Answer: 22.4%
Explanation: A = 49/201 0.24378109 B= 11/49 0.2244898 AxB/A I took the quiz, this is correct
The probability that a randomly selected player won a bronze medal given that the player represented Spain is b)24.4%.
To calculate this probability, we need to use conditional probability formula: P(Bronze Medal | Spain) = P(Spain and Bronze Medal) / P(Spain), where P(Spain and Bronze Medal) represents the number of players from Spain who won a bronze medal, and P(Spain) represents the total number of players who represented Spain.
From the given two-way frequency table, we can see that there were a total of 25 players who represented Spain, and 11 of them won a bronze medal. So, P(Spain and Bronze Medal) = 11/100.
Similarly, the total number of players who represented Spain is 25 + 19 + 13 = 57. So, P(Spain) = 57/100.
Now, we can substitute these values into the conditional probability formula to get: P(Bronze Medal | Spain) = (11/100) / (57/100) = 0.244 or 24.4%.
Therefore, the answer is B. 24.4%.
For more similar questions on probability theory.
brainly.com/question/13604758
#SPJ11
Using the heat of vaporization of benzene, 395 J/g, calculate the grams of benzene that will condense at its boiling point if 8.44 kJ is removed.
Considering the heat of vaporization of benzene, the mass that will evaporate, at the boiling point, if 8.44 kJ/g of heat is extracted is 21.36 g.
Given the heat of vaporization of benzene, 395 J/g and the heat removed, 8.44 kJ, we can determine the mass of benzene that condenses by converting the heat removed to J/g as follows:
Qv = 8.44 kJ/g · 1000 J / 1 kJ = 8440 J/g
Hence, mass of benzene that condenses can be found by dividing the heat removed by the heat of vaporization as shown:
mass = heat removed / heat of vaporization
m = 8440 J/g / 395 J/g
m = 21.36 g
Therefore, 21.39 g of benzene will condense at its boiling point if 8.44 kJ is removed.
See more about heat of vaporization at https://brainly.com/question/26306578.
#SPJ11
in an experiment, two objects, object x x and object y y , travel toward each other and collide. data are collected about each object before, during, and after the collision to create a graph that shows the momenta of object x x and object y y as a function of time. how should a student use the data found on the graph to verify the conservation of momentum?
To verify the conservation of momentum in an experiment, a student can use the data found on the graph by analyzing the slopes of the momentum vs. time curves for each object. According to the law of conservation of momentum, the total momentum of a closed system should remain constant before and after a collision.
Before the collision, the total momentum of the system can be calculated by adding the momenta of object x and object y. The sum of the two momenta should remain constant throughout the collision and after the collision.
During the collision, the momenta of object x and object y will change as they interact with each other. The slopes of the momentum vs. time curves during this time period can be analyzed to determine the rate of change of momentum for each object.
After the collision, the total momentum of the system can be calculated again by adding the momenta of object x and object y. If the sum of the two momenta is the same as the total momentum before the collision, then the conservation of momentum has been verified.
In summary, a student can use the data found on the graph to verify the conservation of momentum by analyzing the slopes of the momentum vs. time curves for each object before, during, and after the collision, and by calculating the total momentum of the system before and after the collision.
For more similar questions on momentum and collisions:
brainly.com/question/27519035
#SPJ11
choose the correct definition of electrical charge.
The quantity of electrical energy in an object determined by the presence or absence of protons or electrons is described by its electrical charge, which is a fundamental feature of matter.
An object's electrical charge, which describes whether it contains electrons or protons and the amount of electrical energy associated with it as a result, is a fundamental feature of matter. All matter is formed of atoms, which contain positively charged protons, negatively charged electrons, and neutral particles called neutrons. The distribution of these particles determines an object's electrical charge.
Depending on whether an object has a shortage or an abundance of electrons, electrical charge can either be positive or negative. A substance that contains more protons than electrons is positively charged, whereas a substance with more electrons than protons is negatively charged.
Learn more about electrical charge here:
https://brainly.com/question/30589729
#SPJ4
a uniform meter stick supported at the 25 cm mark is in equilibrium when a 1 kg rock is hung from the 0 cm end is the mass of the meterstick greater than, equal to, or less than the mass of the rock?
The mass of the meter stick is equal to the mass of the rock. This is because a meter stick in equilibrium is balanced, meaning that the weight of the rock on the left side of the meter stick (at 0 cm) is equal to the weight of the meter stick on the right side (at 25 cm).
What is the mass of the meter stick?When a 1 kg rock is hung from the 0 cm end of a uniform meter stick that is supported at the 25 cm mark and is in equilibrium, the mass of the meter stick is less than the mass of the rock.
A uniform meter stick supported at the 25 cm mark is in equilibrium when a 1 kg rock is hung from the 0 cm end. Since the meter stick is in equilibrium, the net torque acting on it is zero, which means that the meter stick is in rotational equilibrium around the support point at the 25 cm mark.
The gravitational force on the rock acts downward while the force on the meter stick acts upward due to the support point, and the net torque is zero.
As a result, the weight of the meter stick is less than the weight of the rock, since the gravitational force acting on the rock is greater than the gravitational force acting on the meter stick, and the net torque produced by the rock is equal to the net torque produced by the meter stick. The mass of the meter stick is therefore less than the mass of the rock.
Read more about mass here:
https://brainly.com/question/19385703
#SPJ11
Biofilms, which are colonies of bacteria that can cling to living or inert surfaces, can cause a wide array of human infections. Infections caused by bacteria living within biofilms are often chronic because antibiotics that are applied to the surface of a biofilm have difficulty penetrating through the film thickness. Consider a biofilm that is associated with a skin infection. An antibiotic (species A) is applied to the top layer of a biofilm (species B) so that a fixed concentration of medication, CA,0 = 4 x 10-3 kmol/m3 , exists at the upper surface of the biofilm. The diffusion coefficient of the medication within the biofilm is DAB = 2 x 10-12 m 2 /s. The antibiotic is consumed by biochemical reactions within the film, and the consumption rate depends on the local concentration of medication expressed as RA= - k1CA where k1 =0.1 s-1 . To eradicate the bacteria, the antibiotic must be consumed at a rate of at least 0.2 x10-3 kmol/s .m3 since, at smaller absolute consumption rates, the bacteria will be able to grow back faster than it is destroyed. Determine the maximum thickness of a biofilm, L, that may be treated successfully by the antibiotic.
i need written answer solved neatly not typed and answer should be correct . the answer is 5.9 micrometer
The maximum thickness of a biofilm that may be treated successfully by the antibiotic is 5.9 micrometers.To determine the maximum thickness of a biofilm that may be treated successfully by the antibiotic, we need to calculate the concentration of the antibiotic as a function of depth within the biofilm and determine whether the consumption rate meets the required threshold.
We can use Fick's second law of diffusion to describe the diffusion of the antibiotic within the biofilm:
dC/dt = D(d^2C/dx^2) - RA
where C is the concentration of the antibiotic, t is time, x is the depth within the biofilm, D is the diffusion coefficient of the medication within the biofilm, and RA is the consumption rate of the antibiotic due to biochemical reactions within the film.
Assuming steady-state conditions, we can set dC/dt = 0 and rearrange the equation to get:
(d^2C/dx^2) = RA/D
Integrating twice with the boundary conditions C = CA,0 at x = 0 and C = 0 at x = L, we obtain:
C(x) = CA,0 [1 - (sinh((L - x)/δ) / sinh(L/δ))]
where δ = sqrt(D/k1CA,0) is the thickness of the concentration boundary layer.
To determine the maximum thickness of a biofilm that can be successfully treated, we need to find the depth L at which the consumption rate of the antibiotic is at least 0.2 x 10^-3 kmol/s.m^3. We can calculate the consumption rate as:
RA = k1 C = k1 CA,0 [1 - (sinh((L - x)/δ) / sinh(L/δ))]
Integrating from x = 0 to L, we get:
RA = k1 CA,0 [L - δ coth(L/δ)]
Setting this expression equal to the required consumption rate of 0.2 x 10^-3 kmol/s.m^3, we can solve for L:
0.2 x 10^-3 kmol/s.m^3 = k1 CA,0 [L - δ coth(L/δ)]
L = 5.9 micrometers
Therefore, the maximum thickness of a biofilm that may be treated successfully by the antibiotic is 5.9 micrometers.
For more such questions on Antibiotic
https://brainly.com/question/16350442
#SPJ11
When using compass orientation, migrating animals make use of _____.a. memories from previous trips with parentsb. familiar landmarks and olfactory cuesc. the north and south polesd. the sun, stars, and Earth's magnetic field
When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.
Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.
Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.
Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.
Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.
These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.
Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.
All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.
for similar question on magnetic field to navigate.
https://brainly.com/question/22986969
#SPJ11
when you weigh yourself on a bathroom scale in an elevator moving upward at constant velcoity are the springs in the scale more or less compressed moving downward at constant velocity.T/F
True. The springs in the scale will be more compressed when the elevator is moving upward at constant velocity. When the elevator is moving downward at a constant velocity, the springs will be less compressed.
When you are in an elevator that is moving upward at a constant velocity and you weigh yourself on a bathroom scale, the springs in the scale will be more compressed because of the additional upward force caused by the motion of the elevator.
Likewise, when you weigh yourself on a bathroom scale in an elevator moving downward at a constant velocity, the springs in the scale are less compressed. This is because the additional force caused by the motion of the elevator is in the opposite direction.
Thus, when the elevator moves upwards with a constant velocity, the scale will give a weight that is more than the actual weight. When the elevator moves downwards with a constant velocity, the scale will give a weight that is less than the actual weight.
Learn more about velocity here:
brainly.com/question/80295?source=archive
#SPJ11
true or false compressed air can be used for cleaning as long as it is less than 30 psi
Answer:
True according to section 6(a) in the OSH act, compressed air can be used when cleaning if it is less than 30 Psi.
consider a 10 m length of 2 cm-i.d tube. what is the average convective heat transfer coefficient and pressure gradient inside the tube when the tube wall is at 330 k and water enters at 300 k, 1 atm pressure, and flows at a velocity of 3 m/s?
The average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is: 1420 W/m²K and 2.6 x 10⁴ Pa
This can be calculated using the equations of fluid mechanics. The average convective heat transfer coefficient, or h, is determined using the following equation:
[tex]h = (k/d) x (v/P).[/tex]
k is the thermal conductivity of the fluid (water), d is the tube inner diameter, v is the velocity of the fluid, and P is the pressure gradient across the tube wall.
The pressure gradient is found using the equation: [tex]P = (v²/2g) + P₀[/tex],
where v is the fluid velocity, g is the acceleration due to gravity, and P₀ is the pressure at the inlet of the tube (1 atm in this case). Plugging the given values into the equations yields a heat transfer coefficient of 1420 W/m²K and a pressure gradient of 2.6 x 10⁴ Pa.
In conclusion, the average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is 1420 W/m²K and 2.6 x 10⁴ Pa, respectively.
To know more about heat transfer refer here:
https://brainly.com/question/30416117#
#SPJ11
For a UART module with (8N1) format (which means 8 data bits, No parity and 1 stop bit), and Baudrate of 1000 Baud-per-second. Assume the channel is used at its full capacity. choose all the true statements:1. The bitrate is 1000 bit/sec.2. The data rate is 1000 bit/sec.3. The data rate is 800 bit/sec.4. The bitrate is 2000 bit/sec.
The correct answers are 1,2, and 4: the bitrate is 1000 bit/sec, the data rate is 1000 bit/sec, the bitrate is 2000 bit/sec.
For a UART module with (8N1) format (which means 8 data bits, No parity and 1 stop bit), and Baudrate of 1000 Baud-per-second. Assume the channel is used at its full capacity. The correct answers are:
1. The bitrate is 1000 bit/sec.
2. The data rate is 1000 bit/sec.
4. The bitrate is 2000 bit/sec.
The bitrate of a UART module with (8N1) format and a baudrate of 1000 Baud-per-second is 1000 bit/sec. The data rate, which is the rate at which the signal is actually transmitted, is the same as the bitrate, in this case, 1000 bit/sec. The bitrate cannot be 2000 bit/sec because the baudrate is 1000 Baud-per-second.
Learn more about UART : https://brainly.com/question/13014495
#SPJ11
A force f = bx 3 acts in the x direction, where the value of b is 3. 7 n/m3. How much work is done by this force in moving an object from x = 0. 00 m to x = 2. 7 m?
The work done by the force in moving the object from x = 0.00 m to x = 2.7 m is 69.03 J.
To calculate the work done by a force, we can use the following formula:
[tex]$$W = \int F(x) dx$$[/tex]
where F(x) is the force as a function of position, and the integral is taken over the distance the object is moved.
In this case, the force is given by [tex]$F(x) = bx^3 = 3.7x^3$[/tex] [tex]N/m^3[/tex] . The distance the object is moved is from x = 0.00 m to x = 2.7 m. Therefore, we can calculate the work done by the force as follows:
[tex]$$W = \int_{0.00}^{2.7} F(x) dx = \int_{0.00}^{2.7} (3.7x^3) dx $$[/tex]
[tex]$$W = \left[\frac{3.7x^4}{4}\right]_{0.00}^{2.7} = \left[\frac{3.7(2.7^4)}{4}\right] - \left[\frac{3.7(0.00^4)}{4}\right]$$[/tex]
[tex]$$W = 69.03 \text{ J}$$[/tex]
Therefore, the work done by the force in moving the object from x = 0.00 m to x = 2.7 m is 69.03 J.
To learn more about work done:
https://brainly.com/question/30699148
#SPJ4
A solar sailplane is going from Earth to Mars. Its sail is oriented to give a solar radiation force of FRad = 7.70 × 102 N. The gravitational force due to the Sun is 173 N and the gravitational force due to Earth is 1.00 × 102 N. All forces are in the plane formed by Earth, Sun, and sailplane. The mass of the sailplane is 14,900 kg. What is the magnitude of the acceleration on the sailplane? Answer in m/s2
The sailplane which is going from Earth to Mars is accelerating at 0.033 m/s² in the direction of solar radiation force.
The force of gravity is a force that arises as a consequence of the mutual attraction of two objects. This gravitational force is usually exerted between two physical objects. Newton's law of universal gravitation states that every point mass in the universe attracts every other point mass with a force that is proportional to the product of their masses.
Acceleration is the rate at which an object changes its speed or direction. Acceleration is a vector quantity that can be positive or negative. If the acceleration is negative, the object slows down. If the acceleration is positive, the object speeds up.
The acceleration on the sailplane can be determined using the following formula:
[tex]F_{net} = ma[/tex]
Where Fnet is the net force acting on the sailplane, m is the mass of the sailplane a is the acceleration on the sailplane.[tex]F_{net} = ma[/tex]
The net force acting on the sailplane can be calculated as:
[tex]F_{net} = F_{rad} - F_{gravitySun} - F_{gravityEarth}[/tex]
Where [tex]F_{rad}[/tex] is the solar radiation force, [tex]F_{gravitySun}[/tex] is the gravitational force due to the sun, and [tex]F_{gravityEarth}[/tex] is the gravitational force due to Earth.
Putting the given values in the above formula:
[tex]F_{net} = 7.70 \times 10^2 N - 173 N - 1.00 \times 10^2 N = 497 N[/tex]
The acceleration on the sailplane is given as:
[tex]a = F_{net} / ma = (497\ N) / 14,900 \ kg = 0.033 \ m/s^2[/tex]
The magnitude of the acceleration on the sailplane is 0.033 m/s² (rounded to three significant figures).
Learn more about Newton's law:
https://brainly.com/question/28171613
#SPJ11
In raising a 5200-N piano with a pulley system, the workers note that for every 1.5 m of rope pulled downward, the piano rises 0.22 Ideally, find the force that is required to lift the piano. Express your answer to two significant figures and include the appropriate units.
The force required to lift the piano in the given situation is 753 N.
A pulley is a wheel with a groove that holds a cable or rope in place. The wheel's rotation helps to lift a heavy weight to a higher level. The effort required to move the weight is reduced as a result of this mechanism. One end of the rope is attached to the object to be raised, and the other end is pulled by someone or something.
The pulley is the mechanism that allows a force to be applied in one direction to produce motion in another direction. As a result, a pulley is a tool that enables you to lift an object more easily.
It is given that for every 1.5 m of rope pulled downward, the piano rises 0.22 m. Let x be the force required to lift the piano.
Let's begin by converting 0.22 m to cm:
1 m = 100 cm, so
0.22 m = 0.22 × 100 = 22 cm
Next, we can convert 5200 N to kg.
1 N = 1 kg.m/s^2, so
5200 N = 5200/9.8 = 530.61 kg
x is the force required to lift the piano.
Therefore, we can apply the following formula:
x = (force required)/(distance pulled by the workers)
x = (530.61 kg × 9.8 m/s²)/(1.5 m × 0.22 m) = 753 N.
Thus, the force required to lift the piano in the given situation is 753 N.
Learn more about Force:
https://brainly.com/question/13370981
#SPJ11
Three objects interact in a system that has a total initial momentum of 236 kg-m/s directed in the southeast direction. If there is no friction (external force) acting on the two objects, what is their momentum after 12 s?
The momentum of the objects after 12 seconds of the interaction is -236 kg-m/s
Step by step Explanation:
The three objects of a system that has a total initial momentum of 236 kg-m/s directed in the southeast direction.
If there is no friction (external force) acting on the two objects, the momentum of the object is the product of the mass and velocity of the object.
The formula for momentum is P = mv,
where P is momentum, m is mass, and v is velocity.
Furthermore, the direction of momentum is similar to the direction of velocity. The given initial momentum is [tex]P_1[/tex] = 236 kg-m/s directed in the southeast direction.
According to the law of conservation of momentum, the total momentum of the system must remain constant if there is no external force. As a result, the total momentum of the system will be the same before and after the interaction.
[tex]P_1 = P_2 + P_3[/tex]
Where, [tex]P_1[/tex] = Initial momentum of the system
[tex]P_2[/tex] = Momentum of the object after the interaction
[tex]P_3[/tex] = Momentum of the object after the interaction
Let [tex]P_2[/tex]be the momentum of object 2 and [tex]P_3[/tex] be the momentum of object 3.
P_2 = m_2v_2
[tex]P_2 = m_2v_2[/tex]
[tex]P_3 = m_3v_3[/tex]
After the interaction, the momentum of the system is:
[tex]P = P_2 + P_3[/tex]
Let's find P_2 and P_3 in terms of time since the direction and mass of the objects are not given.
[tex]P_1 = P_2 + P_3[/tex]
⇒ [tex]P_2 = P_1 - P_3[/tex]
We must discover the momentum of object 3. The initial momentum is southeast. It indicates that the momentum is in the opposite direction of northwest. If we call the north and west direction negative, then the southeast direction will be positive. This indicates that the momentum is negative.
Therefore, [tex]P_1 = P_2 + P_3[/tex] ⇒ -236 =[tex]-P_3 + P_2[/tex]
We are supposed to calculate their momentum after 12 seconds after the interaction. So, the external force will act on them during this interval of time. Due to the absence of external forces, the momentum of the objects will remain constant.
Hence, the momentum of the objects after 12 seconds of the interaction will remain the same as the momentum of the objects after the interaction.Therefore,
[tex]P = P_2 + P_3 = P_1P[/tex] = -236 kg-m/s
the momentum of the objects after 12 seconds of the interaction.
Learn more about momentum at : 'Formula for momentum' https://brainly.com/question/402617
#SPJ11
A parallel-plate capacitor of capacitance Chas plate area A and distance between plates d. The capacitor is connected to a battery with voltage V, fully charged and then disconnected. A slab of dielectric material with dielectric constant 4.0 is then inserted into capacitor, completely filling region between plates. A) After inserting the dielectric, the capacitance is now: B) After inserting the dielectric, the charge stored in the capacitor is now: C) After inserting the dielectric, the voltage across the capacitor is now: D) After inserting the dielectric, electric field is now
A) The capacitance of the parallel plate capacitor after inserting the dielectric material between the plates is 4 times of the original capacitance of the capacitor.
B) The charge stored in the capacitor after inserting the dielectric material is given by [tex]Q_2[/tex] = CV.
C) The voltage across the capacitor after inserting the dielectric material is [tex]V_2 = V_1 = V_B[/tex] = V.
D) The electric field after inserting the dielectric material is one-quarter of the electric field before inserting the dielectric material, [tex]E_2 = (1/4)E_1[/tex].
A) The capacitance of the parallel plate capacitor after inserting the dielectric material between the plates is given by:
C’ = kC
Where,
C = capacitance of the capacitor k = dielectric constant of the medium between the plates
Given, C’ = ? and k = 4.0, C = C
Using the formula above,
C’ = 4.0 × C = 4C
B) The charge stored in the capacitor can be determined by the formula below;
Q = CV
Before the dielectric was inserted,
[tex]Q_1 = CV_1[/tex]
Where, [tex]Q_1[/tex] = initial charge stored in the capacitor
[tex]V_1[/tex] = voltage across the capacitor before inserting the dielectric material
After the dielectric is inserted,
[tex]Q_2 = CV_2[/tex]
Where, [tex]Q_2[/tex] = final charge stored in the capacitor
[tex]V_2[/tex] = voltage across the capacitor after inserting the dielectric material
Using the above formula, we can write;
[tex]Q_2[/tex] = [tex]Q_1[/tex] = C[tex]V_1[/tex]= C([tex]V_1[/tex])C = C’/4 = (4C)/4 = C' [tex]V_2[/tex] = [tex]V_1[/tex] = V
Befor inserting the dielectric material, the capacitor was fully charged and then disconnected.
As the battery is removed, the voltage across the capacitor remains constant.
Therefore, the charge stored in the capacitor after inserting the dielectric material is the same as the initial charge which is given by
[tex]Q_2[/tex] = [tex]Q_1[/tex] = C[tex]V_1[/tex] = C[tex]V_B[/tex] = CV
C) The voltage across the capacitor before inserting the dielectric material is given by
[tex]V_1[/tex] = [tex]V_B[/tex] = V
Where V is the voltage of the battery connected to the capacitor.
As the voltage across the capacitor is the same before and after inserting the dielectric material, we have
[tex]V_2 = V_1 = V_B[/tex] = V
D) The electric field E can be determined using the formula below;
E = V/d
Before inserting the dielectric material,
[tex]E_1[/tex] = [tex]V_1[/tex] / d
Where, [tex]E_1[/tex] = electric field before inserting the dielectric material
[tex]V_1[/tex] = voltage across the capacitor before inserting the dielectric material
After inserting the dielectric material,
[tex]E_2[/tex] = [tex]V_2[/tex] / d
Where, [tex]E_2[/tex] = electric field after inserting the dielectric material
[tex]V_2[/tex] = voltage across the capacitor after inserting the dielectric material
Using the formula above, we can write;
[tex]E_2 = E_1/k[/tex]
Where, k = dielectric constant of the medium between the plates = 4.0
[tex]E_1 = \frac{V}{d} E_2[/tex] = [tex]\frac{V}{d} k[/tex][tex]= \frac{V}{4d} E_2[/tex] = [tex]\frac{1}{4}E_1[/tex]
For similar question capacitance
https://brainly.com/question/16998502
#SPJ11
a belt drive must transmit 10kw of power of 3984 rev/min. the wheel is 235 mm diameter and the coefficient of friction is 0.35. the lap angle is 150 degrees. the belt tension must not exceed 50 n. calculate the minimum number of belts required
The minimum number of belts required for a belt drive must transmit 10kw of power of 3984 rev/min is 9.
We can apply the formula: Power transmitted by the belt, P = (T₁ - T₂) × V where,
T₁ = Tight side tension
T₂ = Slack side tension
V = Velocity of the belt
Velocity of the belt, V = πdn/60 where,
d = Diameter of the wheel
n = Speed of the wheel in rev/min
Tight side tension, T₁ = T₂eμθ where,
e = Base of natural logarithm
According to the problem,
P = 10 kW = 10000 W
d = 235 mm = 0.235 m
n = 3984 rev/min
μ = 0.35
θ = 150° = 150° × π/180 = 2.618 rad
T = 50 N
n = ?
Now, substituting the given values in the formula, we get
V = πdn/60
= π × 0.235 × 3984/60
= 48.853 m/s
T₁ = T₂eμθ
= 50e0.35 × 2.618
= 256.219 N
P = (T₁ - T₂) × V
10000 = (256.219 - T₂) × 48.853
T₂ = 204.291 N
Total tension in the belt,
T₁ + T₂ = 460.51 N
Let the number of belts required be 'x'. Then,
Total tension in all the belts = T × x
Therefore, T × x = T₁ + T₂
T × x = 460.51
x = 460.51/50
x = 9.21
Since the number of belts cannot be in decimal form, we can round off the answer to the nearest whole number. Therefore, the minimum number of belts required is 9. Answer: 9.
More on belt drives and power: https://brainly.com/question/23526864
#SPJ11
the us buys bombs from russia under a nuclear peace treaty. assume the bombs are 100% u235. each bomb weighs one tonne of u235. by mixing the u235 from one bomb to obtain a total of 40,000 kg of fuel needed by one reactor for startup, how much natural uranium must be used? what is the final enrichment?
The final enrichment would be 97.5%, which is the amount of U235 in the total fuel, divided by the total weight of the fuel.
What is the amount of natural uranium must be used?Uranium from one bomb = 1 tons = 1000 kg. Uranium required for one reactor = 40,000 kg Percent enrichment of U-235 in uranium used for bomb = 100%.
Enrichment = (% of U-235 / % of U-238) +1
Natural Uranium contains 0.711% of U-235.
Calculations: As we know that Uranium from one bomb = 1 tonne = 1000 kg.
To obtain a total of 40,000 kg of fuel needed by one reactor for startup, we need to mix 40 bombs. Let's find out the total mass of U-235 present in 40 bombs:
Total mass of U-235 = 1000 × 40 = 40,000 kg.
Enrichment = (% of U-235 / % of U-238) +1
Let the percentage of U-238 = X
Enrichment = (100/ X) + 1
We know that Natural Uranium contains 0.711% of U-235, So the percentage of U-238 in natural uranium will be 99.289%
Let X = 99.289%
Enrichment = (100/ 99.289%) + 1
Enrichment = 1.007%
Thus, the mass of natural uranium used = 40,000/0.007 = 5,71,42,857.14 kg (approx)
Final enrichment = 1.007%
To learn more about the uranium :
https://brainly.com/question/179933
#SPJ11
(Figure 1) shows a collision between three balls of clay. The three hit simultaneously and stick together. Assume that m = 60 g and v = 2.9 m/s. ⬤↘ m 40 m/s, and 45°
←⬤ v 30 g
↑
⬤ 20 g and 2.0 m/s
Part A What is the speed of the resulting blob of clay? Express your answer with the appropriate units. V = ? Part B What is the movement direction of the resulting blob of clay? Express your answer in degrees below the horizontal. θ = ?
The speed of the resulting blob of clay is 20.99 m/s and the direction is 45.82⁰ below the horizontal.
Given :
Masses of balls of clay:
m₁ = 60g,
m₂ =20g,
m₃ = 30g.
Speed of balls of clay :
v₁ = 40m/s,
v₂= 2m/s,
v₃ = 2.9m/s
we can write the speed in vector form as :
υ₁ = 40( x + y)/ √2 m/s,
υ₂ = 2 y m/s,
υ₃ = 2.9 (-y) m/s, where x and y are unit vectors in perpendicular directions.
During a collision, the momentum remains conserved. Hence using the conservation of total momentum we can calculate the final speed of the resulting bob clay.
Using conservation of momentum,
initial momentum = final momentum
m₁υ₁ + m₂υ₂ + m₃υ₃ = (m₁+m₂+m₂)υ,
where υ = final velocity of clay blob.
Putting all the values in the above equation,
60 × 40( x + y)/ √2 + 20×2 y+30 ×2.9 (-y) = (60+20+30) υ
on solving the above equation, we get
υ = 14.63 x + 15.06 y
The magnitude of the final speed will be equal to √(14.63²+ 15.06²)
Final speed= 20.99 m/s.
and
Angle = tan⁻(15.06/14.63)
Angle = 45.82⁰ below the horizontal.
Therefore, the speed of the resulting blob of clay is 20.99 m/s and the direction is 45.82⁰ below the horizontal.
To learn more about momentum, click here :
https://brainly.com/question/17166755
#SPJ12
Which of the following nuclear fuels does a one solar mass star use over the course of its entire evolution?A. hydrogen and heliumB. hydrogen, helium, carbon, and neonC. hydrogenD. hydrogen, helium, carbon, neon, and oxygenE. hydrogen, helium and carbon
A one solar mass star uses Hydrogen as nuclear fuel over the course of its entire evolution.
Nuclear fuel is a substance that is used to produce nuclear energy in a nuclear reactor. Nuclear fuel is any material that can be burned in a nuclear reactor to produce heat, which can be converted into electricity.
Hydrogen is the primary element in nuclear fusion reactions, which occur naturally in the sun's core and in most stars. Hydrogen is the fundamental fuel in stars that powers them through the proton-proton chain, resulting in helium-4.
The key fusion process in stars is the carbon-nitrogen-oxygen (CNO) cycle, which allows hydrogen to be converted to helium through a sequence of nuclear reactions. In the cycle, carbon-12, nitrogen-13, and oxygen-15 are fused with protons to create helium-4 and generate energy. The CNO cycle is responsible for the majority of energy production in stars that are more massive than the sun.
Hence, the answer is Hydrogen.
To know more about Nuclear Fusion, refer here:
https://brainly.com/question/12701636#
#SPJ11
a 3 3-inch candle burns down in 12 hours. if b represents how much of the candle, in inches, has burned away at any time given in hours, t, write a proportional equation for b in terms of t that matches the context.
The proportional equation for the 3 3-inch candle that burns down in 12 hours in which it represented in terms of b is b/t = 11/4.
Step by step explanation:
We must understand that a 3-inch candle burns down in 12 hours, and that b reflects how much of the candle, in inches, has burned away at any time given in hours t in order to develop a proportional equation for b in terms of t that matches the context supplied.
Using proportionality, we can write that the amount of the candle burned is proportional to the time elapsed. As such:
b/t = k, where k is the constant of proportionality.
The problem states that the 3 3-inch candle burns down in 12 hours, so we can calculate k as follows:
k = b/t = 3 3 / 12 = 11/4.
Now, we can write the proportional equation in terms of t as follows: b/t = 11/4.
Learn more about proportional equation and time at : https://brainly.com/question/14070528
#SPJ11
A 33-inch candle burns down in 12 hours. If b represents how much of the candle, in inches, has burned away at any time given in hours, t, a proportional equation for b in terms of t that matches the context can be found in the following manner-
The length of the candle that burns away is proportional to the time, so we have the equation:b/t = k where k is a constant of proportionality. We don't know the value of k yet.
To find k, we need to use the given information. We know that the candle burns down to a length of 0 inches after 12 hours, which means that 33 - 0 = 33 inches of the candle has burned away. So we can plug in b = 33 and t = 12 and solve for k:
b/t = k
33/12 = k
11/4 = k
Now we have the constant of proportionality, k = 11/4. So the proportional equation for b in terms of t is:b/t = 11/4
Therefore, the proportional equation for b in terms of t that matches the context is b = (11/4)*t.
To learn more about proportional equations refer to: brainly.com/question/24868934
#SPJ11
the transportation of weathering products by wind, water flow, or ice flow is called
The transportation of weathering products by wind, water flow, or ice flow is called erosion.
A geological process called erosion involves the removal and movement of rock and soil by forces of nature including wind, water, and ice. Gravity, climatic patterns, and the characteristics of the materials are only a few of the variables that influence the process. Depending on the scope and severity of the process, erosion may have both good and negative consequences on the ecosystem. While erosion can result in beautiful natural features like canyons and waterfalls, it can also degrade the soil, pollute the water, and result in land loss. For the management of natural resources and the reduction of erosion's detrimental effects on the environment, understanding erosion is crucial.
Learn more about wind here:
https://brainly.com/question/12005342
#SPJ4
The transportation of weathering products by wind, water flow, or ice flow is called______.
A 91-kg hockey player on the austin bats team is at rest on the ice if he throws a 4 kg rock at 2.1 m/s. what is the resulting speed of the hockey player in m/s
это действие является рективным, формула которой такова: m1×v1 = – m2×v2
m1 - масса игрока
m2 - масса шайбы
v1 - скорость игрока
v2 - скорост шайбы.
отсюда, скорост игрокa: v1 = (m2×v2):m1 = 0.092 m/s
the beam is supported by the by 2 rods ab and cd that have cross sectional areas of 12mm2 and 8mm2 respectively. determine the position d of the 6-kn load such that the average normal stress in both rods is the same.
The average normal stress in both rods is same so the position d of the 6-KN load is 4.8m.
Step by step explanation:
The beam is supported by the by 2 rods AB and CD that have cross sectional areas of 12mm² and 8mm² respectively. The average normal stress in both rods is the same. We need to determine the position d of the 6-KN load.
Normal stress is a type of stress that happens when an object encounters a force perpendicular to the plane of its cross-sectional area. The normal stress is measured in Pascals (Pa).
Normal Stress = F / A
Where, F = Force
A = Area
Position d of the 6-KN load can be calculated as follows: Determine the shear force
V = (w₁ × a₁) + (w₂ × a₂) ...(1)
V = (6 × 2) + (6 × 3)V = 30kN
Normal stresses in rod AB :
Normal Stress = F / A
Normal Stress in AB = (30 × 1000) / (12 × 10^-6)
Normal Stress in AB = 2500000 Pa
Normal stresses in rod CD :
Normal Stress = F / A
Normal Stress in CD = (30 × 1000) / (8 × 10^-6)
Normal Stress in CD = 3750000 Pa
Let's assume the position of the 6 KN load is d metres from the support CD. Therefore the shear force on the rod CD due to the 6-KN load is 6 × d. Therefore the shear force on rod AB is 6 (5 - d).
Now by applying the principle of superposition, the shear force on rod CD due to the 6-KN load is V/2 + 6d and the shear force on rod AB is V/2 - 6(5 - d).
For the average normal stress in both rods to be equal, the normal stress in rod AB should be equal to the normal stress in rod CD.
(V/2 + 6d) / 12 × 10^-6 = (V/2 - 6(5 - d)) / 8 × 10^-6
= V + 72d = 15V - 120d
= 15V - V = 192dV
= 6 KN × 4/3 = 8 KN
Distance from support CD to the position of 6 KN load= d = 4.8 m
Therefore the position d of the 6-KN load is 4.8m.
Learn more about Normal Stress at : https://brainly.com/question/23270001
#SPJ11
A building contractor buys 70% of his cement from supplier A and 30% from supplier B. A total of 95% of the bags from A arrive undamaged, and a total of 90% of the bags from B arrive undamaged. Find the probability that a damaged bag is from supplier Upper A.
The probability that a damaged bag is supplied from supplier A is 53.8%.
There are two suppliers, A and B, from which a building contractor purchases cement in a ratio 70: 30.
The probability of a damaged bag of cement arriving from supplier A will be found in this question.
Bayes' Theorem, which is one of the most important concepts in statistics, will be used to solve this problem.
The following is the formula for Bayes' theorem:
P(A|B) = (P(B|A) x P(A))/P(B)
Where P(A) and P(B) are the probabilities of events A and B occurring, respectively, and P(B|A) is the probability of B given that A has occurred.
Let us suppose that a bag of cement is chosen at random and that it is damaged. We want to determine the probability that the bag was supplied by A.
Let D represent the event that a bag is damaged, and let A represent the event that the bag is supplied by supplier A.
Then, by Bayes' theorem, we have:
P(A|D) = (P(D|A) x P(A))/P(D)
The probability of a bag being damaged given that it was supplied by supplier A is 1 - 0.95 = 0.05, as stated in the problem.
Similarly, the probability of a bag being damaged given that it was supplied by supplier B is 1 - 0.90 = 0.10.
The probability of a bag being supplied by supplier A is 0.70, whereas the probability of a bag being supplied by supplier B is 0.30.
The probability of a bag being damaged is as follows:
P(D) = P(D|A) x P(A) + P(D|B) x P(B)
= 0.05 x 0.70 + 0.10 x 0.30 = 0.065
Therefore, the probability that a damaged bag was supplied by supplier A is as follows:
P(A|D) = (P(D|A) x P(A))/P(D)
= (0.05 x 0.70)/0.065 = 0.538
Therefore, there is a 53.8% chance that a damaged bag was supplied by supplier A.
Learn more about probability: https://brainly.com/question/24756209
#SPJ11
when the car is parking on the ramp, the breakaway friction is obviously greater than the down-ramp component of the weight of the car. use what you have learned so far, calculate the force required to move the car down the ramp.
The required force to move a car down a ramp is the total force of the static force and weight force.
The force required to move the car down the ramp is equal to the sum of the static friction and the down-ramp component of the weight of the car. The static friction can be calculated as follows:
Fstatic = μs • m • g
Where μs is the static friction coefficient of the ramp, m is the mass of the car, and g is the gravitational acceleration.
The down-ramp component of the weight of the car can be calculated as follows:
Fweight = m • g • sinθ
Where θ is the angle of the ramp.
Therefore, the total force required to move the car down the ramp is equal to the sum of the static friction and the down-ramp component of the weight of the car:
Ftotal = Fstatic + Fweight
Learn more about static friction at https://brainly.com/question/30031223
#SPJ11
the one property of a main-sequence star that determines all its other properties is its: question 1 options: 1) luminosity. 2) temperature. 3) mass. 4) spectral type.
The one property of a main-sequence star that determines all its other properties is its mass. Mass is the one property of a main-sequence star that determines all its other properties. The correct option is 3.
What is the main sequence star?A main-sequence star is a star that is in the process of fusing hydrogen to helium in its core. When a star is in this stage, it is in equilibrium, which means that the gravitational pull toward its core is balanced by the energy produced by nuclear fusion in the core. When a star is in equilibrium, the one property that determines all of its other properties is its mass.
The reason for this is because the mass of a star determines how much pressure and temperature are generated in the core, which ultimately determines how much energy is generated and how long it will last.
Other properties like luminosity, temperature, and spectral type all depend on the mass of the star. Therefore, the mass of a main-sequence star is the one property that determines all of its other properties.
Therefore, the correct option is 3.
Read more about main-sequence star here:
https://brainly.com/question/906581
#SPJ11
what is he probability of having exactly 10 samples succeed from a binomial random variable, if the sample size is 20, the probability of success is 51%?
The probability of having exactly 10 samples succeed from a binomial random variable, given a sample size of 20 and a probability of success of 51%, is 0.1011.
To calculate this, we can use the Binomial Probability formula:
P(x;n,p) = (n!/(x!*(n-x)!) * px * qn-x)
where P(x;n,p) is the probability of x successes in n trials with probability p, and q is the probability of failure, equal to 1-p.
In this case, x = 10, n = 20, and p = 0.51, so q = 0.49. Plugging these values into the formula, we get:
P(10;20,0.51) = (20!/(10!*10!) * 0.5110 * 0.4910) = 0.1011
Therefore, the probability of having exactly 10 successes is 0.1011.
for more such questions on Probability
https://brainly.com/question/13604758
#SPJ11
three forces applied to a trunk that moves leftward by 3.010 m over a frictionless floor. The force magnitudes are F1 = 5.86 N, F2 = 9.180 N, and F3 = 3.850 N, and the indicated angle is θ = 67.8°. During the displacement, what is the net work done on the trunk by the three forces? (Note that there are other forces acting on the block, but we only care about the net work done by these three forces.) And by how much does the kinetic energy of the trunk increase (enter a positive value) or decrease (negative value)?
The kinetic energy of the trunk increases by ½ mvf² = ½ m(10.65 m/s)²= 71.44 J during the displacement.
Net work = ΔK
W = Fd cosθ
W1 = F1d cosθ = (5.86 N)(3.010 m) cos(67.8°) = 6.99 J
W2 = F2d cosθ = (9.180 N)(3.010 m) cos(67.8°) = 10.97 J
W3 = F3d cosθ = (3.850 N)(3.010 m) cos(67.8°) = 4.58 J
Net work = W1 + W2 + W3 = 6.99 J + 10.97 J + 4.58 J = 22.54 J
Therefore, the net work done on the trunk by the three forces is 22.54 J.
ΔK = ½ mvf² - ½ mvi²
Since the trunk moves a distance of 3.010 m and is initially at rest, we can use the equation:
vf² = 2ad
where a is the acceleration of the trunk, which is given by:
a = ΣF / m
where ΣF is the net force on the trunk, which we can find using:
ΣF = F1 + F2 + F3
ΣF = (5.86 N + 9.180 N + 3.850 N) = 18.89 N
Therefore, the acceleration of the trunk is:
a = ΣF / m = 18.89 N / m
Since the trunk moves leftward, the acceleration is also leftward, so we can use a negative value for a.
Substituting the values for a and d, we get:
vf² = -2(-18.89 N / m)(3.010 m) = 113.51 (m/s)²
Taking the square root, we get:
vf = 10.65 m/s
Therefore, the change in kinetic energy of the trunk is:
ΔK = ½ mvf² - ½ mvi² = ½ m(10.65 m/s)²- 0 = ½ mvf²
Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv^2, where m is the mass of the object and v is its velocity.
Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.
To learn more about Kinetic energy visit here:
brainly.com/question/26472013
#SPJ4
shows the reverse current obtained for a si p-n junction diode at 300 k. the slight increase in reverse current at small reverse bias voltages ranging from -5 v to -25 v is due to
The slight increase in reverse current at small reverse bias voltages ranging from -5 V to -25 V is due to tunneling.
What is a Si p-n junction diode?A diode is a type of electrical component that allows electric current to flow in only one direction, and a p-n junction diode is a type of diode that is made up of p-type and n-type semiconductor materials. The current-voltage characteristic of a Si p-n junction diode at 300 K is given in the figure above. The slight increase in reverse current at small reverse bias voltages ranging from -5 V to -25 V is due to tunneling.
Tunneling is a quantum mechanical phenomenon in which particles penetrate through a potential barrier that would be impossible to overcome under the principles of classical mechanics. This phenomenon explains why the current flowing through a p-n junction increases at small reverse bias voltages.
The current in a Si p-n junction diode is extremely tiny when reverse-biased, but it begins to rise at a certain point, and this phenomenon is referred to as tunneling. The magnitude of this reverse-bias current is quite small, but it is not negligible, and it is referred to as the reverse saturation current.
Learn more about Si p-n junction here:
https://brainly.com/question/29513692
#SPJ11
if the leftover energy in the previous problem is 134.9 j (it's not, don't go back and try to use this value) and the mass is 2 kg, what speed (in m/s) does the block have at the bottom of its slide? revisit the definition of ke if needed.
The speed of the block at the bottom of its slide is 16.4 m/s.
In the previous problem, the kinetic energy of the block was found to be 135 J.
The formula for kinetic energy is
KE = 1/2mv²,
Where:
m is the mass of the object and v is its velocity.Now we can use the same formula to find the velocity of the block at the bottom of its slide.
KE = 1/2mv²
We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.
KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s
Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.
Learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11