, solar sails can continuously accelerate, reaching higher speeds over time, making them a promising technology for exploring the cosmos.

Learn more about solar sail at

https://brainly.com/question/29698445

#SPJ11

A three-phase bridge inverter used for a brushless motor outputs a square wave voltage has a 100Vdc power supply and is producing a square wave output at 60Hz. a) Determine the total rms output line-line voltage. b) Determine the rms value of the fundamental component of the line-line voltage.

Answers

a) The total rms output line-line voltage is approximately 70.71V.

b) The rms value of the fundamental component of the line-line voltage is approximately 50V.

a) The total root mean square (rms) output line-line voltage of the three-phase bridge inverter can be calculated by dividing the DC power supply voltage (100Vdc) by the square root of 2 (√2), resulting in approximately 70.71V. This represents the effective voltage level of the square wave output.

b) The rms value of the fundamental component of the line-line voltage in a square wave can be determined by dividing the total rms output voltage (70.71V) by √2, yielding approximately 50V. This value corresponds to the magnitude of the fundamental frequency component of the square wave, representing the primary voltage level of interest in the system.

Learn more about rmc output line-line voltage here:

https://brainly.com/question/31963305

#SPJ11

(a) Calculate the work (in MJ) necessary to bring a 101 kg object to a height of 992 km above the surface of the Earth.__ MJ (b) Calculate the extra work (in J) needed to launch the object into circular orbit at this height.__J

Answers

(a) The work necessary to bring a 101 kg object to a height of 992 km above the surface of the Earth is 986 MJ. (b) The extra work needed to launch the object into circular orbit at a height of 992 km above the surface of the Earth is 458 MJ.

To bring an object to a height of 992 km above the surface of the Earth, we need to do work against the force of gravity. The work done is given by the formula;

W = mgh

where W is work done, m is mass of the object, g is acceleration due to gravity, and h is the height above the surface of the Earth.

Using the given values, we have;

m = 101 kg

g = 9.81 m/s²

h = 992 km = 992,000 m

W = (101 kg)(9.81 m/s²)(992,000 m) = 9.86 × 10¹¹ J

Converting J to MJ, we get;

W = 986 MJ

Therefore, the work necessary to bring a 101 kg object to a height of 992 km above the surface of the Earth is 986 MJ.

To launch the object into circular orbit at this height, we need to do additional work to overcome the gravitational potential energy and give it the necessary kinetic energy to maintain circular orbit. The extra work done is given by the formula;

W = (1/2)mv² - GMm/r

where W is work done, m is mass of the object, v is velocity of the object in circular orbit, G is gravitational constant, M is the mass of the Earth, and r is the distance between the object and the center of the Earth.

We can find the velocity of the object using the formula:

v = √(GM/r)

where √ is the square root symbol. Substituting the given values, we have;

v = √[(6.67 × 10⁻¹¹ N·m²/kg²)(5.97 × 10²⁴ kg)/(6,371 km + 992 km)] = 7,657 m/s

Substituting the values into the formula for work, we have;

W = (1/2)(101 kg)(7,657 m/s)² - (6.67 × 10⁻¹¹ N·m²/kg²)(5.97 × 10²⁴ kg)(101 kg)/(6,371 km + 992 km)

W = 4.58 × 10¹¹ J

Converting J to the required units, we get;

W = 458 MJ

Therefore, the extra work needed to launch the object into circular orbit at a height of 992 km above the surface of the Earth is 458 MJ.

To know more about circular orbit here

https://brainly.com/question/19131814

#SPJ4

--The given question is incomplete, the complete question is

"(a) Calculate the work (in MJ) necessary to bring a 101 kg object to a height of 992 km above the surface of the Earth.__ MJ (b) Calculate the extra work (in MJ) needed to launch the object into circular orbit at this height of 992 km above the surface of the Earth .__MJ."--

a tank contains 23 kg of dry air and 0.3 kg of water vapor at 35 0c and 88 kpa total pressure.

Answers

The tank contains 23 kg of dry air and 0.3 kg of water vapor at 35°C and 88 kPa, with a partial pressure of dry air of 86.3 kPa and a volume of 23.9 m³.

How to calculate air composition?

we can calculate the volume of the tank and the partial pressure of the dry air by using the ideal gas law:

First, we need to calculate the mole fraction of water vapor in the tank:

n_total = (23 kg + 0.3 kg) / (28.97 kg/kmol) = 0.802 kmoln_water_vapor = 0.3 kg / (18.015 kg/kmol) = 0.0167 kmolx_water_vapor = n_water_vapor / n_total = 0.0208

Next, we can calculate the partial pressure of the dry air:

P_total = 88 kPa

P_dry_air = (1 - x_water_vapor) * P_total = 86.3 kPa

Using the ideal gas law, we can calculate the volume of the tank:

V = (n_total * R * T) / P_total

where R is the universal gas constant (8.314 J/(mol*K)), and T is the temperature in Kelvin:

T = 35°C + 273.15 = 308.15 K

V = (0.802 kmol * 8.314 J/(mol*K) * 308.15 K) / 88 kPa = 23.9³

Therefore, the tank contains 23 kg of dry air and 0.3 kg of water vapor at a total pressure of 88 kPa and a temperature of 35°C, with a partial pressure of dry air of 86.3 kPa, and a volume of 23.9 m³.

Learn more about pressure

brainly.com/question/12971272

#SPJ11

a diffraction grating with 335 lines/mmlines/mm is 1.55 mm in front of a screen. What is the wavelength of light whose first-order maxima will be 16.4 cm from the central maximum on the screen?
What is the answer to this question and how do you come up with it?

Answers

The wavelength of light whose first-order maxima will be 16.4 cm from the central maximum on the screen is approximately 0.0355 μm.

we can use the equation:

d * sin(theta) = m * lambda

where d is the distance between adjacent lines on the diffraction grating, theta is the angle between the incident light and the diffracted light, m is the order of the maximum, and lambda is the wavelength of the light.

First, we need to calculate the value of d, which is given as 335 lines/mm. To convert this to meters, we divide by 1000:

d = 335 lines/mm / 1000 mm/m = 0.335 lines/m

Next, we need to calculate the angle theta. The distance between the central maximum and the first-order maximum is given as 16.4 cm, which is 0.164 m. Since the diffraction grating is 1.55 mm away from the screen, we can assume that the angle theta is small, and we can use the approximation:

sin(theta) ≈ tan(theta) ≈ opposite/adjacent = 0.164 m / 1.55 mm = 0.000106

Now we can plug in the values we have into the equation and solve for lambda:

d * sin(theta) = m * lambda

0.335 lines/m * 0.000106 ≈ lambda

lambda ≈ 0.0355 μm

Therefore, the wavelength of light whose first-order maxima will be 16.4 cm from the central maximum on the screen is approximately 0.0355 μm.

For more such questions on wavelength , Visit:

https://brainly.com/question/10728818

#SPJ11

The wavelength of light whose first-order maxima will be 16.4 cm from the central maximum on the screen is 3150 nm.

To solve this problem, we can use the formula:

d*sinθ = m*λ

where d is the distance between adjacent slits on the diffraction grating (in this case, 1/335 mm), θ is the angle between the incident light and the diffracted light, m is the order of the maximum (in this case, 1), and λ is the wavelength of the light.

We want to find λ when the first-order maximum is 16.4 cm from the central maximum on the screen. We can use the small angle approximation sinθ ≈ θ, and we know that the distance between the diffraction grating and the screen is 1.55 mm. Therefore, we have:

d*θ = m*λ
θ = (16.4 cm - 0 cm)/1.55 mm
θ = 1.056 radians (approximately)

Substituting the values we have:

(1/335 mm)*1.056 = 1*λ
λ = (1/335 mm)*1.056
λ = 3.15 x 10^-6 meters (or 3150 nanometers)

Learn  more about diffraction brainly.com/question/12290582?

#SPJ11

(a) An 8-bit A/D converter has an input range of 0 to 15 V and an output in simple binary. Find the output (in decimal) if the input is (a) 6.42 V (6) -6.42 V (C) 12 V (d) OV (b) Convert Hexa decimal Number B602 to a decimal number and Binary. Convert decimal number 227 to binary number.

Answers

The sequence of remainders in reverse order is 11100011. Therefore, the binary representation of 227 is 11100011.

(a) To find the output of an 8-bit A/D converter, we need to determine the resolution of the converter. The resolution is the smallest change in the input voltage that can be detected by the converter. For an 8-bit converter, the resolution is calculated as follows:

Resolution = Input Range / ([tex]2^8[/tex] - 1) = 15 V / 255 = 0.0588 V

Using this resolution, we can calculate the output in decimal for each input voltage as follows:

(a) Input voltage = 6.42 V

Output in decimal = 6.42 / 0.0588 = 109

(c) Input voltage = -6.42 V

Output in decimal = (-6.42 + 15) / 0.0588 = 170

(d) Input voltage = 12 V

Output in decimal = 12 / 0.0588 = 204

(b) To convert the hexadecimal number B602 to decimal, we need to multiply each digit by its corresponding power of 16 and add the results. The calculation is as follows:

[tex]$B602 = (11 \times 16^3) + (6 \times 16^2) + (0 \times 16^1) + (2 \times 16^0) = 46,082$[/tex]

To convert the decimal number 227 to binary, we can use the division-by-2 method. We divide the decimal number by 2 and record the remainder (either 0 or 1). We continue the process with the quotient until we reach 0. The binary number is the sequence of remainders in reverse order. The calculation is as follows:

227 / 2 = 113 remainder 1

113 / 2 = 56 remainder 1

56 / 2 = 28 remainder 0

28 / 2 = 14 remainder 0

14 / 2 = 7 remainder 0

7 / 2 = 3 remainder 1

3 / 2 = 1 remainder 1

1 / 2 = 0 remainder 1

To learn more about binary

https://brainly.com/question/31413821

#SPJ4

(a) The output in decimal for an 8-bit A/D converter with an input range of 0 to 15 V is as follows:

(a) For an input of 6.42 V, the output in decimal would be 104.

(b) For an input of -6.42 V, the output in decimal would be 0.

(c) For an input of 12 V, the output in decimal would be 195.

(d) For an input of 0 V, the output in decimal would be 0.

Determine the output in decimal?

In an 8-bit A/D converter, the input range of 0 to 15 V is divided into 256 equal steps. Each step corresponds to a certain decimal value. To find the output in decimal, we need to determine which step the input voltage falls into and assign the corresponding decimal value.

(a) For an input of 6.42 V, we calculate the fraction of the input voltage in relation to the total range: (6.42 V / 15 V) ≈ 0.428. Multiplying this fraction by the total number of steps (256), we find that the input falls into approximately step 109. Therefore, the output in decimal is 109.

(b) For an input of -6.42 V, since the input voltage is negative and below the defined range, the output is 0.

(c) For an input of 12 V, the fraction of the input voltage is (12 V / 15 V) = 0.8. Multiplying this fraction by 256, we find that the input falls into step 204. Therefore, the output in decimal is 204.

(d) For an input of 0 V, as it is the lower limit of the input range, the output is 0.

(b) Converting the hexadecimal number B602 to a decimal number yields 46626. To convert it to binary, we can break down each hexadecimal digit into its binary representation: B = 1011, 6 = 0110, 0 = 0000, and 2 = 0010.

Combining these binary representations, the binary equivalent of B602 is 1011001100000010.

(c) Converting the decimal number 227 to a binary number, we can use the method of successive division by 2.

Dividing 227 by 2 repeatedly, we get the remainders: 1, 1, 0, 0, 0, 1, and 1. Reading these remainders in reverse order, the binary equivalent of 227 is 11100011.

To know more about decimal, refer here:

https://brainly.com/question/30958821#

#SPJ4

the instant the switch is closed what is the voltage across the resistor, in volts? rl switch circuit select one: a. 0 b. 20 c. 40 d. 2

Answers

The instant the switch is closed what is the voltage across the resistor, in volts. The correct answer is: a. 0

The voltage across the resistor in an RL switch circuit the instant the switch is closed can be determined using Ohm's Law and considering the initial conditions of the circuit. Here are the provided options:

a. 0
b. 20
c. 40
d. 2

At the instant the switch is closed, the inductor in an RL circuit initially behaves like an open circuit. This is because it takes some time for the current to build up in the inductor, and it opposes any sudden change in current. As a result, the initial current through the circuit is 0A.

Using Ohm's Law (V = IR), where V is the voltage across the resistor, I is the current through the resistor, and R is the resistance, we can calculate the initial voltage across the resistor. Since the current I is 0A at this instant, the voltage across the resistor is:

V = 0A * R = 0V

Learn more about voltage here:-

https://brainly.com/question/13396105

#SPJ11

The sun emits energy in the form of electromagnetic waves at a rate of 3.9 x 1026 W. This energy is produced by nuclear reactions deep in the sun's interior. Part A Find the intensity of electromagnetic radiation at the surface of the sun (radius r = R=6.96 x 105 km).

Answers

The intensity of electromagnetic radiation at the surface of the sun is approximately 6.33 x 10^7 W/m^2. This intense radiation is a result of the nuclear reactions happening deep within the sun's core, which produce huge amounts of energy in the form of electromagnetic waves.

The intensity of electromagnetic radiation at the surface of the sun can be calculated using the formula I = P/4πr^2, where I is the intensity, P is the power emitted, and r is the distance from the source. In this case, the power emitted by the sun is 3.9 x 10^26 W and the distance from the center of the sun to its surface (radius) is R = 6.96 x 10^5 km.

Converting the radius to meters, we get r = 6.96 x 10^8 m. Plugging in the values, we get:

I = (3.9 x 10^26 W) / (4π x (6.96 x 10^8 m)^2)
I = 6.33 x 10^7 W/m^2

Therefore, the intensity of electromagnetic radiation at the surface of the sun is approximately 6.33 x 10^7 W/m^2. This intense radiation is a result of the nuclear reactions happening deep within the sun's core, which produce huge amounts of energy in the form of electromagnetic waves.

To know more about   electromagnetic radiation visit:

brainly.com/question/10759891

#SPJ11

Two identical spaceships are moving through space both with speed v0. both spaceships experience a net force of magnitude f0 over the same time interval. for spaceship 1, the net force acts in the same direction as the spaceship is moving; for spaceship 2, the net force is directed opposite to the spaceship’s motion, causing spaceship 2 to slow down but not stop. for which spaceship, if either, does the kinetic energy change by a greater magnitude, and why?

Answers

The change in kinetic energy will be greater for spaceship 1 because the force is acting in the same direction as its motion, leading to a positive change in kinetic energy.

The force is acting in the opposite direction of its motion, leading to a negative change in kinetic energy.

The kinetic energy of an object is given by the formula

KE = (1/2)mv²

where

m is the mass of the object and

v is its velocity.

The change in kinetic energy is given by

ΔKE = KEf - KEi

where

KEf is the final kinetic energy and

KEi is the initial kinetic energy.

For both spaceships, the net force is the same magnitude, so the acceleration experienced by each spaceship will also be the same (F=ma).

However, the direction of the net force is different for each spaceship.

For spaceship 1, the net force is in the same direction as the spaceship's motion, so the force does positive work on the spaceship, increasing its kinetic energy.

The change in kinetic energy for spaceship 1 is

ΔKE1 = (1/2)m(v0 + at)² - (1/2)mv0²

         = (1/2)ma²t² + matv0.

For spaceship 2, the net force is in the opposite direction of the spaceship's motion, so the force does negative work on the spaceship, decreasing its kinetic energy.

The change in kinetic energy for spaceship 2 is

ΔKE2 = (1/2)m(v0 - at)² - (1/2)mv0²

          = (1/2)ma²t² - matv0.

Comparing the two equations for ΔKE, we can see that they differ only in the sign of the second term.

Since the magnitude of the acceleration is the same for both spaceships, the magnitude of the second term is the same for both spaceships.

However, the sign of the second term is opposite for each spaceship.

Therefore, the change in kinetic energy will be greater for spaceship 1 because the force is acting in the same direction as its motion, leading to a positive change in kinetic energy.

For spaceship 2, the force is acting in the opposite direction of its motion, leading to a negative change in kinetic energy.

To know more about kinetic energy refer here

brainly.com/question/26472013#

#SPJ11

An ice skater is spinning at 5.2 rev/s and has a moment of inertia of 0.24 kg-m2. 33% Calculate the angular momentum, in kilogram meters squared per second, of the ice skater spinning at 5.2 rev/s L1 7.84

Answers

The angular momentum of the ice skater spinning at 5.2 rev/s is 7.84kg-m2/s.

The formula for angular momentum is L = Iω, where I is the moment of inertia and ω is the angular velocity in radians per second.

To convert 5.2 rev/s to radians per second, we need to multiply by 2π, since there are 2π radians in one revolution:

5.2 rev/s * 2π rad/rev = 32.768 rad/s
So, the angular velocity of the ice skater is 32.768 rad/s.

Now, we can use the formula to calculate the angular momentum:

L = Iω
L = 0.24 kg-m2 * 32.768 rad/s
L = 7.84 kg-m2/s

Therefore, the angular momentum of the ice skater spinning at 5.2 rev/s is 7.84 kg-m2/s.

If you need to learn more about angular momentum click here:

https://brainly.com/question/30338110

#SPJ11

A transistor with β = 100 is biased to operate at a dc collector current of 0.5 mA. Find the values of g, rr, and re Repeat for a bias current of 50 μA.

Answers

Therefore, for a bias current of 0.5 mA, g ≈ 1.92 mA/V, rr ≈ 200 kΩ, and re ≈ 52 Ω. For a bias current of 50 μA, g ≈ 0.192 mA/V, rr ≈ 2 MΩ, and re ≈ 520 Ω.

To solve this problem, we can use the following equations for a common-emitter amplifier:

g = β * Ic / Vt

rr = Vaf / Ic

re = Vt / Ie

where β is the current gain, Ic is the collector current, Vt is the thermal voltage (≈ 26 mV at room temperature), Vaf is the early voltage, and Ie is the emitter current.

(a) For Ic = 0.5 mA:

g = β * Ic / Vt = 100 * 0.5 mA / 26 mV ≈ 1.92 mA/V

rr = Vaf / Ic (assume Vaf = 100 V) = 100 V / 0.5 mA = 200 kΩ

re = Vt / Ie (assume Ie ≈ Ic) = 26 mV / 0.5 mA ≈ 52 Ω

(b) For Ic = 50 μA:

g = β * Ic / Vt = 100 * 50 μA / 26 mV ≈ 0.192 mA/V

rr = Vaf / Ic (assume Vaf = 100 V) = 100 V / 50 μA = 2 MΩ

re = Vt / Ie (assume Ie ≈ Ic) = 26 mV / 50 μA ≈ 520 Ω

To know more about bias current,

https://brainly.com/question/17192941

#SPJ11

on its highest power setting, a microwave oven can increase the temperature of 0.425 kg of spaghetti by 45.0°c in 120 s.

Answers

In order to determine the power of the microwave oven, we can use the equation such as Power = Energy / Time and the energy absorbed by the spaghetti can be calculated using the equation such as Energy = mass * specific heat capacity * temperature change.

Given:

Mass of spaghetti (m) = 0.425 kg.

Temperature change (ΔT) = 45.0°C.

Time (t) = 120 s.

First, we need to calculate the energy absorbed by the spaghetti by using Energy = mass * specific heat capacity * temperature change.

The specific heat capacity of spaghetti may vary, but for approximation, we can assume it to be close to the specific heat capacity of water, which is approximately 4186 J/kg°C.

Energy = 0.425 kg * 4186 J/kg°C * 45.0°C.

Energy = 84913.5 J.

Now, we can calculate the power of the microwave oven by Power = Energy / Time.

Power = 84913.5 J / 120 s.

Power ≈ 707.6 W.

Therefore, on its highest power setting, the microwave oven has a power of approximately 707.6 watts.

Read more about Microwave ovens.

https://brainly.com/question/13623943

#SPJ11

ashley has a master's degree. based on this information alone, ashley cannot be a:

Answers

Based on the information provided, Ashley having a master's degree alone does not exclude any specific occupation or role. Ashley can potentially hold any job or profession, as having a master's degree is compatible with various career paths.

Having a master's degree does not exclude Ashley from any particular occupation or role. A master's degree is a postgraduate academic degree that can be pursued in various fields, including but not limited to business, education, arts, sciences, engineering, and more. The specific occupation or role that Ashley may hold would depend on the subject area of the master's degree and their individual interests, skills, and career choices. It is important to note that individuals with master's degrees can pursue a wide range of careers, including research, academia, management, consulting, healthcare, government, and many others, making it difficult to determine Ashley's specific occupation solely based on having a master's degree.

Learn more about master's degree here:

https://brainly.com/question/18897219

#SPJ11

determine the velocity of the 60kg block a, if the two blocks are released from rest, and the 40kg block b moves 2m up the incline.

Answers

In order to determine the velocity of block A, we need to analyze the conservation of mechanical energy in the system. Let's assume that the incline is frictionless and neglect any potential energy losses due to air resistance.

Mass of block A (m₁) = 60 kg.

Mass of block B (m₂) = 40 kg.

Distance moved by block B up the incline (d) = 2 m.

First, let's calculate the potential energy gained by block B as it moves up the incline:

Potential energy gained by block B = mass * gravity * height.

= m₂ * g * d.

Next, let's calculate the potential energy lost by block A as it moves down the incline:

Potential energy lost by block A = mass * gravity * height.

= m₁ * g * d.

Since the two blocks are connected by a rope, the potential energy lost by block A is transferred to block B as kinetic energy.

Therefore, we can equate the potential energy lost by block A to the potential energy gained by block B:

m₁ * g * d = m₂ * g * d.

Simplifying the equation by canceling out the common terms (g and d):

m₁ = m₂.

Since the masses are equal, the velocity of block A will be the same as the velocity of block B.

Therefore, the velocity of block A will be equal to the velocity of block B when block B reaches a height of 2 m up the incline.

Read more about Velocity.

https://brainly.com/question/19979064

#SPJ11

A 5m long aluminium wire (Y=7×10 10
Nm −2
) of diameter 3mm supports a 40kg mass. In order to have the same elongation in the copper wire (Y=12×10 10
Nm −2
) of the same length under the same weight, the diameter should now be (in mm).

Answers

The diameter of the copper wire should be 2.1 mm.

We can use the formula for the elongation (ΔL) of a wire under a weight (F) and with length (L), diameter (d) and Young's modulus (Y) to solve this problem. The formula is given by:

       ΔL = (FL) / (πd²Y)

We can start by using the formula to find the elongation of the aluminium wire. We know the length (L) is 5 m, the diameter (d) is 3 mm (0.003 m), the weight (F) is the weight of the mass, which is 40 kg times the acceleration due to gravity (9.81 m/s²), or 392.4 N, and the Young's modulus (Y) is 7×10¹⁰ Nm⁻². Substituting these values into the formula gives:

        ΔL = (FL) / (πd²Y)

        ΔL = (392.4 N × 5 m) / (π × (0.003 m)² × 7×10¹⁰ Nm⁻²)

        ΔL = 5.63×10⁻⁵ m

Now we want to find the diameter of the copper wire that will give the same elongation under the same weight and length. We can rearrange the formula to solve for the diameter (d):

        d = √((FL) / (πΔLY))

We know the length (L) is still 5 m, the weight (F) is still 392.4 N, and the Young's modulus (Y) for copper is 12×10¹⁰ Nm⁻². The only unknown is the elongation (ΔL), which we want to be the same as for the aluminium wire. Substituting the known values gives:

        d = √((FL) / (πΔLY))

        d = √((392.4 N × 5 m) / (π × 5.63×10⁻⁵ m × 12×10¹⁰ Nm⁻²))

        d = 0.0021 m

Converting this to millimeters gives the final answer of 2.1 mm.

For such more questions on diameter

https://brainly.com/question/28162977

#SPJ11

if the mass of body a and b are equal but ka = (1/3)kb, then ____________.

Answers

If the mass of body A and body B are equal, but the spring constant of the spring connected to body A, ka, is one-third (1/3) of kb, then the relationship between the two bodies can be explained using Hooke's Law and the concept of stiffness.

Hooke's Law states that the force exerted by a spring is directly proportional to the displacement of the spring from its equilibrium position. Mathematically, it can be expressed as:

F = -kx

Where:

F is the force exerted by the spring,

k is the spring constant, and

x is the displacement from the equilibrium position.

In this scenario, since the masses of bodies A and B are equal, the gravitational force acting on each body is the same. Therefore, we can focus on the forces exerted by the springs connected to these bodies.

According to Hooke's Law, for a given displacement from the equilibrium position, the force exerted by the spring is directly proportional to the spring constant. In other words, a spring with a higher spring constant exerts a stronger force for the same displacement compared to a spring with a lower spring constant.

Given that ka = (1/3)kb, it means that the spring connected to body A is less stiff (or less rigid) than the spring connected to body B. Since both bodies have equal masses, the force exerted by each spring will be equal when they are in equilibrium. However, for the same displacement, the spring with the higher spring constant (kb) will exert a greater force compared to the spring with the lower spring constant (ka).

In summary, the relationship between the two bodies can be understood as follows: When subjected to the same displacement, body B connected to the stiffer spring (kb) will experience a stronger force compared to body A connected to the less stiff spring (ka).

To know more about Hooke's Law, please click on:

https://brainly.com/question/30379950

#SPJ11

A sample of n = 25 is taken and the sample mean is x = 87 and a sample standard deviation of s= 20. Construct a 95% confidence interval for the true mean, u. A) (79.16, 94.84) B) (78.74, 95.26) C) (83.00, 91.00) D) (80.16, 93.84

Answers

Confidence Interval is : (78.74,95.26)

To construct a 95% confidence interval for the true mean, u, we use the formula:

CI = x ± (tα/2)(s/√n)

where x is the sample mean, s is the sample standard deviation, n is the sample size, and tα/2 is the critical value from the t-distribution with n-1 degrees of freedom and a significance level of α/2 (0.025 for a 95% confidence interval).

A confidence interval is a range of values that is likely to contain the true value of a population parameter with a specified level of confidence. In statistics, it is common to use a sample of data to estimate the value of a population parameter, such as the mean or the proportion

Plugging in the values from the problem, we get:

CI = 87 ± (2.064)(20/√25)
  = 87 ± 8.256
  = (78.744, 95.256)

Therefore, the answer is :

B) (78.74, 95.26).

To learn more about Standard Deviation, visit :

https://brainly.com/question/23907081

#SPJ11

Two small spheres have equal and opposite charges and are travelling parallel to each other with speed v to the right, as shown above. What is the direction of the magnetic field midway between the spheres at the instant shown? (A) Out of the page (B) Into the page (C) Toward the bottom of the page (D) Toward the top of the page (E) Undefined, since the magnitude of the magnetic field is zero.

Answers

Using this rule, we can see that the magnetic field at a point midway between the spheres will be directed out of the page. Therefore, the correct answer is (A) Out of the page.

The magnetic field midway between the spheres can be determined using the right-hand rule for the magnetic field around a current-carrying wire.

If we imagine a current flowing in the direction from the positively charged sphere to the negatively charged sphere (due to the flow of positive charge from one sphere to the other), then the direction of the magnetic field at a point midway between the spheres can be determined by curling the fingers of the right hand in the direction of the current, and the thumb will point in the direction of the magnetic field.

For more question on magnetic field click on

https://brainly.com/question/14411049

#SPJ11

The direction of the magnetic field midway between the spheres at the instant is  Out of the page. So the correct answer is (A) Out of the page.

The direction of the magnetic field midway between the spheres can be determined by applying the right-hand rule for the cross product of two vectors.

If we point the thumb of our right hand in the direction of the velocity of the positively charged sphere (to the right), and the fingers in the direction of the magnetic field, then the palm of our hand will point in the direction of the force on the positive charge.

Since the two spheres have equal and opposite charges, the force on the positively charged sphere will be to the left. Therefore, the direction of the magnetic field must be perpendicular to both the velocity of the positively charged sphere and the direction of the force on it, which is out of the page.

Learn more about magnetic field here:

https://brainly.com/question/23096032

#SPJ11

you push a 80-kg file cabinet to the right on a frictionless horizontal surface with a force of 175 n from rest, the cabinet moves a distance of 12 m. what is the final speed of the cabinet, in m/s?

Answers

The main answer to your question is that the final speed of the cabinet, in m/s, can be calculated using the equation:

final speed = (force x distance / mass)⁰°⁵



Plugging in the given values, we get:

final speed = (175 N x 12 m / 80 kg)⁰°⁵
final speed = (26.25 m²/s²)⁰°⁵
final speed = 5.124 m/s

Therefore, the final speed of the cabinet is 5.124 m/s.

The explanation behind this equation is that it comes from the formula for kinetic energy, which is KE = 0.5 x mass x velocity². By rearranging this equation and substituting the work done by the applied force (force x distance) for the kinetic energy, we get:

force x distance = 0.5 x mass x final speed²

Solving for final speed, we get the equation mentioned above. This equation tells us that the final speed of an object pushed by a force on a frictionless surface depends on the magnitude of the force, the distance traveled, and the mass of the object.

For more information on distance visit:

https://brainly.com/question/31713805

#SPJ11

The final speed of the file cabinet after moving 12 meters to the right with a force of 175 N on a frictionless horizontal surface is 7.24 m/s.

To solve this problem, we need to use the equation: force = mass x acceleration. Since the surface is frictionless, there is no force opposing the motion, so the entire force of 175 N is used to accelerate the file cabinet.
First, we need to calculate the acceleration of the cabinet using the equation: acceleration = force/mass. Plugging in the numbers, we get:
acceleration = 175 N / 80 kg = 2.1875 m/s^2
Next, we can use the kinematic equation: final speed^2 = initial speed^2 + 2 x acceleration x distance. Since the cabinet starts from rest, the initial speed is 0. Plugging in the numbers, we get:
final speed^2 = 0 + 2 x 2.1875 m/s^2 x 12 m
final speed^2 = 52.5 m^2/s^2
Taking the square root of both sides, we get:
final speed  sqrt(52.5) = 7.24 m/s
Therefore, the final speed of the file cabinet after moving 12 meters to the right with a force of 175 N on a frictionless horizontal surface is 7.24 m/s.

To know more about Frictionless horizontal surface visit:

https://brainly.com/question/26846158

#SPJ11

A block of mass 8.50 g on the end of spring undergoes simple harmonic motion with a frequency of 3.50 Hz. a) What is the spring constant of the spring? b) If the motion of the mass has an initial amplitude of 8.00 cm what is its maximum speed? c) The amplitude decreases to 1.600 cm in 5.14 s, what is the damping constant for the system?

Answers

The spring constant is 4.084 N/m, maximum speed is 1.76 m/s and damping constant is 0.0167 kg/s.

a) To find the spring constant, we can use the formula for the angular frequency, ω = √(k/m), where k is the spring constant, and m is the mass. Rearranging the formula, we get k = mω^2. The frequency f = 3.50 Hz, so ω = 2πf = 2π(3.50) = 22 rad/s. Given the mass m = 8.50 g = 0.0085 kg, we can find the spring constant: k = 0.0085 * (22)^2 = 4.084 N/m.
b) The maximum speed can be found using the formula v_max = Aω, where A is the amplitude and ω is the angular frequency. With an initial amplitude of 8.00 cm = 0.08 m, the maximum speed is v_max = 0.08 * 22 = 1.76 m/s.
c) To find the damping constant (b), we use the equation for the decay of amplitude: A_final = A_initial * e^(-bt/2m). Rearranging and solving for b, we get b = -2m * ln(A_final/A_initial) / t. Given A_final = 1.60 cm = 0.016 m, and the time t = 5.14 s, we find the damping constant: b = -2 * 0.0085 * ln(0.016/0.08) / 5.14 = 0.0167 kg/s.

To know more about spring constant visit:

https://brainly.com/question/14159361

#SPJ11

Other Questions
I'LL GIVE BRAINLIEST: ConiyaThe owner of Wayne's Auto Repair charges acustomer $285 for parts plus an hourly labor cost.The customer paid for 2.5 h of labor and paid a total of$490.What is the hourly labor cost?O $80.00 per hour$82.00 per hour0 $86.00 per hourO $89.00 per hour 7 ki power 2 Plus 8 ki 4 Each external force acts on the system for 10 seconds. Rank the change in momentum of each of the cart-cart systems from largest to smallest. (The label of m or 2 m desginates the relative mass of each cart.)It is possible to have some of the categories below BLANK since you may have items that are EQUAL to each other.Put the largest as far up as you can, and the smallest as far down as you can a molecure that contains 3 iddentical polar bonds to the central atom will be The Mexican government functions using a democratic system, while the Cuban government functions using which type of system? PLEASE HELPPPPPPPP I BEGGGG YOU Find the 11th term of the following sequence:-8, 24, -72,.... Solve for angle b and c I got 30 minutes left help me plsssThe Zhou kingdom was divided into __________.A.city-statesB.countriesC.feudal statesD.townsPlease select the best answer from the choices providedABCD The purpose of "crossing over" isA. to add genetic diversityB to pull the chromosomes away from each otherC to make identical copies of the parent cellD to help dissolve the nuclear membrane I need help quick I'll give brainliest! 1. The fare of 12 kg of luggage for a distance of 36km is 24 rupeesHow much fare will be charged for a luggage of 18kg for a distanceof 12km? help ASAP please !!Dorise is cutting a piece of fabric to use as a section of a patchwork quilt. A pattern of the quilt section is shown below.*Picture not drawn to scaleWhat is the area of section A? A. 28.5 square inches B. 49 square inches C. 24.5 square inches D. 14 square inches If an object is dropped from 100 feet in the air and air resistance is ignored, the object will fall at a rate that can be modeled by the function h(t) = -16t? + 100. After how many seconds is the object 20 feet from theground? What is a quinto drum?O A. A tom drumO B. A snare drumC. A bass drumO D. A conga drum 1. What is the authors view of gaming in the Point essay? Cite specific evidence from the essay to support your answer.2. What is the authors view of gaming in the Counterpoint essay? Be sure to use specific evidence from the text to support your answer.3. What is the authors view of gaming in the Counterpoint essay? Be sure to use specific evidence from the text to support your answer. what is a local self government If you are given a chance to follow a political ideology, which political ideology will you choose? Why? Which worm shown is most likely a segmented worm?