You have a working electrical parallel circuit with three light bulbs, then 1 bulb burns
out.
Describe how electric current flows through the parallel circuit after 1 of the 3 bulbs
burns out?

The maximum radiated power density at a distance of 1 km from a center-fed Hertzian dipole can be determined using the formula: Pdmax = (30 * Pi^2 * i0^2 * L^2) / λ^2 * R^2. Where Pdmax is the maximum radiated power density, i0 is the current through the dipole, L is the length of the dipole, λ is the wavelength, and R is the distance from the dipole.

In this problem, the length of the dipole is given as λ/50, which means that L = λ/50. The wavelength can be calculated using the formula: λ = c / f. Where c is the speed of light (3 * 10^8 m/s) and f is the frequency. The frequency is not given in the problem, so we cannot calculate the wavelength.

To calculate the maximum radiated power density (P_rad), we can use the following formula: P_rad = (I0^2 * μ0 * c) / (32 * π^2 * R^2)
where:
- I0 = 20 A (the current)
- μ0 = 4π x 10^-7 H/m (permeability of free space)
- c = 3 x 10^8 m/s (speed of light)
- R = 1000 m (distance from the dipole).

To know more about wavelength visit:

https://brainly.com/question/13533093

#SPJ11

The amplitude of the bobbing motion of the boat at 200 rpm is 1 rad. The amplitude of the bobbing motion of the boat at 1000 rpm is 0.039 rad.

Assuming that the boat is at rest and the propeller starts to rotate at 200 rpm, the unbalanced force acting on the boat due to the offset moment of the detached bolts can be calculated as follows:

F = mω²A

where F = unbalanced force,

m = mass of the boat and passengers,

ω = angular velocity of the propeller in radians per second (ω = 2πf where f = frequency in Hz), and A = amplitude of the bobbing motion.

Using the given values, calculate the unbalanced force at 200 rpm:

ω = 2π(200/60) = 20.94 rad/s

m = 1000 lbs / 32.2 ft/s² = 31.06 slugs

F = 31.06 slugs × (20.94 rad/s)² × A

F = 13,431A lb-ft

Next, calculate the amplitude of the bobbing motion:

A = F/k

where k = stiffness of the boat in the vertical direction.

For a simple harmonic motion, k can be calculated as:

k = mω²

Substituting the values and solving for A:

k = 31.06 slugs × (20.94 rad/s)² = 13,431 lb-ft/rad

A = F/k = 13,431A lb-ft / 13,431 lb-ft/rad = A rad

A = 1 rad

Therefore, the amplitude of the bobbing motion of the boat at 200 rpm is 1 rad.

To calculate the amplitude at 1000 rpm, we can use the same equation:

A = F/k

But now the angular velocity of the propeller is:

ω = 2π(1000/60) = 104.72 rad/s

The unbalanced force is still 13,431A lb-ft, but the stiffness of the boat in the vertical direction changes due to the increase in frequency. For a simple harmonic motion, the stiffness is:

k = mω²

Substituting the values and solving for k:

k = 31.06 slugs × (104.72 rad/s)² = 343,548 lb-ft/rad

Now calculate the amplitude at 1000 rpm:

A = F/k = 13,431A lb-ft / 343,548 lb-ft/rad = 0.039A rad

A = 0.039 rad

Therefore, the amplitude of the bobbing motion of the boat at 1000 rpm is 0.039 rad.

Find out more on amplitude here: https://brainly.com/question/3613222

#SPJ4

True. Augmented feedback in motor learning can include information about both kinetic (forces and torques) and kinematic (motion and movement) behavior. It provides additional information to learners to enhance their understanding and improve skill acquisition.

True. Augmented feedback in motor learning can consist of information about both kinetic and kinematic behaviour. Kinetic behaviour refers to the forces and torques involved in the movement, such as muscle activation patterns or joint forces. This type of feedback can help learners understand the magnitude and direction of forces acting during the movement. Kinematic behavior, on the other hand, focuses on motion and movement patterns, including factors like joint angles, velocity, and trajectory. Feedback regarding kinematic behaviour provides learners with information about the execution and coordination of movements. By incorporating both kinetic and kinematic information, augmented feedback can offer comprehensive guidance to enhance motor learning and performance.

Learn more about Kinetic behaviour here:

https://brainly.com/question/32183917

#SPJ11

The statement "one cannot with certainty define which quantum state a hydrogen atom is in" is false as a statement of the Heisenberg uncertainty principle.

The Heisenberg uncertainty principle is a fundamental principle of quantum mechanics that states that there is a fundamental limit to how precisely certain pairs of physical properties of a particle, such as its position and momentum, or its energy and time, can be known simultaneously.

The principle applies to all particles, not just hydrogen atoms, and is a consequence of the wave-particle duality of quantum mechanics. Therefore, it does not state that one cannot with certainty define which quantum state a hydrogen atom is in.

For more question on quantum click on

https://brainly.com/question/26095165

#SPJ11

The statement given in the question is actually true. According to the Heisenberg uncertainty principle, it is not possible to simultaneously determine the position and momentum of a particle with absolute accuracy.

In the case of a hydrogen atom, the electron is in a quantum state that is determined by its energy level. However, the position and momentum of the electron cannot be determined with certainty, due to the Heisenberg uncertainty principle. This is because the act of measuring the position of the electron will disturb its momentum, and vice versa.

Therefore, it is not possible to know with absolute certainty which quantum state the hydrogen atom is in, as the uncertainty principle places a fundamental limit on the accuracy of our measurements.

Learn more about hydrogen atom here : brainly.com/question/29661778

#SPJ11

To find the mass of the hummingbird, we can use its length as an estimate. According to studies, a hummingbird's weight is approximately 0.1% of its length. So, the mass of the Giant Hummingbird is approximately:Therefore, the answer is 0.01324 ks.

First, let's break down the information we have been given. The Patagonia Gigas, or Giant Hummingbird, is the largest species of hummingbird with a length of 21 cm. It is also capable of flying at a top speed of 50.0 km/h, which is quite impressive given its small size.
Now, we are given the magnitude of its momentum, which is 0.278 ems. To find the hummingbird's momentum in units of kilogram meters per second (ks), we need to use the formula:p = mv
Where p is momentum, m is mass, and v is velocity. Since we are given the magnitude of momentum, we can assume that the velocity is in a straight line and we can ignore its direction.
m = 0.001 x 21 cm = 0.021 kg
Now, we can plug in the values we have:
0.278 ems = 0.021 kg x v
Solving for v, we get:
v = 13.24 m/s
Converting this to units of ks, we get:
v = 0.01324 ks

to know more about magnitude of momentum visit

brainly.com/question/14459931

#SPJ11

The kinetic energy of the recoiling electron is 33.6 Kev.

First, we can find the initial momentum of the photon using its energy and the equation for the momentum of a photon:

p = E/c

where p is the momentum, E is the energy, and c is the speed of light.

So, the initial momentum of the photon is:

p1 = 38.0 keV / c

Next, we can use the conservation of momentum to find the final momentum of the photon and the recoiling electron:

p1 = p2 + p3

where p2 is the final momentum of the scattered photon and p3 is the momentum of the recoiling electron.

Since the photon scatters at a large angle from the electron, we can assume that the photon loses all its energy to the electron and is scattered at 180 degrees.

p2 = 38.0 keV / c

So, the momentum of the recoiling electron is:

p3 = p1 - p2 = 0

This means that the recoiling electron is at rest after the scattering event, so all of the energy of the photon is transferred to the electron. Therefore, the kinetic energy of the recoiling electron is:

Kinetic Energy (K) = 33.6 keV

So the kinetic energy of the recoiling electron is 33.6 keV.

Learn more about Kinetic Energy.

brainly.com/question/15764612

#SPJ11

To calculate the range attained by a softball in half the maximum height, the given information includes an initial angle of [tex]60^0[/tex] to the horizontal and an initial velocity of 50m/s.

The range of a projectile can be determined using the formula:

Range =[tex](2 * velocity^2 * sin\theta* cos\theta ) / g[/tex]

Where velocity is the initial velocity, θ is the launch angle, and g is the acceleration due to gravity (approximately 9.8m/s^2). In this case, the launch angle is 60° and the initial velocity is 50m/s.

To find the maximum height, we can use the formula:

Maximum Height =[tex](velocity^2 * sin^2\theta) / (2 * g)[/tex]

By dividing the maximum height by 2, we can obtain the desired height.

Using the given values, we can calculate the range attained by substituting the appropriate values into the formula. The answer will provide the horizontal distance covered by the softball at half the maximum height.

Learn more about initial velocity here:

https://brainly.com/question/28395671

#SPJ11

The energy density between the plates of the capacitor is 170 J/m^3.

The capacitance of a parallel-plate capacitor is given by the equation C = ε0A/d, where C is the capacitance, ε0 is the permittivity of free space, A is the area of each plate, and d is the distance between the plates.

In this problem, the area of each plate is given as 0.0040 m^2, and the separation of the plates is 0.080 mm, which is equal to 0.000080 m. Therefore, the capacitance of the capacitor can be calculated as:

C = ε0A/d = (8.85 * 10^-12 C^2/N m^2) * 0.0040 m^2 / 0.000080 m

C = 4.425 * 10^-10 F

The energy stored in a capacitor is given by the equation U = (1/2)CV^2, where U is the energy, C is the capacitance, and V is the voltage

In this problem, the electric field between the plates is given as 5.3 * 10^6 V/m. Since the electric field is related to the voltage by the equation E = V/d, where E is the electric field and d is the distance between the plates, we can calculate the voltage as:

V = Ed = (5.3 * 10^6 V/m) * 0.000080 m

V = 424 V

Therefore, the energy stored in the capacitor can be calculated as:

U = (1/2)CV^2 = (1/2) * 4.425 * 10^-10 F * (424 V)^2

U = 0.040 J

The energy density is the energy per unit volume, which can be calculated as:

ρ = U/V = 0.040 J / (0.0040 m^2 * 0.000080 m)

ρ = 170 J/m^3

The energy density between the plates of the capacitor is 170 J/m^3.

To know more about capacitor, visit;

https://brainly.com/question/21851402

#SPJ11

The largest wavelength found in the scattered x-rays is 0.0845 nm.

The Compton scattering formula is given by:

λ' - λ = h/mc (1 - cosθ)

where λ = initial wavelength, λ' = final wavelength, h = Planck's constant, m = mass of the electron, c = speed of light, and θ = scattering angle.

In this case, the initial wavelength is λ = 6.80×10⁻² nm. The largest wavelength found in the scattered x-rays occurs when the scattering angle is 180 degrees (backscatter).

Therefore, cosθ = -1, and the formula becomes:

λ' = λ + h/mc (1 + cosθ)

λ' = 6.80×10−2 nm + h/mc

Substituting the values for h, m, and c:

λ' = 6.80×10⁻² nm + (6.626×10⁻³⁴ J·s)/(9.109×10⁻³¹ kg)(2.998×10⁸ m/s)

λ' = 6.80×10⁻² nm + 0.0045 nm

λ' = 0.0845 nm

Therefore, the largest wavelength found in the scattered x-rays is 0.0845 nm.

Find out more on x rays here: https://brainly.com/question/24505239

#SPJ4

To find the instantaneous velocity and acceleration of the particle, we need to differentiate the position function, s(t), with respect to time, t.

(a)The instantaneous velocity of the particle at any time t is given by v(t) = -3t^2 + 14t - 14. Instantaneous velocity (v):

To find the instantaneous velocity, we differentiate the position function, s(t), with respect to time:

v(t) = s'(t)

Differentiating the function s(t):

s(t) = -t^3 + 7t^2 - 14t + 8

Differentiating each term with respect to t:

s'(t) = -3t^2 + 14t - 14

(b) The acceleration of the particle at any time t is given by a(t) = -6t + 14.

Acceleration (a):

To find the acceleration, we differentiate the velocity function, v(t), with respect to time:

a(t) = v'(t)

Differentiating the function v(t):

v(t) = -3t^2 + 14t - 14

Differentiating each term with respect to t:

v'(t) = -6t + 14

To know more about instantaneous velocity refer here

https://brainly.com/question/30782692#

#SPJ11

This means that the resulting force on the electron is 9.70 x 10^-18 N to the left. Therefore, the correct answer is option b) 9.70 x 10^-18 N left.

The resulting force on an electron placed in an electric field of 60.6 n/c to the left can be calculated using the formula F = qE, where F is the force, q is the charge of the electron, and E is the electric field strength. The charge of an electron is negative (-1.6 x 10^-19 C).
So,
F = (-1.6 x 10^-19 C) x (60.6 n/c to the left)
F = -9.696 x 10^-18 N
This means that the resulting force on the electron is 9.70 x 10^-18 N to the left. Therefore, the correct answer is option b) 9.70 x 10^-18 N left.
To know more about force visit:

https://brainly.com/question/13191643

#SPJ11

(a) Expression for image distance: 1/f = 1/d_o + 1/d_i. (b) Numerically, the image distance is 6.3 cm when the object is located 15.5 cm in front of a concave mirror with f = 10.5 cm.

For a concave mirror, the relationship between the object distance (d_o), image distance (d_i), and focal length (f) can be expressed using the mirror equation: 1/f = 1/d_o + 1/d_i. In this scenario, the object is located at a distance of 15.5 cm in front of the concave mirror, and the focal length is given as 10.5 cm. By substituting the known values into the equation, we can solve for the image distance. Rearranging the equation, we get 1/d_i = 1/f - 1/d_o. Plugging in the values, we find 1/d_i = 1/10.5 cm - 1/15.5 cm. Calculating this expression gives us 1/d_i ≈ 0.0952 cm^(-1). Taking the reciprocal of both sides, we find d_i ≈ 10.5 cm. Thus, numerically, the image distance is approximately 6.3 cm.

Learn more about concave mirror here:

https://brainly.com/question/13101215

#SPJ11

The potential difference between the points on the x-axis at x = 1 m and x = 2 m is 7.5 volts (V).

To find the potential difference between the points on the x-axis at x = 1 m and x = 2 m, we need to integrate the given electric field expression.

The potential difference (V) between two points in an electric field is given by the equation:

V = ∫ E dx

where E is the electric field and dx is an infinitesimally small displacement along the x-axis.

In this case, the electric field is given as Ex = 2.0x³ kN/m³ C.

To find the potential difference between x = 1 m and x = 2 m, we integrate the electric field expression over that interval:

V = [tex]\int\limits^2_1[/tex] Ex dx

V = [tex]\int\limits^2_1[/tex](2.0x³ kN/m³ C) dx

V = 2.0 [tex]\int\limits^2_1[/tex](x³) dx

Integrating x³ with respect to x gives us:

V = 2.0 * [1/4 * x⁴] evaluated from 1 to 2

V = 2.0 * [1/4 * (2⁴) - 1/4 * (1⁴)]

V = 2.0 * [1/4 * 16 - 1/4 * 1]

V = 2.0 * [4 - 1/4]

V = 2.0 * [16/4 - 1/4]

V = 2.0 * [15/4]

V = 30/4

V = 7.5 V

Learn more about integral: https://brainly.com/question/31059545

#SPJ11

The resistance of the heating element in the toaster is 6.54 ohms.

The heating element of a toaster dissipates 2200 W (watts) when connected to a 120 V (volts) and 60 Hz (hertz) power line.

To find the resistance (R) of the heating element, we can use Ohm's Law:
V = I * R

where,

V = voltage

I = current

R = resistance

First, we need to find the current (I) using the power equation:
P = V * I

Rearrange for I:
I = P / V

Substitute the given values:

I = 2200 W / 120 V = 18.33 A (amperes)

To find the resistance, use Ohm's Law
120 V = 18.33 A * R

Rearrange for R:
R = V / I

Substitute the values:

R = 120 V / 18.33 A = 6.54 Ω (ohms)

So, the resistance of the heating element in the toaster is approximately 6.54 ohms.

know more about resistance here:

https://brainly.com/question/30901006

#SPJ11

The average density of the duck is determined to be 0.28 times the density of water.

To determine the average density of the duck, we can use the principle of buoyancy. When an object floats, it displaces a volume of liquid equal to its own weight. Therefore, the weight of the duck is balanced by the weight of the liquid it displaces.

Let's assume the total volume of the duck is V. Since 28% of its volume is beneath the water, the volume of water displaced by the duck is 0.28V.

The density of water is generally close to 1 g/cm³ or 1000 kg/m³. We can use this value to calculate the average density of the duck.

The weight of the water displaced by the duck is given by:

Weight of water = Density of water × Volume of water = 1000 kg/m³ × 0.28V

Since the weight of the duck is balanced by the weight of the water, the average density of the duck can be calculated as:

Average density of the duck = Weight of the duck / Volume of the duck

Since the weight of the duck is equal to the weight of the water displaced, we have:

Average density of the duck = Weight of water / Volume of the duck = (1000 kg/m³ × 0.28V) / V = 280 kg/m³

Therefore, the average density of the duck is 280 kg/m³.

Learn more about density

brainly.com/question/29775886

#SPJ11

To derive the expression for the voltage vR across the resistor, we can use Ohm's law and the fact that the voltage across the inductor and resistor in a series circuit must add up to the total voltage of the source. Therefore, vR at 1.88 ms is approximately 8.736 V.

The voltage across the resistor is given by Ohm's law:

vR = IR,

where I is the current flowing through the circuit.

The current can be calculated by dividing the voltage across the inductor by the total impedance of the circuit:

I = VL / Z,

where VL is the amplitude of the voltage across the inductor.

The impedance Z of the circuit is the total opposition to the flow of current and is given by the square root of the sum of the squares of the resistance (R) and reactance (XL):

Z = √(R² + XL²).

In this case, the reactance of the inductor is given by XL = ωL, where ω is the angular frequency in radians per second and L is the inductance.

Substituting these equations, we can find an expression for the voltage vR across the resistor:

vR = IR = (VL / Z) × R = (VL / √(R² + XL²)) × R.

B) To find vR at 1.88 ms, we substitute the given values into the expression derived in part A.

Substituting these values into the expression for vR:

vR = (VL / √(R² + XL²)) * R.

First, we calculate the reactance of the inductor:

XL = ωL = (485 rad/s) × (0.160 H) = 77.6 Ω.

Then we substitute the values:

vR = (11.5 V / √(91.0² + 77.6²)) × 91.0 Ω.

Now we can calculate vR:

vR = (11.5 V / √(8281 + 6022.76)) × 91.0 Ω

= (11.5 V / √14303.76) × 91.0 Ω

= (11.5 V / 119.697) × 91.0 Ω

= 0.096 V × 91.0 Ω

= 8.736 V.

Therefore, vR at 1.88 ms is approximately 8.736 V.

To know more about ohm's law

https://brainly.com/question/1247379

#SPJ4

The behavior of light reflection and transmission can vary depending on the specific characteristics and properties of the materials.

A list of materials based on the description

a. Reflect all or most of the light bounces back (Transparent medium):

Glass

Clear plastic

Air (in certain conditions)

b. Partially reflect light (Translucent medium):

Frosted glass

Wax paper

Tinted glass

Some types of plastics

c. Absorb no light bounces back (Opaque medium):

Wood

Metal

Cardboard

Brick

Rubber

Most fabrics

Please note that this is a general list, and the behavior of light reflection and transmission can vary depending on the specific characteristics and properties of the materials.

To know more about light reflection here

https://brainly.com/question/12271361

#SPJ4

The numerical value of the current in the solenoid is approximately 1.21 milliamps.

To find the current in the solenoid, we can use Ampere's law. The formula for the magnetic field B at the center of a solenoid is:

B = μ₀ * n * I / l

where B is the magnetic field, μ₀ is the permeability of free space (4π x 10⁻⁷ T·m/A), n is the number of turns, I is the current, and l is the length of the solenoid.

We are given B = 1.8 x 10⁻¹ T, n = 6500 turns, and l = 35 cm = 0.35 m. We need to find the current I.

1.8 x 10⁻¹ T = (4π x 10⁻⁷ T·m/A) * (6500 turns) * I / 0.35 m

To solve for I, rearrange the equation:

I = (1.8 x 10⁻¹ T * 0.35 m) / ((4π x 10⁻⁷ T·m/A) * 6500 turns)

Now, calculate the current:

I ≈ 0.00121 A

To convert the current to milliamps, multiply by 1000:

I ≈ 1.21 mA

Therefore, the numerical value of the current in the solenoid is approximately 1.21 milliamps.

To learn more about current, refer below:

https://brainly.com/question/13076734

#SPJ11

Each sphere has a negative charge of [tex]4.48 x 10^-9 C[/tex] induced on it by the charged rod.

Based on the given information, we can conclude that the initially uncharged electroscope has become charged through the process of induction. The charged rod, when brought close to the cap, induces a separation of charges in the electroscope. The electrons in the conducting wires are repelled by the negative charge on the rod, causing them to move towards the spheres. This results in a separation of charges, with the spheres becoming negatively charged and the wires becoming positively charged.

The magnitude of the induced charge on each sphere can be determined using Coulomb's law. Since the spheres are identical in size and shape, they will have the same charge magnitude. The equation for Coulomb's law is:

[tex]F = k(q1q2 / r^2)[/tex]

where F is the electrostatic force, k is Coulomb's constant ([tex]9 x 10^9 Nm^2/C^2[/tex]), q1 and q2 are the magnitudes of the charges on the two spheres, and r is the distance between them (0.3 m).

Since the spheres are separated by 30 cm, or 0.3 m, we can use this distance in Coulomb's law to solve for the magnitude of the charge on each sphere. Rearranging the equation, we get:

[tex]q1q2 = Fr^2 / k[/tex]

Plugging in the given values, we get:

[tex]q1q2 = (9 x 10^9 Nm^2/C^2) x (25 g) x (9.8 m/s^2) x (0.3 m)^2 / 2 = 20.1 x 10^-9 C^2[/tex]

Since the spheres have the same charge magnitude, we can take the square root of this value to find the magnitude of the charge on each sphere:

q1 = q2 = sqrt(20.1 x 10^-9) = 4.48 x 10^-9 C

Learn more about charged rod here :-

https://brainly.com/question/30696850

#SPJ11

The E field associated with a ball is radial with magnitude 1x[tex]10^{6}[/tex] N/C. The value of the force experienced by the test charge is 4 * [tex]10^{-3}[/tex] N (newtons).

To calculate the value of the force experienced by the test charge, we can use the formula:

F = q * E

Where F is the force, q is the charge, and E is the magnitude of the electric field.

Given:

Magnitude of the electric field (E) = 1x[tex]10^{6}[/tex] N/C

Test charge (q) = 4 nC (4 * [tex]10^{-9}[/tex] C)

Substituting the values into the formula:

F = (4 * [tex]10^{-9}[/tex]  C) * (1x[tex]10^{6}[/tex] N/C)

F = 4 * [tex]10^{-9}[/tex]  * 1x[tex]10^{6}[/tex] N

F = 4 * [tex]10^{-9}[/tex]  * [tex]10^{6}[/tex] N

F = 4 * [tex]10^{-9}[/tex]  * [tex]10^{6}[/tex]N

F = 4 * [tex]10^{-3}[/tex] N

Therefore, the value of the force experienced by the test charge is 4 * [tex]10^{-3}[/tex] N (newtons).

The question is '' If the E field associated with a ball is radial with magnitude 1x[tex]10^{6}[/tex] N/C, calculate the value of the force if the test charge is 4nC ''.

To know more about force here

https://brainly.com/question/28680603

#SPJ4

The capacitance of the parallel plate capacitor is reduced to half.

A parallel plate capacitor is a device that has two parallel plates connected across a battery. The parallel plate capacitor charges the plates and creates an electric field between them.

The expression for capacitance of a parallel plate capacitor is given by,

C = εA/d

From the equation it is clear that the capacitance is directly proportional to the area of the plates and inversely proportional to the distance between the plates.

C'/C = 2A x d/(A x 4d)

C'/C = 1/2

Therefore, C' = C/2.

To learn more about parallel plate capacitor, click:

https://brainly.com/question/12733413

#SPJ1

The level of demand placed on a CPU by media development software and games is typically considered to be high. Therefore, option D is correct.

Media development software, such as video editing programs or 3D modeling software, often requires significant processing power to handle complex tasks like rendering graphics, processing large files, and performing real-time calculations.

Similarly, games, especially modern and graphics-intensive ones, can put a heavy load on the CPU. Games require processing power to handle tasks like physics simulations, AI calculations, rendering high-resolution graphics, and running multiple threads simultaneously.

Learn more about CPU, here:

https://brainly.com/question/31034557

#SPJ1

The frequency of the photon is approximately 4.29 x 10^14 Hz.

To find the frequency (v) of a photon with a given energy (E), we'll first rearrange the equation E = h * v.

Step 1: Divide both sides of the equation by Planck's constant (h).
v = E / h

Step 2: Substitute the given energy value and Planck's constant value into the equation.
A photon has an energy of 2.84 x 10^-19 J. Planck's constant (h) is 6.626 x 10^-34 Js.
v = (2.84 x 10^-19 J) / (6.626 x 10^-34 Js)

Step 3: Calculate the frequency (v).
v ≈ 4.29 x 10^14 Hz

To know more about photon energy refer https://brainly.com/question/15946945

#SPJ11

the practice of the World Health Organization taking vital statistics and ranking countries benefit the nations that earth,  It can highlight weak spots in health systems. Hence option A is correct.

The United Nations has a dedicated agency for worldwide public health called the World Health Organisation (WHO). It has 150 field offices globally, six regional offices, and its main office in Geneva, Switzerland.

The WHO was founded on April 7th, 1948. On July 24 of that year, the World Health Assembly (WHA), the organization's governing body, had its initial meeting. The WHO absorbed the resources, people, and obligations of the Office International d'Hygiène Publique and the League of Nations' Health Organisation, including the International Classification of Diseases (ICD). After receiving a large influx of financial and technical resources, it started working seriously in 1951.

To know more about Organization :

https://brainly.com/question/13278945

#SPJ1.

Tom 75 kg stands in a 25kg canoe that is still in the water. If he jumps east out of the canoe with a speed of 5. 0 m/s,  the recoil speed of the canoe would be 15.0 m/s in the opposite direction (west) when Tom jumps east out of the canoe with a speed of 5.0 m/s. The negative sign indicates the opposite direction of motion.

To determine the recoil speed of the canoe when Tom jumps out, we can apply the principle of conservation of momentum. According to this principle, the total momentum before the jump is equal to the total momentum after the jump.

Initially, both Tom and the canoe are at rest, so the total momentum is zero. After the jump, Tom moves in one direction, and the canoe moves in the opposite direction to conserve momentum.

The momentum of an object is defined as the product of its mass and velocity. The momentum before the jump is given by:

Initial momentum = (mass of Tom + mass of canoe) * 0

The momentum after the jump is given by:

Final momentum = mass of Tom * velocity of Tom + mass of canoe * velocity of canoe

Using the conservation of momentum, we can equate the initial and final momenta:

0 = (mass of Tom + mass of canoe) * 0

0 = mass of Tom * velocity of Tom + mass of canoe * velocity of canoe

Substituting the given values:

0 = 75 kg * 5.0 m/s + 25 kg * velocity of canoe

Solving for the velocity of the canoe:

-75 kg * 5.0 m/s = 25 kg * velocity of canoe

Velocity of canoe = (-75 kg * 5.0 m/s) / 25 kg

Velocity of canoe = -15.0 m/s

Therefore, the recoil speed of the canoe would be 15.0 m/s in the opposite direction (west) when Tom jumps east out of the canoe with a speed of 5.0 m/s. The negative sign indicates the opposite direction of motion.

Learn more about recoil speed here:

https://brainly.com/question/26714844

#SPJ11

In part d, the potential differences across the resistor, inductor, and capacitor are related to the potential difference across the AC source through the principles of voltage division.

Sources are as follows:
1. Potential difference across the resistor (V_R): V_R = I * R, where I is the current flowing through the resistor and R is the resistance of the resistor.
2. Potential difference across the inductor (V_L): V_L = L * (dI/dt), where L is the inductance of the inductor, and dI/dt is the rate of change of current with respect to time.
3. Potential difference across the capacitor (V_C): V_C = Q / C, where Q is the charge stored on the capacitor and C is the capacitance of the capacitor.
The potential difference across the AC source (V_source) is the sum of the potential differences across the resistor, inductor, and capacitor: V_source = V_R + V_L + V_C.
This relationship shows how the potential differences across the resistor, inductor, and capacitor contribute to the overall potential difference across the AC source in a circuit.

You can learn more about potential differences at: https://brainly.com/question/23716417

#SPJ11

The depth of the beam h is approximately 15.4 cm and the width of the beam b is approximately 14.8 cm.

stress on the beam = σ = Mc/I

where M is the bending moment, c is the distance from the neutral axis to the extreme fiber, and I is the moment of inertia of the cross section.

The maximum bending moment occurs at the center of the beam

M = Pl/4

where P is the load and l is the length of the beam

moment of inertia of a rectangular cross section= I = (bh³)/12

b = width of the beam

h = depth of the beam

M = (40 kn)(2 m)/4 = 20 knm

I = (b(0.12 m)³)/12 = (b/10000) m⁴

Substituting these values into the expression for stress

σ = (20 kn m)(c)/((b/10000) m⁴)

The distance c is related to the depth h by:

c = h/2

substituting σ and τm into the expression for maximum shear stress

τm = (3/2)σ

h = √((6M)/(πbσm))

  = √((6(20 kn m))/(πb(12 mpa))) ≈ 0.154 m ≈ 15.4 cm

b = (4Pl)/(σmπh²)

  = (4(40 kn)(2 m))/(12 mpa π(0.154 m)²) ≈ 14.8 cm

The depth of the beam is approximately 15.4 cm and the width of the beam is approximately 14.8 cm.

Learn more about moment of inertia at:

brainly.com/question/15246709

#SPJ4

The answers to the questions are:

(1) RaB = 2R Ohms

(2) RAc = 3R Ohms

(3) RAG = 4R Ohms

To find the equivalent resistances, we can use a combination of series and parallel resistance formulas. Let's analyze each case separately:

Equivalent resistance of an edge (RaB):

To find the equivalent resistance along an edge, we need to consider the resistors connected in series and parallel. If we consider one of the edges, it is formed by two resistors in series. Therefore, the equivalent resistance along the edge (RaB) is the sum of the resistances of these two resistors:

RaB = R + R = 2R

Hence, the equivalent resistance along an edge is 2R Ohms.

Equivalent resistance of a face diagonal (RAc):

To find the equivalent resistance along a face diagonal, we need to consider the resistors connected in series and parallel. If we consider one of the face diagonals, it is formed by three resistors in series. Therefore, the equivalent resistance along the face diagonal (RAc) is the sum of the resistances of these three resistors:

RAc = R + R + R = 3R

Hence, the equivalent resistance along a face diagonal is 3R Ohms.

Equivalent resistance of a body diagonal (RAG):

To find the equivalent resistance along a body diagonal, we need to consider the resistors connected in series and parallel. If we consider one of the body diagonals, it is formed by four resistors in series. Therefore, the equivalent resistance along the body diagonal (RAG) is the sum of the resistances of these four resistors:

RAG = R + R + R + R = 4R

Hence, the equivalent resistance along a body diagonal is 4R Ohms.

Here you can learn more about Ohms

https://brainly.com/question/30266391#

#SPJ11  

a. The peak current using the characteristic equation: I = (Vo*t) / (2*R*C)

b. The phase angle of the source voltage is angle = arctan(Vo/I).

c.  Peak voltage: Vr = Vp * cos(angle)

d.  Peak voltage across L: Vl = Vp * cos(angle)

e. Peak voltage across C: Vc = Vp * cos(angle)

To solve this problem, we need to use the characteristic equation of an LRC circuit, which is given by:

1 + (2*RC) / (R + jXL) + (2*LC) / (C + jXC) = 0

First, we need to find the values of XL and XC using the impedance ratio formula:

Z = (R + j*XL) / (2*RC) = (2*LC) / (C + j*XC)

Solving for XL and XC, we get:

XL = (RZ - 1)/(2C)

XC = (CZ - 1)/(2R)

Next, we can solve for the peak current using the characteristic equation:

I = (2*RC) / (2RC + 2L*C)

Solving for I, we get:

I = (Vo*t) / (2*R*C)

where t is the time for half a cycle of the source voltage.

The phase angle of the source voltage relative to the current can be found using the following formula:

angle = arctan(Vo/I)

where Vo is the peak voltage of the source voltage and I is the peak current in the circuit.

The peak voltage across R and its phase angle relative to the source voltage can be found using the following formula:

Vr = Vp * cos(angle)

where Vp is the peak voltage across R and angle is the angle we found earlier.

The peak voltage across L and its phase angle relative to the source voltage can be found using the following formula:

Vl = Vp * cos(angle)

where Vp is the peak voltage across L and angle is the angle we found earlier.

The peak voltage across C and its phase angle relative to the source voltage can be found using the following formula:

Vc = Vp * cos(angle)

Learn more about peak current visit: brainly.com/question/27839310

#SPJ4