Zara is having trouble accessing her company's website through her web browser. She has already pinged the static IP address of the web server and it appears to be online. Which of the following might she look at next?
a. Ensure that the server's NTP settings are correct.
b. Verify that the DHCP settings are correct on the server.
c. Ensure that DNS for the domain is configured correctly.
d. Check that the LDAP server is also online.

Linux permissions would assign the owner full access, the group RX access, and everyone else read access. is D. chmod 754 foobar.sh.

Linux uses a permission structure to dictate who can read and write to different files, directories, and other resources. When files and directories are created in Linux, there is a set of rules that dictate who can access the contents of that file.

Linux permissions are divided into three distinct classes: user, group, and others.

The chmod command is a shell command that modifies the permissions on a file or directory. It stands for "change mode" and allows the user to modify the permission settings on a file. A permission is given to each file to decide which user can do what with the file, like read, write, and execute permission.

The permission is divided into three main parts: read, write and execute. The first part is for the owner, the second is for the group, and the third part is for everyone else. The chmod command uses a three-digit number to represent the permissions.

Each digit represents one of the groups of permissions, where the first digit is for the owner, the second digit is for the group, and the third digit is for everyone else.

Linux Permissions that assign the owner full access, the group RX access, and everyone else read access:

Therefore, the answer is D. chmod 754 foobar.sh.

Learn more about Linux at

https://brainly.com/question/30176895

#SPJ11

The need to back up important data before installing new hardware is an example of the following constraint(s): time constraint and cost constraint.

Constraints, also known as limitations or restrictions, are a set of parameters that limit the possible solutions to a specific issue or problem. Constraints come in a variety of forms, and the importance of a given constraint is determined by the problem being addressed. The need to back up important data before installing new hardware is an example of the following constraints:

Time constraint- This implies that there is a limited amount of time available to complete a task, and as a result, we must work within that time frame to accomplish our objectives. In this scenario, a time restriction is present because the installation of new hardware must be completed in a certain amount of time, necessitating the need to back up data before starting the procedure.

Cost constraint- This refers to the financial limits that restrict the amount of money available for the solution's execution. If the cost of backing up the data is too high, it may prohibit the new hardware installation. As a result, it's crucial to consider the cost of implementing a solution when dealing with a problem.

For more such questions on hardware

https://brainly.com/question/28494136

#SPJ11

None of the following is a preventive measure aimed at reducing motor vehicle accidents caused by poor decision-making in young drivers: driver “buddy systems”, increased penalties for violations of driving laws, or driver’s education classes.

The most effective measures to reduce motor vehicle accidents are for young drivers to be taught the rules of the road and to develop good decision-making skills. These measures include: using defensive driving techniques, limiting distractions while driving, avoiding driving while impaired, and understanding the risks of speeding or aggressive driving. Young drivers should also be taught the importance of wearing seatbelts, checking tire pressure and vehicle maintenance, and having emergency preparedness kits in their vehicles. Educating young drivers on these safety measures is essential to reduce motor vehicle accidents.

To learn more about Buddy :

https://brainly.com/question/30908546

#SPJ11

The given problem is asking for the formulas of x(t) and y(t) that could represent the parametric curve (x(t), y(t)).

What is parametric curve?

Parametric curve is the curve that is defined by equations of the form [tex]x=f(t)[/tex] , [tex]y=g(t)[/tex] where t is the parameter.

So, for a given value of t, x and y coordinates can be found by plugging in that value of t. Different values of t will give different points on the curve.

To find the formulas for x(t) and y(t), the following steps can be used:

Step 1: Identify the shape of the curve. Based on the shape of the curve, we can come up with the equation of the curve.

Step 2: Break the curve into x(t) and y(t) components.

Step 3: Choose a parameter to represent the curve. Typically, we use t as the parameter.

Step 4: Determine the x(t) and y(t) components of the curve based on the chosen parameter.

Step 5: Write the equations of x(t) and y(t).

The equations can be simple linear equations or more complex nonlinear equations.

For example, consider a circular path. The equation of a circle can be represented as [tex](x-a)^2+(y-b)^2=r^2[/tex]

Where a and b represent the coordinates of the center of the circle, and r is the radius of the circle.

To find x(t) and y(t), we can rewrite the equation of the circle as: [tex]x=a+r cos(t)[/tex] and [tex]y=b+r sin(t)[/tex]

where t is the parameter.

So, for different values of t, we can get different points on the circle.

Learn more about Parametric curve here:

https://brainly.com/question/30482587

#SPJ11

Tech B is correct. When taking a resistance reading on a lightbulb, the Digital Multimeter (DMM) must be hooked up to each side of the lightbulb with the switch turned on. This is because in order for the DMM to measure the resistance of the lightbulb, there must be a complete circuit with current running through it.  

To measure the resistance of the lightbulb, the DMM needs to measure the voltage drop across the bulb. This voltage drop can only be measured if there is a current flowing through the lightbulb.

So, when the switch is turned on, the current is flowing through the lightbulb, allowing the DMM to measure the voltage drop across it and, in turn, the resistance.  

If the switch is off, there is no current flowing through the lightbulb, so the voltage drop across it will be zero and the DMM will be unable to measure the resistance of the bulb.

Therefore, Tech B is correct and the DMM must be hooked up to each side of the lightbulb with the switch turned on in order to take a resistance reading.

Both the Technicians have different opinions about the resistance reading on a lightbulb.

Tech A says that a resistance reading on a lightbulb requires the DMM to be hooked up to each side of the bulb, while Tech B says that the DMM should be hooked to each side of the bulb and the switch turned on.

For more such questions on Digital Multimeter

https://brainly.com/question/29512413

#SPJ11

The number of binary digits needed to encode a sample is 16 if the Nyquist samples are uniformly quantized into L binary-coded.

There are two basic categories of audio signals: analogue and digital. At the recording and playback ends, all audio is analogue sound, therefore digital sound can be viewed as an analogue sound that has been routed through computational machinery.

In many home theatre systems, PCM is the digital audio format that is used. It is a two-channel format, which means it can support up to two audio channels and deliver stereo sound through two speakers.

To know more about binary visit:-

https://brainly.com/question/10442521

#SPJ1

False. A user interface design that enables users to communicate with the system using natural language is often referred to as a natural language feature in software.

An interface that uses natural (human) language for user and system communication is known as a natural language interface. The system generates responses in the form of utterances provided by speech, text, or another method after the user gives input via speech or another means.

A manufactured language, an artificial language, a machine language, or the language of formal logic are not considered to be natural languages. Instead, they are human languages like English or Standard Mandarin. Also  called ordinary language.

To know more about software visit:-

https://brainly.com/question/985406

#SPJ1

The Domain Name System (DNS) is a hierarchical decentralized naming system that maps human-readable domain names to numerical IP addresses used to locate and identify network resources on the internet. Option A is the correct answer.

DNS acts as a phonebook for the internet by translating domain names, such as www.example.com, into the corresponding IP addresses, such as 93.184.216.34. DNS provides a distributed database that allows for the efficient and reliable resolution of domain names to IP addresses by utilizing a network of servers to handle queries and responses. DNS also supports the mapping of other types of data, such as mail servers and service location records, and is a critical component of the internet infrastructure.

Option A) DNS is the correct answer.

You can learn more about Domain Name System (DNS)  at

https://brainly.com/question/18274277

#SPJ11

Data is ranked using a certain criterion that you choose when sorting.

Data that has been compared to other pieces of data and assigned a "place" in relation to those other pieces of data is known as ranked data. For instance, if the numbers 7.6, 2.4, 1.5, and 5.9 are ranked from least to greatest, 1.5 comes out on top, followed by 2.4, 5.9, and 7.6.

One way to evaluate performance is by ranking. The ranking technique is the most traditional and established type of procedure. This approach compares each employee according to their value. They are arranged from best to worst.

To know more about Data visit:-

https://brainly.com/question/11941925

#SPJ1

The tension in Newtons for the taught side is 104.38 N. The maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN

Given that a belt is tensioned to 704 N whilst stationary in a belt pulley system. the wheel is 184 mm in diameter and 5 kW of power is being transmitted at 334 rev/min.

The formula to calculate the tension in the taught side of a belt pulley system is as follows:

T1 = (P×60)/(2×π×N) + (μ×P×60)/(2×π×N)

Where T1 is the tension in the taught side of the belt pulley system.

P is the power transmitted in kW.

N is the speed of rotation in rpm.

μ is the coefficient of friction in the belt pulley system.

Substituting the given values in the above equation,

T1 = (5×60)/(2×3.14×334) + (0.92×5×60)/(2×3.14×334)

T1 = 95.9 + 8.48T1 = 104.38 N (approx)

Therefore, the tension in Newtons for the taught side is 104.38 N (approx)

2: A technician calculated the coefficient of friction as 0.36 when an engineer wrapped a belt around a drum 2.00 times and then applied a 195 N weight to one of the ends.

The maximum weight that the other end of the pulley system can bear before slippage occurs can be calculated as follows:

μ = (T2 - T1)/W

Where μ is the coefficient of friction in the belt pulley system.

T1 is the tension in the tight side of the pulley system.

T2 is the tension in the slack side of the pulley system.

W is the weight attached to the slack side of the pulley system.

Substituting the given values in the above equation,0.36 = (T2 - 195)/W

Assuming T2 is greater than T1, the total tension can be calculated as follows:

T2 = 2T1T2 = 2(W + 195)W can be calculated as follows:

0.36W = 2W + 3900.64W = 3900W = 6093.75 N (approx)

Therefore, the maximum weight that the other end of the pulley system can bear before slippage occurs is 6.094 kN (approx).

To know more about belt pulley system:https://brainly.com/question/29718602

#SPJ11

1. The tension in Newtons for the taught side is 493.17 N. 2. The maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.

1. Tension = 704 N
Diameter of wheel (D) = 184 mm = 0.184 m
Power (P) = 5 kW = 5000 W
Speed (N) = 334 rpm
We need to find the tension in Newtons for the taught side.
The formula for tension in the belt pulley system is:

T1 - T2 = (P x 60) / (2πN) Here, T1 is the tension in the tight side and T2 is the tension in the slack side.
Substitute the given values in the above formula, we get:
T1 - T2 = (5000 x 60) / (2π x 334)T1 - T2 = 282.33N......(1)
As the bett is tensioned to 704N whilst stationary, we have T1 + T2 = 704N......(2)
Adding equations (1) and (2), we get:2T1 = 986.33NT1 = 493.17 N

Therefore, the tension in Newtons for the taught side is 493.17N.

2. Number of turns (n) = 2
Applied weight (W) = 195 N
Coefficient of friction (µ) = 0.36
We need to find the maximum weight in kN at the other end of the pulley system before slippage occurs.
The formula for maximum weight is:
Maximum weight (Wmax) = µ x n x W......(1)
Substitute the given values in the above formula, we get:
Wmax = 0.36 x 2 x 195

Wmax = 140.4 N

As the required answer is in kN, divide the above answer by 1000.

Wmax = 0.1404 kN.

Therefore, the maximum weight in kN the other end of the pulley system before slippage occurs is 0.1404 kN.

To learn more about "tension": brainly.com/question/11348644

#SPJ11

In an electronic circuit, electrons exit the power source, travel via conductors, perform work in a load, and then return to the power source. The electrons move in a circular direction, which is why it is called a circuit.

How does a circuit work explain?

The conductor travels in a circle from the power source to the resistor and back to the power source. The existing electrons in the wire are moved around the circuit by the power source. This is referred to as a current. Electrons flow from the negative end of a wire to the positive end. A circuit diagram is a simplified depiction of an electrical circuit's components that uses either photos of the individual sections or standard symbols.

Learn more about circuit

https://brainly.com/question/27206933

#SPJ1

a) The 15 kg mass has to fall through a distance of 13.2 m on Mars to impart 250 J of kinetic energy to the rotating uniform drum.

b) The speed of the 15 kg mass on Mars as the drum gains 250 J of kinetic energy is 9.22 m/s.

According to the problem statement provided, the question asks for the distance through which a 15kg mass has to fall on Mars to impart 250 J of kinetic energy to the rotating uniform drum and the speed at which the 15kg mass is moving on Mars as the drum gains 250 J of kinetic energy.

The expression for the kinetic energy of an object is given as:

KE = 0.5mv²

Where, Kinetic energy of an object is represented as KE, Mass of the object is represented as m, Velocity of the object is represented as v.

The work done by the 15 kg mass in imparting kinetic energy to the drum is given as:

Work done = Kinetic energy

The expression for work done is given as:

W = Fs

Where, Work done is represented as W, Force is represented as F, Displacement is represented as s.

If there is no appreciable friction in the axle of the drum, the force required to move the drum is given as the weight of the mass acting vertically downwards. Hence,

F = mg

Where, Mass of the object is represented as m, Gravity of the object is represented as g.

The expression for the work done is given as:

W = Fs ……… (1)

Let the distance through which the mass has to fall on Mars to impart 250 J of kinetic energy to the rotating uniform drum be represented as s. Therefore, work done in the system can be given as:

W = Fsg

Substituting the value of the force, the equation becomes:

W = mgs ……… (2)

the mass of the object, m = 15.0 kg

Distance of the fall on Earth, s = 5.00 m

Work done in the system, W = 250.0 J

The value of g on Earth, gE = 9.81 m/s²

The value of g on Mars, gM = 3.71 m/s²

From equation (1), work done can be written as: W = Fsg ……… (1)

From equation (2), work done can be written as: W = mgs ……… (2)

Equating equations (1) and (2),

Fsg = mgs ……… (3)

Cancelling out s from both sides of the equation,

Fg = mg ……… (4)

From equation (4), Acceleration due to gravity on Earth can be given as:

gE = gG = 9.81 m/s²

Acceleration due to gravity on Mars can be given as:

gM = gM = 3.71 m/s²

We know that, F = mg. Therefore, the expression for the force required can be given as:

F = m*gM ……… (5)

Substituting equations (4) and (5) in equation (3),

m*gM*s = m*gE*5.00 m

Solving for s,

s = gE/gM * 5.00 ms = (9.81 m/s²) / (3.71 m/s²) * 5.00 ms = 13.2 m

Therefore, the 15 kg mass has to fall through a distance of 13.2 m on Mars to impart 250 J of kinetic energy to the rotating uniform drum. Speed can be determined using the formula:

KE = 0.5mv²

Rearranging the above expression, we get,

v = sqrt(2KE/m) ……… (6)

From the problem statement, Mass of the object, m = 15.0 kg. The work done in the system, W = 250.0 J. Substituting these values in equation (6),

v = sqrt(2*250.0 J/15.0 kg)

v = 9.22 m/s

Therefore, the speed of the 15 kg mass on Mars as the drum gains 250 J of kinetic energy is 9.22 m/s.

Learn more about Speed and kinetic energy at : https://brainly.com/question/19891482

#SPJ11

195.96 degrees C and  -59.35 kW is the temperature of the steam after the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber is 1 MPa.

To solve this problem, we need to apply the energy balance and the steam table.

First, we need to determine the state of the geothermal water before the flashing process. Since it enters the flash chamber as a saturated liquid, we can use the steam table to find its properties at the given temperature of 230 degrees C:

h1 = hf + x * hfg = 834.46 kJ/kg (from the steam table)

where h1 is the enthalpy of the geothermal water, hf is the enthalpy of the saturated liquid at 230 degrees C, hfg is the enthalpy of vaporization at 230 degrees C, and x is the quality of the water (which is 0 since it is a saturated liquid).

Next, we need to find the state of the steam after the flashing process. We know that the pressure at the exit of the flash chamber is 1 MPa, and we can assume that the process is adiabatic (no heat transfer). Using the steam table, we can find the enthalpy and quality of the steam at this pressure:

hf = 191.81 kJ/kg (from the steam table)

hfg = 1984.4 kJ/kg (from the steam table)

hg = hf + hfg = 2176.21 kJ/kg

x = (h1 - hf) / hfg = 0.314

where hg is the enthalpy of the saturated vapor at 1 MPa.

Therefore, the temperature of the steam after the flashing process can be found by interpolation:

Tg = 230 + x * (Tsat(1 MPa) - 230) = 230 + 0.314 * (184.97 - 230) = 195.96 degrees C

where Tsat(1 MPa) is the saturation temperature at 1 MPa (from the steam table).

Finally, we can use the steam table again to find the enthalpy of the steam at the exit of the turbine:

hf = 96.83 kJ/kg (from the steam table)

hfg = 2434.4 kJ/kg (from the steam table)

hg = hf + x * hfg = 835.63 kJ/kg

where x is the quality of the steam, which is given as 5%.

Therefore, the power output from the turbine can be calculated as:

P = m * (h1 - hg) = 50 * (834.46 - 835.63) = -59.35 kW

The negative sign indicates that the turbine is consuming power instead of generating power. This is because the quality of the steam at the exit of the turbine is only 95%, which means that there is some moisture content that needs to be removed. To improve the power output, we can use a moisture separator or a reheater to increase the quality of the steam.

To learn more about pressure visit;

https://brainly.com/question/12971272

#SPJ4

Correct question:

In a single-flash geothermal power plant, geothermal water enters the flash chamber (a throttling valve) at 230 dgrees C as a saturated liquid at a rate of 50 kg/s. The steam resulting from the flashing process enters a turbine and leaves at 20 kPa with a moisture content of 5%. Determine the temperature of the steam after the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber is 1 MPa.

The c) calibrated torque wrench method is a commonly used method to ensure that bolts in slip-critical bolted connections are properly tensioned(c).

This method involves using a torque wrench with a calibrated gauge to tighten the bolts to a specified torque value. The torque value is calculated based on the size and grade of the bolt and the material being joined. This method is effective because it allows for precise control over the amount of tension applied to each bolt.

Additionally, it can be used on-site, making it a convenient option for construction projects. While other methods such as the turn of nut method and direct tension indicator can also be used, the calibrated torque wrench method is generally preferred due to its accuracy and reliability.

Spline tension control bolts, on the other hand, are a different type of fastener that rely on the splines to prevent the nut from loosening, rather than on specific torque or tension requirements.

For more questions like Torque wrench click the link below:

https://brainly.com/question/19104073

#SPJ11

Goal Seek is used in Excel to determine the value that a certain cell needs to be changed to in order to reach a specific goal, by altering the value of another cell that is related to the goal cell through a formula or calculation.

When you use Goal Seek, you select a cell that contains a formula and specify the value that you want that formula to return by changing the value in another cell. Excel then uses a trial-and-error approach to determine the value that needs to be entered into the input cell to achieve the desired result.

For example, you might use Goal Seek to determine how much you need to save each month in order to reach a specific savings goal by a certain date. You would set the savings goal as the cell to be changed, and the monthly savings amount as the input cell to be adjusted until the goal is met.

Learn more about Goal Seek https://brainly.com/question/30404127

#SPJ11

The new array will look like this after the given operations: [10, 20, 50].

ArrayListPrepend(list, 10): In this operation, 10 is added at the beginning of the list, which makes the new array (10, 20, 30, 40, 50). ArrayListSearch(list, 25): In this operation, we try to find the element 25 in the list. Since there is no such element in the list, the function will return -1. So, the array remains unchanged as (10, 20, 30, 40, 50). ArrayListRemoveAt(list, 2): In this operation, the element at index 2 (i.e. 30) is removed from the list. So, the new array becomes (10, 20, 40, 50). ArrayListSearch(list, 40): In this operation, we try to find the element 40 in the list. It is present at index 2. So, the function will return 2. The array remains as (10, 20, 40, 50).Therefore, the new array will look like this after the given operations: [10, 20, 50].

Learn more about ArrayList: https://brainly.com/question/20464124

#SPJ11

One contact not closing  is a probable cause of relay-controlled equipment failing to start when the contactor is closed

Now you may ask, why do we need to use a contactor? Can't we just connect the motor to the PLC? The simple answer is no.Why? Because you don't want to connect a high-voltage electric motor directly to your expensive PLC. If there are any electric surges on the motor's side, the PLC cards will be damaged.Instead, we use a contactor to connect the PLC to the motor in an indirect and safe manner. What do we mean by "indirectly," you may wonder. All contactors, after all, have a low voltage coil. The PLC output is connected to this coil. This coil is typically powered by a 24-volt DC signal.When the coil is turned on, an electromagnetic field is created.

To know more about Contactor, click on the link :

https://brainly.com/question/28146701

#SPJ1

The Complete Question is:- Which of the following is a probable cause of relay-controlled equipment failing to start when the contactor is closed?

Structural Integrity The crane's main body, crawler music and/or outrigger supports, boom sections, and attachments are all considered part of the structural integrity of lifting.

The crane's essential body and crawler tune are considered a part of the structural integrity of lifting. In areas wherein gentle floor poses a assist hassle, mats and/or blocking off need to be used to distribute a crane's load and to keep a stage stable condition.
A safe Load Indicator (SLI) or an automatic safe Load Indicator (ASLI) is a device that's established on cellular or portal cranes to alert the operator if the carry is exceeding the safe operating variety of the machinery.

To realize extra about structural integrity click here
brainly.com/question/24180542
#SPJ4

Answer:

Explanation: Three-phase power is a three-wire ac power circuit with each phase ac signal 120 electrical degrees apart

If you encounter icing conditions during climb-out after takeoff and with the autopilot engaged, you can expect the autopilot to adjust the aircraft's pitch and power to maintain a constant airspeed, which may not be sufficient to prevent ice buildup on the wings and other critical surfaces.

In such a situation, it is essential to take immediate action to ensure the safety of the flight.

This may include turning off the autopilot and manually adjusting the pitch and power to maintain a safe speed and altitude, activating the aircraft's anti-icing systems, and communicating with air traffic control to request clearance to climb to a higher altitude or change your flight path to avoid the icing conditions.

Learn more about Autopilot at:

https://brainly.com/question/20372893

#SPJ1

With regard to the dimension,

a) Therefore, the best cross-section for a rectangular channel is a width of 3.172 m and a depth of 1.086 m.

(a) Rectangular channel:

The hydraulic radius of a rectangular channel is half the depth of flow, and the cross-sectional area is equal to the product of the width and depth.

Let's assume the depth of flow as "y" and the width of the channel as "b". Then, the cross-sectional area of the channel is:

A = b * y

The wetted perimeter of the rectangular channel is:

P = b + 2y

The hydraulic radius is:

R = A/P = (b*y) / (b+2y)

The discharge Q is given as:

Q = VA = R * (b*y) * sqrt(S)

where S is the bottom slope, and V is the average velocity of the flow.

We are given Q = 2 m^3/s, and S = 0.001. Let's assume the velocity of flow as "v".

Substituting the values, we get:

2 = (by) * sqrt(0.001) * (by) / (b + 2y)

Solving for y, we get:

y = 1.086 m

Substituting this value in the equation for b, we get:

b = 3.172 m

Therefore, the best cross-section for a rectangular channel is a width of 3.172 m and a depth of 1.086 m.

Learn more about dimensions  at:

https://brainly.com/question/28688567

#SPJ1

Answer:

Explanation:

270

The given statement "an electrical connection between an electrically conductive object and a component of a lightning protection system that is intended to reduce potential differences created by lightning currents is an example of bonding." is true. It is because an electrical connection between an electrically conductive object and a component of a lightning protection system that is intended to reduce potential differences created by lightning currents is an example of bonding.

Bonding is the process of connecting two or more electrically conductive objects together to ensure that they have the same electrical potential. Bonding is an essential element of lightning protection systems because lightning currents can create large potential differences between objects, which can lead to dangerous electrical arcs or sparks. By bonding all conductive objects together, potential differences are minimized, and the risk of electrical damage is reduced.

You can learn more about Bonding at

https://brainly.com/question/18258856

#SPJ11

The cost should be increased by 50% or 0.5 fraction.

If there are 100,000,000 of these parts in service, how many lives would you predict to be lost?

The cost of this part varies linearly with the cross-sectional area (for the same length part, to double the cross-sectional area requires twice as much steel and twice the cost) The stress experienced by this part varies inversely and linearly with the cross-sectional area (you can imagine part as being in pure tension).

By what fraction would you increase the cost of the part?

The probability of the steel pin to fail, P(f) can be computed by the following formula:

P(f) = P(S> Sy)

Where P(S> Sy) is the probability of stress exceeding the yield stress. The value of P(S> Sy) can be calculated as follows:

Z= (S - μ)/σZ = (60 - 51)/3= 3P(S> Sy) = P(Z > 3) = 0.0013

Z= (S - μ)/σZ = (80 - 51)/5= 5.8P(S> Sut) = P(Z > 5.8) = 0.0000041

The probability of yielding (failure) can be computed as:

P(failure) = P(Sy < S < Sut) = P(S > Sy) - P(S > Sut) = 0.0013 - 0.0000041 = 0.001296

The number of parts in service = N = 100,000,000

Expected number of failures = N * P(failure) = 100,000,000 * 0.001296 = 129,600 lives are expected to be lost

The cost of the part is proportional to the cross-sectional area, A. If we assume the cross-sectional area to be doubled, then the cost will be doubled too.The stress, S is inversely proportional to A.

Therefore if A is doubled, then S will reduce by half (1/2) that is:S1/S2 = A2/A1S2= S1 (A1/A2)S2= 51 ksi (2/1)S2= 102 ksi

The fraction by which we should increase the cost is given as:

(Cost at S1/Cost at S2)= (Area at S1/Area at S2)= (1/2) = 0.5

Therefore, the cost should be increased by 50% or 0.5 fraction.

Learn more about Fraction:

brainly.com/question/6201432

#SPJ11

Horizontal components of reaction at A is 0 N

Vertical components of reaction at A is 3200 N

Reaction at B on the beam is 900 N.m

Lets solve the question in detail.

The horizontal and vertical components of reaction at A, as well as the magnitude of the reaction at B on the beam, can be determined with the given information. Let's start by calculating the reaction at point A:

The horizontal reaction at A = F1cos(90°) = 1200cos(90°) = 0 N
The vertical reaction at A = F1sin(90°) + F2sin(0°) = 1200sin(90°) + 2000sin(0°) = 3200 N

Now, let's calculate the reaction at B:
Reaction at B = F1sin(90°) + F2sin(90°) = 1200sin(90°) + 2000sin(90°) = 3200 N
Magnitude of the reaction at B = √[(1200sin(90°))2 + (2000sin(90°))2] = √[(1200)2 + (2000)2] = 900 N.m

Therefore, the horizontal components of reaction at A is 0 N, the vertical components of reaction at A is 3200 N, and the reaction at B on the beam is 900 N.m.

Learn more about components of reaction.

brainly.com/question/1443888

#SPJ11

The Code's requirement to ground equipment typically implies that there will be a direct connection to the earth or a connection to ground through a b) grounding electrode or c) a grounding electrode conductor.

The equipment grounding conductor is used to provide a low-impedance path to ground for fault current. The grounding electrode is a conductive object that is in direct contact with the earth and is used to provide a stable reference point for the electrical system.

The grounding electrode conductor is used to connect the grounding electrode to the electrical system's grounding conductor. Therefore, the answer is (d) Any of the above, as all of these options could be used to provide the required grounding for the equipment.

For more questions like Code click the link below:

https://brainly.com/question/3417943

#SPJ11

The ways of arranging the storage so that you can meet the specifications set by your boss:

The first method for organizing a storage system is RAID. It is one of the most reliable methods for protecting data from hard drive failure. The RAID system uses several hard drives and combines them into a single volume. Data is then written across the drives, thus ensuring that if one fails, there is no data loss.A backup is an excellent method to safeguard data against potential loss due to hardware or software failure. Your storage system should have a routine backup schedule that backs up critical data regularly. The use of cloud storage is increasing in popularity. Cloud storage is a great way to safeguard data against loss due to hardware or software failure.

Learn more about RAID: https://brainly.com/question/28963056

#SPJ11

Answer:

#include <iostream>

using namespace std;

class EvenNumber

{

   private:

   int integrer;

   public:

   EvenNumber ()

   {

       integrer=0;

   }

   EvenNumber (int number)

   {

   integrer=number;

   }

   int getvalue ()

   {

       return integrer;

   }

   int getnext ()

   {

       return integrer+2;

   }

   int getprevious ()

   {

       return integrer-2;

   }

};

int main () {

   EvenNumber sixteen(16);

   cout<<"The value is: "<<sixteen.getvalue()

   <<" the next even number is: "<<sixteen.getnext()<<

   " and the previous number is: "<<sixteen.getprevious();

   return 0;

}

Explanation: