calculate the height of a theoretical plate of species b in cm/plate. hint: you will want to calculate the number of plates first.

Answers

Answer 1

When it comes to chromatography, a theoretical plate refers to a hypothetical zone in the column where the concentration of solutes is uniform. To calculate the height of a theoretical plate for a given species, we need to first determine the number of plates present in the column.

The number of theoretical plates is a measure of the column efficiency, and it can be calculated using the following equation:

N = 16 (tR / w)^2

where N is the number of plates, tR is the retention time of the solute, and w is the peak width at half height.

Once we have determined the number of plates, we can calculate the height of a single plate by dividing the length of the column by the number of plates. This will give us the distance between two adjacent theoretical plates, which is commonly referred to as the plate height (H).

H = L / N

where L is the length of the column.

Finally, to calculate the height of a theoretical plate for species b in cm/plate, we would need to substitute the values of N and L into the above equation. This will give us the height of a single plate for that particular species.

I hope that helps! Let me know if you have any further questions.

For such more question on chromatography

https://brainly.com/question/28731153

#SPJ11


Related Questions

Lab scale tests performed on a cell broth with a viscosity of 5cP gave a specific cake resistance of 1 x1011 cm/g and a negligible medium resistance. The cake solids (dry basis) per volume of filtrate was 20 g/liter. It is desired to operate a larger rotary vacuum filter (diameter 8 m and length 12 m) at a vacuum pressure of 80 kPA with a cake formation time of 20 s and a cycle time of 60 s. Determine the filtration rate in volumes/hr expected for the rotary vacuum filter.

Answers

Answer:

5.118 m^3/hr

Explanation:

Given data:

viscosity of cell broth = 5cP

cake resistance = 1*1011 cm/g

dry basis per volume of filtrate = 20 g/liter

Diameter = 8m ,  Length = 12m

vacuum pressure = 80 kpa

cake formation time = 20 s

cycle time = 60 s

Determine the filtration rate in volumes/hr  expected fir the rotary vacuum filter

attached below is a detailed solution of the question

Hence The filtration rate in volumes/hr expected for the rotary vacuum filter

V' = ( [tex]\frac{60}{20}[/tex] ) * 1706.0670

   = 5118.201 liters  ≈ 5.118 m^3/hr

A 50-mm cube of the graphite fiber reinforced polymer matrix composite material is subjected to 125-kN uniformly distributed compressive force in the direction 2, which is perpendicular to the fiber direction (direction 1). The cube is constrained against expansion in direction 3. Determine:

a. changes in the 50-mm dimensions.
b. stresses required to provide constraints.

Answers

Answer:

hello some parts of your question is missing attached below is the missing part

answer :

A) Determine changes in the 50-mm dimensions

The changes are : 0.006mm compression  in y-direction

                               0.002 mm expansion in x and z directions

B) the stress required are evenly distributed

Explanation:

Given data :

50-mm cube of graphite fiber reinforced polymer matrix

subjected to 125-KN force in direction 2,

direction 2 is perpendicular to fiber direction ( direction 1 ) and cube is constrained against expansion in direction 3

A) Determine changes in the 50-mm dimensions

The changes are : 0.006mm compression  in y-direction

                               0.002 mm expansion in x and z directions

B) the stress required are evenly distributed

attached below is the detailed solution

who was part of dempwolf his firm when he first started

Answers

Explanation:

Dempwolf created by John Augustus, Among the most prominent innovative solutions in Southern California Pennsylvania was established by Dempwolf with  brother Reinhardt or uncle's son Frederick entered the company of J.A. Dozens of structures in 10 states were engineered by Dempwolf.

What current works best when the operator
encounters magnetic arc blow?

•DCEP

•ACEN

•CC

•AC

Answers

Answer:

AC

Explanation:

One situation when alternating current would work better than direct current is if the operator is encountering magnetic arc blow.

Current works best when the operator  encounters magnetic arc blow is AC

Magnetic arc blow is simply defined as the arc deflection due to the warping of the magnetic field that is produced by electric arc current.

This is caused as a result of the following;

- if the material being welded has residual magnetism at an intolerable level

- When the weld root is being made, and the welding current is direct current which indicates constant direction and maintains constant polarity (either positive or negative).

Since it is caused by DC(Direct Current) which means constant polarity , it means the opposite will be better which is AC(alternating current) because it means that electricity direction will be switching to and fro and as such the polarity will also be revered in response to this back and forth switch manner.

Thus, Current works best when the operator  encounters magnetic arc blow is AC

Read more at; brainly.in/question/38789815?tbs_match=1

A cylindrical bar of metal having a diameter of 15.7 mm and a length of 178 mm is deformed elastically in tension with a force of 49100 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34 respectively, Determine the following:(a) The amount by which this specimen will elongate (in mm) in the direction of the applied stress. The entry field with incorrect answer now contains modified data.(b) The change in diameter of the specimen (in mm). Indicate an increase in diameter with a positive number and a decrease with a negative number.

Answers

Answer:

0.6727

-0.02017

Explanation:

diameter = 15.7

l = 178

E =elastic modulus = 67.1 Gpa

poisson ratio = 0.34

p = force = 49100N

first we calculate the area of the cross section

[tex]A=\frac{\pi }{4} d^{2}[/tex]

[tex]A=\frac{\pi }{4} (15.7)^{2} \\A = \frac{774.683}{4} \\[/tex]

A = 193.6mm²

1. Change in directon of the applied stress

[tex]= \frac{pl}{AE}[/tex]

= 49100*178/193.6*67.1*10³

= [tex]=\frac{8739800}{12990560}[/tex]

δl = 0.6727  mm

2. change in diameter of the specimen

equation for poisson distribution =

m = -(δd/d) / (δl/l)

0.34 = (δd/15.7) / (0.6727/178)

0.34 = (-δd * 178) / 15.7 * 0.6727

0.34 = -178δd / 10.56139

we cross multiply

10.56139*0.34 =-178δd

3.5908726 = -178δd

δd = 3.5908726/-178

δd = -0.02017 mm

the change in dimeter has a negative sign. it decreases

The pressure less than atmospheric pressure is known as:

Suction pressure

Negative gauge pressure

Vacuum pressure

All of the above

Answers

Answer:

answer is option (d) all of the above

what is the distance in term of wavelengh between successive minima in the standing wave ratio​

Answers

Answer:

hi there

Explanation:

What are the top 4 solar inventions, how they are used, and how they are better than the original way of powering them

Answers

Yes I will answer soon

how skateboards works?

Answers

Answer

The skateboarder applies pressure to the trucks and gives/releases pressure on the levers. Second, the wheels and the axles are also examples of simple machines. They help the skater ride, spin, grind, and do a bunch of other radical movements on a skateboard.:

Explanation:

Check Your Understanding: True Stress and Stress A cylindrical specimen of a metal alloy 47.7 mm long and 9.72 mm in diameter is stressed in tension. A true stress of 399 MPa causes the specimen to plastically elongate to a length of 54.4 mm. If it is known that the strain-hardening exponent for this alloy is 0.2, calculate the true stress (in MPa) necessary to plastically elongate a specimen of this same material from a length of 47.7 mm to a length of 57.8 mm.

Answers

Answer:

The answer is "583.042533 MPa".

Explanation:

Solve the following for the real state strain 1:

[tex]\varepsilon_{T}=\In \frac{I_{il}}{I_{01}}[/tex]

Solve the following for the real stress and pressure for the stable.[tex]\sigma_{r1}=K(\varepsilon_{r1})^{n}[/tex]

[tex]K=\frac{\sigma_{r1}}{[\In \frac{I_{il}}{I_{01}}]^n}[/tex]

Solve the following for the true state stress and stress2.

[tex]\sigma_{r2}=K(\varepsilon_{r2})^n[/tex]

     [tex]=\frac{\sigma_{r1}}{[\In \frac{I_{il}}{I_{01}}]^n} \times [\In \frac{I_{i2}}{I_{02}}]^n\\\\=\frac{399 \ MPa}{[In \frac{54.4}{47.7}]^{0.2}} \times [In \frac{57.8}{47.7}]^{0.2}\\\\ =\frac{399 \ MPa}{[ In (1.14046122)]^{0.2}} \times [In (1.21174004)]^{0.2}\\\\ =\frac{399 \ MPa}{[ In (1.02663509)]} \times [In 1.03915873]\\\\=\frac{399 \ MPa}{0.0114161042} \times 0.0166818905\\\\= 399 \ MPa \times 1.46125948\\\\=583.042533\ \ MPa[/tex]

Describe how to contribute to
zero/low carbon work outcomes
within the built environment.

Answers

Answer:

day if you workout without Zero billing that means you're not sweating. Sweating you're not losing anything that means you have zero outcomes

Explanation:

An example of a power consuming device would be a(n) ____ while an example of a non-power consuming device would be a(n) ____.

Answers

An example of a power consuming device would be a(n) light bulb, a computer device while an example of a non-power consuming device would be a(n) switch or button.

What is power consumption?

The quantity of energy utilized per unit of time is known as power consumption. Power use is a significant factor in digital systems.

Power consumption is a limiting factor for the battery life of portable devices like laptop computers and cell phones.

Learn more about power consumption:
https://brainly.com/question/14860418
#SPJ1

This is silence I couldent find the tab... 30 points plus marked brainliest if corrects!


The most recent evidence supporting the theory of plate tectonics would include
es )
A)
GPS monitoring of plate speeds and movements.
B)
the WWII discovery of paleomagnetic reversals.
Elimi
O
the 1963 mapping of the tectonic plate boundaries.
D
C-14 dating of marine fossils found in the Himalayas.

Answers

Yeah the answer is A

A sign structure on the NJ Turnpike is to be designed to resist a wind force that produces a moment of 25 k-ft in one direction. The axial load is 30 kips. Soil conditions consist of a normally consolidated clay layer with following properties; su=800 psf, andγsat= 110 pcf. Design for a FOS of 3. Assume frost depth to be 3ft below grade

Answers

Solution :

Finding the cohesion of the soil(c) using the relation:

[tex]$c = \frac{q_u}{2}$[/tex]

Here, [tex]$q_u$[/tex] is the unconfined compression strength of the soil;

[tex]$c = \frac{800}{2}$[/tex]

   = 400 psf

∴ The cohesion value is greater than 0

So the use of the angle of internal friction is 0

Referring to the table relation between bearing capacity factors and angle of internal friction.

For the angle of inter friction [tex]$0^\circ$[/tex]

    [tex]$N_c = 5.14$[/tex]

   [tex]$N_q = 1.0$[/tex]

   [tex]$N_r = 0$[/tex]

Therefore,

[tex]$q_{ult} = (400 \times 5.14 )+(110 \times 3 \times 1.0)+(0.5 \times 100 \times 13 \times 0)$[/tex]

     =  2386 psf

∴ Allowable bearing capacity [tex]$q_{a} = \frac{Q_{allow}}{A}$[/tex]

                                                     [tex]$=\frac{30}{B^2}$[/tex]

∴ [tex]$q_a = \frac{q_{ult}}{F.O.S}$[/tex]

  [tex]$\frac{30}{B^2} = \frac{2386}{3}$[/tex]

∴ B = 0.2 ft

Therefore, the dimension of the square footing is 0.2 ft x 0.2 ft

                                                                                 [tex]$=0.04 \ ft^2$[/tex]

During a shrinkage limit test, a 19.3 cm3 saturated clay sample with a mass of 37 g was placed in a porcelain dish and dried in the oven. The oven-dried sample had a mass of 28 g with a final volume of 16 cm3 . Determine the shrinkage limit and the shrinkage ratio.

Answers

Answer:

shrinkae limit = 20.35%

shrinkage ratio = 1.45

Explanation:

1. to get the shrinkage limit we would first calculate the moisture content w.

w = (37-28)/28

= 9/28

= 0.3214

then the formula for shrinkage limit is

[tex][w-\frac{(V-Vd}{wd} ]*100[/tex]

w = 0.3214

V = 19.3

Vd = 16

Wd = 28

when we put these values into the formula:

[tex][0.3214-\frac{(19.3-16)}{28} ]*100\\[/tex]

= 20.35%

2. the shrinkage limit = Wd/V

= 28/19.3

= 1.45

Which of the following choices accurately contrasts a categorical syllogism with a conditional syllogism?


An argument constructed as a categorical syllogism uses deductive reasoning whereas an argument constructed as a conditional syllogism uses inductive reasoning.

A categorical syllogism contains two premise statements and one conclusion whereas a conditional syllogism contains one premise statement and one conclusion.

A categorical syllogism argues that A and B are both members of C whereas a conditional syllogism argues that if A is true then B is also true.

An argument constructed as a categorical syllogism is valid whereas an argument constructed as a conditional syllogism is invalid.

Answers

Answer:

The correct option is - A categorical syllogism argues that A and B are both members of C whereas a conditional syllogism argues that if A is true then B is also true.

Explanation:

As,

Categorical syllogisms follow an "If A is part of C, then B is part of C" logic.

Conditional syllogisms follow an "If A is true, then B is true" pattern of logic.

So,

The correct option is - A categorical syllogism argues that A and B are both members of C whereas a conditional syllogism argues that if A is true then B is also true.

With _____, only one criterion must evaluate true in order for a record to be selected and with _____, all criteria must be evaluate true in order for a record to be selected.

a. parameter criteria, double criteria
b. function criteria, IF criteria
c. simple criteria, complex criteria
d. OR criteria, AND criteria

Answers

Answer:

d

Explanation:

OR criteria, AND criteria

In an OR criteria, it doesn't need all the records to be true. Just one record is enough and all other criterion becomes true.

In an AND criteria, it's unlike the OR criteria and works in opposite. It needs every member of the record to be true to be able to adjudge the whole record as true.

And as such, we have

With OR criteria, only one criterion must evaluate true in order for a record to be selected and with AND criteria, all criteria must be evaluate true in order for a record to be selected.

If the sum of the two numbers is 4 and the sum of their squares minus three times their product is 76,find the number

Answers

Answer:

-2 and 6

Explanation:

Let "x" and "y" be 2 numbers.

The sum of the two numbers is 4. The mathematical expression is:

x + y = 4

y = 4 - x   [1]

The sum of their squares minus three times their product is 76. The mathematical expression is:

x² + y² - 3 x y = 76   [2]

If we substitute [1] in [2], we get:

x² + (4 - x)² - 3 x (4 - x) = 76

x² + 16 - 8 x + x² - 12 x + 3 x² = 76

5 x² - 20 x - 60 = 0

We apply the solving formula for second order equations and we get x₁ = 6 and x₂ = -2.

If we replace these x values in [1], we get:

y₁ = 4 - x₁ = 4 - 6 = -2

y₂ = 4 - x₂ = 4 - (-2) = 6

As a consequence, one of the numbers is 6 and the other is -2.

I don’t know the answer to this question

Answers

Answer:

I dont know the answer either

Explanation:

Answer:

flux

Explanation:

A single crystal of a metal that has the FCC crystal structure is oriented such that a tensile stress is applied parallel to the [100] direction. If the critical resolved shear stress for this material is 2.00 MPa, calculate the magnitude of applied stress necessary to cause slip to occur on the (111) plane in the direction.

Answers

Answer:

Explanation:

From the given information:

The equation for applied stress can be expressed as:

[tex]\sigma_{app} = \dfrac{\tau_{CRSS}}{cos \phi \ cos \lambda}[/tex]

where;

[tex]\phi[/tex] = angle between the applied stress [100] and [111]

To determine the [tex]\phi[/tex] and [tex]\lambda[/tex] for the system

Using the equation:

[tex]\phi= cos^{-1}\Big [\dfrac{l_1l_2+m_1m_2+n_1n_2}{\sqrt{(l_1^2+m_1^2+n_1^2)(l_2^2+m_2^2+n_2^2)}}\Big][/tex]

for [100]

[tex]l_1 = 1, m_1 = 0, n_1 = 0[/tex]

for [111]

[tex]l_1 = 1 , m_1 = 1, n_1 = 1[/tex]

Thus;

[tex]\phi= cos^{-1}\Big [\dfrac{1*1+0*1+0*1}{\sqrt{(1^2+0^2+0^2)(1^2+1^2+1^2)}}\Big][/tex]

[tex]\phi= cos^{-1}\Big [\dfrac{1}{\sqrt{(3)}}\Big][/tex]

[tex]\phi= 54.74^0[/tex]

To determine  [tex]\lambda[/tex]  for [tex][1 \overline 1 0][/tex]

where;

for [100]

[tex]l_1 = 1, m_1 = 0, n_1 = 0[/tex]

for [tex][1 \overline 1 0][/tex]

[tex]l_1 = 1 , m_1 = -1, n_1 = 0[/tex]

Thus;

[tex]\lambda= cos^{-1}\Big [\dfrac{1*1+0*1+0*0}{\sqrt{(1^2+0^2+0^2)(1^2+(-1)^2+0^2)}}\Big][/tex]

[tex]\phi= cos^{-1}\Big [\dfrac{1}{\sqrt{(2)}}\Big][/tex]

[tex]\phi= 45^0[/tex]

Thus, the magnitude of the applied stress can be computed as:

[tex]\sigma_{app} = \dfrac{\tau_{CRSS}}{cos \phi \ cos \lambda }[/tex]

[tex]\sigma_{app} = \dfrac{2.00}{cos (54.74) \ cos (45) }[/tex]

[tex]\mathbf{\sigma_{app} =4.89 \ MPa}[/tex]

Two sites are being considered for wind power generation. On the first site, the wind blows steadily at 7 m/s for 3000 hours per year. On the second site, the wind blows steadily at 10 m/s for 2000 hours per year. The density of air on the both sites is 1.25 kg/m3 . Assuming the wind power generation is negligible during other times.Calculate the maximum power of wind on each site per unit area, in kW/m2 .

Answers

Solution :

Given :

[tex]$V_1 = 7 \ m/s$[/tex]

Operation time, [tex]$T_1$[/tex] = 3000 hours per year

[tex]$V_2 = 10 \ m/s$[/tex]

Operation time, [tex]$T_2$[/tex] = 2000 hours per year

The density, ρ = [tex]$1.25 \ kg/m^3$[/tex]

The wind blows steadily. So, the K.E. = [tex]$(0.5 \dot{m} V^2)$[/tex]

                                                             [tex]$= \dot{m} \times 0.5 V^2$[/tex]

The power generation is the time rate of the kinetic energy which can be calculated as follows:

Power = [tex]$\Delta \ \dot{K.E.} = \dot{m} \frac{V^2}{2}$[/tex]

Regarding that [tex]$\dot m \propto V$[/tex]. Then,

Power [tex]$ \propto V^3$[/tex] → Power = constant x [tex]$V^3$[/tex]

Since, [tex]$\rho_a$[/tex] is constant for both the sites and the area is the same as same winf turbine is used.

For the first site,

Power, [tex]$P_1= \text{const.} \times V_1^3$[/tex]

            [tex]$P_1 = \text{const.} \times 343 \ W$[/tex]

For the second site,

Power, [tex]$P_2 = \text{const.} \times V_2^3 \ W$[/tex]

           [tex]$P_2 = \text{const.} \times 1000 \ W$[/tex]

An air heater may be fabricated by coiling Nichrome wire and passing air in cross flow over the wire. Consider a heater fabricated from wire of diameter D=1 mm, electrical resistivity rhoe=10−6Ω⋅m, thermal conductivity k=25W/m⋅K, and emissivity ε=0.20. The heater is designed to deliver air at a temperature of T[infinity]=50∘C under flow conditions that provide a convection coefficient of h=250W/m2⋅K for the wire. The temperature of the housing that encloses the wire and through which the air flows is Tsur=50∘C. If the maximum allowable temperature of the wire is Tmax=1200∘C, what is the maximum allowable electric current I? If the maximum available voltage is ΔE=110V, what is the corresponding length L of wire that may be used in the heater and the power rating of the heater? Hint: In your solution, assume negligible temperature variations within the wire, but after obtaining the desired results, assess the validity of this assumption.

Answers

Solution :

Assuming that the wire has an uniform temperature, the equivalent convective heat transfer coefficient is given as :

[tex]$h_T= \epsilon \sigma (T_s+T_{surr})(T_s^2 +T^2_{surr})$[/tex]

[tex]$h_T= 0.20 \times 5.67 \times 10^{-8} (1473+323)(1473^2 +323^2)$[/tex]

[tex]$h_T=46.3 \ W/m^2 .K$[/tex]

The total heat transfer coefficient will be :

[tex]$h_T=(250+46.3) \ W/m^2 .K$[/tex]

    [tex]$=296.3 \ W/m^2 .K$[/tex]

Now calculating the maximum volumetric heat generation :

[tex]$\dot {q}_{max}=\frac{2h_t}{r_0}(T_s-T_{\infty})$[/tex]

[tex]$\dot {q}_{max}=\frac{2\times 296.3}{0.0005}(1200-50)$[/tex]

        [tex]$= 1.362 \times 10^{9} \ W/m^3$[/tex]

The heat generation inside the wire is given as :

[tex]$\dot{q} = \frac{I^2R}{V}$[/tex]

Here, R is the resistance of the wire

         V is the volume of the wire

∴ [tex]$\dot{q} = \frac{I^2\left( \rho \times \frac{L}{A} \right)}{A \times L}$[/tex]

     [tex]$=\frac{I^2 \rho}{\left(\frac{\pi}{4}D^2 \right)}$[/tex]

where, ρ is the resistivity.

[tex]$I_{max}= \left(\frac{\dot{q}_{max}}{\rho} \right)^{1/2} \times \frac{\pi}{4}D^2$[/tex]

[tex]$I_{max}= \left(\frac{1.36 \times 10^9}{10^{-6}} \right)^{1/2} \times \frac{3.14}{4}(1 \times 10^{-3})^2$[/tex]

        = 28.96 A

Now considering the relation for the current flow through the finite potential difference.

[tex]$E=I_{max} \times R$[/tex]

[tex]$E=I_{max} \times \rho \times \frac{L}{A}$[/tex]

[tex]$L=\frac{AE}{I_{max} \ \rho}$[/tex]

[tex]$L=\frac{\frac{\pi}{4} \times (1 \times 10^{-3})^2 \times 110}{28.96 \times 10^{-6}}$[/tex]

   = 2.983 m

Now calculating the power rating of the heater:

[tex]$P= E \times I_{max}$[/tex]

[tex]$P= 110 \times 28.96}$[/tex]

   = 3185.6 W

   = 3.1856 kW

I have an AC waveform with the voltage peak value of 100 V. I'm trying to find the RMS value of the voltage​

Answers

Answer:

98 x 100=9,00

Explanation:

A group of students launches a model rocket in the vertical direction. Based on tracking data, they determine that the altitude of the rocket was 89.6 ft at the end of the powered portion of the flight and that the rocket landed 16.5 s later. The descent parachute failed to deploy so that the rocket fell freely to the ground after reaching its maximum altitude. Assume that g = 32.2 ft/s2.
Determine
(a) the speed v1 of the rocket at the end of powered flight,
(b) the maximum altitude reached by the rocket.

Answers

Answer:

[tex]u = 260.22m/s[/tex]

[tex]S_{max} = 1141.07ft[/tex]

Explanation:

Given

[tex]S_0 = 89.6ft[/tex] --- Initial altitude

[tex]S_{16.5} = 0ft[/tex] -- Altitude after 16.5 seconds

[tex]a = -g = -32.2ft/s^2[/tex] --- Acceleration (It is negative because it is an upward movement i.e. against gravity)

Solving (a): Final Speed of the rocket

To do this, we make use of:

[tex]S = ut + \frac{1}{2}at^2[/tex]

The final altitude after 16.5 seconds is represented as:

[tex]S_{16.5} = S_0 + ut + \frac{1}{2}at^2[/tex]

Substitute the following values:

[tex]S_0 = 89.6ft[/tex]       [tex]S_{16.5} = 0ft[/tex]     [tex]a = -g = -32.2ft/s^2[/tex]    and [tex]t = 16.5[/tex]

So, we have:

[tex]0 = 89.6 + u * 16.5 - \frac{1}{2} * 32.2 * 16.5^2[/tex]

[tex]0 = 89.6 + u * 16.5 - \frac{1}{2} * 8766.45[/tex]

[tex]0 = 89.6 + 16.5u- 4383.225[/tex]

Collect Like Terms

[tex]16.5u = -89.6 +4383.225[/tex]

[tex]16.5u = 4293.625[/tex]

Make u the subject

[tex]u = \frac{4293.625}{16.5}[/tex]

[tex]u = 260.21969697[/tex]

[tex]u = 260.22m/s[/tex]

Solving (b): The maximum height attained

First, we calculate the time taken to attain the maximum height.

Using:

[tex]v=u + at[/tex]

At the maximum height:

[tex]v =0[/tex] --- The final velocity

[tex]u = 260.22m/s[/tex]

[tex]a = -g = -32.2ft/s^2[/tex]

So, we have:

[tex]0 = 260.22 - 32.2t[/tex]

Collect Like Terms

[tex]32.2t = 260.22[/tex]

Make t the subject

[tex]t = \frac{260.22}{ 32.2}[/tex]

[tex]t = 8.08s[/tex]

The maximum height is then calculated as:

[tex]S_{max} = S_0 + ut + \frac{1}{2}at^2[/tex]

This gives:

[tex]S_{max} = 89.6 + 260.22 * 8.08 - \frac{1}{2} * 32.2 * 8.08^2[/tex]

[tex]S_{max} = 89.6 + 260.22 * 8.08 - \frac{1}{2} * 2102.22[/tex]

[tex]S_{max} = 89.6 + 260.22 * 8.08 - 1051.11[/tex]

[tex]S_{max} = 1141.0676[/tex]

[tex]S_{max} = 1141.07ft[/tex]

Hence, the maximum height is 1141.07ft

Tech A says that LED brake lights illuminate faster than incandescent bulbs. Tech B says that LED brake lights have
more visibility and last longer. Who is correct?

Answers

Answer:

Both

Explanation:

The driver of the truck has an acceleration of 0.4g as the truck passes over the top A of the hump in the road at constant speed. The radius of curvature of the road at the top of the hump is 98 m, and the center of mass G of the driver (considered a particle) is 2 m above the road. Calculate the speed v of the truck.

Answers

Answer:

19.81 m/s

Explanation:

The total acceleration of the truck (a) is due to the centripetal acceleration and as a result of the linear acceleration. Therefore the total acceleration (a) is given by:

[tex]a^2=a_n^2+a_t^2\\\\where\ a_n=centripetal\ acceleration=\frac{v^2}{r},a_t=linear \ acceleration\\\\But\ since\ the \ speed\ is \ constant, the \ linear \ acceleration(a_t)\ would\ be\ 0.\\\\a^2=a_n^2+a_t^2\\\\a^2=a_n^2\\\\a=a_n=\frac{v^2}{r} \\\\v^2=ar\\\\v=\sqrt{ar} \\\\a=0.4g=0.4*9.81,r=98\ m+2\ m=100\ m\\\\v=\sqrt{0.4*9.81*100} \\\\v=19.81\ m/s[/tex]

Now, you get a turn to practice writing a short program in Scratch. Try to re-create the program that was shown that turns the sprite in a circle. After you have completed that activity, see if you can make one of the improvements suggested. For example, you can try adding a sound. If you run into problems, think about some of the creative problem-solving techniques that were discussed.

When complete, briefly comment on challenges or breakthroughs you encountered while completing the guided practice activity.


Pls help im giving 100 points for this i have this due in minutes

Answers

Answer:

u need to plan it out

Explanation:

u need to plan it out

Answer:

use the turn 1 degrees option and put a repeat loop on it

Explanation:

u can add sound in ur loop

If the hypotenuse of a right triangle is 12 and an acute angle is 37 degrees find leg a and leg b lengths

Answers

scrity añao devid codicie

1. What is the productivity rate using cycle time for the following information:
I
Type of Work – Hauling
Average Cycle Time – 35 Minutes
Truck Capacity – 25 Tons
Crew - One Driver
Productivity Factor - 0.85
System Efficiency – 55 Minutes
per
Hour

Answers

ndjdjdhdjshdhdjdjjdjdjdjdhdhhdhdhdhdhdhdhdhdhdhdh

Find the derivative of x ​

Answers

Answer:

this is your answer. if mistake don't mind.

Other Questions
Companies like State Farm, a leading property and casualty insurance company, believe that the best way to create relationships with customers is to join them in activities they enjoy. Which type of market segmentation best captures this combination of age and interest in contemporary or alternative music Find DE3x - 283x - 30DGEF33 Joe needs to get to his house, which is 106 miles away in 2 hours. How fast does he need to drive? 48 mph 104 mph 0.019 mph 53 mph is natalie davis actively involved in the decisions of the business woolworths A man ordered 4 times as many boxes of ballpoint pens as boxes of felt-tip pens. Ballpoint pens cost $4.41 per box, and felt-tip pens cost $3.44. If the man's order of pens totaled $63.24, how many boxes of each type of pen did he buy?How many boxes of felt-tip pens did he buy? Early in the year, Marlon was in an automobile accident during the course of his employment. As a result of the physical injuries he sustained, he received the following payments during the year: If a problem is 8(2x+4) = 2(1x+3) is the first step done of PEMDAS for THIS SPECIFIC PROBLEM parentheses or multiplication? competition does not use price as a major promotional appeal, but instead stresses consumer benefits and product style. What is the value of x? Show your work.(Please hurry and see image for details.) When placed in a hypotonic solution, water moves into the cell through an aquaporin channel. this is an example of? The perimeter of a rectangle is 96 ft and the width is 22 ft what is the length of the rectangle When learning involves relating a response to more than one event or stimulus it is called:____. A patients urinalysis came back positive for glucose. What does the healthcear professional expect the patients blood glucose to be at a minimum? Identify the recursive formula for the sequence -3, 9, -27, 81, .... write an essay on how I answered the call Jenna collects stamps. She puts the same number of stamps on each page and then inserts each page into one of her two stamp books. One of her stamp books has a total of 840 stamps. The other has 1008. What is the largest number of stamps that Jenna could be putting on each page Type or copy and paste your revised informational text draft in the student response box, then read it aloud. As you read, pause to edit the draft using standard English conventions. Remember to follow these editing strategies:Answer: Here is Sutton's edited biography of Alexander Fleming:It is extremely uncommon to come across someone who alters how others perceive the world. One such person was Alexander Fleming. Before 1928, when Fleming's smart and creative mind developed it, penicillin, a treatment for numerous infections, did not exist.As a young man, Fleming was very interested in the study of medicine. Under the direction of bacteriologist Almroth Wright, he started his research career in 1906 at St. Mary's Hospital in London, England. During World War I, Fleming dealt with injured troops while serving in the Royal Army Medical Corps. He discovered that the liquid antiseptics used to treat wounds had a significant negative impact on a person's capacity to combat bacterial infections. He therefore thought that wounds should be kept clean and dry rather than being treated with antiseptics. His suggestions were mainly ignored, though.Fleming came back to St. Mary's in 1918 and was appointed the department's assistant director. He made an astonishing finding regarding the bacteria Staphylococcus aureus, which can result in serious human infections, ten years later, in September 1928. Fleming discovered an unfamiliar mold had grown around the bacteria after leaving it unattended in a petri dish.He was startled to learn through studying the mold that it was a form of antibiotica compound that can either kill or stop the growth of germs. Penicillin was given a name by him, and word of its therapeutic efficacy in treating bacterial infections quickly spread. After that, he was successful in stabilizing and purifying penicillin for use by the general population with the aid of scientists from the University of Oxford, Howard Florey and Ernst Chain.Penicillin's discovery changed medicine and made Alexander Fleming a hero. He was chosen as a Fellow of the Royal Society in 1943, and a year later, he was knighted. For the discovery of penicillin and their contributions to medicine, Fleming, Chain, and Florey were given the Nobel Prize in 1945.Later in life, Sir Alexander Fleming published numerous publications in international medical and scientific journals on topics like immunology, chemotherapy, and bacteriology. Fleming passed away in London in 1955, but his legacy is still honored today. Spending plans are divided into three categories with roughly ______% of the after tax budget going to the category of needs and _____________ % of the after tax budget going to wants, with the rest going to esi. List the functions of water in the body. Why is it important to maintain good fluid balance inside and outside of the cells To solve the equation 1. 75n = 7 for n, what operation must be applied to both sides in order to isolate the variable n?