What is the difference between cinema and theatre ?? I want the difference

The minimum required diameter should be 5 mm for each rod.

In physics, stress describes the force acting on a material's unit area. A specific body can become deformed under stress. Strain is the term for the impact that stress has on the body. To restore an object to its original form and size, an opposing force known as a restoring force is produced inside the object. The symbol "σ" stands for stress, which is a tangible quantity. N/m2 is the stress unit in the SI system.

Strength is an object's capacity to withstand the applied stress to the fullest extent possible. Physics distinguishes between two types of stress: Tangential or Shearing Stress and Normal Stress based on the direction of the deforming forces that act on a body.

πd²[tex]_{min}[/tex]/4  = 1962/150

d[tex]_{min}[/tex] = [tex]$ \sqrt{\frac{4 \times 1962}{\Pi \times 150} }[/tex]

d[tex]_{min}[/tex] = 4.081

As, 4 < 4.081 < 5,

The minimum required diameter should be 5 mm for each rod.

Learn more about stress

https://brainly.com/question/25632718

#SPJ4

There will be several advantages to equipment standardization. Digital solutions accelerate standardization by giving an overview of the field equipment.

By using the most effective and efficient procedures, they aid in accelerating the rate of output. Reduce construction costs overall, especially for big contracts. A machine or piece of equipment can effortlessly perform tasks that are too difficult or delicate for human muscles to complete.

In general, they are used to assemble or disassemble objects (such as hammers and nail guns) (e.g., jackhammers and saws). Hand tools and power tools are two common categories for tools. All non-powered instruments are considered hand tools, such as such as pliers and hammers.

To know more about Equipment Sing visit:-

https://brainly.com/question/29667828

#SPJ1

The hydrologic cycle is important because it determines how water gets to ourselves, the plants, and the animals.

The hydrologic cycle is a very important process since it controls our planet's climate and ensures that all living things have access to water. We would run out of clean water, which is essential for life, if water didn't apparently recycle itself. aquatic environments are exposed to pathogens and silt. The continuous movement of water in the atmosphere, on the surface, and underneath the Earth is known as the hydrologic cycle (sometimes referred to as the water cycle). This cycle is the power exchange that affects the weather. Power is released and the environment is warmed when water condenses. The hydrological cycle of the earth's ecosystems is the culmination of all methods used to move water.

Learn more about The hydrologic cycle here:

https://brainly.com/question/30051098

#SPJ4

The curves look like a sine wave, with the number of rabbits and foxes both oscillating around a steady-state equilibrium. The presence of the constants for growth and death of both rabbits and foxes.

What is curves?
Curves is an international fitness franchise targeting women. It offers a 30-minute workout that combines strength training, cardio, and stretching. The circuit-style program is designed to help members reach their fitness goals while providing a supportive, non-threatening environment. The program also includes nutrition counseling, wellness education, and support from certified coaches.

This is because the predator-prey relationships in this system are cyclical, with the fox population increasing as the rabbit population increases, and vice versa.

To learn more about curves
https://brainly.com/question/13445467

#SPJ4

Therefore, (-26.46i-52.92k) Nm is the answer to the presented problem of force.

The definition of force in physics is: The push or pull on a massed object changes its velocity. An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude.

Any of the four fundamental forces in physics—gravitational, electromagnetic, strong, and weak—that control how things or particles interact as well as how some particles decay—is referred to as a fundamental force, also known as a fundamental interaction. These fundamental forces are the source of all known natural forces.

to know more about force here:

brainly.com/question/13191643

#SPJ1

The resulting stress at the top and bottom surfaces is 837.5 N/m^2 and -837.5 N/m^2, respectively. The top surface is in compression and the bottom surface is in tension.

What is stress?
Stress in engineering is the amount of force per unit area placed on a material or structure. It can be physical, or it can be psychological. Stress can be positive or negative. Positive stress can cause a material to become stronger, while negative stress can cause it to become weaker or even fail. Stress can also refer to the amount of strain a material must endure before it yields or breaks. Stress is measured in terms of pounds per square inch (psi) or newtons per square meter (N/m2). Stress analysis is important in engineering as it helps to identify potential failure points in a design, or to determine how much a material can handle before it breaks. Stress analysis is used to ensure the safety and integrity of products, structures, and machines.

To learn more about stress
https://brainly.com/question/13260444

#SPJ4

The statements below that refer to the design and operation of the power sub-system on a spacecraft is option

      7. For a spacecraft in planetary orbit, power for the eclipse period is commonly provided by a battery as a secondary power source, and an increased solar array area to give extra power to charge the batteries whilst not in eclipse.

Radioisotope Thermoelectric Generators (RTGS) are commonly applied to earth-orbiting spacecraft to provide power for the eclipse period when the solar panels are ineffective.

This is because RTGS use the heat generated by the decay of a radioactive material to generate electricity, which allows them to continue to produce power even when the solar panels are not receiving sunlight.

Therefore, Jupiter is considered the approximate limit for solar-powered orbital missions; missions to planets beyond this will require Radioisotope Thermoelectric Generators (RTGS). This is because as you move farther away from the sun, the amount of sunlight received by the solar panels decreases, making it difficult to generate enough power to operate the spacecraft. RTGS are a more reliable power source for missions to these outer planets because they do not rely on sunlight to generate power.

Learn more about spacecraft from

https://brainly.com/question/24571549

#SPJ1

Answer: true

Explanation:

Given statement: smiles.substring(1, 5) returns "mile". This assertion absolutely is true.

In the try block, we transform the string to a Double using the parseDouble() method of Double to determine whether the text solely contains integers. The string isn't a number if it throws an error (such as a NumberFormatException fault), in which case numeric is set to false. It is a number if not.

Similar to declaring a one-dimensional array, a string can be declared easily.  size[char str name]; In the aforementioned syntax, size is used to specify the string's length, or the amount of characters it may hold. Str name is any name supplied to the string variable.

To learn more about string visit:

brainly.com/question/30099412

#SPJ1

Explanation:

A research report is a well-crafted document that outlines the processes, data, and findings of a systematic investigation. It is an important document that serves as a first-hand account of the research process, and it is typically considered an objective and accurate source of information.

(1) to build knowledge and facilitate efficient learning, (2) to understand various issues, (3) to know the truth and prove lies, and (4) to seek opportunities among others

According to the question, the minimum cation-to-anion radius ratio is 8/1 = 0.414.

What is cation-to-anion radius ratio?
The cation-to-anion radius ratio is a measure of the relative sizes of cations and anions in a given compound. It is calculated by dividing the radius of the cation by the radius of the anion.

We will assume that the cation and anion are of equal size.

Let the radius of the cation and anion be r.

The distance between two adjacent cations/anions along a cube edge is 2r, so the length of the cube edge is 2r/2 = r.

The distance between two adjacent cations/anions across a cube face is sqrt(2)r, so the length of the cube face diagonal is sqrt(2)r/2 = r/sqrt(2).

The volume of the cube is (r/2)^3, so the total number of cations and anions inside the cube is (r/2)^3/(2r^3) = 1/8.

Therefore, the minimum cation-to-anion radius ratio is 8/1 = 0.414.

To learn more about cation-to-anion radius ratio
https://brainly.com/question/29564857

#SPJ4

The point where the streamlines, located in the boundary layer of air right next to the wings surface, will separate from the airfoil is called Stall.

What is a Stall?

A stall occurs when an aerofoil's angle of attack exceeds the value that produces maximum lift as a result of airflow across it. This angle is typically around 15° and varies very little in response to the cross section of the (clean) aerofoil.

The airflow across the upper cambered surface ceases to flow smoothly and in contact with the upper surface at the stall and becomes turbulent, greatly reducing lift and increasing drag. The deployment of leading edge or trailing edge devices changes the effective configuration of a wing, which directly affects the angle of attack at which an aerofoil stalls.

All of this, however, assumes a clean wing, and for any aerofoil, contamination of the normally smooth surface by frozen deposits results in a change in the angle of attack at which a stall occurs.

To learn more about Stall, visit:  https://brainly.com/question/30197972

#SPJ4

Answer:

Uber is least comparable to Eventbrite. Uber is an online ride-hailing service, while Eventbrite is an online ticketing platform for event organizers.

Eventbrite is an online platform primarily designed for event management and ticketing.

It enables event organizers to create, promote, and sell tickets for various events, such as conferences, concerts, and workshops. Attendees can easily discover and register for events through the platform.

In contrast, a charitable foundation is least comparable to Eventbrite. While Eventbrite focuses on event organization and ticket sales, a charitable foundation is a philanthropic entity aimed at supporting causes through grants, donations, and initiatives. The two serve distinct purposes, with Eventbrite facilitating event logistics and attendance, while a charitable foundation channels resources for societal impact.

Read more about event management here:

https://brainly.com/question/14195666
#SPJ2

The energy of the magnetic and electric fields that have been stored can differ. A completely charged capacitor is linked in series with an inductor.

A passive-terminal electric device called an inductor, often referred to as a coil, choke, or reactor, stores electricity in a magnetic field when electric current passes through it. An insulated string twisted into a coil is typically included in an inductor. A passive digital component called an inductor can store electrical energy in the form of magnetic electricity. In essence, it uses a conductor that has been twisted into a coil; as electricity enters the coil from left to right, this will produce a magnetic field that rotates counter clockwise. The energy of the magnetic and electric fields that have been stored can differ.

Learn more about Inductor here:

https://brainly.com/question/29417056

#SPJ4

A "While" Loop is used to repeatedly execute a particular block of code until a condition is met.

The responses to the questions are listed below. The operation that determines whether the condition x 10 is true is assessed first because the operator is used first. The reason for this is that we use the post increment operator for x. As a result, x is first used for the operation we are performing before being raised by 1. According to semantics, the variable's value is increased by 1 by both prefix and postfix ++. The result of the operator is the NEW/CURRENT value stored in the variable if the ++ is placed before the variable (a prefix operator); the result of the operator is the value stored in the variable if the ++ is written after the variable (a postfix operator).

Learn more about Operator here:

https://brainly.com/question/30115441

#SPJ4

Answer:

i like icecream

Explanation:

Option A. A diesel electrician works on the electrical systems of diesel engines, while a diesel mechanic works on the mechanical systems of diesel engines.

A diesel electrician focuses on the wiring, electronics, and computer systems of diesel engines, while a diesel mechanic is responsible for the engine parts, fuel systems, and other components.

Both positions require a specific set of skills, and both are necessary to ensure the efficient functioning of diesel engines.

Learn more about diesel electrician: https://brainly.com/question/8118353

#SPJ4

The equation for the streamline passing through point (2,5) is y-5=b/a(x-2).

Streamlining is a process of simplifying or improving a process or system to increase efficiency, reduce complexity, and reduce costs. It can involve reorganizing, restructuring, rearranging, or redefining a system, procedure, or process to make it more efficient and productive.

B) At t=2, the coordinate of the particle that passed through point (0,4) at t=0 is (6,7). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 2a in the x-direction and 2b in the y-direction in the span of 2 seconds. Thus, the displacement of the particle is (2a,2b) = (4,2). Adding this to the initial position (0,4), the new position of the particle is (4,6).
C) At t=3, the coordinate of the particle that passed through point (1,4.25) 2 seconds earlier is (7.25,6.25). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 3a in the x-direction and 3b in the y-direction in the span of 3 seconds. Thus, the displacement of the particle is (3a, 3b) = (6,3). Adding this to the initial position (1,4.25), the new position of the particle is (7,7.25).

To learn more about streamline
https://brainly.com/question/22453879
#SPJ4

The two major grains found on all lumber are the longitudinal grain and the radial grain.

The longitudinal grain runs parallel to the length of the board, while the radial grain runs perpendicular to the length of the board.

The longitudinal grain, also known as the "edge grain," runs parallel to the length of the board.

This grain is created by the growth rings of the tree, which are formed by the tree's annual growth.

When a tree is cut down and milled into lumber, the edge grain is exposed on the edges of the board. This grain is typically considered to be the strongest and most stable of the two grains.

Read more about grain here:

https://brainly.com/question/1394041

#SPJ1

The vessel now holds 4.05 liters of milk, after one-third of this diluted milk is given to three kittens

A stainless steel vessel holds 5.4 liters of milk. One-third of the milk is given to a cat. After some water is added to the milk that remains, its volume becomes 1.25 as much as it was before the water was added.

Before the water was added, the vessel held 5.4 liters of milk. After one-third (1.8 liters) was given to the cat, there was 3.6 liters of milk remaining in the vessel.

After adding water, the volume of the milk increased by a factor of 1.25, so the vessel now holds 4.5 liters (3.6 x 1.25) of diluted milk. Finally, one-third (1.5 liters) of this diluted milk is given to the three kittens, leaving 4.05 liters of milk in the vessel.

For more questions like Diluted milk click the link below:

https://brainly.com/question/10847815

#SPJ4

Disc-type automotive braking systems mechanically apply the brake pads against the disc rotor when the actuator causes the control balls to move up the ball ramp.

Automotive disc braking systems are a safe and reliable form of braking. They are designed to stop the vehicle quickly and safely. These braking systems work by applying pressure from the brake discs to the brake discs mounted on the wheel axle.

This in turn causes the discs to press against the brake calipers, which in turn are applied to the discs. This action results in safe and reliable braking.

These braking systems also have a mechanical parking function, which is activated by the actuator lever. When the lever is activated, the control balls are moved up the ball ramp, which causes the brake discs to be applied to the rotor to ensure safe braking.

Learn more about automotive braking systems:

https://brainly.com/question/28498761

#SPJ4

Tech B is correct, as the firefighters should not risk their lives unless they can do so safely.

What is a Firefighter?

A firefighter, also known as a fireman, is a highly trained individual who works to fight and extinguish fires. They also work to prevent fires, serve as emergency medical technicians (EMT), and investigate fire causes.

Because a firefighter is almost always the first official "on the scene" of a fire, car accident, or other emergency, they are sometimes referred to as "first responders." Some firefighters work as professionals, while others volunteer in their communities.

There are four primary responsibilities and duties: putting out fires, rescuing and caring for the sick and injured, working to prevent future fires, and investigating the causes of fires, particularly if arson is suspected.

To know more about Firefighter, visit: https://brainly.com/question/14252935

#SPJ4

The energy stored in the two rubber bands of the catapult just before release can be calculated as follows: Area of Rubber Bands = (4 mm) x (300 mm) = 1200 mm2, Modulus of Rubber = 10-3 GPa = 10,000 N/mm2 Strain = (3 x Original Length) / (Original Length) =  Energy = (1200 mm2) x (10,000 N/mm2) x (3) = 36,000,000 Nmm or 36,000 J

Energy is the capacity of a physical system to do work or produce heat. It is the fundamental source of virtually all movement and change on Earth. In physics, energy is a property of objects which can be transferred to other objects or converted into different forms. Examples of energy include light, electricity, heat, sound, and kinetic energy. Energy can be generated from a variety of sources including fossil fuels, nuclear power, and renewable sources such as wind, solar, and hydropower. Energy plays a crucial role in the economic and social development of societies, enabling the production of goods and services and the delivery of basic services such as heating, cooling, and lighting. The efficient and responsible use of energy is essential to sustainable development.

To know more about energy here:

brainly.com/question/1932868

#SPJ4

The controller PB is 0.22, the range of the controller pressure is between 3 to 13 psig, the controller setpoint is at 72°F, and the output pressure at that temperature is 3 psig while the controller output pressure at 76°F is 6 psig

A controller system is a type of feedback system used to regulate the performance of an output device by comparing the output to a desired set point. It uses the difference between the two values (error) to continuously adjust a control input to reduce the error. In simple terms, the controller system monitors, adjusts, and regulates the operations of the output device to achieve a desired result. Common examples of controllers include thermostats, cruise control systems, and PID controllers.

(a) Controller PB setting when remote sensors with spans of 50°F, 150°F, and 200°F are used:

This can be calculated as;

PB = (72°F - 50°F) / (200°F - 50°F) = 0.22

(b) Controller pressure range:

The range of the controller pressure is  3 - 13 psig

(c) Controller setpoint:

The controller set point is 72°F

(d)

The controller output pressure when T = 72°F while using the same sensors as in (a) is 3 psig

(e)

The controller output pressure at T = 76°F is  6.6 psig

(f) To predict the output pressure of the controller when T = 80°F with three remote sensors having spans of 50°F, 150°F, and 200°F are used will be 11.2 psig

Learn more on controller system here;

https://brainly.com/question/25480553

#SPJ1

The shear plane angle is calculated as 49.4 degrees while the shear strain is given as 1.17

Shear strain is a measure of deformation resulting from an applied force that is parallel to the surface of an object. It is usually expressed as a fractional change in the length of the object. Shear strain is a measure of the displacement of the surface points of an object in the direction perpendicular to the direction of the applied force.

The shear plane angle is the angle between the plane of shear stress and the normal to the plane of shear. It is typically measured in degrees and can range from 0 to 90 degrees.

(a) Shear plane angle = tan⁻¹((0.65-0.30)/0.30) = 49.4°

(b) Shear strain = (deformed chip thickness - initial chip thickness)/initial chip thickness

Substituting the values into the formula;

Shear Strain = (0.65-0.30)/0.30 = 1.17

learn more on shear strain here;

https://brainly.com/question/22714442

#SPJ1

According to the question of vehicle which is only going to run for a few minutes, tech A is correct.

What is vehicle?
Vehicles are any mode of transportation that can be used on land, sea, or air. They are an important part of modern transportation and include cars, trucks, buses, motorcycles, boats, trains, and airplanes. They provide an efficient way to travel, while also allowing people to transport goods and materials. Vehicles are powered by a variety of sources, including gas and electricity. Advanced technology has allowed for the development of self-driving vehicles, which are becoming increasingly popular.

Caution and danger signs indicate a potentially hazardous situation, and an exhaust extraction hose should be used whenever a vehicle is running, regardless of how long it is running for.

To learn more about vehicle
https://brainly.com/question/28539698

#SPJ4

The data can be plotted as a standard curve. The concentration of Phenobarbital in the unknown can be determined by finding the point on the curve where the fluorescence of the solution intersects the x-axis.

a) The data is plotted in form of a standard curve, which is a graph of the fluorescence of the solutions versus the volume of the standard solution added.

b) By drawing a line of best fit through the data points, we can find the point where the line intersects the x-axis, the x-intercept, which will give us the concentration of phenobarbital in the unknown.

c) The least-squares equation is a mathematical representation of the line of best fit. It is used to find the relationship between two variables by minimizing the sum of the squared residuals between the data points and the line.

d) Using the equation obtained in c), we can calculate the concentration of phenobarbital in the unknown.

e) By using the residuals of the line of best fit, we can calculate the standard deviation of the concentration obtained in d). This will give us an idea of how much the concentration of phenobarbital in the unknown deviates from the actual value.

The least-squares equation can be found by fitting a line to the data points. The concentration of Phenobarbital can then be determined using this equation. The standard deviation for the concentration can be calculated using the residuals from the line of best fit.

Learn more about Phenobarbital here:

brainly.com/question/1939753

#SPJ4

According to the question of tensile stress, 5.66 kips is required to stretch them the required amount and 0.0015 in deflection is require.

What is tensile stress?
Tensile stress is a physical force exerted on a material in opposing directions along its length. It is a measure of the amount of force necessary to pull a material apart, or to cause a fracture. Tensile stress occurs when a material is placed under load and the load is applied in a way that causes the material to elongate. When a material is subjected to tensile stress, the molecules of the material become stretched and the material's shape is changed.

The required force is calculated by multiplying the area of the rod by the desired stress:

F = A * σ = π/4 * (0.75 in)^2 * 30 ksi = 5.66 kips

The required deflection is determined by multiplying the required force by the length of the rod and then dividing by the modulus of elasticity (E) and the area of the rod:

δ = FL/EA = 5.66 kips * 30 ft / (30,000 ksi * π/4 * (0.75 in)2) = 0.0015 in

Therefore, the required force is 5.66 kips and the required deflection is 0.0015 in.

To learn more about tensile stress
https://brainly.com/question/25748369

#SPJ4

The finite automata will be: States: q0, q1, Input Symbols: a, b, Start State: q0, Accepting State: q1, Transition Function:q0 → q1 on input a, q0 → q1 on input b, q1 → q1 on input a, q1 → q1 on input b, Grammar wil be: S → aSb | bSa | ε

Finite Automata is a mathematical model of computation used to recognize patterns within a given sequence of inputs. It consists of a set of states, transitions between those states, and a set of input symbols. It is a powerful tool for recognizing patterns and can be applied to a wide range of applications, such as lexical analysis, pattern recognition, and language recognition. Each state within a finite automaton has a unique set of transitions that can be triggered when a certain input symbol is encountered. This allows the machine to move from one state to another, thus recognizing patterns and making decisions based on the input. Finite automata are typically used in computer science and engineering to design and analyze algorithms.

To learn more about finite automata here:

brainly.com/question/29728092

#SPJ4

Vector parts that are rectangular in shape are referred to as such if their axes are perpendicular to one another.

The rectangular components can be calculated algebraically or graphically, with the force represented as a vector. Knowing two of the six geometric characteristics of a triangle is necessary to resolve a vector into its components, Fx = F cos or Fy = F sin (the lengths of the sides and the three angles).

A vector's rectangular components are any two axes that are perpendicular to one another. An illustration of an example that demonstrates this is provided below. Additional Details: We have the magnitude of any two generic vectors' R's final formula is A2+B2+2ABcos.

To know more about  rectangular visit:-

https://brainly.com/question/11264478

#SPJ1