The calculations listed provide a comprehensive understanding of the thermodynamic performance of the Rankine cycle power plant and the water requirements of the plant.
This is a thermodynamics problem involving an ideal Rankine cycle power plant that uses water as its working fluid. The problem requires the calculation of various parameters, including the work done by the turbine, work consumed by the pump, heat input, heat rejected, efficiency, and mass flow rates of water and cooling water.
The problem also requires a comparison of the mass flow rate of cooling water to the residential water use of a person in the US. The solution to this problem involves applying the principles of thermodynamics, specifically the Rankine cycle, and using relevant equations to calculate the required parameters.
To know more about Rankine cycle power plant, here
brainly.com/question/29485182
#SPJ4
which of the following is the correct chemical formula for the final product after heating mnso4 h20
MnSO4•H2O is the correct chemical formula for the final product after heating MnSO4•H2O.
This compound is known as Manganese (II) sulfate monohydrate. When heated, the water of hydration is lost, leaving MnSO4 as the final product.Manganese (II) sulfate monohydrate is an inorganic compound composed of manganese(II) cations, sulfate anions, and one water molecule of hydration. It is a white crystalline solid with the formula MnSO4•H2O. It is used as an oxidizing agent, a fertilizer, and a micronutrient in agriculture. It may also be used to test for the presence of phosphate and carbonate ions.Manganese (II) sulfate monohydrate is a white crystalline solid that is used as a fertilizer and in the production of a variety of chemical products. It is made up of one manganese atom, four oxygen atoms, one sulfur atom, and four water molecules.
learn more about sulfate anions Refer:brainly.com/question/24245877
#SPJ4
Problem: 8.41 g magnesium oxide reacts with 5.40 L of carbon dioxide to form 14.45 g of a compound that is 28.83% magnesium, 14.24% carbon, and 56.93% oxygen. What is the percent yield?
The yield is 108.2% in percentage. As this result is higher than 100%, it is possible that the experimental process or the measurements had errors.
What occurs when carbon dioxide and magnesium oxide interact?In mild conditions, magnesium oxide works well as a catalyst for the cycloaddition of carbon dioxide to epoxides; when carbon dioxide reacts with (R)-styrene oxide in the presence of magnesium oxide, (R)-phenyl carbonate is produced in 97% of the time with stereochemistry retained.
We must first estimate the theoretical yield of the compound generated in order to calculate the percent yield.
molar mass of MgO = 24.31 g/mol (for Mg) + 15.99 g/mol (for O) = 40.30 g/mol
moles of MgO = 8.41 g / 40.30 g/mol = 0.2087 mol MgO
moles of compound formed = 0.2087 mol MgO = 0.2087 mol compound
mass of compound = (28.83% Mg / 100%) x 14.45 g = 4.16 g Mg
(14.24% C / 100%) x 14.45 g = 2.06 g C
(56.93% O / 100%) x 14.45 g = 8.23 g O
= 14.45 g of the compound formed
percent yield = (actual yield / theoretical yield) x 100%
actual yield = 14.45 g
theoretical yield = 0.2087 mol x (24.31 g/mol + 15.99 g/mol + 3(16.00 g/mol)) = 13.36 g
percent yield = (14.45 g / 13.36 g) x 100% = 108.2%.
To know more about magnesium visit:-
https://brainly.com/question/1533548
#SPJ1
write on nitrogen and state it uses and explain it process and draw a nitrogen cycle and explain it test
Nitrogen is a chemical element with the symbol N and atomic number 7. It is a nonmetal and makes up about 78% of the Earth's atmosphere. Nitrogen is essential for all forms of life on Earth as it is a critical component of DNA, RNA, and proteins.
Uses:
Nitrogen has many uses in industry, agriculture, and medicine. In the industrial sector, nitrogen is used in the production of ammonia, which is used to make fertilizers, explosives, and other chemicals. Nitrogen gas is also used to create a controlled atmosphere in food storage and packaging, to prevent spoilage and preserve freshness. In the medical field, nitrogen is used to preserve blood, tissues, and other biological samples.
Process:
Nitrogen gas is produced through a process called fractional distillation, which separates the gases in the air based on their boiling points. Nitrogen gas is obtained by cooling air until it becomes a liquid, and then slowly warming it up again. Nitrogen gas boils at a lower temperature than oxygen gas, so it is collected as a gas as the temperature rises.
Nitrogen Cycle:
The nitrogen cycle is the process by which nitrogen is converted between its various chemical forms in the environment. The nitrogen cycle is important because it allows nitrogen to be used by living organisms, and it helps to regulate the levels of nitrogen in the atmosphere and in the soil.
The nitrogen cycle consists of four main stages: nitrogen fixation, nitrification, denitrification, and ammonification. Nitrogen fixation is the process by which nitrogen gas from the atmosphere is converted into a form that can be used by living organisms, such as ammonia or nitrate. This process is carried out by certain types of bacteria that live in the soil or in the roots of plants.
Nitrification is the process by which ammonia is converted into nitrate by other types of bacteria. This nitrate can then be absorbed by plants and used to make proteins and other essential molecules.
Denitrification is the process by which nitrate is converted back into nitrogen gas, which is released back into the atmosphere. This process is carried out by certain types of bacteria that live in oxygen-poor environments, such as wetlands or soils that are waterlogged.
Ammonification is the process by which organic nitrogen compounds, such as proteins or amino acids, are broken down into ammonia by bacteria and fungi. This ammonia can then be used by other organisms in the nitrogen cycle.
Testing:
The most common test for the presence of nitrogen is the Kjeldahl method, which is used to determine the amount of nitrogen in organic compounds. The Kjeldahl method involves heating a sample of the organic compound with sulfuric acid, which converts the nitrogen into ammonia. The ammonia is then distilled off and collected in a solution of boric acid, which forms a compound called ammonium borate. The amount of nitrogen in the original sample can then be determined by measuring the amount of ammonium borate that is produced.
Please help I don't understand
According to the IUPAC nomenclature, there are 3 carbon atoms in longest chain, there is no functional group and name of compound is propane.
What is functional group?Functional group is defined as a substituent or group of toms or an atom which causes chemical reactions.Each functional group will react similarly regardless to the parent carbon chain to which it is attached.This helps in prediction of chemical reactions.
The reactivity of functional group can be enhanced by making modifications in the functional group .Atoms present in functional groups are linked to each other by means of covalent bonds.
Learn more about functional group,here:
https://brainly.com/question/14618322
#SPJ1
When a particular ionic solid begins to dissolve in water, the temperature rises dramatically. For the dissolution of this solid in pure water we can state that __O Lattice energy is larger than enthalpy of hydration in magnitudeO Enthalpy of solvation is positiveO Enthalpy of hydration is positiveO Enthalpy of solution is negativeO Enthalpy of solution is positive
The rise in temperature during the dissolution of an ionic solid in water is a result of the release of energy, indicating that the process is exothermic.
The enthalpy of solution is the difference between the energy required to separate the ionic solid into its constituent ions, known as the lattice energy, and the energy released during the hydration of these ions by water molecules. Since the dissolution of the solid is exothermic, the enthalpy of solution is negative. Therefore, we can state that the correct answer is "O Enthalpy of solution is negative" . Additionally, since the temperature rises dramatically during the dissolution of the ionic solid, it indicates that the magnitude of the lattice energy is greater than the enthalpy of hydration of the ions in water.
Find out more about enthalpy of solution
brainly.com/question/14529494
#SPJ4
covalent molecular crystals have very low melting points, while covalent network crystals have very high melting points because ______
covalent molecular crystals have very low melting points, while covalent network crystals have very high melting points because the forces in molecular crystals are weaker than the network crystals.
The intermolecular forces that hold the covalent molecules together in the molecular crystals are weaker than that of the intermolecular force that hold the molecules or the atoms together in the network crystals.
The Covalent network are contain the atoms that are covalently bonded together in the three dimensional network or the `layers of two dimensional networks. Because of the strength of the covalent bonds, the covalent network solids have the high melting points.
To learn more about melting points here
https://brainly.com/question/19282734
#SPJ4
The presence of dark lines at specific wavelengths in an otherwise continuous spectrum can be explained most easily by which of the following?
a. A cool gas between observer and source is absorbing light at the wavelengths corresponding to the missing photons.
b. The peak of the emission in the spectrum of the cooler object is at a longer wavelength.
The simplest straightforward explanation for the existence of black lines at particular wavelengths in an otherwise continuous spectrum is that a cool gas between observer and source is absorbing light at the wavelengths where the missing photons should be present.
What is meant by wavelength?The distance between two identical points (adjacent crests) in adjacent cycles of a waveform signal as it moves through space or along a wire is known as its wavelength. In wireless systems, this length is frequently specified in meters (m), centimeters (cm), or millimeters (mm) (mm).The distance between two wave crests determines the wavelength, whereas a wave's trough has a constant wavelength.The number of vibrations that pass over a specific place in a second is known as the frequency and is expressed in cycles per second (Hz) (Hertz). Here are some wavelength illustrations: Yellow Light, for instance. All visible light has a wavelength between 400 and 700 nanometers (nm). The wavelength of yellow light is approximately 570 nanometers. Wavelength (nm) (nm)To learn more about wavelength, refer to:
https://brainly.com/question/28995449
#SPJ4
The simplest straightforward explanation for the existence of dark lines at particular wavelengths in an otherwise continuous spectrum is that a cool gas between observer & source is absorbing light at the wavelengths where the missing photons should be present.
What is meant by wavelength?The wavelength of a waveform signal, as it travels through space or along a wire, is the separation between two identical points (adjacent crests) in adjacent cycles. This length is frequently stated in metres (m), centimetres (cm), or millimetres (mm) in wireless systems (mm).
The number of vibrations that pass over a specific place in a second is known as the frequency and is expressed in cycles per second (Hz) (Hertz). Here are some wavelength illustrations: Yellow Light, for instance.
All visible light has a wavelength between 400 and 700 nanometers (nm). The wavelength of yellow light is approximately 570 nanometers. Wavelength (nm) (nm)
To learn more about wavelength, refer to:
brainly.com/question/28995449
#SPJ4
which of the following would you expect to have the most negative (most exothermic) electron affinity?
a. Cl
b. Cl-
c. Cl +
a) Cl is the atom Atoms are expected to have the most negative (exothermic) electron affinities.
Electron AffinityElectron affinity is the amount of energy produced or released when an atom attracts an electron. Electron affinity can be used as a measure of the ease with which an atom captures electrons. The greater the energy released (electron affinity) indicates that the atom tends to attract electrons to become a negative ion.
Electron affinity can be used as a measure of the ease with which an atom captures electrons. The greater the energy released (electron affinity) indicates that the atom tends to attract electrons to become a negative ion.
About exothermicThe energy of an atom is defined when the atom loses or gains energy through a chemical reaction that causes the loss or gain of electrons. Chemical reactions that release energy are called exothermic reactions and chemical reactions that absorb energy are called endothermic reactions.
The energy of an exothermic reaction is negative, so the energy is given a negative sign; while the energy of the endothermic reaction is positive and the energy is given a positive sign. An example that demonstrates both processes is when someone drops a book. When he lifts the book, he gives the book potential energy (absorbed energy).
Learn more about electron affinity at
https://brainly.com/question/977718
#SPJ4
Please Help
Inorganic Chemistry
The Kp value, at 500 K for the reaction 2NO(g) + Cl2(g) ↔ 2NOCl(g) is Kp=0.01.
2NO(g) + Cl2(g) ↔ 2NOCl(g)
Coefficient of the reaction equation: 2 - 1 – 2
Several moles of gas at equilibrium:
moles of NO gas = 2 molesmoles of gas Cl2 = 1 molemoles of NOCl gas = 2 molesThe number of moles of gas = 5 moles
Calculate the partial pressure of NO gas.PNO = (mol NO/total moles) x Ptotal
PNO = (2/5) x 500
PNO = 200 K
Calculate the partial pressure of Cl gas.PCl = (mol Cl/mol total) x Ptotal
PCl = (1/5) x 500
PCl = 100 K
Calculate the partial pressure of NOCl gas.PNOCl = (mol NOCl/mol total) x Ptotal
PNOCl = (2/5) x 500
PNOCl = 200 K
Calculating the value of Kp:
Kp = (right side partial pressure)[tex]^{coefficient}[/tex]/(left side partial pressure)[tex]^{coefficient}[/tex]
Kp = [PNOCl]²/[PNO]²[Cl]
Kp = [200]²/[200]²[100]
Kp = 4 x 10⁴/4 x 10⁶
Kp = 0.01
Answer is Kp = 0.01
Learn more about the Kp value at https://brainly.com/question/15521600.
#SPJ1
(Urgent)
5 moles of glucose is dissolved in 10 liters of water , what is the concentration of the solution in molarity?
The concentration of the solution in molarity can be calculated as follows:
Molarity (M) = moles of solute/liters of solution
In this case, the number of moles of glucose is 5 moles and the volume of the solution is 10 liters. So,
M = 5 moles / 10 liters = 0.5 M
Therefore, the concentration of the glucose solution is 0.5 M.
The best name for H2S when it is classified as an acid is _____(i)_______; the best name for N2O when named as a molecular compound is _____(ii)_________; and the best name for Cs2O is ______(iii)_________.
O (i) hydrosulfuric acid; (ii) dinitrogen monoxide; (iii) cesium oxideO (i) dinitrogen monoxide; (ii) hydrosulfuric acid; (iii) cesium oxideO (i) dinitrogen monoxide; (ii) cesium oxide ; (iii) hydrosulfuric acidO (i) hydrosulfuric acid; (ii) cesium oxide ; (iii) dinitrogen monoxide
(i)hydrosulfuric acid; (ii) dinitrogen monoxide; (iii) cesium oxide are the correct answers.
What are compounds ?
Compounds are substances made up of two or more different types of atoms that are chemically bonded together in a specific ratio. The atoms in a compound are held together by chemical bonds, which are formed when the atoms share or transfer electrons in order to achieve a more stable electron configuration.
There are many different types of compounds, including covalent compounds, ionic compounds, and metallic compounds.Covalent compounds are formed when atoms share electrons in order to complete their valence electron shells. Ionic compounds are formed when electrons are transferred from one atom to another, resulting in the formation of positive and negative ions that are attracted to each other by electrostatic forces.
To learn more about the compounds, click the given link ;
https://brainly.com/question/26487468
#SPJ4
what is an electrolyte
Answer:
Electrolytes are a substance that breaks into ions when it is dissolved in water or body fluid.
Explanation:
Sodium, potassium, and chloride are your 3 main electrolytes. Magnesium, calcium, phosphate, and bicarbonates are also some types of electrolytes.
Could a floccing agent be designed for Nitrate? If so, what would you recommend?
Support your answer with an explanation of a few sentences. (2 pt)
It is absolutely true that floccing agent could be designed for Nitrate.
What is floccing agent?Chemical additives known as flocculating agents induce suspended particles to agglomerate into flocs.
These chemicals are used in papermaking, mineral processing, municipal and industrial waste treatment, and water treatment. Inorganic salts or water-soluble organic polymers are flocculating agents.
Floccing agents for nitrate can be created. Floccing agents are substances that make small liquid particles clump into larger particles so that they can be more easily removed from the liquid.
Each floccing agent should be thoroughly assessed for its suitability in a particular application.
Thus, the given statement is true.
For more details regarding floccing agent, visit:
https://brainly.com/question/13355012
#SPJ9
which of these two aqueous solutions has (a) the higher boiling point, (b) the higher freezing point, and (c) the lower vapor pressure: 0.35 m cacl2 or 0.90 m urea? (a) higher boiling point (b) higher freezing point (c) lower vapor pressure 0.35 m cacl2 0.90 m urea 0.35 m cacl2 0.90 m urea 0.35 m cacl2 0.90 m urea
The correct response is (a) Higher boiling point, (b) Higher freezing point, and (c) Lower vapor pressure, all of which are 0.35 M CaCl2.
What is boiling point point?Boiling point is the temperature where a pure substance transforms from the a liquid to a gas. Now, the pressure being applied to the liquid and its vapour are equal. Boiling at one pressure atmosphere is the standard boiling point. Boiling point and saturation temperature are synonyms. The standard boiling point was established by the International Union of Pure and Applied Chemistry (IUPAC) in 1982 as the temperature at which water boils at one bar of pressure.
What is boiling point vs evaporation?A temperature at which a liquid's vapor pressure equals the surrounding pressure is known as the boiling point. The boiling point falls off as altitude rises. Evaporation is the transformation of a liquid into its vapor when it occurs below the liquid's boiling point. As a result of the water molecules' vibrations caused by heat, some of the water's molecules escape into the atmosphere and turn into water vapor, or even the gaseous state for water. We name it evaporation for this reason. Water turns from a liquid to a gas known called vapor.
This is because urea does not dissociate, but CaCl2 breaks down into three ions in solution—one Ca2+ and two Cl-. CaCl2's higher boiling point, lower vapor pressure, and lower freezing point are all caused by the presence of more particles in the solution (since the solute ions disrupt the crystal lattice formation of the solvent molecules).
To know more about Boiling Point visit:
https://brainly.com/question/2153588
#SPJ4
if each dimer is 20 angstroms in length, calculate approximately how long (in feet or miles) a strand of nylon can be formed in this experiment. type out your calculations. (2 pts)
Approximately 1.24 × 10^-9 miles of nylon could be formed in this experiment, assuming 10,000 dimers are linked together.
One angstrom is equal to 1 × 10^-10 meters, and there are 3.281 feet in one meter, so:
20 angstroms × (1 × 10^-10 m/angstrom) × (3.281 ft/m) = 6.5628 × 10^-10 ft
Let's assume that in this experiment, 10,000 dimers are formed.
length = 6.5628 × 10^-10 ft/dimer × 10,000 dimers = 6.5628 × 10^-6 ft
This is the total length of nylon that could be formed in this experiment, assuming 10,000 dimers are linked together.
To convert this to miles, we can divide by the number of feet in a mile:
6.5628 × 10^-6 ft / 5,280 ft/mi = 1.240 × 10^-9 miles
To know more about the dimers, here
brainly.com/question/29517510
#SPJ4
What minerals are formed or dissolved in water according to the amount of carbonic acid present?
Water containing carbonic acid can react with minerals like calcite (CaCO₃) and dolomite (CaMg(CO₃)₂) to dissolve them, resulting in the formation of bicarbonate (HCO₃⁻) and calcium or magnesium ions in solution.
When carbonic acid is present in water, it can react with minerals such as calcite (CaCO₃) and dolomite (CaMg(CO₃)₂) to dissolve them, forming bicarbonate (HCO₃⁻) and calcium or magnesium ions in solution. This process is known as chemical weathering and can result in the formation of underground caves and sinkholes.
On the other hand, when the concentration of carbonic acid decreases, the reverse reaction can occur, and minerals such as calcium carbonate can precipitate out of solution, forming deposits such as stalactites and stalagmites in caves.
To know more about the carbonic acid, here
brainly.com/question/17584484
#SPJ4
which compound can lower the freezing temperature of water, similarly to the antifreeze used in automobiles, and allow certain fish to remain active in very cold water? please choose the correct answer from the following choices, and then select the submit answer button. answer choices acetylcholine
"antifreeze proteins" or "ice-binding proteins", lower the freezing temperature of water, similarly to the antifreeze used in automobiles, and allow certain fish to remain active in very cold water.
Antifreeze proteins function by binding to ice crystals and preventing them from growing, which in turn prevents the formation of ice within the tissues of the organism. This allows the organism to remain active in very cold water, even when the water temperature is below the freezing point of pure water.
Acetylcholine is not a compound that can lower the freezing temperature of water.It is important to note that antifreeze proteins are a specialized adaptation that has evolved in certain organisms to help them survive in extremely cold environments, and they should not be confused with the antifreeze used in automobiles, which is a mixture of chemicals designed to lower the freezing point of the liquid in a car's cooling system.
To know more about "antifreeze proteins" here
https://brainly.com/question/28546218
#SPJ4
which of the following in each pair is likely to be more soluble in water? cyclohexane (c6h12) or glucose (c6h12o6):
The one which is more likely to be more soluble in the water is the glucose.
The like dissolve the like. The glucose is the polar compound and the water is also the polar compound. The polar compound will dissolves the polar compound. Therefore , the glucose is dissolves in the water. The cyclohexane is not soluble in the water because the cyclohexane is the non polar compound and will be soluble in the non polar solvent. The cyclohexane will be more soluble in the hexane as the hexane is the non polar compound.
Thus, the glucose is more soluble in the water .
To learn more about glucose here
https://brainly.com/question/29678043
#SPJ4
If the total pressure of a mixture of O2 N2, and H2 is 902 mmHg, what is the pressure of O, if there pressure of N2 is 355 mmHg N2 and H, is 0.3 atm?
Considering the Dalton's partial pressure, the pressure of O₂ in the mixture is 319 mmHg.
Definition of Dalton's partial pressureDalton's law states that the total pressure of a gas mixture is equal to the sum of the partial pressures of the gas:
[tex]P_{T}[/tex]= P₁ + P₂ + ... + Pₙ
where:
n is the amount is the amount of gases present in the mixture.the partial pressure of each gas is the pressure that the gas would exert if it were the only gas in the container.This relationship is due to the assumption that there are no attractive forces between the gases.
Pressure of O₂In this case, you know:
Total pressure= 902 mmHgPressure of O₂= ?Pressure of N₂= 355 mmHgPressure of H₂= 0.3 atm= 228 mmHg (being 1 atm= 760 mmHg)If the total pressure of the mixture is:
Total pressure= Pressure of O₂ + Pressure of N₂ + Pressure of H₂
the pressure of O₂ can be calculated as:
902 mmHg= Pressure of O₂ + 355 mmHg + 228 mmHg
Solving:
902 mmHg= Pressure of O₂ + 355 mmHg + 228 mmHg
902 mmHg= Pressure of O₂ + 583 mmHg
902 mmHg - 583 mmHg= Pressure of O₂
319 mmHg= Pressure of O₂
Finally, the pressure of O₂ is 319 mmHg.
Learn more about Dalton's partial pressure:
brainly.com/question/14239096
#SPJ1
is the formula of both copper (1) superoxide and copper (2) peroxide CuO2?
No, The formula CuO2 is for copper super peroxide
The formula of copper peroxide is Cu2H2O2
ii. What did Niels Bohr's 1913 model of the atom look like? (2 points)
Niels Bohr's 1913 model depicts that the atom has a small, positively charged nucleus which surrounded by electrons that travel in circular orbits around the nucleus.
What is Bohr's model of an atom?The Bohr model, is a representation of the structure of atoms, especially that of hydrogen, The Bohr Model is a universal model in which the negatively charged electrons orbit a small, positively charged nucleus like the planets.
In the Bohr model, electrons are pictured as traveling in circles at dissimilar shells, depending on which element you have. The Bohr model is a proportional primitive model of the hydrogen atom, in contrast to the valence shell mode
So we can conclude that the Bohr Model is a structural model of an atom that shows electrons and the nucleus of an atom.
Learn more about Bohr Model here: https://brainly.com/question/4138548
#SPJ1
Chlorination of ethylbenzene in the para position proceeds by way of a carbocation intermediate that has three resonance structures. Complete one of these resonance structures by dragging bonds, electrons and charges to the appropriate locations. Then check your answer.
Sure! Here's the complete resonance structure of the carbocation intermediate formed during the chlorination of ethylbenzene in the para position Cl | H--C--C |+ C | C | H.
Cl
|
H--C--C
|+
C
|
C
|
H
In this structure, the positive charge is located on the carbon atom adjacent to the chlorine atom, indicating that this carbon is electron deficient and has a high degree of reactivity. This carbocation intermediate can then go on to react with a chlorine ion to form the final product, para-chloro ethylbenzene.
It's worth noting that the other two resonance structures of this carbocation intermediate involve moving the positive charge to the other two carbon atoms in the ring, but they are less stable due to increased electron density at the adjacent carbon atoms.
Learn more about ethylbenzene here:
https://brainly.com/question/16971326
#SPJ4
Explain the meaning of each term within the Arrhenius
equation: activation energy, frequency factor, and exponential
factor. Use these terms and the Arrhenius equation to explain
why small changes in temperature can result in large changes in
reaction rates.
Small changes in temperature can have a large effect on reaction rates because the exponential factor in the Arrhenius equation is very sensitive to changes in temperature.
The Arrhenius equation is a mathematical formula that describes the relationship between temperature and the rate of a chemical reaction. It is often written as: k = A × [tex]e^{-Ea/RT}[/tex]
The activation energy (Ea) is the minimum energy required for a reaction to occur. In other words, reactant molecules need to have at least this amount of energy in order to break the bonds that hold them together and form the new products. The activation energy can be thought of as the energy barrier that reactants must overcome to form products.
The frequency factor (A) is a constant that reflects the frequency of successful collisions between reactant molecules. A higher frequency factor means that more successful collisions are occurring, which generally leads to a faster reaction rate.
The exponential factor, [tex]e^{-Ea/RT}[/tex], is a mathematical term that describes how the rate constant changes with temperature. This term incorporates the activation energy and temperature in a way that reflects the probability that a given collision between reactant molecules will lead to a successful reaction. At higher temperatures, the exponential factor is larger, which means that the rate constant (k) is higher and the reaction proceeds more quickly.
To know more about Arrhenius equation here
https://brainly.com/question/30514582
#SPJ4
The rate law expresses the relationship of the rate of a reaction to the rate constant and the concentration of the reactants raised to some powers for the general reaction.
aA+bB→cC+dD
Rate law takes the form
r=k[A]x[B]y
where x and y are number that must be determined experimentely k is the rate constant and [A] and [B] are concentration of A & B respectively.
Gaseous reaction A→B+C
follows first order kinetics concentration of A changes from A changes from 1M to 0.25M in 138.6 min.Find the rate of reaction when conc. of A is 0.1 M.
The rate law is the relationship between the rate of a reaction and the rate constant, as well as the concentration of reactants raised to various powers.
What is rate law ?In chemical kinetics, the rate law (also known as the rate equation) is a mathematical equation that describes the rate of a chemical reaction as a function of the concentrations of the reactants. The rate law provides a quantitative way of expressing how the rate of a reaction depends on the concentration of each reactant, as well as any other factors that may affect the reaction rate, such as temperature or the presence of a catalyst. The general form of a rate law is:
rate = k[A]^m[B]^n
where "rate" is the rate of the reaction, [A] and [B] are the concentrations of the reactants A and B, respectively, and k is the rate constant. The exponents m and n are the reaction orders with respect to A and B, respectively, and they determine how the rate of the reaction changes with changes in the concentration of each reactant.
0.072 M/min is the correct answer.
r2 = 0.2/5
r1/r2= [A1/A2]m
K=1/25
r= K×1/8= 0.072 M/min
The between relationship the rate of a reaction and the rate constant, as well as the concentration of the reactants raised to various powers for the overall process, is expressed by the rate law.
To learn more about the rate law, click the given link ;
brainly.com/question/7694417
#SPJ4
Lab coats provide an additional layer of protection in the laboratory andhelp prevent insidious exposure to potential biological, chemical, and other contaminants. In choosing a basic lab coat, which of the following fabric is acceptable? O 100% cotton O 60% cotton, 40% polyester O 100% polyester O 60% polyester, 40% cotton
The choice of fabric for a lab coat will depend on the specific hazards present in the laboratory and the level of protection required for the lab workers. It is important to consult with safety guidelines and regulations to ensure that the lab coat selected meets the necessary safety standards. Select a fabric that will provide adequate protection.
Of the options listed, a 100% cotton lab coat would not be ideal for all laboratory settings as it can be easily penetrated by chemicals and biological agents. A 60% cotton, 40% polyester blend may offer some added protection due to the presence of polyester, but it still may not be sufficient for all lab environments.
A 100% polyester lab coat would offer better protection against chemical and biological exposure than the cotton options, but it may not be as comfortable to wear as cotton. A 60% polyester, 40% cotton blend may provide a balance of protection and comfort, but the level of protection provided may still depend on the specific type of fabric and construction of the lab coat.
Learn more about laboratory protection here: https://brainly.com/question/8363737
#SPJ4
PLEASE HELPPPPPPPPPP
The speed of light in kilometers per second is 300 kps.
What are the variables?According to the information on light speed from the Sun to the Earth:
Known:
Distance light travels in 10 seconds from Sun to Earth = 3,000,000 km
Average distance between Earth and Sun = 150,000,000 km
Formula:
Speed = Distance / Time
Unknown:
Speed of light in kps
Substitutions:
Distance = 3,000,000 km
Time = 10 seconds
Speed = Distance / Time
Speed = 3,000,000 km / 10 seconds
Speed = 300,000 km/s
Answer:
The speed of light in kps is 300 kps (kilometers per second).
Find out more on light speed here: https://brainly.com/question/104425
#SPJ1
it is blank to result in increase o2 delivery to muscles because a drop in co2 will blank the stability of the t state, which results in a blank p50 and blank o2 release from hemoglobin.
According to the Bohr effect, an increase in the supply of oxygen (O2) to muscles will result from a drop in carbon dioxide (CO2) levels.
The reason for this is that a decrease in CO2 weakens the T state of haemoglobin, which is the type of haemoglobin that binds oxygen. The P50 level (the partial pressure of oxygen at which haemoglobin is half-saturated with oxygen) decreases and the release of O2 from haemoglobin increases due to the T state's poorer stability. Enhanced O2 supply to muscles is the effect of this increased O2 release. The Bohr effect is a phenomena wherein when the pH of the immediate environment falls, hemoglobin's affinity for oxygen also diminishes.
learn more about Bohr effect Refer:brainly.com/question/15970643
#SPJ4
for each part below, determine which highlighted element forms a monatomic ion by losing electons from or adding electrons to the below-mentioned orbitals.
Losing s electron: None of the above, Losing 2 s electrons: Red, Losing 2 s and 1 p electron: Orange, Adding 1 p electron: Green and Adding electrons to 2 p orbitals: Blue.
Part 1: The correct answer would be (f) None of the above since not all elements form monatomic ions by losing an s electron. Some elements may require losing electrons from other orbitals or may not form monatomic ions at all.
Part 2: The correct answer would be (d) Red. Elements in Group 2A of the periodic table can lose two s electrons to form doubly positive ions, and the element highlighted in red belongs to this group.
Part 3: The correct answer would be (c) Orange. Elements in Group 3A of the periodic table can lose two s electrons and one p electron to form triply positive ions, and the element highlighted in orange belongs to this group.
Part 4: The correct answer would be (b) Green. Elements in Group 5A of the periodic table can add one electron to a p orbital to form singly negative ions, and the element highlighted in green belongs to this group.
Part 5: The correct answer would be (a) Blue. Elements in Group 6A of the periodic table can add electrons to two p orbitals to form doubly negative ions, and the element highlighted in blue belongs to this group.
Learn more about periodic table :
https://brainly.com/question/11155928
#SPJ4
The complete question is :
each part below, determine which highlighted element forms a monatomic ion by losing electons from or addling electrons to the below-mentione orbitals
Part(1) by losing an s electron: Choose one:
(a)Blue
(b) Green
(c) Orange
(d) Red
(e)Brown/Black
(f) None of the above
Part 2 (1 point) by losing two s electrons: Choose one:
(a)Blue
(b) Green
(c) Orange
(d) Red
(e)Brown/Black
(f) None of the above
Part 3 (1 point) by losing two s electrons and one p electron Choose one: (a)Blue
(b) Green
(c) Orange
(d) Red
(e)Brown/Black
(f) None of the above
Part 4 (1 point) by adding one electron to a p orbital Choose one:
(a)Blue
(b) Green
(c) Orange
(d) Red
(e)Brown/Black
(f) None of the above
Part 5 (1 point) by adding electrons to two p orbitals Choose one:
(a)Blue
(b) Green
(c) Orange
(d) Red
(e)Brown/Black
(f) None of the above
You have two containers at STP. Flask #1 contains F2 gas and flask #2 contains CO2 gas. What can you say
about the number of moles of molecules in each flask, and what can you say about the average speed of the
molecules in each flask? (In other words compare Flask #1 to Flask #2 - think about terms such as more, less,
same, faster, slower, etc)
If the volume of the gases in the container taken in STP is equal they they contains equal number of moles of the gas. As the volume increases, mobility of gases increases.
What is Avogadro's law ?Avogadro's law states that, at constant pressure and temperature, the volume of gas is directly proportional to the number of moles. If two gases at STP have equal volume, they contains equal number of moles.
The temperature of 298 K and 1 atm pressure is taken as standard condition (STP). At STP, the volume of one mole of every substance contains 22.4 L volume.
The carbon dioxide gas and fluorine gas if taken in equal volume at STP, they contain equal number of moles. Then, the average speed is inversely proportional to mass. Then , fluorine gas will have greater speed.
Find more on Avogadro's law:
https://brainly.com/question/3491421
#SPJ9
Which of the following samples contain the greatest number of molecules?
1.00 grams of carbon monoxide
1.00 grams of carbon dioxide
1.00 grams of carbonate
All samples listed above have the same number of molecules
The sample contain the greatest number of molecules is 1.00 grams of carbon dioxide. Therefore, option B is correct.
What do you mean by the molecule ?The term molecule is defined as the smallest component of a material that possesses both its chemical and physical characteristics. One or more atoms make up molecules.
There are three different kinds of molecules: atom-sized molecules, element-sized molecules, and compound-sized molecules.
1.00 grams of carbon monoxide,1.00 grams of carbon dioxide and 1.00 grams of carbonate, atoms present in these molecules are different so 1.00 grams of carbon dioxide contain the greatest number of molecules.
Thus, option B is correct.
To learn more about the molecule, follow the link;
https://brainly.com/question/19922822
#SPJ1