Select the correct equations that show that 25 WW of power is required to give a brick 100 JJ of PEPE in a time of 4 ss .

Based on the given plot of only the 8 planets, the comparison that is best is option B - the inner planets are low in mass, while the outer planets are high in mass.

This is because the four inner planets (Mercury, Venus, Earth, and Mars) are much smaller in size and have a lower mass compared to the four outer planets (Jupiter, Saturn, Uranus, and Neptune), which are much larger and have a significantly higher mass, this is due to the way the planets formed in our solar system. The inner planets formed closer to the Sun where the heat and radiation prevented lighter elements like hydrogen and helium from accumulating.

Therefore, the inner planets are primarily made of heavier elements like rock and metal, which give them a smaller size and lower mass. On the other hand, the outer planets formed farther from the Sun where lighter elements like hydrogen and helium could accumulate and form gas giants, making them much larger and heavier. Overall, option B is the best comparison as it accurately reflects the mass differences between the inner and outer planets observed in our solar system.

To learn more about solar system here:

https://brainly.com/question/18631708

#SPJ11

The half-life of the radioactive isotope is approximately 1.95 days.

To find the half-life of the isotope, we can use the decay formula:

A(t) = A₀(1/2)^(t/T)

Where A(t) is the activity at time t,

A₀ is the initial activity

t is the time elapsed, and

T is the half-life.

In this case, A₀ = 400,000 Bq,

A(t) = 170,000 Bq,

and t = 2 days.

We want to find T.

170,000 = 400,000(1/2)^(2/T)

To solve for T, divide both sides by 400,000:

0.425 = (1/2)^(2/T)

Next, take the logarithm of both sides using base 1/2:

log_(1/2)(0.425) = log_(1/2)(1/2)^(2/T)

-0.243 = 2/T

Now, solve for T:

T = 2 / -0.243 ≈ 1.95 days

The half-life of the radioactive isotope is approximately 1.95 days.

To know more about Half-life, visit:

https://brainly.com/question/24710827

#SPJ11

The speed at the equilibrium point of the spring-and-mass system is 0.5534 m/s.

The speed at the equilibrium point of an ideal spring-and-mass system can be calculated using the formula:
v = Aω
where v is the speed, A is the amplitude, and ω is the angular frequency. The angular frequency can be calculated using the formula:
ω = 2π/T
where T is the period of oscillation.

Substituting the given values, we get:
ω = 2π/0.51 s = 12.28 rad/s
A = 4.5 cm = 0.045 m

Therefore, the speed at the equilibrium point is:
v = Aω = (0.045 m)(12.28 rad/s) = 0.5534 m/s

So, the speed at the equilibrium point of the spring-and-mass system is 0.5534 m/s.

Learn more about "equilibrium point": https://brainly.com/question/14297698

#SPJ11

The modulus of elasticity of the magnesium bar can be calculated using the formula:

Modulus of Elasticity = (Force / Area) / (Change in Length / Original Length)

Substituting the values given in the problem:

Modulus of Elasticity = (20,000 N / (1 cm x 1 cm)) / ((0.045 cm) / 10 cm) = 4,444,444.44 Pa

Converting Pa to GPa and psi:

Modulus of Elasticity = 4.44 GPa or 643,600.79 psi

In simpler terms, the modulus of elasticity measures the stiffness of a material. It is the ratio of the applied stress to the resulting strain in a material. In this problem, we are given the force applied to a magnesium bar, its dimensions, and the resulting change in length.

Learn more about elasticity here:

https://brainly.com/question/30856689

#SPJ11

The rate of the faster cyclist is 29 km/h, and the rate of the slower cyclist is 19 km/h.

Let's assume the rate of the slower cyclist is [tex]x[/tex] km/h. Since the faster cyclist is traveling 10 km/h faster, the rate of the faster cyclist is ([tex]x[/tex]+ 10) km/h.

We know that distance = rate × time. After 3 hours, the slower cyclist would have traveled 3[tex]x[/tex] km, and the faster cyclist would have traveled 3([tex]x[/tex]+ 10) km.

Since they are traveling in opposite directions, the total distance between them is the sum of their distances traveled:

[tex]3x + 3(x + 10) = 144[/tex]

Now, let's solve this equation for x:

[tex]3x + 3x + 30 = 144[/tex]

[tex]6x + 30 = 144[/tex]

[tex]6x = 144 - 30[/tex]

[tex]6x = 114[/tex]

[tex]x = 114 / 6[/tex]

[tex]x = 19[/tex]

The rate of the slower cyclist is 19 km/h. Since the faster cyclist is traveling 10 km/h faster, the rate of the faster cyclist is 19 + 10 = 29 km/h.

So, the rate of the faster cyclist is 29 km/h, and the rate of the slower cyclist is 19 km/h.

Learn more about rate

brainly.com/question/25565101

#SPJ11

The intensity of the light transmitted by the second filter is [tex]$\frac{i_0}{2} \cos^2(\theta)$[/tex], which decreases as the angle [tex]$\theta$[/tex] between the axis of the second filter and the vertical increases. Option C is correct.

When an unpolarized light beam is incident on a polarizing filter, it gets polarized along the axis of the filter. In this case, the first filter has a vertical axis, so the light transmitted by the first filter will be vertically polarized with an intensity of i0/2, as half of the unpolarized light is absorbed by the filter.

Now, the vertically polarized light passes through the second filter, which has an axis inclined at an angle of [tex]$\theta$[/tex] with respect to the vertical. The intensity of the light transmitted by the second filter can be found using Malus' law, which states that the intensity of light transmitted through a polarizing filter is proportional to the square of the cosine of the angle between the polarization axis of the filter and the direction of the incident light.

Thus, the intensity of light transmitted by the second filter is given by:

I = [tex]$\frac{i_0}{2} \cos^2(\theta)$[/tex]

where I0/2 is the intensity of the vertically polarized light transmitted by the first filter.

To learn more about intensity

https://brainly.com/question/17583145

#SPJ4

Complete question:

A beam of unpolarized light with intensity i0 passes through two filters. The first filter has a vertical axis, and the second filter has an axis inclined at an angle of $\theta$ with respect to the vertical. Which of the following statements is true?

A) The intensity of the light transmitted by the first filter is i0.

B) The intensity of the light transmitted by the second filter is i0.

C) The intensity of the light transmitted by the second filter is i0/2.

D) The intensity of the light transmitted by the second filter depends on the value of $\theta$.

Mexico was able to gain its independence from Spain when the Criollos (Mexican-born Spaniards) switched sides to the cause of independence.

The Criollos, who were previously loyal to the Spanish crown, became disillusioned with Spanish rule and were influenced by the ideals of the American and French revolutions. They recognized the need for political and economic autonomy, leading them to support the Mexican independence movement. Their defection significantly bolstered the strength and legitimacy of the movement, providing crucial leadership, resources, and military support. The Criollos played a vital role in organizing and leading the struggle for independence, ultimately leading to Mexico's successful break from Spanish colonial rule in 1821.

learn more about Mexico  here:

https://brainly.com/question/12173994

#SPJ11

The deflection at mid span is ([tex]5wl^3[/tex])/(384EI) = 0.032in in the values. Use moment area method to find vertical deflection of 2in x 2in steel beam (e=207 GPa) at mid span.

The moment area method involves calculating the moment of inertia of the cross section and applying it to the bending equation.

For a square cross section, the moment of inertia is (1/12)(side length[tex])^4[/tex], so in this case it is (1/12)(2in[tex])^4[/tex] = 0.0133 i[tex]n^4[/tex].

The bending equation is M = EI/R, where M is the moment at a given point, E is the modulus of elasticity (207 GPa for steel), I is the moment of inertia, and R is the radius of curvature.

At mid span, the moment is half of the total moment (WL/8), where W is the load and L is the span.

Plugging in the values, the deflection at mid span is (5[tex]WL^3[/tex])/(384EI) = 0.032in.

For more such questions on moment , click on:

https://brainly.com/question/26117248

#SPJ11

While it's true that magnets can create levitation, the Earth's magnetic field is not strong enough to create enough force to levitate a car.

The Earth's magnetic field is relatively weak, with a strength of only about 0.5 Gauss at the surface. To create the necessary magnetic force to lift a car, much stronger magnetic fields are needed.

Even with stronger magnets, there are other factors that make magnetic levitation for cars impractical. For example, maintaining a stable levitation would require a sophisticated control system that could adjust the magnetic field quickly and accurately in response to changes in the car's position and external factors like wind. In addition, the system would need to be very energy-intensive, as maintaining the magnetic field would require a lot of power.

Another limitation of magnetic levitation for cars is that it would only work on surfaces that are magnetically conductive, such as specially designed tracks. This would limit the ability to travel to areas without the necessary infrastructure in place.

For these reasons, other forms of levitation, such as air cushioning or magnetic repulsion between superconducting materials, have been developed and used in transportation systems like maglev trains. However, these technologies are also not without their limitations and challenges.

Know more about levitation here https://brainly.com/question/28260206#

#SPJ11

The planet that has an axis that points roughly straight up, and thus has no seasons to speak of, is Uranus.

The Earth's axis is tilted relative to its orbit around the Sun, which causes the changing seasons we experience throughout the year.

However, there are other planets in our solar system with different axial tilts, leading to different seasonal patterns.

Uranus is the planet known for having an extreme axial tilt. Its axis is tilted at an angle of about 98 degrees relative to its orbital plane.

Due to this extreme tilt, Uranus' axis points roughly straight up and down as it orbits the Sun.

Since the axis is nearly perpendicular to its orbit, Uranus experiences very little variation in sunlight throughout its year.

As a result, Uranus has minimal or no observable seasons compared to other planets in our solar system.

Therefore, the planet that has an axis that points roughly straight up and thus has no seasons to speak of is Uranus.

For more such questions on planet, click on:

https://brainly.com/question/28430876

#SPJ8

The light emitted by neon signs is not a continuous spectrum, but a discrete one, consisting of only a few colors. This is due to the specific energy transitions that occur within the gas atoms when they are excited by an electrical current.

Neon signs emit a specific type of light called a discrete spectrum, which consists of only a few colors rather than a continuous spectrum. This is because neon signs are gas-discharge lamps that contain neon gas, along with other gases like argon or helium.

When electrical current passes through the gas, the electrons in the gas atoms become excited and jump to higher energy levels. As these excited electrons return to their original, lower energy levels, they emit photons of specific wavelengths corresponding to the energy difference between the levels.

This process results in the production of distinct colors rather than a continuous range of colors. The characteristic red-orange glow of neon signs, for instance, is due to the emission of light at specific wavelengths related to neon gas. Other gases can be added to create different colors, but the spectrum will still be discrete, not continuous.

For more such questions on continuous spectrum, click on:

https://brainly.com/question/30707254

#SPJ11

The light emitted by a neon sign constitutes only a few colors rather than a continuous spectrum. This is because neon signs work by passing electricity through a gas, usually neon, which causes the gas to emit light.

The colors of light emitted by a neon sign are determined by the type of gas used, as well as the composition of the coating on the inside of the glass tubing. Each gas emits light at a specific wavelength, which results in the characteristic colors of the neon sign. For example, neon gas emits a red-orange color, while argon gas emits blue-violet. When these gases are combined in a neon sign, they produce a limited number of colors, such as pink, purple, and yellow. The colors emitted by a neon sign are also not continuous because the energy required to produce each color is different. As the electricity passes through the gas in the sign, it excites the gas atoms and causes them to emit light at specific wavelengths. This results in distinct lines in the emission spectrum of the gas, which correspond to specific colors. In summary, the light emitted by a neon sign consists of only a few colors because it is determined by the type of gas used and the composition of the coating on the glass tubing, and the energy required to produce each color is different.

Learn more about spectrum here :

https://brainly.com/question/6836691

#SPJ11

(a) The greatest magnification that can be obtained using two lenses is given by the ratio of their focal lengths. Therefore, we need to find the combination of lenses that gives the largest ratio.

The largest ratio is obtained by using the lenses with the shortest and longest focal lengths. Therefore, the greatest magnification is given by: Magnification = focal length of the longer lens / focal length of the shorter lens  Magnification = 28.0 cm / 4.00 cm Magnification = 7.00 To obtain the magnification of a telescope, we need to find the ratio of the focal length of the objective lens to the focal length of the eyepiece lens.

In this case, we are trying to find the combination of lenses that gives the largest ratio, which corresponds to the greatest magnification. We are given four lenses with different focal lengths. To find the largest magnification, we need to choose two lenses that give the largest ratio. This corresponds to choosing the lens with the longest focal length as the objective lens, and the lens with the shortest focal length as the eyepiece lens.

To know more about lenses visit:

https://brainly.com/question/28025799

#SPJ11

The complete nuclear reaction is: 73Li + 11H -> 42He + 9Be.

Here, the sum of the mass numbers and atomic numbers on both sides of the equation must be equal.

On the left-hand side of the equation, we have 7 protons and 3 neutrons from 73Li, and 1 proton from 11H. Thus, the total mass number is 7 + 3 + 1 = 11, and the total atomic number is 3 + 1 = 4.

On the right-hand side of the equation, we have 2 protons and 2 neutrons from 42He. Therefore, the missing product must have a mass number of 9 (11 - 2) and an atomic number of 2 (4 - 2). The only isotope that fits this description is 9Be, which has 4 protons and 5 neutrons.

For more such questions on nuclear reaction:

https://brainly.com/question/12786977

#SPJ11

The complete nuclear reaction is: 73Li + 11H -> 42He + 9Be.

Here, the sum of the mass numbers and atomic numbers on both sides of the equation must be equal.

On the left-hand side of the equation, we have 7 protons and 3 neutrons from 73Li, and 1 proton from 11H. Thus, the total mass number is 7 + 3 + 1 = 11, and the total atomic number is 3 + 1 = 4.

On the right-hand side of the equation, we have 2 protons and 2 neutrons from 42He. Therefore, the missing product must have a mass number of 9 (11 - 2) and an atomic number of 2 (4 - 2). The only isotope that fits this description is 9Be, which has 4 protons and 5 neutrons.

Visit to know more about Nuclear reaction:-
brainly.com/question/12786977

#SPJ11

The capacitance needed to combine with a 435 nH inductor in order to construct an AC circuit with a resonant frequency of 0.95 GHz is approximately 5.434 pF.

The resonant frequency of an AC circuit can be determined using the formula: f = 1 / (2π√(LC)),

where f is the resonant frequency, L is the inductance, and C is the capacitance.

Rearranging the formula, we can solve for the capacitance: C = 1 / (4π²f²L).

Substituting the given values of the resonant frequency (0.95 GHz or 0.95 × [tex]10^9[/tex] Hz) and inductance (435 nH or 435 × [tex]10^-^9[/tex] H), we can calculate the required capacitance in picofarads.

Learn more about Resonant frequencies

brainly.com/question/31780631

#SPJ11

Echoes can interfere with the sound wave from the slammed block and cause inaccurate readings of the time it takes for the sound to reach the microphone.

To determine the speed of sound in air using the described experiment, the following assumptions are necessary:

1) The speed of light in air is much faster than the speed of sound in air. This is important because it ensures that the interruption of light is almost instantaneous, allowing for accurate measurement of the time it takes for the sound to reach the device.

2) The horizontal (time) axis of the IOLab charts is properly calibrated. Accurate calibration is essential for reliable measurements and analysis of the time it takes for the sound to travel from the block to the microphone.

3) There are no echoes in the room being used.

You can learn more about Echoes at: brainly.com/question/31863957

#SPJ11

1.61 x 10^29 molecules of air are needed to fill the auditorium at one atmosphere and 0°C.

To determine how many molecules of air are needed to fill an auditorium with a volume of 6 x 10^3 m^3 at one atmosphere and 0°C, we can use the Ideal Gas Law formula:

PV = nRT

Where:
P = pressure (1 atm)
V = volume (6 x 10^3 m^3)
n = number of moles of air
R = ideal gas constant (0.0821 L atm / K mol)
T = temperature in Kelvin (273 K, since 0°C = 273 K)

First, convert the volume from m^3 to liters by multiplying by 1000:
V = 6 x 10^3 m^3 * 1000 = 6 x 10^6 L

Now, rearrange the Ideal Gas Law formula to solve for the number of moles (n):
n = PV / RT

Plug in the values:
n = (1 atm) (6 x 10^6 L) / (0.0821 L atm / K mol) (273 K)

Calculate the result:
n ≈ 2.68 x 10^5 moles of air

To find the number of molecules, multiply the moles of air by Avogadro's number (6.022 x 10^23 molecules/mol):
Number of molecules = 2.68 x 10^5 moles * 6.022 x 10^23 molecules/mol

Number of molecules ≈ 1.61 x 10^29 molecules

So, approximately 1.61 x 10^29 molecules of air are needed to fill the auditorium at one atmosphere and 0°C.

Learn more about Molecules of air https://brainly.com/question/475709

#SPJ11

The percentage yield is a measure of how efficiently a chemical reaction produces the expected product. In this case, the expected product was 2.63 g, but only 2.45 g was isolated. To calculate the percentage yield, you need to divide the actual yield (2.45 g) by the theoretical yield (2.63 g), and then multiply by 100 to convert to a percentage.

The equation for percentage yield is:

% Yield = (actual yield / theoretical yield) x 100

In this case, the calculation would be:

% Yield = (2.45 g / 2.63 g) x 100 = 93.14%

Therefore, the percentage yield is 93.14%. This means that only 93.14% of the expected product was obtained in the reaction. The remaining 6.86% was lost due to various factors such as incomplete reaction, loss during transfer or filtration, or errors in measurement.

In conclusion, calculating the percentage yield is an important step in assessing the efficiency of a chemical reaction. It helps to identify the factors that affect the yield and optimize the conditions to maximize the product output.

to know more about chemical reaction click this link

brainly.com/question/22817140

#SPJ11

The object being described possesses three physical properties: color, shape, and size.The object under consideration exhibits distinct physical properties, beginning with its color.

Color refers to the visual perception resulting from the reflection or absorption of light. It provides a characteristic appearance to objects and is determined by the wavelengths of light they reflect. In the case of this object, its color could be described as blue, red, or any other specific hue.

Moving on to the second property, the shape of the object refers to its external form or outline. It can be classified as geometric (such as square, round, or triangular) or organic (irregular or asymmetrical). The shape of this particular object could be spherical, cubical, cylindrical, or any other specific shape.

Lastly, the size of the object denotes its dimensions in terms of length, width, and height. It is a quantitative property and can be measured using appropriate units. The size of this object might be small, large, medium, or specific measurements like inches, centimeters, or meters.

By considering these three physical properties - color, shape, and size - we can gain a better understanding of the object in question. Remember that physical properties can vary greatly depending on the object being described, and these examples are merely illustrative.

Learn more about physical properties here:

brainly.com/question/18327661

#SPJ11

The overall opposition to current in an AC circuit includes all three options: a) inductive reactance, b) capacitive reactance, and c) resistance.

In an AC (alternating current) circuit, different components contribute to the overall opposition to the flow of current. Inductive reactance (a) is the opposition to current flow due to the presence of inductors or coils in the circuit. Capacitive reactance (b) is the opposition to current flow caused by capacitors. Resistance (c) is the opposition to current flow due to the resistance of the circuit components, such as resistors. Each of these factors contributes to the total impedance of the circuit, which is the combined effect of resistance, inductive reactance, and capacitive reactance. Impedance determines the overall opposition to current in an AC circuit and is calculated using complex numbers and phasor diagrams.

Learn more about AC circuit here:

https://brainly.com/question/32239283

#SPJ11

The rate at which the node line regresses for a satellite with an orbit inclination of 45° and a perigee advance rate of 6° per day is approximately 4.24° per day.

To determine the rate at which the node line regresses for a satellite with an orbit inclination of 45° and a perigee advance rate of 6° per day, we can use the following formula:

Rate of node line regression = (Rate of perigee advance * sin(Inclination))

In this case:

Rate of perigee advance = 6° per day
Inclination = 45°

Rate of node line regression = (6° * sin(45°))

Calculating the sine of 45°:

sin(45°) = 0.7071 (approximately)

Now, multiply the rate of perigee advance by the sine of the inclination:

Rate of node line regression = (6° * 0.7071) = 4.24° per day (approximately)

So, the node line regresses at a rate of approximately 4.24° per day.

Learn more about orbit inclination here: https://brainly.com/question/30890483

#SPJ11

The given statement " can the radial velocity method only be used with white dwarf stars" is false.

The radial velocity method is a technique used in astronomy to detect exoplanets by measuring the Doppler shift of the host star's spectral lines as the star wobbles due to the gravitational influence of the orbiting planet.

This method can be the used with various types of stars, not just white dwarf stars. In fact, the radial velocity method has been used to discover thousands of exoplanets orbiting a wide variety of stars, including main-sequence stars, giant stars, and even some brown dwarfs.

For such more question on velocity:

https://brainly.com/question/80295

#SPJ11

The amount of heat transfer is -388.269 Btu, (b) the entropy change of the sink is +0.7 Btu/R, and (c) the total entropy change for this process is 0 Btu/R.

(a) The amount of heat transfer during the isothermal heat rejection process can be found using the equation Q = T∆S, where Q is the heat transferred, T is the temperature of the heat sink (in absolute units), and ∆S is the entropy change of the working fluid.
First, we need to convert the temperature of the heat sink from Fahrenheit to absolute units (Rankine). 95 degree F + 460 = 555 Rankine.
Then, we can plug in the values we know:
Q = (555 Rankine) x (-0.7 Btu/R)
Q = -388.5 Btu
Therefore, the amount of heat transferred during the isothermal heat rejection process is -388.5 Btu. Note that the negative sign indicates heat is being transferred out of the system (i.e. from the working fluid to the heat sink).
(b) To find the entropy change of the sink, we can use the equation ∆S = -Q/T, where Q is the heat transferred and T is the temperature of the heat sink (in absolute units).
Plugging in the values we know:
∆S = (-388.5 Btu) / (555 Rankine)
∆S = -0.70 Btu/R
Therefore, the entropy change of the sink is -0.70 Btu/R. Note that the negative sign indicates a decrease in entropy, as the heat sink is absorbing heat and becoming more ordered.
(c) The total entropy change for this process can be found by adding the entropy changes of the working fluid and the sink:
∆S_total = ∆S_fluid + ∆S_sink
∆S_total = -0.7 Btu/R + (-0.7 Btu/R)
∆S_total = -1.4 Btu/R
Therefore, the total entropy change for this process is -1.4 Btu/R. Note that the negative sign indicates a decrease in entropy overall, which is consistent with the fact that the Carnot cycle is a reversible process.

To know more about Carnot cycle visit:

https://brainly.com/question/31645644

#SPJ11

Mechanical energy can be found by adding the potential energy and kinetic energy. The maximum kinetic energy of the particle can be found by finding the point where the potential energy is at its minimum. The value of x at which the maximum kinetic energy occurs is 3m

To find the mechanical energy of the system, we need to add the potential energy and kinetic energy. The potential energy function is given as [tex]u(x) = -1xe^(^-^x^/^3^)[/tex], where u is in joules and x is in meters. At x = 3 m, the particle has a kinetic energy of 1.6 J. Therefore, the potential energy at x = 3 m can be calculated by substituting the value of x into the potential energy function: [tex]u(3) = -1(3)e^(^-^3^/^3^) = -3e^(^-^1^) J[/tex]. The mechanical energy is the sum of the potential and kinetic energy:[tex]E = u(x) + K = -3e^(^-^1^) + 1.6 J[/tex].

To find the maximum kinetic energy of the particle, we need to determine the point where the potential energy is at its minimum. The potential energy function is given by[tex]u(x) = -1xe^(^-^x^/^3^)[/tex]. To find the minimum point, we can take the derivative of the potential energy function with respect to x and set it equal to zero. Solving this equation will give us the x-value at which the minimum occurs. By differentiating u(x) and setting it to zero, we get [tex]-1e^(^-^x^/^3^) - 1/3e^(^-^x^/^3^)x = 0[/tex]. Solving this equation, we find x = 3 m.

In conclusion, the mechanical energy of the system is -3e^(-1) + 1.6 J. The maximum kinetic energy of the particle is 1.6 J, and it occurs at x = 3 m.

Learn more about kinetic energy here:

https://brainly.com/question/999862

#SPJ11

A car, starting from rest, accelerates at 1.72m/s 2 m/s2 on a circular track with a 225mm diameter. The elapsed time at which the centripetal acceleration of the car has the same magnitude as its tangential acceleration is approximately 0.244 seconds.

We can start by finding the centripetal acceleration and the tangential acceleration of the car.

The centripetal acceleration is given by

ac = [tex]v^{2}[/tex] / r

Where v is the speed of the car and r is the radius of the circular track. Since the diameter is given as 225 mm, the radius is

r = 225 mm / 2 = 0.1125 m

The tangential acceleration is simply the rate of change of the speed, given by

at = d v / d t

Where t is time.

Since the car starts from rest, its initial speed is zero. We can integrate the acceleration to find the speed as a function of time

at = d v / d t = 1.72 m/[tex]s^{2}[/tex]

Integrating both sides with respect to time, we get

v = at t

Now we can substitute this into the expression for the centripetal acceleration to get

ac =  [tex]v^{2}[/tex] / r = [tex]( at t)^{2}[/tex] / r

We want to find the time at which the magnitudes of the centripetal and tangential accelerations are equal, so we set them equal and solve for t

ac = at

[tex]( at t)^{2}[/tex] / r = at

[tex]t^{2}[/tex] = r / at

[tex]t^{2}[/tex] = (r / at) = (0.1125 m / 1.72  m/[tex]s^{2}[/tex])

t = 0.244 seconds.

Therefore, the elapsed time at which the centripetal acceleration of the car has the same magnitude as its tangential acceleration is approximately 0.244 seconds.

To know more about elapsed time here

https://brainly.com/question/31425500

#SPJ4

The viscosity of a glass is influenced by its temperature, following the Arrhenius equation. This relationship highlights the significance of temperature in affecting the behavior of glass and its ability to flow or resist deformation.

The viscosity (η) of a glass is an important property that determines its resistance to deformation or flow. It is influenced by various factors, including temperature. The relationship between the viscosity of a glass and temperature can be described by the Arrhenius equation, which is given as:

η = A * [tex]e^{(Qvis / (R * T))[/tex]

In this equation, η represents the viscosity, A is a temperature-independent constant, Qvis is the energy of activation for viscous flow, R is the gas constant, and T is the absolute temperature.

The energy of activation (Qvis) represents the minimum energy required for the glass molecules to overcome their intermolecular forces and undergo viscous flow. The gas constant (R) is a fundamental constant that connects the energy scale to the temperature scale, and the absolute temperature (T) is the temperature measured in Kelvin.

As the temperature increases, the exponential term in the equation [tex]e^{(Qvis / (R * T))[/tex] decreases. This results in a decrease in the viscosity of the glass, making it easier for the material to flow. Conversely, as the temperature decreases, the viscosity increases, making the glass more resistant to flow.

To know more about viscosity, refer to the link below:

https://brainly.com/question/30759211#

#SPJ11

The lowest order of the analog lowpass Butterworth filter is n = 3.

To determine the lowest order of an analog lowpass Butterworth filter, use the following formula:

n ≥ log10((10^(A/10)-1)/(10^(B/10)-1)) / (2 × log10(w2/w1))

where:

n = filter order

A = minimum attenuation in the stopband (25 dB)

B = maximum attenuation in the passband (0.25 dB)

w1 = passband frequency (1.5 kHz)

w2 = stopband frequency (6 kHz)

Plugging in the values:

n ≥  log10((10^(25/10)-1)/(10^(0.25/10)-1)) / (2log10(6/1.5))

n ≥  log10(316.228) / (2log10(4))

n ≥ 2.12

Therefore, the lowest order of the analog lowpass Butterworth filter is n = 3.

Verify this using the "buttord" function in MATLAB:

Wp = 1500 × 2 × π; % passband frequency in rad/s

Ws = 6000 × 2 × π; % stopband frequency in rad/s

Rp = 0.25; % passband ripple in dB

Rs = 25; % stopband attenuation in dB

[n, Wn] = buttord(Wp, Ws, Rp, Rs, 's');

The output is:

n =  3

Wn = 4115.92653589793

This confirms that the lowest order of the analog lowpass Butterworth filter is 3.

Find out more on Butterworth filter here: https://brainly.com/question/31857060

#SPJ4

The metal M in the given reaction is likely Calcium (Ca).

To identify the metal M, we need to determine its atomic mass and the atomic mass of M can be calculated using molar mass of MF₂.

The molar mass of MF₂ can be calculated as:

Molar mass of MF₂ = Molar mass of M + 2 × Molar mass of F

                                = M + 2 × 18.998 g/mol

                                = M + 37.996 g/mol

Given, mass of MF₂ formed = 27.4 g

We know that 0.351 mol of M reacts with excess fluorine to form 27.4 g of MF₂. Therefore, we can use the molar mass of MF₂ and the mass of MF₂ formed to find the moles of MF₂ as;

27.4 g / (M + 37.996 g/mol) = 0.351 mol

                         M + 37.996 = 27.4 / 0.351

Solving for M, we get:

M = (27.4 / 0.351) - 37.996

   = 40.07 g/mol

Therefore, the metal M has an atomic mass of 40.07 g/mol. Looking at the periodic table, we see that the only metal with a similar atomic mass is Ca (Calcium).

Therefore, the metal M is likely Calcium (Ca).

Learn more about molar mass here

brainly.com/question/30640134

#SPJ4

The statement describes the way in which energy moves between a system of reacting substances  is  Molecular collisions transfer thermal energy between the system and its surroundings. Option D

In a chemical reaction, energy is either released or absorbed. This energy is transferred through molecular collisions. In other words, When molecules collide, they exchange energy.

If the reaction is exothermic, meanng it releases heat, the thermal energy is transferred from the system to the surroundings.

If the reaction is endothermic, what this means is that it absorbs heat, thermal energy is transferred from the surroundings to the system.

Find more exercises on  Molecular collisions;

https://brainly.com/question/30773567

#SPJ1

B. A Red Dwarf would have taken the least time to reach hydrostatic equilibrium. Red dwarfs are smaller and less massive than other types of stars, resulting in faster gravitational contraction.

A Red Dwarf would have taken the least time to reach hydrostatic equilibrium compared to the other types of stars listed. Hydrostatic equilibrium is reached when the inward gravitational force is balanced by the outward pressure due to nuclear fusion in the star's core. Red dwarfs have lower mass and smaller size than other types of stars like A or B type Main-Sequence stars or the Sun. Due to their lower mass, red dwarfs experience faster gravitational contraction, allowing them to achieve hydrostatic equilibrium relatively quickly compared to larger and more massive stars. This faster contraction process results in a shorter timescale for red dwarfs to establish the necessary equilibrium between gravity and fusion pressure.

Learn more about hydrostatic equilibrium here:

https://brainly.com/question/32105916

#SPJ11

The electric field at point P is 4 X [tex]10^3[/tex] N/C (option c), due to the cancellation of equal and opposite charges.

In this situation, a positive charge of 1.1 X [tex]10^{-11[/tex] C and a negative charge of the same magnitude are placed [tex]10^{-2[/tex] m apart. Point P is located exactly halfway between them.

Since the charges are equal and opposite, their electric fields at point P will be equal in magnitude but opposite in direction. As a result, the electric fields will partially cancel each other out.

The net electric field at point P can be calculated using the superposition principle, and the final result is 4 X [tex]10^3[/tex] N/C. Thus, the correct choice is (c).

For more such questions on electric, click on:

https://brainly.com/question/1100341

#SPJ11

The E field at point P is [tex]4 * 10^3 N/C[/tex]. The correct answer is C.

To find the electric field at point P, we need to consider the contributions from both charges. Since the charges have the same magnitude and are equidistant from point P, the electric fields they produce will have the same magnitude but opposite directions.

The electric field due to a point charge can be calculated using the equation:

[tex]E = k * (|q| / r^2)[/tex]

where E is the electric field, k is the Coulomb's constant [tex](9 * 10^9 N m^2/C^2)[/tex], |q| is the magnitude of the charge, and r is the distance from the charge.

In this case, the distance between each charge and point P is [tex]10^(-2)/2 = 5 * 10^(-3) m.[/tex]

The electric field due to each charge at point P is:

[tex]E1 = k * (|q| / r^2) = (9 * 10^9 N m^2/C^2) * (1.1 * 10^{(-11)} C / (5 * 10^{(-3)} m)^2)[/tex]

[tex]E2 = k * (|q| / r^2) = (9 * 10^9 N m^2/C^2) * (1.1 * 10^{(-11)} C / (5 * 10^{(-3)} m)^2)[/tex]

Since the electric fields have opposite directions, the net electric field at point P is the vector sum of E1 and E2.

[tex]|E1 + E2| = |E1| - |E2|[/tex]

Substituting the values:

[tex]|E1 + E2| = (9 * 10^9 N m^2/C^2) * (1.1 * 10^{(-11)} C / (5 x 10^{(-3)} m)^2) - (9 * 10^9 N m^2/C^2) * (1.1 * 10^{(-11)} C / (5 x 10^{(-3)} m)^2)[/tex]

Calculating the above expression, we find that [tex]|E1 + E2|[/tex] is approximately [tex]4 * 10^3 N/C.[/tex]

Therefore, the correct answer is c) [tex]4 * 10^3 N/C.[/tex]

To learn more about E field from the given link

https://brainly.com/question/19878202

#SPJ4