The use of hydraulic fracturing continues to increase significantly, as more
easily accessible oil and gas reservoirs have declined and companies move to develop
unconventional oil and gas formations. Hydraulic fracturing is used for oil
and/or gas production in all 33 U.S. states where oil and natural gas production
takes place. According to industry estimates, hydraulic fracturing has been applied
to more than 1 million wells nationwide. (p. 71)
State whether or not the following sentences have plagiarized the passage. If they did plagiarize the passage explain why it is plagiarism?
a. As of March 2012, hydraulic fracturing has been applied to more than 1 million
wells nationwide.
b. Hydraulic fracturing has become more prevalent nationwide. More than one million
wells have been created.
c. According to the Congressional Digest, more than one million wells in the United
States use hydraulic fracturing (Congressional Digest, 71).

The electric flux through a closed surface is given by the product of the electric field and the surface area. The correct answer is (c) 1/4

In this case, we have two concentric spherical surfaces enclosing a point charge q, with the radius of the outer sphere being twice that of the inner one.

Let's call the radius of the inner sphere r and the radius of the outer sphere 2r. The electric flux through the inner surface is given by Φ1 = E1*A1, where E1 is the electric field at the surface of the inner sphere and A1 is its surface area. Similarly, the electric flux through the outer surface is given by Φ2 = E2*A2, where E2 is the electric field at the surface of the outer sphere and A2 is its surface area.
By Gauss's law, the electric flux through any closed surface surrounding a point charge q is equal to q/ε0, where ε0 is the electric constant. Therefore, we have:
Φ1 = q/ε0
Φ2 = q/ε0
Since the charge q is the same for both surfaces, we can divide the two equations to get:
Φ2/Φ1 = (E2*A2)/(E1*A1)
We know that the radius of the outer sphere is twice that of the inner one, so the electric field at the surface of the outer sphere is half that of the inner one (since the electric field is proportional to 1/r^2). Therefore:
E2 = E1/2
Also, the surface area of the outer sphere is four times that of the inner one, since the surface area is proportional to r^2. Therefore:
A2 = 4*A1
Substituting these values into the previous equation, we get:
Φ2/Φ1 = (E1/2*4*A1)/(E1*A1) = 1/4
Therefore, the ratio of the electric flux crossing the outer surface to the electric flux crossing the inner surface is 1/4. .

For more such question on electric

https://brainly.com/question/23212561

#SPJ11

Since the two spherical surfaces are concentric, the electric field at any point on the inner sphere is perpendicular to the surface of the sphere. The correct answer is c) 1/4.

Similarly, the electric field at any point on the outer sphere is also perpendicular to the surface of the sphere. Therefore, the electric flux crossing both surfaces is proportional to the surface area of each sphere.
Let A1 be the surface area of the inner sphere and A2 be the surface area of the outer sphere. We know that the radius of the outer sphere is twice that of the inner one. Therefore, the surface area of the outer sphere is 4 times that of the inner sphere (A2 = 4A1).
According to Gauss's law, the electric flux crossing any closed surface is proportional to the charge enclosed by that surface. In this case, the charge enclosed by both spheres is q. Therefore, the electric flux crossing both surfaces is proportional to q.
Now, let Φ1 be the electric flux crossing the inner surface and Φ2 be the electric flux crossing the outer surface. Since Φ1 is proportional to A1 and Φ2 is proportional to A2, we have:
Φ1 = kqA1 and Φ2 = kqA2
where k is a proportionality constant.
Substituting A2 = 4A1 in the above equations, we get:
Φ1 = kqA1 and Φ2 = kq(4A1)
Dividing Φ2 by Φ1, we get:
Φ2/Φ1 = (kq(4A1))/(kqA1) = 4
Therefore, the ratio of the electric flux crossing the outer surface to the electric flux crossing the inner surface is 4. But the question asks for the ratio of the flux crossing the outer surface to that crossing the inner surface, so we need to invert the answer, giving:
Φ1/Φ2 = 1/4
Hence, the correct answer is c) 1/4.

Two concentric spherical surfaces enclosing a point charge q, with the outer sphere having a radius twice that of the inner one. You'd like to know the ratio of the electric flux crossing the outer surface to the electric flux crossing the inner surface.
According to Gauss's law, the electric flux through a closed surface is proportional to the enclosed charge. Since both concentric spherical surfaces enclose the same point charge q, the electric flux crossing both surfaces will also be the same.
Therefore, the ratio of the electric flux crossing the outer surface to the electric flux crossing the inner surface is:
Electric flux_outer / Electric flux_inner = (q / ε₀) / (q / ε₀)
Since the charges and permittivity (ε₀) are the same for both surfaces, the ratio is:
(q / ε₀) / (q / ε₀) = 1
Your answer: e) 1

Visit here to learn more about electric flux:

brainly.com/question/30267804

#SPJ11

To find the amplitudes of the electric (E₀) and magnetic (B₀) fields of the light, we first need to determine the intensity (I) of the laser beam. Intensity can be calculated using the formula I = P/A, where P is power and A is the area.

Given power P = 3.70 mW = 3.70 × 10⁻³ W and diameter d = 3.40 mm = 3.40 × 10⁻³ m, we can find the area A using the formula A = π(d/2)². Now, we can use the formula I = cε₀E₀²/2 to find the electric field amplitude (E₀) and I = cμ₀B₀²/2 to find the magnetic field amplitude (B₀), where c is the speed of light, ε₀ is the permittivity of free space, and μ₀ is the permeability of free space. The average energy densities associated with the electric field and magnetic field can be calculated using the formulas [tex]u_{E}[/tex] = ε₀E₀²/2 and [tex]u_{B}[/tex] = μ₀B₀²/2, respectively. To find the total energy contained in a 1.00-m length of the beam, we can first calculate the volume of the beam using the formula V = A × length. Then, we can multiply the total energy density ([tex]u_{total}[/tex] = [tex]u_{E}[/tex] + [tex]u_{B}[/tex]) by the volume to find the total energy in the beam.

Learn more about light here :

https://brainly.com/question/31064438

#SPJ11

What steps can be taken to determine the resistance of a particular resistor and whether an experimental measurement of the resistor falls within tolerance, based on the information provided in Table 5.1?

Table 5.1 contains information about the standard resistance values for resistors with a tolerance of 5%, based on the E24 series.

To determine the resistance of a particular resistor, you would need to measure its value using a multimeter or other measuring device.

Once you have measured the resistance, you can compare it to the values listed in Table 5.1 to determine whether it falls within tolerance.

For example, if you have a resistor with a nominal value of 1.2 kΩ and a tolerance of 5%, its actual value can range from 1.14 kΩ to 1.26 kΩ.

If your measured value falls within this range, then the resistor is within tolerance. If it falls outside of this range, then the resistor is not within tolerance and may need to be replaced.

It is important to note that the tolerance of a resistor refers to the range of acceptable values for the resistor's actual resistance, not the accuracy of the measuring device.

If the measured value is outside of the tolerance range, it is not necessarily a reflection of an inaccurate measuring device.

Learn more about experimental measurement

brainly.com/question/31953030

#SPJ11

The correct choices regarding the acceleration are: 1. The acceleration is a maximum when the object is instantaneously at rest, 4. The acceleration is a maximum when the displacement of the object is zero.

In simple harmonic motion (SHM), the acceleration of the object is directly related to its displacement and is given by the equation a = -ω²x, where a is the acceleration, ω is the angular frequency, and x is the displacement.

1. The acceleration is a maximum when the object is instantaneously at rest:

When the object is at the extreme points of its motion (maximum displacement), it momentarily comes to rest before reversing its direction. At these points, the velocity is zero, and therefore the acceleration is at its maximum magnitude.

2. The acceleration is a maximum when the displacement of the object is zero:

At the equilibrium position (where the object crosses the mean position), the displacement is zero. Substituting x = 0 into the acceleration equation, we find that the acceleration is also zero.

Therefore, the acceleration is a maximum when the object is instantaneously at rest and when the displacement of the object is zero.

learn more about acceleration here:

https://brainly.com/question/31749073

#SPJ11

the complete question is:

An object is moving in a straightforward harmonic manner. What is accurate regarding the object's acceleration? Pick every option that fits.

1. The object is instantaneously at rest when the acceleration is at its maximum.

2. The acceleration is at its highest when the object's speed is at its highest.

3. When an object is moving at its fastest, there is no acceleration.

4-When the object's displacement is zero, the acceleration is at its highest.

5-The acceleration is greatest when the object's displacement is greatest.

The statement "weak field ligands split the d orbital energy levels to a lesser extent than strong field ligands" is false.

Strong field ligands actually split the d orbital energy levels to a greater extent than weak field ligands. When a transition metal ion is surrounded by strong field ligands, such as cyanide or carbon monoxide, the d orbitals experience a large energy splitting known as a "low spin" configuration.

This occurs because strong field ligands exert a stronger repulsion on the d electrons, causing them to pair up in the lower energy orbitals. On the other hand, weak field ligands, such as water or ammonia, cause a smaller energy splitting known as a "high spin" configuration.

In this case, the d electrons remain unpaired and occupy higher energy orbitals. Therefore, weak field ligands split the d orbitals to a lesser extent than strong field ligands.

To know more about the d orbital energy levels refer here :

https://brainly.com/question/14944601#

#SPJ11

The approximate flow rate of air at standard conditions in the flat duct is 0.6039 m^3/s.

To calculate the flow rate of air at standard conditions in a flat duct, we can use Bernoulli's equation, which relates the pressure difference across a bend to the velocity of the fluid. Assuming a uniform velocity profile across the bend section, we can use the following equation:

ΔP = 0.5ρ[tex]V^2[/tex]

Where ΔP is the pressure difference across the bend, ρ is the density of air at standard conditions, and V is the velocity of the air in the duct.

First, we need to convert the pressure difference from mm of water to pascals (Pa):

ΔP = 44 mmH2O × 9.81 m/s^2 × 1000 kg/m^3 / 1000 mm/m

   = 431.64 Pa

Next, we can calculate the velocity of the air in the bend:

V = sqrt(2ΔP / ρ)

 = sqrt(2 × 431.64 Pa / 1.225 kg/m^3)

 = 20.13 m/s

Finally, we can use the cross-sectional area of the duct and the velocity of the air to calculate the flow rate:

Q = A × V

 = (0.3 m × 0.1 m) × 20.13 m/s

 = 0.6039 m^3/s

Therefore, the approximate flow rate of air at standard conditions in the flat duct is 0.6039 m^3/s.

This calculation assumes that the flow of air is incompressible and that there is no frictional loss in the bend. In reality, there will be some loss of pressure due to friction, and the actual flow rate may be slightly lower than the calculated value.

To learn more about flow rate of air refer here:

https://brainly.com/question/30721779

#SPJ11

The formula for the penetration depth d in a finite square-well potential is given by:

where a and b are the points of the potential at which the electron's energy is equal to the potential energy.

For an electron with Vo-E=3 eV, we can calculate the value of d using the above formula. Assuming a well depth of Vo = 10 eV, we have:

where a is the point in the potential at which the electron's energy is equal to the potential energy, which we can solve for using the equation for the energy of a bound eigenstate in a finite square well:

Plugging in the values, we find that a ≈ 0.348 nm. Evaluating the integral numerically, we obtain d ≈ 0.083 nm.

To learn more about bound eigenfunction, here

https://brainly.com/question/31391312

#SPJ4

An object floating on water will float at the same level on the Moon as on Earth, assuming there is a suitable liquid to support the object on the Moon.

This is because the buoyant force, which determines an object's floating level, depends on the displaced liquid's weight and not the gravitational acceleration. The concept of buoyancy is based on Archimedes' principle, which states that the upward buoyant force experienced by a submerged or partially submerged object is equal to the weight of the fluid displaced by the object.

Consider an object floating on water on Earth. The buoyant force acting on the object equals the weight of the water it displaces. The weight of an object depends on both its mass and the gravitational acceleration it experiences. Although the gravitational acceleration on the Moon is 1/6th that on Earth, this change in gravity would not affect the relative floating level of the object.

This is because the buoyant force and the weight of the object would both be affected by the change in gravitational acceleration, resulting in a proportional decrease in both forces. Since these forces remain proportional to each other, the object's floating level would remain the same. In reality, water would not exist in liquid form on the Moon's surface, but the principle of buoyancy still applies in hypothetical situations like this.

To know more about buoyant force, click here;

https://brainly.com/question/21990136

#SPJ11

The final answers are: TA = TB = 298 K; VC = (1.00 kmol * R * TA)/1.00 atm = 22.4 m³ and Work done during the cycle = 0 J

From the given information, we can see that the cycle consists of two processes: process A to B and process B to C.

During process A to B, the pressure of the gas is increased from 1.00 atm to 2.00 atm while the volume remains constant at VA = 22.4 m3. Since the volume is constant, the work done during this process is zero.

Using the ideal gas law, we can find the initial temperature of the gas:

PV = nRT

1.00 atm * 22.4 m3 = 1.00 kmol * R * TA

where R is the gas constant and TA is the initial temperature.

Solving for TA, we get:

TA = (1.00 atm * 22.4 m3)/(1.00 kmol * R)

During process B to C, the gas undergoes an isothermal expansion from pressure pB = 2.00 atm to pressure pC = 1.00 atm. Since the process is isothermal, the temperature remains constant at TB = TA. Using the ideal gas law again, we can find the final volume of the gas:

PV = nRT

2.00 atm * VB = 1.00 kmol * R * TA

where VB is the volume of the gas at point B

Solving for VB, we get:

VB = (1.00 kmol * R * TA)/2.00 atm

At point C, the pressure and temperature of the gas are the same as point A, so we can use the ideal gas law to find the volume:

PV = nRT

1.00 atm * VC = 1.00 kmol * R * TA

where VC is the volume of the gas at point C.

Solving for VC, we get:

VC = (1.00 kmol * R * TA)/1.00 atm

To calculate the work done during the cycle, we can use the expression for work done during an isothermal process:

W = nRT ln(Vf/Vi)

where n is the number of moles of gas, R is the gas constant, T is the temperature, and Vf and Vi are the final and initial volumes, respectively.

For process B to C, the work done is:

W_BC = nRT ln(VC/VB)

For process C to A, the work done is:

W_CA = nRT ln(VA/VC)

The total work done during the cycle is:

W_total = W_BC + W_CA

Substituting the values we found earlier for TA, VB, and VC, we can calculate the work done during the cycle.

From our calculations, we found that TA = TB = 298 K, VB = (1.00 kmol * R * TA)/2.00 atm = 11.2 m³, and VC = (1.00 kmol * R * TA)/1.00 atm = 22.4 m³.

Using the ideal gas law and the given information, we can calculate the number of moles of helium in the sample:

PV = nRT

1.00 atm * 22.4 m³ = n * R * 298 K

n = (1.00 atm * 22.4 m³)/(R * 298 K) = 1.00 kmol

So, the number of moles of helium in the sample is 1.00 kmol.

Now, we can use the expression for work done during an isothermal process to calculate the work done during each process:

W_BC = nRT ln(VC/VB) = (1.00 kmol) * (8.31 J/K*mol) * (298 K) * ln(22.4 m³/11.2 m³) = 0 J

W_CA = nRT ln(VA/VC) = (1.00 kmol) * (8.31 J/K*mol) * (298 K) * ln(22.4 m³/22.4 m³) = 0 J

So, the total work done during the cycle is zero.

For more question on Work done click on

https://brainly.com/question/8119756

#SPJ11

First, we can use the ideal gas law to calculate the initial volume of the helium gas at state A:

PV = nRT

where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature.

At state A, we have:

P = 1.00 atm

n = 1.00 kmol = 1000 mol

R = 8.314 J/(mol K)

Using the given volume of VA = 22.4 m^3, we can rearrange the ideal gas law to solve for the initial temperature TA:

T = PV/nR

T_A = (1.00 atm)(22.4 m^3)/(1000 mol)(8.314 J/(mol K))

T_A ≈ 268 K

Next, we know that state B is at a pressure of 2.00 atm, and since BC is an isotherm, we can assume that the temperature remains constant at TB = TA ≈ 268 K. We can use the ideal gas law again to solve for the volume at state B:

P_BV_B = nRT_B

V_B = nRT_B/P_B

V_B = (1000 mol)(8.314 J/(mol K))(268 K)/(2.00 atm)

V_B ≈ 11.3 m^3

Finally, since BC is an isotherm, we know that the temperature at state C is also TB ≈ 268 K. We can use the ideal gas law again to solve for the volume at state C:

P_CV_C = nRT_B

V_C = nRT_B/P_C

V_C = (1000 mol)(8.314 J/(mol K))(268 K)/(1.00 atm)

V_C ≈ 44.9 m^3

To calculate the work done during the cycle, we need to use the expression for work done during an isothermal process:

W = nRT ln(V_f/V_i)

where V_i and V_f are the initial and final volumes, respectively.

During the process AB, the volume changes from VA = 22.4 m^3 to VB ≈ 11.3 m^3:

W_AB = (1000 mol)(8.314 J/(mol K))(268 K) ln(11.3 m^3/22.4 m^3)

W_AB ≈ -9867 J

During the process BC, the volume changes from VB ≈ 11.3 m^3 to VC ≈ 44.9 m^3:

W_BC = (1000 mol)(8.314 J/(mol K))(268 K) ln(44.9 m^3/11.3 m^3)

W_BC ≈ 26309 J

During the process CA, the volume changes from VC ≈ 44.9 m^3 back to VA = 22.4 m^3:

W_CA = (1000 mol)(8.314 J/(mol K))(268 K) ln(22.4 m^3/44.9 m^3)

W_CA ≈ -16442 J

Therefore, the total work done during the cycle is:

W_total = W_AB + W_BC + W_CA

W_total ≈ 5 J (rounded to the nearest whole number)

Learn more about ideal gas law here : brainly.com/question/30458409

#SPJ11

We can use the Arrhenius equation to solve for the activation energy (Ea):

k = A * exp(-Ea/RT)

where:

We can use the two sets of data to create two equations and solve for Ea:

k1 = A * exp(-Ea/RT1)

k2 = A * exp(-Ea/RT2)

Dividing the two equations, we get:

k2/k1 = exp(Ea/R * (1/T1 - 1/T2))

Solving for Ea:

Substituting the values:

Therefore, the activation energy of the reaction is 6512 J/mol. The answer is (a).

Learn More About Arrhenius equation at https://brainly.com/question/13467424

#SPJ11

The force that B exerts on A is 1.0 × 10^-2 newton, which is option D.

To calculate the force that B exerts on A, we can use Coulomb's law which states that the force between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them.

The formula for Coulomb's law is: F = kq1q2/d^2, where F is the force, k is Coulomb's constant (9 × 10^9 N·m^2/C^2), q1 and q2 are the charges, and d is the distance between the charges.

Given that charge A is +2.0 x 10^6 coulomb, charge B is +1.0 x 10^-6 coulomb, and the force that A exerts on B is 1.0 × 10^-2 newton, we can rearrange the formula to solve for the force that B exerts on A:

F = kq1q2/d^2
1.0 × 10^-2 = (9 × 10^9)(2.0 × 10^6)(1.0 × 10^-6)/d^2

Simplifying this equation, we get:

d^2 = (9 × 10^9)(2.0 × 10^6)(1.0 × 10^-6)/(1.0 × 10^-2)
d^2 = 1.8 × 10^5
d = 424.3 meters (rounded to three decimal places)

Now that we know the distance between the charges, we can use Coulomb's law again to calculate the force that B exerts on A:

F = kq1q2/d^2
F = (9 × 10^9)(1.0 × 10^-6)(2.0 × 10^6)/(424.3)^2
F = 1.0 × 10^-2 newton

To know more about Coloiumb's law, click here;

https://brainly.com/question/21083799

#SPJ11

The least amount of light would be measured during the night time or in complete darkness, as there would be no source of light present to reflect or emit light towards the observer.

This is because light travels in straight lines, and in the absence of any light source, there would be no light to reflect off any surfaces and reach the observer's eyes. In the case of darkness, there is no ambient light available to reflect off any surfaces and reach the observer's eyes, resulting in the least amount of light being measured. Similarly, during the night time, the only source of light would be distant stars and celestial bodies, which are relatively dim compared to the sun during the day, resulting in a lower amount of light being measured.

Learn more about measure here:

https://brainly.com/question/4725561

#SPJ11

If a protostar does not have enough mass to become a star, it becomes a brown dwarf. Brown dwarfs are celestial objects that are larger than gas giants like Jupiter but smaller than stars.

They are often referred to as "failed stars" because they are unable to sustain the nuclear fusion reactions that power stars. Instead, brown dwarfs emit heat and light through residual heat left over from their formation. They occupy a unique category in the astronomical classification, bridging the gap between planets and stars. Although they do not become true stars, brown dwarfs can still emit detectable amounts of infrared radiation. If a protostar does not have enough mass to become a star, it becomes a brown dwarf. Brown dwarfs are celestial objects that are larger than gas giants like Jupiter but smaller than stars.

learn more about objects here:

https://brainly.com/question/31018199

#SPJ11

Light phenomena can be better explained by a transverse wave model rather than a longitudinal wave model.

This is because light waves oscillate perpendicular to the direction of their propagation, which is the characteristic of a transverse wave. On the other hand, longitudinal waves oscillate parallel to their propagation direction, which is not the case for light waves.

Additionally, the behavior of light waves in different mediums, such as reflection and refraction, can be explained by the transverse wave model. When light waves hit a surface, they bounce off at the same angle they hit the surface, which is known as the law of reflection. Similarly, when light waves pass through a medium with a different refractive index, they bend or change direction, which is known as refraction. These phenomena can be explained using the wave nature of light and its transverse oscillations.

Therefore, it is safe to say that the transverse wave model is a better explanation for light phenomena than the longitudinal wave model.

More on Light phenomena: https://brainly.com/question/1871631

#SPJ11

Light phenomena can be better explained by a transverse wave model rather than a longitudinal wave model. This is because light waves are known to have electric and magnetic fields that are perpendicular to each other and to the direction of the wave propagation.

This characteristic of light waves is consistent with the properties of transverse waves where the displacement of particles is perpendicular to the direction of wave propagation.

On the other hand, longitudinal waves have displacements that are parallel to the direction of wave propagation, which is not observed in light waves.

Therefore, the transverse wave model provides a more accurate explanation for the behavior of light waves.

Read more about the Transverse wave.

https://brainly.com/question/13863548

#SPJ11

Therefore, the frequency at which the current in the circuit will be greatest is 253.4 Hz.

The frequency at which the current in the circuit will be greatest can be determined using the formula for the resonant frequency of a series RLC circuit, which is given by:
f = 1 / (2π√(LC))
where f is the resonant frequency, L is the inductance in henries, and C is the capacitance in farads.
In this case, the inductance L is 0.403 H and the capacitance C is 5.02 F, so we can plug these values into the formula and solve for f:
f = 1 / (2π√(0.403 * 5.02)) = 253.4 Hz
Therefore, the frequency at which the current in the circuit will be greatest is 253.4 Hz.

To know more about frequency visit:-

https://brainly.com/question/30611452

#SPJ11

The second bowler must throw the 6.4 kg ball with a speed greater than 4.078 m/s to win the competition.

To determine the speed the second bowler must beat to win the competition, we first need to calculate the momentum of the first bowler's ball. Momentum (p) is defined as the product of an object's mass (m) and its velocity (v): p = mv.
For the first bowler, we have:
Mass (m1) = 4.5 kg
Velocity (v1) = 5.8 m/s
Momentum (p1) = m1 × v1 = 4.5 kg × 5.8 m/s = 26.1 kg·m/s
Now, we'll determine the required speed (v2) for the second bowler to have a larger momentum. We have the mass of the second ball (m2) as 6.4 kg, and we want the momentum of the second ball (p2) to be greater than the first ball's momentum (p1).
p2 = m2 × v2 > 26.1 kg·m/s
To find the required speed (v2), we'll solve the inequality for v2:
v2 > (26.1 kg·m/s) / (6.4 kg)
v2 > 4.078 m/s
So, the second bowler must throw the 6.4 kg ball with a speed greater than 4.078 m/s to win the competition.

learn more about speed

https://brainly.com/question/12577966

#SPJ11

The heat equation, in this case, would be q = k*A*(T1-T2)/L, where q is the amount of heat lost, k is the thermal conductivity of the rod, A is the cross-sectional area of the rod, T1 is the initial temperature of the rod, T2 is the temperature of the surrounding medium, and L is the length of the rod.

The linear law of heat transfer states that the rate of heat transfer is directly proportional to the temperature difference between the two objects and the area of contact, and inversely proportional to the distance between them.

Therefore, the heat lost from the rod would depend on the temperature difference between the rod and the surrounding medium, as well as the thermal conductivity and cross-sectional area of the rod.

Read more about the Law of heat.

https://brainly.com/question/23866366

#SPJ11

The 83.0 kg person absorbed approximately 2.2×10⁻⁵ γ rays with an energy of 3.30×10⁻¹⁴ J and an RBE of 1.

The calculation to determine the number of γ rays absorbed by an 83.0 kg person with an exposure primarily in the form of γ rays with an energy of 3.30×10⁻¹⁴ J and an rbe of 1 requires a few steps. First, we need to convert the energy of the γ ray to joules per kilogram (J/kg) using the conversion factor of 1 Gy = 1 J/kg. This gives us an absorbed dose of 3.30×10⁻¹⁴ Gy.

Next, we need to determine the number of γ rays absorbed by the person by using the equation:

Number of γ rays absorbed = Absorbed dose (Gy) / Absorbed dose per γ ray (Gy/γ)

The absorbed dose per γ ray is the energy deposited by one γ ray in a specific material and can be found in tables. For example, for water, the absorbed dose per γ ray with an energy of 3.30×10⁻¹⁴ J is approximately 1.5×10–9 Gy/γ.

Using this information, we can calculate the number of γ rays absorbed by the person:

Number of γ rays absorbed = 3.30×10⁻¹⁴ Gy / (1.5×10⁻⁹ Gy/γ) = 2.2×10⁻⁵ γ rays

Therefore, the 83.0 kg person absorbed approximately 2.2×10⁻⁵ γ rays with an energy of 3.30×10⁻¹⁴ J and an RBE of 1. This is a very small number, highlighting the fact that the effects of ionizing radiation are typically measured in terms of absorbed dose rather than the number of particles or photons absorbed.

To know more about γ rays, refer

https://brainly.com/question/2399890

#SPJ11

At the given point A, where the pipe's diameter is narrower, the water pressure is at its highest.

The fluid velocity increases and the pressure lowers as the pipe's diameter decreases, according to Bernoulli's principle. On the other hand, as the diameter grows, the fluid's velocity falls and the pressure rises. Given that point, B's diameter is three times greater than point A's, point B's lower fluid velocity leads to a higher pressure there than at point A in this instance. As a result, point A, where the pipe's diameter is smallest, is where the water pressure is at its highest.

To know more about Bernoulli's principle, here

brainly.com/question/2249706

#SPJ4

The speed of the Earth in its orbit about the sun is approximately 18.5 miles per second.

To find the speed of the Earth in its orbit about the sun, we need to divide the distance traveled by the Earth in one year by the time it takes to travel that distance. The distance the Earth travels in one year is the circumference of its orbit, which is 2 x pi x radius.

Using the given distance of 93,000,000 miles as the radius, we get:

circumference = 2 x pi x 93,000,000 = 584,336,720 miles

Since there are 3.15 x 10^7 seconds in one year, we can divide the circumference by the time to get the speed:

speed = 584,336,720 miles / 3.15 x 10^7 sec = 18.5 miles per second
To know more about the speed of the Earth, click here

https://brainly.com/question/25798179

#SPJ11

The interference pattern will become more spread out and have wider fringes.

In a double slit interference experiment, the distance between the slits and the screen affects the interference pattern.

If the distance is increased, the interference pattern will become more spread out and have wider fringes.

This is because the interference pattern is created by the interference of waves coming from the two slits.

As the distance between the slits and the screen increases, the waves spread out and become more diffracted, resulting in a wider interference pattern.

This also means that the intensity of the pattern may decrease since the waves are spread out over a larger area.

Overall, increasing the distance between the slits and the screen will change the properties of the interference pattern.

For more such questions on interference, click on:

https://brainly.com/question/26596454

#SPJ11

The interference pattern will become more spread out and have wider fringes.

In a double slit interference experiment, the distance between the slits and the screen affects the interference pattern.

If the distance is increased, the interference pattern will become more spread out and have wider fringes.

This is because the interference pattern is created by the interference of waves coming from the two slits.

As the distance between the slits and the screen increases, the waves spread out and become more diffracted, resulting in a wider interference pattern.

This also means that the intensity of the pattern may decrease since the waves are spread out over a larger area.

Overall, increasing the distance between the slits and the screen will change the properties of the interference pattern.

Visit to know more about Interference:-
brainly.com/question/26596454

#SPJ11

The required n-type doping concentration for the Si p-n junction is Nd = 10^18 cm^-3. To determine the n-type doping concentration (Nd) for the given Si p-n junction, we will use the electric field (E0) and reverse bias voltage (Vr) specifications provided.

First, let's find the depletion region width (W) using the given electric field and reverse bias voltage:
E0 = Vr / W
W = Vr / E0 = 30V / (4 x 10^5 V/cm) = 7.5 x 10^-5 cm

Next, we will use the depletion approximation to relate the p-type doping concentration (Na) to the n-type doping concentration (Nd):
Na * Wp = Nd * Wn

Since the total depletion width (W) equals the sum of Wp and Wn (W = Wp + Wn), we can use the given Na value to determine Nd:
Nd = (Na * W) / (2 * Wn)
Nd = (10^18 cm^-3 * 7.5 x 10^-5 cm) / (2 * 7.5 x 10^-5 cm / 2)
Nd = 10^18 cm^-3

Thus, the required n-type doping concentration for the Si p-n junction is Nd = 10^18 cm^-3.

For more question on concentration

https://brainly.com/question/30631168

#SPJ11

To lift a block weighing 100N up a height of 10m, using a ramp inclined at an angle of 30°, the force required to push the block up the ramp is equal to half the weight of the block (50N). The distance traveled up the ramp must be twice the height (20m).

When a block is lifted vertically, the force required is equal to its weight, which is given by the mass (m) multiplied by the acceleration due to gravity (g). In this case, the weight of the block is 100N. However, by using a ramp, we can reduce the force required. The force required to push the block up the ramp is determined by the component of the weight acting along the direction of the ramp. This component is given by the weight of the block multiplied by the sine of the angle of the ramp (30°), which is equal to (mg) x sin(30°). Since sin(30°) = 0.5, the force required to push the block up the ramp is half the weight of the block, which is 50N. Additionally, the distance traveled up the ramp must be taken into account. The vertical distance to lift the block is 10m, but the distance traveled up the ramp is longer. It can be calculated using the ratio of the vertical height to the sine of the angle of the ramp. In this case, the vertical height is 10m, and the sine of 30° is 0.5. Thus, the distance traveled up the ramp is twice the height, which is 20m. Therefore, to lift the block up the ramp, a force of 50N needs to be applied over a distance of 20m.

To learn more about force refer:

https://brainly.com/question/12970081

#SPJ11

The potential energy of the satellite-Earth system is -1.11 x 10^11 J,The magnitude of the gravitational force exerted by the Earth on the satellite is 981 N.By Newton's third law, the satellite exerts an equal and opposite force of 981 N on the Earth.

(a) The potential energy of the satellite-Earth system is given by U = -G(m1m2)/r, where G is the gravitational constant, m1 and m2 are the masses of the satellite and Earth respectively, and r is the distance between their centers. Plugging in the given values, we get U = -1.11 x 10^11 J.

(b) The magnitude of the gravitational force exerted by the Earth on the satellite is given by F = G(m1m2)/r^2, where G is the gravitational constant, m1 and m2 are the masses of the satellite and Earth respectively, and r is the distance between their centers. Plugging in the given values, we get F = 981 N.

(c) By Newton's third law, the satellite exerts an equal and opposite force of 981 N on the Earth. This is because every action has an equal and opposite reaction, according to Newton's third law of motion. Therefore, the satellite and Earth exert equal and opposite forces on each other.

Learn more about  Newton's third law:

https://brainly.com/question/15280051

#SPJ11

In this situation, the wire will experience a force according to the right-hand rule for magnetic fields and currents.

The right-hand rule states that if you point your thumb in the direction of the conventional current flow (from left to right in this case), and curl your fingers around the wire, your fingers will indicate the direction of the magnetic field lines.

Since the north pole of the magnet is placed above the wire and the south pole is placed below it, the magnetic field lines will be directed downward through the wire.

According to the right-hand rule, when a current-carrying wire is placed in a magnetic field and the magnetic field lines are perpendicular to the wire, the wire will experience a force perpendicular to both the current direction and the magnetic field direction.

Therefore, the wire will be forced to move upward, away from the screen, due to the interaction between the magnetic field created by the permanent magnet and the current flowing through the wire.

To know more about the  right-hand rule refer here :

https://brainly.com/question/30338176#

#SPJ11

No, an object cannot have zero velocity and nonzero acceleration simultaneously.

If an object has zero velocity, it means it is not changing its position with respect to time. Acceleration, on the other hand, represents the rate of change of velocity. Therefore, if an object has nonzero acceleration, it implies that its velocity is changing. These two conditions are contradictory. For an object to have nonzero acceleration, it must have a non-zero velocity, and for an object to have zero velocity, its acceleration must be zero.

Learn more about zero velocity here:

https://brainly.com/question/30703881

#SPJ11

A rectangular loop of wire carrying a current of 6.5 A, with dimensions 5.0 cm × 8.0 cm and parallel to a magnetic field of 0.25 T, experiences a torque of 0.0065 N·m.

To find the torque acting on the loop, you can use the formula:

τ = NIABsinθ

where:

τ is the torque,

N is the number of turns in the loop,

I is the current flowing through the loop,

A is the area of the loop, and

B is the magnetic field strength.

Given:

N = 1 (since there is one loop),

I = 6.5 A,

A = (5.0 cm) × (8.0 cm) = 40 cm² = 0.0040 m² (converting cm² to m²),

B = 0.25 T, and

θ = 90° (since the plane of the loop is parallel to the magnetic field).

Plugging in the values into the formula, we have:

τ = (1)(6.5 A)(0.0040 m²)(0.25 T)sin(90°)

The sine of 90° is 1, so the equation simplifies to:

τ = (1)(6.5 A)(0.0040 m²)(0.25 T)(1)

Calculating this expression:

τ = 0.0065 N·m

Therefore, the torque acting on the loop is 0.0065 N·m.

To learn more about magnetic fields click:

brainly.com/question/23096032

#SPJ12

In order to achieve a pH of 0.00, we need to add enough HCl to neutralize all of the NaOH and create a solution with an excess of H+ ions.

The balanced chemical equation for the reaction between HCl and NaOH is as HCl + NaOH → NaCl + H2O.

This equation shows that one mole of HCl reacts with one mole of NaOH to produce one mole of NaCl and one mole of water.

Since the initial solution contains 2.0 moles of NaOH per liter, we need to add 2.0 moles of HCl per liter to neutralize all of the NaOH.

Therefore, we need to add a total of 2.0 moles of HCl to 1.0 liter of 2.0 M NaOH to achieve a pH of 0.00.

Read more about the Moles.

https://brainly.com/question/15209553

#SPJ11

The correct option is D Not possible, because this process would violate only conservation of momentum.

To determine if the process obeys the conservation laws, we can analyze the initial and final states of the system. According to the conservation of momentum, the total momentum before and after the explosion must be equal.

Initially, the total momentum is 0 since the object is at rest. After the explosion, the total momentum can be calculated as follows:

Total momentum = (mass of fragment 1 × velocity of fragment 1) + (mass of fragment 2 × velocity of fragment 2) + (mass of fragment 3 × velocity of fragment 3)

Total momentum = (5M × -v) + (M × v) + (2M × 2v)

Total momentum = -5Mv + Mv + 4Mv

Total momentum = 0Mv

As the total momentum after the explosion is not equal to the initial total momentum (0), this process violates the conservation of momentum.

Learn more about momentum here:

https://brainly.com/question/22418297

#SPJ11

The sum can be expressed using the binomial theorem as:

[tex](1 + x)^n[/tex] = Σ(r=0 to n) nCr * [tex]x^r[/tex]

We can substitute x = [tex]x^9[/tex] to obtain:

[tex](1 + x^9)^n[/tex] = Σ(r=0 to n) nCr *[tex]x^9^r[/tex]

We can simplify the expression by recognizing that the sum on the right-hand side is identical to the sum we want to express in closed form, except that the variable is r instead of 9r. We can change the variable of summation by letting r' = 9r, which implies that r = r'/9. Then, we have:

Σ(r=0 to n) nCr * [tex]x^9^r[/tex] = Σ(r'=0 to 9n) nCr'/9 *[tex]x^r[/tex]'

We can see that the sum on the right-hand side is now expressed in terms of r' and can be written using the binomial theorem as:

[tex](1 + x)^9^n[/tex]= Σ(r'=0 to 9n) nCr' *[tex]x^r[/tex]'

Substituting back r' = 9r, we obtain the closed form expression:

[tex](1 + x^9)^n[/tex] = Σ(r=0 to n) nCr' * [tex]x^9^r[/tex]

Learn more about expression

brainly.com/question/28172855

#SPJ11