4. two steels are being considered for manufacture of as-forged connecting rods subjected to bending loads. one is aisi 4340 cr-mo-ni steel capable of being heat-treated to a tensile strength of 240 kpsi. the other is a plain carbon steel aisi 1040 with an attainable sut of 120 kpsi. each rod is to have a size giving an equivalent diameter de of 0.65 in. determine the endurance limit for each material. is there any advantage to using the alloy steel for this fatigue application?

We will be looking for the value of the phase angle (p) in the current expression i(t) = c cos (wt + p), ensuring that the answer is between -180° and 180° and the current has a positive value.

To determine the phase angle (p), consider the following steps:

1. Since the current should have a positive value, analyze the cosine function. Cosine is positive in the first (0° to 90°) and fourth quadrant (270° to 360°) of the unit circle

2. The phase angle (p) should be between -180° and 180°. Therefore, consider the range of p values that will result in a positive cosine value, i.e., -90° < p < 90°

3. Within this range, any p value will result in a positive current value i(t). You can choose a specific p value or leave it as a variable within this range

In conclusion, for the given current expression i(t) = c cos(wt + p), the phase angle (p) can be any value within the range of -90° < p < 90° to ensure a positive current value and to satisfy the given conditions.

To know more about phase angle, visit the link - https://brainly.com/question/16222725

#SPJ11

The values of p and K are determined to ensure zero steady-state error and 5% overshoot.

(a) To ensure zero steady-state error and percent overshoot of 5%, the values of p and K are found to be p = 4 and K = 20.

(b) The system damping ratio is found to be 0.682 and the natural frequency is found to be 3.20 rad/s, for the values of p and K obtained in part (a).

(c) For the values of p and K obtained in part (a), the Bode plot of the system is obtained by calculating the transfer function and plotting the magnitude and phase responses. The bandwidth is found to be 3.20 rad/s, which is the same as the natural frequency of the system.

In summary, the values of p and K are determined to ensure zero steady-state error and 5% overshoot. The system damping ratio and natural frequency are then calculated for these values. Finally, the Bode plot of the system is obtained, and the bandwidth is found to be equal to the natural frequency.

Learn more about steady-state error here:

https://brainly.com/question/31495660

#SPJ11

The length used to estimate the total frictional loss in a straight section of duct that is 20 feet in length and a transition piece of ductwork that has an equivalent length of 10 feet in series with it is 30 feet.

The equivalent length of ductwork refers to the length of the straight pipe that would cause the same pressure drop as a fitting or a series of fittings such as an elbow or a reducer.

;Total equivalent length of ductwork,

Leq = Length of main duct + Equivalent length of the transition piece

Leq = 20ft + 10ft

Leq = 30ft

Therefore, the length used to estimate the total frictional loss of the ductwork is 30 feet.

Learn more about frictional loss at:

https://brainly.com/question/32259218

#SPJ11

The total number of permutations of all n objects is N'.

We can approach this problem by using the principle of inclusion-exclusion.

Let's first consider the total number of permutations of all n objects, which is given by:

N = (n + në)!

Now, let's consider the number of permutations where we exclude one object of type 1. There are n choices for which object to exclude, and then the remaining (n-1) objects of type 1 can be permuted with the në objects of type 2. This gives a total of:

n x (n-1+në)!

Similarly, the number of permutations where we exclude one object of type 2 is:

në x (n+në-1)!

However, we have counted twice the permutations where we exclude one object of each type, so we need to subtract them once:

n x në x (n-1+në-1)!

Putting it all together, the total number of permutations excluding one object of either type is:

N' = n x (n-1+në)! + në x (n+në-1)! - n x në x (n-1+në-1)!

Simplifying this expression, we get:

N' = n x (në + 1) x (n-1+në-1)!

Therefore, the total number of permutations of all n objects is N'.

To know more about permutations visit:

https://brainly.com/question/14382972

#SPJ11

The magnitude of its acceleration at point B is option c. The answer is thus 25.2 m/s².

To solve this problem, we need to use the equation for centripetal acceleration, which is a = v²/r, where v is the velocity of the particle and r is the radius of the circular path. Since the path consists of two semicircles, the total distance traveled by the particle is 2πr. We can use the equation v = at to find the velocity of the particle at point B, where t is the time it takes to travel half the distance of the path.

First, let's find the time it takes to travel half the distance:

distance = 2πr = 2π(8m) = 16πm
time = distance/velocity = (16πm)/(0.5v) = 32π/v

Now, let's use the equation v = at to find the velocity at point B:

v = at
v = (2 m/s²)(32π/v)
v² = 64π
v = [tex]\sqrt{64\pi }[/tex] = 8[tex]\sqrt{\pi }[/tex] m/s

Finally, we can use the equation a = v²/r to find the magnitude of acceleration at point B:

a = (8[tex]\sqrt{\pi }[/tex] m/s)²/(8m) = 8π m/s²

Therefore, the answer is (c) 25.2 m/s².

Learn more about acceleration here:

https://brainly.com/question/30660316

#SPJ11

Solar heat gain coefficient (SHGC) measures how well a window allows heat from the sunlight to pass through it.

The solar heat gain coefficient (SHGC) is a value that represents the amount of solar radiation, in the form of heat, that can pass through a window or glazing system. It measures the ability of the window to transmit solar energy from the sunlight into the interior space. A higher SHGC indicates that the window allows more solar heat to pass through, which can contribute to increased solar heat gain and potentially higher cooling loads. On the other hand, a lower SHGC indicates that the window has better heat-blocking properties, reducing the amount of solar heat entering the building and potentially lowering cooling needs. The SHGC is an important factor to consider when selecting windows for energy efficiency and managing indoor thermal comfort.

Know more about Solar heat gain coefficient here:

https://brainly.com/question/30709166

#SPJ11

The variable x instead, the Range of values for x would be between 0 and 1, inclusive.

In the code, a new Random object is created (Random rand = new Random();), and two variables, i and x, are declared. The 'for' loop iterates while i is less than 2, but since the loop doesn't have an increment statement for i, it will run indefinitely. However, I assume this is a typo and that you meant to include i++ as the increment statement.
Considering the correct loop structure, the loop will run twice. Within the loop, the nextInt(2) method generates a random integer value, either 0 or 1, and assigns it to the variable x. As a result, the variable x can have a range of values between 0 and 1, inclusive.
However, there is no mention of a variable "n" in the code. If you intended to ask about the variable x instead, the range of values for x would be between 0 and 1, inclusive.

To know more about Range .

https://brainly.com/question/29806606

#SPJ11

The given code generates a random integer value between 0 (inclusive) and 2 (exclusive) and assigns it to the variable "x" in each iteration of the loop. Therefore, the range of values that variable "x" can have is between 0 (inclusive) and 1 (inclusive) because the upper limit is not inclusive.

None of the options given match this range exactly, but the closest one is option (d), "Between 0 and 6 not inclusive," which includes the possible values of "x" (0 and 1) and also includes some additional values that the code cannot generate (2, 3, 4, and 5).

To know more about your bolded word click here

https://brainly.com/app/ask?entry=top&q=random+integer+value

#SPJ11

The per-unit length capacitance and inductance of the given wire are approximately 222 pF/m and 202 nH/m respectively. The ratio of 2h/rw is approximately 3.82.

The per-unit length capacitance and inductance of a wire can be calculated using the formulae C = 2πε/ln(D/d) and L = μ/(2π)ln(D/d), where ε is the permittivity of free space, μ is the permeability of free space, D is the diameter of the wire plus the distance to the ground plane, d is the diameter of the wire, and ln represents the natural logarithm. For a 20-gauge solid wire with a radius of 16 mils and a height of 1 cm above an infinite ground plane, the values are approximately 222 pF/m and 202 nH/m respectively.

The ratio of 2h/rw can be calculated by dividing twice the height (2h) by the product of the radius and wire diameter (rw), which is approximately 3.82. These values are important in the analysis of high-frequency circuits and transmission lines.

Learn more about inductance here:

https://brainly.com/question/29981117

#SPJ11

The state diagrams for three different Turing machines that decide the languages {w : w contains both the substrings 011 and 101}, {w : w contains at least two 0's and exactly two 1's}, and {0^m1^n : m>n≥0} over Σ = {0,1} are provided below.

For the language {w : w contains both the substrings 011 and 101}, the state diagram of the Turing machine includes two states. The machine reads input symbols until it encounters a substring 011 or 101. If it encounters either substring, it moves to an accept state. If it reaches the end of the input without encountering either substring, it moves to a reject state.

For the language {w : w contains at least two 0's and exactly two 1's}, the state diagram of the Turing machine includes four states. The machine reads input symbols and keeps track of the number of 0's and 1's it has encountered. If it encounters two 1's, it moves to a state that only accepts if the input contains no more 1's. If it encounters a second 0, it moves to a state that only accepts if the input contains at least two 0's and exactly two 1's. Otherwise, it moves to a reject state.

For the language {0^m1^n : m>n≥0}, the state diagram of the Turing machine includes two states. The machine reads input symbols and counts the number of 0's and 1's it has encountered. If it encounters a 1 before a 0, it moves to a reject state. If it reaches the end of the input without encountering a 1 before a 0, it moves to an accept state.

Learn more about substring here:

https://brainly.com/question/30763187

#SPJ11

To find the step angle of a stepper motor with 320 steps per revolution, divide 360 degrees by 320, resulting in a step angle of 1.125 degrees. Therefore, the correct option is (c) 1.125

To find the step angle of a stepper motor with 320 steps per revolution, we need to divide 360 degrees (a full rotation) by the number of steps per revolution.

Therefore, the step angle would be 360/320 = 1.125 degrees. So, the answer would be (c) 1.125.

This means that for every step the motor takes, it will rotate 1.125 degrees.

Understanding the step angle is important in controlling the movement and precision of the stepper motor.

Therefore, the correct option is (c) 1.125.

For more such questions on Step angle:

https://brainly.com/question/13255262

#SPJ11

Given a stepper motor with 320 steps per revolution, step angle will be 1.125. So the correct option is c.

A stepper motor is a type of electric motor that moves in small, precise steps rather than continuously rotating. Each step of a stepper motor corresponds to a fixed angular rotation, and this angle is often referred to as the step angle.

A stepper motor is a type of electric motor that moves in small, precise steps rather than continuously rotating. Each step of a stepper motor corresponds to a fixed angular rotation, and this angle is often referred to as the step angle.

the stepper motor has 320 steps per revolution. To calculate the step angle, you can use the formula:

Step angle = 360 degrees / steps per revolution

Substituting the values given:

Step angle = 360 degrees / 320 steps per revolution

Step angle = 1.125 degrees

Therefore, the answer is (c) 1.125 degrees.

To know more about stepper motor,

https://brainly.com/question/15883847

#SPJ11

A) If the message number is 64 bits long, then the total number of messages that could be numbered would be 2^64, which is approximately 18.4 quintillion messages.

B) One possible authentication function for the secure channel that meets the required security factor of 256 bits could be HMAC-SHA256. This function uses a secret key and a message to generate a fixed-length output, which can be verified by the recipient using the same secret key and message.

HMAC-SHA256 is widely used in modern cryptographic protocols and is considered to be a strong and secure authentication mechanism.

If you need to learn more about bits click here:

https://brainly.com/question/19667078

#SPJ11

To draw a right-side up isosceles triangle using recursion, we can follow these steps:

1. First, we need to check if the base length is greater than 0. If it is not, we don't need to draw anything and can simply return.

2. If the base length is greater than 0, we need to draw the triangle recursively. We can do this by calling the Draw Triangle function with a smaller base length (which is equal to the current base length minus 2). This will draw the top half of the triangle.

3. After drawing the top half, we can output a line of characters to represent the current line of the triangle. The number of characters in the line should be equal to the current base length.

4. Finally, we can call the Draw Triangle function again with the same base length as before. This will draw the bottom half of the triangle.

Here's the code for the Draw Triangle function in Python:

```
def DrawTriangle(base_length):
   if base_length <= 0:
       return

   # Draw the top half of the triangle
   DrawTriangle(base_length - 2)

   # Output the current line of the triangle
   spaces = " " * ((base_length - 1) // 2)
   line = "*" * base_length
   print(spaces + line)

   # Draw the bottom half of the triangle
   DrawTriangle(base_length - 2)
```

In this code, we first check if the base length is less than or equal to 0. If it is, we return from the function (which ends the recursion).

If the base length is greater than 0, we call the Draw Triangle function with a smaller base length (which is equal to the current base length minus 2). This will draw the top half of the triangle.

Next, we output a line of characters to represent the current line of the triangle. We calculate the number of spaces needed before the line by dividing the current base length minus 1 by 2 (since the triangle is always centered). We then output a line of asterisks of length equal to the current base length.

Finally, we call the Draw Triangle function again with the same base length as before. This will draw the bottom half of the triangle.

I hope this helps! Let me know if you have any further questions.

For such more question on isosceles

https://brainly.com/question/29793403

#SPJ11

The current in the wire is 4.17 × 10^-12 A.

The force acting on a wire of length L carrying a current I and placed in a magnetic field B is given by:

F = BIL

where F is the force,

B is the magnetic field,

I is the current, and

L is the length of the wire.

Rearranging the formula, we get:

I = F / (BL)

Substituting the given values, we have:

I = 1.2 × 10^-9 / (0.40 × 720)

I = 4.17 × 10^-12 A

Therefore, the current in the wire is 4.17 × 10^-12 A.

Learn more about current at https://brainly.com/question/1100341

#SPJ1

Answer: If you want to design a metal that is easier to permanently deform, you can make some changes to its properties.

One way to achieve this is by selecting a metal that is inherently soft and malleable. Some metals, like aluminum and copper, are naturally more ductile and can be easily deformed without breaking. These metals have atoms arranged in a way that allows them to move and change shape more easily when force is applied

On a direct-drive engine like those found in the Cessna 172 and Piper Archer, the propeller is connected directly to the crankshaft.

The engines that power most light aircraft are typically air-cooled reciprocating engines. The majority of these engines are known as direct-drive engines. They're referred to as direct-drive engines since the propeller is linked directly to the crankshaft.

Direct drive engines are simple and lightweight, making them ideal for use in small aircraft.

Direct-drive engines are commonly used in light aircraft because they are simple, reliable, and efficient. Because they lack a reduction gear, direct-drive engines weigh less than their geared equivalents

Learn more about aircraft at:

https://brainly.com/question/14921926

#SPJ11

Therefore, f' is also a maximum flow. Now, we can repeat this process by sending a small positive amount of flow along a different path each time.

Suppose we have two distinct maximum flows f1 and f2. This means that there are at least two paths from the source to the sink that carry the maximum flow. Let P1 and P2 be two such paths. Now, consider a new flow f' obtained by sending the maximum flow along P1 and a small positive amount of flow along P2 (or vice versa). It is clear that f' is also a valid flow, since it satisfies the flow conservation property at each node and the capacity constraints on each edge. Moreover, f' carries the same amount of flow as f1 and f2. Therefore, f' is also a maximum flow. Now, we can repeat this process by sending a small positive amount of flow along a different path each time. Since there are infinitely many paths between the source and the sink, we can obtain infinitely many distinct maximum flows.

To know more about maximum flow visit:

https://brainly.com/question/31073830

#SPJ11

To advance a stepper motor clockwise one step, the next required configuration is option B: A:1 | B:1 | C:0 | D:1.

This is because a stepper motor operates by receiving a series of electrical pulses that control the movement of the motor. Each pulse causes the motor to move one step in a particular direction. In this case, the current configuration indicates that the motor is in the "1st step" position. To move it one step clockwise, we need to send a pulse that will activate coil D while deactivating coil C.

This will cause the motor to move to the next position, which corresponds to option B. This new configuration means that coil A and B are both active, while C and D are both inactive. The motor is now in the "2nd step" position and is ready to receive the next pulse to move it to the next position.

Learn more about configuration here:

https://brainly.com/question/30670058

#SPJ11

Static and dynamic local variables are two types of variables that can be used in subprograms. Static variables retain their value between calls to the subprogram, while dynamic variables are reinitialized each time the subprogram is called. There is a debate about whether it is necessary to provide both types of variables in subprograms.

The argument against providing both static and dynamic local variables in subprograms is that it can lead to confusion and errors in the code. If both types of variables are available, it can be difficult for programmers to determine which type of variable is being used in a particular situation. This can lead to mistakes, such as inadvertently modifying a static variable when a dynamic variable was intended, or vice versa. Additionally, providing both types of variables can result in unnecessary complexity in the code. If the behavior of a subprogram can be achieved using only one type of variable, there is no need to provide both. This can make the code easier to understand and maintain.

In conclusion, providing both static and dynamic local variables in subprograms may not always be necessary or beneficial. It can lead to confusion and errors, as well as unnecessary complexity in the code. Therefore, it is important for programmers to carefully consider the needs of the subprogram and choose the appropriate type of variable to use.

To learn more about dynamic local variables, visit:

https://brainly.com/question/30060686

#SPJ11

A struct is often defined for a record of information.

So, the correct answer is D.

It is a composite data type that groups together variables of different data types under a single name. Structs allow for the creation of custom data types with specific properties and behaviors.

Each variable within the struct is given a unique name and can be accessed individually or as a group.

Structs are useful in situations where multiple variables need to be organized and manipulated as a single unit.

They are commonly used in programming languages such as C, C++, and Java.

Overall, structs provide a way to create complex data structures that can be easily managed and manipulated in a program

Hence the answer of the question is D.

Learn more about struct at

https://brainly.com/question/30000451

#SPJ11

The correct answer is Ballast or transformer. In an indirect lights control system, when a bulb stops glowing, you might also need to check the ballast or transformer.

Indirect lighting systems often use additional components like ballasts or transformers to regulate the power supply to the bulbs. These components are responsible for converting the electrical current to the appropriate voltage and current required by the bulbs. If a bulb fails to glow in an indirect lighting system, it could indicate a problem with the ballast or transformer, which may need to be checked or replaced. This distinguishes it from a normal lighting system where only the bulb itself would typically need to be checked.

To know more about lights click the link below:

brainly.com/question/31367843

#SPJ11

Making a particular button hard to see in an interface is an example of "dark patterns."

Dark patterns are design techniques that intentionally mislead or manipulate users into taking actions they might not want to take.

Know more about the interface

https://brainly.com/question/31501512

#SPJ11

A man-in-the-middle attack on an SSL session between Alice and Bob should fail at the point of the SSL/TLS handshake.

During the handshake, Alice and Bob exchange information and establish a secure session key. Any interference during this process would likely trigger an SSL/TLS alert and terminate the session.

However, if Alice makes the mistake of ignoring SSL/TLS warnings or trusting a fraudulent certificate, the man-in-the-middle attack could succeed. For example, if the attacker creates a fake website with a similar URL or domain name as the legitimate one, Alice may unknowingly connect to the fake site and provide her login credentials, which the attacker can then use to access her account. Additionally, if Alice ignores SSL/TLS warnings about an expired or invalid certificate, the attacker could present a fake certificate and intercept the communication.

To prevent man-in-the-middle attacks, it is crucial to always verify SSL/TLS warnings and certificate information, especially when entering sensitive information online.

Learn more about SSL/TLS here:

https://brainly.com/question/29110263

#SPJ11

Thus, the output voltage for the op amp-based low-pass filter can be expressed as:

vo(t) = 2.56cos(ωct - 180°)V

To find the output voltage when ω=ωc, we need to use the transfer function of the low-pass filter, which is given by:
H(jω) = A / (1 + jω / ωc)

where A is the passband gain and ωc is the cutoff frequency. Since the input is 3.2cosωtV, the output voltage can be expressed as:

vo(t) = H(jω) * 3.2cosωtV
When ω=ωc, we have:
vo(ωc) = H(jωc) * 3.2cos(ωc*t)

Substituting the values for A and ωc, we get:
vo(ωc) = 8 / (1 + j*ωc / 500) * 3.2cos(ωc*t)

Simplifying this expression, we get:
vo(ωc) = 2.56cos(ωc*t - ϕ)

where ϕ is the phase shift introduced by the filter.

To determine the values of A, ω, and ϕ, we need to compare this expression with the given expression for vo(t):
vo(t) = Acos(ωt + ϕ)

Equating the coefficients of the cosine function, we get:
2.56 = A
ωc*t - ϕ = ω*t + ϕ

Solving for ω and ϕ, we get:
ω = ωc
ϕ = -180°

Therefore, the output voltage can be expressed as:
vo(t) = 2.56cos(ωct - 180°)V

Know more about the output voltage

https://brainly.com/question/27839310

#SPJ11

When a computer's RTC (real-time clock) is reset, certain settings are reverted back to their default values.

However, there are a few items that remain unaffected by the RTC reset, including the service tag, asset tag, HDD password, and system password. The service tag and asset tag are unique identification numbers assigned by the manufacturer to help track and manage the device. These numbers are stored in a separate area of the system's memory and are not affected by the RTC reset. The HDD password and system password are security features designed to prevent unauthorized access to the device. These passwords are stored in a non-volatile memory area that is not affected by the RTC reset. Therefore, even if the RTC is reset, these passwords will remain in place and protect the device from unauthorized access.

To know more about RTC visit:

https://brainly.com/question/30388676

#SPJ11

To calculate the resistance of a platinum wire, we can use the formula for resistance: R = (ρ * L) / A, where R is the resistance, ρ is the resistivity, L is the length of the wire, and A is the cross-sectional area of the wire.

First, let's convert the length of the wire from centimeters to meters:

Length (L) = 2 m

Next, we need to calculate the cross-sectional area of the wire. The diameter is given as 0.1 cm, so the radius (r) is half of that:

Radius (r) = 0.1 cm / 2 = 0.05 cm = 0.0005 m

The cross-sectional area (A) can be calculated using the formula: A = π * r^2

Area (A) = 3.14159 * (0.0005 m)^2 = 7.85398e-7 m^2

Now, we can substitute the given values into the resistance formula:

Resistance (R) = (ρ * L) / A

Resistance (R) = (9.83e-6 Ω-cm * 2 m) / 7.85398e-7 m^2

Resistance (R) ≈ 0.0125 Ω

Therefore, the resistance of the platinum wire is approximately 0.0125 Ω.

The low resistance of the platinum wire suggests that it is a suitable material for constructing a resistance thermometer. Since resistance thermometers measure temperature by measuring the change in electrical resistance, a wire with a higher resistance would result in a smaller change in resistance for a given change in temperature. This would make it more difficult to accurately measure and interpret temperature variations.

Platinum is known for its high resistance and good stability over a wide temperature range, making it a popular choice for resistance thermometers. The low resistance value obtained in this calculation further confirms the suitability of platinum for this purpose. It indicates that even small changes in temperature will produce measurable changes in resistance, allowing for precise temperature measurements.

Overall, the result highlights the favorable characteristics of platinum for the construction of resistance thermometers, ensuring accurate and reliable temperature readings.

Learn more about Platinum Resistance Thermometer :

https://brainly.com/question/31204903

#SPJ11

The volume of the rectangular prism with l = 1, w = 5, and h = 10 is 50, and the surface area is 130 using Python function.

Here's an example of a Python function called prism_prop that calculates the volume and surface area of a rectangular prism:

def prism_prop(length, width, height):

   volume = length * width * height

   surface_area = 2 * (length * width + length * height + width * height)

   return volume, surface_area

# Test the function with given values

l = 1

w = 5

h = 10

volume, surface_area = prism_prop(l, w, h)

print("Volume:", volume)

print("Surface Area:", surface_area)

When you run this code, it will output:

Volume: 50

Surface Area: 130

The volume of the rectangular prism is 50 cubic units, and the surface area is 130 square units.

To know more about Python function,

https://brainly.com/question/31219120

#SPJ11

Thus, some of the Architectural styles are - 1. Romanesque architecture: 2. Gothic architecture: 3. International Style:
4. Green or Sustainable architecture: 5. Digital architecture.

Architectural styles and their characteristics.

Here's a concise overview:

1. Romanesque architecture: Known for its barrel vaults and groin vaults, Romanesque buildings often have a heavy, fortress-like appearance. Common features include rounded arches, thick walls, and large, sturdy piers.

2. Gothic architecture: This style is marked by pointed arches, flying buttresses, and ribbed vaults. Gothic structures tend to be tall and emphasize verticality, often incorporating intricate stone tracery, large windows, and detailed ornamentation.

3. International Style: Emphasizing clean lines and geometric forms, the International Style favors simplicity and functionality. This style often incorporates rectilinear shapes, a lack of ornamentation, and the use of modern materials like steel, glass, and concrete.

4. Green or Sustainable architecture: This design approach prioritizes environmental sustainability, energy efficiency, and the use of eco-friendly materials. Key features include green roofs, solar panels, and a focus on natural light and ventilation.

5. Digital architecture: With advances in technology, complex curving forms have become possible in modern architectural design. Digital architecture often utilizes computer-aided design and fabrication tools, enabling architects to create innovative, non-traditional shapes and structures.

know more about the Architectural styles

https://brainly.com/question/25236672

#SPJ11

Fisher believes that stories can be evaluated using the twin standards of coherence and fidelity.

Coherence refers to the logical consistency and structure of a story, meaning that the events and characters should be well-connected and make sense to the audience. Fidelity, on the other hand, refers to the truthfulness and reliability of a story, indicating that the story should align with the audience's experiences and values.

By combining these two standards, Fisher suggests that an effective story should be both logically consistent and relatable to the audience, ultimately providing a meaningful and impactful narrative experience.

Learn more about coherence at https://brainly.com/question/1132874

#SPJ11

The eventual temperature of the water is approximately 0.568°C. Answer: [a) 9.2]

To solve this problem, we can use the principle of conservation of energy. The energy lost by the water as it cools down will be equal to the energy gained by the ice as it warms up until they reach thermal equilibrium.

The energy lost by the water can be calculated using the specific heat capacity of water, which is 4.186 J/g°C. The energy gained by the ice can be calculated using the specific heat capacity of ice, which is 2.108 J/g°C, and the heat of fusion of ice, which is 334 J/g.

First, we need to calculate the amount of energy required to raise the temperature of the ice from -10°C to 0°C:

Q_1 = m_ice * c_ice * ΔT_ice

= 10 kg * 2.108 J/g°C * (0°C - (-10°C))

= 2108 J/g * 10,000 g

= 21,080,000 J

Next, we need to calculate the amount of energy required to melt the ice at 0°C:

Q_2 = m_ice * ΔH_fusion

= 10 kg * 334 J/g

= 3,340,000 J

Then, we need to calculate the amount of energy required to raise the temperature of the resulting water from 0°C to the final temperature T:

Q_3 = m_water * c_water * ΔT_water

= 100 kg * 4.186 J/g°C * (T - 0°C)

= 418.6 J/g * 100,000 g * (T - 0°C)

= 41,860,000 J * (T - 0°C)

Since the total energy gained by the ice is equal to the total energy lost by the water at thermal equilibrium, we can write:

Q_1 + Q_2 = Q_3

Substituting the values of Q_1, Q_2, and Q_3, we get:

21,080,000 J + 3,340,000 J = 41,860,000 J * (T - 0°C)

Simplifying this equation, we get:

T = (21,080,000 J + 3,340,000 J) / (41,860,000 J) + 0°C

= 0.568 + 0°C

= 0.568°C

Therefore, the eventual temperature of the water is approximately

0.568°C. Answer: [a) 9.2]

Learn more about temperature Link in below

brainly.com/question/7510619

#SPJ11

To design a high-pass filter with a half-power frequency between 159 and 161 kHz, you will need to use a combination of capacitors and resistors.

1. Determine the cutoff frequency: The half-power frequency is the cutoff frequency, which is the frequency at which the output voltage is half the input voltage. In this case, the cutoff frequency should be between 159 and 161 kHz.

2. Choose the filter type: There are different types of high-pass filters, such as Butterworth, Chebyshev, and Bessel filters. The choice of filter type will depend on the application and the desired characteristics.

3. Calculate the values of the components: The values of the components can be calculated using the filter design equations. For example, for a first-order high-pass filter, the cutoff frequency can be calculated using the equation:

fc = 1/(2*pi*R*C)

where fc is the cutoff frequency, R is the resistance, and C is the capacitance.

To design a high-pass filter with a half-power frequency between 159 and 161 kHz, you can choose a value for R, such as 10 kohms, and calculate the value of C using the above equation. For example, if you choose R = 10 kohms and fc = 160 kHz, the value of C would be:

C = 1/(2*pi*R*fc) = 9.95 nF

4. Build the filter: Once you have calculated the values of the components, you can build the filter using capacitors and resistors with the appropriate values. You can then test the filter and adjust the values of the components if necessary to achieve the desired frequency response.

Learn more about capacitors and resistors: https://brainly.com/question/31080064

#SPJ11