Which of the following is not a task electricians typically do when maintaining a building’s electrical system?

inspect electrical components, like circuit breakers and transformers

replace insulation to help control and maintain the structure’s environment

supervise and train less skilled workers

repair or replace electrical equipment, fixtures, or wiring

Answer:

1. It is used to test/check the continuity of the circuit

a. Ohmmeter

2. Is a physical  device used to connect electronic test equipment to a device under test

a. Test probes

3. A device inserted to a convenience outlet to conduct electric current

a. Plug

4. Is a stranded wire used to temporary wiring installation and commonly used in extension cord assembly

a. Duplex cord

5. It is a pocket size tool used to test the line wire or circuit if there is a current in it.

a. Test light

6. An instrument used to measure the amount of electrical current intensity in a circuit

b. Ammeter

7. A pocket sized tool used to test the line wire or circuit if there is current in it.

a. Test light

8. A measuring tool used to measure the length of an object in centimeter in it

b) Ruler

9. It is used to measure the diameter of wires/conductors in circular mills. It can measure small and big sizes of wires

a. Micrometer

10. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or series with the circuit depending on what to measure

a) Volt-Ohm-milliammeter

11. It is the measuring tool used to measure length, width and thickness of short object and in sketching straight line

Foot rule/ ruler

Explanation:

1. An Ohmmeter tests resistance of a circuit and therefore, indicates if the circuit has continuity (connectivity) by measuring the resistance to the current it sends through the circuit, while the circuit power is switched off

2. A test probe connects a testing equipment to a Device Under Test (DUT)

3. A plug is used to connect an electric appliance to the mains power supply by fitting it into the mains power outlet

4. A duplex cord is used for temporary wiring to supply power in an extension cord assembly

5. A test light is used to determine if a circuit has electric current flowing in it

6. An ammeter measures the amount of direct or alternating current flowing in a circuit

7. Test light is used to check the presence of an electric current in a circuit

8. A ruler is used to measure length and it is marked in cm or in

9. A micrometer measures the diameter of wires placed in between the anvil and spindle

10. A Volt-Ohm-Milliammeter (VOM), is also known as a multimeter that measures voltage, current, and resistance of a circuit

11. A foot rule/ ruler, measures the dimensions of objects that are flat and short

Logs.

Like data logs. Sometimes people make these logs to keep tabs on other people or to get important information put down somewhere that way it is saved and can be looked back upon later. Anytime someone makes an action on the computer, it makes a TMP file representing a log of what you want it to do before the computer quickly get's rid of the file.

-Ɽ3₮Ɽ0 Ⱬ3Ɽ0

Answer: The BARO sensor informs the PCM about changes in weather and B.altitude

Explanation: The barometric sensor reads the barometric pressure (the density of the atmosphere according to altitude and weather conditions). The barometric pressure (BARO) sensor works in conjunction with the manifold absolute pressure (MAP) sensor to provide constant pressure difference information to the PCM. Barometric pressure is the size of air strain in the atmosphere, in particular the size of the load exerted by way of air molecules at a given point on this planet. The Manifold Absolute pressure sensor performs 'double obligation' as a barometric stress sensor as soon because the key's turned on. With the key became on (prior to the engine starting) there is no vacuum inside the engine applied to the MAP sensor therefore its sign to the ECM will become a BARO studying useful in determining air density.

resistor in series add  so the total resistance is 12 ohms

E=I x R   E = voltage, I = amps, R = resistance

12 = I x 12

I=1 is the answer to the question

E=I x R   E = voltage, I = amps, R = resistance

12 = I x 12

I=1 is the correct answer is the correct answer to the question

Answer:

turn the door knob and push the door or say what kind of door knob it is and that might help to

Explanation:

Answer:

A is continental polar and B Is maritime polar

Answer:

False

Explanation:

Answer:

advantages:

it doesnt cause as much pollution

in some areas wind is easily obtainable

disanvantages:

pricey

cant control wind

it's an eye sore making it bad for real estate

Answer:

Generally, soybeans supplement nitrogen in soil.

Any flowering plant produces pollen for honey production.

Answer:

B

click the picture to see the right answer hope this helps someone :)

Answer:

Never attempt to transfer acetylene from one cylinder to another. not act as a fire stop. Flashback arrestors serve this purpose. Only a qualified technician should repair a regulator.

Explanation:

Explanation:

The end-use industries of thermochromic materials include packaging, printing & coating, medical, textile, industrial, and others. Printing & coating is the fastest-growing end-use industry of thermochromic materials owing to a significant increase in the demand for thermal paper for POS systems. The use of thermochromic materials is gaining momentum for interactive packaging that encourages consumers to take a product off the shelf and use it.

Answer:

C. The boot swells slightly

Explanation:

Friction can be defined as a force that opposes the motion of an object in relation to another.

This ultimately implies that, friction is the opposition to the relative motion of two objects in contact. Therefore, lubrication (lubricants) are used to prevent friction between moving parts.

Generally, grease relief port are created by manufacturers of mechanical parts so as to prevent over-lubrication.

However, when lubricating parts that do not have a grease relief port, inject grease until the boot swells slightly so as to maintain the seal at the ball joints.

Answer:R1.25 x 4

Explanation:

Answer:

Greywater.

Explanation:

Greywater is also known as sullage and it can be defined as any form of gently used wastewater derived from sources within a residential or office building such as showers, washing machines, bathroom sinks, bathroom tub, etc.

Generally, greywater or sullage is completely free of fecal materials (faeces) because it is independent from all toilet activities. However, greywater is not clean for direct use because it usually contains food particles, dirt, oil from dishes, hair, etc.

In this scenario, Anna makes arrangements to reuse waste water that has been used in sinks and showers. Greywater is a term which refers to the waste water that Anna reuses to conserve resources.

Therefore, Anna reuses greywater to conserve resources.

Answer:

Engineering is the use of scientific principles to design and build machines, structures, and other items, including bridges, tunnels, roads, vehicles, and buildings. In other words, Engineering is the use of science and math to design or make things.

Explanation:

Engineering is the application of Science and math problems

Answer:

Explanation:

This tendency to resist changes in their state of motion is described as inertia. Inertia: the resistance an object has to a change in its state of motion. Moving objects, so it was believed, would eventually stop moving; a force was necessary to keep an object moving.

Basically inertia is like something that drives you to do something. It comes in many forms, as stated in a book (the book was Four, of the Divergent series), someone can be tempted to do something because it is what they are used to doing (comfortable with really).

-Ɽ3₮Ɽ0 Ⱬ3Ɽ0

Answer:

  C. exactly vertical

Explanation:

"Plumb" means "exactly vertical."

Answer:

C

Explanation:

The definition of plumb can either be "vertically" or "exactly". In math, the definition of plumb is in face "exactly vertical".

Best of Luck!

Answer:

i dont know or care just need points right now

Explanation:

Answer:

y = 56

Explanation:

We label each of the given equations as follows;

4·x + 2·y = 20...(1)

-8·x - 3·y = 16...(2)

Therefore, we are given a simultaneous equation, question

We make 'x' the subject of both equations and equate the result to find the value of 'y' as follows;

For equation (1)

4·x + 2·y = 20

∴ x = (20 - 2·y)/4 = 5 - y/2

x =  5 - y/2

For equation (2), we have;

-8·x - 3·y = 16

∴ x = (16 + 3·y)/(-8) = -2 - 3·y/8

x = -2 - 3·y/8

Equating the two equations of 'x', gives;

5 - y/2 = -2 - 3·y/8

7 = y/2 - 3·y/8 = (4·y - 3·y)/8 = y/8

∴ 7 = y/8

y = 7 × 8 = 56

y = 56

Answer:

A continuously variable transmission (CVT) is an automatic transmission that can change seamlessly through a continuous range of gear ratios. This contrasts with other transmissions that provide a limited number of gear ratios in fixed steps. The flexibility of a CVT with suitable control may allow the engine to operate at a constant RPM while the vehicle moves at varying speeds.that means the ans is A.

A continuously variable transmission requires a transmission fluid specially formulated for CVT needs. The correct option is C.

Because a CVT operates differently than a traditional step-gear transmission, it requires a unique type of transmission fluid that is formulated to meet its specific performance requirements.

CVT fluid helps to maintain the proper frictional properties of the transmission's belts and pulleys, as well as providing cooling and lubrication for the transmission components.

While CVT fluid should be changed at the manufacturer's recommended intervals, it does not have to be changed as frequently as the fluid in a traditional automatic transmission.

Thus, the correct option is C.

For more details regarding continuously variable transmission, visit:

https://brainly.com/question/24258437

#SPJ2

Out of technician A and technician B, who are saying about hazardous waste drums. Technician B is correct. The correct option is B only.

Chemical waste is collected in suitable containers that can be properly closed. Infectious garbage is kept separate from regular trash in biohazardous waste bins.

Solid radioactive waste generated during radioisotope manipulation is stored in radioactive waste containers. Chart for Hazardous Waste Management: This label, which identifies the facility and waste information, must be placed on used hazardous waste containers.

Bucket liners with hazardous waste bucked labels: These are used to close and label bucket liners. Many industries have already developed methods for dealing with hazardous mercury waste. Waste collection methods in cities have become more efficient in the collection of mercury waste.

Therefore, the correct option is b, B only.

To learn more about hazardous waste, refer to the link:

https://brainly.com/question/14441506

#SPJ2

Answer:

Training is a way for employers to provide tools to enable employees to protect themselves and others from injuries.

Explanation:

Answer:

The above answer is correct ✔️