A 6.00L tank at 27.1°C is filled with 9.72g of sulfur tetrafluoride gas and 5.05g of carbon dioxide gas. You can assume both gases behave as ideal gases under these conditions.Calculate the partial pressure of each gas, and the total pressure in the tank.

Answers

Answer 1

The partial pressure of sulfur tetrafluoride gas is 8.78 kPa, the partial pressure of carbon dioxide gas is 24.9 kPa, and the total pressure in the tank is 33.7 kPa.

To solve this problem, we can use the ideal gas law: PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. We can rearrange this equation to solve for the pressure: P = nRT/V.

First, we need to calculate the number of moles of each gas. We can use the molar mass of each gas and the given mass to find the number of moles:

moles of SF₄ = 9.72 g / 108.1 g/mol = 0.0899 mol

moles of CO₂ = 5.05 g / 44.01 g/mol = 0.1148 mol

Next, we can plug in the values into the ideal gas law equation to find the partial pressures of each gas:

partial pressure of SF₄ = (0.0899 mol)(8.31 J/mol*K)(300.1 K) / 6.00 L = 8.78 kPa

partial pressure of CO₂ = (0.1148 mol)(8.31 J/mol*K)(300.1 K) / 6.00 L = 24.9 kPa

Finally, we can find the total pressure in the tank by adding the partial pressures:

total pressure = partial pressure of SF₄ + partial pressure of CO₂ = 8.78 kPa + 24.9 kPa = 33.7 kPa

To know more about partial pressure, refer here:

https://brainly.com/question/31214700#

#SPJ11


Related Questions

if the unit cell of copper (cu) has an edge length of approximately 362 pm and the radius of a copper atom is approximately 128 pm, what is the probable crystal structure of copper?

Answers

The probable crystal structure of copper is a simple cubic structure with a packing efficiency of approximately 63%.

To determine the probable crystal structure of copper, we need to calculate the packing efficiency of its atoms in the unit cell. The edge length of the unit cell is approximately 362 pm, which means that each side has a length of 362/2 = 181 pm. The volume of the unit cell can be calculated by taking the cube of the edge length, which gives us approximately 6.82 x 10^6 pm^3.
Next, we need to calculate the volume occupied by a single copper atom. The radius of a copper atom is approximately 128 pm, so its diameter is 2 x 128 = 256 pm. This means that the volume of a single copper atom is approximately 4/3 x pi x (128 pm)^3, which is approximately 4.31 x 10^6 pm^3.
To determine the packing efficiency of copper atoms in the unit cell, we can divide the volume occupied by the atoms by the total volume of the unit cell. Doing so gives us a packing efficiency of approximately 63%. This value is close to the packing efficiency of 68% for a simple cubic structure, which suggests that copper has a simple cubic crystal structure.
In summary, based on the given edge length of the unit cell and radius of a copper atom, the probable crystal structure of copper is a simple cubic structure with a packing efficiency of approximately 63%.

To know more about atom visit :

https://brainly.com/question/13518322

#SPJ11

use data from crc_std_thermodyn_substances and crc_std_thermodyn_aqueous-ions to calculate the requested properties for the following at 25 ∘c. (for caco3(s) use calcite)
ca(no3)2(aq)+na2co3(aq)->caco3(s)+2nano3(aq)
requested property (units):∆,s (j/k.mol)

Answers

The standard entropy change for the reaction at 25 ∘C is -85.0 J/K mol.


To calculate the requested property, we need to use the standard molar entropy values for each substance involved in the reaction. These values can be found in the crc_std_thermodyn_substances and crc_std_thermodyn_aqueous-ions databases.

The equation for the reaction is:

Ca(NO3)2(aq) + Na2CO3(aq) → CaCO3(s) + 2 NaNO3(aq)

To calculate the standard entropy change (∆S) for the reaction at 25 ∘C, we can use the following formula:

∆S = ΣnS(products) - ΣnS(reactants)

where n is the stoichiometric coefficient of each substance in the balanced chemical equation and S is the standard molar entropy of the substance.

From the databases, we can find the standard molar entropy values for each substance:

- Ca(NO3)2(aq): 203.0 J/K mol
- Na2CO3(aq): 174.0 J/K mol
- CaCO3(s) (calcite): 91.0 J/K mol
- NaNO3(aq): 116.0 J/K mol

Substituting these values into the formula, we get:

∆S = (1 mol x 91.0 J/K mol) + (2 mol x 116.0 J/K mol) - (1 mol x 203.0 J/K mol) - (1 mol x 174.0 J/K mol)
   = -85.0 J/K mol


The standard entropy change (∆S) for the reaction Ca(NO3)2(aq) + Na2CO3(aq) → CaCO3(s) + 2 NaNO3(aq) at 25 ∘C is -85.0 J/K mol.

To know more about entropy , visit;

https://brainly.com/question/419265

#SPJ11

Buffer is prepared by adding 1. 00 l of 1. 0 m hcl to 750 ml of 1. 5 m nahcoo. Whatis the ph of this buffer? [ka(hcooh) = 1. 7 × 10–4]

Answers

The pH of the buffer solution is approximately 10.29.

To calculate the pH of the buffer solution, we need to determine the concentrations of the acid and its conjugate base after mixing the HCl and NaHCOO solutions.

Given:

Volume of HCl solution (V1) = 1.00 L

Concentration of HCl solution (C1) = 1.0 M

Volume of NaHCOO solution (V2) = 750 mL = 0.75 L

Concentration of NaHCOO solution (C2) = 1.5 M

Ka of HCOOH (conjugate acid of HCOO-) = 1.7 × 10^(-4)

Step 1: Calculate the moles of acid and base:

Moles of acid (HCl) = C1 * V1

Moles of base (NaHCOO) = C2 * V2

Step 2: Calculate the total volume of the solution:

Total volume of the buffer solution = V1 + V2

Step 3: Calculate the final concentration of the acid and base:

Concentration of the acid (HCOOH) = Moles of acid / Total volume

Concentration of the base (HCOO-) = Moles of base / Total volume

Step 4: Calculate the pH of the buffer using the Henderson-Hasselbalch equation:

pH = pKa + log([concentration of base] / [concentration of acid])

Let's perform the calculations:

Step 1:

Moles of acid (HCl) = 1.0 M * 1.00 L = 1.00 mol

Moles of base (NaHCOO) = 1.5 M * 0.75 L = 1.125 mol

Step 2:

Total volume of the buffer solution = 1.00 L + 0.75 L = 1.75 L

Step 3:

Concentration of the acid (HCOOH) = 1.00 mol / 1.75 L ≈ 0.571 M

Concentration of the base (HCOO-) = 1.125 mol / 1.75 L ≈ 0.643 M

Step 4:

pH = pKa + log([0.643] / [0.571])

The pKa value given is for HCOOH (formic acid), not for HCOO-. To find the pKa value for HCOO-, we need to calculate the pKa using the pKa of HCOOH and the Ka-Kb relationship:

Ka * Kb = Kw (water dissociation constant)

Ka * (1e-14 / Ka) = 1.7e-4 * Kb

Kb = (1e-14) / (1.7e-4) ≈ 5.882e-11

Now, we can calculate the pKa for HCOO-:

pKa = -log(Ka) = -log(5.882e-11) ≈ 10.23

Using this pKa value, we can calculate the pH:

pH = 10.23 + log(0.643 / 0.571) ≈ 10.29

Therefore, the pH of the buffer solution is approximately 10.29.

Learn more about Buffer solution from the link given below.

https://brainly.com/question/30737303

#SPJ4

Use the half-reaction method to determine the net-ionic redox reaction between the permanganate ion (MnO4) and the bisulfite ion (HSO3) in test tube #3. Information above indicates Mn goes from +7 to +2 oxidation state and it happens in acidic medium. Sulfur goes from +4 to + 6 oxidation state in the oxidation reaction. Balance the two half reactions, multiply to have equal electrons transferred in each, and add to get the net ionic redox reaction. MnO4 (aq) + H(aq) + e → Mn" (aq) + H2O(1) (Hint: Do O first, then H, and see if atoms and charges balance) HSO3 (aq) + H2O(1) SO4 (aq) + H(aq) (Show Your Work)

Answers

The net ionic redox is: 2MnO4- (aq) + 5HSO3- (aq) + 6H+ (aq) → 2Mn2+ (aq) + 5SO4^2- (aq) + 3H2O (l).

How to determine the net-ionic redox reaction between the permanganate ion (MnO4-) and the bisulfite ion (HSO3-) in an acidic medium using the half-reaction method?

To balance the redox reaction between permanganate ion (MnO4-) and bisulfite ion (HSO3-) in an acidic medium, we need to follow these steps:

Step 1: Write the half-reactions for the oxidation and reduction processes.

Oxidation half-reaction:

MnO4- (aq) → Mn2+ (aq)

Reduction half-reaction:

HSO3- (aq) → SO4^2- (aq)

Step 2: Balance the atoms and charges in each half-reaction.

Oxidation half-reaction:

MnO4- (aq) + 8H+ (aq) + 5e- → Mn2+ (aq) + 4H2O (l)

Reduction half-reaction:

HSO3- (aq) + H2O (l) → SO4^2- (aq) + 2H+ (aq) + 2e-

Step 3: Multiply the half-reactions by appropriate coefficients to equalize the number of electrons transferred.

Oxidation half-reaction (multiplied by 2):

2MnO4- (aq) + 16H+ (aq) + 10e- → 2Mn2+ (aq) + 8H2O (l)

Reduction half-reaction (multiplied by 5):

5HSO3- (aq) + 5H2O (l) → 5SO4^2- (aq) + 10H+ (aq) + 10e-

Step 4: Add the balanced half-reactions together to obtain the net ionic redox reaction.

2MnO4- (aq) + 16H+ (aq) + 10e- + 5HSO3- (aq) + 5H2O (l) → 2Mn2+ (aq) + 8H2O (l) + 5SO4^2- (aq) + 10H+ (aq) + 10e-

Simplifying the equation and canceling out the spectator ions, we get:

2MnO4- (aq) + 5HSO3- (aq) + 6H+ (aq) → 2Mn2+ (aq) + 5SO4^2- (aq) + 3H2O (l)

Therefore, the net ionic redox reaction between permanganate ion (MnO4-) and bisulfite ion (HSO3-) in test tube #3, in an acidic medium, is:

2MnO4- (aq) + 5HSO3- (aq) + 6H+ (aq) → 2Mn2+ (aq) + 5SO4^2- (aq) + 3H2O (l).

Learn more about redox reactions.

brainly.com/question/13293425

#SPJ11

how to calculate lattice energy of lithium chloride from the following data: ionization energy of li

Answers

To calculate the lattice energy of lithium chloride (LiCl) using the given data, you can apply the Born-Haber cycle, which is a series of thermochemical processes that relate the lattice energy to other measurable quantities such as ionization energy and electron affinity.

The lattice energy (U) of LiCl can be calculated using the formula:

U = (Ionization energy of Li) + (Electron affinity of Cl) - (Energy change during the formation of LiCl)

Since you provided the ionization energy of lithium (Li), you'll need to look up the electron affinity of chlorine (Cl) and the energy change during the formation of LiCl (ΔHf°) in a reference or a database. Once you have these values, you can plug them into the formula and calculate the lattice energy of lithium chloride.

Know more about Ionization Energy here:

https://brainly.com/question/28385102

#SPJ11

Calculate the standard cell potential at 25 degrees C for the following cell reaction from standard free energies of formation (Appendix C).
2Al(s) + 3Cu
2
+
(aq) →
2Al
3
+
(aq) + 3Cu(s)

Answers

The standard cell potential at 25 degrees C for the given cell reaction is; -2.00 V.

To calculate the standard cell potential at 25 degrees C for the given cell reaction, we need to use the following equation;

E°cell = E°red, cathode - E°red, anode

where E°red, cathode is the standard reduction potential for the reduction half-reaction occurring at the cathode, and E°red, anode is the standard reduction potential for the reduction half-reaction occurring at the anode.

The half-reactions for the given cell reaction are;

Cathode; Cu²⁺(aq) + 2e⁻ → Cu(s)

Anode; Al³⁺(aq) + 3e⁻ → Al(s)

Using the standard free energies of formation (ΔG°f) for each species in Appendix C, we can calculate the standard reduction potentials (E°red) for each half-reaction using the following equation;

ΔG° = -nFE°red

where n is number of electrons transferred in the half-reaction, F is Faraday constant (96,485 C/mol), and E°red is standard reduction potential.

For the cathode half-reaction;

Cu²⁺(aq) + 2e⁻ → Cu(s)

ΔG°f(Cu²⁺(aq)) = -166.1 kJ/mol

ΔG°f(Cu(s)) = 0 kJ/mol

ΔG° = ΔG°f(Cu(s)) - ΔG°f(Cu²⁺(aq)) = 166.1 kJ/mol

n = 2 (since 2 electrons are transferred)

E°red,cathode = -ΔG°/(nF) = -0.34 V

For the anode half-reaction;

Al³⁺(aq) + 3e⁻ → Al(s)

ΔG°f(Al³⁺(aq)) = -524.2 kJ/mol

ΔG°f(Al(s)) = 0 kJ/mol

ΔG° = ΔG°f(Al(s)) - ΔG°f(Al³⁺(aq)) = 524.2 kJ/mol

n = 3 (3 electrons are transferred)

E°red,anode = -ΔG°/(nF) = 1.66 V

Therefore, the standard cell potential at 25 degrees C for the given cell reaction is;

E°cell = E°red,cathode - E°red,anode

E°cell = (-0.34 V) - (1.66 V)

E°cell = -2.00 V

The negative sign indicates that the cell reaction is not spontaneous under standard conditions.

To know more about standard cell potential here

https://brainly.com/question/14240930

#SPJ4

PQ-18. What is the pH of a 0.400 M sodium formate (NaCHO,) solution? K (HCHO,)-1.8x104 (A) 2.07 (B) 5.33 (C) 8.67 (D) 11.93

Answers

The pH of the 0.400 M sodium formate solution is approximately 1.90, which is closest to option (A) 2.07.

The condition for the separation of formic corrosive (HCHO₂) is:

HCHO₂ + H₂O ↔ H₃O⁺ + CHO²⁻

The balance steady articulation for this response is:

Ka = [ H₃O⁺][CHO²⁻]/[HCHO₂]

From the given data, we realize that the Ka of formic corrosive is 1.8 x 10^-4. We likewise know that sodium formate (NaCHO₂) is a salt of formic corrosive and it will separate totally in water to shape Na+ and CHO²⁻particles. The CHO²⁻ particle will respond with water to frame HCHO₂ and Goodness particles.

NaCHO₂(s) ↔ Na+(aq) + CHO²⁻(aq)

CHO²⁻(aq) + H2O(l) ↔ HCHO₂(aq) + Gracious (aq)

Since NaCHO₂ totally separates in water, we can expect that [CHO²⁻] = [NaCHO₂] = 0.4 M.

Let x be the centralization of  H₃O⁺ particles shaped in the response. Then, [OH-] = [tex]1.0 x 10^-14/x[/tex].

Utilizing the harmony consistent articulation, we can compose:

[tex]1.8 x 10^-4 = x^2/(0.4 - x)[/tex]

Since x << 0.4, we can surmised (0.4 - x) to be 0.4.

[tex]1.8 x 10^-4 = x^2/0.4[/tex]

[tex]x = sqrt(1.8 x 10^-4 x 0.4) = 0.0126 M[/tex]

pH = - log[H3O+] = - log(0.0126) = 1.90

Consequently, the pH of the 0.400 M sodium formate arrangement is roughly 1.90, which is nearest to choice (A) 2.07.

To learn more about PH, refer:

https://brainly.com/question/30892475

#SPJ1

calculate the enthalpy change for the following reaction given: dc-h= 414 kj/mol, dcl-cl=243 kj/mol, dc-cl=339 kj/mol, dh-cl=431 kj/mol. ch4 cl2 → ch3cl hcl

Answers

To calculate the enthalpy change for the given reaction: CH4 + Cl2 → CH3Cl + HCl, we will use the bond enthalpies provided (DC-H, DCl-Cl, DC-Cl, DH-Cl). We'll follow these steps:



1. Determine the bonds broken in the reactants.


2. Determine the bonds formed in the products.


3. Calculate the total enthalpy change for the reaction.

Step 1: Bonds broken in reactants:


- 1 DC-H bond in CH4 (414 kJ/mol)


- 1 DCl-Cl bond in Cl2 (243 kJ/mol)

Step 2: Bonds formed in products:


- 1 DC-Cl bond in CH3Cl (339 kJ/mol)


- 1 DH-Cl bond in HCl (431 kJ/mol)


Step 3: Calculate the total enthalpy change for the reaction:
Enthalpy change = (Σ bond enthalpies of bonds broken) - (Σ bond enthalpies of bonds formed)


Enthalpy change = (414 kJ/mol + 243 kJ/mol) - (339 kJ/mol + 431 kJ/mol)


Enthalpy change = (657 kJ/mol) - (770 kJ/mol)


Enthalpy change = -113 kJ/mol


The enthalpy change for the given reaction CH4 + Cl2 → CH3Cl + HCl is -113 kJ/mol.

To know more about CH4 + Cl2 → CH3Cl + HCl refer here

https://brainly.com/question/24141694#

#SPJ11

Use the following data to calculate the combined heat of hydration for the ions in sodium acetate (NaC2H3O2): Hlattice = 763 kJ/mol; Hsoln = 17.3 kJ/mol?
A. -746 kJ/mol
B. -780 kJ/mol
C. 746 kJ/mol
D. 780 kJ/mol

Answers

Therefore, the combined heat of hydration for the ions in sodium acetate is 780.3 kJ/mol. The correct answer is D.

To calculate the combined heat of hydration for the ions in sodium acetate, we need to use the following equation:
Hydration = ΔHsoln + ΔHlattice
where ΔHhydration is the combined heat of hydration, ΔHsoln is the heat of solution, and ΔHlattice is the lattice energy.
We are given that Hlattice = 763 kJ/mol and Hsoln = 17.3 kJ/mol, so we can substitute these values into the equation:
Hydration = 17.3 kJ/mol + 763 kJ/mol
Hydration = 780.3 kJ/mol

Therefore, the combined heat of hydration for the ions in sodium acetate is 780.3 kJ/mol. The correct answer is D.
To calculate the combined heat of hydration for the ions in sodium acetate (NaC2H3O2), we will use the following equation:
Hhydration = Hsoln - Hlattice
Plugging in the given values, we get:
Hhydration = 17.3 kJ/mol - 763 kJ/mol
Hhydration = -745.7 kJ/mol
Considering the answer choices, the closest option to our calculated value is:
A. -746 kJ/mol

To know more about hydration visit:-

https://brainly.com/question/11202174

#SPJ11

_K+_Cl2=_KCl someone please help

Answers

Answer:

2K+ CL2 = 2KCl

Explanation:

The equation is now balanced

A triply ionized beryllium ion, (a beryllium atom with three electrons removed), behaves very much like a hydrogen atom, except that the nuclear charge is four times as great.
What is the ground-level energy of Be3+?
What is the ionization energy of Be3+?
For the hydrogen atom, the wavelength of the photon emitted in the n = 2 to n = 1 transition is 122 . What is the wavelength of the photon emitted when a Be3+ ion undergoes this transition?

Answers

The wavelength of the photon emitted when a Be3+ ion undergoes the n = 2 to n = 1 transition is 7.53 x 10^-8 m.

The ground-level energy of [tex]Be_3+[/tex] can be calculated using the formula:

[tex]E = - (Z^2 * R_H) / n^2[/tex]

Plugging in the values gives:

[tex]E = - (4^2 * 13.6 eV) / 1^2 = -217.6 eV[/tex]

The ionization energy of [tex]Be_3+[/tex] is the energy required to remove an electron from the ion. Since Be3+ has only one electron, its ionization energy is simply equal to its ground-level energy, or 217.6 eV.

The wavelength of the photon emitted when a  [tex]Be_3+[/tex]  ion undergoes the n = 2 to n = 1 transition can be calculated using the formula:

ΔE = hc/λ

Plugging in the values gives:

ΔE = [tex](4^2 - 1^2) * 13.6 eV = 170.8 eV[/tex]

λ = hc/ΔE[tex]= (6.626 * 10^{-34} J s) * (2.998 * 10^8 m/s) / (170.8 eV * 1.602 * 10^{-19} J/eV) = 7.53 * 10^-8 m[/tex]

To know more about wavelength, here

brainly.com/question/31143857

#SPJ4

What is the strongest type of intermolecular force present in CH3(CH2)4OH?
dispersion
ion-dipole
ionic bonding
hydrogen bonding
dipole-dipole

Answers

The strongest type of intermolecular force present in CH3(CH2)4OH is hydrogen bonding.

This is due to the presence of an OH group, which creates a strong attraction between the hydrogen atom and the highly electronegative oxygen atom. Hydrogen bonding is the strongest intermolecular force among the options provided, which include dispersion, ion-dipole, ionic bonding, and dipole-dipole interactions.

A hydrogen bond is a type of dipole-dipole interaction that occurs when a hydrogen atom is bonded to a highly electronegative atom such as nitrogen, oxygen, or fluorine. In CH3(CH2)4OH, the hydrogen atoms are bonded to the oxygen atom, which is highly electronegative. This creates a strong dipole-dipole interaction between neighboring molecules, resulting in a higher boiling point and greater intermolecular attraction.

To learn more about intermolecular forces visit:

brainly.com/question/9007693

#SPJ11

Separate the redox reaction into its component half-reactions. 02 +2 Mg — 2 Mgo Use the symbol e for an electron. oxidation half-reaction: 2Mg → 2Mg2+ + 4e Incorrect reduction half-reaction: 4e + O2 -> 202-

Answers

The redox reaction into its component half-reactions. The correct half-reactions are as follows: Oxidation half-reaction: 2Mg → 2Mg²⁺ + 4e⁻  .Reduction half-reaction: O₂ + 4e⁻ → 2O²⁻

Redox reactions are any chemical processes in which both oxidation and reduction take place together with the loss and gain of an electron.

Redox reactions come in four different flavours:

DisproportionalDecompositionDisplacementCombination

Chemical reactions known as redox reactions occur when the oxidation states of the substrate change. Loss of electrons or a rise in an element's oxidation state are both considered to be oxidation. Gaining electrons or lowering the oxidation state of an element or its constituent atoms are both examples of reduction. As a result, oxidising agent is reduced while reducing agent is oxidised in a redox process.

Learn more about Redox reactions here

https://brainly.com/question/2671074

#SPJ11

calculate the concentration of freefe2 (aq) at equilibrium after 0.10 mol fe(no3)2 is added to 1.00 l of 3.00 mnacn(aq) at 25 °c given that the kf of fe(cn)64–is 1.5×1035.

Answers

The concentration of free Fe2+ at equilibrium is approximately 1.8 x 10^-17 M.

The formation of Fe(CN)64- can be represented by the equilibrium reaction:

Fe2+ + 4CN- ⇌ Fe(CN)64-

The equilibrium constant for this reaction can be expressed as Kf = [Fe(CN)64-]/([Fe2+][CN-]^4).

Initially, there is no Fe(CN)64- in solution, so [Fe(CN)64-] = 0 M. Let x be the concentration of free Fe2+ that reacts with CN- ions to form Fe(CN)64-. Then the equilibrium concentration of Fe(CN)64- will be [Fe(CN)64-] = x.

The concentration of CN- at equilibrium can be calculated using the stoichiometry of the reaction: 4 mol CN- are consumed for every 1 mol Fe2+. Thus, [CN-] = 4x.

Substituting these expressions into the equilibrium constant equation and solving for x, we get:

Kf = x/(3.00 - x)(4x)^4

Rearranging and solving the resulting quintic equation gives x ≈ 1.8 x 10^-17 M. This is the concentration of free Fe2+ at equilibrium.

Learn more about equilibrium here :

https://brainly.com/question/30694482

#SPJ11

draw the structure of this metabolic intermediate. please draw the intermediate in its ionized form.

Answers

Sure, I can definitely help you with that! In terms of the structure of this metabolic intermediate, it would be helpful to know which specific intermediate you are referring to, as there are many different metabolic pathways and intermediates involved in metabolism.

However, assuming that you are referring to a general metabolic intermediate, it would likely be a molecule that is involved in multiple metabolic pathways and serves as a sort of "middleman" between different stages of metabolism.
As for drawing the intermediate in its ionized form, it would depend on the specific intermediate in question and the conditions under which it is ionized. Generally speaking, when a molecule is ionized, it gains or loses one or more electrons, resulting in a net positive or negative charge. This can affect the structure of the molecule, particularly the distribution of electrons around the atoms involved.
Without more information about the specific intermediate and the conditions under which it is ionized, it is difficult to provide a specific drawing. However, I hope this general information about the structure and ionization of metabolic intermediates has been helpful!

Learn more about pathways here:

https://brainly.com/question/14342666

#SPJ11

A hydrochloric acid solution is standardized by titrating against solid sodium carbonate. The equation is :2HCl(aq) + Na2CO3(s) →2 NaCl(aq) + H2O(l) + CO2(g).If 23.4 mL of the solution is added from the buret to neutralize 0.157 g Na 2CO 3 in the flask, what is the molarity of the HCl solution?a. 0.0316 Mb. 0.0633 Mc. 7.90 Md. 0.253 Me. 0.127 M

Answers

According to the statement, 0.127 M  is the molarity of the HCl solution.

To calculate the molarity of the HCl solution, we first need to find the number of moles of Na2CO3 used in the titration.
Using the formula mass of Na2CO3 (105.99 g/mol), we can convert the given mass of 0.157 g to moles:
0.157 g Na2CO3 x (1 mol Na2CO3 / 105.99 g Na2CO3) = 0.00148 mol Na2CO3
From the balanced chemical equation, we can see that 2 moles of HCl react with 1 mole of Na2CO3. Therefore, the number of moles of HCl used in the titration is:
0.00148 mol Na2CO3 x (2 mol HCl / 1 mol Na2CO3) = 0.00296 mol HCl
Finally, we can calculate the molarity of the HCl solution by dividing the number of moles of HCl by the volume of HCl solution used (23.4 mL = 0.0234 L):
Molarity = moles of HCl / volume of HCl solution
Molarity = 0.00296 mol / 0.0234 L = 0.126 M
Therefore, the correct answer is e. 0.127 M.

To know more about hydrochloric acid visit:

brainly.com/question/15102013

#SPJ11

Select the best reaction sequence to make the following ketone. CH_3CCH_2CH_2CH_2CH_2CH_3 propane, NaNH_2 acetylene, NaNH_2 l-broniubutanr l-bromopcntanr H_2O, Hg^2+, H_2S04 H_2O, Hg2+. H_2S04 1-hexyne, NaNH_2 bromontcthane H_20, Hg2+ H_2S0 1-pentyne, NaNH_2 broniocthane H_20. Hg2+ H_2S04

Answers

The answer to the question is that the best reaction sequence to make the following ketone from CH3CCH2CH2CH2CH2CH3 propane is 1-pentyne, NaNH2, bromoethane, H2O, Hg2+, H2SO4.

The given propane needs to be converted into the desired ketone, which requires the addition of a carbonyl group to the molecule. This can be achieved through a series of reactions involving acetylene, l-broniuobutanr, 1-hexyne, and 1-pentyne. Out of these, the best reaction sequence is the one involving 1-pentyne, as it yields the desired ketone with high selectivity.

The reaction sequence involving 1-pentyne can be explained as follows. First, NaNH2 is used to deprotonate the terminal alkyne of 1-pentyne to form a sodium acetylide. This is followed by the addition of bromoethane to the acetylide, which results in the formation of an alkylated acetylene.

Next, H2O, Hg2+, and H2SO4 are added to the reaction mixture to carry out a hydration reaction, which results in the formation of an enol. The enol then undergoes tautomerization to form the desired ketone.

Overall, the reaction sequence involving 1-pentyne, NaNH2, bromoethane, H2O, Hg2+, and H2SO4 is the best choice for making the desired ketone from CH3CCH2CH2CH2CH2CH3 propane.

To learn more about ketones visit:

brainly.com/question/4439718

#SPJ11

calculate delta g for an electrochemical cell reaction that occurs under basic aques condittitons based on the following two half-reactions for which the standard reduction potentials are given. Use the smallest whole-number coefficients possible when balancing the overall reaction. Cd(OH)2 + 2e- ---> Cd + 2OH- -0.824VNiO(OH) + H2O + e- ---> Ni(OH)2 + OH- +1.32V

Answers

The ΔG for the electrochemical cell reaction under basic aqueous conditions is approximately -414,652 J/mol.

To calculate the ΔG for the electrochemical cell reaction under basic aqueous conditions, first balance the overall redox reaction using the half-reactions provided.
Oxidation half-reaction (multiply by 2 to balance electrons):
2[Cd(OH)2 + 2e- → Cd + 2OH-]; E° = -0.824V
Reduction half-reaction:
NiO(OH) + H2O + e- → Ni(OH)2 + OH-; E° = +1.32V
Balanced redox reaction:
2Cd(OH)2 + NiO(OH) + H2O → 2Cd + Ni(OH)2 + 5OH-
Now, calculate the cell potential E°cell by subtracting the oxidation potential from the reduction potential:
E°cell = E°red - E°ox = (+1.32V) - (-0.824V) = +2.144V
Next, calculate ΔG using the Nernst equation:
ΔG = -nFE°cell
n = number of electrons transferred (in this case, n=2)
F = Faraday constant (96,485 C/mol)
ΔG = -(2)(96,485 C/mol)(+2.144V) = -414,652 J/mol
To know more about electrochemical cell visit:

brainly.com/question/30266719

#SPJ11

The triprotic acid H3A has ionization constants of Ka1 = 5.2× 10–2, Ka2 = 7.2× 10–7, and Ka3 = 1.8× 10–11. Calculate the following values for a 0.0780 M solution of NaH2A.(B) Calculate the following values for a 0.0780 M solution of Na2HA.

Answers

For a 0.0780 M solution of NaH₂A, the concentrations of the different forms of the triprotic acid can be calculated using the ionization constants Ka1, Ka2, and Ka3. The values obtained are [H3A] = 0.0211 M, [H2A-] = 5.20 × [tex]10^{-6}[/tex] M, and [HA2-] = 7.20 × [tex]10^{-10}[/tex]M.

How are the concentrations  of solutions are determined?

In a 0.0780 M solution of NaH2A, the ionization constants (Ka1, Ka2, and Ka3) provide information about the extent of dissociation of the triprotic acid. Using these values, we can calculate the concentrations of H3A, H2A-, and HA2- in the solution.

The first ionization constant, Ka1, represents the equilibrium between H3A and H2A-. Since the concentration of NaH2A is 0.0780 M, we can assume that the concentration of H3A is equal to the initial concentration of NaH2A. Therefore, [H3A] = 0.0780 M.

The second ionization constant, Ka2, represents the equilibrium between H2A- and HA2-. To calculate the concentration of H2A-, we need to consider the dissociation of H3A.

According to Ka1, only a small fraction of H3A will dissociate into H2A-. Thus, [H2A-] is approximately equal to Ka1 multiplied by the concentration of H3A. Substituting the values, [H2A-] = 5.20 ×[tex]10^{-6}[/tex] M.

The third ionization constant, Ka3, represents the equilibrium between HA2- and A3-. Since Ka3 is very small, we can assume that the dissociation of H2A- into HA2- is negligible. Therefore, [HA2-] is  approximately equal to the concentration of H2A-, which is 5.20 × [tex]10^{-6}[/tex]M.

therefore, for a 0.0780 M solution of NaH2A, the concentrations of H3A, H2A-, and HA2- are approximately 0.0780 M, 5.20 × [tex]10^{-6}[/tex]M, and 7.20 × [tex]10^{-10}[/tex] M, respectively.

Learn more about solution

brainly.com/question/15757469

#SPJ11

calculate the ph of the cathode compartment solution if the cell emf at 298 k is measured to be 0.670 v when [zn2 ]= 0.22 m and ph2= 0.96 atm

Answers

The pH of the cathode compartment solution is approximately 1.67.

The pH of the cathode compartment solution can be calculated using the Nernst equation, which relates the cell potential to the concentrations and activities of the reactants and products involved in the half-reactions.

In this case, the half-reaction at the cathode is:

2H+ + 2e- → [tex]H_2[/tex].

The standard reduction potential for this reaction is 0 V.

The actual potential is given as 0.670 V, with [[tex]Zn^2+[/tex]] = 0.22 M and [tex]pH_2[/tex] = 0.96 atm.

Using the Nernst equation, we can calculate the pH of the cathode compartment solution to be approximately 1.67.

This calculation takes into account the concentration of hydrogen ions, the partial pressure of hydrogen gas, and the temperature of the system.

For more such questions on pH, click on:

https://brainly.com/question/172153

#SPJ11

The pH of the cathode compartment solution, calculated using the Nernst equation with a cell potential of 0.670 V, [Zn²⁺] = 0.22 M, and pH₂ = 0.96 atm, is approximately 3.54.

Determine how to find the pH of the cathode compartment?

To calculate the pH of the cathode compartment solution, we can use the Nernst equation, which relates the cell potential to the concentrations of the species involved. The Nernst equation is given as:

E = E° - (RT/nF) * ln(Q)

Where:

E is the measured cell potential (0.670 V),

E° is the standard cell potential (dependent on the specific reaction),

R is the gas constant (8.314 J/(mol·K)),

T is the temperature in Kelvin (298 K),

n is the number of electrons transferred (depends on the specific reaction),

F is the Faraday constant (96485 C/mol),

ln is the natural logarithm,

and Q is the reaction quotient.

In this case, the reaction taking place at the cathode is the reduction of hydrogen ions (H⁺) to hydrogen gas (H₂). The reaction quotient, Q, can be expressed as [H₂]/[H⁺]², where [H₂] is the partial pressure of hydrogen gas and [H⁺] is the concentration of hydrogen ions.

Given the partial pressure of hydrogen gas (pH₂ = 0.96 atm) and the concentration of zinc ions ([Zn²⁺] = 0.22 M), we can determine the concentration of hydrogen ions ([H⁺]) using the ideal gas law: pH₂ = [H₂]RT.

Solving the Nernst equation with the known values, we can calculate the cell potential (E), which is related to the pH of the cathode compartment solution. By converting the cell potential to pH, we find that the pH of the cathode compartment solution is approximately 3.54.

Therefore, the pH of the cathode compartment solution is approximately 3.54, determined using the Nernst equation with a cell potential of 0.670 V, [Zn²⁺] = 0.22 M, and pH₂ = 0.96 atm.

To know more about Nernst equation, refer here:

https://brainly.com/question/31593791#

#SPJ4

what will be the 13c frequency of an nmr spectrometer that operates at 500 mhz for protons? enter your answer in the provided box.

Answers

So, the 13C frequency of the NMR spectrometer would be 125.8 MHz.

Nuclear Magnetic Resonance (NMR) spectroscopy is a powerful technique that is widely used in chemistry, biochemistry, and related fields for the study of molecular structure and dynamics. The technique is based on the magnetic properties of atomic nuclei, which are influenced by the surrounding chemical environment and can be detected as resonant signals in the radiofrequency (RF) range. The frequency of these signals depends on the strength of the magnetic field and the gyromagnetic ratio of the nucleus being studied.
In a typical NMR experiment, a sample is placed in a strong magnetic field and exposed to a series of RF pulses. The resonant signals emitted by the nuclei in the sample are detected by a spectrometer, which analyzes their frequency and intensity. The resulting spectrum provides information about the chemical composition and structure of the sample, as well as the interactions between different molecular components.
The frequency range used in NMR spectroscopy is typically in the range of tens to hundreds of MHz, depending on the type of nuclei being studied and the strength of the magnetic field. For example, proton NMR is commonly performed at frequencies between 300 and 900 MHz, while 13C NMR is typically performed at lower frequencies, around 100 MHz.
In summary, the frequency of an NMR spectrometer determines the range of nuclear resonances that can be detected and analyzed, and plays a crucial role in the sensitivity and resolution of the experiment. Understanding the relationship between the frequency, magnetic field strength, and gyromagnetic ratio of different nuclei is essential for designing and interpreting NMR experiments.

The 13C frequency of an NMR spectrometer that operates at 500 MHz for protons can be calculated using the formula:
Frequency of nucleus A

= (Frequency of nucleus B) x (gyromagnetic ratio of nucleus A / gyromagnetic ratio of nucleus B)
In this case, nucleus A is 13C and nucleus B is proton. The gyromagnetic ratio of proton is 1 and the gyromagnetic ratio of 13C is 0.2516.
Therefore, the 13C frequency can be calculated as:
Frequency of 13C

= (500 MHz) x (0.2516 / 1)

= 125.8 MHz
To know more about spectrometer visit:

https://brainly.com/question/31518908

#SPJ11

What do the symbols inside parentheses represent in the following chemical equation?
Sr(s) + 2H₂O(l) → Sr(OH)2(aq) + H₂(g)
Symbol
(s)
(1)
(aq)
(g)
Meaning

Answers

Below are the symbols and meaning:

(s) indicates that the substance is a solid.(l) indicates that the substance is a liquid.(aq) indicates that the substance is an aqueous solution, which means that it is dissolved in water.(g) indicates that the substance is a gas.

What is an aqueous solution?

An aqueous solution refers to a solution wherein water functions as the dissolving agent. It represents a harmonious amalgamation in which one or multiple substances, referred to as solutes, are intricately dissolved within water, which serves as the dissolving medium.

The remarkable attributes of water, including its polarity and capacity to form hydrogen bonds, render it an exceptional solvent for an extensive array of substances.

Learn about solid and liquid here https://brainly.com/question/752663

#SPJ1

the analysis of an unknown organic compound revealed a percent composition of 26.09% carbon, 4.35% hydrogen, and 69.56% oxygen. what is the empirical formula for this compound?

Answers

The empirical formula for the compound is therefore C₂H₄O, which means that it contains two carbon atoms, four hydrogen atoms, and six oxygen atoms.  

The empirical formula for an organic compound is the simplest whole-number ratio of the numbers of atoms of each element in the compound.

To find the empirical formula for an unknown compound with a percent composition of 26.09% carbon, 4.35% hydrogen, and 69.56% oxygen, we can use the following equation:

Empirical formula = (atomic mass of carbon) / (number of carbon atoms) × (1/12) + (atomic mass of hydrogen) / (number of hydrogen atoms) × (1/2) + (atomic mass of oxygen) / (number of oxygen atoms)

First, we can use the atomic mass of carbon, which is 12.01 g/mol, to find the number of carbon atoms in the compound:

number of carbon atoms = (atomic mass of carbon) / (atomic mass of carbon/mol)

number of carbon atoms = 12.01 g/mol / 12 g/mol

number of carbon atoms = 1 g/mol

Next, we can use the number of carbon atoms and the percent composition of carbon to find the molar mass of the compound:

Molar mass = (number of atoms of an element) × (atomic mass of an element/mol)

Molar mass = (number of carbon atoms) × (12 g/mol)

Molar mass = 1 g/mol

We can use the molar mass and the percent composition of each element to find the number of moles of each element in the compound:

Number of moles of carbon = (molar mass of carbon) / (molar mass of carbon/mol)

Number of moles of carbon = 1 g/mol / 12 g/mol

Number of moles of carbon = 0.00833 mol

Number of moles of hydrogen = (molar mass of hydrogen) / (molar mass of hydrogen/mol)

Number of moles of hydrogen = 1 g/mol / 1 g/mol

Number of moles of hydrogen = 1 mol

Number of moles of oxygen = (molar mass of oxygen) / (molar mass of oxygen/mol)

Number of moles of oxygen = 16 g/mol / 16 g/mol

Number of moles of oxygen = 1 mol

We can use the number of moles of each element and the empirical formula to find the number of atoms of each element in the compound:

Number of atoms of carbon = number of moles of carbon / Avogadro's number

Number of atoms of carbon = 0.00833 mol / 6.022 x 10²³  atoms/mol

Number of atoms of carbon = 1.35 x 10²²atoms of carbon

Number of atoms of hydrogen = number of moles of hydrogen / Avogadro's number

Number of atoms of hydrogen = 1 mol / 6.022 x 10²³ atoms/mol

Number of atoms of hydrogen = 1.67 x 10²² atoms of hydrogen

Number of atoms of oxygen = number of moles of oxygen / Avogadro's number

Number of atoms of oxygen = 1 mol / 6.022 x 10²³ atoms/mol

Number of atoms of oxygen = 1.67 x 10²² atoms of oxygen

The empirical formula for the compound is therefore C₂H₄O, which means that it contains two carbon atoms, four hydrogen atoms, and six oxygen atoms.  

Learn more about empirical formula

https://brainly.com/question/32125056

#SPJ4

Sodium chloride (NaCl) has the rock salt crystal structure and a density of 2.17 g/cm3. The atomic weights of sodium and chlorine are 22.99 g/mol and 35.45 g/mol, respectively.
(a) Determine the unit cell edge length.
(b) Determine the unit cell edge length from the radii in the table below assuming that the Na+ and Cl- ions just touch each other along the edges.

Answers

(a) The unit cell edge length is 5.64 x 10⁻⁸ cm and; (b) The unit cell edge length from the radii in the table assuming that the Na+ and Cl- ions just touch each other along the edges is 5.66 x 10⁻⁸ cm.

(a) To determine the unit cell edge length, we first need to know the formula for the rock salt crystal structure. The rock salt crystal structure is a face-centered cubic lattice with sodium ions (Na⁺) occupying the face-centered positions and chloride ions (Cl⁻) occupying the body-centered positions.

In this crystal structure, the unit cell contains one Na⁺ ion and one Cl⁻ ion. The edge length of the unit cell can be calculated using the following formula:

density = (mass of unit cell)/(volume of unit cell) = (molar mass of NaCl)/(Avogadro's number x volume of unit cell)

where Avogadro's number is 6.022 x 10²³ and the molar mass of NaCl is the sum of the atomic weights of Na and Cl.

Substituting the given values, we get:

2.17 g/cm³ = (22.99 g/mol + 35.45 g/mol)/(6.022 x 10²³ x volume of unit cell)

Solving for the volume of the unit cell, we get:

volume of unit cell = (22.99 g/mol + 35.45 g/mol)/(6.022 x 10²³ x 2.17 g/cm³) = 2.82 x 10⁻²³ cm³

The edge length of the unit cell can be calculated using the formula:

volume of unit cell = (edge length)³

Substituting the value of the volume of the unit cell, we get:

2.82 x 10⁻²³ cm³ = (edge length)³

Taking the cube root of both sides, we get:

edge length = 5.64 x 10⁻⁸ cm

Therefore, the unit cell edge length is 5.64 x 10⁻⁸ cm.

(b) The table below gives the ionic radii for Na⁺ and Cl⁻ ions:

Ion Ionic radius (pm)

Na⁺ 102

Cl⁻ 181

Assuming that the Na⁺ and Cl⁻ ions just touch each other along the edges, the unit cell edge length can be calculated as follows:

unit cell edge length = 2 x (ionic radius of Na⁺ + ionic radius of Cl⁻)

Substituting the given values, we get:

unit cell edge length = 2 x (102 pm + 181 pm) = 566 pm

Converting picometers to centimeters, we get:

unit cell edge length = 5.66 x 10⁻⁸ cm

Therefore, the unit cell edge length from the radii in the table is 5.66 x 10⁻⁸ cm.

To know more about unit cell follow the link:

https://brainly.com/question/31627817

#SPJ4

state whether the data is continous or discrete The durations of a chemical reaction comma repeated several times Choose the correct answer below. A. The data are continuous because the data can take on any value in an interval . B. The data are continuous because the data can only take on specific values . C. The data are discrete because the data can only take on specific values . D. The data are discrete because the data can take on any value in an interval.

Answers

The data in this case refers to the durations of a chemical reaction that are repeated several times is A. The data are continuous because the data can take on any value in an interval.

In order to determine whether the data is continuous or discrete, we need to consider the nature of the values that the data can take on. Continuous data is data that can take on any value within a certain range or interval. On the other hand, discrete data is data that can only take on specific values.

In this case, the durations of the chemical reaction can take on any value within a certain range of time. For example, the duration of the reaction could be 3.2 seconds, 3.25 seconds, or 3.27 seconds, among others. Therefore, the data is continuous. In summary,  the correct answer, therefore, is A. The data are continuous because the data can take on any value in an interval. The durations of a chemical reaction, repeated several times, are an example of continuous data because the values can take on any value within a certain range or interval.

To learn more about continuous data here:

https://brainly.com/question/30640857

#SPJ11

Calculate the value of Ecell at 25 °C for the following reaction and conditions:
Correct answer is 2.36 V.Al(s) | Al3+(aq) || I2(s) | I–(aq) | Pt(s) and [Al3+] = 0.150 M and [I–] = 0.00250 M:
E°cell = 2.19 V

Answers

The Nernst equation is used to calculate the value of E°cell at 25 °C for the given reaction and conditions is 2.36 V.

Nernst equation is given by:

Ecell = E°cell - (RT/nF) ln(Q)

where E°cell is the standard cell potential, R is the gas constant, T is the temperature, n is the number of electrons transferred in the reaction, F is the Faraday constant, and Q is the reaction quotient.

In this case, the reaction quotient can be calculated as follows:

Q = [Al3+]/[I-]^2

Substituting the given values, we get:

Q = (0.150)/(0.00250)^2 = 24000

Substituting all the given values in the Nernst equation, we get:

Ecell = 2.19 - [(8.314298)/(296485)]*ln(24000)

Ecell = 2.36 V

Therefore, the value of Ecell at 25 °C for the given reaction and conditions is 2.36 V. This indicates that the reaction is spontaneous under these conditions.

Know more about Nernst equation here:

https://brainly.com/question/13043546

#SPJ11

calculate the hydronium ion concentration and the ph of the solution that results when 75.0 ml of 0.405 m ch3cooh is mixed with 104 ml of 0.210 m naoh. acetic acid's ka is 1.70 ✕ 10−5

Answers

the hydronium ion concentration is 0.0064 mol/L and the ph of the solution is 2.19 that results when 75.0 ml of 0.405 m ch3cooh is mixed with 104 ml of 0.210 m naoh. acetic acid's ka is 1.70 ✕ 10−5

First, we need to determine the amount of acid and base that reacts with each other. To do this, we use the following equation:

n(CH3COOH) = C(CH3COOH) x V(CH3COOH) = (0.405 mol/L) x (0.075 L) = 0.0304 mol

n(NAOH) = C(NAOH) x V(NAOH) = (0.210 mol/L) x (0.104 L) = 0.0218 mol

Since the acid and base react in a 1:1 ratio, we see that the limiting reagent is the NaOH. Therefore, all of the NaOH will react, leaving us with 0.0086 mol of CH3COOH.

Next, we need to calculate the concentration of the remaining CH3COOH:

[CH3COOH] = n(CH3COOH) / V(total) = (0.0086 mol) / (0.179 L) = 0.048 mol/L

Using the Ka expression for acetic acid, we can solve for the hydronium ion concentration:

Ka = [H3O+][CH3COO-] / [CH3COOH]

[H3O+] = sqrt(Ka x [CH3COOH] / [CH3COO-]) = sqrt((1.70E-5)(0.048)/(0.0218)) = 0.0064 mol/L

Finally, we can calculate the pH:

pH = -log[H3O+] = -log(0.0064) = 2.19

For more such questions on hydronium ion concentration:

https://brainly.com/question/13387755

#SPJ11

The hydronium ion concentration is 0.0237 M and the pH is 1.63. This is found by calculating the moles of acid and base, determining the limiting reactant, and then using the balanced equation to calculate the excess reactant. The excess OH- concentration is used to calculate the hydronium ion concentration and pH using the Kw expression and the definition of p H.

To calculate the hydronium ion concentration and pH, we first determine the moles of acid and base using their respective concentrations and volumes. Then, we determine the limiting reactant, which is acetic acid in this case. The balanced equation for the reaction is CH3COOH + OH- → CH3COO- + H2O. We can use the stoichiometry of the balanced equation to determine the excess OH- concentration. The concentration of hydronium ions can be calculated using the Kw expression, and the pH is found using the definition of pH. The resulting values indicate that the solution is acidic.

Learn more about hydronium ion here;

https://brainly.com/question/13387755

#SPJ11

chemical is typically classified as a sensitizer if it causes an allergic reaction after exposure. Based on the SDS information provided, which of the following chemicals used in this lab is most likely classified as a sensitizer ethanol potassium hydroxide benzaldehyde dibenzalacetone

Answers

Based on the SDS information provided, potassium hydroxide is most likely classified as a sensitizer. Potassium hydroxide is a strong base that is used in many chemical reactions.

It can cause skin irritation and allergic reactions in some people, particularly those who have a history of skin sensitization. The SDS information should include a warning about the potential for skin sensitization and advise users to avoid contact with the skin or eyes and to wear appropriate protective clothing.

Ethanol and dibenzalacetone are not typically classified as sensitizers, but it is always important to read and follow the safety instructions and warnings provided with any chemical to ensure safe handling and use.  

Learn more about potassium hydroxide visit: brainly.com/question/28330489

#SPJ4

The metabolic pathways of organic compounds have often been delineated by using a radioactively labeled substrate and following the fate of the label.
(a) How can you determine whether glucose added to a suspension of isolated mitochondria is metabolized to co2 and h2o?
(b) Suppose you add a brief pulse of [3-14c] pyruvate (labeled in the methyl position) to Ehe mitochondria. After one turn of the citric acid cycle, what is the location of the14c in the oxaloacetate? Explain by tracing the 14 C label through the pathway. How many turns of the cycle are required to release all the [3-14c]pyruvate as co2?

Answers

The citric acid cycle (CAC)—also known as the Krebs cycle, Szent-Györgyi-Krebs cycle, or the TCA cycle (tricarboxylic acid cycle)[1][2]—is a series of chemical reactions to release stored energy through the oxidation of acetyl-CoA derived from carbohydrates, fats, and proteins.

The Krebs cycle is used by organisms that respire (as opposed to organisms that ferment) to generate energy, either by anaerobic respiration or aerobic respiration the cycle provides precursors of certain amino acids, as well as the reducing agent NADH, that are used in numerous other reactions. Its central importance to many biochemical pathways suggests that it was one of the earliest components of metabolism.[3][4] Even though it is branded as a 'cycle', it is not necessary for metabolites to follow only one specific route; at least three alternative segments of the citric acid cycle have been recognized.

Learn more about biochemical here:

https://brainly.com/question/939606

#SPJ11

If 36. 7 mL of 3M MgCl2 is used what is the mass of Mg(OH)2 produced?

Answers

The mass of Mg(OH)2 produced from 36.7 mL of 3M MgCl2 can be calculated using stoichiometry and the balanced chemical equation for the reaction.

The balanced chemical equation for the reaction between MgCl2 and NaOH is MgCl2 + 2NaOH → Mg(OH)2 + 2NaCl. From the equation, we can see that one mole of MgCl2 reacts with two moles of NaOH to produce one mole of Mg(OH)2.

To calculate the mass of Mg(OH)2 produced, we need to use stoichiometry and the given amount of MgCl2 and its concentration. We first convert the volume of MgCl2 to moles by multiplying it with its concentration:

36.7 mL * (3 moles/L) * (1 L/1000 mL) = 0.11 moles MgCl2

Since one mole of MgCl2 produces one mole of Mg(OH)2, the number of moles of Mg(OH)2 produced will also be 0.11 moles.

The molar mass of Mg(OH)2 is 58.33 g/mole, so the mass of Mg(OH)2 produced can be calculated by multiplying the number of moles by its molar mass:

0.11 moles * 58.33 g/mole = 6.42 g Mg(OH)2

Therefore, the mass of Mg(OH)2 produced from 36.7 mL of 3M MgCl2 is 6.42 g.

Learn more about chemical equation here.

https://brainly.com/questions/28792948

#SPJ11

Other Questions
which of the following is true about location-allocation analysis? cannibalization from a new brand is more threatening when the new brand's unit margin is higher than the firm's margin from its existing brands. true or false silver metal reacts with nitric acid according to the equation: 3ag(s) 4hno3(aq) 3agno3 (aq) no(g) 2h2o(l) what volume of 1.15 m hno3(aq) is required to react with 0.784 g of silver? according to the irr analysis, which investment is most profitable over the life of the investment? multiple choice 1 investment 2 investment 1 investment 3 2. according to the irr analysis, which investment is least profitable over the life of the investment? multiple choice 2 investment 3 investment 2 investment 1 3. what is the amount of net cash flows (not discounted) over the life of investment 2? multiple choice 3 $80,000 $77,000 $90,000 $110,000 4. if the cost of capital is 8%, will a company that that would pay $100,000 investment in equipment in year 0, and then receives $21,000 per year each of the next eight years (but no salvage value) make the investment? multiple choice 4 no yes 5. what would the net cash flows (not discounted) for a company that makes a $100,000 investment in year 0, and then receives $21,000 per year each of the next eight years? multiple choice 5 $168,000 $68,000 $268,000 $100,000 jureks brother is 6 years older than him .Together they are 22 years old ,how old are the brothers.Write down the correct equation? rank the following noncovalent intermolecular interactions from strongest (1) to weakest (3). A. dispersion forces. B. dipole-dipole attraction. C. hydrogen bonds. D. ionic interactions to discover causal relationships, traditionally scientific research tests connections between _____________. complete the square to write the equation of the sphere in standard form. x2 y2 z2 7x - 2y 14z 20 = 0 Find the center and radius. center (x, y, z) = () radius FILL IN THE BLANK.An _______ method gets the value of a data attribute but does not change it The response of Americans to new immigrants in the early twenty-first century was ______. true or false? unlike the unemployment rate, the natural rate of unemployment cannot change over time, when the president hosts the german chancellor for a fancy state dinner, they are playing which of the following presidential roles? calculate the taylor polynomials 2() and 3() centered at = for ()=12sin(), =2. Cart a has a mass 7 kg is traveling at 8 m/s. another cart b has mass 9 kg and is stopped. the two carts collide and stick together. what is the velocity of the two carts after the collision? amie was born in 1991. her mother is a college professor, and her father is an attorney. she's not sure what she wants to do when she grows up, but she knows she will go to college and embark on a career of her own. she was amazed when her grandmother told her that women really couldn't do that when she was young. if a woman did work, choices were usually limited to becoming a teacher, a secretary, or a nurse. her grandmother told her that she was a secretary, but after she started having children, she left the workforce and stayed home to raise her children, which was common for most women at that time. that concept was totally foreign to amie. to which generation does she belong?most have refused government support and are going through a hermitization process. they don't trust anyone under 60. Cystic fibrosis is a rare recessive disease. Jane and John went to see a genetic counselor because Janes sister and Johns nephew (his brothers son) are affected with cystic fibrosis. What is the probability that their first child will be a carrier of the cystic fibrosis mutation? Write 2 complete paragraphs!!1) Ponyboy says, It isnt fair a few times in this chapter. What do you think he is referring to? What is not fair to Ponyboy? Do you agree or disagree?2) At the end of the chapter, how does the author foreshadow that bad things are to come? Predict what might happen in the next chapter! let a and b be events such that p[a]=0.7 and p[b]=0.9. calculate the largest possible value of p[ab]p[ab]. In his "Inaugural Address," Kennedy contrasts ideas to develop the argument that the choices governments and citizens make will determine their fate. Select Yes or No to indicate which details demonstrate Kennedys use of contrast. (Picture Below) What is the relation between intrinsic carrier concentration and energy gap?