The percent fuel efficiency of the car which has gasoline is about 14.8%.
What is Percent fuel efficiency?
Fuel efficiency of the vehicle or an engine measures the distance which a motor vehicle can travel on a single gallon of the gas or fuel. As a result of this, boosting the efficiency of these vehicles can also help them to limit the impact on the climate change.
Energy density of gasoline = 122.8 mega joules per gallon
Fuel economy of the car = 35 miles per gallon
Energy exerted per mile = 0.877 mega joules
Percent fuel efficiency = Energy output of car/ Energy input of car × 100
Where, Energy input of car = Energy density of gasoline × Number of gallons of gasoline used
Energy input of car = 122.8 mega joules/gallon × 1 gallon/ 35 miles × 1 mile/ 1.60934 kilometers× 1.60934 kilojoules/ mega joule
Energy input of car = 4.45 mega joules per kilometer
Energy output of car = Energy exerted per mile × Number of miles traveled
Energy output of car = 0.877 mega joules per mile × 35 miles
Energy output of car = 30.8 mega joules
Percent fuel efficiency = 30.8 mega joules/4.45 mega joules × 100
Percent fuel efficiency = 14.8%
Therefore, percent fuel efficiency of the car is 14.8%.
Learn more about Percent fuel efficiency here:
https://brainly.com/question/14366094
#SPJ11
matches have the potential to light on fire, but they will not do so without sufficient activation energy. explain what activation energy means and what type of activation energy the matches need.
Activation energy is the minimum energy that reactants must summon in other to become products during reactions.
What is activation energy?Activation energy is the minimum amount of energy required for a chemical reaction to occur. It is the energy barrier that must be overcome to start a chemical reaction. In order for a match to light on fire, it needs to be exposed to enough activation energy to initiate the chemical reaction between the match head and the striking surface.
When the match head is struck against the rough surface of the matchbox, friction generates heat, which provides the activation energy necessary to ignite the match.
The heat generated by friction between the match head and the striking surface provides enough activation energy to initiate a chemical reaction between the chemicals in the match head and the oxygen in the air. This chemical reaction produces heat and a flame, which can then be used to light a candle, stove, or other combustible material.
More on activation energy can be found here: https://brainly.com/question/11334504
#SPJ1
what quantities are conserved for a comet orbiting the sun?view available hint(s)for part chint 1for part c. what quantities are usually conservedwhat quantities are conserved for a comet orbiting the sun?speedtotal mechanical energykinetic energyangular momentum with respect to the center of the ellipseaccelerationgravitational potential energyangular speedlinear momentumangular momentum with respect to the sun
The quantities that are usually conserved for a comet orbiting the sun are:
Speed: The speed of a comet remains constant unless it is acted on by an outside force.
Total Mechanical Energy: The sum of the kinetic and potential energies of a comet remain constant in a closed system.
Kinetic Energy: The energy of a comet due to its motion.
Angular Momentum with Respect to the Center of the Ellipse: The angular momentum of a comet with respect to the center of its orbit remains constant.
Acceleration: The acceleration of a comet is zero unless acted upon by a force.
Gravitational Potential Energy: The potential energy of a comet due to its gravitational attraction to the sun remains constant.
Angular Speed: The angular speed of a comet remains constant unless it is acted upon by a force.
Linear Momentum: The momentum of a comet is conserved, meaning that its momentum remains the same unless acted upon by a force.
Angular Momentum with Respect to the Sun: The angular momentum of a comet with respect to the sun remains constant.
for such more questions on Angular Momentum
https://brainly.com/question/4126751
#SPJ11
A 4.00 g bullet is fired horizontally into a 1.20 kg wooden block resting on a horizontal surface. The coefficient of kinetic friction between block and surface is 0.20. The bullet remains embedded in the block, which is observed to slide 0.390 m along the surface before stopping.
What was the initial speed of the bullet? Express your answer with the appropriate units.
The initial speed of the bullet is 0.390 m/s.
It can be determined using the equations of motion and conservation of momentum. First, we will calculate the initial momentum of the bullet-block system.
Momentum is defined as mass multiplied by velocity, so the initial momentum of the bullet is equal to its mass (4.00 g) multiplied by its initial velocity (v). The momentum of the bullet-block system is then equal to the mass of the bullet multiplied by its initial velocity, plus the mass of the block multiplied by its initial velocity (0 m/s):
Momentum = mbullet * v + mblock * 0
Momentum = (4.00 g) * v + (1.20 kg) * 0
Using the equations of motion and the fact that the block slides a distance of 0.390 m before stopping, we can calculate the final momentum of the system. The final momentum of the bullet-block system is equal to the mass of the bullet multiplied by its final velocity (0 m/s), plus the mass of the block multiplied by its final velocity:
Final Momentum = mbullet * 0 + mblock * vblock
Final Momentum = (4.00 g) * 0 + (1.20 kg) * (0.390 m/s)
Conservation of momentum tells us that the initial momentum of the bullet-block system must be equal to the final momentum of the system. By setting the initial and final momentum equations equal to each other and solving for v, we can determine the initial velocity of the bullet:
(4.00 g) * v + (1.20 kg) * 0 = (4.00 g) * 0 + (1.20 kg) * (0.390 m/s)
v = 0.390 m/s
Therefore, the initial speed of the bullet is 0.390 m/s.
To know more about speed, refer here:
https://brainly.com/question/30462853#
SPJ11#
A barber wants to set up a salon in a room measuring length 3m by 3m he has a simple wooden chair,three large mirrors & a bulb. Using the knowledge of shadows & reflection advise the barber on how to arrenge a good saloon using the only items he has
Here are some ideas for setting up the barber's salon based on the size of the space and the products available: The wooden chair should be positioned in the middle of the space, facing a wall.
The barber's workspace will be this. The room's other three walls should be covered with the three enormous mirrors. This will give the impression that there is more space present and enlarge the room. The mirrors should be angled to reflect both the client in the chair and the barber's work area. Over the chair, suspend the lightbulb from the ceiling. The barber salon will be able to operate in enough lighting thanks to this.The wooden chair should be positioned in the middle of the space, The barber can set up a white sheet or a reflecting surface to improve illumination even further.
learn more about salon here:
https://brainly.com/question/15582651
#SPJ
What do the areas labeled x, y, and z represent? constructive interference in which waves cancel each other out constructive interference in which waves strengthen each other destructive interference in which waves cancel each other out destructive interference in which waves strengthen each other
The correct option is B, the areas labeled X, Y, and Z represent constructive interference in which waves strengthen each other.
Interference is a phenomenon that occurs when two or more waves interact with each other. In physics, waves can be described as a disturbance that travels through a medium, such as water or air. When two waves meet, they can either reinforce or cancel each other out, depending on their amplitudes and phases.
Constructive interference occurs when the peaks of two waves coincide, creating a larger amplitude than either wave alone. Destructive interference occurs when the peak of one wave coincides with the trough of another, resulting in a cancellation of the waves. Interference is a fundamental concept in many areas of physics, including optics, acoustics, and electromagnetism.
To learn more about Interference visit here:
brainly.com/question/16098226
#SPJ4
Complete Question:
The diagram shows monochromatic light passing through two openings.
What do the areas labeled X, Y, and Z represent?
A). constructive interference in which waves cancel each other out
B). constructive interference in which waves strengthen each other
C). destructive interference in which waves cancel each other out
D). destructive interference in which waves strengthen each other
amanda weighs about 600 n on earth, but would only weigh about 100 n on the moon. which best explains why amanda would weigh less on the moon than on earth? A. the mass of the moon is less than that of earth, therefore it has a weaker gravitational force. B. the circumference of the moon is smaller than earth, therefore it has less gravity. C. the pull from the gravity from earth decreases the pull of gravity from the moon. D. the lack of air pressure on the moon weakens the gravitational force of the moon.
Option A is the correct answer. The mass of the moon is less than that of earth, therefore it has a weaker gravitational force.
The correct option that explains why Amanda would weigh less on the moon than on earth is "A. the mass of the moon is less than that of the earth, therefore it has a weaker gravitational force." This is because weight is the result of the gravitational force that acts on an object, which is determined by both the mass of the object and the gravitational force acting on it. Therefore, the weight of an object varies depending on the mass and gravity.
The gravity of an object is the force that attracts it towards the center of the earth or the celestial object. The amount of gravity an object has depends on its mass and the mass of the object that it is attracting. The moon has a smaller mass than the earth, which means that it has a weaker gravitational force.
Consequently, the pull of gravity on the moon is weaker than on earth. The weight of Amanda is less because pull of gravity on the moon is weaker than on earth. Therefore, option A is the correct answer.
Learn more about "gravity, weight and mass" at : https://brainly.com/question/2124323
#SPJ11
After You Read
1. Give an example in which the distance you travel is different from your
displacement.
The example in which the distance you travel is different from your
displacement will be "Suppose a person starts at point A and walks 5 meters to point B, and then turns around and walks back to point A, covering another 5 meters. The distance traveled by the person is the total length of the path traveled, which is 10 meters (5 meters + 5 meters).
However, the displacement of the person is the change in position from the starting point to the ending point, which is zero. So the distance traveled is different from the displacement, as the person ends up at the same position where they started, despite covering a total distance of 10 meters.
What is displacement?Displacement is a verb that denotes movement or displacement of an object. The definition of displacement is the modification of an object's position.
The term "displacement" refers to a shift in an object's position. It is a vector quantity with a magnitude and direction. The symbol for it is an arrow pointing from the initial location to the ending place. For instance, if an object shifts from location A to position B, its position changes.
Learn more about displacement on:
https://brainly.com/question/14422259
#SPJ1
what force, in newtons, must be supplied by the elevator's cable to produce an acceleration of 0.85 m/s2 upwards against a 180-n frictional force?
Force in newtons that must be supplied by the elevator's cable to produce an acceleration of 0.85 m/s² upwards against a 180N frictional force is 944 N.
What is force?Force is a vector quantity that has both magnitude and direction. A force is necessary to create an acceleration in an object's movement. Force is calculated by multiplying mass by acceleration.
Acceleration of the elevator, a = 0.85 m/s²
Frictional force, Ff = 180 N
Equation of motion, F = ma (Where F is the force applied, m is the mass of the object, and a is the acceleration produced)
Since the elevator is moving upwards, the direction of the force is upward. The equation of motion becomes:
F = ma + Ff = m(0.85 m/s²) + 180 N
The weight of the elevator is equivalent to the force needed to lift it up. So, the force needed is equivalent to the weight of the elevator (mg).
For the equation of motion above, the mass of the elevator is canceled out leaving the force as the only unknown. F = (0.85 m/s²) × 1000 kg × 1 N/kg + 180 N = 850 N + 180 N = 1030 N.
Therefore, the force in newtons that must be supplied by the elevator's cable to produce an acceleration of 0.85 m/s² upwards against a 180 N frictional force is 944 N.
Read more about the force here:
https://brainly.com/question/12785175
#SPJ11
assume a single-issue pipeline. show how the loop would look both unscheduled by the compiler and after compiler scheduling for both floating-point operation and branch delays, including any stalls or idle clock cycles. what is the execution time (in cycles) per element of the result vector, y, unscheduled and scheduled? how much faster must the clock be for proces- sor hardware alone to match the performance improvement achieved by the scheduling compiler? (neglect any possible effects of increased clock speed on memory system performance.)
Assuming a single-issue pipeline, the loop would look as follows when unscheduled by the compiler:
To know more compiler schedules about refer here: https://brainly.com/question/30008837#
#SPJ11
(a) how many kilometers does light traverse in 1 ly? km (b) what is the speed of light c in terms of ly per year. ly/y (c) express your answer from (b) in terms of feet per nanosecond. ft/ns
a) Light traverses approximately 9.461 × 10^12 kilometers in 1 light-year
.b) The speed of light in terms of ly per year is 1 ly/y.c) 1 light-year equals 5.8785 × 10^12 miles. 1 mile is equal to 5,280 feet.
Therefore, 1 light-year is equal to 31.0688 × 10^12 feet. A nanosecond is equal to one billionth of a second (1/1,000,000,000 second). Therefore, 1 second is equal to 1 × 10^9 nanoseconds. Speed is equal to distance divided by time.
Therefore, Speed of light in feet per nanosecond = (31.0688 × 10^12 feet) / (1 year × 365 days/year × 24 hours/day × 3600 seconds/hour × 1 × 10^9 nanoseconds/second) = 1.005 × 10^5 feet per nanosecond (approximately).
for such more questions on speed of light
https://brainly.com/question/100983
#SPJ11
A book is sitting on a shelf that is 3. 0 meters off the ground. Kinetic energy is found using the formula 1/2 times mass times speed. Potential energy is found by taking mass times g times height, with g as the constant, 9. 8 m/s squared. What is needed to determine the mechanical energy used to move this book?
The required mechanical energy used to move this book is calculated by the summation of kinetic energy and potential energy.
Mechanical energy M.E is constant in a system that has only gravitational forces or in an otherwise idealised system.
Given that, the method for calculating kinetic energy K.E is,
K.E = 1/2 × m × v²
where,
m is mass
v is velocity
Potential energy P.E is given as mass times g times height, with g as a constant 9.8 m/s².
P.E = m × g × h
where,
m is mass
g is gravity
h is height
Potential and kinetic energies combine to form mechanical energy.
So, mathematically,
M.E = K.E + P.E
"M.E = 1/2 × m × v² + m × g × h"
To know more about energy:
https://brainly.com/question/13864172
#SPJ4
You kind of answered my question, I was wondering an object accelerates in the direction of the net force always but what is the opposite and equal reaction, since it is accelerating it is an unbalanced force so what is the equal and opposite reaction?
Answer:
According to Newton's Third Law of Motion, for every action, there is an equal and opposite reaction. When an object experiences an unbalanced force in a certain direction, it will accelerate in that direction. The equal and opposite reaction to this force is the force that the object exerts on the other object causing the original force. For example, if you push on a box with a force of 10 Newtons to the right, the box will experience an unbalanced force in the right direction and accelerate to the right. The equal and opposite reaction to your push is the box pushing back on you with a force of 10 Newtons in the left direction. The force you exerted on the box and the force the box exerted back on you are equal in magnitude and opposite in direction.
Does this help?
Three identical conducting spheres are charged as follows. Sphere A is positively charged, sphere B is negatively charged with a different magnitude of net charge than that of sphere A, and sphere C is uncharged. Spheres A and B are momentarily touched together and separated, then spheres B and C are briefly touched together and separated. After that series of processes is completed, which of the following interactions, if any, can be used as evidence to determine whether sphere A or sphere B had the initially larger magnitude of charge? A Sphere C is repelled from sphere A. B Sphere C is repelled from sphere B. Sphere A is repelled from sphere B. D It cannot be determined from observing whether the spheres repel, because they all have the same sign of charge.
The answer is C. Sphere A is repelled from sphere B
Step by step explanation:
The question is asking which of the interactions between sphere A, B, and C can be used as evidence to determine which one had the initially larger magnitude of charge. This is because if sphere A has a larger magnitude of charge than sphere B, then when spheres A and B are touched and separated, the charge of sphere A would be transferred to sphere B, causing a conduction of charge.
This means that after the processes are completed, the charge of sphere A and B will have reversed - meaning that sphere A will now have the same, but opposite sign of charge as sphere B. As a result, when sphere A and B are close to each other, their charges will repel, so Sphere A is repelled from sphere B.
Learn more about "conduction and charge" at : https://brainly.com/question/893656
#SPJ11
what is the current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds
The current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds is 0.0504 amperes
Current calculation.
The current in a conductor is defined as the rate at which electric charge flows through it. The unit of current is amperes (A), which is defined as coulombs per second. One coulomb is equal to the charge on 6.24 × 10^18 electrons.
Given that 3.15 × 10^18 electrons pass a given point in the conductor in 10 seconds, we can find the charge that flows through the point as follows:
Number of electrons = 3.15 × 10^18
Charge on one electron = 1.6 × 10^-19 coulombs
Total charge = Number of electrons × Charge on one electron
Total charge = 3.15 × 10^18 × 1.6 × 10^-19
Total charge = 0.504 coulombs
The current is the rate of flow of charge, so we can find it by dividing the total charge by the time taken:
Current = Total charge ÷ Time taken
Current = 0.504 coulombs ÷ 10 seconds
Current = 0.0504 amperes (A)
Therefore, the current in the conductor is 0.0504 amperes, or 50.4 milliamperes (mA).
Learn more about current below.
https://brainly.com/question/24858512
#SPJ1
A uniform meter stick is balanced at its midpoint with a single support. A 50 N weight is suspended at the 30 cm mark. At what point must a 20 N weight be hung to balance the system?
The 20 N weight must be hung at the 70 cm mark to balance the system.
To find the location of the 20 N weight, we can use the principle of moments, which states that the sum of the clockwise moments about a point must equal the sum of the counterclockwise moments about the same point in order for the object to be in equilibrium.
Since the meter stick is balanced at its midpoint, the point of rotation is at the 50 cm mark. Let x be the distance from the 50 cm mark to the location where the 20 N weight is hung. Then, the clockwise moment due to the 50 N weight at the 30 cm mark is:
(50 N)(20 cm) = 1000 Ncm
And the counterclockwise moment due to the 20 N weight at the x cm mark is:
(20 N)(x - 50 cm)
To balance the system, these two moments must be equal:
1000 Ncm = (20 N)(x - 50 cm)
Solving for x, we get:
x - 50 cm = 50 cm
x = 100 cm
Therefore, the 20 N weight must be hung at the 70 cm mark (100 cm - 30 cm) to balance the system.
For more similar questions on mechanics and physics:
brainly.com/question/13399673
#SPJ11
a block with a mass of 10 kg connected to a spring oscillates back and forth with an amplitude of 2 m. what is the approximate period of the block if it has a speed of 4 m/s when it passes through its equilibrium point?
By Conservation of Mechanical Energy, the energy of the block is the same throughout the motion. At the amplitude, the block has potential energy [tex]U=1/2 kA^{2}[/tex] and zero kinetic energy. At the equilibrium position, the block has kinetic energy and zero potential energy. Applying the Conservation of Mechanical Energy to these two points in the motion yields.
[tex]K[tex]1/2 kA^{2} + 0 = 0 + 1/2mv^{2} \\kA^{2} = mv^{2} \\k = mv^{2}/A^{2} = 10kg*(4m/s)^{2} = 40kg/s^{2}[/tex] 1/2 mv^{2}[/tex]
The block with a mass of 10 kg connected to a spring oscillates back and forth with an amplitude of 2 m and a speed of 4 m/s when it passes through its equilibrium point. The approximate period of the block is calculated using the equation T = 2π*√(m/k), where m is the mass and k is the spring constant. We can calculate the approximate period using the given information as
[tex]T = 2π*√(10/k)\\T = 2π*√(10kg/40kg/s^{2} )\\T = 3 sec[/tex],
For more information regarding this topic, you can check the below link
https://brainly.com/question/12622728
#SPJ11
Which frequency of light has the smallest (shortest) wavelength? Select the correct answer below; 10 GHz 10 MHz 10 Hz 1 Hz
The frequency of light that has the smallest (shortest) wavelength is 10 GHz. Wavelength and frequency are inversely proportional; that is, when the frequency is higher, the wavelength is shorter. Thus, option a is correct.
Frequency is the number of occurrences of a repeated event per unit of time. It is represented by the symbol f, and it is measured in hertz (Hz). The SI unit hertz is named after Heinrich Rudolf Hertz, a physicist from Germany.
How is wavelength related to frequency?Wavelength and frequency are inversely proportional, meaning that when the frequency of a wave is high, its wavelength is short. This can be seen in the formula that relates wavelength to frequency and the speed of light:
c = λf, where c is the speed of light, λ is the wavelength, and f is the frequency.
As a result, a light wave with a higher frequency, such as gamma rays, has a shorter wavelength, whereas a light wave with a lower frequency, such as radio waves, has a longer wavelength.
In contrast to wavelength, which is measured in meters, frequency is measured in gigahertz (GHz).
Therefore, as the frequency of a wave increases, its wavelength decreases. Thus, option a is correct.
Learn more about the Frequency of light here:
https://brainly.com/question/29213586
#SPJ11
"Radioactive decay is a random process but we can still make predictions about it" Explain this statement
Answer:
Radioactive decay is determined by quantum mechanics — which is inherently probabilistic. So it's impossible to work out when any particular atom will decay, but we can make predictions based on the statistical behaviour of large numbers of atoms.
pls mark me brainliest
which phenomenon causes precipitation to reach earth?
"Precipitation occurs due to condensation of water molecules in the air into droplets and they fall to the ground due to gravity."
One of the stages of the water cycle is precipitation. Clouds are areas of the sky with enough water content for drops to condense, and they are where precipitation originates. Therefore, precipitation follows mist. Although clouds are the source of all precipitation, not all clouds generate precipitation.
When cloud droplets or crystals become too dense to continue floating in the atmosphere, precipitation starts to descend from the clouds. If droplets do not become sufficiently dense, precipitation will not occur, and if the cloud is sufficiently heated by the Sun, it may even disperse. But for there to be a place for precipitation to come from, clouds do need to develop.
To know more about precipitation:
https://brainly.com/question/1159753
#SPJ4
a 88.5 kg skater moving initially at 2.40 m/s on rough horizontal ice comes to rest uniformly in 3.52 s due to friction from the ice.what force does friction exert on the skater?
The force of friction exerted by the ice on the skater is -60.2 N, directed in the opposite direction of the motion of the skater.
To calculate the force of friction, we will use Newton's second law of motion that is F = m * a. The skater is moving initially at a velocity of 2.40 m/s and comes to rest in 3.52 s due to friction from the ice. The weight of the skater is 88.5 kg.
The acceleration of the skater can be calculated by using the formula of motion that is v = u + at. v is the final velocity, u is the initial velocity, a is the acceleration, and t is time taken. Here, u = 2.40 m/s, v = 0 (as the skater comes to rest), and t = 3.52 s.
The acceleration of the skater is calculated as follows;
a = (v - u) / t = (0 - 2.40) / 3.52 = -0.682 m/s²The force of friction can be calculated by multiplying the acceleration by mass as follows:
F = m * a = 88.5 * (-0.682) = -60.2 NLearn more about friction: https://brainly.com/question/24338873
#SPJ11
An object is 29cm away from a concave mirror's surface along the principal axis.If the mirror's focal length is 9.50 cm, how far away is thecorresponding image?
a.12
b.14
c.29
d.36
The image's distance from the concave mirror's surface is 12 cm. The correct option is B.
How to calculate the distance of the image?A concave mirror is a mirror that has a reflective surface that curves inward like a part of a sphere. Concave mirrors are also known as "converging mirrors."When a ray of light falls on a concave mirror, the light rays converge at a point in front of the mirror.
This point is known as the focal point of the concave mirror. The distance between the focal point and the concave mirror's surface is referred to as the focal length of the concave mirror. It is negative for concave mirrors because they converge in light rays.
An object is 29 cm away from a concave mirror's surface along the principal axis. The mirror's focal length is 9.50 cm, so the image's distance from the mirror can be calculated using the mirror formula.
The mirror formula is:
1/v + 1/u = 1/f
where u is the object's distance from the mirror, v is the image's distance from the mirror, and f is the focal length of the mirror.
In this case, u = -29 cm, f = -9.5 cm, and we want to solve for v.
1/v + 1/-29 = 1/-9.5
Multiply both sides of the equation by
v x -29 x -9.5:-9.5v + -29(-9.5) = v(-29)(-9.5)285.5 = v(275.5)
v = -285.5/275.5
v ≈ -1.0378 cm
The negative sign indicates that the image is inverted, which is common for concave mirrors. The image is also closer to the mirror than the object, which is another characteristic of concave mirrors. The distance from the mirror's surface to the image is given by:-1.0378 - (-9.5) = 8.46 cm this is the same as 8.46 cm from the surface of the mirror.
Therefore, the image's distance from the concave mirror's surface is 12 cm. Option (a) 12 is correct.
To learn more about concave mirrors follow
https://brainly.com/question/3004256
#SPJ11
The black hole in M31. Measurements of star motions at the center of the Andromeda galaxy (M31) show that stars about 3 light-years from the center are orbiting at a speed of about 400 km/s. If these stars are orbiting a supermassive black hole, what would be its mass (in solar masses)?
The mass of the supermassive black hole is 2.8×10⁸ solar masses.
In order to calculate the mass of the supermassive black hole at the center of the Andromeda galaxy (M31), we can use the following formula:
GM = v²r
where, G is the gravitational constant, M is the mass of the black hole, v is the orbital speed of the stars, and r is the radius of the orbit of the stars from the center of the black hole.
It is given that v = 400 km/s, r = 3 light-years = 2.839×10¹⁶ meters, G = 6.67×10⁻¹¹ Nm²/kg².
We can convert the speed of the stars to meters per second:
v = 400 km/s = 4×10⁵ m/s
Now, substituting the values in the formula, we get:
GM = v²r
M = v²r/G
= (4×10⁵)²×(2.839×10¹⁶)/(6.67×10⁻¹¹)
= 2.8×10⁸ solar masses
Therefore, the mass of the supermassive black hole at the center of the Andromeda galaxy (M31) is 2.8×10⁸ solar masses.
Learn more about Black hole:
https://brainly.com/question/6037502
#SPJ11
lifting the weight without a pulley requires a force of 400 newtons over a distance of 4 meters. how do these values change when the pulley is applied? (1 point) responses
A. the force increases, while the distance decreases. B. both the force and the distance decrease. C. the force decreases, while the distance increases. D. both the force and the distance increase.
When the pulley is applied, the force decreases, while the distance increases. The correct option is C. Therefore, when a pulley is used, the force required to lift the weight decreases, while the distance over which the force is applied increases.
When a pulley is used to lift a weight, the force required to lift the weight is reduced, while the distance over which the force is applied is increased. The pulley system distributes the weight of the object across multiple strands of rope or cable, reducing the amount of force required to lift the object.
In this case, the force required to lift the weight decreases when a pulley is used, as the weight is supported by two segments of rope or cable, each bearing half the weight. Therefore, the force required is effectively halved.
On the other hand, the distance over which the force is applied increases when a pulley is used. This is because the rope or cable must be pulled twice as far as the distance that the weight is lifted, due to the nature of the pulley system. As a result, the distance over which the force is applied is effectively doubled.
Therefore, when a pulley is used, the force required to lift the weight decreases, while the distance over which the force is applied increases.
For more such questions on Force
https://brainly.com/question/15251816
#SPJ11
Given F1=800 N, F2=600N (a) Determine the support reaction forces at the smooth collar A. Ax= [ Select] . Ay= (Select) [Select] (b) Determine the support reaction moments at the smooth collar A. M(A) [Select] "Nim, M(A)y= (Select] Nim M(A)z= [Select] Nim. (c) Determine the normal reaction at the roller support B.B- [Select] N 0 m
a. The support reaction forces at the smooth collar A are Ax = 800 N and Ay = 600 N,
b. The support reaction moments at the smooth collar A are M(A)x = -1600Nm, M(A)y = 0Nm, and M(A)z = 400Nm
C. the normal reaction at the roller support B is B- = 600N.
The value of Ax = 800 N and Ay = 600 N , M(A)x = -1600Nm, M(A)y = 0Nm, and M(A)z = 400Nm B- = 600N.
The support reaction forces at the smooth collar A can be determined using equations of equilibrium:
F1 + F2 = Ax + Ay and F1x = Ax.
Therefore, Ax = 800 N and Ay = 600 N.
The support reaction moments at the smooth collar A can be determined using the moments equation of equilibrium: M(A)x + M(A)y + M(A)z = 0.
Substituting in the values for Ax and Ay, we can solve for the support reaction moments: M(A)x = -1600Nm, M(A)y = 0Nm, and M(A)z = 400Nm.
The normal reaction at the roller support B can be determined using equations of equilibrium:
F1 + F2 + B- = 0 and Ay = B-.
Therefore, B- = 600N.
In summary, the support reaction forces at the smooth collar A are Ax = 800 N and Ay = 600 N, the support reaction moments at the smooth collar A are M(A)x = -1600Nm, M(A)y = 0Nm, and M(A)z = 400Nm, and the normal reaction at the roller support B is B- = 600N.
To know more about reaction forces click on below link:
https://brainly.com/question/14853868#
#SPJ11
To demonstrate the ideas of electric current and resistivity the following experiment was conducted using a 10.0 m long 1.00 m diameter pipe. The pipe is connected to an air pump which produces high air pressure at one end. The other end of the pipe is open to the surrounding air, and the pump maintains a constant difference in air pressure between the two ends. Six hundred electrically charged ping pong balls are injected into the pipe with velocities that have random magnitudes and directions. Due to the difference in air pressure, the balls drift from the high pressure end of the pipe to the low pressure end at a speed of 2.00 cm/s. If every ping pong ball is given a charge of 6.00 microcoulombs, how much current flows through the pipe?
Solution:
First determine the total charge by multiplying 600 balls by 6.00 microC/ball. This yields 3600 μC.
Next, determine the time by dividing the distance by the speed (watch the units.), yielding 500 s.
Lastly, current is charge per unit time, so divide 3600 μC/500s to get 7.00 microamps.
= 7.00 microamps
The question asks how much current flows through the pipe when 600 ping pong balls with 6.00 microC of charge each are injected into the pipe and drift from the high-pressure end to the low-pressure end at a speed of 2.00 cm/s.
Using the formula for current (I = Q/t), where I is current, Q is charge, and t is time,
we can determine the current flowing through the pipe.
First, we need to determine the total charge by multiplying 600 balls by 6.00 microC/ball, yielding 3600 μC.
Next, determine the time by dividing the distance (10.0 m) by the speed (2.00 cm/s) to get 500 s. Lastly, current is the charge per unit time, so divide 3600 μC/500s to get 7.2 microamps.
Therefore, the amount of electric current flowing through the pipe is 7.2 microamps.
To learn more about current refer to: https://brainly.com/question/25922783
#SPJ11
suppose that you drop a solid iron ball and a hollow iron ball, both the exact same diameter, from the same height at the same time. aristotle would predict that
If you drop a solid iron ball and a hollow iron ball of the same diameter from the same height at the same time, Aristotle's prediction would be that the solid iron ball will fall faster than the hollow iron ball.
Aristotle and gravity lawAristotle, who lived in ancient Greece, believed that heavier objects would fall faster than lighter ones. This was a commonly held belief at the time, but it has since been proven incorrect through scientific experiments.
In reality, when dropped from the same height at the same time, both the solid iron ball and the hollow iron ball of the same diameter would fall at the same rate, neglecting air resistance. This is because the rate at which an object falls is determined by its mass and the force of gravity acting on it, which are the same for both balls.
This was first demonstrated by Galileo Galilei in the late 16th century through his famous experiment involving dropping objects from the Leaning Tower of Pisa. He showed that objects of different masses would fall at the same rate in a vacuum and that air resistance was the primary factor that caused objects to fall at different rates in the real world.
In summary, Aristotle would have predicted that the solid iron ball would fall faster than the hollow iron ball, but this prediction has been shown to be incorrect by scientific experiments.
More on Aristotle can be found here: https://brainly.com/question/5399979
#SPJ1
Does Life, evolutin On Earth Violate the Second Law of Thermodynamics?
Answer:
No, it doesn’t.
Explanation:
The second law of thermodynamics states that in a natural thermodynamic process, the sum of the entropies of the interacting thermodynamic systems increases. Equivalently, machines that spontaneously convert thermal energy into mechanical work are impossible.
If you combine milk and coffee, the entropy will rise until the mixture is entirely homogenous and you can no longer differentiate between the two substances. At that point, the mixture will be a single, dull hue.
But in the process of mixing up coffee, before it’s fully mixed together but after you have started mixing, you might notice some complex swirl patterns appear for a brief moment in the chaos before vanishing away.
That’s what human life is.
We’re not violating thermodynamics because if you take the system as a whole, including the sun and the earth, entropy is still increasing. The sun will eventually run out of fuel and die out. Eventually all suns will die out and the whole universe will be homogeneous and we will have heat death as the expanding universe rips complex atoms apart.
But there can be brief pockets of complexity within that system, that exists for a brief period of time, before eventually and inevitably fading away. It does not violate thermodynamics because entropy is still increasing in the system as a whole.
a block of mass 0.243 kg is placed on top of a light, vertical spring of force constant 4 975 n/m and pushed downward so that the spring is compressed by 0.092 m. after the block is released from rest, it travels upward and then leaves the spring. to what maximum height above the point of release does it rise? (round your answer to two decimal places.)
The maximum height above the point of release that the block rises to is 0.17 meters.
To solve this problem, we can use the conservation of energy principle, which states that the initial potential energy of the block and spring system is equal to the final kinetic energy of the block. The initial potential energy is given by the formula:
PEi = (1/2)kx^2
where k is the force constant of the spring, and x is the compression of the spring. Plugging in the values, we get:
PEi = (1/2)(4,975 N/m)(0.092 m)^2 = 20.20 J
The final kinetic energy of the block is given by the formula:
KEf = (1/2)mv^2
where m is the mass of the block, and v is the velocity of the block at the maximum height. Since the block comes to a stop at the maximum height, its final velocity is zero. Therefore, we can equate the initial potential energy to the final kinetic energy:
PEi = KEf
Solving for v, we get:
v = sqrt(2PEi/m) = sqrt(2(20.20 J)/(0.243 kg)) = 2.41 m/s
Now, we can use the conservation of mechanical energy principle to find the maximum height h that the block rises to:
PEi + KEi = PEf + KEf
where PEf = mgh and KEi = 0. Plugging in the values, we get:
mgh = PEi + KEf = 20.20 J
Solving for h, we get:
h = PEi/(mg) = (20.20 J)/(0.243 kg)(9.81 m/s^2) = 0.17 m
Therefore, the block rises to a maximum height of 0.17 meters above the point of release.
For more similar questions on energy and mechanics:
brainly.com/question/16971063
#SPJ11
Solve and check In the previous parts, you obtained the following equations using Newton's 2nd law and the constraint on the motion of the two blocks: m2a2x = T - m2g sin(θ), (1)
m1a1y = T - m1g, (2) and a2z = -a1y (3) Solve these equations to find a1y. Before you enter your answer, make sure it satisfies the special cases you already identified: - a1y = -g if m2 = 0 and - a1y = 0 if m1 = m2 and θ = π/2. Also make sure that your answer has dimensions of acceleration. Express a1y in terms of some or all of the variables m1, m2, θ, and g.
a1y = ____ ?
a1y in terms of some or all of the variables m1, m2, θ, and g is
a1y = (m2g sin(θ) - m1g) / m1 - m2a2x
What is Newton's 2nd law?In accordance with his second law, a force is equal to the change in momentum (defined as mass times velocity) per change in time. The definition of momentum is the product of the mass m and the velocity V of an object.
m2a2x = T - m2g sin(θ),
(1)m1a1y = T - m1g,
(2)a2z = -a1y (3)
On substitution of a2z = -a1y in (2):
m1(-a2z) = T - m1g
Therefore, -m1a1y = T - m1gOr,
m1a1y = m1g - T
On substitution of a2z = -a1y and
T = m2a2x + m2g sin(θ) in the above equation:
m1(-a2z) = m2a2x + m2g sin(θ) - m1g
Therefore, a1y = (m2g sin(θ) - m1g) / m1 - m2a2x
By solving this equation, the value of a1y.
a1y = -g
when m2 = 0a1y = 0
when m1 = m2 and θ = π/2.
The dimension of acceleration is m/s².
Thus, a1y in terms of m1, m2, θ, and g is given by
a1y = (m2g sin(θ) - m1g) / m1 - m2a2x
To know more about acceleration:
brainly.com/question/107797
#SPJ11
an electromagnetic wave is transporting energy in the positive y direction. at one point and one instant the magnetic field is in the positive x direction. the electric field at that point and instant points in the
Energy is being transported in the positive y direction by an electromagnetic wave. The magnetic field is in the positive x direction at one spot and one moment. At that precise moment, the electric field is oriented in the "negative z" direction.
The given electromagnetic wave is transporting energy in the positive y direction. At one point and one instant, the magnetic field is in the positive x direction. Now we have to find the direction of the electric field at that point and instant. According to the right-hand rule, when the magnetic field is directed towards the positive x-axis, the electric field will be directed downwards along the negative z-axis. Therefore, the electric field at that point and instant points in the negative z direction.
To know more about electromagnetic wave:https://brainly.com/question/75996
#SPJ11