Answer:
Solution:
1. Calculate the total volume of the two solutions:
Volume 1 = 100 cm3
Volume 2 = 50 cm3
Total Volume = 150 cm3
2. Calculate the total mass of each solution:
Mass of Solution 1 = (Volume x Density) x Mass Fraction HCl
= (100 cm3 x 1.180 g/cm3) x 0.36
= 43.2 g
Mass of Solution 2 = (Volume x Density) x Mass Fraction HCl
= (50 cm3 x 1.100 g/cm3) x 0.20
= 11 g
3. Calculate the total mass of the two solutions combined:
Total Mass = 43.2 g + 11 g
= 54.2 g
4. Calculate the mass fraction of hydrochloric acid in the new solution:
Mass Fraction HCl = Total Mass of HCl / Total Mass of Solutions
= 54.2 g / (43.2 g + 11 g)
= 0.55
Therefore, the mass fraction of hydrochloric acid obtained by merging 100 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 36%, and 50 cm3 of a solution of hydrochloric acid with a mass fraction of HCl 20%, is 0.55.
From a pH meter titration curve a student experimentally determines the pK a of benzoic acid to be 4.06. Calculate the experimental Ka for benzoic acid. If Ka for benzoic acid is 6.3 × 10-5 determine the percent error in their experimental results.
(1pts)
Experimental Ka for benzoic acid
(1pts)
Percent error to 2 significant figures
The percent error to 2 significant figures is 11%.
What is Titration?
Titration is a laboratory technique used to determine the concentration of a solution by reacting it with a standard solution of known concentration. The process involves adding the standard solution to the solution of unknown concentration until the reaction is complete, at which point the amount of standard solution needed to reach the endpoint is used to calculate the concentration of the unknown solution.
The relationship between pKa and Ka is given by:
pKa = -log(Ka)
Rearranging this equation, we get:
Ka = 10^(-pKa)
Substituting the given value of pKa = 4.06, we get:
Ka = 10^(-4.06) = 7.01 x 10^(-5)
The experimental Ka for benzoic acid is 7.01 x 10^(-5).
To calculate the percent error, we use the formula:
percent error = (|experimental value - accepted value| / accepted value) x 100%
Substituting the given values, we get:
percent error = (|7.01 x 10^(-5) - 6.3 x 10^(-5)| / 6.3 x 10^(-5)) x 100%
percent error = 11.19%
The percent error to 2 significant figures is 11%.
Learn more about Titration from given link
https://brainly.com/question/186765
#SPJ4
When Ibuprofen is given for fever to children 6 months of age up to 2 years, the usual dose is 5 milligrams (mg) per kilogram (kg) of body weight when the fever is under 102.5 degrees Fahrenheit. How much medicine would be usual dose for a 18 month old weighing 19 pounds?
54.58g of Medicine would be usual dose for a 18 month old weighing 19 pounds.
How can we calculate about the dose to be given by using information?Here, given that usual dose for children of use between 6 month to 2 year fever, is 5 mg per kg body weight.
1 kg body weight require 5 mg dose of medicine. and are have to find out how much dose of medicine
Required for 18 month children whose weighing is 24 pounds.
So, first are convert all the data in milligram because answer is required in mg. we know that
1 pound = 0.454K2
1 kg= 100 mg
.: 24 pounds = 24X0. 454 x 100 mg
[ 1 pound = 0.454 K2 then 24 pound = 24×0.454k2. and 24x0.454g = 24×0.454 × 100 mg
Now, 10 mg body weight remise dose is 5 mg then 24x054xlos my body.
required dose of children of 18 month and weighing is 24X0.454x100 mg is = 24x0.454x100 x 5 106 = 54.48 mg.
Answer: 54.48 mg.
To know more about Ibuprofen visit:
https://brainly.com/question/29807990
#SPJ1
the lattice enthalpy of licl is positive, indicating that it takes energy to break the ions apart in licl. however, the dissolution of licl in water is an exothermic process. identify all particle-particle interactions that contribute significantly to the dissolution process being exothermic. for each interaction, include the particles that interact and the specific type of intermolecular force between those particles.
When LiCl dissolves in water, the Li+ and Cl- ions become hydrated by water molecules, and these hydration interactions are the main contributors to the dissolution process being exothermic.
Specifically, the exothermicity arises due to the attractive electrostatic interactions between the ions and water molecules, which release energy as heat when the ions become surrounded by the solvent molecules.
In addition, the water molecules also form hydrogen bonds with each other and with the ions, further stabilizing the hydrated complex and contributing to the overall exothermicity of the process.
Therefore, the dissolution of LiCl in water is exothermic due to the particle-particle interactions between the ions and water molecules, including electrostatic interactions and hydrogen bonding.
To know more about the exothermic process, here
brainly.com/question/28741191
#SPJ4
B2F2 Spell out the full name of the compound
The full name of the compound B₂F₂ is diboron difluoride as it has 2 boron and fluorine atoms.
What is a compound?
Compound is defined as a chemical substance made up of identical molecules containing atoms from more than one type of chemical element.
Molecule consisting atoms of only one element is not called compound.It is transformed into new substances during chemical reactions. There are four major types of compounds depending on chemical bonding present in them.They are:
1)Molecular compounds where in atoms are joined by covalent bonds.
2) ionic compounds where atoms are joined by ionic bond.
3)Inter-metallic compounds where atoms are held by metallic bonds
4) co-ordination complexes where atoms are held by co-ordinate bonds.
Learn more about compounds,here:
https://brainly.com/question/13516179
#SPJ9
How many moles are in 202.33 grams of sulfuric acid
Answer:
8?
Explanation:
A sewage lagoon that has a surface area of 100,000 m2 (10 ha) and a depth of 1 m is receiving 8,640 m3/d of sewage containing 100 mg/L of biodegradable contaminant. At a steady state, the effluent from the lagoon must not exceed 20 mg/L of biodegradable contaminant. Assuming the lagoon is well mixed and that there are no losses or gains of water in the lagoon other than the sewage input, what biodegradation reaction rate coefficient (d-1) must be achieved?
The biodegradation reaction rate coefficient (d-1) must be achieved for the required concentration of exit stream is 0.003456 /day.
What is biodegradation ?
The term biodegradation is defined as the degradation of the materials into environmentally acceptable products such as water, carbon dioxide, and biomass by the action of naturally available microorganisms under normal environmental conditions.
Suppose C₀ represent the initial concentration of the biodegradable organic material = 100 g/L = 100 g/m³
Then,C be the concentration of biodegradable organic material that leaves the lagoon = 20 mg/L = 20 g/m³
Now, the rate constant be k
Let V be the volume of the lagoon
= 10 hectares × 1 m
= 100000 × 1
= 100000 m³
F₀ be the flow rate of in fluent into the first lagoon = 8640 m³/day
(kC₀V/F₀) = (C₀ - C)/C
(k×100×100000/8640)
= (100-20)/20
k = (4×8640)/(100×100000)
= 0.003456 /day
Thus, The biodegradation reaction rate coefficient (d-1) must be achieved for the required concentration of exit stream is 0.003456 /day.
To learn more about the biodegradation, follow the link;
https://brainly.com/question/23858132
#SPJ9
What is needed for photosynthesis to take place? (Select all that apply.)
energy
carbon dioxide
water
glucose
Answer:
Explanation:
water, carbon dioxide and energy (sunlight)
How many electrons in an atom can have the following quantum numbers?
n = 8, ℓ = 2
Answer:
Explanation:
The number of electrons that can have a specific set of quantum numbers in an atom is determined by the following formula:
2(2ℓ + 1)
where ℓ is the azimuthal quantum number.
So, for n = 8 and ℓ = 2, the number of electrons that can have these quantum numbers is given by:
2(2 * 2 + 1) = 2 * 5 = 10
Therefore, 10 electrons in an atom can have the quantum numbers n = 8 and ℓ = 2.
what is the balance of _NaCl + _F2 --> _NaF + _Cl2
Answer:
The balanced equation is
2NaCl + F2 ---> 2NaF + Cl2
What things are happening in the reaction tube upon changing the reaction buffer to an extremely high pH? Select all that apply
- The enzyme is denatured
- The phenolphthalein is degraded
- The phenolphthalein is denatured
- The solution turns clear
- The phenolphthalein structure is altered
The solution becomes clear, the enzyme is denatured, and the structure of phenolphthalein is changed.
When the reaction buffer is raised to an extremely high pH, the enzyme is denatured, the solution turns clear, and the structure of the phenolphthalein in the reaction tube is altered.
When acidic or basic compounds are added, a substance is said to be a buffer if it can resist the pH change. It may neutralise minor quantities of acid or base, essentially maintaining the solution's pH. For processes and/or reactions that require a certain and constant pH, this is essential.
These tubes provide the optimum environment for small-scale biological response or suspension culture research that need for aseptic conditions with gas exchange.
To know more about buffer
https://brainly.com/question/22821585
#SPJ4
The drawings below represent four different forms of electromagnetic energy.
Which diagram represents electromagnetic energy with the longest wavelength?
A
B
C
D
The diagram B represents electromagnetic energy with the longest wavelength.
What is wavelength ?
The Greek letter lambda (λ), which represents wavelength, is frequently used. When describing modulated waves, their sinusoidal envelopes, or waves created by the interference of several sinusoids, the term wavelength is also occasionally used.
What is electromagnetic energy ?
Radiant energy called electromagnetic energy moves in waves at the speed of light. It can also be referred to as radiant energy, light, electromagnetic waves, electromagnetic radiation, or the motion of electromagnetic waves. Heat can be transferred through electromagnetic radiation.
Therefore, The diagram B represents electromagnetic energy with the longest wavelength.
Learn more about wavelength from the given link.
https://brainly.com/question/16051869
#SPJ1
PLS SOMONE HELP I KNOW THE PHOTO ISNT THAT GOOD BUT I REALLY NEED HELP I WILL MARK AS BRAINLIEST AND GIVE 5 STARS ASWELL AS A HEART PLSS IM BEGGING YOU
The statement that best explains why the chemical equation provided for combustion of methane supports law of conservation of mass is as follows: There is same number of each kind of atom before and after the chemical reaction and the total mass remains the same (option D).
What is law of conservation of mass?The law of conservation of mass is a conservation law that states that the total mass of a closed system remains constant regardless of the chemical or physical changes that take place within it.
The law of conservation of mass further explains that in a chemical reaction, the amount of each atom on both sides of the equation is the same.
According to this question, methane gets combusted in air. To fulfill the law of conservation of mass, the same number of each kind of atom before and after the chemical reaction and the total mass remains the same.
Learn more about law of conservation of mass at: https://brainly.com/question/28711001
#SPJ1
A hydrate of sodium carbonate, Na₂CO3, has a mass of 4.31 g before heating. After heating, the mass of the anhydrous
compound is found to be 3.22 g.
What is the mass of water in the original sample?
A hydrate of sodium carbonate, Na[tex]_2[/tex]CO[tex]_3[/tex] has a mass of 4.31 g before heating. After heating, the mass of the anhydrous compound is found to be 3.22 g. Therefore, The mass of water in the original sample is 1.09g.
What is sodium carbonate?Sodium carbonate is an inorganic compound with the formula Na[tex]_2[/tex]CO[tex]_3[/tex], where x may range from 0 and 10. All forms are water-soluble, white, unscented salts that generate alkaline water solutions. It was historically made first from ash of plants grown in sodium-rich soil.
Before heating, a hydrates of sodium carbonate, Na[tex]_2[/tex]CO[tex]_3[/tex], does have a mass of 4.31 g. The weight of the anhydrous salt after heating is determined to be 3.22 g. The original sample contains 4.31-3.22 =1.09g of water.
Therefore, the mass of water in the original sample is 1.09g.
To learn more about sodium carbonate, here:
https://brainly.com/question/28236059
#SPJ9
A chemistry class is experimenting with iodine to see which common white powder items will react and make the iodine change color. Which item listed will have a chemical reaction with iodine?
A. baking soda
B. cornstarch
C. salt
D. powdered sugar
Answer:
B. Cornstarch
Explanation:
Iodine reacts with some substances and changes color as a result of the reaction. Out of the items listed:
B. Cornstarch will react with iodine and produce a blue-black color. This reaction is due to the presence of starch, which reacts with iodine to form a complex molecule called iodine starch.
A. Baking soda, also known as sodium bicarbonate, does not react with iodine and will not cause a color change.
C. Salt, also known as sodium chloride, does not react with iodine and will not cause a color change.
D. Powdered sugar, also known as sucrose, does not react with iodine and will not cause a color change.
*You have a 1.2 M solution of CaCi, that has a final volume of 0.050 L a.
How many moles of CaCly are generated in the reaction?
b.
How many grams of CaCly are generated in the reaction?
The number of moles is 0.06 moles while the mass is 6.66 g
What is the mole?The mole is a unit of measurement used in chemistry to express amounts of a substance. One mole of a substance is defined as the amount of that substance that contains as many entities, such as atoms, molecules, or ions, as there are in 12 grams of carbon-12, which is a common isotope of carbon.
Number of moles = 1.2 * 0.05
= 0.06 moles
Mass of the CaCl2 = 0.06 moles * 111 g
= 6.66 g
The mole is used to make it easier to compare the amounts of different substances in chemical reactions, and to calculate the amounts of reactants needed to produce a certain amount of product.
Learn ,more about mole:https://brainly.com/question/26416088
#SPJ1
which of the following birth outcomes are possible as a result of prenatal exposure to airborne polycyclic aromatic hydrocarbons (pahs)? select all that are true.
The birth outcomes are possible as a result of prenatal exposure to airborne polycyclic aromatic hydrocarbons is the correct option is e) All of the above.
The birth outcomes that are possible as the result of the prenatal exposure to the airborne polycyclic aromatic hydrocarbons are :
a) Reduced birth length
b) Reduced birth weight
c) Smaller head circumference
d) Shortened gestation
The Prenatal exposure to the PAHs has been connected with the ADHD that is the symptoms of the anxiety, the depression and the inattention, and also the behavioral disorders, that are all thought to the related to the deficits in the self - regulation.
To learn more about polycyclic aromatic here
https://brainly.com/question/15060847
#SPJ4
This question is incomplete, the complete question is :
which of the following birth outcomes are possible as a result of prenatal exposure to airborne polycyclic aromatic hydrocarbons (PAHs)? select all that are true.
a) Reduced birth length
b) Reduced birth weight
c) Smaller head circumference
d) Shortened gestation
e) All of the above
balance the following equation using the smallest possible integers and determine the coefficient of hcl? fe2s3 hcl --> fecl3 h2s
The balanced chemical equation for the given reaction is given as,
Fe₂S₃ + 6HCl → 2FeCl₃ + 3H₂S
A balanced chemical equation is defined as an equation where the number of atoms of each type in the reaction is the same on both reactants and product sides. Generally, the mass, as well as the change, are equal in a balanced chemical equation.
Basically chemical equation is said to be unbalanced if the number of atoms of each element on the left-hand side is not equal to the number of atoms present on the right-hand side. The balanced chemical equation remains always in accordance with the Law of Conservation of Mass.
The coefficient of the HCl is 6.
Learn more about balanced chemical reaction from the link given below.
https://brainly.com/question/28294176
#SPJ4
Iron (II) sulfide contains 36.47% sulfer by mass. If 87.91 g of iron sulfide is made by reacting iron with sulfer, what mass of iron was reacted?
36.47% of the mass of iron (II) sulfide is sulfur. If 87.91 g of iron sulfide is produced by reacting iron with sulfur, the amount of iron that was reacted is 87.91 g Fe(II) sulfur multiplied by 63.53% Fe (II) equals 55.85 g Fe (II)
What is meant by sulfur?The chemical element sulfur, which has an atomic number of 16, is known to people because it is thought to be the least reactive element. Prior to that, it was employed in the vulcanization of natural rubber as well as the production of fertilizers. Sulfur is used to vulcanize black rubber, as a fungicide, and in the production of black gunpowder. The creation of sulfuric acid, possibly the most significant chemical produced by western civilizations, uses the majority of sulfur, though.Sulfur is not hazardous to humans at all. A burning sensation or diarrhea could, however, result from consuming too much sulfur. Inhaling sulfur dust may aggravate the airways or result in coughing. Additionally, it might irritate your skin and eyes.To learn more about sulfur, refer to:
https://brainly.com/question/15654465
#SPJ4
draw the structural formula(s) for the organic product(s) formed when the following compound is heated at reflux in an excess of concentrated .
1,3 diiodo propane is formed when oxetane is heated at reflux.
Reflux is defined as the process which involves heating the chemical reaction for a specific amount of time, while continually cooling the vapor produced back into liquid form, using a condenser. The vapors that are produced above the reaction continually undergo condensation, returning to the flask as a condensate.
Oxetane is a stable carbon compound which shows characteristic properties when reacted with conc. acids. When oxetane reacts with HI it gets reduced to form 1,3 diiodo propane which is also an organic compound.
Therefore, when oxetane is heated in excess amount of concentrated HI, the product formed is 1,3 diiodo propane.
The reaction is given in the image attached below.
The given question is incomplete and the completed question is given below.
Draw the structural formula(s) for the organic product(s) formed when the following compound (OXETANE) is heated at reflux in an excess of concentrated (HI) .
Learn more about reflux from the link given below.
https://brainly.com/question/29484768
#SPJ4
If a precipitation reaction occurs, what will be the products of the unbalanced
reaction shown below?
Pb(NO3)2(aq) + K₂(SO4)(aq) →
Solubility Table
A. PbSO4(s) + KNO3(s)
B. PbSO4(aq) + KNO3(s)
C. No precipitate will form.
D. PbSO4(s) + KNO3(aq)
The products of the reaction are PbSO4(s) + KNO3(aq)
How does a precipitate form in a reaction?A precipitate is a solid that forms and separates out of a solution as the result of a chemical reaction. Precipitation reactions occur when two solutions containing ions are mixed together and the resulting mixture is no longer able to hold the ions in solution, causing them to form an insoluble solid.
In order to predict whether a precipitate will form or not, the solubility rules can be used to determine if a compound is soluble or insoluble in a particular solution. If the resulting compound is insoluble, a precipitate will form.
Learn more about precipitate:https://brainly.com/question/18109776
#SPJ1
hich are characteristics of photosynthesis? (Select all that apply.)
Plants use this process to make their food.
It provides the energy that we obtain from our food.
It takes place in the flower of a plant.
Oxygen is provided to animals from this process.
Answer:
Explanation:
A, B, D not C. It takes place in the leaves
An aqueous KNO3 solution is made using 70.5g of KNO3 diluted to a total solution volume of 1.97 L .
Calculate the molarity of the solution. (assume a density of 1.05 g/mL for the solution)
Calculate the molality of the solution.
Calculate the mass percent of the solution.
molar mass of KNO3 = 39.1 g/mol (K) + 14.0 g/mol (N) + 3x16.0 g/mol (O)
= 101.1 g/mol
moles of KNO3 = 70.5 g / 101.1 g/mol
= 0.697 mol
Next, calculate the volume of the solution in liters:volume of solution = mass of solution / density of solutionmass of solution = mass of KNO3 + mass of water
= 70.5 g + (1.97 L x 1.05 g/mL)
= 70.5 g + 2.067 g = 72.567 g
volume of solution = 72.567 g / 1.05 g/mL
= 69.105 L
Finally, calculate the molarity:Molarity = 0.697 mol / 69.105 L
= 0.0101 M
Molality:Molality = moles of solute / mass of solvent in kgAssuming the mass of the solute (KNO3) does not significantly affect the mass of the solution, we can use the same mass of solution as before:mass of solvent = mass of solution - mass of solute = 72.567 g - 70.5 g
= 2.067 g
Converting to kg:mass of solvent = 2.067 g / 1000 g/kg
= 0.002067 kg
Molality = 0.697 mol / 0.002067 kg
= 337.2 mol/kg
Mass percent:Mass percent = (mass of solute / mass of solution) x 100%mass of solute = 70.5 gmass of solution = 72.567 gMass percent = (70.5 g / 72.567 g) x 100%
= 97.16%
Learn more about molarity on
https://brainly.com/question/8732513
#SPJ1
in this experiment, you will be given approximately 1 gram each of acetanilide. draw the structure of the compound and describe the properties that make the solvent a good recrystallization solvent.
Acetanilide is an organic compound with the chemical formula C8H9NO. Its structure consists of a phenyl group attached to an amino group and a carbonyl group.
What is Recrystallization Solvent?
It involves dissolving a solid compound in a suitable solvent at high temperature, and then allowing it to cool down slowly to form pure crystals. The choice of solvent is crucial in the recrystallization process, as the solvent must be able to dissolve the solid compound at high temperature but not at low temperature, which would lead to the formation of pure crystals.
Acetanilide is a polar organic compound and is typically soluble in organic solvents such as hot ethanol, hot methanol, and hot water. These solvents are good recrystallization solvents for acetanilide because they can dissolve it at elevated temperatures, and upon cooling, the solubility of acetanilide decreases, leading to its precipitation and crystallization. The solvents are also able to dissolve impurities that might be present in the sample, so that the impurities remain in solution while the pure acetanilide crystals are formed upon cooling. Additionally, these solvents are relatively non-toxic, making them safe to use in a laboratory setting.
Learn more about Recrystallization Solvent from given link
https://brainly.com/question/13793982
#SPJ4
Managing a salt-water aquarium. A tank at the New Jersey State Aquarium has a volume of 2.9 million liters.' Bacteria are used to remove nitrate that would otherwise build up to toxic levels. Aquarium water is first pumped into a 2 700-L deaeration tank containing bacteria that consume 02 in the presence of added methanol: Bacteria 2CH3OH + 302 2002 + 4H20 (1) Methanol Anoxic (deoxygenated) water from the deaeration tank flows into a 1 500-L denitrification reactor containing colonies of Pseudomonas bacteria in a porous medium. Methanol is injected continuously and nitrate is converted into nitrite and then into nitrogen: Bacteria 3NO3 + CH3OH → 3NO2 + CO2 + 2H20 (2) Nitrate nitrite Bacteria 2NOZ + CH3OH → N2 + CO2 + H2O + 20H (3) (a) Deaeration can be thought of as a slow, bacteria-mediated titra- tion of O2 by CH3OH. The concentration of O2 in seawater at 24°C is 220 MM. How many liters of CH3OH (FM 32.04, density = 0.791 g/mL) are required by Reaction 1 for 2.9 million liters of aquarium water? (b) Write the net reaction showing nitrate plus methanol going to nitrogen. How many liters of CH3OH are required by the net reaction for 2.9 million liters of aquarium water with a nitrate concentration of 8 100 uM? (c) In addition to consuming methanol for Reactions 1 through 3, the bacteria require 30% more methanol for their own growth. What is the total volume of methanol required to denitrify 2.9 million liters of aquarium water?
A)17,300 L liters of CH3OH (FM 32.04, density = 0.791 g/mL) are required by Reaction 1 for 2.9 million liters of aquarium water.
B)192L liters of CH3OH are required by the net reaction for 2.9 million liters of aquarium water with a nitrate concentration of 8 100 uM.
C)The total volume of methanol required to denitrify 2.9 million liters of aquarium water is 22,496 L.
(a) To calculate the amount of CH3OH required for Reaction 1, we need to first determine the amount of O2 in 2.9 million liters of aquarium water.
Concentration of O2 in seawater = 220 mM
Volume of aquarium water = 2.9 million L
Amount of O2 in aquarium water = concentration x volume = 220 mM x 2.9 million L = 6.38 x 10^8 mmol
From the balanced chemical equation for Reaction 1, we see that 3 moles of O2 react with 2 moles of CH3OH. Therefore, the number of moles of CH3OH required is:
(2/3) x (6.38 x 10^8 mmol O2) = 4.25 x 10^8 mmol CH3OH
To convert this to volume, we need to use the density of CH3OH:
density = 0.791 g/mL
molar mass of CH3OH = 32.04 g/mol
volume of CH3OH = (4.25 x 10^8 mmol) x (32.04 g/mol) / (0.791 g/mL) = 1.73 x 10^7 mL = 17,300 L
(b) The net reaction for denitrification is:
5NO3- + CH3OH + 4H+ → N2 + 3CO2 + 7H2O
From the balanced chemical equation, we see that 1 mole of CH3OH is required for every 5 moles of NO3-. The concentration of nitrate in the aquarium water is 8,100 uM, which is equivalent to 8.1 mM.
Number of moles of nitrate in aquarium water = concentration x volume = 8.1 mM x 2.9 million L = 2.35 x 10^7 mmol
Number of moles of CH3OH required = (1/5) x (2.35 x 10^7 mmol) = 4.7 x 10^6 mmol
To convert this to volume, we use the same calculation as in part (a):
volume of CH3OH = (4.7 x 10^6 mmol) x (32.04 g/mol) / (0.791 g/mL) = 1.92 x 10^5 mL = 192 L
(c) The bacteria require 30% more methanol for their own growth, which means we need to add an additional 30% of the methanol required for Reactions 1-3.
Total volume of methanol required = volume from part (a) + volume from part (b) + 0.3 x (volume from part (b))
Total volume of methanol required = 17,300 L + 192 L + 0.3 x 192 L = 22,496 L
Therefore, the total volume of methanol required to denitrify 2.9 million liters of aquarium water is 22,496 L.
To know more about methanol here
https://brainly.com/question/28864629
#SPJ4
If the normal, undisturbed position of the wave is at 0 on the diagram below, what is the amplitude of Wave A?
20 m
40 m
10 m
5 m
5m is the amplitude of Wave A.
What is amplitude ?
A wave's amplitude is the separation between its starting point and its maximum displacement. Frequency is the quantity of waves traveling by a certain place each second. Period is the amount of time it takes for one wave cycle to finish.
What is wave ?
An energy-conducting disturbance in a medium known as a wave is one that does not involve any net particle motion. It could manifest as elasto-deformation, a shift in pressure, electric or magnetic intensity, electric potential, or temperature.
Therefore, 5m is the amplitude of Wave A.
Learn more about amplitude from the given link.
https://brainly.com/question/3613222
#SPJ1
bonding is similar to ionic bonding, except there are no high-electronegativity atoms present to accept any electrons that the present atoms are willing to donate. bonds are responsible for binding atoms together within a molecule of propane, whereas bonds bind separate propane molecules together in a condensed state (liquid or crystal). bonds are the only primary bonds that are directionally dependent. Materials whose constituent particles are bound by bonding are generally expected to have the lowest melting temperatures. Choose and fill the blanks from the following options: (a) Covalent (b) Ionic (c) Van der Waals (d) Hydrogen (e) Metallic
bonds are the only primary bonds that are directionally dependent. Materials whose constituent particles are bound by bonding are generally expected to have the lowest melting temperatures
The correct options to fill in the blanks are is a)covalent bond.
• Bonding is similar to covalent bonding, except there are no high-electronegativity atoms present to accept any electrons that the present atoms are willing to donate.
• Covalent bonds are responsible for binding atoms together within a molecule of propane, whereas van der Waals bonds bind separate propane molecules together in a condensed state (liquid or crystal).
• Covalent bonds are the only primary bonds that are directionally dependent.
• Materials whose constituent particles are bound by metallic bonding are generally expected to have the lowest melting temperatures.
Learn more about covalent bond here:
https://brainly.com/question/19382448
#SPJ4
Determine the mechanism and product for the given reaction by adding atoms, bonds, nonbonding electron pairs, and curved arrows. Acid and water are added in the second step.
−→−−−−−−−−−−CH3CH2MgBrProduct
The final product is 1-butanol.
The given reaction is the addition of a Grignard reagent, CH₃CH₂MgBr, to a carbonyl compound.
The mechanism for the reaction is a nucleophilic addition. The mechanism can be broken down into three main steps:
Step 1: Nucleophilic attack
The carbon atom in the carbonyl group has a partial positive charge, making it an electrophile. The carbon atom in the Grignard reagent has a partial negative charge, making it a nucleophile. The nucleophilic carbon attacks the electrophilic carbon of the carbonyl group, forming a tetrahedral intermediate.
H
|
H₃C C O
|
CH₃
-
|
CH₃CH₂MgBr
Step 2: Protonation
The tetrahedral intermediate is unstable and collapses. In this step, an acid, such as H₃O⁺, protonates the oxygen atom, which forms an alcohol.
H
|
H₃C C OH
|
CH₃
-
|
CH3CH2MgBr + H3O+
Step 3: Deprotonation
In the final step, a base, such as water, removes a proton from the protonated alcohol to form the final product, which is a neutral alcohol.
H
|
H₃C C OH
|
CH₃
|
H
Learn more about nucleophilic addition here: https://brainly.com/question/28331583
#SPJ4
The particles shown represent a proposed two-step mechanism for the destruction of ozone (O3) in the upper atmosphere. Based on the proposed mechanism, which of the following is the rate law expression for the destruction of O3?
The rate law expression for the destruction of O3 based on the proposed two-step mechanism is: rate = k[O3][NO]
This expression is derived from the proposed mechanism by identifying the rate-determining step (the slow step) and using the concentrations of the reactants involved in that step.
In this case, the slow step is the reaction between O3 and NO to form NO2 and O2. Therefore, the rate law expression is based on the concentrations of O3 and NO, and the rate constant k.
It is important to note that the rate law expression does not include the concentrations of the other reactants or products involved in the mechanism, as they are not involved in the rate-determining step.
Overall, the rate law expression for the destruction of O3 in the upper atmosphere based on the proposed two-step mechanism is rate = k[O3][NO].
To know more about destruction of O3, refer here:
https://brainly.com/question/30052644#
#SPJ11
What part of the plant traps the energy in the sunlight as the sunlight strikes the leaves?
roots
chlorophyll
stem
stomata
The chlorophyll in the leaves of a plant traps the energy in sunlight as the sunlight strikes the leaves. option B is the correct answer.
What is Chlorophyll ?Chlorophyll is a green pigment found in chloroplasts within plant cells, and it is responsible for absorbing light energy and using it to power the process of photosynthesis. The other options listed (roots, stem, stomata) are important parts of a plant, but they do not directly trap energy from sunlight.
Chlorophyll helps in trapping solar radiation. It helps in the absorption and assimilation of minerals from the soil. It helps in the synthesis of carbohydrates that serves as food for the entire plant.
Learn more about Chlorophyll on
https://brainly.com/question/13500580
#SPJ1
Answer:b
Explanation:
enter all allowable magnetic quantum numbers for each of the principal and angular momentum quantum number combinations given below.
For principal quantum number n = 1, l = 0 and m = 0.
For n = 2, l= 0, 1 and m = -1,0,1.
For n = 3, l = 0,1,2 and m = -2,-1,0,1,2
The magnetic quantum number (m) is one of the four quantum numbers used to describe the unique state of an electron in an atom. It goes from -l to +l.
a. For n=1 and l=0, the only allowable magnetic quantum number is 0.
b. For n=2 and l=0, the only allowable magnetic quantum number is 0.
c. For n=2 and l=1, the allowable magnetic quantum numbers are -1, 0, and 1.
d. For n=3 and l=0, the only allowable magnetic quantum number is 0.
e. For n=3 and l=1, the allowable magnetic quantum numbers are -1, 0, and 1.
f. For n=3 and l=2, the allowable magnetic quantum numbers are -2, -1, 0, 1, and 2.
To know more about the magnetic quantum numbers, here
brainly.com/question/14920144
#SPJ4
--The complete question is, Enter all allowable magnetic quantum numbers for each of the principal and angular momentum quantum number combinations given below.
a. n= 1, l =0
b. n =2 , l = 0
c. n =2, l =1
d. n =3, l =0
e. n =3, l =1
f. n =3, l =2--