The given output that matches the characters with asterisks are:
print('*****')print(' ')print('*****')print(' ')print('*****')What is the Print function?The print() function outputs the message to the normal output device, such as the screen. The message can be a string or any other object, and before it is displayed on the screen, the object will be changed into a string.
This is used to display the output of a desired result and is an important part of aspect of programming as it helps to show the output./
Read more about print command here:
https://brainly.com/question/13243443
#SPJ1
Output the following figure with asterisks. Do not add spaces after the last character in each line.
*****
*****
*****
Note: Whitespace (blank spaces / blank lines) matters; make sure your whitespace exactly matches the expected output.
in order to prove the correctness of this algorithm, start by showing the following property: any square of size d d in the plane contains at most four points of l. (b) now show that the algorithm is correct. the only case which needs careful consideration is when the closest pair is split between l and r
The two methods below are both intended to calculate the sum of squares from 1 to n, where n is any positive number.
To obtain the inverse of a given function, follow these steps: The square root is 2 added, 3 divided, 2 subtracted. The task is assigned to us; begin with the letter "n" Add 2. Increase the outcome by 3. Deduct 10 from that outcome. Square the resultant figure. A function that reverses the effects of another function is called an inverse function. Thus, the following are the methods to obtain the inverse of the aforementioned function: The square root is 2 added, 3 divided, 2 subtracted. The two methods below are both intended to calculate the sum of squares from 1 to n, where n is any positive number. A set of instructions known as an algorithm is used to solve problems by doing calculations, data processing, and automated reasoning.
Learn more about An inverse function here:
https://brainly.com/question/28573734
#SPJ4
an axial force p is applied to the shaft with thrust bearing shown. the bearing consists of a circular collar a that is bonded to the shaft b. applying a factor of safety of 1.5, determine the maximum axial force p that can be applied to the shaft without exceeding the allowable shear stress along cylindrical surface a or b. (shear failure along surface a would mean that whatever is used to bond the collar to the shaft has failed. shear failure along surface b would mean that the fixture c, which prevents the collar from moving to the right, has failed). both the bonding material and the material from which part c is made have a failure shear stress of 255 mpa.
The maximum axial force that can be applied to the shaft is 382.5 kN.The maximum axial force that can be applied to the shaft is 382.5 kN.
What is the significance of the failure shear stress of 255 MPa for the bonding material and fixture used in the thrust bearing?The failure shear stress of 255 MPa is a critical parameter for the bonding material and fixture used in the thrust bearing. This value represents the maximum shear stress that the material can withstand before it fails, and is an important consideration in designing the thrust bearing to support the applied axial force. If the applied force exceeds the allowable shear stress, the bonding material or fixture may fail, leading to catastrophic failure of the bearing and damage to the shaft or other components. Therefore, it is essential to ensure that the maximum axial force is calculated and limited to a level that does not exceed the failure shear stress of the bonding material or fixture.
To know more about Axial Force visit:
https://brainly.com/question/13137098
#SPJ4
What are the symbols in a circuit?
Electrical symbols are the ones most frequently used in circuit diagrams. Amplifiers (shown by triangle shapes) in your circuit amplify the output signal. Your system's capacitors (parallel lines) store energy, but resistors (zigzag lines) lower current flow.
Which five electrical symbols are there?Electrical terminology uses the following five symbols: switch, wire, contactor, motor, and transformer. Any electrical sketch can use these icons.
What constitutes a circuit?A basic circuit has the three elements that are required to establish a working electric circuit, namely a source of voltage, a conductive route, and a resistor. The route an electric current takes is known as a circuit.
To know more about electrical visit:-
brainly.com/question/13019820
#SPJ4
Which of the following statements best describes the relationship of cost to communication in a design-bid-build process?
Communication is timely and fast because all phases work together in a single team, which keeps costs from mistakes low.
Communication is timely and fast because all phases work together in a single team, which keeps costs from mistakes low.
The separation of phases into distinct parts with different teams means that communication doesn’t flow as freely between phases, which can lead to misunderstandings and cost overruns from mistakes.
The separation of phases into distinct parts with different teams means that communication doesn’t flow as freely between phases, which can lead to misunderstandings and cost overruns from mistakes.
The communication process in the design-bid-build is often confusing, which can lead to misunderstandings and cost overruns from mistakes.
The communication process in the design-bid-build is often confusing, which can lead to misunderstandings and cost overruns from mistakes.
Communication flows through well-defined channels, ensuring project leaders get the specific information they need to keep projects running efficiently without costly mistakes.
The statement that best describes the relationship of cost to communication in a design-bid-build process is:
"The separation of phases into distinct parts with different teams means that communication doesn't flow as freely between phases, which can lead to misunderstandings and cost overruns from mistakes." (Option C)
What is the justification for the above response?In the design-bid-build process, different teams typically handle different phases of the project, such as design, pre-construction, and construction. This separation of phases can make communication between teams more difficult and lead to misunderstandings, which can result in costly mistakes and delays.
Therefore, effective communication and coordination are critical to managing costs in a design-bid-build process, and the lack of communication can result in cost overruns and delays.
Learn more about communication at:
https://brainly.com/question/12623594
#SPJ1
Find the linear approximation of the following functions (using Taylor series): (a) e^xu close to equilibrium point x=0,u=1
The correct answer is Using a Taylor series, a number is approximated by a polynomial whose value is extremely close to the value of the number in the vicinity of a given x value: f (x) equals f (a) plus f ′ (a) 1! ( x − a ) + f ′ ′ ( a ) 2 !
Near x=a, the second-order Taylor polynomial approximates f(x) more well than the linear approximation (which is the same as the first-order Taylor polynomial). We may use it to do things like determine the local minimum or maximum of the function f. (x). By utilising the formula L(x) = f(a) + f '(a) (x - a), where f '(a) is the derivative of f(x) at an x = a, one may determine the linear approximation, which is indicated by L(x). The difference between an exact value and an approximation to it is the approximation error in a data value.
To learn more about Taylor click on the link below:
brainly.com/question/29733106
#SPJ4
it is illegal to improperly dispose of antifreeze.
Yes, that's correct. Improper disposal of antifreeze is illegal because it can be harmful to the environment and to wildlife.
What is Antifreeze?
Antifreeze is a toxic substance and if it is not disposed of properly, it can contaminate groundwater and other bodies of water, which can have devastating effects on the ecosystem. Additionally, antifreeze can be attractive to animals and birds because of its sweet taste, but it is highly toxic and can cause death if consumed in even small quantities.
In many jurisdictions, it is required by law to properly dispose of antifreeze by taking it to a recycling center or hazardous waste facility. The specific regulations vary from place to place, so it is important to check the local laws and guidelines in your area to ensure that you are properly disposing of antifreeze and other hazardous waste materials.
To learn more about hazardous waste, visit: https://brainly.com/question/28615813
#SPJ4
That when printing a string, it prints characters at increasing memory addresses until we reach the null terminator (byte 0x00). True or False
That when printing a string, it prints characters at increasing memory addresses until we reach the null terminator (byte 0x00) .
The correct answer is True .
What are some common operations that can be performed on strings in C++, such as concatenation, slicing, and comparison?In C++, strings are usually handled as an array of characters, which means that they can be manipulated the usage of various capabilities and operators. A few not unusual operations that can be completed on strings in C++ encompass concatenation, which entails joining two or greater strings collectively to create a brand new string. Other operations encompass reducing, which entails extracting a portion of a string based on its position or duration, and evaluation, which involves evaluating two strings to determine if they are equal or if one is greater or much less than the other. Different not unusual operations on strings encompass locating the duration of a string, trying to find particular characters or substrings, and enhancing or changing characters inside a string.
To know more about Encompass visit:
https://brainly.com/question/13753880
#SPJ4
Task 6: Create a new directory called "Test.Dir" using the mkdir command. After it is created, delete the directory by using the rmdir command. I Task 7: We now want to navigate to the directory logically one level above us, so we will use the change directory command, "cd ..". Now we want to move up another level, so we will run the command again. We then want to move back into the original directory, so we will use the cd command again, this time we will use the relative path, which starts with a ./ and then should be pointed to ust/[username).
To create and delete the "Test.Dir" directory, we used the mkdir and rmdir commands. To move up one level, we used the change directory command (cd ..). To move back, we used the relative path cd ./[username].
To create a new directory called "Test.Dir" we used the mkdir command. This command creates a directory with the name specified. Once this directory was created, we then wanted to delete it. To delete the directory, we used the rmdir command. This command removes the specified directory.
After we had created and deleted the directory, we wanted to navigate to the directory logically one level above us. To do this, we used the change directory command, "cd ..". This command moves us one level up the directory tree. We then wanted to move up another level, so we ran the command again.
Finally, we wanted to move back into the original directory, so we used the cd command again. This time, we used the relative path which starts with a ./ and then should be pointed to ust/[username]. This command allows us to move back to the original directory.
Learn more about Commands here-
https://brainly.com/question/30319932
#SPJ4
add the following two's complement binary numbers. what is the decimal value of each addend? what is the decimal value of the sum? is there overflow? (remember that when there's overflow, the sum doesn't match what is expected from the addition. show the decimal value of the binary sum, not what was expected from adding the decimal values.)
Binary operators are defined as those that operate on two operands.
A simple method for assessing numerical values and character strings is provided by operators, which are stated using special characters.
What are operations and the many varieties of them?In computer science, an operator is a letter or group of letters that determines the action to be executed or the elements to be considered. Arithmetic players, relation operations, and logical operators are the three main types of operators used by programmers.
How is an operator defined in C?To put it another way, an operator is a symbol that tells the compiler to do specific logical, mathematical, or conditional operations. It performs as a symbol on an integer or even a variable. The operators to utilize, for instance, are + and -.
To know more about operator visit:
https://brainly.com/question/29765525
#SPJ4
A centric load P is applied to the granite block shown. The resulting maximum value of the shearing stress in the block is 3.4 ksi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 6 in. 6 in. Determine the normal stress exerted on that surface. (Input the answer with the appropriate sign.) The normal stress exerted on that surface is ___ksi.
The presented statement states that -3.4ksi is the typical stress applied to the surface.
What causes shear stress?The element of tension that acts perpendicular to a substance cross section is known as shear stress. The most frequent cause of shear stress here is that when forces are exerted in a straight line parallel to a surface, such as when blood flows through vascular tissue and interacts with the artery wall, causing fluid shear stress.
What really is shear stress easily explained?"A sort of stress who acts coplanar with the cross - sectional area of material," is how shearing stress is defined. Shear forces cause shear stress to develop. They are a pair of equal-but-opposed-direction forces that are acting on separate sides of a body.
Normal stress on that surface at θ=45°
бθ= σysin²θ
so, =-244.8/36*sin²45
so, =-3.4ksi
To know more about shear stress visit:
https://brainly.com/question/14418799
#SPJ4
Given variables strength, speed, and direction, declare and assign the following pointers:
integer pointer strengthPointer is assigned with the address of strength.
double pointer speedPointer is assigned with the address of speed.
character pointer directionPointer is assigned with the address of direction.
Ex: If the input is 5 35.0 N, then the output is:
Hurricane level: 5
Speed: 35.0 miles per hour
Direction: N
#include
#include
using namespace std;
int main() {
int strength;
double speed;
char direction;
/* Your code goes here */
cin >> strength;
cin >> speed;
cin >> direction;
cout << "Hurricane level: " << *strengthPointer << endl;
cout << "Speed: " << fixed << setprecision(1) << *speedPointer << " miles per hour" << endl;
cout << "Direction: " << *directionPointer << endl;
return 0;
}
Integer pointer strengthPointer is assigned with the address of strength.
#include <iostream>
#include <iomanip>
using namespace std;
int main()
{
int strength;
double speed;
char direction;
/* Your code goes here */
//initialized strength pointer
int * strengthPointer = &strength;
//initialized speed pointer
double * speedPointer = &speed;
//initialized direction pointer
char * directionPointer = &direction;
cin >> strength;
cin >> speed;
cin >> direction;
cout << "Hurricane level: " << *strengthPointer << endl;
cout << "Speed: " << fixed << setprecision(1) << *speedPointer << " miles per hour" << endl;
cout << "Direction: " << *directionPointer << endl;
return 0;
}
A pointer variable is declared same like a normal variable but contains asterisk * in between data type and variable name.
E.g. int * variable_name;
Also to initialize a pointer we provide it address of same data type.
e.g. if there is an integer type variable x, then a pointer named p will have address of x as:
p = &x;
or both initialization and declaration can be done together as:
int * p = &x;
Here is the sample output of above code:
Learn more about pointer
https://brainly.com/question/30460618
#SPJ1
that type of construction which walls, partitions, and structural members are of non-combustible materials, but do not qualify as fire resistive.
Type 2 buildings have non-combustible walls, partitions, columns, floors, and roofs, much like Type 1 structures do.
Although these buildings frequently have fire suppression system, they are unstable and frequently lack fire-resistant coatings. The outside walls and structural parts of Type III building, commonly referred to as ordinary construction, must be composed of noncombustible or minimally combustible materials like concrete blocks or day tile blocks. The highest quality non-combustible materials, such as poured concrete and fire-resistant steel framing, are used to construct Type I buildings, which are rated to withstand fires for two to three hours. The greatest degrees of safety are offered by this rating.
Learn more about system here-
https://brainly.com/question/27162243
#SPJ4
vhdl processes and equivalent symbolic circuit representation a. write a vhdl process that is equivalent to the following concurrent statement: a
In VHDL, a concurrent statement is a signal assignment that occurs outside of a standard process construct but within the architecture. A concurrent assignment is another name for the concurrent statement.
In VHDL, what are the two concurrent statements?There are two concurrent versions of sequential statements provided by VHDL: concurrent signal assignments and procedure calls. A previously defined (hardware) component is referred to in the component instantiation statement. Finally, any concurrent statements are duplicated using the generate statement.
What is an example of concurrency?Multiple computations are occurring simultaneously with concurrency. Whether we like it or not, concurrency is present everywhere in modern programming: A network of multiple computers. On one computer, multiple applications are running.
To know more about VHDL visit :-
https://brainly.com/question/30025695
#SPJ4
if the tension developed in either cable ab or ac can not exceeded 800 lb, the maximum tension that can be developed in cable ad when it is tightened by the turnbuckle is [ select ] lb. also, the force developed along the antenna tower at point a is [ select ] lb?
In the direction from A to E, the force created along the antenna at point A is roughly 1998 lb.
Where is the stress at its highest?The tension in the string is largest at the mean position and minimal at the extreme position for a simple oscillating pendulum.
We can apply the method of sections to calculate the maximum tension in cable AD. A slice through cables AB and AD reveals the following:
Sum of vertical forces = 0
T_AD*sin(60) - T_AB = 0
T_AD = T_AB/sin(60) = T_AB/0.866
Taking a section through cables AC and AD, we have:
Sum of vertical forces = 0
T_AD*sin(60) - T_AC = 0
T_AD = T_AC/sin(60) = T_AC/0.866
Since the tension in either cable AB or AC cannot exceed 1000 lb, the maximum tension that can be developed in cable AD is:
T_AD = 1000/0.866 = 1154 lb (rounded to the nearest lb)
To determine the force developed along the antenna at point A, we can use the method of joints. Taking joint A, we have:
Sum of horizontal forces = 0
F_AEcos(30) + T_ADcos(60) = 0
F_AE = -T_ADcos(60)/cos(30) = -T_ADsqrt(3) = -1998 lb (rounded to the nearest lb, assuming T_AD = 1154 lb)
To know more about maximum tension visit:-
https://brainly.com/question/13251741
#SPJ4
Find the concentration in (a) mg/L, (b) ppm, (c) ppb, and (d) moles/L (M), respectively, for the following solution: 1.5 g of NaCl dissolved in 500 mL of water The total organic carbon concentration of a water is 4 mu g/L. Express this concentration in units of (a) mg/L, (b) ppm, and (c) ppb. The air quality standard of SO_2 is 0.14 ppm. Check to see if the measured SO_2 concentration of 450 mu g/m^3 at 25 degree C and latm exceeds the standard.
(a) 1.5 g/500 mL = 3000 mg/L; (b) 3000 mg/L = 3 ppm; (c) 4 mu g/L = 0.004 ppb; (d) 1.5 g/500 mL = 0.003 M. (a) 4 mu g/L = 0.004 mg/L; (b) 0.004 mg/L = 0.004 ppm; (c) 0.004 ppm = 4 ppb. Yes, the measured SO_2 concentration exceeds the standard.
The concentration of a solution can be expressed in different units. For the given solution of 1.5 g of NaCl dissolved in 500 mL of water, the concentration can be expressed in (a) mg/L, (b) ppm, (c) ppb, and (d) moles/L (M). To convert to mg/L, the mass of solute (1.5 g) is divided by the volume of solution (500 mL), resulting in 3000 mg/L. To convert to ppm, the concentration of 3000 mg/L is multiplied by 1000, resulting in 3 ppm. To convert to ppb, the concentration of 4 mu g/L is divided by 1000, resulting in 0.004 ppb. To convert to moles/L, the mass of NaCl (1.5 g) is divided by its molar mass (58.44 g/mol), then multiplied by 1000 to get the volume (L) of the solution, resulting in 0.003 M. For the given total organic carbon concentration in water, 4 mu g/L, this can be converted to (a) mg/L by multiplying by 1000, resulting in 0.004 mg/L. To convert to ppm, the concentration of 0.004 mg/L is multiplied by 1000, resulting in 0.004 ppm. To convert to ppb, the concentration of 0.004 ppm is multiplied by 1000, resulting in 4 ppb. For the given air quality standard of SO_2 of 0.14 ppm, and the measured SO_2 concentration of 450 mu g/[tex]m^3[/tex] at 25 degree C and latm, the measured SO_2 concentration exceeds the standard.
Learn more about concentration here
https://brainly.com/question/10725862
#SPJ4
TRUE OR FALSE at a constant temperature, newtonian fluids exhibit a constant of proportionality, which is the fluid's
True. At a constant temperature, Newtonian fluids have a constant viscosity which is the proportionality constant between the shear stress and the shear rate.
True. Newtonian fluids are a class of fluids that exhibit a linear relationship between the rate of shear and the shear stress. This relationship is described by the Newton's law of viscosity, which states that the shear stress is directly proportional to the rate of shear, with the constant of proportionality being the fluid's viscosity. At a constant temperature, this constant of proportionality remains constant for Newtonian fluids, making them ideal fluids for many engineering applications, as their behavior can be easily predicted and modeled. In contrast, non-Newtonian fluids do not follow this linear relationship, and their viscosity may change with time, pressure, or shear rate, making their behavior more complex and difficult to predict.
Learn more about Newtonian fluids here:
https://brainly.com/question/17585633
#SPJ4
where is the torque converter clutch solenoid located
The torque converter clutch solenoid is located in the transmission, usually either in the valve body or mounted to the transmission case.
What is Torgue?
Torgue is a brand of weapons and ammunition manufactured by the company, Torgue Corporation, in the Borderlands universe. Torgue weapons are known for their high damage output, usually at the cost of accuracy or fire rate. Torgue products are often highly explosive, focusing on area of effect damage, and feature a distinctive orange and yellow color scheme. The company is also known for its colorful and aggressive advertising campaigns, often featuring the slogan "More Boom, Less Wimp!" Torgue weapons excel when fighting large groups of enemies, and are often favored by those looking for maximum destruction.
To know more about Torque
https://brainly.com/question/20691242
#SPJ4
The ball has a mass m and is attached to the cord of length l. The cord is tied at the top to a swivel and the ball is given a velocity v_0. Show that the angle theta which the cord makes with the vertical as the ball travels around the circular path must satisfy the equation tan theta sin theta = upsilon^2_0/gl. Neglect air resistance and the size of the ball.
The string of length l is used to secure the mass m of the ball. The ball is given a velocity of v 0, and the cord is attached at the top to a swivel.
When the ball goes around the circular path, demonstrate that the angle theta that the cord makes with the vertical must meet the equation tan theta sin theta = upsilon2 0/gl. A 5 lb particle's course of travel in the horizontal plane is denoted by the polar coordinates r=(2t+1)ft and =(0.5t2t)rad, where t is measured in seconds. For t=2s, calculate the size of the imbalanced force affecting the particle. A string of length L with a pivot point at point O holding a ball of mass m is attached.
Learn more about length here:
https://brainly.com/question/30100801
#SPJ4
is circuit switching which are true dedicated circuit connection overhead requires reassebly
No, circuit switching creates a dedicated connection and does not require reassembly of data packets, making it a more efficient method of communication.
No, circuit switching creates a dedicated connection between the sender and receiver that does not require packet reassembly, making it more efficient for transmitting data over an uninterrupted connection.
This method is commonly used in telephone networks to ensure reliable and uninterrupted communication.
While circuit switching is efficient and reliable, it is less flexible than packet switching.
Packet switching breaks data into packets for transmission, allowing for greater flexibility and network resource sharing.
The choice between circuit switching and packet switching depends on the specific needs of the application or network being used.
Learn more about circuit switching here:
https://brainly.com/question/14402768
#SPJ4
What is definition Forensic Science?
the use of scientific or technical methods to identify, gather, analyze, and evaluate evidence for matters of criminal and civil law or regulation
Which two terms best describe forensic science?The application of natural sciences to legal issues is known as forensic science. In actual practice, forensic science makes use of ideas and procedures from physics, chemistry, biology, and other branches of science. The appraisal of physical evidence includes its identification, individualization, and recognition by forensic scientists.
What makes it forensic science?The Roman term forensis, which means public, to the forum or public conversation; argumentative, rhetorical, belonging to dispute or discussion, is where the word "forensic" originates. The phrase "related to, employed in, or fit for a court of law" is a valid definition of forensic in today's society.
To know more about technical methods visit:-
brainly.com/question/19819958
#SPJ4
Consider the diagram of a hydroelectric plant above. If
you wanted to increase the amount of electricity the
plant produced, what changes would you make to the
design of the plant? Explain why these changes would
increase the electrical output.
There are several ways to increase the electrical output of a hydroelectric plant:
Increase the flow of water: By increasing the amount of water that flows through the plant, the turbines will spin faster, generating more electrical power.
What is the hydroelectric plant?Other ways are:
Increase the head (or height) of the water: The amount of energy that can be generated by a hydroelectric plant is proportional to the head of water, which is the height of the water above the turbine. By increasing the head of water, the potential energy of the water is increased, which can be converted into more electrical power.
Upgrade the turbines: Upgrading the turbines to more efficient models can increase the amount of power that can be generated from the same amount of water flow.
In general, any changes that increase the amount of water flowing through the turbines, increase the head of water, or improve the efficiency of the turbines will result in an increase in the electrical output of the hydroelectric plant. However, the specific changes that are needed will depend on the design of the plant and the characteristics of the water source.
Learn more about hydroelectric plant from
https://brainly.com/question/2321474
#SPJ1
What is the current divider formula?
The ratio of individual (branch) current to total current and total resistance to individual resistance are equivalent. When the total current is known, it is a quick way for figuring out branch currents in a parallel circuit.
What is the purpose of a current divider?The primary function of the current divider is to generate a portion of the circuit's total available current. The component that is utilized to convey the current, though, occasionally has a limit on how much current may pass through it.
Why is a device referred to as a current divider?Due to its capacity to proportionately divide the total current into fractional components, a parallel circuit is frequently referred to as a current divider.
To know more about circuit visit:-
https://brainly.com/question/20067088
#SPJ4
polarity can be changed on a welding machine by pushing a button, rotating a selector switch, or changing how the cables are attached to the machine.
The polarity of a welding machine can be changed by pushing a button, rotating a selector switch, or adjusting the cable connections. Each method alters the current flow to achieve the desired result.
Welding machines are used to join two pieces of metal together using heat and pressure. The welder must have control of the electrical current in order to properly join the metals. The polarity of the welding machine determines the direction of the electrical current and is essential for successful welding. Changing the polarity can be done in several ways. By pressing a button, rotating a selector switch, or changing the way the cables are attached to the machine, the current flow can be reversed to achieve the desired result. Each method will provide the welder with the control they need to successfully weld the metals together. Understanding how to change the polarity of a welding machine is an important part of the welding process and will ensure that the weld is of the highest quality.
Learn more about connections here-
brainly.com/question/14327370
#SPJ4
What is the optimum replacement time interval?
The best replacement period will vary depending on the particular item being considered as well as a number of criteria like the item's intended use and the manufacturer's recommendations.
Does ETOPS apply to aircraft with four engines?The new ETOPS requirement does not apply to freighters with three and four engines. Additionally, this regulation formalizes polar policy obligations for operators whose intended air routes cross the North and South Polar regions.
When was ETOPS put into action?For these reasons, the US enacted the initial rules that would later develop into the ETOPS criteria that are familiar to us today in 1953. These first regulations limited the routes that two- or three-engine aircraft might take in order to enforce the "60-minute rule."
To know more about manufacturer's visit:-
https://brainly.com/question/30289320
#SPJ4
1.
-Assume you are given an int variable named nPositive and a 2-dimensional array of ints that has been created and assigned to a2d. Write some statements that compute the number of all the elements in the entire 2-dimensional array that are greater than zero and assign the value to nPositive. (4 pts)
-Write a 'main' method that examines its command-line arguments and (3 pts)
calls the (static) method displayHelp if the only argument is the class name. Note that displayHelp accepts no parameters
otherwise, 'main' calls the (static) method argsError if the number of arguments is less than four. argsError accepts the number of arguments (an integer) as its parameter
otherwise, 'main' calls the (static) method processArgs, which accepts the command-line argument array as its parameter.
-Write the Java code to create an array with 4 integers: 3, 8, 7, 6. Declare and initialize this array in your code and then compute the mean value of these 4 numbers (you must use a loop). (3 pts)
1.int nPositive = 0;for (int i = 0; i < a2d.length; i++) {for (int j = 0; j < a2d[i].length; j++) { if (a2d[i][j] > 0) {nPositive++; } } }
What is Positive?
Positive is having a positive outlook on life. It is the attitude of looking at the bright side of things and having an optimistic view of life. Positive thinking can help to reduce stress, improve mental and physical health, and increase overall happiness. Positive thinking can be cultivated through mindfulness, gratitude practices, and reframing negative thoughts.
2.public static void main(String[] args) { if(args.length == 1 && args[0].equals(MyClass.class.getName())) {displayHelp(); } else if (args.length < 4) {argsError(args.length);} else { processArgs(args); } }
3.int[] myArray = {3, 8, 7, 6};int sum = 0;for (int i=0; i<myArray.length; i++) {
sum += myArray[i]; } double mean = sum/myArray.length;
To learn more about Positive
https://brainly.com/question/28632127
#SPJ4
for which there is an institutional network connected to the Internet. Suppose that the average object size is 850,000 bits and that the average request rate from the institution’s browsers to the origin servers is 16 requests per second. Also suppose that the amount of time it takes from when the router on the Internet side of the access link forwards an HTTP request until it receives the response is three seconds on average (see Section 2.2.5). Model the total average response time as the sum of the average access delay (that is, the delay from Internet router to institution router) and the average Internet delay.For the average access delay, use Δ/(1 – Δ·β), where Δ is the average time required to send an object over the access link and β is the arrival rate of objects to the access link.Find the total average response time.Now suppose a cache is installed in the institutional LAN. Suppose the miss rate is 0.4. Find the total response time
The total average time required to send an object over the access link and β is the arrival rate of objects to the access link is 3.349 seconds
Elaborating the problem:The average access delay, use δ/(1 − δβ)
where :
δ is the average time required to send an object .
β is the arrival rate of objects to the access link.
a) Total average response time:
δ = 850,000 bits / 16000000 bps = 0.0531 Sec
δβ = 0.053 sec/request × 16 request/sec = 0.848
δ/(1 − δβ) = 0.0531/(1-0.848)
= 0.0531/ 0.152
= 0.349
Total average response time= 0.349+3 = 3.349 Sec
b) Total response time
miss rate =0.4
miss rate + hit rate = 1.0 (100%)
hit rate = 1.0 - 0.4 = 0.6
Since 60% of requests are fulfilled within the institutional Network, the traffic intensity on the access link is reduced by 60%, resulting in an average access delay of 0.0531 / (1-0.349 ×0.848)
= 0.0531/(1-0.2959)
= 0.0531/0.7
= 0.075 seconds
When the cache fulfills the request, which has a probability of 0.6, the response time is nearly zero.
The average response time is 0.075+ 3 seconds.
= 3.075 seconds ( which happens 40 % of the time)
So average response time = 0.6 × 0 sec + 0.4 × 3.075 sec
= 1.23 seconds
Thus the average response time reduced from 3.349 seconds to 1.23 seconds.
What does the LAN serve?Sharing resources is the primary purpose of LANs. When connected to a network, expensive hardware like CD/ROM drives and laser printers can be shared by multiple users. Additionally, the cost of purchasing software for each computer is reduced by purchasing a network version.
Learn more about LAN network:
brainly.com/question/14242759
#SPJ1
Use the following transfer function G(s) to evaluate the root locus conditions for each of the cases given. This system G(s) is in the feedback given in Problem 2 with a proportional controller. s+5 K(s) = K G(s) = 8+ $6 + 28 (a) Use the root locus angle condition to show that it is possible to place a closed loop pole at -2. Find the gain K that will place a pole at this location. (b) Use the root locus angle condition to show that it is not possible to place any closed loop pole at -7. (c) Use the root locus angle condition to show that it is possible to place a closed loopP pole at -15. Find the gain K that will place a pole at this location. 2. Consider the feedback loop below with plant G(s) and proportional controller K(s) = K. Use the Routh- Hurwitz criterion to determine the full range of K that produces a stable feedback system GcL(s). s+6 G(s) = 3 + 4s2 + 3s R(S) K(s) G(s)
A mathematical function that theoretically represents the output of a system, sub-system, or component for each potential input is called a transfer function in engineering. Electronics and control systems use them extensively.
How do transfer function and Six Sigma relate to one another?Transfer functions, a key element of Design for Six Sigma, offer the necessary connections between design, process, and materials characteristics and the CTQs in the cycle of developing products and processes.
Are transfer function and frequency response the same?In reality, a system's frequency response can be determined by replacing s = j to determine its transfer function. The frequency response H(j) is typically complex, including both real and fictitious components. Polar coordinates are frequently more helpful and understandable when used to convey this.
To know more about transfer function visit :-
https://brainly.com/question/13002430
#SPJ4
which of the following input field devices would most likely be used with an analog interface input module?
A photocell is the input field device most likely to be used in an analog interface input module.
What principle is used in photocells?Photocells work on the principle that when photons of sufficient energy strike a metal surface, electrons leave the metal surface, converting light energy into electrical energy.
What kind of device is a photocell?A photocell is a resistor that changes resistance depending on the amount of light that hits it. Photocells work on the photoconductivity of semiconductors. The energy of photons striking the semiconductor releases electrons, which flow and reduce resistance.
What are photocell used for?A photocell is an optoelectronic device that operates on the principle of the photoelectric effect. It is mainly used to detect light of suitable wavelength. Photocells generate energy through the process of the photoelectric effect.
To learn more about photocell visit:
https://brainly.com/question/21537818
#SPJ1
A reciprocating piston compressor has the following:
-Piston diameter of 300mm,
-Stroke of 450mm,
-Intake pressure of 1 bar,
-Intake temperature of air at 200C,
-Clearance volume of 3%,
-Rotational speed N = 250rev/min,
-Discharge pressure = 40 bar,
-Compression and Re-expansion are polytropic process with k = 1.25
a) Find the compressor’s characteristics (V,P T at all points A,B, C, D).
b) Calculate the work and power of the compressor.
The work and power of the compressor are 599.68 kJ/kmol and 57772.8 kW respectively.
What is compressor ?A compressor is a device used to compress, or reduce the size of, data. It is used to reduce the amount of space taken up by a file so that it takes up less storage space, or to reduce the amount of bandwidth required for streaming or transmission. Compressors can also be used to reduce the size of audio or video files for easier storage, or for faster transmission over the internet. The compressor characteristics can be calculated using the ideal gas law equation and the polytropic equation.
At point A (intake pressure and temperature):
[tex]V = (RT/P) = (287*200/1) = 57.4 m3/kmol[/tex]
P = 1 bar
T = 200C
At point B (Compression):
[tex]V2/V1 = (P2/P1)^(1-k)V2 = V1 * (P2/P1)^(1-k)V2 = 57.4 * (40/1)^(1-1.25) = 16.31 m3/kmolP2 = 40 barT2 = T1 * (V2/V1)^(k-1)T2 = 200 * (16.31/57.4)^(1.25-1) = 585.6C[/tex]
At point C (Clearance volume):
[tex]V3 = V2 * (1+3/100) = 16.68 m3/kmol[/tex]
P3 = P2 = 40 bar
T3 = T2 = 585.6C
At point D (Discharge pressure):
[tex]V4/V3 = (P4/P3)^(1-k)V4 = V3 * (P4/P3)^(1-k)V4 = 16.68 * (1/40)^(1-1.25) = 57.78 m3/kmol[/tex]
P4 = 1 bar
[tex]T4 = T3 * (V4/V3)^(k-1)T4 = 585.6 * (57.78/16.68)^(1.25-1) = 197.6C[/tex]
b)The work of the compressor can be calculated using the following equation:
[tex]Work = (P2*V2 - P1*V1)/kWork = (40*16.31 - 1*57.4)/1.25 = 599.68 kJ/kmol[/tex]
The power of the compressor can be calculated using the following equation:
[tex]Power = (2*π*N*Work)/60Power = (2*3.14*250*599.68)/60 = 57772.8 kW[/tex]
The work and power of the compressor are 599.68 kJ/kmol and 57772.8 kW respectively.
To learn more about compressor visit
brainly.com/question/29345949
#SPJ1
If the electric field between the plates of a given capacitor is weakened, the capacitance of that capacitor:
a) increases.
b) decreases.
c) does not change.
d) cannot be determined from the information given.
The capacitance of a given capacitor does not change if the electric field between its plates is weakened. Hence, the given option C. is correct.
What is Capacitance in this question?
The capacitance of a capacitor is determined by the properties of its plates (such as their area and separation distance), and the dielectric material between the plates, and is unaffected by the intensity of the electric field between the given plates.
If the electric field is weakened or get low intensity, this would result in a decrease in the voltage across the capacitor, but the capacitance would remain unchanged.
To learn more about Capacitance, visit: https://brainly.com/question/30426172
#SPJ4