The red curve shows how the capacitor charges after the switch is closed at t=0 Which curve shows the capacitor charging if the value of the resistor is reduced? - Q A B С D -0 t
Answers
The Curve C shows the capacitor charging if the value of the resistor is reduced.
If the value of the resistor is reduced, the capacitor will charge at a faster rate. This is because the time constant (RC) of the circuit will be decreased, where R is the resistance and C is the capacitance. The time constant represents the time it takes for the capacitor to charge to 63.2% of its maximum voltage when the switch is closed.
The curve that shows the capacitor charging if the value of the resistor is reduced would be curve C. This curve will have a steeper slope than the original curve (curve A) because the capacitor will be charging more quickly. The final voltage on the capacitor will be the same, but it will reach that voltage faster.
It is important to note that if the resistor is decreased too much, the circuit may become unstable and the capacitor may not charge properly. It is also important to ensure that the new resistor value is within the range of acceptable values for the circuit and that it can handle the power dissipation.
In summary, reducing the value of the resistor in a RC circuit will result in a faster charging time for the capacitor and a steeper slope in the charging curve, as seen in curve C. However, it is important to ensure that the new resistor value is within acceptable limits and that the circuit remains stable.
Know more about capacitor here:
https://brainly.com/question/21851402
#SPJ11
The Question was Incomplete, Find the full content below :
The red curve shows how the capacitor charges after the switch is closed at t=0 Which curve shows the capacitor charging if the value of the resistor is reduced?
Related Questions
The tub of a washing machine goes into its spin cycle, starting from rest and gaining angular speed steadily for 8.00 s, at which time it is turning at 6.00 rev/s. At this point, the lid of the washing machine is opened, and a safety switch turns it off. The tub then smoothly slows to rest in 11.0 s. Through how many revolutions does the tub rotate while it is in motion
Answers
Through 57 revolutions the tub rotate while it is in motion.
What is angular speed?
Angular speed is defined as the rate of change of angular displacement, It is a scalar measurement of rotating object.
It is expressed as follows: ω = θ / t.
Here,
Initially tub is at rest so,
ω(i) = 0 rev/s
ω(f) = 6 rev/s
time taken, t = 8 second
Now the total number of revolutions,
N = t * ( ω(i)+ ω(f) ) / 2
N1 = 8* ( 0+6 ) / 2
N1 = 24 rev
Now, when the lid is opened it's safety switch is off due to which it is uniformly decelerated and comes to rest in 11 s
N2 = 11* ( 0+6 ) / 2
N1 = 33 rev
So,
Total number of revolutions:
N = N1 + N2
N = 24 + 33
N = 57 revolutions
Thus,
Through 57 revolutions the tub rotate while it is in motion.
Learn more about angular speed here:
https://brainly.com/question/9684874
#SPJ4
Hi I need help with the question in the image, step by step. ASAP!, thank you.
Answers
The heating curve is a representation of temperature change for a body with time as shown on cartesian axes.
What is a heating curve?The heating curve is a representation of temperature change for a body with time as shown on cartesian axes.
The point A represents the steady increase in the temperature of the solid. The point B shows the point of fusion, at this point, the solid is transformed into liquid. The point C shows the temperature rise with time as the liquid is heated. The point D shows the process of vaporization which converts the liquid to gas. The point E shows when the substance now exists in the gas phase.
Learn kore about heating curve:https://brainly.com/question/10481356
#SPJ1
Hydrostatic equilibrium in the Sun means that Choose one: A. energy produced in the core per unit time equals energy emitted at the surface per unit time. B. pressure balances the weight of overlying layers. C. the Sun absorbs and emits equal amounts of energy. D. the Sun does not change over time.
Answers
Answer: Hydrostatic equilibrium in the Sun means that pressure balances the weight of overlying layers.
Explanation: To find the answer, we have to know more about the Hydrostatic equilibrium in sun.
What is Hydrostatic equilibrium in sun?Hydrostatic equilibrium in sun means that, the sun is neither expanding not contracting.We can say that the forces that control the sun are precisely balanced.The structure of the sun is in such a way that it can balance the pressure outward and the force of gravity inward.This balance is known as hydrostatic equilibrium.Thus, we can conclude that, the Hydrostatic equilibrium in the Sun means that pressure balances the weight of overlying layers.
Learn more about the hydrostatic equilibrium in sun here:
https://brainly.com/question/28044769
#SPJ4
An athlete produced 840 watts of power in 0.6 seconds. How much work did this individual perform during the exercise
Answers
An athlete produced 840 watts of power in 0.6 seconds. And will produce 504 joule of work did this individual perform during the exercise.
Solution:
we know that power is the work done completed in a given interval of time.
Power = [tex]\frac{work}{time}[/tex]
also, Work = Power × Time
Work = 840 × 0.6 = 504 joule
What is Power?
The quantity of work that can be accomplished in a certain amount of time is measured by power.Power is expressed in joules per second (J/s) this is because work is denoted by the symbol J and time by the symbol s.This is the watt, which is also known as the power unit in SI (W). One joule of labor per second is equal to one watt.The number of watts that a device uses is indicated on labels for lightbulbs and other small appliances like microwaves.A force must be applied in order for work to be completed, and there must also be motion or displacement in the force's direction.The amount of force multiplied by the distance moved in the force's direction is known as the work done by a force acting on an item. Work has no direction and only magnitude. Work is a scalar quantity as a result.Know more about work power numerical https://brainly.com/question/181496
#SPJ4
The watermark can be of different types depending on the application. A watermark will resist manipulations of the media. However, a watermark will not resist tampering.
Answers
The first blank is robust watermark; a robust watermark will not resist tampering.
The second blank is fragile watermark; a fragile watermark will resist manipulations of the media.
What is a watermark?A watermark is a faint design made in paper during manufacture that is visible when held against the light and clearly identifies the maker.
The watermark can be of different types depending on the application and they include:
A robust watermark will not resist tampering.A fragile watermark will resist manipulations of the media.Thus, The first blank is robust watermark; a robust watermark will not resist tampering.
The second blank is fragile watermark; a fragile watermark will resist manipulations of the media.
Learn more about watermark here:.
https://brainly.com/question/24206908
#SPJ1
A block of mass 0.248 kg is placed on top of a light, vertical spring of force constant 5 025 N/m and pushed downward so that the spring is compressed by 0.090 m. After the block is released from rest, it travels upward and then leaves the spring. To what maximum height above the point of release does it rise
Answers
The maximum height above the point of release it rises is 8.82 m
What is spring force:
The force exerted by a spring on objects attached to its ends is proportional to the spring's change in length away from its equilibrium length.
F(spring) = k*x
here,
mass, m=0.240 kg
vertical spring constant, k = 5050 N/m
compression, x=0.090 m
When the spring is compressed, the spring potential energy is:
E = (k*x^2) / 2
substituting the values,
E = 5050* 0.090^2 / s
E = 20.91 J
This energy would be converted to kinetic, so the mass gains speed, which is then converted to gravitational potential energy once the mass reaches its highest point
E(p) = m*g*h
where, h is the maximum height
E(p) = E
m*g*h = 20.91
h = 20.91 / ( 9.8 * 0.248 )
h = 8.82 m
hence
The maximum height above the point of release is 8.82 m
Learn more about spring force here:
https://brainly.com/question/14655680
#SPJ4
4. Which is the best season for shearing? Why?
Answers
Answer:
During dry season /Spring
Explanation:
Shearing is the removal of wool from a sheep. When you remove wool from sheep, you subject the sheep to cold since nothing is covering the entire body. Therefore, the most suitable season is during dry periods/ Spring since you won't subjects the sheep to cold but warm environment. Thus important to consider that.
Please give detailed explanation
Answers
Answer:
» (a)
Explanation:
Velocity is the rate of change in displacement.
[tex]{ \rm{velocity = \frac{ \triangle displacement}{time} }} \\ [/tex]
The change from one position to another is displacement or distance between the points.
[tex] = { \rm{ \frac{22000}{200} }} \\ \\ = { \tt{110 \: m {s}^{ - 1} }}[/tex]
Which has a higher reduction potential — silver or iron?
Answers
Answer:
Fe
Explanation:
Dựa vào dãy hoạt động hóa học của kim loại
two particles each having a mass of 5g and charge of 1.0×10^-7C stay in limiting equilibrium on a horizontal table with a separation of 10cm . The coefficient of friction between them and the table is same . Find the value of this coefficient.
Answers
The value of the coefficient is μ=0.18.
What is meant by Friction?A force that opposes this motion of the hands is activated when they brush against one another. The frictional force is the force resisting motion that is exerted in the direction that is counter to the direction that the hands are moving, and it is what creates heat energy.The force that prevents one solid item from moving across another is known as friction. Static, sliding, rolling, and fluid friction are the four main categories of friction.Many times, the uses of friction can be understood by imagining what would happen in their absence. You wouldn't be able to walk, operate a car, or grip anything if there was no friction. Pencils and pencils wouldn't function. Using brakes on a car or bicycle to halt requires friction as well.Find the value of this coefficient.
The particles are in equilibrium, meaning the net force on them is zero.
Thus, repulsion due to their charge = friction due to the table.
As the equilibrium is limiting, friction reaches its maximum value.
[tex]\frac{kQ^{2} }{r^{2} }[/tex]=μmg
[tex]k=9*10^{9} Nm^{2} C^{-2}[/tex]The electrostatic constant [tex]Q=10^{-7} C[/tex] is the charge, and r=0.1m is the distance between the charges.
[tex]\frac{(9*10^{2})(10^{-7})^{2} }{(0.1)^{2} }[/tex]=μ*[tex](5*10^{-3})(10)[/tex]
Therefore, The answer is μ=0.18.
To learn more about friction, refer to:
https://brainly.com/question/24338873
#SPJ9
A billiard ball at rest is struck by another billiard ball of the same mass whose speed is 6.0 m/s. After an elastic collision the striking ball goes off at an angle of 25° with respect to its original direction of motion. Find the angle the struck ball makes with this direction and the final speeds of both balls.
Answers
The angle that the stuck ball makes with the direction of motion and the velocity of both the billiard balls are 65°, 2.6 m/s and 5.5m/s respectively.
To find the answer, we need to know about the linear momentum and angle made in elastic 2 dimensional collision.
What's the angle made by the struck billiard ball with the direction of motion of the 1st ball?In the two dimensional elastic collision between two objects, the scattered objects make 90° angle between them.So, here the angle between the two billiard balls after collision is 90°.As the one billiard ball is making 25° with the initial direction of motion, so the another struck billiard ball makes 90°-25°= 65°.What's the conservation of linear momentum along vertical direction?Let m = mass of each billiard balls, v = velocity of scattered billiard ball, u = velocity of struck billiard ballBefore collision there's no vertical component of momentum. So it's zero.From figure, the total momentum along vertical direction is m×v×sin25°-m×u×sin65°From conservation of linear momentum,0= m×v×sin25°-m×u×sin65°
v×sin25°=u×sin65°
v= 2.1u
What's the conservation of momentum along horizontal direction as shown in figure?Total momentum before the collision along horizontal direction = m × 6 m/sFrom the figure, total momentum after collision is m×v×cos25° + m×u×cos65°So, m×6 = m×v×cos25° + m×u×cos65°6= 2.1u× cos25° +u×cos65°
= 2.33u
u = 6/2.33 = 2.6 m/sAnd v= 2.1×2.6= 5.5 m/sThus, we can conclude that the angle that the stuck ball makes with the direction of motion and the velocity of both the billiard balls are 65°, 2.6 m/s and 5.5m/s respectively.
Learn more about the 2 dimensional collision here:
brainly.com/question/14445985
#SPJ1
A peregrine falcon in a tight, circular turn can attain a centripetal acceleration 1.5 times the free-fall acceleration.
Answers
The acceleration of a body traveling in a circular route is known as centripetal acceleration. The radius of the turn if the falcon will be 19.7 m.
What is Centripetal acceleration?The acceleration of a body traveling in a circular route is known as centripetal acceleration. Because velocity is a vector quantity. It has both a magnitude and a direction.
Given:
a is the centripetal acceleration = 1.5g
v is the velocity = 17 m/sec
To Find:
r is the radius of circular turn = ?
Mathematically centripetal acceleration is given as
a = v^2/r
r = v^2/a. = (17)^2/1.5 x 9.81
r = 19.7 m
Hence the radius of the turn if the falcon will be 19.7 m.
Learn more about Centripetal acceleration here:
https://brainly.com/question/20905151
#SPJ4
An 800-N box is pushed up an inclined plane. The plane is 4.0 m long and 2.0 m high. If it requires 3200 J of work to get the box to the top of the plane, what was the magnitude of the average friction force on the box? Group of answer choices 400 N 0 N Non-zero, but less than 400 N Greater than 400 N
Answers
The magnitude of the average friction force on the box is 400 N
What is energy conservation?
It is the principle by which the total energy remains constant in a system that is not subject to external influence.
It states that energy can neither be created nor be destroyed, It may be transformed from one form to another.
Here,
length of the plane, d = 4 m
height of the plane, h = 2 m
work done total, w = 3200 J
kinetic energy on top, KE = 0
Potential energy on top,
PE = weight x height
PE = 800 *2
PE = 1600 J
Now,
Total work done = KE + PE + W (friction)
W (friction) = 3200 - 1600
W (friction) = 1600 J
W (friction) = F (friction) x d
F (friction) = 1600 / 4
F (friction) = 400 N
Hence,
The magnitude of the average friction force on the box is 400 N
option A is correct
Learn more about friction force here:
https://brainly.com/question/1714663
#SPJ4
irius, the brightest star in the sky, is 2.6 parsecs (8.6 light-years) from Earth, giving it a parallax of 0.379 arcseconds. Another bright star, Regulus , has a parallax of 0.042 arcseconds. What is its distance in parsecs
Answers
The actual distance of Regulus from Earth is 23.81 parsecs.
Given:
Parallax of Regulus, p = 0.042 arc seconds
Calculation:
When an observer changes their position, an apparent change in the object's position takes place. This change can be calculated using the angle ( or semi-angle) made by the observer and object i.e. the angle made between the two lines of observation from the object to the observer.
Thus from the relation of parallax of a celestial body we get:
S = 1/ tan p ≈ 1 / p
where S is the actual distance between the object and the observer
p is the parallax angle observed
Here for Regulus, we get:
S = 1 / p
= 1 / (0.042) [ 1 parsecs = 1 arcseconds ]
= 23.81 parsecs
We know that,
1 parsecs = 3.26 light-years = 206,000 AU
Converting the actual distance into light years we get:
23.81 parsecs = 23.81 × (3.26 light yrs) = 77.658 light-years
Therefore, the actual distance of Regulus from Earth is 23.81 parsecs which is 77.658 in light years.
Learn more about astronomical units here:
https://brainly.com/question/16471213
#SPJ4
True or false: power output can be increased by increasing the rate at which work is done.
Answers
By speeding up the process of doing work, power production may be enhanced. The following statement is true.
Description:
Work is completed at a rate determined by power. It is the ratio of work to time. It may be calculated mathematically using the next equation.
Power = Work / Time
or, P = W / T
If the amount of effort/work increases and the amount of time decreases, power will grow. To complete a task in a short amount of time, a lot of force is used.
The Watt is the common metric unit of power. A quantity of power is one unit of labor divided by one unit of time, as the expression for power suggests. As a result, one Watt is equal to one Joule/second. The term "horsepower" is sometimes used to describe a machine's output of power for historical reasons. The equivalence of horsepower is around 750 Watts.Therefore it is concluded that the questioned statement is true.
Learn more about work here:
https://brainly.com/question/3854047
#SPJ1
PLS GIVE RIGHT ANSWER
I GIVE UP
YOU WILL GET 100 PTS or MORE
Answers
Answer:
it is in explanation part
Explanation:
9
7
3
2
5
8
1
11
14
12
13
Answer:
Explanation:
Why are temperatures in the thermosphere not strictly comparable to those experienced near earth's surface?
Answers
Temperatures in the thermosphere are not strictly comparable to those experienced near Earth's surface because the gases of the thermosphere are moving at very high speeds, and the temperature is very high.
The thermosphere lies among the exosphere and the mesosphere. “Thermo” way warmness and the temperature in this layer can reach as much as 4,500 tiers Fahrenheit. in case you have been to hang around inside the thermosphere, though, you'll be very cold because there are not sufficient fuel molecules to transfer the warmth to you.
The thermosphere is the outer layer of the Earth's surroundings, extending from about 53 miles to greater than 370 miles above the surface. The temperature increases rapidly in this layer due to the absorption of huge quantities of incoming excessive electricity sun radiation by using atoms of nitrogen and oxygen.
Learn more about thermosphere here: https://brainly.com/question/8741747
#SPJ4
In our Solar System, the inner planets are rocky because Choose one: A. warm temperatures in the inner disk caused the inner planetesimals to be formed of mostly rocky material. B. the original cloud had more rocky material near the center. C. the hydrogen and helium atoms were too low mass to remain in the inner disk. D. the inner disk filled a smaller volume, making it denser.
Answers
The inner planets are rocky because The warm temperatures in the inner disk caused the inner planetesimals to be formed of mostly rocky material.
What are rocky planets?
Rocky planets are the planet in which constituents are mostly silicate rocks or metal. They are also regarded as a planet with a solid surface.The formation of rocky planets is said to have occurred billions of years ago and its process of formation is termed accretion. Through accretion are its constituents formed as the more it goes bigger, the higher the rising temperature and pressure in its core and the elements which have to undergo accreted heat up, melt, and spread. Through this process, heavier elements go deeper into the core of the planet and lighter elements float toward the surface. In the formation of rocky planets, the inner portions of the disk are said to be warm from the protostar thereby resulting in the production of the heavy elements that stay there.Examples of rocky planets are Earth or MarsHence, from the above, we can say that,
The warm temperatures in the inner disk caused the inner planetesimals to be formed of mostly rocky material.
Here,
Option A is correct.
Learn more about rocky planets here:
https://brainly.com/question/22392798
#SPJ4
A skydiver falls towards the earth. the attraction of the earth on the diver pulls the diver down. what is the reaction to this force?
Answers
There will be no reaction force acting on the object
Newton's second law is a quantitative description of the changes that a force can produce on the motion of a body. It states that the time rate of change of the momentum of a body is equal in both magnitude and direction to the force imposed on it.
The motion of a free falling object can be described by Newton's second law of motion,
Force (F) = mass * acceleration
a = F / m
The net external force is just the weight of the object (F = W).
Substituting into the second law equation gives:
a = W / m = m * g / m = g .
The acceleration (change of velocity) of the object then becomes the gravitational acceleration.
On freely falling body their is no normal acting on that object
hence , there will be no reaction force acting on the object
To learn more about Newton's second law here
https://brainly.com/question/13447525?referrer=searchResults
#SPJ4
what is the number of moles in 12.04×10²³ particles of NH3?
Answers
Answer:
[tex]\huge\boxed{\sf m = 2 \ moles}[/tex]
Explanation:
Given data:No. of particles = 12.04 × 10²³ particles
Avogadro's number = 6.02 × 10²³
Required:No. of moles = n = ?
Formula:[tex]\displaystyle No. \ of\ moles\ = \frac{no.\ of \ particles}{Avogadro's \ number}[/tex]
Solution:Put the given in the above formula
[tex]\displaystyle n =\frac{12.04 \times 10^{23}}{6.02 \times 10^{23}} \\\\n = 2 \times 1 \ moles\\\\m = 2 \ moles\\\\\rule[225]{225}{2}[/tex]
Intelligence test. If you get it right ,you are a critical thinker. You were in the garden,there are 34 people in the yard. You killed 30. How many people are in the garden.
Answers
The riddle is solved by knowing that there is only one person left in the garden and that is you.
How many people are in the garden?We are told that there were a total of 34 people in the yard. We do not know if these people are in the garden or somewhere around the yard. The next information we have is that a total of 30 persons were killed.
Since you killed them in the garden, the others may still be lurking somewhere in the yard thus there is only one person left in the garden and that is you.
Learn more about solving a riddle:https://brainly.com/question/25063408
#SPJ1
Why is it important on diagrams to represent a force with an arrow? Why should mass NOT be represented by an arrow?
Answers
It is important on diagrams to represent a force with an arrow because force is a vector quantity but it is not important to represent a mass since it is scalar quantity.
Representing a force with arrow and not mass
Vector quantities are always represented with arrows because they have magnitude and direction.
Scalar quantities have only magnitude, and cannot be represented with arrows.
Thus, it is important on diagrams to represent a force with an arrow because force is a vector quantity but it is not important to represent a mass since it is scalar quantity.
Learn more about vector quantities here: https://brainly.com/question/26044328
#SPJ1
Consider a two-dimensional projectile motion problem involving a ball starting and ending at the same height. the projectile leaves the ground with an initial velocity of 10 m/s at some angle theta with the horizontal, (a) what value of the angle theta (in degrees) makes the range of the projectile maximum? explain, (b) what is the range at this angle? (c) how long does it take for the ball to reach maximum height? (d) what is the maximum height?
Answers
The range of the projectile is maximum at angle 45°, the range is 10.2m, the time to reach the maximum height is 0.72 s and the maximum height is 2.6 m
What is a Projectile ?The stone, or object or anything projected in a trajectory path is known as a projectile.
In the given two-dimensional projectile motion problem involving a ball starting and ending at the same height. the projectile leaves the ground with an initial velocity of 10 m/s at some angle Ф with the horizontal,
(a) The value of the angle Ф (in degrees) which will makes the range of the projectile maximum is angle 45° because Range = u²sin2Ф ÷ g
At Ф = 45
Range = u²sin90° ÷ g
where sin 90 = 1
So, Range = u² / g which is the maximum range.
(b) The range at this angle will be
Range = 10² ÷ 9.8
Range = 100 / 9.8
Range = 10.2 m
(c) To calculate how long it takes the ball to reach maximum height, we will use the formula
t = usinФ ÷ g
t = 10 sin 45 ÷ 9.8
t = 0.72s
(d) The maximum height will be
H = u²sin²Ф ÷ 2g
H = 10²(sin45)² ÷ 2 × 9.8
H = 100 × 0.5 ÷ 19.6
H = 50 ÷ 19.6
H = 2.55 m
Therefore, the range of the projectile is maximum at angle 45°, the range is 10.2m, the time to reach the maximum height is 0.72 s and the maximum height is 2.6 m
Learn more about Projectile here: https://brainly.com/question/12870645
#SPJ1
Suppose a fireworks shell explodes, breaking into three large pieces for which air resistance is negligible. How is the motion of the center of mass affected by the explosion
Answers
The center of mass isn't affected by the explosion.
To find the answer, we need to know about the trajectory of motion at zero external force.
How is the trajectory of an object changed when the net external force on it is zero?When there's no net external force acting on an object, its momentum doesn't change with time. As its momentum doesn't change, so it continues with the original trajectory.Why doesn't the trajectory of firework change when it's exploded?When a firework is exploded, its internal forces are changed, but there's no external force. So, although the fragments follow different trajectories, but the trajectory of center of mass remains unchanged.Thus, we can conclude that the center of mass isn't affected by the explosion.
Learn more about the trajectory of exploded firework here:
brainly.com/question/17151547
#SPJ4
On the day Harvey is to present his dissertation, he wakes up with a severe headache. During the presentation, he feels no pain in his head. Fifteen minutes after the presentation is over, Harvey becomes aware of his headache again. Harvey's experience is best explained by
Answers
Gate-control theory
What is Gate-control theory?
According to the Gate Control Theory of Pain, the spinal cord has a system that allows pain signals to be amplified in the brain before being processed at the spinal cord itself, or attenuated there.
The mechanism that allows or prevents the passage of pain signals is known as the gate. The gate may be open or it may be closed, one of two possibilities:
When the gate is open, pain signals can enter and are delivered to the brain, where they are perceived as pain.If the gate is closed, pain signals will be prevented from ascending to the brain and won't be felt.The administration of a non-noxious (soothing or light rubbing) stimulus can help engage the gate control mechanism and alleviate pain in those who are exposed to painful (noxious) stimuli.
Learn more about gate-control theory here:
https://brainly.com/question/15561467
#SPJ4
An ear squeeze occurs when: Select one: The pressure inside the middle ear space is greater than ambient (surrounding) pressure. The pressure inside the middle ear space is less than ambient (surrounding) pressure. Divers forget to wear ear plugs. None of the above.
Answers
B. An ear squeeze occurs when the pressure inside the middle ear space is less than ambient (surrounding) pressure.
When external ear squeeze occursExternal ear squeeze occurs when gas trapped in the external ear canal remains at atmospheric pressure while the external water pressure increases during descent.
Thus, we can conclude that, an ear squeeze occurs when the pressure inside the middle ear space is less than ambient (surrounding) pressure.
Learn more about ear squeeze here: https://brainly.com/question/11430998
#SPJ1
When you lift twice the load twice as high, in half the time, the increase in potential energy is _______.
Answers
If you lift twice the load twice as high, in half the time then, the increase in potential energy is 4 times that of initial potential energy.
To find the answer, we need to know more about the gravitational potential energy.
What to find the potential energy?The form of mechanical energy possessed by a body by virtue of its position is called the potential energy.If the body is under the influence of gravitational field, then the energy possessed by the body is called gravitational potential energy.Given that,[tex]m'=2m\\h'=2h[/tex] where, m' and h' are the final mass and height.
We have the expression for potential energy as,[tex]U=mgh\\[/tex] , let us take this as the initial energy.
Then the final energy will be,[tex]U'=m'gh'=2m*g*2h=4mgh.\\U'=4U[/tex]
Thus, we can conclude that, the final potential energy is 4 times the initial.
Learn more about the gravitational potential energy here:
https://brainly.com/question/28062267
#SPJ1
The final potential energy will be 4 times that of the initial, if we are twice the height and load.
To find the answer, we need to study about the gravitational potential energy.
Where can one find potential energy?Potential energy is the type of mechanical energy that a body possesses as a result of its position.The energy a body possesses is known as gravitational potential energy if it is being affected by a gravitational field.Due to that,[tex]m_f=2m\\h_f=2h[/tex]
where the final mass and height are denoted by mf and hf.
The phrase we use to describe potential energy is,[tex]U_i=mgh[/tex]
let's consider this to be the initial energy.
The final energy will then be,[tex]U_f=2m*2h*g=4mgh=4U_i[/tex]
As a result, we may say that the final potential energy is four times more than the original.
Learn more about gravitational potential energy here:
https://brainly.com/question/13124883
#SPJ1
What does the length of a vector arrow represent?
O A. angle
OB. magnitude
C. direction
OD. force
Answers
Suppose the ski patrol lowers a rescue sled and victim, having a total mass of 90.0 kg, down a p slope at constant speed, as shown below. The coefficient of friction between the sled and the snow is 0.100. (a) How much work is done by friction as the sled moves 30.0 m along the hill
Answers
The work done by friction to move the sled is - 1,323 J.
What is Coefficient of friction?The friction coefficient is the ratio of the normal force pressing two surfaces together to the frictional force preventing motion between them.Typically, it is represented by the Greek letter µ. In terms of math, is equal to F/N, where F stands for frictional force and N for normal force.The coefficient of friction has no dimensions because both F and N are measured in units of force (such as newtons or pounds). For both static and kinetic friction, the coefficient of friction has a range of values.When an object experiences static friction, the frictional force resists any applied force, causing the object to stay at rest until the static frictional force is removed. The frictional force opposes an object's motion in kinetic friction.Solution:
Given that
Coefficient of friction (µ) = 0.10
Mass (m) = 90kg
distance covered (d) = 30m
We use the formula:
friction work = -µmgdcos∅
friction work = -0.100 × 90 kg × 9.8 m/s² × 30 m × cos 60°
friction work = - 1,323 J
Know more about Coefficient of friction numerical https://brainly.com/question/19308401
#SPJ4
Ungrounded alternating-current systems from 50v to 1,000v or less that are not required to be grounded in accordance with article 250.20(b) shall have___________.
Answers
Ungrounded alternating-current systems from 50v to 1,000v or less that are not required to be grounded in accordance with article 250.20(b) shall have ground detectors installed.
What is current system analysis?The current systems is known to be a kind of techniques that are often used to examine the current systems and know the extent of support given to the set of business activities.
A ground detector is known to be a tool that is often use to be able to know or detect conductor insulation that are said to be resistance to ground.
Note that the ground detection is also a sensing equipment that is linked as close as possible to where the system gets its supply and as such, Ungrounded alternating-current systems from 50v to 1,000v or less that are not required to be grounded in accordance with article 250.20(b) shall have ground detectors installed.
Learn more about current systems from
https://brainly.com/question/24858512
#SPJ1