If p(a)=0.07692, p(b)=0.25, and probability of a and b. =0.01923, what is probability of a or b. to four decimal places? select one.

Answers

Answer 1

Answer:

p(a) * p(b) = .01923

p(b) = .01923 / .07692 = .2500

Answer 2

The probability of a or b will be equal to 0.30769.

What is probability?

Probability is defined as the ratio of the number of favorable outcomes to the total number of outcomes in other words the probability is the number that shows the happening of the event.

The probability of the total sample points in A U B is P(A U B). The probabilities of sample points in A and B are now added together as P(A) + P(B). To get the total of probabilities in (A U B), which is P, we need to subtract once because we added the sample points in (A B) twice (A U B).

Given that p(a)=0.07692, p(b)=0.25, and probability of a and b. =0.01923. The probability will be calculated by using the formula below:-

P(A) = 0.07692

P(B)=0.25

P(A[tex]\cap[/tex]B) = 0.01923

P(AUB) = P(A) + P(B) - P(A[tex]\cap[/tex]B)

P(AUB) = 0.07692 + 0.25 - 0.01923

P(AUB) = 0.30769

Therefore, the probability of a or b will be equal to 0.30769.

To know more about probability follow

https://brainly.com/question/28025253

#SPJ2


Related Questions

a box is at rest on a slope with an angle of 40.0o to the horizontal. if the mass of the box is 10.0kg, what is the perpendicular component of the weight? 6.43n 75.1n 7.66n 63.0n

Answers

Therefore, the perpendicular component of the weight is 75.1N which is option B.

Perpendicular component calculation.

To determine the perpendicular component of the weight we must first find the perpendicular component of the slope surface.

Weight = mass * acceleration due to gravity.

Weight = 10 * 9.8

Weight = 98N

Perpendicular weight = weight * cos angle.

                               = 98 * cos 40°

Perpendicular weight is 75.1N.

Therefore, the perpendicular component of the weight is 75.1N.

Learn more about perpendicular component below.

https://brainly.com/question/30491683

#SPJ1

If a magnet is held stationary relative to the coil, how much emf is induced?.

Answers

If a magnet is held stationary relative to a coil, no electromotive force (emf) is induced in the coil, or the induced emf is zero.

The phenomenon of electromagnetic induction, which is responsible for the generation of emf in a coil, occurs when there is a relative motion between a magnetic field and the coil. When a magnetic field moves or changes relative to a coil, the magnetic field lines passing through the coil are altered, inducing an emf according to Faraday's law of electromagnetic induction.

However, if the magnet is held stationary relative to the coil, there is no relative motion between the magnetic field and the coil, and therefore no change in the magnetic field lines passing through the coil. As a result, no emf is induced in the coil.

In order to induce an emf in a stationary coil, there must be relative motion between the magnet and the coil, such as the magnet being moved towards or away from the coil, or the coil being moved through a magnetic field.

Learn more about electromotive force here:

https://brainly.com/question/31366996

#SPJ11

5. A rock, which weighs 1400 N in air, has an apparent weight of 900 N when submerged in fresh water (998 kg/m³). The volume of the rock is:
A) 0.14 m³ B) 0.50 m³ C) 0.90 m³ D) 5.1 x 102 m m³ E) 9.2 x 10 m³ 3

Answers

The volume of the rock is B. 0.050 m³

To solve this problem, we need to use the concept of buoyancy. When a rock is submerged in water, it displaces an amount of water equal to its volume. This displaced water exerts an upward buoyant force on the rock, which reduces its apparent weight.

We can use the formula for buoyant force: B = ρVg, where B is the buoyant force, ρ is the density of the fluid (fresh water in this case), V is the volume of the submerged object, and g is the acceleration due to gravity (9.8 m/s²).

From the given data, we know that the buoyant force on the rock is (1400 N - 900 N) = 500 N. Therefore, we can write:

500 N = (998 kg/m³)(V)(9.8 m/s²)

Solving for V, we get V = 0.0506 m³.

Therefore, the volume of the rock is 0.0506 m³, which is closest to 0.50 m³.

In summary, the apparent weight of a submerged object is reduced due to the upward buoyant force exerted by the displaced fluid. By using the formula for buoyant force, we can calculate the volume of the submerged object. Therefore, Option B is correct.

Know more about Buoyancy here:

https://brainly.com/question/12788506

#SPJ11

a negatively charged rod is brought close to an uncharged sphere. if the sphere is momentarily
earthed and then the rod is removed briefly explain what happens

Answers

The sphere will become negatively charged and attract positively charged objects due to the transfer of electrons from earth.

When the negatively charged rod is brought close to the uncharged sphere, the electrons in the sphere are repelled to one side, leaving the other side positively charged.

If the sphere is momentarily earthed, the excess electrons are transferred to the earth, leaving the sphere neutral.

When the rod is removed, the electrons that were initially repelled will move back towards the positively charged side of the sphere, making it negatively charged.

The sphere will then attract positively charged objects due to the imbalance of charges.

This is known as electrostatic induction, which is the process of charging an object by bringing it near a charged object without direct contact.

For more such questions on electrons, click on:

https://brainly.com/question/860094

#SPJ11

he energy of the decay products of a particular short-lived particle has an uncertainty of 1.1 mev. due to its short lifetime. What is the smallest lifetime it can have?

Answers

The smallest lifetime that the short-lived particle can have is approximately 2.02 x 10^-21 seconds.

The uncertainty principle states that there is a fundamental limit to how precisely certain pairs of physical properties of a particle, such as its energy and lifetime, can be known simultaneously. In this case, we can use the uncertainty principle to determine the smallest lifetime of a short-lived particle with an energy uncertainty of 1.1 MeV.

The uncertainty principle can be expressed as:

ΔE Δt >= h/4π

where ΔE is the energy uncertainty, Δt is the lifetime uncertainty, and h is Planck's constant.

Rearranging the equation, we get:

Δt >= h/4πΔE

Substituting the values, we get:

Δt >= (6.626 x 10^-34 J s) / (4π x 1.1 x 10^6 eV)

Converting the electron volts (eV) to joules (J), we get:

Δt >= (6.626 x 10^-34 J s) / (4π x 1.76 x 10^-13 J)

Δt >= 2.02 x 10^-21 s

For more question on particle click on

https://brainly.com/question/30685477

#SPJ11

The energy-time uncertainty principle states that the product of the uncertainty in energy and the uncertainty in time must be greater than or equal to Planck's constant divided by 4π. Mathematically, we can write:

ΔEΔt ≥ h/4π

where ΔE is the uncertainty in energy, Δt is the uncertainty in time, and h is Planck's constant.

In this problem, we are given that the uncertainty in energy is 1.1 MeV. To find the smallest lifetime, we need to find the maximum uncertainty in time that is consistent with this energy uncertainty. Therefore, we rearrange the above equation to solve for Δt:

Δt ≥ h/4πΔE

Substituting the given values, we have:

Δt ≥ (6.626 x 10^-34 J s)/(4π x 1.1 x 10^6 eV)

Converting electronvolts (eV) to joules (J) and simplifying, we get:

Δt ≥ 4.8 x 10^-23 s

Therefore, the smallest lifetime that the particle can have is approximately 4.8 x 10^-23 seconds.

Learn more about energy-time uncertainty principle here : brainly.com/question/29969182

#SPJ11

Electron beams are commonly used in scientific instruments. One method of producing a beam of electrons is to accelerate them across a potential difference in a capacitor style apparatus (these are used to generate an electric field). Imagine an electron released form rest in a uniform electric field between 2 oppositely charged plates (this is a capacitor...) if the field has a magnitude of 1 x 103, what is the acceleration of the electron? Which plate does it accelerate towards? The positive plate or the negative plate? The mass of an electron is 9.1 x 10-31 kg *start by calculating the force on the electron and then use newtons second law to determine the acceleration.

Answers



The acceleration of the electron in the given electric field can be calculated using the formula a = F/m, where a is the acceleration, F is the force acting on the electron, and m is the mass of the electron.


To find the force acting on the electron, we need to use the formula F = qE, where F is the force, q is the charge of the electron, and E is the magnitude of the electric field.

Since the electron has a negative charge of -1.6 x 10^-19 C, and the electric field has a magnitude of 1 x 10^3 N/C, the force acting on the electron can be calculated as:

F = (-1.6 x 10^-19 C) x (1 x 10^3 N/C) = -1.6 x 10^-16 N

The negative sign indicates that the force is acting in the opposite direction to the electric field, which means that the electron is accelerating towards the positive plate.

Now, we can use Newton's second law, F = ma, to find the acceleration of the electron:

a = F/m = (-1.6 x 10^-16 N) / (9.1 x 10^-31 kg) = -1.76 x 10^14 m/s^2

The negative sign in the acceleration indicates that the electron is accelerating towards the positive plate, which confirms our earlier observation. Therefore, the electron is accelerating towards the positive plate with an acceleration of 1.76 x 10^14 m/s^2.

learn more about electric field

https://brainly.com/question/19878202

#SPJ11

you have a string and produce waves on it with 60.00 hz. the wavelength you measure is 2.00 cm. what is the speed of the wave on this string?

Answers

The speed of the wave on the string can be calculated by multiplying the frequency (60.00 Hz) with the wavelength (2.00 cm), which gives us a result of 120 cm/s.

To further explain, the speed of a wave is defined as the distance traveled by a wave per unit time. In this case, we have a frequency of 60.00 Hz, which means that the wave produces 60 cycles per second. The wavelength, on the other hand, is the distance between two consecutive points of the wave that are in phase with each other. So, with a wavelength of 2.00 cm, we know that the distance between two consecutive points that are in phase is 2.00 cm.

By multiplying these two values, we get the speed of the wave on the string, which is 120 cm/s. This means that the wave travels at a speed of 120 cm per second along the length of the string.

To know more about the frequency, click here;

https://brainly.com/question/25867078

#SPJ11

Two stars have the same luminosity, but one appears 100 times fainter in the night sky. How much farther away is the fainter star?A. 1000 times farther B.100 times farther C.10 times farther D.4 times farther E. 2 times farther

Answers

The fainter star is 10 times farther away than the brighter star. The correct answer is C. 10 times farther.

The fainter star appears 100 times fainter, which means it is farther away from us. To determine how much farther away it is, we can use the inverse square law for luminosity:

Luminosity ∝ 1 / distance²

If L1 = L2 (since the stars have the same luminosity) and F1 = 100 × F2 (since one star appears 100 times fainter), we can write:

1 / d1² = 1 / d2² × 100

Rearranging this equation, we get:

d2 = 10 × d1

So the fainter star is 10 times farther away than the brighter star. The correct answer is C. 10 times farther.

To learn more about luminosity   visit: https://brainly.com/question/30468142

#SPJ11

Argue that the output of this algorithm is an independent set. Is it a maximal independent set?

Answers

This algorithm produces an independent set. However, it may not always yield a maximal independent set.

The given algorithm generates an independent set, as no two vertices in the output share an edge, ensuring independence.

However, it doesn't guarantee a maximal independent set.

A maximal independent set is an independent set that cannot be extended by adding any adjacent vertex without violating independence.

The algorithm might not explore all possible vertex combinations or terminate before reaching a maximal independent set.

To prove if it's maximal, additional analysis or a modified algorithm that exhaustively searches for the largest possible independent set is needed.

For more such questions on algorithm, click on:

https://brainly.com/question/13902805

#SPJ11

This algorithm produces an independent set. However, it may not always yield a maximal independent set.

The given algorithm generates an independent set, as no two vertices in the output share an edge, ensuring independence.

However, it doesn't guarantee a maximal independent set.

A maximal independent set is an independent set that cannot be extended by adding any adjacent vertex without violating independence.

The algorithm might not explore all possible vertex combinations or terminate before reaching a maximal independent  set.

To prove if it's maximal, additional analysis or a modified algorithm that exhaustively searches for the largest possible independent set is needed.

Visit to know more about Algorithm:-

brainly.com/question/13902805

#SPJ11

describe the error that results from accidentally using your right rather than your left hand when determining the direction of magnetic force on a straight current carrying conductor

Answers

The error that results from accidentally using your right rather than your left hand when determining the direction of magnetic force on a straight current carrying conductor is that the direction of the magnetic force will be reversed.

The direction of the magnetic force on a straight current carrying conductor can be determined using the right-hand rule. If you accidentally use your right hand instead of your left hand, the direction of the magnetic force will be reversed. This is because the right-hand rule applies a cross product between the direction of the current and the direction of the magnetic field, resulting in a perpendicular force. Using the wrong hand will flip the direction of this force. It is important to use the correct hand to ensure accurate results in experiments and calculations involving magnetic fields.

Learn more about determining here:

https://brainly.com/question/31755910

#SPJ11

What is the minimum downward force the nails must exert on the plank to hold it in place?

Answers

The minimum downward force the nails must exert on the plank to hold it in place is 196.2 N.

To determine the minimum downward force the nails must exert on the plank to hold it in place, we need to consider the forces acting on the plank.

Assuming the plank is at rest, the forces acting on it are:

- The weight of the plank acting downward (Wp)

- The normal force exerted by the ground on the plank acting upward (N)

- The force exerted by the nails on the plank acting downward (Fn)

Since the plank is at rest, the net force acting on it is zero.

This means:

Fn - Wp - N = 0

Solving for Fn, we get:

Fn = Wp + N

The weight of the plank (Wp) can be calculated using the formula:

Wp = mg

where

m is the mass of the plank and

g is the acceleration due to gravity (9.81 m/s²).

We are not given the mass of the plank, so let's assume it has a mass of 10 kg. Then:

Wp = 10 kg × 9.81 m/s²

     = 98.1 N

The normal force (N) is equal in magnitude and opposite in direction to the weight of the plank, so:

N = Wp

  = 98.1 N

To calculate the minimum downward force the nails must exert on the plank (Fn), we substitute the values we have calculated:

Fn = Wp + N

     = 98.1 N + 98.1 N

    = 196.2 N

Therefore, the minimum downward force the nails must exert on the plank to hold it in place is 196.2 N.

To know more about downward force refer here

brainly.com/question/17347519#

#SPJ11

opacity of the lens of the eye that impairs vision and can cause blindness is called

Answers

The opacity of the lens of the eye that impairs vision and can cause blindness is called cataract. Cataract refers to the clouding or opacification of the natural lens of the eye, which leads to a progressive decline in vision.

Cataracts commonly develop as a result of aging, but they can also be caused by factors such as trauma, certain medications, systemic diseases (e.g., diabetes), or genetic predisposition. Cataract surgery, which involves the removal of the cloudy lens and replacement with an artificial intraocular lens, is an effective treatment for cataracts, restoring clear vision for many individuals. It occurs when proteins in the lens clump together, causing the lens to become less transparent. This clouding obstructs the passage of light, resulting in blurred or distorted vision. If left untreated, cataracts can eventually lead to severe vision loss and even blindness.

Learn more about Cataract here:

https://brainly.com/question/15601309

#SPJ11

It takes 15.2 J of energy to move a 13.0-mC charge from one plate of a 17.0- μf capacitor to the other. How much charge is on each plate? Assume constant voltage

Answers

The energy required to move a charge q across a capacitor with capacitance C and constant voltage V is given by:

E = (1/2)CV^2

Rearranging this formula, we get:

V = sqrt(2E/C)

In this case, the energy required to move a 13.0-mC charge across a 17.0-μF capacitor is 15.2 J. So, we can use this value of energy and the given capacitance to find the voltage across the capacitor:

V = sqrt(2E/C) = sqrt(2 x 15.2 J / 17.0 x 10^-6 F) = 217.3 V

Now that we know the voltage across the capacitor, we can use the formula for capacitance to find the charge on each plate:

C = q/V

Rearranging this formula, we get:

q = CV

Substituting the values of C and V that we found earlier, we get:

q = (17.0 x 10^-6 F) x (217.3 V) = 3.69 x 10^-3 C

Therefore, the charge on each plate of the capacitor is approximately 3.69 milliCoulombs (mC).

To know more about capacitor refer here

https://brainly.com/question/29301875#

#SPJ11

to what temperature (in kelvins) must a balloon, initially at 25°c and 2.00 l, be heated in order to have a volume of 6.00 l? only report the numerical answer (no units)

Answers

894.45 K temperature (in kelvins) must a balloon, initially at 25°c and 2.00 l, be heated in order to have a volume of 6.00 l.

To solve this problem, we can use the combined gas law formula: P₁V₁/T₁ = P₂V₂/T₂. We know the initial temperature is 25°C, which is equivalent to 298.15 K (adding 273.15 to convert from Celsius to Kelvin). We also know the initial volume is 2.00 L, and the final volume is 6.00 L. Plugging these values into the formula, we get:
P₁V₁/T₁ = P₂V₂/T₂
(1 atm)(2.00 L)/(298.15 K) = (1 atm)(6.00 L)/(T₂)
T₂ = (1 atm)(6.00 L)/(1 atm)(2.00 L)/(298.15 K)
T₂ = 894.45 K
Therefore, the temperature the balloon must be heated to in kelvins to have a volume of 6.00 L is approximately 894.45 K.

To know more about temperature visit:

brainly.com/question/20846849

#SPJ11

the table lists the heights and weights of six wide receivers who played for the atlanta falcons during the 2010 football season. a. make a scatter plot for the data. be sure to label your axes.

Answers

Unfortunately, as an AI text-based model, I am unable to directly create visual content like scatter plots. However, I can guide you on how to create a scatter plot based on the given data.

To make a scatter plot for the heights and weights of the wide receivers, follow these steps:

1. Prepare your data: Organize the heights and weights of the six wide receivers in a table, with one column for heights and another for weights.

2. Choose a scale: Determine the appropriate scale for each axis based on the range of values in the data. Ensure that the plot will adequately represent the variations in both height and weight.

3. Assign axes: Label the vertical axis (y-axis) for the heights and the horizontal axis (x-axis) for the weights. Include the units of measurement (e.g., inches for height and pounds for weight).

4. Plot the data points: For each wide receiver, locate the corresponding height and weight values on the axes and mark a point. Repeat this for all six wide receivers.

5. Add labels and title: Label each data point with the respective player's identifier (name, jersey number, or any other identifier you prefer). Additionally, provide a title for the scatter plot, such as "Height and Weight of Atlanta Falcons Wide Receivers (2010 Season)."

Remember to maintain clear and readable labels, and use appropriate symbols or markers for the data points.

By following these steps, you can create a scatter plot representing the heights and weights of the Atlanta Falcons wide receivers during the 2010 football season.

Learn more about creating scatter plots and data visualization techniques using graphing software or tools available online for your specific needs.

https://brainly.com/question/14288372?referrer=searchResults

#SPJ11

the distance a spring is compressed is decreased by a third. by what factor does the spring force () and elastic potential energy of the spring () change?

Answers

Spring force decreases by a factor of 3/2, and elastic potential energy decreases by a factor of 9/4.

The force exerted by a spring is given by Hooke's Law, F = -kx, where F is the force, x is the distance the spring is compressed or stretched, and k is the spring constant. If x is decreased by a third, then the force decreases proportionally by a factor of 3/2. So the spring force decreases by a factor of 3/2.

The elastic potential energy stored in a spring is given by the formula U = (1/2)kx^2. If x is decreased by a third, then the potential energy stored in the spring decreases by a factor of (1/2)k(1/3x)^2 = (1/18)kx^2. So the elastic potential energy decreases by a factor of 9/4.

Learn more about Spring force here:

https://brainly.com/question/14655680

#SPJ11

A grating with 8000 slits space over 2.54 cm is illuminated by light of a wavelength of 546 nm. What is the angle for the third order maximum? 31.1 degree 15.1 degree 26.3 degree 10.5 degree

Answers

The angle for the third order maximum is 31.1 degrees.

The formula for calculating the angle for the nth order maximum is given by: sinθ = nλ/d, where θ is the angle, λ is the wavelength of light, d is the distance between the slits (also known as the grating spacing), and n is the order of the maximum.
In this case, the grating has 8000 slits spaced over 2.54 cm, which means the grating spacing d = 2.54 cm / 8000 = 3.175 x 10^-4 cm. The wavelength of light is given as 546 nm, which is 5.46 x 10^-5 cm.
To find the angle for the third order maximum, we can plug in these values into the formula: sinθ = 3 x 5.46 x 10^-5 cm / 3.175 x 10^-4 cm. Solving for θ gives us sinθ = 0.524, or θ = 31.1 degrees (rounded to the nearest tenth of a degree). Therefore, the correct answer is 31.1 degrees.
This calculation involves the use of the formula that relates the angle, wavelength, and grating spacing, which allows us to determine the maximum angles at which constructive interference occurs.

To know more about angle visit:

https://brainly.com/question/31814721

#SPJ11

Define the following characteristics of signals: (a) frequency content, (b) amplitude, (c) magnitude, and (d) period.

Answers

Here's a brief explanation of each of these signal characteristics:

(a) Frequency content refers to the range of frequencies present in a signal. It is often represented using a frequency spectrum, which shows the amplitudes of each frequency component in the signal.

(b) Amplitude refers to the strength or intensity of a signal, usually measured as the maximum displacement of the signal from its average value. It can be thought of as the "height" of a signal's waveform.

(c) Magnitude is a general term that can refer to the overall size or strength of a signal, or to the specific amplitude of a particular frequency component. In some contexts, magnitude may also refer to the absolute value of a complex number.

(d) Period refers to the time it takes for a signal to complete one full cycle. For example, if a signal repeats the same pattern every 1 second, it has a period of 1 second. The inverse of the period is frequency, which is measured in Hertz (Hz) and represents the number of cycles per second.

To know more about the amplitude, click here;

https://brainly.com/question/8662436

#SPJ11

Problem 2.43 Solve the time-independent Schrödinger equation for a centered infinite square well with a delta-function barrier in the middle: V(x0 = { αδ(x) , -a < x < +a, [infinity], |x| > a Treat the even and odd wave functions separately. Don't bother to normalize them. Find the allowed energies (graphically, if necessary). How do they compare with the corresponding energies in the absence of the delta function? Explain why the odd solutions are not affected by the delta function. Comment on the limiting cases α -> 0 and α -> [infinity].

Answers

To solve the time-independent Schrödinger equation for a centered infinite square well with a delta-function barrier in the middle, we need to consider the even and odd wave functions separately. The potential function is given as V(x0 = { αδ(x) , -a < x < +a, [infinity], |x| > a. We can use the boundary conditions to determine the form of the wave function in each region. For -a < x < -α and α < x < a, the wave function takes the form of a plane wave. For -α < x < α, the wave function takes the form of a combination of exponential functions.

Next, we can find the allowed energies by solving the Schrödinger equation in each region and matching the wave functions and their derivatives at the boundaries. We can also use a graphical approach to find the energies. The presence of the delta function barrier affects the even solutions, causing a shift in energy levels compared to the absence of the delta function. However, the odd solutions are not affected by the delta function because the wave function is zero at the position of the delta function.

The limiting cases of α -> 0 and α -> [infinity] can be understood as follows. In the limit of α -> 0, the delta function barrier becomes infinitely narrow, and the potential approaches zero. Therefore, the energy levels approach those of the infinite square well without the barrier. In the limit of α -> [infinity], the delta function barrier becomes infinitely wide and high, and the wave function becomes zero at the position of the barrier. Therefore, the energy levels approach those of a single particle in a finite potential well with infinitely high walls.

To know more about Schrödinger equation, click here;

https://brainly.com/question/31390478

#SPJ11

A nuclear power plant draws 3.1×106 L/min of cooling water from the ocean.
If the water is drawn in through two parallel, 3.4-m-diameter pipes, what is the water speed in each pipe?

Answers

The water speed in each pipe is approximately 2.85 m/s.

We know, flow rate of any liquid can be calculated as

Q = Av

where A = cross-sectional area of one pipe, and

           v = water speed in each pipe.

The flow rate 'Q' of water through two parallel pipes can be found by adding the flow rates through each pipe.

i.e., Q = 2Av

We know, the cross-sectional area 'A' of a pipe with diameter 'd' is given by:

A = π(d/2)² = π/4 × d²

Substituting d = 3.4 m, we get:

A = π/4 × (3.4 m)²

  = 9.07 m²

The volume flow rate of water is Q = 3.1 × 10⁶ L/min,

converting it to SI units, we get;

Q = 3.1 × 10⁶ L/min × (1 m³ / 1000 L) × (1 min / 60 s)

   = 51.7 m³/s

Now we can solve for the water speed v, as

v = Q / (2A)

 = 51.7 m³/s / (2 × 9.07 m²)

 ≈ 2.85 m/s

Therefore, the water speed in each pipe is approximately 2.85 m/s.

Learn more about water flow here

brainly.com/question/15851784

#SPJ4

a system absorbs 12 jj of heat from the surroundings; meanwhile, 28 jj of work is done on the system. what is the change of the internal energy δethδethdeltae_th of the system?

Answers

The change in internal energy (ΔE_th) of the system is 40 J.

To determine the change in internal energy (ΔE_th) of the system when it absorbs 12 J of heat from the surroundings and 28 J of work is done on the system, we can use the first law of thermodynamics equation:

ΔE_th = Q + W

where ΔE_th is the change in internal energy, Q is the heat absorbed by the system, and W is the work done on the system.

Given, Q = 12 J (heat absorbed) and W = 28 J (work done on the system).

Now, substitute the given values into the equation:

ΔE_th = 12 J + 28 J

ΔE_th = 40 J

To know more about heat of system refer https://brainly.com/question/28199463

#SPJ11

Work done on a point mass A point mass m = 7 kg is moving in 2D under the influence of a constant force F = 2i-8j N. At time t = 0 s the mass has position vector ro = 7i - 8j m, while by time t =6 s it has moved to rf = 4i+3j m. How much work W does the force F do on the point mass between these two times? W = _____ J

Answers

-94 J is the work done (W) on the point mass between these two times.

To find the work done (W) on a point mass (m = 7 kg) between two times (t = 0 s and t = 6 s) under the influence of a constant force F = 2i - 8j N, we can use the formula:

W = F • Δr

where W is the work done, F is the force, and Δr is the change in position vector.

First, we need to find the change in position vector:

Δr = rf - ro = (4i + 3j) - (7i - 8j) = -3i + 11j

Now, we can find the dot product of F and Δr:

F • Δr = (2i - 8j) • (-3i + 11j) = 2(-3) + (-8)(11) = -6 - 88 = -94

Therefore, the work done (W) on the point mass between these two times is:

W = -94 J

More on work: https://brainly.com/question/12157281

#SPJ11

2. A hydraulic press has an input piston radius of 0,5 mm. It is linked to an output piston that is three times that size. What mechanical advantage does this press have? ​

Answers

Answer:A hydraulic press with a 0.5 mm input piston radius and a three times larger output piston has a mechanical advantage of 16, or 1:16.

Explanation: The mechanical advantage can be calculated using the following formula: mechanical advantage = output force / input force = output piston area / input piston area. The area of the output piston is nine times greater since it is three times the size of the input piston. The mechanical advantage is thus 9 / 0.56 = 16 or 1:16. This means that the hydraulic press has the capability of multiplying the input force by a factor of 16, making it considerably easier to lift heavy things or apply a considerable amount of power.

10.30 A vertical steel tube carries water at a pressure of 10 bars. Saturated liquid water is pumped into the D= 0.1-m-diameter tube at its bottom end (x=0) with a mean velocity of u m

=0.05 m/s. The tube is exposed to combusting pulverized coal, providing a uniform heat flux of q ′′
=100,000 W/m 2
. (a) Determine the tube wall temperature and the quality of the flowing water at x=15 m. Assume G s,f

=1. (b) Determine the tube wall temperature at a location beyond x=15 m where single-phase flow of the vapor exists at a mean temperature of T sat ​
. Assume the vapor at this location is also at a pressure of 10 bars. Change q ′′
tp 50,000 W/m²

Answers

(a) At x = 15 m, the tube wall temperature is 432.2 °C, and the quality of the flowing water is 0.23. The heat transfer rate per unit length of the tube is 549.5 W/m.

(b) At a location where single-phase flow of the vapor exists at a mean temperature of 10 bars, the tube wall temperature is 1395.6 °C.

(a) To determine the tube wall temperature and the quality of the flowing water at x=15 m, we need to first calculate the heat transfer rate per unit length of the tube using the given heat flux and tube diameter:

q'' = 7.0 x 10⁴ W/m²

d = 0.1 m

A = pi × [tex]d^{2/4}[/tex] = 7.85 x 10⁻³ m²

q = q'' × A = 549.5 W/m

Calculate the Reynolds number and the friction factor using the mean velocity and the tube diameter:

[tex]u_m[/tex] = 0.05 m/s

Re = [tex]u_m[/tex] × d ÷ nu, where nu is the kinematic viscosity of water at 10 bars.

From the tables, we find nu = 3.3 x 10⁻⁶ m²/s at this pressure.

Re = 1515

Using the Moody chart, we find the friction factor to be f = 0.027.

Now, we can use the energy balance equation to determine the tube wall temperature at x=15 m:

q = m₁ × [tex]h_{fg[/tex] + m₁ × [tex]C_{pl[/tex] × ([tex]T_w-T_4[/tex]) + q'' pid

m₁ = [tex]rho_l[/tex] × [tex]Au_m[/tex]

[tex]rho_l[/tex] = rho₄ = 646.83 kg/m³, the density of saturated liquid water at 10 bars.

[tex]h_{fg[/tex] = 2230.5 kJ/kg, the enthalpy of vaporization at 10 bars.

[tex]C_{pl[/tex] = 4.18 kJ/kg.K, the specific heat capacity of liquid water.

T₄ = 179.86 °C, the saturation temperature at 10 bars.

[tex]T_w[/tex] = 432.2 °C

x = 15.15 m

(b) To determine the tube wall temperature at a location where single phase flow of the vapor exists at a mean temperature at 10 bar, we need to use the energy balance equation again, but this time assuming that the flow is entirely vapor:

q = m₁ × [tex]C_{pv[/tex]([tex]T_w - T_1[/tex])

[tex]T_w[/tex] = q ÷ (m₁ × [tex]C_{pv[/tex])

m₁ = [tex]rho_v[/tex] × [tex]Au_m[/tex]

[tex]rho_v[/tex] = 6.09 kg/m³, the density of water vapor at 10 bars and 432.2 °C.

[tex]C_{pv[/tex] = 1.86 kJ/kg.K, the specific heat capacity of water vapor at 10 bars and 432.2 °C.

[tex]T_w[/tex] = 1395.6 °C

To learn more about temperature follow the link:

https://brainly.com/question/2094845

#SPJ4

The complete question is:

A vertical steel tube carries water at a pressure of 10 bars. Saturated liquid water is pumped into the D = 0.1 m diameter tube at its bottom end (x=0) with a mean velocity of u_m =0.05 m/s. The tube is exposed to combusting pulverized coal, providing a uniform heat flux of q′′ = 7.0 x 10⁴ W/m².

(a) Determine the tube wall temperature and the quality of the flowing water at x=15 m. Assume [tex]G_{(sf)[/tex] =1.

(b) Determine the tube wall temperature at a location where single-phase flow of the vapor exists at a mean temperature​ of 10 bar.

A wildlife keeper chases a rabbit that is trying to escape. In which situation would you be able to identify the object with the greater kinetic energy

Answers

The situation in which the object with greater kinetic energy can be identified is when the wildlife keeper and the rabbit are both in motion, and their velocities and masses are known. The object with greater kinetic energy would be the one with a higher mass and/or a higher velocity.

Kinetic energy is given by the equation KE = (1/2)mv^2, where m is the mass and v is the velocity of an object. In this scenario, if both the wildlife keeper and the rabbit are in motion, and their masses and velocities are known, we can calculate their respective kinetic energies using the equation. The object with the greater kinetic energy will have a larger product of mass and velocity, indicating higher energy of motion. Therefore, by comparing the calculated values, we can identify the object with greater kinetic energy.

learn more about energy here:

https://brainly.com/question/29153082

#SPJ11

Arod of length 12 meters and charge 8 uc lies along the x-axis from (-6.) to (6,0) meters. The linear charge density of the rod is given by 1 = kx There is also a charge of 6C at (0,4) meters. What is the potential energy of this charge configuration? a. 588 m b.724 m c.679 m d. 533 m) e. 646.md

Answers

The potential energy of this charge is d. 533 mj.

To calculate the potential energy of the charge configuration, we need to first find the electric potential due to the rod and the point charge at the location of the point charge, and then use the formula for potential energy:

U = q1q2 / 4piepsilon0r

where q1 and q2 are the charges, r is the distance between them, and epsilon0 is the electric constant.

The electric potential due to the rod at the location of the point charge is given by:

V_rod = k * integral[(x-x0)/[tex]r^{3}[/tex] dx] from -6 to 6

where x0 is the x-coordinate of the point charge, r is the distance between the point charge and the point on the rod being considered, and k is the Coulomb constant.

Substituting the values given in the problem, we have:

x0 = 0

k = [tex]910^{9}[/tex] [tex]Nm^{2}[/tex]/[tex]C^{2}[/tex]

r = sqrt([tex]6^{2}[/tex] + [tex]4^{2}[/tex]) = 2*sqrt(10) meters

The integral can be evaluated as follows:

V_rod = k * (1/[tex]r^{3}[/tex]) * integral[(x-x0) dx] from -6 to 6

= k * (1/[tex]r^{3}[/tex]) * [ (1/2)*[tex](x-x0)^{2}[/tex]] from -6 to 6

= k * (1/[tex]r^{3}[/tex]) * [ (1/2)[tex]6^{2}[/tex] - (1/2)-[tex]6^{2}[/tex] ]

= k * (1/[tex]r^{3}[/tex]) * 36

= 2.88 * [tex]10^{9}[/tex] V

The electric potential due to the point charge at its own location is infinite, but at a point on the x-axis, it can be calculated as:

V_point = k*q / r

Substituting the values given in the problem, we have:

q = 6 C

r = 4 meters

V_point = k*q / r

= 1.35 * [tex]10^{9}[/tex] V

The total electric potential at the location of the point charge is the sum of the potentials due to the rod and the point charge:

V_total = V_rod + V_point

= 4.23 *[tex]10^{9}[/tex]  V

Finally, we can use the formula for potential energy to calculate the potential energy of the charge configuration:

U = q1q2 / 4piepsilon0r

= ([tex]810^{-6}[/tex] C) * (6 C) / (4pi8.[tex]8510^{-12}[/tex] N*[tex]m^{2}[/tex]/[tex]C^{2}[/tex]) * 4 meters

= 5.33 * [tex]10^{-6}[/tex] J

= 533 mJ

Therefore, The potential energy of this charge is 533 mj. Therefore, the correct answer is option d.

know more about potential energy here:

https://brainly.com/question/21175118

#SPJ11

A small rocket burns 0.0500 kg of fuel per second, ejecting it as agas with velocity relative to the rocket of magnitude 1600 m/s. a)What is the thrust of the rocket? b) Would the rocket operate inouter space where there is no atmosphere? If so, how would yousteer it? Could you brake it?Solutions:
a) 80.0N
b) yes

Answers

The thrust of the rocket is 80.0 N. Therefore correct option is a.

The thrust of the rocket can be found using the formula:

Thrust = mass flow rate of fuel x velocity of exhaust gas relative to the rocket

Substituting the given values, we get:

Thrust = 0.0500 kg/s x 1600 m/s = 80.0 N

Therefore, the thrust of the rocket is 80.0 N.

The rocket would operate in outer space where there is no atmosphere, as the thrust generated is due to the ejection of exhaust gas and not by relying on air resistance. Steering the rocket into outer space would be done by using thrusters that can change the direction of the exhaust gas relative to the rocket. Braking the rocket would also be possible by firing the thrusters in the opposite direction of motion to slow down the rocket.

To learn more about  velocity  visit: https://brainly.com/question/80295

#SPJ11

what kind of image is created between the center of curvature and the focal point by a concave mirror?

Answers

Between the centre of curvature and the focus point, a concave mirror produces a virtual, upright, and magnified image. A virtual image is the term used to describe this kind of image.

The centre of curvature in a concave mirror is situated on the same side as the object. The image created is virtual, which means it cannot be projected onto a screen when the object is positioned between the centre of curvature and the focus point. The picture is bigger than the mirror and appears to be behind it.

The position of the item in relation to the focus point and centre of curvature determines the precise features of the image, including its size and distance from the mirror.

To know more about centre of curvature, here

brainly.com/question/30242206

#SPJ4

a student holds a laser that emits light of wavelength 638.5 nm. the laser beam passes though a pair of slits separated by 0.500 mm, in a glass plate attached to the front of the laser. the beam then falls perpendicularly on a screen, creating an interference pattern on it. the student begins to walk directly toward the screen at 3.00 m/s. the central maximum on the screen is stationary. find the speed of the 50th-order maxima on the screen.

Answers

The position and speed of the 50th-order maximum is 4.77 x [tex]10^{-4[/tex] mm from the left edge of the screen.  

First, we need to calculate the wavelength of the light emitted by the laser. Since the wavelength is given as 638.5 nm, we can use the formula:

λ = c/f

We are given that the laser emits light of frequency f. Since the wavelength is λ and the speed of light is c, we can solve for f:

f = c/λ

Substituting the given value for λ (638.5 nm), we get:

f = 3 x [tex]10^{-4[/tex]  m/s / 638.5 x [tex]10^{-4[/tex]  m

f = 4.77 x [tex]10^{-4[/tex]  Hz

Therefore, the frequency of the light emitted by the laser is 4.77 x 10^14 Hz.

Next, we need to calculate the distance between the slits and the screen. We are given that the distance between the slits is 0.500 mm. To find the distance from the slits to the screen, we can use the formula:

d = h * sin(θ)

Since the light is incident on the screen perpendicular to the slits, the angle between the incident ray and the normal to the slit is 90°. Therefore, we can use the value of θ as 90°.

The height of the slits is given as 0.500 mm. Therefore, we can substitute these values into the formula to find the distance from the slits to the screen:

d = 0.500 mm * sin(90°)

d = 0.500 mm * 1

d = 0.500 mm

Therefore, the distance from the slits to the screen is 0.500 mm.

Finally, we can use the equation for the central maximum in an interference pattern to find the position of the 50th-order maximum. The equation for the central maximum is:

M = m * L / (N + L)

Since the light is incident on the screen perpendicular to the slits, the distance between the central maximum and the screen is equal to the distance between the screen and the center of the central maximum. Therefore, we can substitute this value into the equation for the central maximum:

M = m * L / (N + L)

M = 0.500 mm / (0.250 mm + 0.500 mm)

M = 2.00

Therefore, the position of the central maximum is 2.00 mm from the left edge of the screen.

To find the position of the 50th-order maximum, we can use the equation for the position of a maximum in a sinusoidal wave:

x = (2n + 1)πm / λ

x = (2n + 1)π(2.00) / (638.5 x [tex]10^{-4[/tex] )

x = (2n + 1)π2.00 / (638.5 x [tex]10^{-4[/tex] )

x = 4.77 x[tex]10^{-4[/tex]

Therefore, The position of the 50th-order maximum is 4.77 x [tex]10^{-4[/tex]  mm from the left edge of the screen.  

Learn more about speed Visit: brainly.com/question/13943409

#SPJ4

Find the equation of the ellipse with the following properties Express the answer in standard form. Centered at (1,3), the major axis of length 16 oriented vertically, the minor axis of length 2.

Answers

To find the equation of the ellipse with the given properties, we can start by using the standard form of the equation for an ellipse:

(x - h)^2/a^2 + (y - k)^2/b^2 = 1

where (h, k) represents the center of the ellipse, 'a' is the semi-major axis length, and 'b' is the semi-minor axis length.

Given:

Center: (1, 3)

Major axis length: 16 (oriented vertically)

Minor axis length: 2

1. Center: (h, k) = (1, 3)

Therefore, the equation becomes:

(x - 1)^2/a^2 + (y - 3)^2/b^2 = 1

2. Major axis length: 16 (oriented vertically)

The major axis is vertical, which means it is parallel to the y-axis. The length of the major axis is twice the length of the semi-major axis, so a = 16/2 = 8. The equation becomes:

(x - 1)^2/8^2 + (y - 3)^2/b^2 = 1

3. Minor axis length: 2

The minor axis is horizontal, which means it is parallel to the x-axis. The length of the minor axis is twice the length of the semi-minor axis, so b = 2/2 = 1. The equation becomes:

(x - 1)^2/8^2 + (y - 3)^2/1^2 = 1

Simplifying further, we have:

(x - 1)^2/64 + (y - 3)^2 = 1

Therefore, the equation of the ellipse in standard form is:

(x - 1)^2/64 + (y - 3)^2 = 1

To know more about ellipse refer here

https://brainly.com/question/20393030#

#SPJ11

Other Questions
In a traffic circle/roundabout, yield the right of way to ____. In ____________ , a double-stranded RNA molecule separates into single strands. One of the strands prevents a complementary mRNA from being translated. The monetary policy tool whereby the Federal Reserve buys and sells government bonds is called: the discount rate. open-market operations. reserve requirements. moral suasion. Indicate where in the lymph nodes the listed cell types are found by dragging labels to the appropriate boxes. Some labels are used more than once. True or false? Initially when using shaping, reinforcement is provided for a response that is similar to the target response.A. TrueB. False A word or phrase to help identify a file when you do not know the file name during the file expiration search A 40.0 kg beam is attached to a wall with a hi.nge and its far end is supported by a cable. The angle between the beam and the cable is 90. If the beam is inclined at an angle of = 31.0 with respect to horizontal.The horizontal component of the force exerted by the hi.nge on the beam = 8.662101 NWhat is the magnitude of the force that the beam exerts on the hi.nge? slope:y-intercept:HELP PLS20 points In geometry, Heron's formula (sometimes called Hero's formula), named after Hero of Alexandria, gives the area of a triangle by requiring no arbitrary choice of side as base or vertex as origin, contrary to other formulas for the area of a triangle, such as half the base times the height. Use Heron's formula to find the area, in square meters, of ABC.a=7m, b=5m, c=6m Solve the equation. 1. for parentheses: distribute 4-2(x+7) = 3(x+5) 2. if necessary: combine terms 3. apply properties: add subtract multiply divide 4. to start over: reset the how do you solve (a-28)(a-5) Is this figure a polygon? Explain. WILL MAKE BRAINLIEST!! What type of angle is angle A? Which type of sales promotion tactic is the distribution of free food products to customers at costco? Glucose solution is administered to a patient in a hospital. The density of the solution is 1.308 kg/l. If the blood pressure in the vein is 35.7 mmHg, then what is the minimum necessary height of the IV bag above the position of the needle? According to the Arrhenius definitions of acids and bases, choose the bases from the list of acids and bases. Check all that apply. Maximizing local profit or minimizing cost in a supply chain is best described as? Technetium -99 (half-life = 6.01) is used in the medical imaging. How many half-lives would go by in 44.0h? Which responses by the student indicate an understanding of erythromycin administration? Ms Gates has recently become dually eligible for medicare and medicaid, she is very concerned about