Answer: A step-down transformer changes the magnitude of the voltage in an alternating current (AC) electrical signal. It reduces the voltage of the AC signal by using a winding ratio between the primary (input) and secondary (output) coils that is less than 1:1.
Explanation: For example, if the winding ratio of a step-down transformer is 1:0.5, the output voltage of the secondary coil will be half the magnitude of the input voltage of the primary coil. In this case, the transformer would change the AC voltage from a higher value to a lower value.
The transformer does not change the frequency of the AC signal, which is determined by the source of the electrical power. The transformer also does not change the waveform of the AC signal, which is typically a sinusoidal wave.
if a player kicks a football from ground level with a velocity of 27/ms at an angle of 30 degrees above the horizontal then what is the initial horizantal velocity of the football?
The initial horizontal velocity of the football if a player kicks a football from ground level with a velocity of 27/ms at an angle of 30 degrees above the horizontal is 23.662 m/s.
To find the initial horizontal velocity (Vx) of the football, you can use the horizontal component of the velocity vector. The horizontal component of velocity is found by multiplying the velocity by the cosine of the angle of launch.
[tex]V_{x}[/tex] = V × cos(angle)
where V is the initial velocity, the angle is the angle of launch (in this case, 30 degrees), and cos is the cosine function.
So, in this case, the initial horizontal velocity of the football would be:
[tex]V_{x}[/tex] = 27 m/s × cos(30)
[tex]V_{x}[/tex] = 27 m/s × 0.866
[tex]V_{x}[/tex] = 23.662 m/s
So the initial horizontal velocity of the football, which moves in the x-direction, is approximately 23.662 m/s.
This means the football will move 23.662 m/s in x direction initially and if no air resistance acts upon the football, it will move at the same velocity in x direction throughout the motion.
Learn more about velocity :
https://brainly.com/question/28738284
Exercise 24.28
For the capacitor network shown in (Figure 1), the potential difference across ab is 48 V.
Part A
Find the total charge stored in this network.
Express your answer with the appropriate units.
Q = ___ ____
Part B
Find the charge on the 150nF capacitor.
Express your answer with the appropriate units.
Q₁ = 7.2uC
Part C
Find the charge on the120nF capacitor.
Express your answer with the appropriate units.
Q₂ = 5.76 uC
Part D
Find the total energy stored in the network.
Express your answer with the appropriate units.
U = ____ ____
Part E
Find the energy stored in the 150nF capacitor.
Express your answer with the appropriate units.
U₁ = ______
Part F
Find the energy stored in the 120nF capacitor.
Express your answer with the appropriate units.
U₂= _____
Part G
Find the potential difference across the 150nF capacitor.
Express your answer with the appropriate units.
V₁= ____
Part H
Find the potential difference across the 150nF capacitor.
Express your answer with the appropriate units.
V₂ = ____
The evaluation of the capacitor (in series) network is as follows;
Part A
Q = 3.2 μC
Part B
Q₁ = 3.2 μC
Part C
Q₂ = 3.2 μC
Part D
U = 76.8 μJ
Part E
U₁ = 34 2/15 μJ
Part F
U₂ = 53 1/3 μJ
Part G
V₁ = 21 1/3 V
Part H
V₂ = 26 2/3 V
What is a capacitor?A capacitor consists of pairs of conductors separated by insulators. Capacitors are used to store electric charge.
The specified parameters are;
The voltage across ab = 48 V
The capacitance of the first capacitor, C₁ = 150 nF
Capacitance of the second capacitor, C₂ = 120 nF
Part A
The total charge in a capacitor network can be found as follows;
[tex]C_{eq} = \left(\dfrac{1}{150} + \dfrac{1}{120} \right)^{-1} nF = \left(\dfrac{3}{200} \right)^{-1}nF[/tex]
[tex]C_{eq} =\left(\dfrac{3}{200} \right)^{-1}nF=66\frac{2}{3} \, nF[/tex]
[tex]Q_{eq} = C_{eq}\times V_{ab}[/tex]
Therefore;
[tex]Q_{eq}[/tex] = 66 2/3 nF × 48 V = 3,200 × 10⁻⁹ C = 3.2 μC
The total charge in the circuit is 3.2 μCPart B
The charge in the 150 nF capacitor is obtained from the formula for the charge in a capacitor; Q = C × V as follows;
Q = C₁V₁ = C₂V₂
The charge in the capacitors, C₁ and C₂ are the same as the total charge of 3.2 μC
The charge, Q₁ on the 150 nF capacitor, C₁ is therefore, 3.2 nC
Q₁ = 3.2 nCPart C
The capacitors, C₁ and C₂ are in series, therefore, the charge in each capacitor is equivalent to the charge in the circuit, which is 3.2 μC.
Therefore, the charge, Q₂, in the 120 nF capacitor, C₂ is 3.2 μC
Q₂ = 3.2 μF
Part D
The total energy stored in the network can be obtained using the formula;
U = (1/2)·C·V²
Where;
U = The energy in the capacitor
C = The equivalent capacitance of the network = 66 2/3 nF
V = The voltage
Therefore;
[tex]U = \dfrac{1}{2} \times C_{eq}\times V^2[/tex]
[tex]U = \dfrac{1}{2} \times 66\frac{2}{3} \times 10^{-9}\times 48^2 = 76.8[/tex]
The total energy in the circuit, U = 76.8 μJPart E
The energy stored in the 150 nF capacitor is found as follows;
[tex]Q_{eq}[/tex] = Q₁ = C₁ × V₁
V₁ = [tex]Q_{eq}[/tex] ÷ C₁
Therefore;
V₁ = 3.2 μC ÷ 150 nF = [tex]21\frac{1}{3}[/tex] V
U₁ = 0.5×C₁×V₁²
U₁ = 0.5 × 150×10⁻⁹ × [tex]\left(21\frac{1}{3} \right)^2[/tex] = 34[tex]\frac{2}{15}[/tex] μJPart F
The energy stored in the 120 nF capacitor, U₂, can be found as follows;
V₂ = 3.2 μC ÷ 120 nF = [tex]26\frac{2}{3}[/tex] V
U₂ = 0.5 × 150 nF × [tex]\left(26\frac{2}{3} \, V\right)^2[/tex] = [tex]53\frac{1}{3}\, \mathrm{ \mu J}[/tex]
The energy in the 120 nF capacitor is; U₂ = 53 1/3 μJPart G;
The potential difference across the 150 nF, obtained in Part E, is 21 1/3 V
V₁ = 21 1/3 VPart H
The potential difference across the 120 nF, obtained in part F, is 26 2/3 V
V₂ = 26 2/3 VLearn more about capacitors networks here: https://brainly.com/question/9525710
#SPJ1
H
Question 12 of 15:
Select the best answer for the question.
12. A 150-lb block of ice has a temperature of 22 F. How much heat will the ice absorb before it begins to melt?
O A. 1500.0 Btu
O B. 1663.2 Btu
C. 756.0 Btu
OD. 2419.2 Btu
Answer:
I think it is A
Explanation:
It is A because if you calculate the weight minus the F, then you have to divide that by the amount of absorbation (the lb) before timsing it by 1000.
A box is pushed with a 245 N of force on a horizontal surface as it moves with a
constant velocity. The mass of the box is 104 kg. The box experiences a force of friction
of 45 N.
a. Draw a free body diagram with Fg, FN, F₂ and F₁.
b. Find the weight of the box.
c. Find the coefficient of friction as the box is moving.
d. Find the net force acting the box.
Answer:
Explanation:
b) Fg = W = mg = (104 kg)(9.8 m/s²) = 1019.2 N (weight of the box)
Ff = (coeff. friction)(N)
N = normal force = Fg = 1019.2 N
c) coeff. friction = Ff/N = 45 N/1019.2 N = 0.044
d) Fnet = 245 N - 45 N = 200 N
It's hard to draw a free body diagram with the available symbols, but here's a try at it. Just add a box between the arrows!
W
↓
Ff → ← Fapplied
↑
N
What are the horizontal and vertical components of a cat's displacement when the cat has climbed 5 m
directly up a tree © = 90°? Sin90=1
cos90=0
The horizontal component of the cat's displacement, Dx = 0 m
The vertical component of the cat's displacement, Dy = 12 m
What are the horizontal and vertical components of a vector?The horizontal component of a vector is the value of that vector acting in the horizontal direction.
The horizontal component of a vector is given as Dx.
Dx = Dcosθ
where;
D is the resultant of the vector
θ is the angle of the vector from the horizontal
The horizontal component of the cat's displacement is:
Dx = 12 * 0
Dx = 0 m
The vertical component of a vector is the value of that vector acting in the vertical direction.
The vertical component of a vector is given as Dy.
Dy = Dsinθ
where;
D is the resultant of the vector
θ is the angle of the vector from the horizontal
The vertical component of the cat's displacement is:
Dy = 12 * 1
Dy = 12 m
Learn more about horizontal and vertical components at: https://brainly.com/question/26446720
#SPJ1
Calculate the potential energy of a rock of mass 500 g, held at a height of 2 m above ground.
The potential energy of a rock of mass 500 g, held at a height of 2 m above ground is 9.8J.
The formula for the gravitational potential energy of an object is:
PE = mgh
where m is the mass of the object, g is the acceleration due to gravity (approximately 9.8 m/s^2 on the Earth's surface), and h is the height of the object above the reference point.
So, in this case, we can plug in the given values to find the potential energy of the rock:
PE = (500 g) x (9.8 m/s^2) x (2 m)
The weight of the rock is m*g = 500 g * 9.8 m/s^2 = 4.9 N
Therefore,
PE = 4.9 N x 2 m = 9.8 J
Therefore, the potential energy of a rock of mass 500 g, held at a height of 2 m above ground is 9.8J.
Learn more about Energy:
https://brainly.com/question/29979940
What are the names and number of of atoms in a molecule of nitrous oxide,N2O?
Answer:
2 nitrogen and 1 oxygen,
Explanation:
N2=2 nitrogen
O= a single element
What will be the change in temperature if 600 g of water absorbs 5200 J of heat?
The change in temperature of the 600 g of water, given that the water aborbs 5200 J of heat energy is 2.07 °C
How do I determine the change in temperature of the water?First, we shall list out the given parameters from the question. This is given below:
Mass of water (M) = 600 gHeat absorbed (Q) = 5200 JChange in temperature (ΔT) = ?Calorimetry suggest the following formula:
Q = MCΔT
Where
Q is the heat transferred M is the mass C is the specific heat capacity ΔT is the change in temperatureUsing the above formula, the change in temperature of the water can be obtained as follow:
Note: Specific heat capacity of water (C) = 4.184 J/gºC
Q = MCΔT
5200 = 600 × 4.184 × ΔT
5200 = 2510.4 × ΔT
Divide both sides by 2510.4
ΔT = 5200 / 2510.4
ΔT = 2.07 °C
Thus, we can conclude from the above calculation, that the change in temperature of the water is 2.07 °C
Learn more about temperature change:
https://brainly.com/question/17107322
#SPJ1
A graph of v(t) is shown for a world-class track sprinter in a 100 -m race. (See figure below. For each answer, enter a number.)
(a) What is his average velocity (in m / s ) for the first 4 s} ?
______ m/ s
(b) What is his instantaneous velocity (in m / s ) at t=6 s ?
______ m / s
(c) What is his average acceleration (in m / s²) between 0 and 4s?
________m / s²
(d) What is his time (in s) for the race?
______ s
a) The average velocity at 4s is 12 m/s
b) The instantaneous velocity at t= 6s is 12 m/s
c) The average acceleration is; 12 - 0/ 4 - 0 n= 3 m/s^2
d) The time for the race is 10 s
What is the velocity time graph?We know that the velocity time graph is the kind of set up that has two axis and we can be able to use it to be read off the velocity of the acceleration of the object. I would want us to recall that the acceleration is the rate of change of the velocity of the object with time.
Now we have that;
The graph for the velocity of the object can be obtained by looking at the image that has been shown and then we read off the points that are on the graph. The vertical axis shows the velocity of the graph while the horizontal axis shows the time that is covered in the graph.
The acceleration would be the ratio of the change in the velocity to the change in the time of the object.
Learn more about velocity time graph:https://brainly.com/question/28357012
#SPJ1
Robert Galstyan, from Armenia, pulled two coupled railway wagons a distance of 7 m using his teeth. The total mass of the wagons was about 2.20 X 10^5 kg. Of course, his job was made easier by the fact that the wheels were free to roll. Suppose the wheels are blocked and the coefficient of static friction between the rails and the sliding wheels is 0.220. What would be the magnitude of the minimum force needed to move the wagons from rest? Assume that the track is horizontal.
The magnitude of the minimum force needed to move the wagons from rest is 474320 N
How do I determine the force needed to move the wagons?We have come to know that the force and coefficient of friction have a simple relationship as shown by the equation below:
Frictional force (N) = coefficient of friction (μ) × normal reaction (N)
F = μN
Applying the above formula, we can determine the force needed to move the wagons from rest. Details below:
Mass of wagons (m) = 2.20×10⁵ KgAcceleration due to gravity (g) = 9.8 m/s²Normal reaction (N) = mg = 2.20×10⁵ × 9.8 = 2156000 NCoefficient of static friction (μ) = 0.220Force needed (F) = ?F = μN
F = 0.220 × 2156000
F = 474320 N
Thus, the force needed is 474320 N
Learn more about force:
https://brainly.com/question/12163222
#SPJ1
Synthetic pesticides and fertilizers were used extensively during the Green Revolution, but the negative health and environmental impacts were not well-known since the effects added up over time.
True
False
(True) Synthetic pesticides and fertilizers were used extensively during the Green Revolution, but the negative health and environmental impacts were not well-known since the effects added up over time.
what are Synthetic pesticidesChemicals created by humans, synthetic pesticides are meant to kill or deter pests. They are mostly utilized in agriculture, although they are also employed in other fields of endeavor and in household settings. In the 1930s, synthetic pesticides were first used in the United States of America (USA).
Chemicals known as synthetic pesticides are employed to manage and control plant pests like weeds, insects, and/or fungal infections.
Danger synthetic pesticidesHuman health problems associated with exposure to synthetic pesticides include
increased rates of cancer, birth defects and fertility problems.learn more about Synthetic pesticides here
https://brainly.com/question/28997034
#SPJ1
The Astronomical Unit (AU) as defined by astronomers is
Answer:
a unit of length effectively equal to the average, or mean, distance between Earth and the Sun
Explanation:
Question
Stopping Distance
48.0 ft
49.0 ft
50.0 ft
51.0 ft
52.0 ft
2
The stopping distance for 10 cars traveling at 55 miles per hour is shown in the table above. What is the
mean (average) stopping distance for the 10 cars?
Frequency
1
2
3
2
Two students push on a box in the same direction, and one student pushes in the opposite direction. What is the net force on the
box if each student pushes with a force of 50 N?
Net force on the box is 50 N if 2 students push it in the same direction with 50 N of force each and one student pushes it in the other direction with 50 N of force.
Define force.An object with mass experiences a pull or push, which changes its velocity. An agent with the ability to change a body's rest or moving condition is known as an external force. It has both magnitude as well as direction.
The force formula according to Newton is what?F = ma, meaning force is equal to the mass times acceleration, is the second of Newton's three laws of motion.
To know more about force visit :
https://brainly.com/question/13191643
#SPJ1
• Calculate the magnetic field strength inside a solenoid with a radius of 2m and has 2000 loops. Furthermore, it carries a 1600 A current?
The magnetic field strength of the solenoid of radius 2 m is 2.0096 T.
What is a magnetic field?Magnetic field is the region or space around which magnetic force is felt or experienced.
To calculate the magnetic field strength inside a solenoid, we use the formula below.
Formula:
B = μni/r......................... Equation 1Where:
μ = permeability of free spacen = Number of loopsr = Radius of the solenoidB = Magnetic field strengthi = CurrentFrom the question,
Given:
μ = 4π×10⁻⁷T.m/Ai = 1600 An = 2000 loopsr = 2 mSubstitute these values into equation 1
B = (4π×10⁻⁷×1600×2000/2)B = 2.0096 THence, the magnetic field strength is 2.0096 T.
Learn more about magnetic field here: https://brainly.com/question/26257705
#SPJ1
A 3.00kg mass is attached to an ideal spring with k=200N\m if the velocity of body at 0.25m Is 2.3m\s find the amplitude and maximum velocity
To solve this we must be knowing each and every concept related to velocity. Therefore, the amplitude and maximum velocity are 0.23 m and 2.75 m/s respectively.
What is velocity?V is the velocity measurement of an object's rate of motion and direction of motion. As a result, in order to calculate velocity using this definition, we must be familiar with both magnitude and direction.
For example, if an item travels west with 5 meters a second (m/s), its velocity to the west will be 5 m/s. The most frequent and simplest approach to determine velocity is using the formula shown below.
v = √(k / m) ×A
v = velocity of the mass
k= spring constant
m =mass of the object
A= amplitude of the oscillation.
substituting all the given values in the above equation, we get
2.3 m/s = √(200 N/m / 3.00 kg)×A
A = 2.3 m/s / √(200 N/m / 3.00 kg)
= 0.23 m
v =√(200 N/m / 3.00 kg) ×0.23 m
= 2.75 m/s
Therefore, the amplitude and maximum velocity are 0.23 m and 2.75 m/s respectively.
To learn more about velocity, here:
https://brainly.com/question/13372043
#SPJ1
Your friend Christy has always been good at making schedules-she plans her days out to the minute and
loves helping others be more productive in this way too. Which career in astronomy might she be suited for?
Ground Control
CAPCOM
Flight Controller
Flight Director
She might be best suited for a profession as an astronomy flight controller. The target speed for every one of the 4 motors is determined by the flight controller using the information acquired by the sensors.
Why study astronomy?The goal of astronomy is to explain whatever we see within the universe, including the planets and comets inside our own solar system, far-off galaxies, and echoes of something like the Big Bang.
Is math required for astronomy?Math is constantly used by astronomers. When using a telescope to see celestial objects, one application of it is this. The camera that is mounted on the telescope essentially captures a series of numbers, which could represent the amount of light that various celestial objects emit.
To know more about astronomy visit:
https://brainly.com/question/286348
#SPJ1
A single movable pulley is used to lift 4000N load to the height of 50 cm. If the efficiency of the pulley is 75%, Calculate effort distance,effort applied,output work and mechanical advantage.
Since the efficiency of the pulley is 75% and the single movable pulley is used to lift 4000N load to the height of 50 cm, the effort distance, effort applied, output work and mechanical advantage are as follows:
Effort Distance = 50 cm
Effort Applied = 5333.33 N
Output work = 2000 J
Mechanical Advantage = 0.75.
When a single movable pulley is used to lift a load, the effort applied is equal to the weight of the load being lifted, and the effort distance is the distance the effort is applied.
Load (output force) = 4000 N
Height lifted = 50 cm = 0.5 m
Efficiency of the pulley = 75%
Given the above information, we can calculate the effort applied, output work, and mechanical advantage as follows:
Effort applied (input force) = Load ÷ Efficiency
= 4000 N ÷ 0.75
= 5333.33 N
Output work = Load x Height lifted
= 4000 N x 0.5 m
= 2000 J
Effort distance = Height lifted
= 50 cm
Mechanical advantage = Load ÷ Effort applied
= 4000 N ÷ 5333.33 N
= 0.75
It is worth noting that pulley efficiency is the ratio of output work to the input work. And since the efficiency of the pulley is 75% so the input work is greater than the output work, which means some of the energy is wasted in overcoming friction and other losses.
Learn more about pulley:
https://brainly.com/question/25855047
A horse pulls a wagon with a force of 1450 Newtons. How many meters sis the wagon travel if the horse exerted 798 watts of power over 3.5 minutes? (convert min. to seconds).
The distance traveled by the horse pulling the wagon with a force of 1450N is 115.57 metres.
How to calculate power?Power is defined as the amount of energy used or transferred in a certain amount of time. This means that power can be calculated by dividing the work done by the time taken.
P = W/t
When a force is applied to move an object, work is done on the object. Work done = force × distance
Power = (Force × distance)/time
According to this question, a horse pulls a wagon with a force of 1450 Newtons.
798 = 1450 × d/210
167,580 = 1450d
Distance = 167,580 ÷ 1450
Distance = 115.57 metres
Therefore, 115.57 metres is the distance traveled by the wagon.
Learn more about power at: https://brainly.com/question/3854047
#SPJ1
Hi, can anyone help me with this question I have?
Assume a tornado is in the vicinity of your neighborhood. Which would
be the most useful information to determine your safety - speed or
velocity? Explain your answer.
Answer:
speed
Explanation:
you need to move fast so the tornado can't reach you
Taylor has set this fitness goal: I will go to the YMCA and lift weights for 30 minutes every other day for the entire month of January. What is MOST likely TRUE about this goal?
Since Taylor has set this fitness goal: I will go to the YMCA and lift weights for 30 minutes every other day for the entire month of January. The option that MOST likely TRUE about this goal is option A:It is a short-term goal.
What is the fitness goal about?A short-term goal is a goal that can be achieved within a relatively short period of time, usually less than a year. In this case, the goal is to go to the YMCA and lift weights for 30 minutes every other day for the entire month of January.
In this case, Taylor's goal is to go to the YMCA and lift weights for 30 minutes every other day for the entire month of January. This goal is specific, as it clearly states what Taylor wants to accomplish, and it is measurable.
This goal can be achieved within the month of January and it's a specific, measurable and time-bound goal, which are characteristics of short-term goals.
Learn more about fitness goal from
https://brainly.com/question/5247727
#SPJ1
See full question below
Taylor has set this fitness goal: I will go to the YMCA and lift weights for 30 minutes every other day for the entire month of January. What is MOST likely TRUE about this goal?
It is a short-term goal.
It is a long-term goal.
It is an unrealistic goal.
It is a mental health goal.
Answer:it’s a short-term goal
Explanation:
because it’s only for the month of January she will be doing this goal.
draw diagram of how a reflecting telescope works. show how the angles of reflection would work with mirrors placed at 2 different angles
Lenses, which are pieces of curved, clear glass, were employed in early telescopes to focus light.
What is Telescope?Curved mirrors are used by the majority of telescopes nowadays to collect light from the night sky. Light is focused by a telescope's mirror or lens' shape.
Astronomers use a telescope to observe distant things. Curved mirrors are used by the majority of telescopes, including all large telescopes, to collect and concentrate light from the night sky.
The original telescopes employed lenses, which are simply curved pieces of clear glass, to focus light. The "optics" of a telescope are the mirrors or lenses. Strong telescopes may view objects that are extremely faint and incredibly far away.
Therefore, Lenses, which are pieces of curved, clear glass, were employed in early telescopes to focus light.
To learn more about Telescope, refer to the link:
https://brainly.com/question/556195
#SPJ1
Ball A with a mass of 0.280kg makes an elastic head-on collision with ball B initially at rest. After collision, ball B moves off with half the original speed of ball A. Is the momentum conserved in the collision? Why?
The mass of ball B and the final velocity of ball A can complement the conservation of linear momentum. The answer is yes.
What is Momentum ?Momentum can simply be defined as the product of mass and velocity. It is a vector quantity.
Given that ball A with a mass of 0.280kg makes an elastic head-on collision with ball B initially at rest. After collision, ball B moves off with half the original speed of ball A.
In an elastic head-on collision, momentum is mostly always conserved. That is, the sum of the momentum before collision will be equal to the sum of the momentum after collision.
Mathematically, MaUa = MaVa + MbVb
Is the momentum conserved in the collision?
The answer is yes!
Why?
Because we need to consider the mass of the ball B and the final velocity of the ball A.
Therefore, In consideration of the mass of the ball B and the final velocity of the ball A, we can say that the momentum is conserved.
Learn more about Momentum here: https://brainly.com/question/25121535
#SPJ1
a three tiered birthday cake rests on a table. From the bottom to the top, the cake tiers weigh 15 N, 8N, and 6N, respectively. What is the magnitude and direction of the normal force acting on the base of the seconf tier
The normal force on the second tier of the cake is 14N. It is the sum of the weight of the last and the second tier of the cake.
What is Normal force?The normal force is the force which the surfaces exert to prevent solid objects from passing through each other. Normal force is a contact force. If two objects or surfaces are not in contact, they cannot exert a normal force on each other.
Fₙ = mg
Fₙ = Normal force
Fₙ on the second tier is the sum of the first and second tier of the cake is:
Fₙ = 8N + 6N
Fₙ = 14N
The normal force on the second tier is 14N.
Learn more about Normal force here:
https://brainly.com/question/18799790
#SPJ1
What are the magnitude and direction of the current in the 20 Ω resistor in (Figure 1)?
Express your answer with the appropriate units. Enter positive value if the current is clockwise and negative value if the current is counterclockwise.
To solve this we must be knowing each and every concept related to net current. Therefore, the circuit's overall net current is 0.1 A, flowing clockwise.
What is the net current?The term "net current" refers to the total currents after taking current direction into account. If a node sends 1 mA inside and 5 mA out, the total current equals 4 mA out.
The sum of all entering currents must match the sum of all exiting currents, according to KCL. According to Ohm's Law, the current flowing is equivalent to the combined voltage dividing by the entire resistance. In contrast to a series circuit, where the total current is the same across all of the components, the total current inside a parallel connection is really only equal to the particular current in that part of the circuit.
Net current
i = V / Ri
= (9 - 6) / (10 + 20)i
= 0.1 A
in clockwise way
Therefore, the circuit's overall net current is 0.1 A, flowing clockwise.
To know more about net current, here:
brainly.com/question/28326769
#SPJ1
Which of the following best illustrates an application of the principles of behaviorism?
A therapist is helping a client explore feelings about past events.
O A parent is using "time out" as a consequence for bad behavior.
O A friend is listening intently and showing concern for another.
O A mechanic is developing a mental map of the engines she routinely fixes.
The statement that best illustrates the application of the principles of behaviorism is -
"A parent is using "time out" as a consequence for bad behavior".
What is behaviorism?The theory that human and animal behaviour can be explained in terms of conditioning, without appeal to thoughts or feelings, and that some mental conditions are best treated by altering behaviour patterns.
Given are the applications of the principles of behaviorism.
The statement that best illustrates the application of the principles of behaviorism is -
"A parent is using "time out" as a consequence for bad behavior".
Therefore, the statement that best illustrates the application of the principles of behaviorism is -
"A parent is using "time out" as a consequence for bad behavior".
To solve more questions on behaviorism , visit the link below-
https://brainly.com/question/17101346
#SPJ1
A Ferris wheel, rotating initially at an angular speed of 0.16 rad/s, accelerates over a 8.0-s interval at a rate of 0.040 rad/s2. What is its angular speed after this 8.0-s interval?
Answer:
0.48 rad/s
Explanation:
We can use this equation to find the final velocity
[tex]w_f=w_0+at[/tex]
We are given
[tex]w_0=0.16[/tex]
[tex]t=8.0[/tex]
[tex]a=0.04[/tex]
Inserting those numbers into our equation gives us
[tex]w_f=0.16+0.04*8[/tex]
Lets solve for [tex]w_f[/tex].
[tex]w_f=0.16+0.32[/tex]
[tex]w_f=0.48[/tex]
Six vectors (a through f ) have the magnitudes and directions indicated in the figure. (Figure 1)
1.Rank the vector combinations on the basis of their magnitude.
Rank from largest to smallest. To rank items as equivalent, overlap them.
a+c
f+c
d
a+b
a+e
a+d
2.Rank the vector combinations on the basis of their angle, measured counterclockwise from the positivexaxis. Vectors parallel to the positivexaxis have an angle of0^\circ. All angle measures fall between0^\circand360^\circ.
Rank from largest to smallest. To rank items as equivalent, overlap them.
a+d
f+c
a+b
a+e
a+c
d
1. The rank of the vector combinations on the basis of their magnitude
a+b = a +d > a+c > f +c = d > a + e.
2. The rank of the vector combinations on the basis of their magnitude
a+d = a +b > a+c > f +c =d > a+e.
What is vector quantity?Any physical quantity having both magnitude and direction is called vector quantity.
According to figure:
a = 2 unit b = 2 unit c = 1 unit d = 2 unit e = 1 unit and f = √5 unit.
a + c = 2+1 unit = 3 unit
a + b = 2√2 unit
a + e = 2 -1 = 1 unit
a +d = 2√2 unit
f+ c = 2 unit
a+d = 2√2 unit
f+c = 2 unit
a+b = 2√2 unit
a+e = 1 unit
a+c = 3 unit
Hence, rank of the vector combinations on the basis of their magnitude
a+b = a +d > a+c > f +c = d > a + e.
Learn more about vector here:
https://brainly.com/question/29740341
#SPJ1
The position-versus-time plot of a boat positioning itself next to a dock is shown in the figure (Figure 1).
Rank the six points indicated in the plot order of increasing value of the velocity v, starting with the most negative. Rank the points in order of increasing value of the velocity. To rank items as equivalent, overlap them.
Incorrect: Try Again; 2 attempts remaining: no points deducted
The points in order of increasing value of the velocity can be ranked as:
B < C < A ≡ F < E < D.
What is velocity?The rate at which a body's displacement changes in relation to time is known as its velocity. Velocity is a vector quantity with both magnitude and direction. SI unit of velocity is meter/second.
According to the figure:
The points in order of increasing value of the velocity can be written as:
B < C < A ≡ F < E < D.
As the displacement becomes from positive to negative near point B, it has the lowest velocity and as the displacement becomes from negative to positive near point D, it has the highest velocity
Learn more about velocity here:
https://brainly.com/question/18084516
#SPJ1
Heat Transfer 12 Directions: Drag the arrows to the correct locations on the image. directions in which heat flows. The diagram below shows three solid objects. Two of the objects are hot and one is cold. If heat is transferred between these objects via conduction, use the arrows to indicate the direction.
That's the question and please someone help me I can't figure this out because of how much I've been absent throughout this lesson
If heat is transferred between these objects via conduction, both arrows will point towards the cold.
Heat energy is transferred through the mechanism of conduction when nearby atoms or molecules collide. In solids and liquids, where particles are more closely spaced, conduction happens more easily than in gases, where particles are more widely spaced. Heat transfers through solid materials via conduction. The roof, walls, and windows of your house all carry heat on hot days.
The act of heating a skillet on a stovetop is a typical illustration of conduction. The surface of the pan receives heat directly from the burner. The amount of kinetic energy that the particles in a sample of matter have converted to heat is measured by temperature. Conduction mostly comes in two flavors. Steady-state conduction is what they are. temporary conduction.
To learn more about Conduction from given link
https://brainly.com/question/12136944
#SPJ1