Light passes from a crown glass container into water. a) Will the angle of refraction be greater than, equal to, or less than the angle of incidence? Please explain. b) IF the angle of refraction is 20 degrees, what is the angle of incidence?

Answers

Answer 1

The angle of incidence is approximately 51.1 degrees.

a) The angle of refraction will be less than the angle of incidence.

This is because when light passes from a medium with a higher refractive index (crown glass) to a medium with a lower refractive index (water), it bends away from the normal (a line perpendicular to the surface of the interface between the two media).

The angle of incidence is the angle between the incident ray and the normal, and the angle of refraction is the angle between the refracted ray and the normal.

Snell's law describes the relationship between the angles of incidence and refraction:

n1 * sin(theta1) = n2 * sin(theta2)

where n1 and n2 are the refractive indices of the two media, and theta1 and theta2 are the angles of incidence and refraction, respectively.

b) Using Snell's law and the values given, we can solve for the angle of incidence:

n1 * sin(theta1) = n2 * sin(theta2)

sin(theta1) = (n2/n1) * sin(theta2)

sin(theta1) = (1.33/1.52) * sin(20)

sin(theta1) = 0.792

theta1 = sin^-1(0.792)

theta1 = 51.1 degrees

To know more about refraction refer here

https://brainly.com/question/14760207#

#SPJ11


Related Questions

You are raising up a big bucket of water from a 22.5 m deep well. The combined mass of the water and the bucket is 11.3 kg. The bucket is attached to a heavy duty steel chain. The mass of the chain is 17.9 kg. How much work do you perform during the lifting process? Tries 0/12 If it takes 1.75 minutes for you to raise the bucket of water out of the well, then what was your average power?

Answers

The amount of work done during the lifting process is 4465.125 J and our average power will be 42.525 W.

Given:

Depth of the well, h = 22.5m

Mass of heavy-duty steel chain, M = 17.9 kg

The combined mass of the water and bucket, m = 11.3 kg

time taken to raise the bucket out of the water, T = 1.75 min = 105 s

Calculation:

Consider that the center of mass of the steel chain is at the midpoint of the depth of the well.

Now, the work done during the lifting process can be calculated as:

W.D = (Work done in lifting bucket filled with water) + (work done to lift    

                                                                                              the steel chain)

W.D = mgh + Mg (h/2)      -( 1 )

where g is the acceleration due to gravity

Applying values in the above equation we get:

W.D = mgh + Mg (h/2)

       = (11.3 kg)(9.8 m/s²)(22.5 m) + (17.9 kg)(9.8 m/s²)(22.5 m / 2)

       = 2491.65 + 1973.475

       = 4465.125 J

We know that the average power is given as:

P_avg = W.D / T     - ( 2 )

where W.D is the work done during the lifting process

            T is the time taken to raise the bucket out of the well

Applying values in the above equation, we get:

P_avg = W.D / T

           = (4465.125 J)/(105 s)

           = 42.525 W

Therefore, the amount of work done during the lifting process is 4465.125 J and our average power will be 42.525 W.  

Learn more about work and energy here:

https://brainly.com/question/17290830

#SPJ4  

Complete the following nuclear reaction:

Answer choice
a) γ

b) α

c) β–

d) p

Answers

The particle that was given off in the reaction beta rays is β–. Option C

What is a nuclear reaction?

A nuclear reaction will involve the change in the nucleus of an atom. It often leads to the production of new nucleus. As we can see the equation, there was a transformation from nitrogen nucleus to oxygen atom.

Thus, the particle that was given off in the reaction beta rays is β–. The fact that the mass number remained the same but the atomic number increased by one unit from left to right implies that a beta decay has occurred.

Learn more about beta rays:https://brainly.com/question/2088794

#SPJ1

A ball of mass 4 kg is initially traveling at 2 m/s and has a 5 N force applied to it for 3 s. What is the final velocity of the ball?
A. 4 m/s
B. 12 m/s
C. 5.75 m/s
D. 3.25 m/s

Answers

Answer:

the answer to your question will be D

Explanation:

5 N* 3S =3.25

2. A ball is tossed straight upwards with a velocity of 60m/s. Using an estimate of gravity of -10m/s², about how many seconds would it take to reach the peak (top of the flight). A.) 10 seconds B.) 3 seconds C.) 6 seconds D.) 12 seconds​

Answers

Answer: A

Explanation:

Consider two copper wires. one has twice the length and twice the cross-sectional area of the other. how do the resistances of these two wires compare?

Answers

Answer:

R = ρ L / A     where R is the resistance and ρ the resistivity:

R2 / R1 = (L2 / A2) / (L1 / A1) = L2 * A1 / (L1 * A2)

R2 / R1 =  (2 L * A) / (L * 2 A) = 1

Their resistances should be the same.

A car approaches a stationary police car at 36 m/s. The frequency of the siren (as heard in the police car) is 500 Hz. What is the frequency (in Hz) heard by an observer in the moving car as he approaches the police car

Answers

The frequency heard by an observer in the moving car as he approaches the police car is 558.6 Hz.

Frequency hear by the observer

The frequency heard by the observer is calculated by applying the principle of Doppler effect.

f₀ = f'[(v/v - vs)]

where;

f₀ is the observed frequencyv is speed of sound = 343 m/svs is the speed of the source

f₀ = 500[(343 / 343 - 36)]

f₀ = 500(343/307)

f₀ = 558.6 Hz

Thus, the frequency heard by an observer in the moving car as he approaches the police car is 558.6 Hz.

Learn more about frequency here: https://brainly.com/question/10728818

#SPJ1

In the pinball game, momentum is transferred from the plunger to the ___

Answers

In the pinball game, momentum is transferred from the plunger to the ball.

What is momentum?

Momentum is the quantity of motion of a moving body, measured as a product of its mass and velocity.

The formula of the momentum is: p = m*v

Here a pinball game machine is given.

We know that,

A plunger in a pinball is a spring loaded rod used to shoot the ball out into the playing field.When the plunger tugged all the way back and released, the plunger will send the ball flying around the playfield. so here elastic potential energy is converted to kinetic energy.That is how the momentum is transferred to the pinball from the plunger.

Hence,

In the pinball game, momentum is transferred from the plunger to the ball.

Learn more about momentum here:

https://brainly.com/question/2193212

#SPJ4

Which requires more work, increasing a car's speed from 0 mph to 30 mph or from 50 mph to 60 mph?

Answers

Increasing a car's speed from 0 mph to 30 mph requires more work than that of 50 mph to 60 mph.

What is work?

Work is a measure of energy expended in moving an object. It is calculated by multiplying the force by the distance.

According to this question, work is required to move a car from one position to another.

The distance moved from 0 - 30mph is more than that moved from 50 - 60mph, therefore, increasing a car's speed from 0 mph to 30 mph requires more work than that of 50 mph to 60 mph.

Learn more about work at: https://brainly.com/question/19382352

#SPJ1

Why do we tallk about radio waves as a group and not the frequeny of radio waves

Answers

Because radio waves are important and everyone should know because without them y=my+D

Consider the function e(h) = ε h h 2 6 m where m is a bound for the third derivative of a function. Show that e(h) has a minimum at p3 3ε/m

Answers

Since , e"(h) = M >0

hence ,  At p3 3ε/M  function e(h) has a minimum of function.

In mathematics, point at which the value of a function is less than or equal to the value at any nearby point (local minimum) or at any point (absolute minimum) or the minimum value of a function is the lowest point of a vertex

e(h) = ∈ /h +( [tex]h^{2}[/tex]/6) M

e'(h) = - ∈ /[tex]h^{2}[/tex] + (2h/6) M

putting , e'(h)  = 0

- ∈ /[tex]h^{2}[/tex] + (2h/6) M  = 0

h = [tex](3 /M)^{1/3}[/tex] *  (∈^(1/3))

e"(h) = 2∈ / [tex]h^{3}[/tex] + (2M)/6                          equation 1

substituting value of h in equation 1, we get

e"(h) = 2∈M / 3∈ + M/3

e"(h) = M >0

hence ,  At p3 3ε/M  function e(h) has a minimum

To learn more about minimum of function here

https://brainly.com/question/24195665?referrer=searchResults

#SPJ4

A solenoid 6.00 cm in diameter and 10.0 cm long has 750 turns and carries a current of 15.0 A. Calculate the magnetic flux through the circular cross-sectional area of the solenoid.

Answers

The magnetic flux through the circular cross-sectional area of the solenoid is 0.00066 Weber or (Tm²).

What is a solenoid?

A wire tightly twisted in a lengthy, thin coil is a solenoid. Due to its design, the solenoid will have an electromagnet inside of it and a weak magnetic field surrounding it if we pass a current through it.

Equation of solenoid's magnetic field:

The simplest solenoid to describe is one with unlimited length. An infinite solenoid's magnetic field has a constant within and a precise zero value outside. If we can accept that the magnetic field near the ends will be different from what is calculated for just an infinite solenoid, the unlimited solenoid is frequently a rough estimate of an actual, finite-length solenoid.

By utilizing the convolution operation as well as right hand rule, the magnetic field within a large solenoid is appropriately computed, but all of that can be condensed into:

B = (µ₀ × N × I )/ L

where

B = magnetic field (Tesla)

µ₀ = [tex]\pi[/tex]× 10^-7 (Tm/A ) is the vacuum permeability,

N = number of turns on solenoid,

I = electric current (Ampere)

L = length of the solenoid (m)

According to the question;

A diameter of solenoid 6.00 cm.

A radius of solenoid is 3 cm = 0.03m

Number of turns = 750

The length of solenoid is 10cm = 0.1m

Substitute all the values in equation to fine mangetic filed.

B = ([tex]\pi[/tex]×[tex]10^{-7}[/tex] × 750× 15 )/ 0.1

B = 0.035 Tesla

The formula for magnetic flux is

Ф = B×A

   = B×([tex]\pi[/tex][tex]r^{2}[/tex])

   = 0.035×[tex]\pi[/tex]×[tex].03^{2}[/tex]

Ф = 0.000099

Ф = 99×[tex]10^{-6}[/tex] Weber

Therefore, the magnetic flux through the circular cross-sectional area of the solenoid. is 99×[tex]10^{-6}[/tex] Weber.

To know more about the solenoid, here

https://brainly.com/question/17086348

#SPJ4

An object at rest has no ________ energy, but it may have ________ energy resulting from its location or structure. An object at rest has no ________ energy, but it may have ________ energy resulting from its location or structure. chemical; potential kinetic; potential kinetic; heat potential; kinetic

Answers

Answer: An object at rest has no kinetic energy, but it may have potential energy resulting from its location or structure.

Explanation: To find the answer, we need to know more about the kinetic and potential energies.

What is kinetic energy of a body?Kinetic energy is a form of mechanical energy possessed by a body by virtue of its motion.Kinetic energy of a body of mass m moving with a velocity v is given by,

                           [tex]KE=\frac{1}{2}mv^2[/tex]

What is potential energy?Potential energy is a form of mechanical energy possessed by a body by virtue of its position in the field or configuration.PE is always associated with a conservative force.There cannot be potential energy due to frictional or viscous forces.

Thus, we can conclude that, an object at rest has no kinetic energy, but it may have potential energy resulting from its location or structure.

Learn more about the kinetic and potential energies here:

https://brainly.com/question/28044620

#SPJ4

Two large parallel conducting plates are 9.0 cm apart and carry equal but opposite charges on their facing surfaces. The magnitude of the surface charge density on either of the facing surfaces is 3.7 nC/m 2. Determine the magnitude of the electric potential difference between the plates.

Answers

The magnitude of the electric potential difference between the plates is 37.63 V.

Given:

Distance between the plates, d = 9 cm

Surface charge density, ρ = 3.7 nC/m² = 3.7 × 10⁻⁹ C/m²

Calculation:

For two parallel plate conductors, the electric field is given as:

E = ρ/ε₀

where ρ is the charge density

           ε₀ is the permeability of free space

Applying values in the above equation we get:

E = ( 3.7 × 10⁻⁹ C/m²)/(8.85 × 10⁻¹² C²/m)

  = 418.08 V/m

Now, the potential difference between the plates separated by a distance 'd' is given as:

ΔV = Ed

where E is the electric field

           d is the distance of separation between the plates

Applying values in the above equation we get:

ΔV = (418.08 V/m) × (0.09 m)

     = 37.63 V

Therefore, the magnitude of the electric potential difference between the plates is 37.63 V.

Learn more about electric potential difference here:

https://brainly.com/question/13296426

#SPJ4

Car A is traveling with a constant speed of 80 km>h due north, while car B is traveling with a constant speed of 100 km>h due east. Determine the velocity of car B relative to car A

Answers

Answer:

80J

Explanation:

K.E = ½ mv²

k.e = ½ * 80*

100²

ke= 4*20

ke= 80 J

The lion has a kinetic energy of 5000 j. What is the speed of the lion?

Answers

The lion has a kinetic energy of 5000 j, the speed of the lion is  v = 100 / [tex]\sqrt{M1}[/tex]  m/s

What is kinetic energy ?

Kinetic energy is a form of energy that an object or a particle has by reason of its motion. If work, which transfers energy, is done on an object by applying a net force, the object speeds up and thereby gains kinetic energy or Kinetic energy is the energy that an object possesses due to its motion. It is basically the energy of mass in motion. Kinetic energy can never be negative and it is a scalar quantity i.e. it provides only the magnitude and not the direction.

given

kinetic energy = 5000 J

speed = ?

since , mass is not given in the question

Let mass of lion will be = M1

kinetic energy = 1/2 * M1 * [tex]v^{2}[/tex]

             5000 J = 1/2 * M1 *  [tex]v^{2}[/tex]

             [tex]v^{2}[/tex] = [tex]\sqrt{10,000 / M1}[/tex]  m/s

              v = 100 / [tex]\sqrt{M1}[/tex]  m/s

The speed of the lion =  v = 100 / [tex]\sqrt{M1}[/tex]  m/s

To learn more about kinetic energy

https://brainly.com/question/12669551?referrer=searchResults

#SPJ4

In order to use the efficiency of a car engine in an optimal way, a maximum engine speed of .........rpm for shifting is recommended for gas engines.

Answers

In order to use the efficiency of a car engine in an optimal way, a maximum engine speed of 2,500 rpm for shifting is recommended for gas engines.

The maximum thermal efficiency of modern gasoline engines is over 50%, but legal cars on the road are only about 20% to 35% when used to power cars.

Unfortunately, even with regular car maintenance such as tuning and oil changes, the efficiency of today's gasoline engines is about 30-35%. In other words, about 65 cents per dollar spent on gasoline is wasted.

EPA's 2020 Automotive Trend Report preliminary data shows that the average fuel economy of 2020 model light trucks has increased to 25.7 miles per gallon (MPG). If this preliminary data holds, it will mark the highest average fuel economy ever for a new light commercial vehicle.

Learn more about the efficiency of a car engine here:https://brainly.com/question/11775858

#SPJ4

Normal human body temperature is 98.6°F. What is this temperature expressed in Celsius (°C) and in Kelvin (K)?

Answers

Answer: 37 Celsius and 310.15 K

Explanation:

C/5 = (F-32)/9 = (98.6-32)/9 = 66.6/9 = 7.4

C = 7.4 * 5 = 37 so the temperature is 37 Celsius

K = C + 273.15 = 37 + 273.15 = 310.15 K

Some fish have a density slightly less than that of water and must exert a force (swim) to stay submerged. What force must an 85.0-kg grouper exert to stay submerged in salt water if its body density is

Answers

The force require to keep grouper submerged is 8.207N.

According to Archimedes principle  buoyant force of any object must equal to weight of fluid it displaced.

The expression for the force exerted to stay submerged in salt water is

           F = F(b) - w(fish)

 where F(b) = buoyant force

              w(fish) = weight

      now substitute w(b) for F(b)

   →  F = Vρg - w(fish)

where  V = volume of sea water

             ρ = density of sea water

Now by Archimedes principle   V = m(fish)  / ρ(fish)

    →    F = (m(fish) / ρ (fish) ) ρg - m(fish)g

           F =   (85 kg/1015 kg-m^-3) (1.025× 10³ kg-m^-3) (9.8 m/s^2)

                                  -   (85kg)  × 9.8 m/s^2

           F = 841.207N - 833N

           F = 8.207 N

  Hence, the force require to keep grouper submerged is 8.207N.

    Learn more about Archimedes Principle here:

         https://brainly.com/question/15076878

              #SPJ4

Which of the zodiac constellations will be highest at midnight?

Answers

Answer:

Virgo will be the highest zodiac constellations at night.

2) Which pattern of organization did Alicia choose for her speech outline?

Answers

The pattern of organization Alicia chose for her speech outline is referred to as topical.

What is Topical pattern of organization?

This type of organization involves the arrangement of subtopics within a large or broad topic.

Alicia talked about speech pathology and the different subtopics include challenges, therapy etc which depicts topical pattern.

Read more about Topical pattern of organization here https://brainly.com/question/12235209

#SPJ1

question down below need rply fast

Answers

The resultant magnitude and direction of the vectors are as follows:

A. A = 6.6; θ = 30.8° from the x-axisB. B = 10.4; θ = 196.7° from the x-axisC. C = 23.3; θ = 300° from the x-axisD. D = 40.4; θ = 138° from the x-axisE. E = 49.5; θ = 346° from the x-axis

What is the resultant magnitude and direction of the given vectors?

The resultant magnitude and direction of the vectors are as follows:

A. A = √(5.7² + 3.4²)

A = 6.6

θ = tan⁻¹(3.4/5.7)

θ = 30.8° from the x-axis

B. B = √{(-10)² + (-3²)}

B 10.4

θ = tan⁻¹(3/10) + 180

θ = 16.7° + 180°

θ = 196.7° from the x-axis

C. C = √{(12)² + (-20²)}

C = 23.3

θ = 360° - tan⁻¹(20/12)

θ = 300° from the x-axis

D. D = √{(-30)² + (27²)}

D = 40.4

θ = 180 - tan⁻¹(27/30)

θ = 138° from the x-axis

E. E = √{(48)² + (12²)}

E = 49.5

θ = 360° - tan⁻¹(12/48)

θ = 346° from the x-axis

In conclusion, the resultant of the vectors and direction are obtained using the resultant vector formula.

Learn more about resultant of vectors at: https://brainly.com/question/12534255

#SPJ1

Two men standing on the same side of wall and at the same distance from It, such that they are 4oom apart when one fires a gun the other hears the first report in 1.2s and the second in 0.5s after the first. calculate 1) Velocity of sound in air . 2)the perpendicular distance of the men from the wall.

Answers

Answer:

1. 571.43m/s

2. 142.9m and 342.9m

Explanation:

1.Take the difference in time.

1.2-0.7=0.7 seconds

Take the distance between them and divide with differnce in time.

400÷0.7=571.43 seconds.

2.Take the time of the two men and divide by two.

0.5÷2= 0.25 secs

1.2÷2= 0.6 secs

multiply each with the velocity.

0.25×571.43=142.9m

0.6×571.43=342.9m

What is the energy of an electromagnetic wave that has a wavelength of
7.0 x 10-12 m? Use the equation E= hc where hc = 1.99 × 10-25 J-m.
OA. 2.8 × 10-14 J
OB. 1.4 x 10-36 J
OC. 9.0 x 10-37 J
OD. 7.2 x 1035 J
SUBMIT

Answers

[tex] {\qquad\qquad\huge\underline{{\sf Answer}}} [/tex]

Here we go ~

[tex]\qquad \sf  \dashrightarrow \:E = \dfrac{hc}{\lambda} [/tex]

here,

[tex] \sf{hc = 1.99 × {10}^{-25} J - m} [/tex]

[tex] \sf{\lambda = 7.0 × {10}^{-12}} [/tex]

____________________________________

[tex]\qquad \sf  \dashrightarrow \: E = \cfrac{1.99 \times 10 {}^{ - 25} }{7 \times 10 {}^{ - 12} } [/tex]

[tex]\qquad \sf  \dashrightarrow \: E= \cfrac{1.99}{7} \times 10 {}^{ (- 25 + 12)} { } [/tex]

[tex]\qquad \sf  \dashrightarrow \:E= 0.284 \times 10 { }^{ - 13} [/tex]

[tex]\qquad \sf  \dashrightarrow \: E= 2.84 \times 10 { }^{ - 14\:\; } J\: \: [/tex]

so, correct choice is A

When a 3.0 N weight is attached to a vertical coil spring, it stretches 5.0 cm. What weight would be required to stretch the spring 12.5 cm?
Group of answer choices

a. 7.5 N

b. 15 N

c. 4.5 N

d. 1.2 N

Answers

The weight required to stretch the spring 12.5 cm is 7.5 N (Option A)

Data obtained from the questionInitial weight (W₁) = 3 N Initial Length (L₁) = 5 cmNew length (L₂) = 12.5 cmNew Weight (W₂) =?

How to determine the new weight

The new weight required to stretch the spring can be obtained as follow:

W₁ / L₁ = W₂ / L₂

3 / 5 = W₂ / 12.5

Cross multiply

W₂ × 5 = 3 × 12.5

Divide both sides by 5

W₂ = (3 × 12.5) / 5

W₂ = 7.5 N

Learn more about spring constant:

https://brainly.com/question/9199238

#SPJ1

A proton exits the cyclotron 1. 0 ms after starting its spiral trajectory in the center of the cyclotron. How many orbits does the proton complete during this 1. 0 ms ?.

Answers

(a) The diameter of the largest orbit just before the protons exit the cyclotron is 39 cm.

(b) The number of orbits completed by the proton during this 1.0 ms is 14000 revolutions.

What is  kinetic energy?

The kinetic energy of an object is the energy that it possesses due to its motion.

It is defined as the work needed to accelerate a body of a given mass from rest to its stated velocity.

Formula of KE:

K.E = 1/2mv²

mv² = 2 K.E

v = sqrt( 2*KE / M)

Here,

(a)

The KE of the medical isotopes = 6.5 MeV

substituting the values,

v = sqrt( 2* 6.5* 1.6* 10^-13 / 1.67* 10^-27 )

v = 3.53 × 10⁷ m/s

Now the centripetal force:

mv² / R = qvB

r = q*v / mv²

r = ( 1.67* 10^-27 * 3.53 × 10⁷ ) / ( 1.9* 1.6* 10^-19 )

r = 0.19415 m

diameter d = 2r,

d= 2(0.19415  m)

d= 0.39 m ≅ 39 cm

(b)

The time period to complete a revolution around the spiral trajectory is:

T = 2πr / v

T = 2*3.14* 0.1941 / 3.53*10^7

T = 0.7 × 10⁻⁷ s

Thus, the number of orbits that the proton does to complete the revolution in 1 ms is:

n = t / T

n = 10^-3 / (0.7*10^-7)

n = 14285.71  ≅ 14000 revolutions

Learn more about spiral trajectory here:

https://brainly.com/question/8861443

#SPJ4

Your question is incomplete, but most probably full question was:

A medical cyclotron used in the production of medical isotopes accelerates protons to 6.5 MeV. The magnetic field in the cyclotron is 1.9 T.

(a) What is the diameter of the largest orbit, just before the protons exit the cyclotron? Express your answer with the appropriate units. d = 57 cm Previous

(b) A proton exits the cyclotron 1.0 ms after starting its spiral trajectory in the center of the cyclotron. How many orbits does the proton complete during this 1.0 ms?

what behavior is mostly strongly associated with introversion in a personality.

Answers

Answer:

Need quiet to concentrate

Are reflective

Are self-aware

Take time making decisions

Feel comfortable being alone

Don’t like group work

Prefer to write rather than talk

And maybe even feel tired after being in a crowd

Explanation:

What is the acceleration of a 2-kg mass if a 100-N force acts on it?

Answers

SOLUTION:

Acceleration = Force/mass

= 100N / 2 kgs

= 50 m/s

.

.

________________________________

HOPE IT HELPS

HOPE IT HELPS MARK BRAINLIEST!

FOLLOW ME!

Two objects X and Y move directly towards each other. The objects have the same mass.
Object X has a velocity of 5.0 m/s to the right. Object Y has a velocity of 3.0 m/s to the left.
Object X and object Y collide and stick together.
What is their velocity after colliding?

Answers

X and Y are two things that travel in the same direction. The mass of the things is the same. 5.0 m/s is the velocity of object x as it moves to the right. The velocity of object y to the left is 3.0 m/s. Objects x and y collide and adhere to one another. Following their collision, they both move at a speed of 1.0 m/s to the right.

Their velocity after colliding is 1.0 m / s to the right.

What is the velocity during the collision?

In a collision, the velocity change is always computed by subtracting the initial value from the final value. If an object is moving in one direction before a collision and rebounds or somehow changes direction, then its velocity after the collision has the opposite direction as before.Inelastic collisions occur when only the momentum is conserved but not the system's kinetic energy. Perfectly inelastic collisions happen when objects stick together and have a common velocity after collision. To solve for the final velocity in perfectly inelastic collisions, use v' = (m1v1 + m2v2)/m1 + m2.The magnitude of the relative velocity is the same before and after the collision.

To learn more about velocity, refer to:

https://brainly.com/question/25749514

#SPJ9

If a car increases its velocity from zero to 60 km/h in 10 seconds, its acceleration is______.

Answers

Answer:

1.66m/s

Explanation:

here

initial velocity(u): 0m/s

final velocity (v):60km= 60×1000/60×60

:16.6m/s

time taken(t): 10s

now

acceleration:v-u/t

or a: 16.6-0/10

:16.6/10

acceleration: 1.66 m/s

In physics, acceleration is the rate at which the velocity of an object changes in relation to time. The sum of all forces exerted on an object results in its acceleration. The acceleration is  1.66 m/s².

The rate at which velocity, either in terms of speed or direction or both, varies over time is known as acceleration. A circle's motion accelerates despite its constant speed because its direction is continually shifting.

Here

initial velocity(u) = 0m/s

final velocity (v) = 60km

v = 60 × 1000 / 60 × 60

v = 16.6 m/s

Time taken(t) =  10s

Now.

acceleration =  v-u / t

a = 16.6-0/10

a = 16.6/10

a = 1.66 m/s²

To know more about acceleration, visit;

https://brainly.com/question/29766852

#SPJ7

A man pushes a box across a floor. as he increases the force he applies horizontally to the box

a) the kinetic friction decreases
b) the kinetic friction may increase or decrease depending on the velocity of the box
c) the kinetic friction remains the same
d) the kinetic friction increases

Answers

When a man pushes a box across a floor, as he increases the force he applies horizontally to the box, then the kinetic friction remains the same.

To find the answer, we need to know about friction.

What is friction?Whenever a body moves, over the surface of another body, a force comes into play which acts parallel to the surface of contact and opposes the relative motion. This opposing force is called friction.There are two frictions acting on a surface.Static friction:  It come into play between two bodies before when it starts moving. Self-adjusting force and the max value of it is called limiting static friction.Kinetic friction:  It come into play between two bodies when it starts moving. It is not a self-adjusting force.As we increase applied force, kinetic friction will remain same.

Thus, we can conclude that, kinetic friction remains the same when we increase the applied force.

Learn more about the friction here:

https://brainly.com/question/28048527

#SPJ1

As a guy pushes a box across a floor, the kinetic friction stays constant no matter how much force is applied on the box horizontally.

We must understand friction if we are to find the solution.

Describe friction?A force that works parallel to the surface of contact and opposes the relative motion is always present whenever a body moves over the surface of another body. Friction is the name for this opposing force.On a surface, there are two frictions operating.Static friction: It occurs between two bodies before motion is initiated. Limiting static friction is the term used to describe the maximum amount of self-adjusting force.As soon as two bodies begin to move, kinetic friction is triggered. It is not a force that adjusts itself.The amount of kinetic friction will not change when we apply more force.

We can therefore draw the conclusion that kinetic friction does not change as the applied force is increased.

Learn more about the friction here:

brainly.com/question/28048527

#SPJ1

Other Questions
inflammation and edema of the optic disk is known as ________. Solve the given differential equation subject to the indicated conditions.y'' + y = sec3 x, y(0) = 2, y'(0) = 5/2 the 26 letters of the alphabet are placed on tiles and randomly separated into 2 equal piles. What is the probability that the word MATH can be found in one of the 2 piles? An arrow is shot into a hollow pipe resting on a horizontal table and flies out the other end. While the arrow travels in the pipe, its feathers brush against the walls of the pipe. (a) Which type of collision is the arrow-pipe interaction: elastic, inelastic, or totally inelastic? (b) Is there an instant when the velocity of the arrow relative to the pipe is necessarily zero? (c) Describe the energy conversions in the pipe-arrow system. Johanna spun a spinner 66 times and recorded the frequency of each result in the table. What is the theoretical probability of spinning an odd number? Write your answer using a / to represent the fraction bar. Can someone help me with this question pls and thank you. (: Do you think the weight of the melted sugar will equal the weight of the original sugar? In beta oxidation of linoleic acid, what is the cost in total ATPs for the presence of the two double bonds compared to the saturated carbon chain stearic acid? (hint: how many more electron carriers is produced in beta oxidation for stearic acid vs linoleic acid and how does that affect # of ATPs) Which of the following economic factors contributed to the changes in the urban population in Great Britain as described in the passage? like human capital theory, the dual labor market perspective posits the existence of two quite distinct labor markets (the primary labor market and the secondary labor market) that operate according to different rules. true or false Which of the following is NOT an element necessary for achieving the relaxation response?a. a quiet environmentb. a passive attitudec. a mental deviced. a comfortable positione. a mantra 3.3.420+5-43 calculate T/F the denominator in the formula for calculating the return on investment includes operating and nonoperating assets. you push your 0.70-kg pillow across your bed with a constant force of 12 n . the bed provides a frictional force of 8.0 n .What is the acceleration of the center of mass of the pillow? Assume that the direction of your push is the positive direction. chromosomes are present as attached sister chromatids in which stages? i. metaphase ii. telophase iii. prophase iv. anaphase prove or disprove: there exists i such that si > a. what proof technique did you use? a company budgets production of 4,870 units for june. each unit uses 2 hours of direct labor at $40 per hour. prepare a direct labor budget for june. When a consumer purchases products occasionally or needs information about an unfamiliar brand in afamiliar product category, he or she will most likely engage ina) enduring purchase behavior.b) routinized response behavior.c) extended problem solving.d) impulse searching.e) limited problem solving. Calculate the molarity of 75.0 ml. of a solution that is 0.92 % by mass NaCl. Assume the density of the solution is the same as pure water 0.213333 M 7th attempt Feedback The Mackenzie River in northern Canada contains, on average, 0.820 mM Ca2+ 0.430 mM Mg2+ 0.300 mm Na 0.0200 mMK 0.250 mMCI 0.380 mM SO42- and 1.82 mM HCO3 What, on average, is the total mass of these ions in 4.00 L of Mackenzie River water? X 51 TRUE/FALSE. The purpose of late hopping is to allow the oils to survive. what is the charge density that would create an electric current density given by vector J(x, y, z, t) = (z cap x - 4y^2 cap y + 2 x cap z) cos omega t [A/m^2]