Two different kinds of losses can happen in a three-phase induction motor. These losses are variable losses that are constant or fixed losses. Fixed or Constant Losses Consta.
Exactly how are stator losses determined?Stator losses, including as stator iron loss and stator copper loss, are financed in part by this power input. Rotor input is provided with the leftover power, or (input electrical power - stator losses). Thus, rotor input P2 equals Pin minus stator losses (stator copper loss and stator iron loss).
What are the induction motor's three-phase losses?Fixed losses, Copper losses, and stray losses are a few types of losses that can occur in three-phase induction motors. Core losses, bearing friction losses, brush friction losses (in wound rotor motors), and windage losses make up the majority of these losses.
To know more about induction motor visit:-
https://brainly.com/question/29664815
#SPJ1
You are designing a highway to AASHTO guidelines on rolling terrain where the design speed will be 65 mi/h. At one section, a 1.25% grade and a -2.25% grade must be connected with an equal-tangent vertical curve. Determine the minimum length of curve to meet SSD requirements
The minimum length of the curve meeting the SSD requirements is 643.72 ft.
What is SSD?
The Stopping Sight Distance (SSD) is the smallest sight distance that is accessible to a driver on a highway at any location long enough to allow the driver to safely stop a vehicle driving at design speed without colliding with any other obstruction.It is a crucial component in traffic engineering.The formula for SSD is given as, [tex]SSD=vt+\frac{v^{2} }{2g(f \pm \frac{n}{100}) }[/tex]From the given question, we have the grades, [tex]g_{1}=+1.25%[/tex], [tex]g_{2}=-2.25%[/tex], and the design speed, [tex]v=65[/tex] mi/h
So, [tex]SSD=vt+\frac{v^{2} }{2g(f \pm \frac{n}{100}) }\\\implies SSD=1.47(65)(2.5)+\frac{65^{2} }{30(0.347826 \pm \frac{1.25}{100}) }\\\implies SSD=630'[/tex]
The length of the vertical curve is given as, [tex]L=2(SSD)-\frac{2158}{A}[/tex]
When SSD>L, we have\
[tex]L=2(630)-\frac{2158}{-2.25-1.25}\\\implies L=1876.57 ft[/tex]
When SSD<L, we have
[tex]L=\frac{A(SSD)^{2} }{2158} \\\implies L=\frac{(-2.25-1.25)(630)^{2} }{2158} \\\implies L=643.72 ft[/tex]
Hence, the minimum length of the vertical curve is 643.721 ft.
To learn more about SSD from the given link
https://brainly.com/question/22279858
#SPJ4
The density of seawater at a free surface where the pressure is 98 kPa is approximately 1030 kg/m3. Taking the bulk modulus of elasticity of seawater to be 2. 34 109N/m2 and expressing variation of pressure with depth z as dp= rgdz determine the density and pressure at a depth of 2500 m. Disregard the effect of temperature. Recall that:(i) The bulk module of elasticity is defined as: (ii) Density is not assumed as constantin this problem
The pressure of seawater will be 2.14*107 N/m2 and the density will be 8.53*103 kg/m3.
What is pressure?Pressure is a type of force applied to an object by another object over a surface area. Pressure is measured in units of force per unit area and is usually expressed in terms of pascals (Pa).
The bulk modulus of elasticity, K, is a measure of the stiffness of a material and is defined as the ratio of bulk stress to the resulting strain. In this problem, we need to calculate the density and pressure at a depth of 2500 m, based on the given bulk modulus and 98 kPa pressure at the surface.
To solve this problem, we will use the equation K = -dp/dρ, where dp is the change in pressure with depth and dρ is the change in density with depth. Since we are given the bulk modulus and pressure on the surface, we can calculate the change in density with depth as follows:
dρ = -K*dp/dz
where dp = rgdz and rg is the gravity of the Earth. Substituting these values, we get:
dρ = -2.34*109*98*103/(9.8*2500) = -7.78*103 kg/m3
This means that for every metre of depth, the density of seawater decreases by 7.78*103 kg/m3. Therefore, at a depth of 2500 m, the density of seawater will be:
ρ = 1030 - 7.78*103*2500 = 8.53*103 kg/m3
Similarly, we can calculate the pressure at a depth of 2500 m using the equation P = P0 + rgdz, where P0 is the pressure at the surface. Substituting the values, we get:
P = 98*103 + 9.8*2500*8.53*103 = 2.14*107 N/m2
Therefore, at a depth of 2500 m, the pressure of seawater will be 2.14*107 N/m2 and the density will be 8.53*103 kg/m3.
To learn more about pressure
https://brainly.com/question/30129462
#SPJ4
(text 2. 36) A belt sander has a belt speed of 1500 ft/min. The coefficient of friction between the sander and the plywood being finished is 0. 2. If the downward (normal) force on the sander is 15 bf, determine (a) the power transmitted by the belt, in Btu/s and hp, and (b) the work done in one minute of sanding, in Btu
a) The power transmitted by the belt, is 5.53 hp and (b) the work done in one minute of sanding, in Btu is 37500 Btu.
What is power?
Power is the ability to influence people, events, and outcomes. It is a fundamental element in the human experience, and it has been studied by scholars and philosophers for centuries. Power can manifest itself in many forms, such as political, economic, military, cultural, or social. It is often used to control or dominate others, and it is used to create and maintain systems of inequality and oppression. Power can also be used for good, such as providing people with the resources and ability to make positive changes in their lives and the world around them.
a) Power Transmitted by the Belt = (15 bf) x (1500 ft/min) x (0.2) = 4500 bf-ft/min = 4500 ft-lb/min = 7500 Btu/s = 5.53 hp
b) Work Done in One Minute of Sanding = (15 bf) x (1500 ft/min) = 22500 ft-lb = 37500 Btu
To learn more about power
https://brainly.com/question/25543272
#SPJ4
what's the difference between programming paradigms ?
Answer:
Programming paradigms are different approaches to programming. Each paradigm is concerned with the way code is written, structured, and organized. The main paradigms are procedural, object-oriented, functional, and logical. Each of these has its own set of rules and principles that guide how code is written and executed. Procedural programming focuses on implementing algorithms and breaking tasks down into smaller steps. Object-oriented programming focuses on breaking tasks down into objects and classes. Functional programming focuses on writing code that is easy to read and maintain. Logical programming focuses on using logic to solve problems.
Explanation:
Hope It Help You
Answer:
A programming paradigm is a style or approach to programming, characterized by the way in which the programmer writes the code. There are several different programming paradigms, including:
Explanation:
Imperative programming: This is the most traditional style of programming, in which the programmer writes code that specifies a series of steps to be carried out in order to solve a problem. Imperative programming languages include C, C++, and Java.
Object-oriented programming: In this style of programming, the programmer writes code in the form of objects, which are self-contained units that combine data and behavior. Object-oriented programming languages include Java, Python, and C#.
Functional programming: In functional programming, the programmer writes code in the form of functions, which are self-contained units that take input and produce output, without modifying any external state. Functional programming languages include Haskell, Lisp, and ML.
Logic programming: In this style of programming, the programmer writes code in the form of logical statements, and the language's runtime system is responsible for finding a solution that satisfies all of the statements. Logic programming languages include Prolog and Mercury.
Declarative programming: In declarative programming, the programmer specifies what the desired result should be, rather than how to achieve it. The language's runtime system is responsible for finding a way to produce the desired result. Declarative programming languages include SQL and regular expressions.
Conider the following language \[ l=\left\{a^{n} b^{m}: n \neq m\right\} \] contruct finite automata, grammar
The finite automata will be: States: q0, q1, Input Symbols: a, b, Start State: q0, Accepting State: q1, Transition Function:q0 → q1 on input a, q0 → q1 on input b, q1 → q1 on input a, q1 → q1 on input b, Grammar wil be: S → aSb | bSa | ε
What are finite automata?Finite Automata is a mathematical model of computation used to recognize patterns within a given sequence of inputs. It consists of a set of states, transitions between those states, and a set of input symbols. It is a powerful tool for recognizing patterns and can be applied to a wide range of applications, such as lexical analysis, pattern recognition, and language recognition. Each state within a finite automaton has a unique set of transitions that can be triggered when a certain input symbol is encountered. This allows the machine to move from one state to another, thus recognizing patterns and making decisions based on the input. Finite automata are typically used in computer science and engineering to design and analyze algorithms.
To learn more about finite automata here:
brainly.com/question/29728092
#SPJ4
Type I motor units could best be described by which of the following in comparison to type II motor units
In comparison to type II motor units, type I motor units could best be described as B: "Type I motor units are recruited first."
Type I or type S (slow) is a slow twitch, a fatigue-resistant unit with the smallest force or twitch tension and slowest contraction. Type I motor unit contains oxidative enzymes. On the other hand, type II or type FR (fast, resistant) is a fast twitch, a fatigue-resistant unit with larger forces and faster contraction times. Type II contains oxidative and glycolytic enzymes.
In a comparison of both type I and type II motor units, type I motor units are found to be recruited first.
"
The complete question:
Type I motor units could best be described by which of the following in comparison to type II motor units
a. Type I motor units are faster than type II.
b. Type I motor units are recruited first.
c. Type I motor units are recruited after type II.
d. Type I motor units are larger than type II.
"
You can learn more about Type I motor units at
https://brainly.com/question/13589753
#SPJ4
An airplane is flying at a standard altitude of 5 km. A pitot tube mounted at the nose measures a stagnation pressure of 0. 957 bar. Assume the airplane is flying at high subsonic speed and flow is compressible.
Required:
Calculate the velocity of airplane
The velocity of airplane will be 317.4 m/s.
The velocity of an airplane flying at a standard altitude of 5 km can be calculated using the stagnation pressure of the pitot tube mounted at the nose.
The stagnation pressure of the pitot tube was measured at 0.957 bar. Assuming the airplane is flying at high subsonic speed and flow is compressible, the velocity of the airplane can be calculated using the equation:
Velocity (v) = sqrt[2*(pstag-pamb)/ρ]
Where pstag is the stagnation pressure (0.957 bar), pamb is the ambient pressure (0.1013 bar at 5 km altitude), and ρ is the air density (1.225 kg/m3).
Plugging in the given values, the velocity of the airplane is 317.4 m/s.
To learn more about airplane, click here:
https://brainly.com/question/24752362
#SPJ4
What is the difference between contact relay and communication relay
Answer: The main difference between contact relays and communication relays is the type of signals that they are designed to handle, with contact relays being used to control the flow of electricity in a circuit and communication relays being used to transmit data or signals from one location to another.
Explanation: The main difference between contact relays and communication relays is the type of signals that they are designed to handle. Contact relays are used to control the flow of electricity in a circuit by opening and closing electrical contacts, while communication relays are used to transmit data or signals from one location to another.Contact relays are typically used in applications where it is necessary to switch electrical circuits on and off, such as in control panels and automated systems. They are usually designed to handle relatively low-frequency electrical signals and are typically not suitable for transmitting data or high-frequency signals.On the other hand, communication relays are used to transmit data or signals from one location to another, and are typically designed to handle a wide range of frequencies and data types. They can be used to transmit voice, data, and video signals over a variety of mediums, including wire, fiber optic cables, and wireless transmission.
There are initially 500 rabbits (x) and 200 foxes (y) on Farmer Oat’s property near Riça, Jofostan. Use Polymath or MATLAB to plot the concentration of foxes and rabbits as a function of time for a period of up to 500 days. The predator–prey relationships are given by the following set of coupled ordinary differential equations:
dx/dt= k1x-k2x. Y
dy/dt= k3x. Y-k4y
Constant for growth of rabbits k1 = 0. 02
Constant for death of rabbits k2 = 0. 00004/(day × no. Of foxes)
Constant for growth of foxes after eating rabbits k3 = 0. 0004/(day × no. Of rabbits)
Constant for death of foxes k4 = 0. 04 What do your results look like for the case of k3 = 0. 00004/(day × no. Of rabbits) and tfinal = 800 days?
Also, plot the number of foxes versus the number of rabbits. Explain why the curves look
The curves look like a sine wave, with the number of rabbits and foxes both oscillating around a steady-state equilibrium. The presence of the constants for growth and death of both rabbits and foxes.
What is curves?
Curves is an international fitness franchise targeting women. It offers a 30-minute workout that combines strength training, cardio, and stretching. The circuit-style program is designed to help members reach their fitness goals while providing a supportive, non-threatening environment. The program also includes nutrition counseling, wellness education, and support from certified coaches.
This is because the predator-prey relationships in this system are cyclical, with the fox population increasing as the rabbit population increases, and vice versa.
To learn more about curves
https://brainly.com/question/13445467
#SPJ4
A flexible pavement is constructed with 5 inches of sand-mix asphaltic wearing surface, 9 inches of dense-graded crushed stone base, and 10 inches of crushed stone subbase. The base has a drainage coefficient of 0.90 while the subbase drainage coefficient is 1.0. Determine the structural number of the pavement.
The structural number of the pavement, constructed with 5 inches of the sand-mix asphaltic wearing surface is 14.5.
The structural number is an estimate of the number of inches of asphaltic wearing surface that a pavement can support without exceeding the allowable structural layer strain. It is calculated by multiplying each layer's drainage coefficient by its thickness and then adding the products together.
T In this case, the 5-inch wearing surface has a drainage coefficient of 0.90, the 9-inch base has a coefficient of 1.0, and the 10-inch subbase has a coefficient of 1.0.
The structural number can be calculated by using the following formula:
SN = (5 x 0.90) + (9 x 1.0) + (10 x 1.0) = 14.5. Therefore, the structural number of the pavement is 14.5.
For more questions like Pavement click the link below:
https://brainly.com/question/14452903
#SPJ4
Tech A says that both caution and danger signs indicate a potentially hazardous situation. Tech B says that an exhaust extraction hose is not needed if the vehicle is only going to run for a few minutes. Who is correct
According to the question of vehicle which is only going to run for a few minutes, tech A is correct.
What is vehicle?
Vehicles are any mode of transportation that can be used on land, sea, or air. They are an important part of modern transportation and include cars, trucks, buses, motorcycles, boats, trains, and airplanes. They provide an efficient way to travel, while also allowing people to transport goods and materials. Vehicles are powered by a variety of sources, including gas and electricity. Advanced technology has allowed for the development of self-driving vehicles, which are becoming increasingly popular.
Caution and danger signs indicate a potentially hazardous situation, and an exhaust extraction hose should be used whenever a vehicle is running, regardless of how long it is running for.
To learn more about vehicle
https://brainly.com/question/28539698
#SPJ4
A flexible pavement has a structural number of 6. If a 36,000 pound single axle is being loaded onto the pavement, how does it compare to a 18,000 pound single axle
The 36,000 pound single axle load is twice as much as the 18,000 pound single axle load, so it is twice as much stress on the pavement.
What is axie load?
Axie Load is a decentralized application (dApp) that allows users to earn cryptocurrency rewards simply by playing games. The platform focuses on providing fun, engaging and rewarding experiences for both gamers and crypto owners. The games are designed to be easy to learn, but difficult to master, making them suitable for players of all skill levels. Axie Load also integrates with popular blockchain projects such as Ethereum, allowing users to store their rewards in their own wallets. With its unique combination of gaming and crypto rewards, Axie Load is an exciting platform for users looking to explore the world of blockchain gaming.
To learn more about axie load
https://brainly.com/question/14452903
#SPJ4
The system ________ can communicate with each other and adjust system operation to match the heat load and operating conditions.
The system automatically can communicate with each other and adjust system operation to match the heat load and operating conditions.
What is system operation?
System operation is the process of managing, controlling, and monitoring the operations of a computer system or network. It encompasses the planning and implementation of system operations, including the coordination of hardware, software, and communication components. System operation includes activities such as system configuration, system monitoring, performance tuning, system backup, system recovery, and system maintenance. System operation ensures that the system or network is secure, reliable, and available to users. It also involves troubleshooting and responding to incidents, analyzing system performance, and identifying areas for improvement. System operation is critical to the success of any organization, as it ensures the availability, reliability, and security of the system or network.
To learn more about system operation
https://brainly.com/question/29990235
#SPJ4
When harmonic distortion is specified as a composite value representing all the harmonics, it is called total harmonic distortion.
Yes, that's correct. THD is typically expressed as a percentage, with lower values indicating a cleaner signal with less distortion.
Total harmonic distortion (THD) is a measure of the harmonic distortion present in a signal and is defined as the ratio of the sum of the powers of all harmonic components to the power of the fundamental frequency.
What is total harmonic distortion?Total harmonic distortion (THD) is a measure of the harmonic distortion present in a signal and is defined as the ratio of the sum of the powers of all harmonic components to the power of the fundamental frequency. THD is typically expressed as a percentage, with lower values indicating a cleaner signal with less distortion.
Complete question:
When harmonic distortion is specified as a composite value representing all the harmonics, it is called total harmonic distortion. ¿True or false?
Learn more about THD:
https://brainly.com/question/16045097
#SPJ4
The angle grinder disc is turned at speeds that range from 5000 to rpm.
The angle grinder disc is turned at speeds that range from 5000 to 12,000 rpm.
What is an angle grinder?
An angle grinder is a tool for rough grinding and cutting. An angle grinder tool with the correct disc can replace a variety of instruments, making even the most time-consuming and labor-intensive tasks faster and easier.
The term rpm refers to the number of times per minute that something will go around in a circle. The term rpm stands for revolutions per minute.' Both engines were set at 2,500 rpm.
Therefore, the angle grinder disc is spun at speeds ranging from 5000 to 12,000 revolutions per minute.
To learn more about angle grinder, refer to the link:
https://brainly.com/question/29563148
#SPJ1
A set of steel reinforcing rods is to be stretched axially in tension to create a tensile stress of 30 ksi prior to being cast in concrete to form a beam. Determine how much force will be required to stretch them the required amount and how much deflection is required. There are 10 rods; each is 0. 75-in diameter and 30 ft long
According to the question of tensile stress, 5.66 kips is required to stretch them the required amount and 0.0015 in deflection is require.
What is tensile stress?
Tensile stress is a physical force exerted on a material in opposing directions along its length. It is a measure of the amount of force necessary to pull a material apart, or to cause a fracture. Tensile stress occurs when a material is placed under load and the load is applied in a way that causes the material to elongate. When a material is subjected to tensile stress, the molecules of the material become stretched and the material's shape is changed.
The required force is calculated by multiplying the area of the rod by the desired stress:
F = A * σ = π/4 * (0.75 in)^2 * 30 ksi = 5.66 kips
The required deflection is determined by multiplying the required force by the length of the rod and then dividing by the modulus of elasticity (E) and the area of the rod:
δ = FL/EA = 5.66 kips * 30 ft / (30,000 ksi * π/4 * (0.75 in)2) = 0.0015 in
Therefore, the required force is 5.66 kips and the required deflection is 0.0015 in.
To learn more about tensile stress
https://brainly.com/question/25748369
#SPJ4
State Four Reasons for using plant and Equipment Sing
There will be several advantages to equipment standardization. Digital solutions accelerate standardization by giving an overview of the field equipment.
What benefit does using equipment provide?By using the most effective and efficient procedures, they aid in accelerating the rate of output. Reduce construction costs overall, especially for big contracts. A machine or piece of equipment can effortlessly perform tasks that are too difficult or delicate for human muscles to complete.
What purposes do tools and equipment serve?In general, they are used to assemble or disassemble objects (such as hammers and nail guns) (e.g., jackhammers and saws). Hand tools and power tools are two common categories for tools. All non-powered instruments are considered hand tools, such as such as pliers and hammers.
To know more about Equipment Sing visit:-
https://brainly.com/question/29667828
#SPJ1
Tech A says that dust masks should be used when painting. Tech B says that a respirator should be used when the TLV for a chemical is exceeded. Who is correct
According to the question of chemical , both Tech A and Tech B are correct.
What is chemical?
Chemistry is a branch of science that studies the composition, structure, and properties of matter, as well as the changes it undergoes during chemical reactions. It is the study of the composition, structure, and properties of matter, and the changes it undergoes during chemical reactions. It involves the study of the interactions between atoms and molecules, and the energy changes that accompany these interactions. Chemistry is a foundational science, as it is necessary to understand the properties and behavior of matter in order to understand the behavior of the elements, molecules, and compounds that make up the world.
Dust masks should be used when painting, and a respirator should be used when the threshold limit value (TLV) for a chemical is exceeded.
To learn more about chemical
https://brainly.com/question/30134631
#SPJ4
B. Directions: For items 9-15, sequence the steps involved on how to accomplish
the form in order to acquire materials. Write letters a lo h on the blank, 'a' being the
first step, and so on. Do this in your Activity Notebook.
8. Write your name as requisitioner
9. List the cost per unit and the total cost.
10. Write the number of required materials.
11. List the unit of materials to be requisitioned.
12. Secure the approval of the supply officer.
13. Enumerate the materials with their description.
1. 4. State the name of the project and date when you requested for materials.
The letters A to H on the blank, 'A' being the first step, and so on is as follows:
8-F, 9-E, 10-B, 11-C, 12-G, 13.D 14.A
What is sequence?In mathematics, a sequence is an ordered list of objects where repetitions are allowed. It has members and is comparable to a set (also called elements, or terms). The number of elements determines the length of the sequence (possibly infinite). In contrast to a set, the same elements can appear multiple times in a sequence at different positions, and unlike a set, the order matters.
Formally, a sequence can be defined as a function from natural numbers (the positions of the sequence's elements) to the elements at each of those positions. You can think of an indexed family, which is a function from any index set, as a generalisation of the concept of a sequence.
Learn more about sequence
https://brainly.com/question/21961097
#SPJ4
The maximum load that a 0. 50 in. Diameter teel rod can upport if the normal tre in the rod mut not exceed 24,000 pi i lb. (preciion of 100)
The maximum load that a 0.50 inch diameter steel rod can support if the normal stress in the rod must not exceed 24,000 psi is 15,772 lb.
What is stress?
Stress in engineering is the amount of force that is applied to a material or structure. It is expressed in terms of pounds per square inch (psi) or megapascals (MPa). Stress can be caused by external forces such as gravity, wind, and temperature, as well as by internal forces such as tension, compression, and shear. When a material is stressed beyond its ability to contain the force, it will eventually fail. Engineers must consider a variety of factors when designing a structure or product to ensure that it can withstand the forces it will encounter in its intended environment. This includes understanding the properties of the materials being used, the effect of temperature and other environmental conditions, and the safety factors that must be applied to ensure the structure does not fail under extreme stress.
To learn more about stress
https://brainly.com/question/14288250
#SPJ4
raw sugar cane is taken into a process to create sugar, which is essentially sucrose. the raw cane is approximately 16% sucrose, 63% water, and the rest fiber by mass. juice from the cane is extracted by passing the cane through a series of crushers. about 5% extra mass of water is added to the sugar cane prior to this step to help in the extraction process. the crushed cane and liquid juice is sent to a filter press that creates a cake that contains 4% of the weight of the cane juice, which has a composition similar to the overall non-fiber content of the raw cane. the filtrate is sent to an evaporator where enough water is evaporated to obtain a pale yellow juice that is 41% water. a
The juice is then sent to a crystallizer where it is cooled and seeded with sugar crystals. The crystals grow in size and are separated from the liquid by centrifugation.
What is a crystallizer?Crystallizer is a type of signal-processing technology most commonly used in audio production. It is designed to add clarity and definition to audio signals by emphasizing the frequencies which are most important to the signal. It works by amplifying the signal in the frequency domain and adding a process of resonance so that certain frequencies are emphasized, giving a more defined sound. Crystallizer is particularly useful in mastering, where it can bring out details and clarity that would otherwise be lost. It can also be used to enhance percussion instruments, making them more present in a mix.
The crystals are then dried and screened to obtain the desired size of sugar crystals. The remaining liquid is sent to a vacuum pan where it is boiled and evaporated until it reaches a concentration of 65% sucrose. The syrup is then cooled and crystallized to obtain the final product, which is refined sugar.
To learn more about crystallizers here:
brainly.com/question/13008800
#SPJ4
Significance of a research report
Explanation:
A research report is a well-crafted document that outlines the processes, data, and findings of a systematic investigation. It is an important document that serves as a first-hand account of the research process, and it is typically considered an objective and accurate source of information.
(1) to build knowledge and facilitate efficient learning, (2) to understand various issues, (3) to know the truth and prove lies, and (4) to seek opportunities among others
Convert n = (5.6 + j6.6) to polar form (A?B
A.B's real component is 0.457. Ab is imaginary component 43.67. A/real B's portion is 1.583. A/imaginary B's part is -0.319.
What is a sample of a science direct conversion?to create a phase transformation in (a substance): to transform alcohol into sugar. To invert or transfer. to assert unauthorized legal title to (personal property).
Consider the following cormplex number.
[tex]$$n=5.6+j 6.6$$[/tex]
Consider the formula for conrplex to polar conversion[tex]$x+j y=r \angle \theta^{\circ}$[/tex]
Where
[tex]$$\begin{aligned}& r=\sqrt{x^2+y^2} \\& \theta=\tan ^{-1}\left(\frac{y}{x}\right)\end{aligned}$$[/tex]
Calculate the magnitude of[tex]$n$.[/tex]
[tex]$$[/tex]
[tex]\begin{aligned}& A=\sqrt{5.6^2+6.6^2} \\& A=8.655\end{aligned}$$[/tex]
Calculate the phase of[tex]$n$.[/tex]
[tex]$$[/tex]
[tex]B=\tan ^{-1}\left(\frac{6.6}{5.5}\right)$$[/tex]
[tex]$$B=49.685^{\circ}$$[/tex]
(b)
Consider the following complex numbers.
[tex]$$\begin{aligned}& A=9.9+j 2.9 \\& B=6.1+j 5.3\end{aligned}$$[/tex]
Calculate[tex]$A \cdot B$.[/tex]
[tex]& A \cdot B=83.36 \angle 57.3^{\circ} \\& \text { Calculate } \frac{A}{B} \\& \frac{A}{B}=\frac{9.9+j 2.9}{6.1+j 5.3} \\& \frac{A}{B}=\frac{9.9+j 2.9}{6.1+j 5.3} \times \frac{6.1-j 5.3}{6.1-j 5.3} \\& \frac{A}{B}=\frac{(9.9+j 2.9)(6.1-j 5.3)}{6.1^2+5.3^2} \\& \frac{A}{B}=1.16-j 0.53 \\[/tex]
[tex]& \frac{A}{B}=\sqrt{1.16^2+0.53^2} \angle \tan ^{-1}\left(\frac{-0.53}{1.16}\right) \\& \frac{A}{B}=1.276 \angle-24.65^n \\& A=8.4 \angle 39^{\circ} \\& B=5.2 \angle 50.4^{\circ} \\& A \cdot B=\left(8.4 \angle 39^{\circ}\right)\left(5.2 \angle 50.4^{\circ}\right) \\[/tex]
[tex]& A \cdot B=(8.4 \times 5.2) \angle 39^{\circ}+50.4^{\circ} \\& A \cdot B=43.68 \angle 89.4^* \\& A \cdot B=43.68 \cos \left(89.4^{\circ}\right)+j 43.68 \sin \left(89.4^{\circ}\right) \\& A \cdot B=0.457+j 43.67 \\&\end{aligned}[/tex]
[tex]$$Calculate $\frac{A}{B}$[/tex]
[tex]$$\begin{aligned}& \frac{A}{B}=\frac{8.4 \angle 39^{\circ}}{5.2 \angle 50.4^{\circ}} \\& \frac{A}{B}=\left(\frac{8.4}{5.2}\right) \angle 39^{\circ}-50.4^{\circ} \\& \frac{A}{B}=1.615 \angle-11.4^{\circ} \\& \frac{A}{B}=1.615 \cos (-11.4)+j 1.615 \sin (-11.4) \\& \frac{A}{B}=1.583-j 0.319\end{aligned}$$[/tex]
Real part of[tex]$A \cdot B$ is $0.457$[/tex]
imaginary part of[tex]$A \cdot B$ is $43.67$[/tex]
Real part of [tex]$\frac{A}{B}$ is $1.583$[/tex]
Imaginary part of[tex]$\frac{A}{B}$ is $1.583$[/tex][tex]$\frac{A}{B}$ is $1.583$[/tex]
To know more about convert visit:
https://brainly.com/question/12053471
#SPJ4
A.B's real component is 0.457. Ab is imaginary component 43.67. A/real B's portion is 1.583. A/imaginary B's part is -0.319.
What is a sample of a science direct conversion?In signal processing, sampling is the reduction of a continuous-time signal to a discrete-time signal. A common example is the conversion of a sound wave to a sequence of "samples".The conversion of digital signals from a given sampling rate to a second, arbitrary sampling rate, with both sampling rates derived from independent clock generators, is revisited. A general approach to arbitrary sampling rate conversion is presented from which two efficient realisations are deduced. The computational expenditure of both realisations is derived under the restriction of finite coefficient wordlengths. Finally, design examples demonstrate how to find the optimised parameters and finite wordlength coefficients of an arbitrary sampling rate converter with minimised expenditure and a prescribed performance.
To learn more about wordlengths refer to:
https://brainly.com/question/15886722
#SPJ4
1. What is a geotechnical investigation? What site investigation should take place before designing concrete foundations? What is a Geotechnical Report? Discuss in detail.
A geotechnical investigation is an assessment of the physical and chemical properties of soil, rock, and other subsurface materials. It is typically carried out in order to evaluate the suitability of the ground for a particular purpose, such as the construction of a building or bridge.
Site investigation is the process of collecting and evaluating data about the soil, rock, and groundwater conditions at a particular location. This is usually done before designing concrete foundations, as the characteristics of the subsurface materials can have a significant impact on the stability and integrity of the foundation.
A geotechnical report is a document that summarizes the results of a geotechnical investigation. It typically includes information about the geology of the site, the properties of the subsurface materials, and any potential geotechnical hazards or issues that may affect the proposed development. The report may also include recommendations for how to address any issues that are identified, such as installing foundation reinforcement or providing additional support for the structure.
Site investigations typically involve a number of different techniques, such as soil and rock sampling, borehole drilling, and laboratory testing. The specific techniques used will depend on the nature of the project and the type of information that is needed.
A child accidentally runs into the street in front of an approaching vehicle. The vehicle is traveling at 40 mi/h. Assuming the road is level, at what distance must the driver first see the child to stop just in time? a) 153.7 ft b) 300.3 ft c) 318.8 ft d) 146.7 ft
Assuming the road is level, the driver must see the child at 300.3 ft to stop just in time. Hence, option C) is the correct answer.
What is the distance needed to stop?The distance travelled between the moment the body decides to stop a moving vehicle and the moment the vehicle comes to a complete stop is known as the stopping distance. The stopping distance, indicated by the letter d, is dependent on a number of variables, including as the road's surface and the driver's reflexes.
What is the frictional stopping distance?The distance the car travels before coming to a halt is known as the stopping distance. It is depending on the vehicle's speed as well as the amount of road-to-wheel friction.
Briefing:Deceleration rate is considered 11.2 ft/s²
a = 11.2 ft/s²
= 1^2/2 = (40 mi/h×5280 ft/1 mi×1 h/3600 s)²/22×11.2=240.07 ft
Stopping distance would be:
= 240.07+ 60.23 ft = 300.3 ft
To learn more about stopping distance visit:
brainly.com/question/24254597
#SPJ1
It is okay to speed 7-10 mph over the posted speed limit.
The police cannot write speeding tickets for that.
Answer:
it is okay depending on how u drive
Technician A says it is your duty to fight a fire to the death to save property. Technician B says do not fight a fire unless you can do so safely. Who is correct
Tech B is correct, as the firefighters should not risk their lives unless they can do so safely.
What is a Firefighter?
A firefighter, also known as a fireman, is a highly trained individual who works to fight and extinguish fires. They also work to prevent fires, serve as emergency medical technicians (EMT), and investigate fire causes.
Because a firefighter is almost always the first official "on the scene" of a fire, car accident, or other emergency, they are sometimes referred to as "first responders." Some firefighters work as professionals, while others volunteer in their communities.
There are four primary responsibilities and duties: putting out fires, rescuing and caring for the sick and injured, working to prevent future fires, and investigating the causes of fires, particularly if arson is suspected.
To know more about Firefighter, visit: https://brainly.com/question/14252935
#SPJ4
Classify the variable as nominal-level, ordinal-level, interval-level, or ratio-level measurement. Number of gallons of water in a swimming pool
The number of gallons in a swimming pool in the given question can be classified as a ratio level measurement.
What is ratio level measurement?The highest of the four hierarchical levels of measurement is the ratio level measurement. Data recording accuracy is determined by the levels or scales of measurement. The measurement becomes more difficult as the level increases.
The features of the other 3 levels are all present in the ratio level. At the ratio level, values can take on a true zero, be categorised, ordered, have equal intervals, and more.
While interval and ratio variables are quantitative variables, nominal and ordinal variables fall under the category of categorical variables. Quantitative data allows for a much wider range of statistical tests than categorical data.
Learn more about ratio level measurement
https://brainly.com/question/14739567
#SPJ4
A series circuit has a power source with a voltage of 12 V and two electrical loads. One load has a resistance of 2 Ω, and the other has a resistance of 4 Ω. What is the difference in voltage across the two loads?
The difference in voltage across the two loads is 6 V.
What is the circuit about?In a series circuit, the total resistance is equal to the sum of the individual resistances. In this case, the total resistance of the circuit is 2 Ω + 4 Ω = 6 Ω.
The current in a series circuit is the same through all of the loads. This means that the same amount of voltage is dropped across each load. Since the power source has a voltage of 12 V, and the total resistance of the circuit is 6 Ω, the current in the circuit can be calculated using Ohm's Law:
I = V/R
= 12 V / 6 Ω
= 2 A.
Since the same current flows through both loads and the same amount of voltage is dropped across each load, there is no difference in voltage across the two loads. Both loads experience a voltage drop of:
12 V / 2
= 6 V.
Learn more about series circuit from
https://brainly.com/question/24707814
#SPJ1
The standard overload protection for a 2 hp, 115 V, single phase motor has a nameplate rating of 21.50 A shall not be rated greater than __________________ amperes.
The standard overload protection for a 2 hp, 115 V, single phase motor has a nameplate rating of 21.50 A shall not be rated greater than 21.50 A amperes.
What is motor?
Motor is an electro-mechanical device which converts electrical energy into mechanical energy. It is widely used in industrial and domestic applications to produce rotational motion for machines. Motors are available in a variety of sizes and types, ranging from small DC motors to large AC synchronous motors. Motors are used to power a wide range of machines, from small fans and pumps to large industrial machines such as elevators, cranes, and conveyors. Motors can be powered by electricity, batteries, or fuel, and can be used to move objects in different directions. Motor control systems can be used to control the speed and direction of a motor, allowing for precise and efficient control of a machine. Motors are essential components of modern machines and are used in a wide variety of devices such as electric vehicles, robots, and home appliances.
To learn more about motor
https://brainly.com/question/13002418
#SPJ4