A stone is thrown vertically upward with an initial speed of 18.1 m/s. Neglect air resistance. The speed of the stone when it is 8.26 m higher is:

As a result, the force's effort is at its greatest when there is no angle between its direction and displacement, hence option A is correct.

According to physics, a force is an effect that has the power to change an object's motion.

A force can cause a massed item to accelerate or modify its velocity. A push or a pull is a straightforward method to explain forces. Since a force has both magnitude and direction, it is a vector quantity.

Therefore, work is therefore at its greatest when the angle between force and displacement is 0 °.

Learn more about work done, here:

https://brainly.com/question/11870590

#SPJ1

Answer:    A. when the angle between the force and displacement is 0 degrees.

Explanation:

Edmentum

The magnitude of the force acting on each object is equal to 3.87 x 10-8 N.

The magnitude of the force acting on each object can be calculated using Coulomb's law, which states that the electrostatic force (F) between two point objects with charges (q1 and q2) is equal to the product of the electric constant (k) and the product of the charges divided by the square of the distance (r) between them.

Thus, the formula for calculating the force is F = k(q1q2)/r2. In this case, the charges are both -42 nC, and the distance is 0.46 m. The electric constant is 8.99 x 109 Nm2/C2. Thus, the magnitude of the force acting on each object is equal to 3.87 x 10-8 N

Learn more about forces:

https://brainly.com/question/25239010

#SPJ2

Hydroelectric power accounts for between 16 and 17 percent of global electricity production, making it one of the most significant renewable energy sources.

In 2016, hydropower contributed more than twice as much to the grid as the next largest renewable energy source, solar. Hydropower can provide many valuable services to the power grid beyond just energy generation. These include frequency regulation, voltage support, contingency reserves, load following, and black start service, all of which contribute to the reliability and safety of the power system. Hydropower's role in grid-scale energy storage, balancing services for other intermittent renewables like wind and solar power, and water management services by reservoirs are growing.

Want to know more about hydroelectric power visit the link which is given below;

https://brainly.com/question/15228003

#SPJ4

The rate at which work is completed is indicated by the power word, hence option b is correct. Power, which can be defined as the amount of work done W.

Is the time rate at which the job is completed or energy is given. Energy transferred, expressed as W/t or energy transferred against the time interval t. Work (or energy) per unit time, foot-pounds per minute, joules per second (or watts), and ergs per second are all ways to express power. Work is defined as involving both force applied to the body and displacement of the body. Consider a block that is resting on a horizontal, frictionless floor. A consistent force is acting on this block.

Learn more about force here

https://brainly.com/question/13191643

#SPJ4

Answer:  B.) power

Explanation: Get dem hearts up:)

Magnetic Resonance Imaging is a technique for producing precise pictures of the brain that uses radio waves and the magnetic fields of the body.

A magnetic field and radio waves produced by a computer are used in the medical imaging procedure known as magnetic resonance imaging (MRI), which produces precise pictures of your body's organs and tissues.

The noninvasive medical imaging procedure known as magnetic resonance imaging, or MRI, creates precise pictures of virtually every internal bodily structure, including the organs, bones, muscles, and blood arteries. A sizable magnet and radio waves are used in MRI scanners to produce pictures of the human body.

To know more about Magnetic Resonance visit :

brainly.com/question/20371187

#SPJ4

On the microscope slide, a specimen will appear upside-down and facing left while it is actually right-side up and facing right.

The orientation of the specimen image is reversed when viewed via a microscope compared to the orientation of the actual specimen. As a result, when viewed under a microscope, the specimen will appear to be upside-down and backwards.

Coarse Adjustment Knob: To concentrate the specimen, the coarse adjustment knob, which is placed on the microscope's arm, raises and lowers the stage. With just a partial turn of the adjustment knob, the gearing system creates a significant vertical movement of the stage.

Condenser-Objective lens-Body tube-Eyepiece is the proper order for the flow of light in a compound microscope.

Use two hands at all times when moving your microscope. Lift the scope while encircling the arm with one hand.

To learn more about microscope refer to:

https://brainly.com/question/9255183

#SPJ4

A simulation because it replicates a molecule's internal operation.

Heat is the primary source of particle motion on Earth. The temperature of any substance is correlated with the energy of the atoms and molecules that comprise it. Energy is conserved, thus if one particle loses energy, another one acquires it.

Translational motion is the term used to describe how an atom may travel from one place in space to another. Additionally, molecules composed of several atoms can vibrate because of chemical bonds, which cause the atoms to move about their equilibrium position like springs.

To know more about simulation visit:

brainly.com/question/25583986

#SPJ4

Important Formulas:

[tex]v=\dfrac{d}{t}[/tex]

velocity(measured in m/s) = distance(measured in meters) / time(measured in seconds)

__________________________________________________________

Given:

[tex]d=15m[/tex]

[tex]t=3s[/tex]

[tex]v=?[/tex]

__________________________________________________________

Finding velocity:

[tex]v=\dfrac{d}{t}[/tex]

[tex]v=\dfrac{15}{3}[/tex]

__________________________________________________________

[tex]\fbox{v = 5 m/s}[/tex]

The time it takes the sound wave to travel to and fro through 2000 m is 11.66 seconds.

A sound wave is the pattern of disturbance caused by the movement of energy traveling through a medium.

To calculate the time it takes the sound wave to travel, we use the formula below

Formula:

Where:

From the question,

Substitute these values into equation 1

The time it takes is 11.66 seconds.

Learn more about sound wave here: https://brainly.com/question/29402395

#SPJ1

Dynamic flexibility example is a swimmer may circle their arms before getting into the water.

What is dynamics flexibility?

To learn more about dynamics flexibility refer to:

https://brainly.com/question/15740954

#SPJ4

After the original tube containing the mercury is replaced with a tube having twice the diameter of the original tube the height of the mercury column at one atmosphere of pressure is 760 mm.

The force delivered perpendicularly to an object's surface per unit area across which this force is dispersed is known as pressure. In comparison to the surrounding pressure, gauge pressure represents the pressure. Pressure is expressed to use a multitude of units.

The formula for calculating pressures is P = F / A, or force per unit of the surface area. The Si system for measuring the pressure is the pascal, and the sign for pressure in physical science is p. (symbol: Pa).

To know more about pressure visit:

https://brainly.com/question/15079200

#SPJ4

The plates become sufficiently stable by convection. The almost liquid rocks are moved by the convection currents' growing heat, hence option C is correct.

Rocks flex under the pressure of convection until they entirely fracture. Radiation decay in the core causes convection currents, which are produced by heat rising and sinking inside the mantle.

In convection currents, the plates are moved. The separation of plates occurs when convection currents split close to the Earth's crust.

Therefore, the convergence of convection currents causes plates to move in the same direction.

Learn more about tectonic plates, here:

https://brainly.com/question/18612190

#SPJ1

Steel is an alloy of iron and carbon. One of the main reasons steel is used more widely than iron is that it’s stronger than iron.

Steel, unlike other forms of iron, is strengthened by the addition of carbon, making it more resistant to fracture. Additional components are possible or even expected. To prevent corrosion and oxidation, stainless steels typically contain an extra 11% chromium. Steel's low price and high tensile strength make it a popular material for many different types of construction, as well as for transportation, manufacturing, and defense. Cast iron is the primary component of steel. It can crystallize in either a body-centered cubic or a face-centered cubic form, depending on the temperature. Steel and cast iron are characterized by a wide variety of properties due to the interaction of iron's various allotropes with the alloying elements, most notably carbon.

Want to know more about steel visit the link which is given below;

https://brainly.com/question/29222140

#SPJ4

A theory must meet certain requirements in order to be accepted as a physical law , 1. It must explain the available data 2. It need to offer hypotheses that can be verified by science.

A physical law outlines the broad relationships between and, when necessary, changes in the physical quantities that define the states of a physical system. Typically, this is described mathematically. These laws are also known as natural laws or are associated with them in the physical realm. A physical law applies with a very high probability when it falls within its scope of applicability. Physical experiments and observations that are specifically focused are used to test this validity range. The law is established if the outcomes match the predictions.

To know more about physical law

https://brainly.com/question/28274696

#SPJ4

The minimum force that allows the window washer to move upward is Mg. The force is in terms of mass and acceleration due to gravity.

Given:

M = Mass of the window washer

g = Acceleration due to gravity

The forces acting are:

Force due to gravity = M × g

Tension in the rope = Force applied by the washer

The net force is zero. Therefore, the tension is:

T - M × g = 0

T = Mg

Hence, the minimum force that allows the window washer to move upward is Mg. The force is in terms of mass and acceleration due to gravity.

To learn more about Force, here:

https://brainly.com/question/13191643

#SPJ12

If we have an unmarked magnet, hold it near a piece of steel and the end that attracts the steel is the north end.

What is the magnet?
A magnet is an object made of certain materials that produces a magnetic field. This field is invisible but is responsible for the most notable property of a magnet: a force that pulls on other ferromagnetic materials, such as iron, and attracts or repels other magnets. Magnets are widely used throughout the world in a variety of applications, from the simple refrigerator magnet to the most advanced technologies such as MRI machines. Magnets come in many shapes and sizes and can be natural or artificial. The magnetic field of a magnet is caused by the motion of electric charges and is measured in guess.

To learn more about magnet

https://brainly.com/question/14997726

#SPJ4

D. will most likely be thrown over the steering column. When an unrestrained occupant is in a motor vehicle that strikes a tree while traveling at 40 mph, the occupant will be thrown from the vehicle due to the force of the impact. Without a seatbelt, the occupant will be thrown forward over the steering column.

When a motor vehicle strikes a tree traveling at 40 mph, the unrestrained occupant will be thrown forward and over the steering column with a force that is greater than the force of the motor vehicle's deceleration. This is due to the fact that the occupant is not restrained and therefore is not held in place by the seatbelt, allowing them to travel at the same speed until acted upon by an external force.

When a motor vehicle strikes a tree traveling at 40 mph, the unrestrained occupant will be thrown forward and over the steering column with a force that is greater than the force of the motor vehicle's deceleration.

learn more about steering here

https://brainly.com/question/14467048

#SPJ4

A globe is a miniature replica of the planet. We can see the size, shape, and placement of continents and oceans, which is helpful.

A globe's stand is attached to the meridian. Latitude (coordinate) markings can be found on several meridian lines. These markings range from 0° at the equator to 90° at the north and south poles.

The Unisphere is tipped at an angle of 23.5 degrees, which corresponds to the tilt of the Earth.

The globe makes it possible to see the entire planet at a glance. Along with their latitudes and longitudes, it displays many nations, continents, and oceans. The units of latitude and longitude are degrees and minutes.

Altazimuth and Equatorial mounts are the two main categories of astronomical telescope mounts. The simplest sort of mount, known as an altazimuth (sometimes spelled alt-az), has two motions: azimuth (horizontal) and altitude (vertical).

To learn more about globe refer to:

https://brainly.com/question/10911108

#SPJ4

Using the Pythagorean theorem, we can determine that the best distance for the ladder is 20 feet away from the base of the building.

The third side of this triangle is unknown, so we will apply the Pythagorean theorem to determine it. There is 25 feet of ladder available, the wall is 15 feet above the ground, the ladder must be at least that high.

In order to calculate the distance between the ladder and the building =

X = √(25^2) - (15^2)

= 20 feet

Thus, the ladder should be placed 20 feet away from the base of the building.

To learn more about Pythagorean theorem, click here:

https://brainly.com/question/29769496

#SPJ4

The results in terms of wavelength, velocity, and frequency i.e (L,f,v) are as follow,.

(a) λ = v/f

(b) The value of the first minimum will be [tex]x =\sqrt{\frac{v^2}{4 f^2}+\frac{v L}{f}}[/tex]

(c) The position for the first maxima of 2nd speaker = [tex]$$x=\sqrt{\frac{v}{f}\left(\frac{v}{f}+2 L\right)}$$[/tex]

A waveform signal that is carried in space or down a wire has a wavelength, which is the separation between two identical places (adjacent crests) in the consecutive cycles. This length is often defined in wireless systems in meters (m), centimeters (cm), or millimeters (mm) (mm).

(a) Relation among velocity, wavelength and frequency can be defined the expression: v = fλ

From above, we can write, (λ) (wavelength) can  be equal to velocity (v) / Frequency (f)

So, λ = v/f

(b) path difference can be determined by using the expression: [tex]\Delta x=x_2-x_1 \\[/tex]

[tex]\Delta x=\sqrt{L^2+x^2}-L\end{aligned}$$[/tex]

So, for the first minimum, we can conclude the following:

[tex]$\left\{n x=\frac{d}{2}=\frac{v}{2 f}\right.$$$\frac{v}{2 f}=\sqrt{L^2+x^2}-L$$[/tex]

[tex]\left(\frac{v}{2 f}+L\right)^2 & =L^2+x^2 \\\\x^2 =\frac{v^2}{4 f^2}+L^2+\frac{v L}{f}-L^2 \\\\x =\sqrt{\frac{v^2}{4 f^2}+\frac{v L}{f}}[/tex]

(c) for first order maxima

[tex]$$\begin{aligned}& \Delta x=\lambda \\& \frac{v}{f}=\sqrt{L^2+x^2}-L\end{aligned}$$[/tex]

[tex]$$\begin{aligned}x^2 & =\frac{v^2}{f^2}+L^2+\frac{2 V L}{f}-L^2 \\x & =\sqrt{\frac{v^2}{f^2}+\frac{2 v L}{f}}\end{aligned}$$[/tex]

So, the position for the first maxima of 2nd speaker will be:

[tex]$$x=\sqrt{\frac{v}{f}\left(\frac{v}{f}+2 L\right)}$$[/tex]

For more questions on destructive interference

https://brainly.com/question/23594941

#SPJ4

The missing diagram is attached below:

Answer:

Ventilators are provided near ceilings in the rooms of our houses because the hot air is lighter and rises out of the room through the ventilators. Cool fresh air rushes into the room through the doors and windows to occupy its place.

In pan 1, when you spray the sand with water, the water will be absorbed by the sand and the sand will become more compact and dense. This is because water molecules will fill the spaces between sand particles and increase the weight of the sand.

In pan 2, when you set ice cubes on the sand, the ice cubes will begin to melt as they come into contact with the warmer sand. As the ice melts, the surrounding sand will become wet. The meltwater will also lower the temperature of the sand around the ice cubes.

The ice cubes will continue to melt until they are fully melted, and the water will be absorbed by the sand. The wet sand will be cooler than the dry sand. This process will cause a change in the temperature and moisture content of sand which can be observed and studied.

Read more about heat transfer :

https://brainly.com/question/16055406

#SPJ4

The area of the piston that holds the ride is 8333,33 [tex]cm^{2}[/tex]

For hydraulic press system pressure in = pressure out

P = Pressure

F = Force

A = Area

The formula P = [tex]\frac{F}{A}[/tex]

We know F1 = 72 N, A1 = 30 [tex]cm^{2}[/tex]

                F2 = 20000 N

The area of the piston that holds the ride = A2

P 1 = P2

[tex]\frac{F1}{A1}[/tex]  = [tex]\frac{F2}{A2}[/tex]

[tex]\frac{72 N}{30 cm^{2} }[/tex]   =  [tex]\frac{20000 N}{A2}[/tex]

A2 = 20000 N : ( [tex]\frac{72 N}{30 cm^{2} }[/tex] )

A2 = ( 20000 N x 30 cm2 ) : 72 N

     = 8333,33 cm2

More about hydraulic press at

https://brainly.com/question/15709279

#SPJ4

Answer:

The maximum amplitude of the resultant pulse would be 30 cm.

Explanation:

The maximum amplitude of the resultant pulse would be 30 cm.

The maximum amplitude of the resultant pulse would be the sum of the amplitudes of pulse A and pulse B, which is

20 cm + 10 cm = 30 cm.

This is because the maximum amplitude of the resultant pulse would occur when the two pulses are in phase, meaning they are both at their highest point at the same time.

When the two pulses are out of phase, their amplitudes will cancel each other out to some degree, resulting in a lower overall amplitude.

To learn more about Pulse:-

https://brainly.com/question/27205915?referrer=searchResults

https://brainly.com/question/16001036?referrer=searchResults

If the amplitude of pulse A is 20cm and that of pulse B is 10 cm, the maximum of the resultant pulse is 30 cm.

A sound wave's amplitude measures the height of the wave. When a sound is made, the maximum displacement of the medium's vibrating particles from their mean position determines the amplitude of the sound wave. It is the separation between the wave's crest or trough and its mean location.

The phenomenon of constructive interference occurs when two waves superimpose on each other in the same phase, with the resultant wave's amplitude being equal to the sum of the separate waves' amplitudes and producing the maximum amount of light.

The amplitude of pulse A is 20cm.

The amplitude of pulse B is 10cm.

Hence,  the maximum of the resultant pulse is = (20 cm + 10 cm) = 30 cm.

Learn more about amplitude here:

https://brainly.com/question/8662436

#SPJ2

The final speed of the second car is '2v' and the collision is elastic collision.

The elastic collision is one in which the system does not experience a net loss of kinetic energy as the result of a collision. In elastic collisions, momentum & kinetic energy are both conserved.

v′ = m1v1 + m2v2 /m1+m2

v ′ = m 1 v 1 + m 2 v 2/ m 1 + m 2

in which m1 is mass of body 1, v1 is its initial speed, m2 is mass of body 2, & v2 is the final speed at which the two objects will be moving after colliding.

m1v +0 = mv/3 +m/3v2

v2 = 2v

To know more about elastic collision visit:-

https://brainly.com/question/12644900

#SPJ4

When two bodies at equal temperature are brought in contact with each other then no heat flows between them and they are said to be in thermal equilibrium.

When the engine temperature eventually reaches the same level as the ambient temperature, thermal equilibrium has taken place. After being placed on the table and waiting a short while, a cup of hot tea cools to the same temperature as its surroundings.

This is where thermal equilibrium occurs. the set temperature at which all of a solid's mass melts. When the solid turns into a liquid, both the solid and the liquid coexist in the thermal equilibrium.

The individual drove himself to his location. The engine temperature was excessively high during that time, but it eventually dropped to the air temperature outside. When the engine temperature eventually reaches air temperature, thermal equilibrium has occurred.

To learn more about thermal equilibrium refer to:

https://brainly.com/question/14556352

#SPJ1

A(1) and (2) only of the following bodies are at thermal equilibrium when being put into contact. i.e. (1) A glass of water of internal energy E at 20 °C (2) Alcohol with unknown internal energy at 20 °C .

As internal energy is measured in terms of the body temperature, when two bodies are in thermal equilibrium, their internal energies will also be equal.

to know more about internal energy visit

https://brainly.com/question/11278589

#SPJ1

The law of reflection, The relationship between the angle of incidence and the angle of reflection is that they are equal.

The angle of incidence is the angle between the incoming light ray and the normal line (a line perpendicular to the surface of the reflecting material), and the angle of reflection is the angle between the reflected light ray and the normal line. When a light ray strikes a reflection surface at a certain angle, it will be reflected back at the same angle. This relationship is represented by the equation.

=> angle of incidence = angle of reflection

This relationship holds true for all types of electromagnetic waves and for all surfaces that are reflective, whether they are smooth or rough, opaque or transparent. It's important to note that this is true for regular reflection, which is defined as the reflection of light off a smooth surface. If the surface is rough, the light rays are reflected in many different directions, this is called diffuse reflection.

To know more about reflection please refer: https://brainly.com/question/15655610

#SPJ4

When a lead rider's left arm is bent at the elbow with their index finger pointing straight up, it means double file formation.

When riding in groups, hand signals are a crucial aspect of communication. The group should create a double-file formation when the lead rider's left arm is bent at the elbow and their index and middle fingers are pointed straight up. Wider hallways are best suited for heavy-headed formations (T-formation with a couple of individuals in front) or double-file formations because soldiers can spread out and walk shoulder to shoulder at the front of the file. When opposing doors are visible, the single file configuration is constricting and slowly moving.

Learn more about elbow here:-

https://brainly.com/question/8720670

#SPJ4